19457 lines
1.3 MiB
19457 lines
1.3 MiB
; --------------------------------------------------------------------------------
|
|
; @Title: TLE989x On-Chip Peripherals
|
|
; @Props: Released
|
|
; @Author: ADR, JON, NEJ
|
|
; @Changelog: 2021-12-15 ADR
|
|
; 2023-11-16 NEJ
|
|
; @Manufacturer: INFINEON - Infineon Technologies AG
|
|
; @Doc: Generated (TRACE32, build: 164232.), based on:
|
|
; tle989x.svd (Ver. 1.0.0)
|
|
; @Core: Cortex-M3
|
|
; @Chip: TLE9883QTA62, TLE98812QTW60, TLE98832QTW62S, TLE9891QTA61,
|
|
; TLE9893QKW62S, TLE98912QTW60, TLE98912QTW61, TLE98932QKW62S,
|
|
; TLE98932QTA62, TLE98932QTA62S, TLE98932QTW62S
|
|
; @Copyright: (C) 1989-2023 Lauterbach GmbH, licensed for use with TRACE32(R) only
|
|
; --------------------------------------------------------------------------------
|
|
; $Id: pertle989x.per 17033 2023-11-20 14:27:46Z kwisniewski $
|
|
|
|
AUTOINDENT.ON CENTER TREE
|
|
ENUMDELIMITER ","
|
|
base ad:0x0
|
|
tree.close "Core Registers (Cortex-M3)"
|
|
AUTOINDENT.PUSH
|
|
AUTOINDENT.OFF
|
|
tree "System Control"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 11.
|
|
group 0x10--0x1b
|
|
line.long 0x00 "SYST_CSR,SysTick Control and Status Register"
|
|
bitfld.long 0x00 16. " COUNTFLAG ,Counter Flag" "Not counted,Counted"
|
|
bitfld.long 0x00 2. " CLKSOURCE ,Clock Source" "External,Core"
|
|
bitfld.long 0x00 1. " TICKINT ,SysTick Handler" "Not SysTick,SysTick"
|
|
textline " "
|
|
bitfld.long 0x00 0. " ENABLE ,Counter Enable" "Disabled,Enabled"
|
|
;group 0x14++0x03
|
|
line.long 0x04 "SYST_RVR,SysTick Reload Value Register"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,The value to load into the SYST_CVR when the counter reaches 0"
|
|
;group 0x18++0x03
|
|
line.long 0x08 "SYST_CVR,SysTick Current Value Register"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " CURRENT ,Current Value"
|
|
rgroup 0x1c++0x03
|
|
line.long 0x00 "SYST_CALIB,SysTick Calibration Value Register"
|
|
bitfld.long 0x00 31. " NOREF ,Indicates whether the implementation defined reference clock is implemented" "Implemented,Not implemented"
|
|
bitfld.long 0x00 30. " SKEW ,Indicates whether the 10ms calibration value is exact" "Exact,Inexact"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Holds a reload value to be used for 10ms (100Hz) timing"
|
|
textline " "
|
|
rgroup 0xd00++0x03
|
|
line.long 0x00 "CPUID,CPU ID Base Register"
|
|
hexmask.long.byte 0x00 24.--31. 1. " IMPLEMENTER ,Implementer Code"
|
|
bitfld.long 0x00 20.--23. " VARIANT ,Implementation Defined Variant Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 16.--19. " CONSTANT ,Constant" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x00 4.--15. 1. " PARTNO ,Number of Processor"
|
|
bitfld.long 0x00 0.--3. " REVISION ,Implementation Defined Revision Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group 0xd04--0xd17
|
|
line.long 0x00 "ICSR,Interrupt Control State Register"
|
|
bitfld.long 0x00 31. " NMIPENDSET ,Set Pending NMI Bit" "Not set,Set"
|
|
bitfld.long 0x00 28. " PENDSVSET ,Set Pending pendSV Bit" "Not set,Set"
