; -------------------------------------------------------------------------------- ; @Title: CMS32L On-Chip Peripherals ; @Props: Released ; @Author: KRZ ; @Changelog: 2025-02-03 KRZ ; @Manufacturer: CMSEMICON - China Micro Semicon Co., Ltd. ; @Doc: Generated (TRACE32, build: 176489.), based on: ; CMS32L051.svd (Ver. 1.2) ; @Core: Cortex-M0+ ; @Chip: CMS32L051LQ32, CMS32L051LQ48, CMS32L051QN20, CMS32L051QN24, ; CMS32L051QN32, CMS32L051QN40, CMS32L051SS24, CMS32L051TS20 ; @Copyright: (C) 1989-2025 Lauterbach GmbH, licensed for use with TRACE32(R) only ; -------------------------------------------------------------------------------- ; ARM Limited (ARM) is supplying this software for use with Cortex-M\n ; processor based microcontroller, but can be equally used for other\n ; suitable processor architectures. This file can be freely distributed.\n ; Modifications to this file shall be clearly marked.\n ; \n ; THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED\n ; OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF\n ; MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.\n ; ARM SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR\n ; CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER. ; -------------------------------------------------------------------------------- ; $Id: percms32l.per 19100 2025-02-24 14:34:34Z kwisniewski $ AUTOINDENT.ON CENTER TREE ENUMDELIMITER "," base ad:0x0 tree.close "Core Registers (Cortex-M0+)" AUTOINDENT.PUSH AUTOINDENT.OFF tree "System Control" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 0x8 if (CORENAME()=="CORTEXM1") group.long 0x10++0x0b line.long 0x00 "STCSR,SysTick Control and Status Register" bitfld.long 0x00 16. " COUNTFLAG ,Returns 1 if timer counted to 0" "0,1" bitfld.long 0x00 2. " CLKSOURCE ,Always reads as one" "No effect,Processor clock" textline " " bitfld.long 0x00 1. " TICKINT ,Counting down to 0 " "No SysTick,SysTick" bitfld.long 0x00 0. " ENABLE ,Counter enable" "Disabled,Enabled" line.long 0x04 "STRVR,SysTick Reload Value Register" hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,Value to load into the STCVR when the counter reaches 0" line.long 0x08 "STCVR,SysTick Current Value Register" hexmask.long.tbyte 0x08 0.--23. 1. " CURRENT ,Reads return the current value of the SysTick counter" else group.long 0x10++0x0b line.long 0x00 "STCSR,SysTick Control and Status Register" bitfld.long 0x00 16. " COUNTFLAG ,Returns 1 if timer counted to 0" "0,1" bitfld.long 0x00 2. " CLKSOURCE ,Always reads as one" "External clock,Processor clock" textline " " bitfld.long 0x00 1. " TICKINT ,Counting down to 0 " "No SysTick,SysTick" bitfld.long 0x00 0. " ENABLE ,Counter enable" "Disabled,Enabled" line.long 0x04 "STRVR,SysTick Reload Value Register" hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,Value to load into the STCVR when the counter reaches 0" line.long 0x08 "STCVR,SysTick Current Value Register" hexmask.long.tbyte 0x08 0.--23. 1. " CURRENT ,Reads return the current value of the SysTick counter" endif if (CORENAME()=="CORTEXM1") rgroup.long 0x1c++0x03 line.long 0x00 "STCR,SysTick Calibration Value Register" bitfld.long 0x00 31. " NOREF ,Reads as one" "0,1" bitfld.long 0x00 30. " SKEW ,Reads as zero" "0,1" textline " " hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Indicates calibration value is not known" else rgroup.long 0x1c++0x03 line.long 0x00 "STCR,SysTick Calibration Value Register" bitfld.long 0x00 31. " NOREF ,Indicates whether the IMPL_DEF reference clock is provided" "Implemented,Not implemented" bitfld.long 0x00 30. " SKEW ,Indicates whether the 10ms calibration value is exact" "Exact,Inexact" textline " " hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Holds a reload value to be used for 10ms (100Hz) timing subject to system clock skew errors" endif if (CORENAME()=="CORTEXM1") rgroup.long 0xd00++0x03 line.long 0x00 "CPUID,CPU ID Base Register" abitfld.long 0x00 24.--31. " IMPLEMENTER ,Implementer code that Arm has assigned" "0x41=Arm Limited" bitfld.long 0x00 20.--23. " VARIANT ,Variant number to distinguish between different product variants or major revisions of the product" "r0,r1,r2,r3,r4,r5,r6,r7,r8,r9,r10,r11,r12,r13,r14,r15" textline " " bitfld.long 0x00 16.--19. " ARCHITECTURE ,Indicates the architecture version" "0x0,0x1,0x2,0x3,0x4,0x5,0x6,0x7,0x8,0x9,0xA,0xB,ARMv6-M,0xD,0xE,0xF" textline " " abitfld.long 0x00 4.--15. " PARTNO ,Indicates part number" "0xC21=Cortex-M1" bitfld.long 0x00 0.--3. " REVISION ,Revision number to distinguish between different patches of the product" "p0,p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,p11,p12,p13,p14,p15" elif (CORENAME()=="CORTEXM0+") rgroup.long 0xd00++0x03 line.long 0x00 "CPUID,CPU ID Base Register" abitfld.long 0x00 24.--31. " IMPLEMENTER ,Implementer code that Arm has assigned" "0x41=Arm Limited" bitfld.long 0x00 20.--23. " VARIANT ,Variant number to distinguish between different product variants or major revisions of the product" "r0,r1,r2,r3,r4,r5,r6,r7,r8,r9,r10,r11,r12,r13,r14,r15" textline " " bitfld.long 0x00 16.--19. " ARCHITECTURE ,Indicates the architecture version" "0x0,0x1,0x2,0x3,0x4,0x5,0x6,0x7,0x8,0x9,0xA,0xB,ARMv6-M,0xD,0xE,0xF" textline " " abitfld.long 0x00 4.--15. " PARTNO ,Indicates part number" "0xC60=Cortex-M0+" bitfld.long 0x00 0.--3. " REVISION ,Revision number to distinguish between different patches of the product" "p0,p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,p11,p12,p13,p14,p15" else rgroup.long 0xd00++0x03 line.long 0x00 "CPUID,CPU ID Base Register" abitfld.long 0x00 24.--31. " IMPLEMENTER ,Implementer code that Arm has assigned" "0x41=Arm Limited" bitfld.long 0x00 20.--23. " VARIANT ,Variant number to distinguish between different product variants or major revisions of the product" "r0,r1,r2,r3,r4,r5,r6,r7,r8,r9,r10,r11,r12,r13,r14,r15" textline " " bitfld.long 0x00 16.--19. " ARCHITECTURE ,Indicates the architecture version" "0x0,0x1,0x2,0x3,0x4,0x5,0x6,0x7,0x8,0x9,0xA,0xB,ARMv6-M,0xD,0xE,0xF" textline " " abitfld.long 0x00 4.--15. " PARTNO ,Indicates part number" "0xC20=Cortex-M0" bitfld.long 0x00 0.--3. " REVISION ,Revision number to distinguish between different patches of the product" "p0,p1,p2,p3,p4,p5,p6,p7,p8,p9,p10,p11,p12,p13,p14,p15" endif group.long 0xd04++0x03 line.long 0x00 "ICSR,Interrupt Control State Register" bitfld.long 0x00 31. " NMIPENDSET ,Setting this bit will activate an NMI" "No effect,Set pending" bitfld.long 0x00 28. " PENDSVSET ,Set a pending PendSV interrupt" "No effect,Set pending" textline " " bitfld.long 0x00 27. " PENDSVCLR ,Clear a pending PendSV interrupt" "No effect,Clear pending" bitfld.long 0x00 26. " PENDSTSET ,Set a pending SysTick" "No effect,Set pending" textline " " bitfld.long 0x00 25. " PENDSVCLR ,Clear a pending SysTick" "No effect,Clear pending" bitfld.long 0x00 23. " ISRPREEMPT ,Pending exception service" "No service,Service" textline " " bitfld.long 0x00 22. " ISRPENDING ,External interrupt pending flag" "No interrupt,Interrupt" hexmask.long.byte 0x00 12.--17. 1. " VECTPENDING ,Active exception number field" textline " " hexmask.long.byte 0x00 0.--5. 1. " VECTACTIVET ,Active exception number field" if (CORENAME()=="CORTEXM0+") group.long 0xd08++0x03 line.long 0x00 "VTOR,Vector Table Offset Register" hexmask.long 0x00 7.--31. 0x80 " TBLOFF ,Vector table address" else textline " " endif group.long 0xd0c++0x03 line.long 0x00 "AIRCR,Application Interrupt and Reset Control Register" hexmask.long.word 0x00 16.--31. 1. " VECTKEY ,Vector Key" bitfld.long 0x00 15. " ENDIANNESS ,Data endianness bit" "Little-endian,Big-endian" textline " " bitfld.long 0x00 2. " SYSRESETREQ ,System reset setup request" "No effect,Reset" bitfld.long 0x00 1. " VECTCLRACTIVE ,Clears all active state information" "No clear,Clear" group.long 0xd10++0x03 line.long 0x00 "SCR,System Control Register" bitfld.long 0x00 4. " SEVONPEND ,Determines whether an interrupt transition from inactive state to pending state is a wakeup event" "Not wakeup,Wakeup" bitfld.long 0x00 2. " SLEEPDEEP ,Provides a qualifying hint indicating that waking from sleep might take longer" "Not deep sleep,Deep sleep" textline " " bitfld.long 0x00 1. " SLEEPONEXIT ,Determines whether, on an exit from an ISR that returns to the base level of execution priority, the processor enters a sleep state" "Disabled,Enabled" rgroup.long 0xd14++0x03 line.long 0x00 "CCR,Configuration and Control Register" bitfld.long 0x00 9. " STKALIGN ,Indicates whether on exception entry all exceptions are entered with 8-byte stack alignment and the context to restore it is saved" "Reserved,Aligned" bitfld.long 0x00 3. " UNALIGN_TRP ,Indicates that all unaligned accesses results in a Hard Fault" "Reserved,Trapped" group.long 0xd1c++0x0b line.long 0x00 "SHPR2,System Handler Priority Register 2" bitfld.long 0x00 30.--31. " PRI_11 ,Priority of system handler 11-SVCall" "00,01,10,11" line.long 0x04 "SHPR3,System Handler Priority Register 3" bitfld.long 0x04 30.--31. " PRI_15 ,Priority of system handler 15-SysTick" "00,01,10,11" bitfld.long 0x04 22.--23. " PRI_14 ,Priority of system handler 14- PendSV" "00,01,10,11" line.long 0x08 "SHCSR,System Handler Control and State Register" bitfld.long 0x08 15. " SVCALLPENDED ,Reads as 1 if SVCall is pending" "Not pending,Pending" if (CORENAME()=="CORTEXM0+") hgroup.long 0x08++0x03 hide.long 0x00 "ACTLR,Auxiliary Control Register" else textline " " endif else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Memory Protection Unit (MPU)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 15. rgroup.long 0xD90++0x03 line.long 0x00 "MPU_TYPE,MPU Type Register" bitfld.long 0x00 8.--15. 1. " DREGION ,Number of regions supported by the MPU" "0,1,2,3,4,5,6,7,8,?..." group.long 0xD94++0x03 line.long 0x00 "MPU_CTRL,MPU Control Register" bitfld.long 0x00 2. " PRIVDEFENA ,Enables the default memory map as a background region for privileged access" "Disabled,Enabled" bitfld.long 0x00 1. " HFNMIENA ,Handlers executing with priority less than 0 access memory with the MPU enabled or with the MPU disabled" "MPU disabled,MPU enabled" bitfld.long 0x00 0. " ENABLE ,Enables the MPU" "Disabled,Enabled" group.long 0xD98++0x03 line.long 0x00 "MPU_RNR,MPU Region Number Register" hexmask.long.byte 0x00 0.--7. 1. " REGION ,Indicates the memory region accessed by MPU_RBAR and MPU_RASR" tree.close "MPU regions" if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x0 group.long 0xD9C++0x03 "Region 0" saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x0 line.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 0 (not implemented)" saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x0 hide.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x1 group.long 0xD9C++0x03 "Region 1" saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x1 line.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 1 (not implemented)" saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x1 hide.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x2 group.long 0xD9C++0x03 "Region 2" saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x2 line.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 2 (not implemented)" saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x2 hide.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x3 group.long 0xD9C++0x03 "Region 3" saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x3 line.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 3 (not implemented)" saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x3 hide.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x4 group.long 0xD9C++0x03 "Region 4" saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x4 line.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 4 (not implemented)" saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x4 hide.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x5 group.long 0xD9C++0x03 "Region 5" saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x5 line.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 5 (not implemented)" saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x5 hide.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x6 group.long 0xD9C++0x03 "Region 6" saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x6 line.