Gen4_R-Car_Trace32/2_Trunk/demo/arm/flash/stm32f7xx-qspi.cmm

; --------------------------------------------------------------------------------
; @Title: Flash declaration for ST STM32F7xx QSPI flash program (Memory Mapped)
; @Description:
;   Script arguments:
;
;    DO stm32f7xx-qspi [PREPAREONLY] [CPU=<cpu>] [DUALPORT=0|1]
;
;      PREPAREONLY only declares flash but does not execute flash programming
;
;      CPU=<cpu> selects CPU derivative <cpu>
;
;      DUALPORT=0|1 default value is 0 (disabled).
;
;   Example:
;
;   DO ~~/demo/arm/flash/stm32f7xx-qspi CPU=STM32F756NG PREPAREONLY DUALPORT=1
;
; @Author: JIM
; @Chip: STM32F72* STM32F73* STM32F74* STM32F75* STM32F76* STM32F77*
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
; --------------------------------------------------------------------------------
; $Rev: 10516 $
; $Id: stm32f7xx-qspi.cmm 10516 2022-02-02 11:39:30Z bschroefel $

&QSPI_BASE=0xA0001000

PRIVATE &parameters
ENTRY %LINE &parameters

PRIVATE &param_prepareonly &param_cpu &param_dualport
&param_prepareonly=(STRing.SCAN(STRing.UPpeR("&parameters"),"PREPAREONLY",0)!=-1)
&param_cpu=STRing.SCANAndExtract(STRing.UPpeR("&parameters"),"CPU=","")
&param_dualport=STRing.SCANAndExtract(STRing.UPpeR("&parameters"),"DUALPORT=","0")

; ------------------------------------------------------------------------------
; Setup CPU

DO ~~/demo/arm/flash/stm32f7xx PREPAREONLY CPU=&param_cpu DUALPORT=&param_dualport

; ------------------------------------------------------------------------------
; Flash Power & Clock Enable
Data.Set A:0x40023838 %LE %Long 0x2   ; RCC_AHB3ENR, Quad SPI memory controller clock enable

Data.Set A:0x40023818 %LE %Long 0x2   ; RCC_AHB3RSTR, Quad SPI memory controller reset
Data.Set A:0x40023818 %LE %Long 0x0   ; RCC_AHB3RSTR, release Quad SPI memory controller reset
Data.Set A:0x40023858 %LE %Long 0x2   ; RCC_AHB3LPENR, QUADSPI memory controller clock enable during Sleep mode

Data.Set A:0x40023830 %LE %Long 0x0010003A  ;GPIOB & GPIOD & GPIOE & GPIOF clk enable

; ------------------------------------------------------------------------------
; Flash Pin Mux Configuration
GOSUB PINMUX_CONFIG

; ------------------------------------------------------------------------------
; Flash Controller Init
Data.Set A:&QSPI_BASE+0x0000  %Long 0x04000311    ; QUADSPI_CR, QUADSPI control register, enable clk and prescaler (/4)
Data.Set A:&QSPI_BASE+0x0004  %Long 0x00190100    ; QUADSPI_DCR, flash size 2^26 (64MBytes), 0x00170100==16Mbytes
Data.Set A:&QSPI_BASE+0x000C  %Long 0xFF          ; QUADSPI_FCR, QUADSPI flag clear register

//EXIT QUAD INPUT/OUTPUT MODE, to make the single spi mode
GOSUB WRITEBYTE_QPI   0xF5

GOSUB READ_ID_TEST

//switch QSPI to the memory mapped mode
Data.Set  A:&QSPI_BASE      %Long  (Data.Long(A:&QSPI_BASE)&~0x1)  ;disable
Data.Set  A:&QSPI_BASE+0x14 %Long  0x0D002503   ; FMODE, READ cmd(0x03), ADSize 24b and so on...
Data.Set  A:&QSPI_BASE      %Long  (Data.Long(A:&QSPI_BASE)|0x1)  ;enable

; ------------------------------------------------------------------------------
; Flash declaration
GOSUB FlashDeclaration "&param_dualport"

; Flash script ends here if called with parameter PREPAREONLY
IF &param_prepareonly
  ENDDO PREPAREDONE

; -------------------------------------------------------------------------------
; Flash programming example