|
|
bitfld.long 0x00 27. " PENDSVCLR ,Clear Pending pendSV Bit" "Not cleared,Cleared"
|
|
textline " "
|
|
bitfld.long 0x00 26. " PENDSTSET ,Set Pending SysTick Bit" "Not set,Set"
|
|
bitfld.long 0x00 25. " PENDSTCLR ,Clear Pending SysTick Bit" "Not cleared,Cleared"
|
|
bitfld.long 0x00 23. " ISRPREEMPT ,Use Only at Debug Time" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 22. " ISRPENDING ,Interrupt Pending Flag" "Not pending,Pending"
|
|
hexmask.long.word 0x00 12.--21. 1. " VECTPENDING ,Pending ISR Number Field"
|
|
bitfld.long 0x00 11. " RETTOBASE ,Interrupt Exception" "Active,Not active"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--8. 1. " VECTACTIVE ,Active ISR Number Field"
|
|
;group 0xd08++0x03
|
|
line.long 0x04 "VTOR,Vector Table Offset Register"
|
|
bitfld.long 0x04 29. " TBLBASE ,Table Base" "Code,RAM"
|
|
hexmask.long.tbyte 0x04 7.--28. 1. " TBLOFF ,Vector Table Base Offset Field"
|
|
;group 0xd0c++0x03
|
|
line.long 0x08 "AIRCR,Application Interrupt and Reset Control Register"
|
|
hexmask.long.word 0x08 16.--31. 1. " VECTKEY ,Register Key"
|
|
rbitfld.long 0x08 15. " ENDIANESS ,Data endianness Bit" "Little,Big"
|
|
bitfld.long 0x08 8.--10. " PRIGROUP ,Interrupt Priority Grouping Field" "[7:1]/[0],[7:2]/[1:0],[7:3]/[2:0],[7:4]/[3:0],[7:5]/[4:0],[7:6]/[5:0],[7]/[6:0],-/[7:0]"
|
|
textline " "
|
|
bitfld.long 0x08 2. " SYSRESETREQ ,System Reset Request" "Not requested,Requested"
|
|
bitfld.long 0x08 1. " VECTCLRACTIVE ,Clear Active Vector Bit" "Not cleared,Cleared all"
|
|
bitfld.long 0x08 0. " VECTRESET ,System Reset" "No reset,Reset"
|
|
;group 0xd10++0x03
|
|
line.long 0x0c "SCR,System Control Register"
|
|
bitfld.long 0x0c 4. " SEVONPEND ,Determines whether an interrupt transition from inactive state to pending state is a wakeup event" "Not wakeup,Wakeup"
|
|
bitfld.long 0x0c 2. " SLEEPDEEP ,Provides a qualifying hint indicating that waking from sleep might take longer" "Not deep sleep,Deep sleep"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " SLEEPONEXIT ,Determines whether, on an exit from an ISR that returns to the base level of execution priority, the processor enters a sleep state" "Disabled,Enabled"
|
|
;group 0xd14++0x03
|
|
line.long 0x10 "CCR,Configuration Control Register"
|
|
bitfld.long 0x10 9. " STKALIGN ,8-byte Stack Frame Alignment" "4-byte,8-byte"
|
|
bitfld.long 0x10 8. " BFHFNMIGN ,Enable NMI, Hard Fault and FAULTMASK to Ignore Bus Fault" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 4. " DIV_0_TRP ,Trap Divide by Zero" "Disabled,Enabled"
|
|
bitfld.long 0x10 3. " UNALIGN_TRP ,Trap for Unaligned Access" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 1. " USERSETMPEND ,Enable User Access to the Software Trigger Exception Register" "Disabled,Enabled"
|
|
bitfld.long 0x10 0. " NONEBASETHRDENA ,Control Entry to Thread Mode" "Only from last exception,Any level"
|
|
group 0xd18--0xd23
|
|
line.long 0x00 "SHPR1,SSystem Handler Priority Register 1"
|
|
hexmask.long.byte 0x00 24.--31. 1. " PRI_7 ,Priority of System Handler 7"
|
|