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 6 (not implemented)" saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x6 hide.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6" textline " " textline " " endif if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x7 group.long 0xD9C++0x03 "Region 7" saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region" group.long 0xDA0++0x03 saveout 0xD98 %l 0x7 line.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute" bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-" bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7" textline " " bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable" bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable" bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable" textline " " bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1" bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1" bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1" bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1" bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1" bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1" bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1" bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1" bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB" bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled" else hgroup.long 0xD9C++0x03 "Region 7 (not implemented)" saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7" hgroup.long 0xDA0++0x03 saveout 0xD98 %l 0x7 hide.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7" textline " " textline " " endif tree.end width 0x0b else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Nested Vectored Interrupt Controller (NVIC)" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 12. tree "Interrupt Enable Registers" group.long 0x100++0x03 line.long 0x00 "SET/CLREN,Interrupt Set/Clear Enable Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " SET/CLRENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " SET/CLRENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " SET/CLRENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 28. 0x00 28. 0x80 28. " SET/CLRENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " SET/CLRENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " SET/CLRENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " SET/CLRENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " SET/CLRENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " SET/CLRENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 22. 0x00 22. 0x80 22. " SET/CLRENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " SET/CLRENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " SET/CLRENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " SET/CLRENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " SET/CLRENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " SET/CLRENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 16. 0x00 16. 0x80 16. " SET/CLRENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " SET/CLRENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " SET/CLRENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " SET/CLRENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " SET/CLRENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " SET/CLRENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 10. 0x00 10. 0x80 10. " SET/CLRENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " SET/CLRENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " SET/CLRENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " SET/CLRENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " SET/CLRENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " SET/CLRENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 4. 0x00 4. 0x80 4. " SET/CLRENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " SET/CLRENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " SET/CLRENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " SET/CLRENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " SET/CLRENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled" tree.end tree "Interrupt Pending Registers" group.long 0x200++0x03 line.long 0x00 "SET/CLRPEN,Interrupt Set/Clear Pending Register" setclrfld.long 0x00 31. 0x00 31. 0x80 31. " SET/CLRPEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 30. 0x00 30. 0x80 30. " SET/CLRPEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 29. 0x00 29. 0x80 29. " SET/CLRPEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 28. 0x00 28. 0x80 28. " SET/CLRPEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 27. 0x00 27. 0x80 27. " SET/CLRPEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 26. 0x00 26. 0x80 26. " SET/CLRPEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 25. 0x00 25. 0x80 25. " SET/CLRPEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 24. 0x00 24. 0x80 24. " SET/CLRPEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 23. 0x00 23. 0x80 23. " SET/CLRPEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 22. 0x00 22. 0x80 22. " SET/CLRPEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 21. 0x00 21. 0x80 21. " SET/CLRPEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 20. 0x00 20. 0x80 20. " SET/CLRPEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 19. 0x00 19. 0x80 19. " SET/CLRPEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 18. 0x00 18. 0x80 18. " SET/CLRPEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 17. 0x00 17. 0x80 17. " SET/CLRPEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 16. 0x00 16. 0x80 16. " SET/CLRPEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 15. 0x00 15. 0x80 15. " SET/CLRPEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 14. 0x00 14. 0x80 14. " SET/CLRPEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 13. 0x00 13. 0x80 13. " SET/CLRPEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 12. 0x00 12. 0x80 12. " SET/CLRPEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 11. 0x00 11. 0x80 11. " SET/CLRPEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 10. 0x00 10. 0x80 10. " SET/CLRPEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 9. 0x00 9. 0x80 9. " SET/CLRPEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 8. 0x00 8. 0x80 8. " SET/CLRPEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 7. 0x00 7. 0x80 7. " SET/CLRPEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 6. 0x00 6. 0x80 6. " SET/CLRPEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 5. 0x00 5. 0x80 5. " SET/CLRPEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 4. 0x00 4. 0x80 4. " SET/CLRPEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 3. 0x00 3. 0x80 3. " SET/CLRPEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 2. 0x00 2. 0x80 2. " SET/CLRPEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending" textline " " setclrfld.long 0x00 1. 0x00 1. 0x80 1. " SET/CLRPEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending" setclrfld.long 0x00 0. 0x00 0. 0x80 0. " SET/CLRPEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending" tree.end width 6. tree "Interrupt Priority Registers" group.long 0x400++0x1F line.long 0x00 "INT0,Interrupt Priority Register" bitfld.long 0x00 30.--31. " IP_3 ,Priority of interrupt 3" "0,1,2,3" bitfld.long 0x00 22.--23. " IP_2 ,Priority of interrupt 2" "0,1,2,3" bitfld.long 0x00 14.--15. " IP_1 ,Priority of interrupt 1" "0,1,2,3" bitfld.long 0x00 6.--7. " IP_0 ,Priority of interrupt 0" "0,1,2,3" line.long 0x04 "INT1,Interrupt Priority Register" bitfld.long 0x04 30.--31. " IP_7 ,Priority of interrupt 7" "0,1,2,3" bitfld.long 0x04 22.--23. " IP_6 ,Priority of interrupt 6" "0,1,2,3" bitfld.long 0x04 14.--15. " IP_5 ,Priority of interrupt 5" "0,1,2,3" bitfld.long 0x04 6.--7. " IP_4 ,Priority of interrupt 4" "0,1,2,3" line.long 0x08 "INT2,Interrupt Priority Register" bitfld.long 0x08 30.--31. " IP_11 ,Priority of interrupt 11" "0,1,2,3" bitfld.long 0x08 22.--23. " IP_10 ,Priority of interrupt 10" "0,1,2,3" bitfld.long 0x08 14.--15. " IP_9 ,Priority of interrupt 9" "0,1,2,3" bitfld.long 0x08 6.--7. " IP_8 ,Priority of interrupt 8" "0,1,2,3" line.long 0x0C "INT3,Interrupt Priority Register" bitfld.long 0x0C 30.--31. " IP_15 ,Priority of interrupt 15" "0,1,2,3" bitfld.long 0x0C 22.--23. " IP_14 ,Priority of interrupt 14" "0,1,2,3" bitfld.long 0x0C 14.--15. " IP_13 ,Priority of interrupt 13" "0,1,2,3" bitfld.long 0x0C 6.--7. " IP_12 ,Priority of interrupt 12" "0,1,2,3" line.long 0x10 "INT4,Interrupt Priority Register" bitfld.long 0x10 30.--31. " IP_19 ,Priority of interrupt 19" "0,1,2,3" bitfld.long 0x10 22.--23. " IP_18 ,Priority of interrupt 18" "0,1,2,3" bitfld.long 0x10 14.--15. " IP_17 ,Priority of interrupt 17" "0,1,2,3" bitfld.long 0x10 6.--7. " IP_16 ,Priority of interrupt 16" "0,1,2,3" line.long 0x14 "INT5,Interrupt Priority Register" bitfld.long 0x14 30.--31. " IP_23 ,Priority of interrupt 23" "0,1,2,3" bitfld.long 0x14 22.--23. " IP_22 ,Priority of interrupt 22" "0,1,2,3" bitfld.long 0x14 14.--15. " IP_21 ,Priority of interrupt 21" "0,1,2,3" bitfld.long 0x14 6.--7. " IP_20 ,Priority of interrupt 20" "0,1,2,3" line.long 0x18 "INT6,Interrupt Priority Register" bitfld.long 0x18 30.--31. " IP_27 ,Priority of interrupt 27" "0,1,2,3" bitfld.long 0x18 22.--23. " IP_26 ,Priority of interrupt 26" "0,1,2,3" bitfld.long 0x18 14.--15. " IP_25 ,Priority of interrupt 25" "0,1,2,3" bitfld.long 0x18 6.--7. " IP_24 ,Priority of interrupt 24" "0,1,2,3" line.long 0x1C "INT7,Interrupt Priority Register" bitfld.long 0x1C 30.--31. " IP_31 ,Priority of interrupt 31" "0,1,2,3" bitfld.long 0x1C 22.--23. " IP_30 ,Priority of interrupt 30" "0,1,2,3" bitfld.long 0x1C 14.--15. " IP_29 ,Priority of interrupt 29" "0,1,2,3" bitfld.long 0x1C 6.--7. " IP_28 ,Priority of interrupt 28" "0,1,2,3" tree.end width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Debug" tree "Core Debug" sif COMPonent.AVAILABLE("COREDEBUG") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1)) width 0xA group.long 0xD30++0x03 line.long 0x00 "DFSR,Data Fault Status Register" eventfld.long 0x00 4. " EXTERNAL ,External debug request flag" "No occurred,Occurred" eventfld.long 0x00 3. " VCATCH ,Vector catch flag" "No occurred,Occurred" textline " " eventfld.long 0x00 2. " DWTRAP ,Data Watchpoint flag" "No match,Match" textline " " eventfld.long 0x00 1. " BKPT ,BKPT flag" "No match,Match" eventfld.long 0x00 0. " HALTED ,Halt request flag" "No request,Request" if (CORENAME()=="CORTEXM1") if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x01)==0x00) group.long 0xDF0++0x03 line.long 0x00 "DHCSR,Debug Halting Control and Status Register" bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset" bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not completed,Completed" textline " " bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 19. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 18. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted" bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available" textline " " textline " " textfld " " bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled" else group.long 0xDF0++0x03 line.long 0x00 "DHCSR,Debug Halting Control and Status Register" bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset" bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read" textline " " bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 19. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 18. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted" bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available" textline " " bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked" bitfld.long 0x00 2. " C_STEP ,Steps the core in halted debug" "Not halted,Halted" textline " " bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted" bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled" endif else if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x01)==0x00) group.long 0xDF0++0x03 line.long 0x00 "DHCSR,Debug Halting Control and Status Register" bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset" bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not completed,Completed" textline " " bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core Lockup Status/Debug Key" "Not locked up,Locked up" bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core Sleep Status/Debug Key" "Not sleeping,Sleeping" textline " " bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted" bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available" textline " " textline " " textfld " " bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled" else group.long 0xDF0++0x03 line.long 0x00 "DHCSR,Debug Halting Control and Status Register" bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset" bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read" textline " " bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1" bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1" textline " " bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core Lockup Status/Debug Key" "Not locked up,Locked up" bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core Sleep Status/Debug Key" "Not sleeping,Sleeping" textline " " bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted" bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available" textline " " bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked" bitfld.long 0x00 2. " C_STEP ,Steps the core in halted debug" "Not halted,Halted" textline " " bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted" bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled" endif endif wgroup.long 0xDF4++0x03 line.long 0x00 "DCRSR,Debug Core Selector Register" bitfld.long 0x00 16. " REGWnR ,Register Read/Write" "Read,Write" bitfld.long 0x00 0.--4. " REGSEL ,Register Selection" "R0,R1,R2,R3,R4,R5,R6,R7,R8,R9,R10,R11,R12,Current SP,LR,DebugReturnAddress,xPSR Flags,MSP,PSP,Reserved,CONTROL[1]/PRIMASK[0],?..." group.long 0xDF8++0x07 line.long 0x00 "DCRDR,Debug Core Register Data Register" hexmask.long 0x00 0.--31. 1. " DATA ,Data for reading and writing registers to and from the processor" line.long 0x04 "DEMCR,Debug Exception and Monitor Control Register" bitfld.long 0x04 24. " DWTENA ,Global enable or disable for the DW unit" "Disabled,Enabled" bitfld.long 0x04 10. " VC_HARDERR ,Debug trap on a Hard Fault" "No error,Error" textline " " bitfld.long 0x04 0. " VC_CORERESET ,Reset Vector Catch" "No reset,Reset" width 0x0B else newline textline "COREDEBUG component base address not specified" newline endif tree.end tree "Breakpoint Unit (BPU)" sif COMPonent.AVAILABLE("BPU") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("BPU",-1)) width 8. group.long 0x00++0x03 line.long 0x00 "BP_CTRL,Breakpoint Control Register" bitfld.long 0x00 4.--7. " NUM_CODE1 ,Number of comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" bitfld.long 0x00 1. " KEY ,Key field" "No write,Write" bitfld.long 0x00 0. " ENABLE ,Breakpoint unit enable bit" "Disabled,Enabled" group.long 0x8++0x03 line.long 0x00 "B_COMP0,Breakpoint Comparator Registers 0" bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords" hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address" bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 0" "Disabled,Enabled" group.long 0xC++0x03 line.long 0x00 "B_COMP1,Breakpoint Comparator Registers 1" bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords" hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address" bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 1" "Disabled,Enabled" group.long 0x10++0x03 line.long 0x00 "B_COMP2,Breakpoint Comparator Registers 2" bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords" hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address" bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 2" "Disabled,Enabled" group.long 0x14++0x03 line.long 0x00 "B_COMP3,Breakpoint Comparator Registers 3" bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords" hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address" bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 3" "Disabled,Enabled" else newline textline "BPU component base address not specified" newline endif tree.end tree "Data Watchpoint and Trace Unit (DWT)" sif COMPonent.AVAILABLE("DWT") base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1)) width 14. rgroup.long 0x00++0x03 line.long 0x00 "DW_CTRL,DW Control Register " bitfld.long 0x00 28.--31. " NUM_CODE1 ,Number of comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15" rgroup.long 0x1c++0x03 line.long 0x00 "DW_PCSR,DW Program Counter Sample Register" hexmask.long 0x00 0.--31. 1. " EIASAMPLE ,Execution instruction address sample or 0xFFFFFFFF" group.long 0x20++0x0b line.long 0x00 "DW_COMP0,DW Comparator Register 0" hexmask.long 0x00 0.--31. 1. " COMP1 ,Compare against PC or the data address" line.long 0x04 "DW_MASK0,DW Mask Register 0" hexmask.long.byte 0x04 0.--4. 1. " MASK ,Mask on data address when matching against COMP" line.long 0x08 "DW_FUNCTION0,DW Function Register 0" bitfld.long 0x08 24. " MATCHED ,Comparator match" "No match,Match" bitfld.long 0x08 0.--3. " FUNCTION , Settings for DW Function Registers" "Disabled,Reserved,Reserved,Reserved,On PC match,Read address,Write address,R/W address,?..." group.long 0x30++0x0b line.long 0x00 "DW_COMP1,DW Comparator Register 1" hexmask.long 0x00 0.--31. 1. " COMP ,Compare against PC or the data address" line.long 0x04 "DW_MASK1,DW Mask Register 1 " hexmask.long.byte 0x04 0.--4. 1. " MASK ,Mask on data address when matching against COMP" line.long 0x08 "DW_FUNCTION1,DW Function Register 1" bitfld.long 0x08 24. " MATCHED ,Comparator match" "No match,Match" bitfld.long 0x08 0.--3. " FUNCTION , Settings for DW Function Registers" "Disabled,Reserved,Reserved,Reserved,On PC match,Read address,Write address,R/W address,?..." else newline textline "DWT component base address not specified" newline endif tree.end tree.end AUTOINDENT.POP tree.end tree "ADC (A/D Converter)" base ad:0x40045000 group.byte 0x0++0x0 line.byte 0x0 "ADM0,A/D mode register 0" bitfld.byte 0x0 7. "ADCS,A/D conversion operation control" "0,1" bitfld.byte 0x0 3.--5. "FR,A/D conversion clock (fAD) select" "0,1,2,3,4,5,6,7" bitfld.byte 0x0 0. "ADCE,A/D enable" "0,1" group.byte 0x2++0x0 line.byte 0x0 "ADM1,A/D mode register 1" bitfld.byte 0x0 7. "ADMD,A/D conversion channel select mode" "0: Select mode,1: Scan mode" bitfld.byte 0x0 3. "ADSCM,A/D conversion mode" "0: Sequential conversion mode,1: One-shot conversion mode" group.byte 0x4++0x0 line.byte 0x0 "ADM2,A/D mode register 2" bitfld.byte 0x0 6.--7. "ADREFP,Selection of the + side reference voltage of A/D converter" "0: Supplied from inside AVREF of A/D,?,?,?" bitfld.byte 0x0 3. "ADRCK,the upper limit and lower limit conversion result values" "0,1" bitfld.byte 0x0 1. "CHRDE,output CH number in A/D conversion result in Scan mode" "0,1" group.byte 0x6++0x0 line.byte 0x0 "ADTRG,A/D mode register 2" bitfld.byte 0x0 6.--7. "ADTMD,A/D conversion trigger mode" "0,1,2,3" bitfld.byte 0x0 0.--1. "ADTRS,A/D hard trigger select" "0,1,2,3" group.byte 0x8++0x0 line.byte 0x0 "ADS,Analog input channel specification register" group.word 0xE++0x1 line.word 0x0 "ADCR,12-bit A/D conversion result register" group.byte 0xF++0x0 line.byte 0x0 "ADCRH,Higher 8-bit A/D conversion result register" group.byte 0xB++0x0 line.byte 0x0 "ADUL,Conversion result comparison upper limit setting register" group.byte 0xA++0x0 line.byte 0x0 "ADLL,Conversion result comparison lower limit setting register" group.byte 0x15++0x0 line.byte 0x0 "ADSMPWAIT,A/D sampling wait control register" tree.end tree "BGR (Temperature Sensor)" base ad:0x500660 rgroup.long 0x0++0x7 line.long 0x0 "VBG85,The A/D conversion value of VBGR at 85 degrees and 3.0V reference voltage" line.long 0x4 "VBG25,The A/D conversion value of VBGR at 25 degrees and 3.0V reference voltage" tree.end tree "CGC (Clock Generation Circuit)" base ad:0x40020400 group.byte 0x0++0x1 line.byte 0x0 "CMC,Clock operaton Mode Control Register" bitfld.byte 0x0 7. "EXCLK,External Clock input mode" "0,1" bitfld.byte 0x0 6. "OSCSEL,Main OSC Select" "0,1" newline bitfld.byte 0x0 5. "EXCLKS,External Clock input mode" "0,1" bitfld.byte 0x0 4. "OSCSELS,Sub OSC Select" "0,1" newline bitfld.byte 0x0 1.--2. "AMPHS,Control of XT1 clock oscillation frequency" "0,1,2,3" bitfld.byte 0x0 0. "AMPH,Control of X1 clock oscillation frequency" "0,1" line.byte 0x1 "CSC,Clock operation Status Register" bitfld.byte 0x1 7. "MSTOP,High-speed system clock operation control" "0: X1 oscillator operating or External clock from..,1: X1 oscillator stop or External clock from EXCLK.." bitfld.byte 0x1 6. "XTSTOP,Subsystem clock operation control" "0: XT1 oscillator operating or External clock from..,1: XT1 oscillator stop or External clock from.." newline bitfld.byte 0x1 0. "HIOSTOP,High-speed on-chip oscillator clock operation control" "0: High-speed on-chip oscillator operating,1: High-speed on-chip oscillator stopped" rgroup.byte 0x2++0x0 line.byte 0x0 "OSTC,Oscillation stabilization time counter status" group.byte 0x3++0x1 line.byte 0x0 "OSTS,Oscillation stabilization time select register" line.byte 0x1 "CKC,System clock control register" rbitfld.byte 0x1 7. "CLS,Status of CPU/peripheral hardware clock (fCLK)" "0: Main system clock (fMAIN),1: Subsystem clock (fSUB)" bitfld.byte 0x1 6. "CSS,Selection of CPU/peripheral hardware clock (fCLK)" "0: Main system clock (fMAIN),1: Subsystem clock (fSUB)" newline rbitfld.byte 0x1 5. "MCS,Status of Main system clock (fMAIN)" "0: High-speed on-chip oscillator clock (fIH),1: High-speed system clock (fMX)" bitfld.byte 0x1 4. "MCM0,Main system clock (fMAIN) operation control" "0: Select the high-speed on-chip oscillator clock..,1: Select the high-speed system clock (fMX) as the.." group.byte 0x20++0x0 line.byte 0x0 "PER0,Peripheral enable register 0" bitfld.byte 0x0 7. "RTCEN,Control of the RTC input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 6. "IRDAEN,Control of the IRDA input clock" "0: Disables input clock supply,1: Enables input clock supply" newline bitfld.byte 0x0 5. "ADCEN,Control of the ADC input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 4. "IICA0EN,Control of the IICA0 input clock" "0: Disables input clock supply,1: Enables input clock supply" newline bitfld.byte 0x0 3. "SCI1EN,Control of the SCI1 input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 2. "SCI0EN,Control of the SCI0 input clock" "0: Disables input clock supply,1: Enables input clock supply" newline bitfld.byte 0x0 1. "TM41EN,Control of the TM41 input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 0. "TM40EN,Control of the TM40 input clock" "0: Disables input clock supply,1: Enables input clock supply" group.byte 0x41A++0x0 line.byte 0x0 "PER1,Peripheral enable register 1" bitfld.byte 0x0 7. "SPIEN,Control of the SPI input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 5. "PGACMPEN,Control of the PGACMP input clock" "0: Disables input clock supply,1: Enables input clock supply" newline bitfld.byte 0x0 3. "DMAEN,Control of the DMA input clock" "0: Disables input clock supply,1: Enables input clock supply" bitfld.byte 0x0 2. "EPWMEN,Control of the EPWM input clock" "0: Disables input clock supply,1: Enables input clock supply" group.byte 0x23++0x0 line.byte 0x0 "OSMC,Subsystem clock supply mode control register" bitfld.byte 0x0 7. "RTCLPC,Setting in DEEPSLEEP mode or SLEEP mode while subsystem clock is selected as CPU clock" "0: Enables supply of subsystem clock to peripheral..,1: Stops supply of subsystem clock to peripheral.." bitfld.byte 0x0 4. "WUTMMCK0,Selection of operation clock for real-time clock 15-bit interval timer" "0: The subsystem clock is selected as the..,1: The low-speed on-chip oscillator clock is.." group.byte 0x5++0x2 line.byte 0x0 "LOSCSEL,LOCO Frequency Select register" bitfld.byte 0x0 0. "LOSCSEL,LOCO Frequency Select" "0: LOCO's Frequency is 15K,1: LOCO's Frequency is 30K" line.byte 0x1 "PRCR,LOSCSEL's Protect register" line.byte 0x2 "SUBCKSEL,SubSystem Clock select register" bitfld.byte 0x2 0. "SELLOSC,Select LOSC or SUBOSC" "0: Select SUBOSC as the SubSystem clock,1: Select LOSC as the SubSystem clock" group.byte 0x1820++0x0 line.byte 0x0 "HOCODIV,High-speed on-chip oscillator frequency select register" group.byte 0x1800++0x0 line.byte 0x0 "HIOTRM,High-speed on-chip oscillator trimming register" group.word 0x8++0x1 line.word 0x0 "PMUKEY,Power Manager Key Register" group.byte 0xA++0x0 line.byte 0x0 "PMUCTL,Power Manager Control Register" group.byte 0xC++0x3 line.byte 0x0 "WDTCFG0,WDT Configeration 0 register" line.byte 0x1 "WDTCFG1,WDT Configeration 1 register" line.byte 0x2 "WDTCFG2,WDT Configeration 2 register" line.byte 0x3 "WDTCFG3,WDT Configeration 3 register" group.byte 0x2000++0x0 line.byte 0x0 "HOCOFC,High-speed on-chip oscillator frequency correction register" bitfld.byte 0x0 7. "FCMD,High-speed on-chip oscillator frequency correction operation mode register" "0,1" bitfld.byte 0x0 6. "FCIE,Oscillator stop detected operation selection register" "0,1" newline bitfld.byte 0x0 0. "FCST,Oscillator stop detected object selection register" "0,1" tree.end tree "CRC (General Purpose Cyclic Redundancy Check)" base ad:0x400432F0 group.word 0xA++0x1 line.word 0x0 "CRCD,CRC data register" group.byte 0xBC++0x0 line.byte 0x0 "CRCIN,CRC input register" tree.end tree "DBG (Debug Controller)" base ad:0x4001B000 rgroup.long 0x0++0x3 line.long 0x0 "DBGSTR,Debug status register" bitfld.long 0x0 29. "CDBGPWRUPACK,DBG Power Up Acknowledgement" "0,1" bitfld.long 0x0 28. "CDBGPWRUPREQ,DBG Power Up Request" "0,1" group.long 0x4++0x3 line.long 0x0 "DBGSTOPCR,Debug Stop Control register" bitfld.long 0x0 24. "SWDIS,SWD Disable" "0,1" bitfld.long 0x0 16. "RPERMSK,Mask RAM parity error in debug mode" "0,1" bitfld.long 0x0 2. "RESMSK,Mask internal reset in debug mode" "0,1" bitfld.long 0x0 1. "FRZEN1,Stop Communation family macros when cpu halted" "0,1" bitfld.long 0x0 0. "FRZEN0,Stop Timer family macros when cpu halted" "0,1" tree.end tree "DMA (Enhanced DMA Controller)" base ad:0x40005000 repeat 3. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2)++0x0 line.byte 0x0 "DMAEN$1,DMA activation enable register %s" repeat.end group.long 0x8++0x7 line.long 0x0 "DMABAR,DMA base address register" line.long 0x4 "IFPRCR,DMA Trigger Protect register" repeat 3. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2+0x10)++0x0 line.byte 0x0 "DMAIF$1,DMA Trigger enable register %s" repeat.end tree.end tree "DMAVEC (DMA Vector and Control Data Area)" base ad:0x20000000 repeat 32. (increment 0x0 0x1)(increment 0x0 0x1) group.byte ($2)++0x0 line.byte 0x0 "VEC[$1],DMA vector area" repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x20000020 ad:0x20000030 ad:0x20000040 ad:0x20000050 ad:0x20000060 ad:0x20000070 ad:0x20000080 ad:0x20000090 ad:0x200000A0 ad:0x200000B0 ad:0x200000C0 ad:0x200000D0 ad:0x200000E0 ad:0x200000F0 ad:0x20000100 ad:0x20000110) tree "CTRL[$1]" base $2 group.word ($2)++0x7 line.word 0x0 "DMACR,DMA Control register" bitfld.word 0x0 6.--7. "SZ,Transfer Data size selection" "0: 8 bits,1: 16 bits,2: 32 bits,?" bitfld.word 0x0 5. "RPTINT,Enabling/disabling repeat mode interrupts" "0: Interrupt generation disabled,1: Interrupt generation enabled" bitfld.word 0x0 4. "CHNE,Enabling/disabling chain transfers" "0: Chain transfers disabled,1: Chain transfers enabled" bitfld.word 0x0 3. "DAMOD,Destination address control" "0: Fixed,1: Incremented" newline bitfld.word 0x0 2. "SAMOD,Source address control" "0: Fixed,1: Incremented" bitfld.word 0x0 1. "RPTSEL,Repeat area selection" "0: Transfer destination is the repeat area,1: Transfer source is the repeat area" bitfld.word 0x0 0. "MODE,Transfer mode selection" "0: Normal mode,1: Repeat mode" line.word 0x2 "DMBLS,DMA Block Size register" line.word 0x4 "DMACT,DMA Transfer Count register" line.word 0x6 "DMRLD,DMA Transfer Count Reload register" group.long ($2+0x8)++0x7 line.long 0x0 "DMSAR,DMA Source Address register" line.long 0x4 "DMDAR,DMA Destination Address register" tree.end repeat.end repeat 8. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17)(list ad:0x20000120 ad:0x20000130 ad:0x20000140 ad:0x20000150 ad:0x20000160 ad:0x20000170 ad:0x20000180 ad:0x20000190) tree "CTRL[$1]" base $2 group.word ($2)++0x7 line.word 0x0 "DMACR,DMA Control register" bitfld.word 0x0 6.--7. "SZ,Transfer Data size selection" "0: 8 bits,1: 16 bits,2: 32 bits,?" bitfld.word 0x0 5. "RPTINT,Enabling/disabling repeat mode interrupts" "0: Interrupt generation disabled,1: Interrupt generation enabled" bitfld.word 0x0 4. "CHNE,Enabling/disabling chain transfers" "0: Chain transfers disabled,1: Chain transfers enabled" bitfld.word 0x0 3. "DAMOD,Destination address control" "0: Fixed,1: Incremented" newline bitfld.word 0x0 2. "SAMOD,Source address control" "0: Fixed,1: Incremented" bitfld.word 0x0 1. "RPTSEL,Repeat area selection" "0: Transfer destination is the repeat area,1: Transfer source is the repeat area" bitfld.word 0x0 0. "MODE,Transfer mode selection" "0: Normal mode,1: Repeat mode" line.word 0x2 "DMBLS,DMA Block Size register" line.word 0x4 "DMACT,DMA Transfer Count register" line.word 0x6 "DMRLD,DMA Transfer Count Reload register" group.long ($2+0x8)++0x7 line.long 0x0 "DMSAR,DMA Source Address register" line.long 0x4 "DMDAR,DMA Destination Address register" tree.end repeat.end tree.end tree "ELC (Event Link Controller)" base ad:0x40043400 group.byte 0x0++0xE line.byte 0x0 "ELSELR00,Event output destination select register 00" line.byte 0x1 "ELSELR01,Event output destination select register 01" line.byte 0x2 "ELSELR02,Event output destination select register 02" line.byte 0x3 "ELSELR03,Event output destination select register 03" line.byte 0x4 "ELSELR04,Event output destination select register 04" line.byte 0x5 "ELSELR05,Event output destination select register 05" line.byte 0x6 "ELSELR06,Event output destination select register 06" line.byte 0x7 "ELSELR07,Event output destination select register 07" line.byte 0x8 "ELSELR08,Event output destination select register 08" line.byte 0x9 "ELSELR09,Event output destination select register 09" line.byte 0xA "ELSELR10,Event output destination select register 10" line.byte 0xB "ELSELR11,Event output destination select register 11" line.byte 0xC "ELSELR12,Event output destination select register 12" line.byte 0xD "ELSELR13,Event output destination select register 13" line.byte 0xE "ELSELR14,Event output destination select register 14" tree.end tree "EPWM (Enhanced PWM Controller)" base ad:0x40044400 group.word 0x0++0x1 line.word 0x0 "EPWMSRC,Input source select register" bitfld.word 0x0 0. "SRC0%s,Selsect the source clock of EPWM0%s" "0,1" group.word 0x8++0x1 line.word 0x0 "EPWMCTL,EPWMO0n output control register" bitfld.word 0x0 8. "IE0%s,EPWM0%s output inverted enable register" "0,1" bitfld.word 0x0 0. "OE0%s,EPWM0%s output enable register" "0,1" group.word 0xC++0x1 line.word 0x0 "EPWMSTL,EPWMO0n cutoff output level register" bitfld.word 0x0 14. "IO7%s,EPWM07 output enable register" "0,1" bitfld.word 0x0 12. "IO6%s,EPWM06 output enable register" "0,1" bitfld.word 0x0 10. "IO5%s,EPWM05 output enable register" "0,1" bitfld.word 0x0 8. "IO4%s,EPWM04 output enable register" "0,1" bitfld.word 0x0 6. "IO3%s,EPWM03 output enable register" "0,1" bitfld.word 0x0 4. "IO2%s,EPWM02 output enable register" "0,1" bitfld.word 0x0 2. "IO1%s,EPWM01 output enable register" "0,1" bitfld.word 0x0 0. "IO0%s,EPWM00 output enable register" "0,1" group.word 0x4++0x1 line.word 0x0 "EPWMSTC,EPWMO0n cutoff control register" bitfld.word 0x0 4. "REL_SEL,Cutoff release timing select register" "0,1" bitfld.word 0x0 3. "HS_SEL,Output forced cutoff release mode selection" "0,1" bitfld.word 0x0 2. "IN_EG,Output forced cutoff source edge/output forced cutoff release edge selection" "0,1" bitfld.word 0x0 0. "SC_SEL%s,Cutoff source selection" "0,1" group.word 0x10++0x1 line.word 0x0 "EPWMSTR,Status register" bitfld.word 0x0 1. "SHTFLG,cutoff status register" "0,1" bitfld.word 0x0 0. "HZCLR,software release cutoff register" "0,1" tree.end tree "FMC (Flash Memory Controller)" base ad:0x40020000 group.long 0x0++0x23 line.long 0x0 "FLSTS,Flash status register" bitfld.long 0x0 2. "EVF,Flash hardware verification error flag" "0,1" bitfld.long 0x0 0. "OVF,Flash erase or write operaiton finish" "0,1" line.long 0x4 "FLOPMD1,Flash operation mode register 1" line.long 0x8 "FLOPMD2,Flash operation mode register 2" line.long 0xC "FLERMD,Flash erase mode register" line.long 0x10 "FLCERCNT,Flash chip erase control register" line.long 0x14 "FLSERCNT,Flash sector erase control register" line.long 0x18 "FLNVSCNT,Flash address setup time (Tnvs) control register" line.long 0x1C "FLPROCNT,Flash program control register" line.long 0x20 "FLPROT,Flash protect control register" group.long 0x38++0x7 line.long 0x0 "FLPRVCNT,Flash program recovery time (Trcv) control register" line.long 0x4 "FLERVCNT,Flash erase recovery time (Trcv) control register" tree.end tree "IICA (Standard Serial Interface)" base ad:0x40041A30 group.byte 0x0++0x4 line.byte 0x0 "IICCTL00,IICA control register 0" bitfld.byte 0x0 7. "IICE,I2C operation enable" "0,1" bitfld.byte 0x0 6. "LREL,Exit from communications" "0,1" bitfld.byte 0x0 5. "WREL,Wait cancellation" "0,1" bitfld.byte 0x0 4. "SPIE,Enable generation of interrupt request when stop condition is detected" "0,1" bitfld.byte 0x0 3. "WTIM,Control of wait and interrupt request generation" "0,1" bitfld.byte 0x0 2. "ACKE,Acknowledgment control" "0,1" bitfld.byte 0x0 1. "STT,Start condition trigger" "0,1" bitfld.byte 0x0 0. "SPT,Stop condition trigger" "0,1" line.byte 0x1 "IICCTL01,IICA control register 0" bitfld.byte 0x1 7. "WUP,Control of address match wakeup" "0,1" rbitfld.byte 0x1 5. "CLD,Detection of SCLAn pin level (valid only when IICEn = 1)" "0,1" rbitfld.byte 0x1 4. "DAD,Detection of SDAAn pin level (valid only when IICEn = 1)" "0,1" bitfld.byte 0x1 3. "SMC,Operation mode switching" "0,1" bitfld.byte 0x1 2. "DFC,Digital filter operation control" "0,1" bitfld.byte 0x1 0. "PRS,Operation clock (fMCK) contro" "0,1" line.byte 0x2 "IICWL0,IICA low-level width setting register 0" line.byte 0x3 "IICWH0,IICA high-level width setting register 0" line.byte 0x4 "SVA0,Slave address register 0" group.byte 0x120++0x0 line.byte 0x0 "IICA0,IICA shift register 0" rgroup.byte 0x121++0x0 line.byte 0x0 "IICS0,IICA status register 0" bitfld.byte 0x0 7. "MSTS,Master status check flag" "0,1" bitfld.byte 0x0 6. "ALD,Detection of arbitration loss" "0,1" bitfld.byte 0x0 5. "EXC,Detection of extension code reception" "0,1" bitfld.byte 0x0 4. "COI,Detection of matching addresses" "0,1" bitfld.byte 0x0 3. "TRC,Detection of transmit/receive status" "0,1" bitfld.byte 0x0 2. "ACKD,Detection of acknowledge (ACK)" "0,1" bitfld.byte 0x0 1. "STD,Detection of start condition" "0,1" bitfld.byte 0x0 0. "SPD,Detection of stop condition" "0,1" group.byte 0x122++0x0 line.byte 0x0 "IICF0,IICA flag register 0" rbitfld.byte 0x0 7. "STCF,STT clear flag" "0,1" rbitfld.byte 0x0 6. "IICBSY,I2C bus status flag" "0,1" bitfld.byte 0x0 1. "STCEN,Initial start enable trigger" "0,1" bitfld.byte 0x0 0. "IICRSV,Communication reservation function disable bit" "0,1" tree.end tree "INT (Interrupt Controller)" base ad:0x40006000 repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40006000 ad:0x40006004 ad:0x40006008 ad:0x4000600C ad:0x40006010 ad:0x40006014 ad:0x40006018 ad:0x4000601C ad:0x40006020 ad:0x40006024 ad:0x40006028 ad:0x4000602C ad:0x40006030 ad:0x40006034 ad:0x40006038 ad:0x4000603C) tree "IF[$1]" base $2 group.byte ($2)++0x0 line.byte 0x0 "IFL,Interrupt flag register" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40006040 ad:0x40006044 ad:0x40006048 ad:0x4000604C ad:0x40006050 ad:0x40006054 ad:0x40006058 ad:0x4000605C ad:0x40006060 ad:0x40006064 ad:0x40006068 ad:0x4000606C ad:0x40006070 ad:0x40006074 ad:0x40006078 ad:0x4000607C) tree "IF[$1]" base $2 group.byte ($2)++0x0 line.byte 0x0 "IFL,Interrupt flag register" tree.end repeat.end repeat 16. (list 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0xA 0xB 0xC 0xD 0xE 0xF)(list ad:0x40006100 ad:0x40006104 ad:0x40006108 ad:0x4000610C ad:0x40006110 ad:0x40006114 ad:0x40006118 ad:0x4000611C ad:0x40006120 ad:0x40006124 ad:0x40006128 ad:0x4000612C ad:0x40006130 ad:0x40006134 ad:0x40006138 ad:0x4000613C) tree "MK[$1]" base $2 group.byte ($2)++0x0 line.byte 0x0 "MKL,Interrupt mask register" tree.end repeat.end repeat 16. (list 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F)(list ad:0x40006140 ad:0x40006144 ad:0x40006148 ad:0x4000614C ad:0x40006150 ad:0x40006154 ad:0x40006158 ad:0x4000615C ad:0x40006160 ad:0x40006164 ad:0x40006168 ad:0x4000616C ad:0x40006170 ad:0x40006174 ad:0x40006178 ad:0x4000617C) tree "MK[$1]" base $2 group.byte ($2)++0x0 line.byte 0x0 "MKL,Interrupt mask register" tree.end repeat.end tree.end tree "INTM" base ad:0x40045B38 group.byte 0x0++0x1 line.byte 0x0 "EGP0,External interrupt rising edge enable register" bitfld.byte 0x0 3. "EGP3" "0,1" bitfld.byte 0x0 2. "EGP2" "0,1" bitfld.byte 0x0 1. "EGP1" "0,1" bitfld.byte 0x0 0. "EGP0" "0,1" line.byte 0x1 "EGN0,External interrupt falling edge enable register" bitfld.byte 0x1 3. "EGN3" "0,1" bitfld.byte 0x1 2. "EGN2" "0,1" bitfld.byte 0x1 1. "EGN1" "0,1" bitfld.byte 0x1 0. "EGN0" "0,1" tree.end tree "IRDA (Infrared Data Association)" base ad:0x400440A0 group.long 0x0++0x3 line.long 0x0 "IRCR,IrDA control register" bitfld.long 0x0 7. "IRE,IrRxD enable" "0,1" bitfld.long 0x0 4.