DIALOG.YESNO "Program flash memory?"
LOCAL &progflash
ENTRY &progflash
IF &progflash
(
  FLASH.ReProgram.ALL
  Data.LOAD.auto *
  FLASH.ReProgram.off

  ; Reset device
  SYStem.Down
  SYStem.Up
)

ENDDO


PINMUX_CONFIG:
(

//pin mux,  please refer the STM32F756xx alternate function mapping (Pinouts and pin description)
;C <-> GPIOB[2] en ALT 9,    (QUADSPI_CLK)
;S# <-> GPIOB[6] en ALT 10,  (QUADSPI_BK1_NCS)
;DQ0 <-> GPIOF[8] en ALT 10, (QUADSPI_BK1_IO0)
;DQ1 <-> GPIOF[9] en ALT 10, (QUADSPI_BK1_IO1)
;DQ2 <-> GPIOF[7] en ALT 9,  (QUADSPI_BK1_IO2)
;DQ3 <-> GPIOF[6] en ALT 9.  (QUADSPI_BK1_IO3)

Data.Set A:0x40020400 %LE %Long 0x000022A0 ;GPIOB_MODER
Data.Set A:0x40020420 %LE %Long 0x0A000900 ;PB6 alt 10, PB2 alt 9
Data.Set A:0x40020424 %LE %Long 0x00000000 ;

//PD11 & PD12 alt9
//Data.Set A:0x40020C00 %LE %Long 0x02800000   ; GPIOD_MODER
//Data.Set A:0x40020C24 %LE %Long 0x00099000   ; PD11 & PD12 alt 9.

Data.Set A:0x40021400 %LE %Long 0x000AA000   ; GPIOF_MODER
Data.Set A:0x40021420 %LE %Long 0x99000000   ; PF7 & PF6 alt 9.
Data.Set A:0x40021424 %LE %Long 0x000000AA   ; PF8 & PF9 alt 10.

RETURN
)

READ_ID_TEST:
(
&QSPI_FCR=&QSPI_BASE+0xC
&QSPI_CCR=&QSPI_BASE+0x14
&QSPI_DLR=&QSPI_BASE+0x10
&QSPI_DR=&QSPI_BASE+0x20

Data.Set A:&QSPI_FCR %LE %Long 0x1F  ;clear status

// 1 instruction , 4 read data
Data.Set A:&QSPI_DLR  %Long 0x3  ; 4byte data read

&ccr=0x19F             ; imode with instruction  1byte instruction write
&ccr=&ccr|(0x1<<24.)   ; dmode single
&ccr=&ccr|(0x1<<26.)   ; indirect read mode
Data.Set A:&QSPI_CCR %LE %Long &ccr

&read_data=Data.Long(A:&QSPI_DR)  ;read little endian

PRINT "1st 0x" &read_data&0xFF        " (Manufacturer)"
PRINT "2nd 0x" (&read_data>>8.)&0xFF  " (Device ID)"
PRINT "3rd 0x" (&read_data>>16.)&0xFF 
PRINT "4th 0x" (&read_data>>24.)&0xFF 

RETURN
)


WRITEBYTE_QPI:
(
ENTRY &wdata

SCREEN.OFF

Data.Set A:(&QSPI_BASE+0xC) %LE %Long 0x1F  ;clear status

&ccr=(0x3<<8)|&wdata       ; imode with instruction  1byte instruction write
Data.Set A:(&QSPI_BASE+0x14) %LE %Long &ccr

SCREEN.ON

RETURN 
)

; Flash declaration

FlashDeclaration:
(
  PRIVATE &FlashSize &FlashDriver  &FlashBaseAddr
  PARAMETERS &DualPort

  &FlashDriver="snor3b_stm32f7.bin"
  &FlashSize=0x400000        ;4Mbytes
  &FlashBaseAddr=0x90000000  ;SPI AHB base address
  
   FLASH.Create  2. &FlashBaseAddr++(&FlashSize-0x1)    0x10000   TARGET2   Byte

  IF "&DualPort"=="0"
    FLASH.TARGET2 0x20000000 0x20002000 0x4000 ~~/demo/arm/flash/byte/&FlashDriver
  ELSE
    FLASH.TARGET2 0x20000000 EAHB:0x20002000 0x4000 ~~/demo/arm/flash/byte/&FlashDriver /DualPort

  FLASH.List

  RETURN
)