hexmask.long.byte 0x00 16.--23. 1. " PRI_6 ,Priority of system handler 6(UsageFault)"
|
|
hexmask.long.byte 0x00 8.--15. 1. " PRI_5 ,Priority of system handler 5(BusFault)"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " PRI_4 ,Priority of system handler 4(MemManage)"
|
|
line.long 0x04 "SHPR2,System Handler Priority Register 2"
|
|
hexmask.long.byte 0x04 24.--31. 1. " PRI_11 ,Priority of system handler 11(SVCall)"
|
|
hexmask.long.byte 0x04 16.--23. 1. " PRI_10 ,Priority of System Handler 10"
|
|
hexmask.long.byte 0x04 8.--15. 1. " PRI_9 ,Priority of System Handler 9"
|
|
textline " "
|
|
hexmask.long.byte 0x04 0.--7. 1. " PRI_8 ,Priority of System Handler 8"
|
|
line.long 0x08 "SHPR3,System Handler Priority Register 3"
|
|
hexmask.long.byte 0x08 24.--31. 1. " PRI_15 ,Priority of System Handler 15(SysTick)"
|
|
hexmask.long.byte 0x08 16.--23. 1. " PRI_14 ,Priority of System Handler 14(PendSV)"
|
|
hexmask.long.byte 0x08 8.--15. 1. " PRI_13 ,Priority of System Handler 13"
|
|
textline " "
|
|
hexmask.long.byte 0x08 0.--7. 1. " PRI_12 ,Priority of System Handler 12(DebugMonitor)"
|
|
group 0xd24++0x3
|
|
line.long 0x00 "SHCSR,System Handler Control and State Register"
|
|
bitfld.long 0x00 18. " USGFAULTENA ,USGFAULTENA" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " BUSFAULTENA ,BUSFAULTENA" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " MEMFAULTENA ,MEMFAULTENA" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SVCALLPENDED ,SVCall is Pended Started" "Not replaced,Replaced"
|
|
bitfld.long 0x00 14. " BUSFAULTPENDED ,BusFault is Pended Started" "Not replaced,Replaced"
|
|
bitfld.long 0x00 13. " MEMFAULTPENDED ,MemManage is Pended Started" "Not replaced,Replaced"
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYSTICKACT ,SysTick is Active" "Not active,Active"
|
|
bitfld.long 0x00 10. " PENDSVACT ,PendSV is Active" "Not active,Active"
|
|
bitfld.long 0x00 8. " MONITORACT ,Monitor is Active" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SVCALLACT ,SVCall is Active" "Not active,Active"
|
|
bitfld.long 0x00 3. " USGFAULTACT ,UsageFault is Active" "Not active,Active"
|
|
bitfld.long 0x00 1. " BUSFAULTACT ,BusFault is Active" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 0. " MEMFAULTACT ,MemManage is Active" "Not active,Active"
|
|
group 0xd28--0xd3b
|
|
line.byte 0x0 "MMFSR,Memory Manage Fault Status Register"
|
|
bitfld.byte 0x0 7. " MMARVALID ,Address Valid Flag" "Not valid,Valid"
|
|
bitfld.byte 0x0 4. " MSTKERR ,Stacking Access Violations" "No error,Error"
|
|
bitfld.byte 0x0 3. " MUNSTKERR ,Unstack Access Violations" "No error,Error"
|
|
textline " "
|
|
bitfld.byte 0x0 1. " DACCVIOL ,Data Access Violation" "No error,Error"
|
|
bitfld.byte 0x0 0. " IACCVIOL ,Instruction Access Violation" "No error,Error"
|
|
;group 0xd29++0x00
|
|
line.byte 0x01 "BFSR,Bus Fault Status Register"
|
|
bitfld.byte 0x01 7. " BFARVALID ,Address Valid" "Not valid,Valid"
|
|
bitfld.byte 0x01 4. " STKERR ,Stacking from Exception has Caused Bus Faults" "No error,Error"
|
|