--6. "IRCKS,IrRxD clock selection" "0,1,2,3,4,5,6,7" bitfld.long 0x0 3. "IRTXINV,IrRxD data polarity switching" "0,1" bitfld.long 0x0 2. "IRRXINV,IrRxD data polarity switching" "0,1" tree.end tree "KEY (Key Interrupt)" base ad:0x40044B30 group.byte 0x7++0x0 line.byte 0x0 "KRM,Key return mode register" tree.end tree "LVD (Voltage Detection Circuit)" base ad:0x40020440 rgroup.byte 0x1++0x0 line.byte 0x0 "LVIM,Voltage detection register" bitfld.byte 0x0 7. "LVISEN,Enable rewritting LVIS register" "0: Disabling of rewriting the LVIS register,1: Enabling of rewriting the LVIS register" bitfld.byte 0x0 1. "LVIOMSK,Mask status flag of LVD output" "0: Mask of LVD output is invalid,1: Mask of LVD output is valid" newline bitfld.byte 0x0 0. "LVIF,Voltage detection flag" "0: Supply voltage (VDD) greater or equal to..,1: Supply voltage (VDD) less than detection voltage.." group.byte 0x2++0x0 line.byte 0x0 "LVIS,Voltage detection level register" bitfld.byte 0x0 7. "LVIMD,Operation mode of voltage detection" "0: interrupt mode,1: reset mode" bitfld.byte 0x0 0. "LVILV,LVD detection level" "0: High-voltage detection level (VLVDH),1: Low-voltage detection level (VLVDL or VLVD)" tree.end tree "MISC (Miscellaneous Functions)" base ad:0x40040470 group.byte 0x0++0x5 line.byte 0x0 "NFEN0,Noise filter enable register 0" bitfld.byte 0x0 4. "SNFEN20,Enable noise filter of RxD2" "0,1" bitfld.byte 0x0 2. "SNFEN10,Enable noise filter of RxD1" "0,1" bitfld.byte 0x0 0. "SNFEN00,Enable noise filter of RxD0" "0,1" line.byte 0x1 "NFEN1,Noise filter enable register 1" bitfld.byte 0x1 3. "TNFEN03,Enable noise filter of TI03" "0,1" bitfld.byte 0x1 2. "TNFEN02,Enable noise filter of TI02" "0,1" bitfld.byte 0x1 1. "TNFEN01,Enable noise filter of TI01" "0,1" bitfld.byte 0x1 0. "TNFEN00,Enable noise filter of TI00" "0,1" line.byte 0x2 "NFEN2,Noise filter enable register 2" bitfld.byte 0x2 3. "TNFEN13,Enable noise filter of TI13" "0,1" bitfld.byte 0x2 2. "TNFEN12,Enable noise filter of TI12" "0,1" bitfld.byte 0x2 1. "TNFEN11,Enable noise filter of TI11" "0,1" bitfld.byte 0x2 0. "TNFEN10,Enable noise filter of TI10" "0,1" line.byte 0x3 "ISC,Input switch control register" bitfld.byte 0x3 7. "SSIE00,The slave select input (SS00) of SPI00 is valid" "0: The slave select input (SS00) pin is invalid,1: The slave select input (SS00) pin is valid" line.byte 0x4 "TIOS0,Timer I/O select register 0" line.byte 0x5 "TIOS1,Timer I/O select register 1" group.byte 0xC++0x0 line.byte 0x0 "RTCCL,Real-time clock select register" tree.end tree "PCBZ (Clock Output/Buzzer Output Controller)" base ad:0x40040FA0 group.byte 0x5++0x1 line.byte 0x0 "CKS0,Clock output select registers 0" bitfld.byte 0x0 7. "PCLOE,PCLBUZn pin output enable" "0,1" bitfld.byte 0x0 3. "CSEL,PCLBUZn output clock select" "0,1" bitfld.byte 0x0 0.--2. "CCS,PCLBUZn output clock select" "0,1,2,3,4,5,6,7" line.byte 0x1 "CKS1,Clock output select registers 1" bitfld.byte 0x1 7. "PCLOE,PCLBUZn pin output enable" "0,1" bitfld.byte 0x1 3. "CSEL,PCLBUZn output clock select" "0,1" bitfld.byte 0x1 0.--2. "CCS,PCLBUZn output clock select" "0,1,2,3,4,5,6,7" tree.end tree "PORT (Pin-Port Function)" base ad:0x40040000 group.byte 0x20++0x7 line.byte 0x0 "PM0,Port mode register 0" line.byte 0x1 "PM1,Port mode register 1" line.byte 0x2 "PM2,Port mode register 2" line.byte 0x3 "PM3,Port mode register 3" line.byte 0x4 "PM4,Port mode register 4" line.byte 0x5 "PM5,Port mode register 5" line.byte 0x6 "PM6,Port mode register 6" line.byte 0x7 "PM7,Port mode register 7" group.byte 0x2C++0x2 line.byte 0x0 "PM12,Port mode register 12" line.byte 0x1 "PM13,Port mode register 13" line.byte 0x2 "PM14,Port mode register 14" group.byte 0x0++0x7 line.byte 0x0 "P0,Port register 0" line.byte 0x1 "P1,Port register 1" line.byte 0x2 "P2,Port register 2" line.byte 0x3 "P3,Port register 3" line.byte 0x4 "P4,Port register 4" line.byte 0x5 "P5,Port register 5" line.byte 0x6 "P6,Port register 6" line.byte 0x7 "P7,Port register 7" group.byte 0xC++0x2 line.byte 0x0 "P12,Port register 12" line.byte 0x1 "P13,Port register 13" line.byte 0x2 "P14,Port register 14" group.byte 0x30++0x7 line.byte 0x0 "PU0,Pull-up resistor option register 0" line.byte 0x1 "PU1,Pull-up resistor option register 1" line.byte 0x2 "PU2,Pull-up resistor option register 2" line.byte 0x3 "PU3,Pull-up resistor option register 3" line.byte 0x4 "PU4,Pull-up resistor option register 4" line.byte 0x5 "PU5,Pull-up resistor option register 5" line.byte 0x6 "PU6,Pull-up resistor option register 6" line.byte 0x7 "PU7,Pull-up resistor option register 7" group.byte 0x3C++0x2 line.byte 0x0 "PU12,Pull-up resistor option register 12" line.byte 0x1 "PU13,Pull-up resistor option register 13" line.byte 0x2 "PU14,Pull-up resistor option register 14" group.byte 0x40++0x3 line.byte 0x0 "PD0,Pull-down resistor option register 0" line.byte 0x1 "PD1,Pull-down resistor option register 1" line.byte 0x2 "PD2,Pull-down resistor option register 2" line.byte 0x3 "PD3,Pull-down resistor option register 3" group.byte 0x45++0x2 line.byte 0x0 "PD5,Pull-down resistor option register 5" line.byte 0x1 "PD6,Pull-down resistor option register 6" line.byte 0x2 "PD7,Pull-down resistor option register 7" group.byte 0x4C++0x2 line.byte 0x0 "PD12,Pull-down resistor option register 12" line.byte 0x1 "PD13,Pull-down resistor option register 13" line.byte 0x2 "PD14,Pull-down resistor option register 14" group.byte 0x50++0x7 line.byte 0x0 "POM0,Port output mode register 0" line.byte 0x1 "POM1,Port output mode register 1" line.byte 0x2 "POM2,Port output mode register 2" line.byte 0x3 "POM3,Port output mode register 3" line.byte 0x4 "POM4,Port output mode register 4" line.byte 0x5 "POM5,Port output mode register 5" line.byte 0x6 "POM6,Port output mode register 6" line.byte 0x7 "POM7,Port output mode register 7" group.byte 0x5C++0x2 line.byte 0x0 "POM12,Port output mode register 12" line.byte 0x1 "POM13,Port output mode register 13" line.byte 0x2 "POM14,Port output mode register 14" group.byte 0x60++0x3 line.byte 0x0 "PMC0,Port mode control register 0" line.byte 0x1 "PMC1,Port mode control register 1" line.byte 0x2 "PMC2,Port mode control register 2" line.byte 0x3 "PMC3,Port mode control register 3" group.byte 0x65++0x2 line.byte 0x0 "PMC5,Port mode control register 5" line.byte 0x1 "PMC6,Port mode control register 6" line.byte 0x2 "PMC7,Port mode control register 7" group.byte 0x6C++0x2 line.byte 0x0 "PMC12,Port mode control register 12" line.byte 0x1 "PMC13,Port mode control register 13" line.byte 0x2 "PMC14,Port mode control register 14" group.byte 0x10++0x7 line.byte 0x0 "PSET0,Port set register 0" line.byte 0x1 "PSET1,Port set register 1" line.byte 0x2 "PSET2,Port set register 2" line.byte 0x3 "PSET3,Port set register 3" line.byte 0x4 "PSET4,Port set register 4" line.byte 0x5 "PSET5,Port set register 5" line.byte 0x6 "PSET6,Port set register 6" line.byte 0x7 "PSET7,Port set register 7" group.byte 0x1C++0x2 line.byte 0x0 "PSET12,Port set register 12" line.byte 0x1 "PSET13,Port set register 13" line.byte 0x2 "PSET14,Port set register 14" group.byte 0x70++0x7 line.byte 0x0 "PCLR0,Port clear register 0" line.byte 0x1 "PCLR1,Port clear register 1" line.byte 0x2 "PCLR2,Port clear register 2" line.byte 0x3 "PCLR3,Port clear register 3" line.byte 0x4 "PCLR4,Port clear register 4" line.byte 0x5 "PCLR5,Port clear register 5" line.byte 0x6 "PCLR6,Port clear register 6" line.byte 0x7 "PCLR7,Port clear register 7" group.byte 0x7C++0x2 line.byte 0x0 "PCLR12,Port clear register 12" line.byte 0x1 "PCLR13,Port clear register 13" line.byte 0x2 "PCLR14,Port clear register 14" group.byte 0x800++0x1 line.byte 0x0 "P00CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P01CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x808++0x11 line.byte 0x0 "P10CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P11CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x2 "P12CFG,Alterate Output Function configuration register" hexmask.byte 0x2 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x3 "P13CFG,Alterate Output Function configuration register" hexmask.byte 0x3 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x4 "P14CFG,Alterate Output Function configuration register" hexmask.byte 0x4 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x5 "P15CFG,Alterate Output Function configuration register" hexmask.byte 0x5 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x6 "P16CFG,Alterate Output Function configuration register" hexmask.byte 0x6 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x7 "P17CFG,Alterate Output Function configuration register" hexmask.byte 0x7 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x8 "P20CFG,Alterate Output Function configuration register" hexmask.byte 0x8 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x9 "P21CFG,Alterate Output Function configuration register" hexmask.byte 0x9 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xA "P22CFG,Alterate Output Function configuration register" hexmask.byte 0xA 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xB "P23CFG,Alterate Output Function configuration register" hexmask.byte 0xB 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xC "P24CFG,Alterate Output Function configuration register" hexmask.byte 0xC 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xD "P25CFG,Alterate Output Function configuration register" hexmask.byte 0xD 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xE "P26CFG,Alterate Output Function configuration register" hexmask.byte 0xE 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0xF "P27CFG,Alterate Output Function configuration register" hexmask.byte 0xF 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x10 "P30CFG,Alterate Output Function configuration register" hexmask.byte 0x10 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x11 "P31CFG,Alterate Output Function configuration register" hexmask.byte 0x11 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x820++0x1 line.byte 0x0 "P40CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P41CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x828++0x1 line.byte 0x0 "P50CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P51CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x830++0x3 line.byte 0x0 "P60CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P61CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x2 "P62CFG,Alterate Output Function configuration register" hexmask.byte 0x2 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x3 "P63CFG,Alterate Output Function configuration register" hexmask.byte 0x3 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x838++0x5 line.byte 0x0 "P70CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P71CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x2 "P72CFG,Alterate Output Function configuration register" hexmask.byte 0x2 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x3 "P73CFG,Alterate Output Function configuration register" hexmask.byte 0x3 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x4 "P74CFG,Alterate Output Function configuration register" hexmask.byte 0x4 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x5 "P75CFG,Alterate Output Function configuration register" hexmask.byte 0x5 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x840++0x4 line.byte 0x0 "P120CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P121CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x2 "P122CFG,Alterate Output Function configuration register" hexmask.byte 0x2 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x3 "P123CFG,Alterate Output Function configuration register" hexmask.byte 0x3 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x4 "P124CFG,Alterate Output Function configuration register" hexmask.byte 0x4 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x848++0x0 line.byte 0x0 "P130CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x84E++0x2 line.byte 0x0 "P136CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P137CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x2 "P140CFG,Alterate Output Function configuration register" hexmask.byte 0x2 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x856++0x1 line.byte 0x0 "P146CFG,Alterate Output Function configuration register" hexmask.byte 0x0 0.--3. 1. "CFG,Alterate Output Function configuration register" line.byte 0x1 "P147CFG,Alterate Output Function configuration register" hexmask.byte 0x1 0.--3. 1. "CFG,Alterate Output Function configuration register" group.byte 0x860++0x8 line.byte 0x0 "TI10PCFG,TI10 alternate function pin configuration register" hexmask.byte 0x0 0.--5. 1. "CFG" line.byte 0x1 "TI11PCFG,TI11 alternate function pin configuration register" hexmask.byte 0x1 0.--5. 1. "CFG" line.byte 0x2 "TI12PCFG,TI12 alternate function pin configuration register" hexmask.byte 0x2 0.--5. 1. "CFG" line.byte 0x3 "TI13PCFG,TI13 alternate function pin configuration register" hexmask.byte 0x3 0.--5. 1. "CFG" line.byte 0x4 "INTP0PCFG,INTP0 alternate function pin configuration register" hexmask.byte 0x4 0.--5. 1. "CFG" line.byte 0x5 "INTP1PCFG,INTP1 alternate function pin configuration register" hexmask.byte 0x5 0.--5. 1. "CFG" line.byte 0x6 "INTP2PCFG,INTP2 alternate function pin configuration register" hexmask.byte 0x6 0.--5. 1. "CFG" line.byte 0x7 "INTP3PCFG,INTP3 alternate function pin configuration register" hexmask.byte 0x7 0.--5. 1. "CFG" line.byte 0x8 "SDI00PCFG,SDI00/RXD0/SDA00 alternate function pin configuration register" hexmask.byte 0x8 0.--5. 1. "CFG" group.long 0x868++0x3 line.long 0x0 "SDA00PCFG,SDI00/RXD0/SDA00 alternate function pin configuration register" group.long 0x868++0x3 line.long 0x0 "RXD0PCFG,SDI00/RXD0/SDA00 alternate function pin configuration register" group.byte 0x869++0x2 line.byte 0x0 "SCLKI00PCFG,SCLKI00 alternate function pin configuration register" hexmask.byte 0x0 0.--5. 1. "CFG" line.byte 0x1 "SS00PCFG,SS00 alternate function pin configuration register" hexmask.byte 0x1 0.--5. 1. "CFG" line.byte 0x2 "SDI20PCFG,SDI20/RXD2/IrRXD alternate function pin configuration register" hexmask.byte 0x2 0.--5. 1. "CFG" group.byte 0x86B++0x0 line.byte 0x0 "IRRXDPCFG,SDI20/RXD2/IrRXD alternate function pin configuration register" group.byte 0x86B++0x1 line.byte 0x0 "RXD2PCFG,SDI20/RXD2/IrRXD alternate function pin configuration register" line.byte 0x1 "SCLKI20PCFG,SCLKI20 alternate function pin configuration register" hexmask.byte 0x1 0.--5. 1. "CFG" group.byte 0x86F++0x0 line.byte 0x0 "RXD1PCFG,RXD1 alternate function pin configuration register" hexmask.byte 0x0 0.--5. 1. "CFG" group.byte 0x86F++0x0 line.byte 0x0 "SDA10PCFG,SDA10 alternate function pin configuration register" group.byte 0x86F++0x0 line.byte 0x0 "SDI10PCFG,SDI10 alternate function pin configuration register" group.byte 0x86D++0x1 line.byte 0x0 "SDAA0PCFG,SDAA0 alternate function pin configuration register" hexmask.byte 0x0 0.--5. 1. "CFG" line.byte 0x1 "SCLA0PCFG,SCLA0 alternate function pin configuration register" hexmask.byte 0x1 0.--5. 1. "CFG" group.byte 0x87B++0x0 line.byte 0x0 "PMS,Port mode select register" group.byte 0x87E++0x0 line.byte 0x0 "SPIPCFG,SPI alternate function pins configuration register" tree.end tree "RST (Reset Function)" base ad:0x40020420 rgroup.byte 0x20++0x0 line.byte 0x0 "RESF,Reset flag register" bitfld.byte 0x0 7. "SYSRF,Internal reset request by system reset request(AIRCR.SYSRESETREQ)" "0: Internal reset request is not generated or the..,1: Internal reset request is generated." bitfld.byte 0x0 4. "WDTRF,Internal reset request by watchdog timer(WDT)" "0: Internal reset request is not generated or the..,1: Internal reset request is generated." newline bitfld.byte 0x0 2. "RPERF,Internal reset request by RAM parity" "0: Internal reset request is not generated or the..,1: Internal reset request is generated." bitfld.byte 0x0 1. "IAWRF,Internal reset request by illegal-memory access" "0: Internal reset request is not generated or the..,1: Internal reset request is generated." newline bitfld.byte 0x0 0. "LVIRF,Internal reset request by voltage detector" "0: Internal reset request is not generated or the..,1: Internal reset request is generated." tree.end tree "RTC (Real-Time Clock)" base ad:0x40044F00 group.word 0x34++0x1 line.word 0x0 "SUBCUD,Watch error correction register" bitfld.word 0x0 15. "DEV,watch error correction timing" "0,1" hexmask.word 0x0 0.--12. 1. "F,watch error correction value" group.word 0x50++0x1 line.word 0x0 "ITMC,15-bit interval timer control register" bitfld.word 0x0 15. "RINTE,15-bit interval timer operation control" "0,1" hexmask.word 0x0 0.--14. 1. "ITCMP,15-bit interval timer compare value" group.byte 0x52++0x6 line.byte 0x0 "SEC,Second count register" line.byte 0x1 "MIN,Minute count register" line.byte 0x2 "HOUR,Hour count register" line.byte 0x3 "WEEK,Week count register" line.byte 0x4 "DAY,Day count register" line.byte 0x5 "MONTH,Month count register" line.byte 0x6 "YEAR,Year count register" group.byte 0x5A++0x4 line.byte 0x0 "ALARMWM,Alarm minute register" line.byte 0x1 "ALARMWH,Alarm hour register" line.byte 0x2 "ALARMWW,Alarm week register" line.byte 0x3 "RTCC0,Real-time clock control register 0" bitfld.byte 0x3 7. "RTCE,Real-time clock operation control" "0,1" bitfld.byte 0x3 5. "RCLOE,RTC1HZ pin output enable" "0,1" bitfld.byte 0x3 3. "AMPM,Selection of 12-/24-hour system" "0,1" bitfld.byte 0x3 0.--2. "CT,Constant-period interrupt (INTRTC) selection" "0,1,2,3,4,5,6,7" line.byte 0x4 "RTCC1,Real-time clock control register 1" bitfld.byte 0x4 7. "WALE,Alarm operation control" "0,1" bitfld.byte 0x4 6. "WALIE,Control of alarm interrupt (INTRTC) function operation" "0,1" bitfld.byte 0x4 4. "WAFG,Alarm detection status flag" "0,1" bitfld.byte 0x4 3. "RIFG,Constant-period interrupt status flag" "0,1" bitfld.byte 0x4 1. "RWST,Wait status flag of real-time clock" "0,1" bitfld.byte 0x4 0. "RWAIT,Wait control of real-time clock" "0,1" tree.end tree "SAF (High-Speed Cyclic Redundancy Check)" base ad:0x40020100 group.byte 0x1710++0x0 line.byte 0x0 "CRC0CTL,Flash memory CRC control register" bitfld.byte 0x0 7. "CRC0EN,Control of high-speed CRC operation" "0,1" hexmask.byte 0x0 0.--6. 1. "FEA,High-speed CRC operation range" group.word 0x1712++0x1 line.word 0x0 "PGCRCL,Flash memory CRC operation result register" group.byte 0x232AC++0x0 line.byte 0x0 "CRCIN,CRC input register" group.word 0x231FA++0x1 line.word 0x0 "CRCD,CRC data register" group.byte 0x325++0x0 line.byte 0x0 "RPECTL,RAM parity error control register" bitfld.byte 0x0 7. "RPERDIS,Disable RAM parity error reset" "0: Enable parity error reset,1: Disable parity error reset" bitfld.byte 0x0 0. "RPEF,Parity error status flag" "0: No parity error has occurred,1: Parity error has occurred" group.long 0x20378++0x3 line.long 0x0 "SFRGD,SFR guard control register" tree.end tree "SCI (Serial Communication Interface)" base ad:0x0 rgroup.word 0x0++0x7 line.word 0x0 "SSR00,Serial status register mn" bitfld.word 0x0 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x0 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x0 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x0 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x0 0. "OVF,Overrun error detection flag of channel n" "0,1" line.word 0x2 "SSR01,Serial status register mn" bitfld.word 0x2 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x2 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x2 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x2 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x2 0. "OVF,Overrun error detection flag of channel n" "0,1" line.word 0x4 "SSR02,Serial status register mn" bitfld.word 0x4 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x4 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x4 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x4 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x4 0. "OVF,Overrun error detection flag of channel n" "0,1" line.word 0x6 "SSR03,Serial status register mn" bitfld.word 0x6 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x6 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x6 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x6 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x6 0. "OVF,Overrun error detection flag of channel n" "0,1" group.word 0x8++0x17 line.word 0x0 "SIR00,Serial flag clear trigger register mn" bitfld.word 0x0 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x0 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x0 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" line.word 0x2 "SIR01,Serial flag clear trigger register mn" bitfld.word 0x2 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x2 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x2 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" line.word 0x4 "SIR02,Serial flag clear trigger register mn" bitfld.word 0x4 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x4 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x4 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" line.word 0x6 "SIR03,Serial flag clear trigger register mn" bitfld.word 0x6 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x6 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x6 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" line.word 0x8 "SMR00,Serial mode register mn" bitfld.word 0x8 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0x8 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0x8 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0x8 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0x8 0.--3. 1. "MD,Setting of operation mode of channel n" line.word 0xA "SMR01,Serial mode register mn" bitfld.word 0xA 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0xA 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0xA 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0xA 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0xA 0.--3. 1. "MD,Setting of operation mode of channel n" line.word 0xC "SMR02,Serial mode register mn" bitfld.word 0xC 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0xC 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0xC 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0xC 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0xC 0.--3. 1. "MD,Setting of operation mode of channel n" line.word 0xE "SMR03,Serial mode register mn" bitfld.word 0xE 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0xE 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0xE 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0xE 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0xE 0.--3. 