bitfld.byte 0x01 3. " UNSTKERR ,Unstack from Exception Return has Caused Bus Faults" "No error,Error"
|
|
textline " "
|
|
bitfld.byte 0x01 2. " IMPRECISERR ,Imprecise Data Bus Error" "No error,Error"
|
|
bitfld.byte 0x01 1. " PRECISERR ,Precise Data Bus Error Return" "No error,Error"
|
|
bitfld.byte 0x01 0. " IBUSERR ,Instruction Bus Error Flag" "No error,Error"
|
|
;group 0xd2a++0x01
|
|
line.word 0x02 "USAFAULT,Usage Fault Status Register"
|
|
bitfld.word 0x02 9. " DIVBYZERO ,Illegal PC Load" "No error,Error"
|
|
bitfld.word 0x02 8. " UNALIGNED ,Illegal Unaligned Access" "No error,Error"
|
|
bitfld.word 0x02 3. " NOCP ,Attempt to use a coprocessor instruction" "No error,Error"
|
|
textline " "
|
|
bitfld.word 0x02 2. " INVPC ,Attempt to Load EXC_RETURN into PC Illegally" "No error,Error"
|
|
bitfld.word 0x02 1. " INVSTATE , Invalid Combination of EPSR and Instruction" "No error,Error"
|
|
bitfld.word 0x02 0. " UNDEFINSTR ,Illegal Processor State" "No error,Error"
|
|
;group 0xd2c++0x03
|
|
line.long 0x04 "HFSR,Hard Fault Status Register"
|
|
bitfld.long 0x04 31. " DEBUGEVT ,This Bit is Set if There is a Fault Related to Debug" "No error,Error"
|
|
bitfld.long 0x04 30. " FORCED ,Hard Fault Activated" "No error,Error"
|
|
bitfld.long 0x04 1. " VECTTBL ,Bus Fault" "No error,Error"
|
|
;group 0xd30++0x03
|
|
line.long 0x08 "DFSR,Debug Fault Status Register"
|
|
bitfld.long 0x08 4. " EXTERNAL ,External Debug Request Flag" "Not asserted,Asserted"
|
|
bitfld.long 0x08 3. " VCATCH ,Vector Catch Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x08 2. " DWTTRAP ,Data Watchpoint and Trace (DWT) Flag" "Not matched,Matched"
|
|
textline " "
|
|
bitfld.long 0x08 1. " BKPT ,BKPT Flag" "Not executed,Executed"
|
|
bitfld.long 0x08 0. " HALTED ,Halt Request Flag" "Not requested,Requested"
|
|
;group 0xd34++0x03
|
|
line.long 0xc "MMFAR,Memory Manage Fault Address Register"
|
|
;group 0xd38++0x03
|
|
line.long 0x10 "BFAR,Bus Fault Address Register"
|
|
wgroup 0xf00++0x03
|
|
line.long 0x00 "STIR,Software Trigger Interrupt Register"
|
|
hexmask.long.word 0x00 0.--8. 1. " INTID ,Indicates the interrupt to be triggered"
|
|
tree "Feature Registers"
|
|
width 10.
|
|
rgroup.long 0xD40++0x0B
|
|
line.long 0x00 "ID_PFR0,Processor Feature Register 0"
|
|
bitfld.long 0x00 4.--7. " STATE1 ,Thumb instruction set support" ",,,Supported,?..."
|
|
bitfld.long 0x00 0.--3. " STATE0 ,ARM instruction set support" "Not supported,?..."
|
|
line.long 0x04 "ID_PFR1,Processor Feature Register 1"
|
|
bitfld.long 0x04 8.--11. " MPROF ,M profile programmers' model" ",,2-stack,?..."
|
|
line.long 0x08 "ID_DFR0,Debug Feature Register 0"
|
|
bitfld.long 0x08 20.--23. " DBGMOD ,Support for memory-mapped debug model for M profile processors" "Not supported,Supported,?..."
|
|
hgroup.long 0xD4C++0x03
|
|
hide.long 0x00 "ID_AFR0,Auxiliary Feature Register 0"
|
|
rgroup.long 0xD50++0x03
|
|
line.long 0x00 "ID_MMFR0,Memory Model Feature Register 0"
|
|
bitfld.long 0x00 20.--23. " AUXREG ,Indicates the support for Auxiliary registers" "Not supported,ACTLR only,?..."