1. "MD,Setting of operation mode of channel n" line.word 0x10 "SCR00,Serial communication operation setting register mn" bitfld.word 0x10 15. "TXE,Transmission enable" "0,1" bitfld.word 0x10 14. "RXE,Reception enable" "0,1" bitfld.word 0x10 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x10 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x10 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x10 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x10 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x10 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x10 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" line.word 0x12 "SCR01,Serial communication operation setting register mn" bitfld.word 0x12 15. "TXE,Transmission enable" "0,1" bitfld.word 0x12 14. "RXE,Reception enable" "0,1" bitfld.word 0x12 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x12 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x12 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x12 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x12 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x12 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x12 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" line.word 0x14 "SCR02,Serial communication operation setting register mn" bitfld.word 0x14 15. "TXE,Transmission enable" "0,1" bitfld.word 0x14 14. "RXE,Reception enable" "0,1" bitfld.word 0x14 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x14 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x14 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x14 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x14 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x14 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x14 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" line.word 0x16 "SCR03,Serial communication operation setting register mn" bitfld.word 0x16 15. "TXE,Transmission enable" "0,1" bitfld.word 0x16 14. "RXE,Reception enable" "0,1" bitfld.word 0x16 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x16 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x16 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x16 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x16 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x16 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x16 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" rgroup.word 0x20++0x1 line.word 0x0 "SE0,Serial channel enable status register m" bitfld.word 0x0 3. "SE03,Indication of operation enable/stop status of channel 3" "0,1" bitfld.word 0x0 2. "SE02,Indication of operation enable/stop status of channel 2" "0,1" bitfld.word 0x0 1. "SE01,Indication of operation enable/stop status of channel 1" "0,1" bitfld.word 0x0 0. "SE00,Indication of operation enable/stop status of channel 0" "0,1" group.word 0x22++0x9 line.word 0x0 "SS0,Serial channel start register 0" bitfld.word 0x0 3. "SS03,Operation start trigger of channel 3" "0,1" bitfld.word 0x0 2. "SS02,Operation start trigger of channel 2" "0,1" bitfld.word 0x0 1. "SS01,Operation start trigger of channel 1" "0,1" bitfld.word 0x0 0. "SS00,Operation start trigger of channel 0" "0,1" line.word 0x2 "ST0,Serial channel stop register 0" bitfld.word 0x2 3. "ST03,Operation stop trigger of channel 3" "0,1" bitfld.word 0x2 2. "ST02,Operation stop trigger of channel 2" "0,1" bitfld.word 0x2 1. "ST01,Operation stop trigger of channel 1" "0,1" bitfld.word 0x2 0. "ST00,Operation stop trigger of channel 0" "0,1" line.word 0x4 "SPS0,Serial clock select register 0" hexmask.word.byte 0x4 4.--7. 1. "PRS01,Prescaler 1" hexmask.word.byte 0x4 0.--3. 1. "PRS00,Prescaler 0" line.word 0x6 "SO0,Serial output register 0" bitfld.word 0x6 11. "CKO03,Serial clock output of channel 3" "0,1" bitfld.word 0x6 10. "CKO02,Serial clock output of channel 2" "0,1" bitfld.word 0x6 9. "CKO01,Serial clock output of channel 1" "0,1" bitfld.word 0x6 8. "CKO00,Serial clock output of channel 0" "0,1" bitfld.word 0x6 3. "SO03,Serial data output of channel 3" "0,1" bitfld.word 0x6 2. "SO02,Serial data output of channel 2" "0,1" bitfld.word 0x6 1. "SO01,Serial data output of channel 1" "0,1" bitfld.word 0x6 0. "SO00,Serial data output of channel 0" "0,1" line.word 0x8 "SOE0,Serial output enable register 0" bitfld.word 0x8 3. "SOE03,Serial output enable of channel 3" "0,1" bitfld.word 0x8 2. "SOE02,Serial output enable of channel 2" "0,1" bitfld.word 0x8 1. "SOE01,Serial output enable of channel 1" "0,1" bitfld.word 0x8 0. "SOE00,Serial output enable of channel 0" "0,1" group.word 0x34++0x1 line.word 0x0 "SOL0,Serial output level register 0" bitfld.word 0x0 2. "SOL02,Selects inversion of the level of the transmit data of channel n in UART mode" "0,1" bitfld.word 0x0 0. "SOL00,Selects inversion of the level of the transmit data of channel n in UART mode" "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x210)++0x1 line.word 0x0 "SDR0$1,Serial data register 0%s" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x244)++0x1 line.word 0x0 "SDR0$1,Serial data register 0%s" repeat.end group.byte 0x210++0x0 line.byte 0x0 "SIO00,SPI data register" group.byte 0x212++0x0 line.byte 0x0 "SIO01,SPI data register" group.byte 0x244++0x0 line.byte 0x0 "SIO10,SPI data register" group.byte 0x246++0x0 line.byte 0x0 "SIO11,SPI data register" group.byte 0x210++0x0 line.byte 0x0 "TXD0,UART transmit data register" group.byte 0x212++0x0 line.byte 0x0 "RXD0,UART receive data register" group.byte 0x244++0x0 line.byte 0x0 "TXD1,UART transmit data register" group.byte 0x246++0x0 line.byte 0x0 "RXD1,UART receive data register" rgroup.word 0x0++0x3 line.word 0x0 "SSR10,Serial status register mn" bitfld.word 0x0 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x0 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x0 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x0 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x0 0. "OVF,Overrun error detection flag of channel n" "0,1" line.word 0x2 "SSR11,Serial status register mn" bitfld.word 0x2 6. "TSF,Communication status indication flag of channel n" "0,1" bitfld.word 0x2 5. "BFF,Buffer register status indication flag of channel n" "0,1" bitfld.word 0x2 2. "FEF,Framing error detection flag of channel n" "0,1" bitfld.word 0x2 1. "PEF,Parity error detection flag of channel n" "0,1" bitfld.word 0x2 0. "OVF,Overrun error detection flag of channel n" "0,1" group.word 0x8++0x3 line.word 0x0 "SIR10,Serial flag clear trigger register mn" bitfld.word 0x0 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x0 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x0 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" line.word 0x2 "SIR11,Serial flag clear trigger register mn" bitfld.word 0x2 2. "FECT,Clear trigger of framing error flag of channel n" "0,1" bitfld.word 0x2 1. "PECT,Clear trigger of parity error flag of channel n" "0,1" bitfld.word 0x2 0. "OVCT,Clear trigger of overrun error flag of channel n" "0,1" group.word 0x10++0x3 line.word 0x0 "SMR10,Serial mode register mn" bitfld.word 0x0 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0x0 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0x0 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0x0 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0x0 0.--3. 1. "MD,Setting of operation mode of channel n" line.word 0x2 "SMR11,Serial mode register mn" bitfld.word 0x2 15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1" bitfld.word 0x2 14. "CCS,Selection of transfer clock (fTCLK) of channel n" "0,1" bitfld.word 0x2 8. "STS,Selection of start trigger source" "0,1" bitfld.word 0x2 6. "SIS,Controls inversion of level of receive data of channel n in UART mode" "0,1" hexmask.word.byte 0x2 0.--3. 1. "MD,Setting of operation mode of channel n" group.word 0x18++0x3 line.word 0x0 "SCR10,Serial communication operation setting register mn" bitfld.word 0x0 15. "TXE,Transmission enable" "0,1" bitfld.word 0x0 14. "RXE,Reception enable" "0,1" bitfld.word 0x0 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x0 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x0 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x0 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x0 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x0 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x0 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" line.word 0x2 "SCR11,Serial communication operation setting register mn" bitfld.word 0x2 15. "TXE,Transmission enable" "0,1" bitfld.word 0x2 14. "RXE,Reception enable" "0,1" bitfld.word 0x2 13. "DAP,Selection of data phase in SPI mode" "0,1" bitfld.word 0x2 12. "CKP,Selection of clock phase in SPI mode" "0,1" bitfld.word 0x2 10. "EOC,Mask control of error interrupt signal (INTSREx (x = 0 to 2))" "0,1" bitfld.word 0x2 8.--9. "PTC,Setting of parity bit in UART mode" "0,1,2,3" bitfld.word 0x2 7. "DIR,Selection of data transfer sequence in SPI and UART modes" "0,1" bitfld.word 0x2 4.--5. "SLC,Setting of stop bit in UART mode" "0,1,2,3" bitfld.word 0x2 0.--1. "DLS,Setting of data length in SPI and UART modes" "0,1,2,3" rgroup.word 0x20++0x1 line.word 0x0 "SE1,Serial channel enable status register 1" bitfld.word 0x0 1. "SE11,Indication of operation enable/stop status of channel 1" "0,1" bitfld.word 0x0 0. "SE10,Indication of operation enable/stop status of channel 0" "0,1" group.word 0x22++0x9 line.word 0x0 "SS1,Serial channel start register 1" bitfld.word 0x0 1. "SS11,Operation start trigger of channel 1" "0,1" bitfld.word 0x0 0. "SS10,Operation start trigger of channel 0" "0,1" line.word 0x2 "ST1,Serial channel stop register 1" bitfld.word 0x2 1. "ST11,Operation stop trigger of channel 1" "0,1" bitfld.word 0x2 0. "ST10,Operation stop trigger of channel 0" "0,1" line.word 0x4 "SPS1,Serial clock select register 1" hexmask.word.byte 0x4 4.--7. 1. "PRS11,Prescaler 1" hexmask.word.byte 0x4 0.--3. 1. "PRS10,Prescaler 0" line.word 0x6 "SO1,Serial output register 1" bitfld.word 0x6 9. "CKO11,Serial clock output of channel 1" "0,1" bitfld.word 0x6 8. "CKO10,Serial clock output of channel 0" "0,1" bitfld.word 0x6 1. "SO11,Serial data output of channel 1" "0,1" bitfld.word 0x6 0. "SO10,Serial data output of channel 0" "0,1" line.word 0x8 "SOE1,Serial output enable register 1" bitfld.word 0x8 1. "SOE11,Serial output enable of channel 1" "0,1" bitfld.word 0x8 0. "SOE10,Serial output enable of channel 0" "0,1" group.word 0x34++0x1 line.word 0x0 "SOL1,Serial output level register 1" bitfld.word 0x0 0. "SOL10,Selects inversion of the level of the transmit data of channel n in UART mode" "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x208)++0x1 line.word 0x0 "SDR1$1,Serial data register 1%s" repeat.end group.byte 0x208++0x0 line.byte 0x0 "SIO20,SPI data register" group.byte 0x20A++0x0 line.byte 0x0 "SIO21,SPI data register" group.byte 0x208++0x0 line.byte 0x0 "TXD2,UART transmit data register" group.byte 0x20A++0x0 line.byte 0x0 "RXD2,UART receive data register" tree.end tree "SPI (Serial Peripheral Interface)" base ad:0x40042400 group.long 0x0++0xF line.long 0x0 "SPIM,SPI mode control register" bitfld.long 0x0 7. "SPIE,SPI operation enable" "0,1" bitfld.long 0x0 6. "TRMD,Transfer and Receive mode" "0,1" bitfld.long 0x0 5. "NSSE,NSS pin enable" "0,1" bitfld.long 0x0 4. "DIR,MSB of LSB mode select" "0,1" bitfld.long 0x0 3. "INTMD,interrupt source select" "0,1" bitfld.long 0x0 2. "DLS,data length control" "0,1" bitfld.long 0x0 1. "SDRIF,Receive buffer non-empty flag" "0,1" bitfld.long 0x0 0. "SPTF,SPI transmission status flag" "0,1" line.long 0x4 "SPIC,SPI control register" bitfld.long 0x4 4. "CKP,Selection of clock phase for SPI" "0,1" bitfld.long 0x4 3. "DAP,Selection of data phase for SPI" "0,1" bitfld.long 0x4 0.--2. "CKS,Operation clock control" "0,1,2,3,4,5,6,7" line.long 0x8 "SDRO,Data buffer of transmission" line.long 0xC "SDRI,Data buffer of reception" tree.end tree "TM (General Purpose Timer 4)" base ad:0x0 tree "TM40" base ad:0x40041D80 repeat 4. (increment 0x0 0x1)(increment 0x0 0x2) rgroup.word ($2)++0x1 line.word 0x0 "TCR0$1,Timer count register 0%s" repeat.end group.word 0x10++0x7 line.word 0x0 "TMR00,Timer mode register mn" bitfld.word 0x0 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x0 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x0 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x0 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x0 0.--3. 1. "MD,Operation mode of channel n" line.word 0x2 "TMR01,Timer mode register mn" bitfld.word 0x2 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x2 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x2 11. "SPLIT,Selection of 8 or 16-bit timer operation for channels 1 and 3" "0,1" bitfld.word 0x2 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x2 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x2 0.--3. 