|
|
bitfld.long 0x00 16.--19. " TCMSUP ,Indicates the support for Tightly Coupled Memory (TCM)" "Not supported,Supported,?..."
|
|
bitfld.long 0x00 12.--15. " SHRLEV ,Indicates the number of shareability levels implemented" "Level 1,?..."
|
|
textline " "
|
|
bitfld.long 0x00 8.--11. " OUTMSHR ,Indicates the outermost shareability domain implemented" "Non-cacheable,,,,,,,,,,,,,,,Ignored"
|
|
bitfld.long 0x00 4.--7. " PMSASUP ,Indicates support for a PMSA" "Not supported,,,PMSAv7,?..."
|
|
hgroup.long 0xD54++0x03
|
|
hide.long 0x00 "ID_MMFR1,Memory Model Feature Register 1"
|
|
rgroup.long 0xD58++0x03
|
|
line.long 0x00 "ID_MMFR2,Memory Model Feature Register 2"
|
|
bitfld.long 0x00 24.--27. " WFISTALL ,Indicates the support for Wait For Interrupt (WFI) stalling" "Not supported,Supported,?..."
|
|
rgroup.long 0xD60++0x13
|
|
line.long 0x00 "ID_ISAR0,Instruction Set Attributes Register 0"
|
|
bitfld.long 0x00 24.--27. " DIVIDE ,Indicates the supported divide instructions" "Not supported,SDIV/UDIV,?..."
|
|
bitfld.long 0x00 20.--23. " DEBUG ,Indicates the supported debug instructions" "Not supported,BKPT,?..."
|
|
bitfld.long 0x00 16.--19. " COPROC ,Indicates the supported coprocessor instructions" "Not supported,CDP/LDC/MCR/STC,CDP2/LDC2/MCR2/STC2,MCRR/MRRC,MCRR2/MRRC2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CMPBRANCH ,Indicates the supported combined compare and branch instructions" "Not supported,CBNZ/CBZ,?..."
|
|
bitfld.long 0x00 8.--11. " BITFIELD ,Indicates the supported bitfield instructions" "Not supported,BFC/BFI/SBFX/UBFX,?..."
|
|
bitfld.long 0x00 4.--7. " BITCOUNT ,Indicates the supported bit counting instructions" "Not supported,CLZ,?..."
|
|
line.long 0x04 "ID_ISAR1,Instruction Set Attributes Register 1"
|
|
bitfld.long 0x04 24.--27. " INTERWORK ,Indicates the supported Interworking instructions" "Not supported,BX,BX/BLX,?..."
|
|
bitfld.long 0x04 20.--23. " IMMEDIATE ,Indicates the support for data-processing instructions with long immediates" "Not supported,ADDW/MOVW/MOVT/SUBW,?..."
|
|
bitfld.long 0x04 16.--19. " IFTHEN ,Indicates the supported IfThen instructions" "Not supported,IT,?..."
|
|
textline " "
|
|
bitfld.long 0x04 12.--15. " EXTEND ,Indicates the supported Extend instructions" "Not supported,Supported,Supported,?..."
|
|
line.long 0x08 "ID_ISAR2,Instruction Set Attributes Register 2"
|
|
bitfld.long 0x08 24.--27. " REVERSAL ,Indicates the supported reversal instructions" "Not supported,REV/REV16/REVSH,REV/REV16/REVSH/RBIT,?..."
|
|
bitfld.long 0x08 20.--23. " MULTU ,Indicates the supported advanced unsigned multiply instructions" "Not supported,UMULL/UMLAL,UMULL/UMLAL/UMAAL,?..."
|
|
bitfld.long 0x08 16.--19. " MULTS ,Indicates the supported advanced signed multiply instructions" "Not supported,Supported,Supported,Supported,?..."
|
|
textline " "
|
|
bitfld.long 0x08 12.--15. " MULT ,Indicates the supported additional multiply instructions" "Not supported,MLA,MLA/MLS,?..."
|
|
bitfld.long 0x08 8.--11. " MULTIACCESSINT ,Indicates the support for multi-access interruptible instructions" "Not supported,LDM/STM restartable,LDM/STM continuable,?..."
|
|
bitfld.long 0x08 4.--7. " MEMHINT ,Indicates the supported memory hint instructions" "Not supported,,,PLD/PLI,?..."
|
|
textline " "
|
|
bitfld.long 0x08 0.--3. " LOADSTORE ,Indicates the supported additional load and store instructions" "Not supported,LDRD/STRD,?..."
|
|
line.long 0x0C "ID_ISAR3,Instruction Set Attributes Register 3"
|
|
bitfld.long 0x0C 24.--27. " TRUENOP ,Indicates the support for a true NOP instruction" "Not supported,Supported,?..."
|
|
bitfld.long 0x0C 20.--23. " THUMBCOPY ,Indicates the supported non flag-setting MOV instructions" "Not supported,Supported,?..."
|
|
bitfld.long 0x0C 16.--19. " TABBRANCH ,Indicates the supported Table Branch instructions" "Not supported,TBB/TBH,?..."
|
|
textline " "
|
|
bitfld.long 0x0C 12.--15. " SYNCHPRIM ,Indicates the supported Table Branch instructions" "Not supported,Supported,Supported,Supported,?..."
|
|
bitfld.long 0x0C 8.--11. " SVC ,Indicates the supported SVC instructions" "Not supported,SVC,?..."
|
|
bitfld.long 0x0C 4.--7. " SIMD ,Indicates the supported SIMD instructions" "Not supported,Supported,,Supported,?..."
|
|
textline " "
|
|
bitfld.long 0x0C 0.--3. " SATURATE ,Indicates the supported Saturate instructions" "Not supported,QADD/QDADD/QDSUB/QSUB,?..."
|
|
line.long 0x10 "ID_ISAR4,Instruction Set Attributes Register 4"
|
|
bitfld.long 0x10 24.--27. " PSR_M ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,?..."
|
|
bitfld.long 0x10 20.--23. " SYNCHPRIMFRAC ,Indicates the supported M profile instructions to modify the PSRs" "Not supported,Supported,Supported,Supported,?..."
|
|
bitfld.long 0x10 16.--19. " BARRIER ,Indicates the supported Barrier instructions" "Not supported,DMB/DSB/ISB,?..."
|
|
textline " "
|
|
bitfld.long 0x10 8.--11. " WRITEBACK ,Indicates the support for writeback addressing modes" "Basic support,Full support,?..."
|
|
bitfld.long 0x10 4.--7. " WITHSHIFTS ,Indicates the support for instructions with shifts" "MOV/shift,Shift LSL 0-3,,Shift other,?..."
|
|
bitfld.long 0x10 0.--3. " UNPRIV ,Indicates the supported unprivileged instructions" "Not supported,LDRBT/LDRT/STRBT/STRT,LDRBT/LDRT/STRBT/STRT/LDRHT/LDRSBT/LDRSHTSTRHT,?..."
|
|
tree.end
|
|
tree "CoreSight Identification Registers"
|
|
width 6.