1. "MD,Operation mode of channel n" line.word 0x4 "TMR02,Timer mode register mn" bitfld.word 0x4 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x4 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x4 11. "MASTER,Selection between using channel n independently or simultaneously with another channel (as a slave or master)" "0,1" bitfld.word 0x4 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x4 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x4 0.--3. 1. "MD,Operation mode of channel n" line.word 0x6 "TMR03,Timer mode register mn" bitfld.word 0x6 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x6 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x6 11. "SPLIT,Selection of 8 or 16-bit timer operation for channels 1 and 3" "0,1" bitfld.word 0x6 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x6 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x6 0.--3. 1. "MD,Operation mode of channel n" rgroup.word 0x20++0x7 line.word 0x0 "TSR00,Timer status register mn" bitfld.word 0x0 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x2 "TSR01,Timer status register mn" bitfld.word 0x2 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x4 "TSR02,Timer status register mn" bitfld.word 0x4 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x6 "TSR03,Timer status register mn" bitfld.word 0x6 0. "OVF,Counter overflow status of channel n" "0,1" rgroup.word 0x30++0x1 line.word 0x0 "TE0,Timer channel enable status register m" bitfld.word 0x0 11. "TEH03,Indication of whether operation of the higher 8-bit timer is enabled or stopped when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 9. "TEH01,Indication of whether operation of the higher 8-bit timer is enabled or stopped when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 3. "TE03,Indication of operation enable/stop status of channel 3" "0,1" bitfld.word 0x0 2. "TE02,Indication of operation enable/stop status of channel 2" "0,1" bitfld.word 0x0 1. "TE01,Indication of operation enable/stop status of channel 1" "0,1" bitfld.word 0x0 0. "TE00,Indication of operation enable/stop status of channel 0" "0,1" group.word 0x32++0xD line.word 0x0 "TS0,Timer channel start register 0" bitfld.word 0x0 11. "TSH03,Trigger to enable operation (start operation) of the higher 8-bit timer when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 9. "TSH01,Trigger to enable operation (start operation) of the higher 8-bit timer when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 3. "TS03,Operation enable (start) trigger of channel 3" "0,1" bitfld.word 0x0 2. "TS02,Operation enable (start) trigger of channel 2" "0,1" bitfld.word 0x0 1. "TS01,Operation enable (start) trigger of channel 1" "0,1" bitfld.word 0x0 0. "TS00,Operation enable (start) trigger of channel 0" "0,1" line.word 0x2 "TT0,Timer channel stop register 0" bitfld.word 0x2 11. "TTH03,Trigger to stop operation of the higher 8-bit timer when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x2 9. "TTH01,Trigger to stop operation of the higher 8-bit timer when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x2 3. "TT03,Operation stop trigger of channel 3" "0,1" bitfld.word 0x2 2. "TT02,Operation stop trigger of channel 2" "0,1" bitfld.word 0x2 1. "TT01,Operation stop trigger of channel 1" "0,1" bitfld.word 0x2 0. "TT00,Operation stop trigger of channel 0" "0,1" line.word 0x4 "TPS0,Timer clock select register 0" bitfld.word 0x4 12.--13. "PRS03,Prescaler 3" "0,1,2,3" bitfld.word 0x4 8.--9. "PRS02,Prescaler 2" "0,1,2,3" hexmask.word.byte 0x4 4.--7. 1. "PRS01,Prescaler 1" hexmask.word.byte 0x4 0.--3. 1. "PRS00,Prescaler 0" line.word 0x6 "TO0,Timer output register 0" bitfld.word 0x6 3. "TO03,Timer output of channel 3" "0,1" bitfld.word 0x6 2. "TO02,Timer output of channel 2" "0,1" bitfld.word 0x6 1. "TO01,Timer output of channel 1" "0,1" bitfld.word 0x6 0. "TO00,Timer output of channel 0" "0,1" line.word 0x8 "TOE0,Timer output enable register 0" bitfld.word 0x8 3. "TOE03,Timer output enable of channel 3" "0,1" bitfld.word 0x8 2. "TOE02,Timer output enable of channel 2" "0,1" bitfld.word 0x8 1. "TOE01,Timer output enable of channel 1" "0,1" bitfld.word 0x8 0. "TOE00,Timer output enable of channel 0" "0,1" line.word 0xA "TOL0,Timer output level register 0" bitfld.word 0xA 3. "TOL03,Control of timer output level of channel 3" "0,1" bitfld.word 0xA 2. "TOL02,Control of timer output level of channel 2" "0,1" bitfld.word 0xA 1. "TOL01,Control of timer output level of channel 1" "0,1" line.word 0xC "TOM0,Timer output mode register 0" bitfld.word 0xC 3. "TOM03,Control of timer output mode of channel 3" "0,1" bitfld.word 0xC 2. "TOM02,Control of timer output mode of channel 2" "0,1" bitfld.word 0xC 1. "TOM01,Control of timer output mode of channel 1" "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x198)++0x1 line.word 0x0 "TDR0$1,Timer data register 0%s" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x1E4)++0x1 line.word 0x0 "TDR0$1,Timer data register 0%s" repeat.end group.byte 0x19A++0x1 line.byte 0x0 "TDR01L,Timer data lower register 01" line.byte 0x1 "TDR01H,Timer data higher register 01" group.byte 0x1E6++0x1 line.byte 0x0 "TDR03L,Timer data lower register 03" line.byte 0x1 "TDR03H,Timer data higher register 03" tree.end tree "TM41" base ad:0x40042180 repeat 4. (increment 0x0 0x1)(increment 0x0 0x2) rgroup.word ($2)++0x1 line.word 0x0 "TCR1$1,Timer count register 0%s" repeat.end group.word 0x10++0x7 line.word 0x0 "TMR10,Timer mode register mn" bitfld.word 0x0 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x0 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x0 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x0 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x0 0.--3. 1. "MD,Operation mode of channel n" line.word 0x2 "TMR11,Timer mode register mn" bitfld.word 0x2 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x2 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x2 11. "SPLIT,Selection of 8 or 16-bit timer operation for channels 1 and 3" "0,1" bitfld.word 0x2 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x2 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x2 0.--3. 1. "MD,Operation mode of channel n" line.word 0x4 "TMR12,Timer mode register mn" bitfld.word 0x4 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x4 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x4 11. "MASTER,Selection between using channel n independently or simultaneously with another channel (as a slave or master)" "0,1" bitfld.word 0x4 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x4 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x4 0.--3. 1. "MD,Operation mode of channel n" line.word 0x6 "TMR13,Timer mode register mn" bitfld.word 0x6 14.--15. "CKS,Selection of operation clock (fMCK) of channel n" "0,1,2,3" bitfld.word 0x6 12. "CCS,Selection of count clock (fTCLK) of channel n" "0,1" bitfld.word 0x6 11. "SPLIT,Selection of 8 or 16-bit timer operation for channels 1 and 3" "0,1" bitfld.word 0x6 8.--10. "STS,Setting of start trigger or capture trigger of channel n" "0,1,2,3,4,5,6,7" bitfld.word 0x6 6.--7. "CIS,Selection of TImn pin input valid edge" "0,1,2,3" hexmask.word.byte 0x6 0.--3. 1. "MD,Operation mode of channel n" rgroup.word 0x20++0x7 line.word 0x0 "TSR10,Timer status register mn" bitfld.word 0x0 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x2 "TSR11,Timer status register mn" bitfld.word 0x2 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x4 "TSR12,Timer status register mn" bitfld.word 0x4 0. "OVF,Counter overflow status of channel n" "0,1" line.word 0x6 "TSR13,Timer status register mn" bitfld.word 0x6 0. "OVF,Counter overflow status of channel n" "0,1" rgroup.word 0x30++0x1 line.word 0x0 "TE1,Timer channel enable status register m" bitfld.word 0x0 11. "TEH13,Indication of whether operation of the higher 8-bit timer is enabled or stopped when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 9. "TEH11,Indication of whether operation of the higher 8-bit timer is enabled or stopped when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 3. "TE13,Indication of operation enable/stop status of channel 3" "0,1" bitfld.word 0x0 2. "TE12,Indication of operation enable/stop status of channel 2" "0,1" bitfld.word 0x0 1. "TE11,Indication of operation enable/stop status of channel 1" "0,1" bitfld.word 0x0 0. "TE10,Indication of operation enable/stop status of channel 0" "0,1" group.word 0x32++0xD line.word 0x0 "TS1,Timer channel start register 0" bitfld.word 0x0 11. "TSH13,Trigger to enable operation (start operation) of the higher 8-bit timer when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 9. "TSH11,Trigger to enable operation (start operation) of the higher 8-bit timer when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x0 3. "TS13,Operation enable (start) trigger of channel 3" "0,1" bitfld.word 0x0 2. "TS12,Operation enable (start) trigger of channel 2" "0,1" bitfld.word 0x0 1. "TS11,Operation enable (start) trigger of channel 1" "0,1" bitfld.word 0x0 0. "TS10,Operation enable (start) trigger of channel 0" "0,1" line.word 0x2 "TT1,Timer channel stop register 0" bitfld.word 0x2 11. "TTH13,Trigger to stop operation of the higher 8-bit timer when channel 3 is in the 8-bit timer mode" "0,1" bitfld.word 0x2 9. "TTH11,Trigger to stop operation of the higher 8-bit timer when channel 1 is in the 8-bit timer mode" "0,1" bitfld.word 0x2 3. "TT13,Operation stop trigger of channel 3" "0,1" bitfld.word 0x2 2. "TT12,Operation stop trigger of channel 2" "0,1" bitfld.word 0x2 1. "TT11,Operation stop trigger of channel 1" "0,1" bitfld.word 0x2 0. "TT10,Operation stop trigger of channel 0" "0,1" line.word 0x4 "TPS1,Timer clock select register 0" bitfld.word 0x4 12.--13. "PRS13,Prescaler 3" "0,1,2,3" bitfld.word 0x4 8.--9. "PRS12,Prescaler 2" "0,1,2,3" hexmask.word.byte 0x4 4.--7. 1. "PRS11,Prescaler 1" hexmask.word.byte 0x4 0.--3. 1. "PRS10,Prescaler 0" line.word 0x6 "TO1,Timer output register 0" bitfld.word 0x6 3. "TO13,Timer output of channel 3" "0,1" bitfld.word 0x6 2. "TO12,Timer output of channel 2" "0,1" bitfld.word 0x6 1. "TO11,Timer output of channel 1" "0,1" bitfld.word 0x6 0. "TO10,Timer output of channel 0" "0,1" line.word 0x8 "TOE1,Timer output enable register 0" bitfld.word 0x8 3. "TOE13,Timer output enable of channel 3" "0,1" bitfld.word 0x8 2. "TOE12,Timer output enable of channel 2" "0,1" bitfld.word 0x8 1. "TOE11,Timer output enable of channel 1" "0,1" bitfld.word 0x8 0. "TOE10,Timer output enable of channel 0" "0,1" line.word 0xA "TOL1,Timer output level register 0" bitfld.word 0xA 3. "TOL13,Control of timer output level of channel 3" "0,1" bitfld.word 0xA 2. "TOL12,Control of timer output level of channel 2" "0,1" bitfld.word 0xA 1. "TOL11,Control of timer output level of channel 1" "0,1" line.word 0xC "TOM1,Timer output mode register 0" bitfld.word 0xC 3. "TOM13,Control of timer output mode of channel 3" "0,1" bitfld.word 0xC 2. "TOM12,Control of timer output mode of channel 2" "0,1" bitfld.word 0xC 1. "TOM11,Control of timer output mode of channel 1" "0,1" repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x198)++0x1 line.word 0x0 "TDR1$1,Timer data register 0%s" repeat.end repeat 2. (increment 0x0 0x1)(increment 0x0 0x2) group.word ($2+0x1E4)++0x1 line.word 0x0 "TDR1$1,Timer data register 0%s" repeat.end group.byte 0x19A++0x1 line.byte 0x0 "TDR11L,Timer data lower register 01" line.byte 0x1 "TDR11H,Timer data higher register 01" group.byte 0x1E6++0x1 line.byte 0x0 "TDR13L,Timer data lower register 03" line.byte 0x1 "TDR13H,Timer data higher register 03" tree.end tree.end tree "TSN (Temperature Sensor Calibration Data)" base ad:0x500668 rgroup.long 0x0++0x7 line.long 0x0 "TSN85,The A/D conversion value of Temperature Sensor at 85 degrees and 3.0V reference voltage" line.long 0x4 "TSN25,The A/D conversion value of Temperature Sensor at 25 degrees and 3.0V reference voltage" tree.end tree "UID (128-bit Unique ID)" base ad:0x500894 repeat 4. (increment 0x0 0x1)(increment 0x0 0x4) rgroup.long ($2)++0x3 line.long 0x0 "UID$1,UID word %s" repeat.end tree.end tree "WDT (Watchdog Timer)" base ad:0x40020404 group.byte 0x1++0x1 line.byte 0x0 "LOCKCTL,Lockup Watchdog timer enable register" line.byte 0x1 "PRCR,Lockup Watchdog timer enable protect register" group.byte 0xBFD++0x0 line.byte 0x0 "WDTE,Watchdog timer enable register" tree.end newline AUTOINDENT.OFF