|
|
rgroup.long 0xFE0++0x0F
|
|
line.long 0x00 "PID0,Peripheral ID0"
|
|
hexmask.long.byte 0x00 0.--7. 1. " Part_Num[7:0] ,Part Number bits[7:0]"
|
|
line.long 0x04 "PID1,Peripheral ID1"
|
|
hexmask.long.byte 0x04 4.--7. 1. " JEP106ID[3:0] ,JEP106 ID code bits[3:0]"
|
|
hexmask.long.byte 0x04 0.--3. 1. " Part_Num[11:8] ,Part Number bits[11:8]"
|
|
line.long 0x08 "PID2,Peripheral ID2"
|
|
hexmask.long.byte 0x08 4.--7. 1. " Revision ,Revision"
|
|
bitfld.long 0x08 3. " JEDEC ,JEDEC assigned ID fields" "0,JEDEC"
|
|
hexmask.long.byte 0x08 0.--2. 1. " JEP106ID[6:4] ,JEP106 ID code bits[6:4]"
|
|
line.long 0x0c "PID3,Peripheral ID3"
|
|
hexmask.long.byte 0x0C 4.--7. 1. " RevAnd ,Minor revision field"
|
|
hexmask.long.byte 0x0C 0.--3. 1. " CMB ,Customer-modified block"
|
|
rgroup.long 0xFD0++0x03
|
|
line.long 0x00 "PID4,Peripheral Identification Register 4"
|
|
hexmask.long.byte 0x00 4.--7. 1. " Count ,4KB count"
|
|
hexmask.long.byte 0x00 0.--3. 1. " JEP106_CC ,JEP106 continuation code"
|
|
rgroup.long 0xFF0++0x0F
|
|
line.long 0x00 "CID0,Component ID0 (Preamble)"
|
|
line.long 0x04 "CID1,Component ID1"
|
|
hexmask.long.byte 0x04 4.--7. 1. " CC ,Component Class"
|
|
hexmask.long.byte 0x04 0.--3. 1. " Preamble ,Preamble"
|
|
line.long 0x08 "CID2,Component ID2"
|
|
line.long 0x0c "CID3,Component ID3"
|
|
tree.end
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Memory Protection Unit"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 15.
|
|
rgroup.long 0xD90++0x03
|
|
line.long 0x00 "MPU_TYPE,MPU Type Register"
|
|
bitfld.long 0x00 16.--23. " IREGION ,Instruction region" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..."
|
|
bitfld.long 0x00 8.--15. " DREGION ,Number of regions supported by the MPU" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..."
|
|
bitfld.long 0x00 0. " SEPARATE ,Indicates support for separate instruction and data address maps" "Not supported,Supported"
|
|
group.long 0xD94++0x03
|
|
line.long 0x00 "MPU_CTRL,MPU Control Register"
|
|
bitfld.long 0x00 2. " PRIVDEFENA ,Enables the default memory map as a background region for privileged access" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " HFNMIENA ,Handlers executing with priority less than 0 access memory with the MPU enabled or with the MPU disabled" "MPU disabled,MPU enabled"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables the MPU" "Disabled,Enabled"
|
|
group.long 0xD98++0x03
|
|
line.long 0x00 "MPU_RNR,MPU Region Number Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " REGION ,Indicates the memory region accessed by MPU_RBAR and MPU_RASR"
|
|
tree.close "MPU regions"
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x0
|
|
group.long 0xD9C++0x03 "Region 0"
|
|
saveout 0xD98 %l 0x0
|
|
line.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x0
|
|
line.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 0 (not implemented)"
|
|
saveout 0xD98 %l 0x0
|
|
hide.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x0
|
|
hide.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x1
|
|
group.long 0xD9C++0x03 "Region 1"
|
|
saveout 0xD98 %l 0x1
|
|
line.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x1
|
|
line.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 1 (not implemented)"
|
|
saveout 0xD98 %l 0x1
|
|
hide.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x1
|
|
hide.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x2
|
|
group.long 0xD9C++0x03 "Region 2"
|
|
saveout 0xD98 %l 0x2
|
|
line.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x2
|
|
line.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 2 (not implemented)"
|
|
saveout 0xD98 %l 0x2
|
|
hide.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x2
|
|
hide.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x3
|
|
group.long 0xD9C++0x03 "Region 3"
|
|
saveout 0xD98 %l 0x3
|
|
line.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x3
|
|
line.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 3 (not implemented)"
|
|
saveout 0xD98 %l 0x3
|
|
hide.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x3
|
|
hide.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x4
|
|
group.long 0xD9C++0x03 "Region 4"
|
|
saveout 0xD98 %l 0x4
|
|
line.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x4
|
|
line.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 4 (not implemented)"
|
|
saveout 0xD98 %l 0x4
|
|
hide.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x4
|
|
hide.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x5
|
|
group.long 0xD9C++0x03 "Region 5"
|
|
saveout 0xD98 %l 0x5
|
|
line.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x5
|
|
line.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 5 (not implemented)"
|
|
saveout 0xD98 %l 0x5
|
|
hide.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x5
|
|
hide.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x6
|
|
group.long 0xD9C++0x03 "Region 6"
|
|
saveout 0xD98 %l 0x6
|
|
line.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x6
|
|
line.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 6 (not implemented)"
|
|
saveout 0xD98 %l 0x6
|
|
hide.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x6
|
|
hide.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x7
|
|
group.long 0xD9C++0x03 "Region 7"
|
|
saveout 0xD98 %l 0x7
|
|
line.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x7
|
|
line.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 7 (not implemented)"
|
|
saveout 0xD98 %l 0x7
|
|
hide.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x7
|
|
hide.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x8
|
|
group.long 0xD9C++0x03 "Region 8"
|
|
saveout 0xD98 %l 0x8
|
|
line.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x8
|
|
line.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 8 (not implemented)"
|
|
saveout 0xD98 %l 0x8
|
|
hide.long 0x00 "MPU_RBAR8,MPU Region Base Address Register 8"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x8
|
|
hide.long 0x00 "MPU_RASR8,MPU Region Attribute and Size Register 8"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x9
|
|
group.long 0xD9C++0x03 "Region 9"
|
|
saveout 0xD98 %l 0x9
|
|
line.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x9
|
|
line.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 9 (not implemented)"
|
|
saveout 0xD98 %l 0x9
|
|
hide.long 0x00 "MPU_RBAR9,MPU Region Base Address Register 9"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x9
|
|
hide.long 0x00 "MPU_RASR9,MPU Region Attribute and Size Register 9"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xA
|
|
group.long 0xD9C++0x03 "Region 10"
|
|
saveout 0xD98 %l 0xA
|
|
line.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xA
|
|
line.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 10 (not implemented)"
|
|
saveout 0xD98 %l 0xA
|
|
hide.long 0x00 "MPU_RBAR10,MPU Region Base Address Register 10"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xA
|
|
hide.long 0x00 "MPU_RASR10,MPU Region Attribute and Size Register 10"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xB
|
|
group.long 0xD9C++0x03 "Region 11"
|
|
saveout 0xD98 %l 0xB
|
|
line.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xB
|
|
line.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 11 (not implemented)"
|
|
saveout 0xD98 %l 0xB
|
|
hide.long 0x00 "MPU_RBAR11,MPU Region Base Address Register 11"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xB
|
|
hide.long 0x00 "MPU_RASR11,MPU Region Attribute and Size Register 11"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xC
|
|
group.long 0xD9C++0x03 "Region 12"
|
|
saveout 0xD98 %l 0xC
|
|
line.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xC
|
|
line.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 12 (not implemented)"
|
|
saveout 0xD98 %l 0xC
|
|
hide.long 0x00 "MPU_RBAR12,MPU Region Base Address Register 12"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xC
|
|
hide.long 0x00 "MPU_RASR12,MPU Region Attribute and Size Register 12"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xD
|
|
group.long 0xD9C++0x03 "Region 13"
|
|
saveout 0xD98 %l 0xD
|
|
line.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xD
|
|
line.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 13 (not implemented)"
|
|
saveout 0xD98 %l 0xD
|
|
hide.long 0x00 "MPU_RBAR13,MPU Region Base Address Register 13"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xD
|
|
hide.long 0x00 "MPU_RASR13,MPU Region Attribute and Size Register 13"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xE
|
|
group.long 0xD9C++0x03 "Region 14"
|
|
saveout 0xD98 %l 0xE
|
|
line.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xE
|
|
line.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 14 (not implemented)"
|
|
saveout 0xD98 %l 0xE
|
|
hide.long 0x00 "MPU_RBAR14,MPU Region Base Address Register 14"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xE
|
|
hide.long 0x00 "MPU_RASR14,MPU Region Attribute and Size Register 14"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0xF
|
|
group.long 0xD9C++0x03 "Region 15"
|
|
saveout 0xD98 %l 0xF
|
|
line.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15"
|
|
hexmask.long 0x00 5.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xF
|
|
line.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RW,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,32 B,64 B,128 B,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 15 (not implemented)"
|
|
saveout 0xD98 %l 0xF
|
|
hide.long 0x00 "MPU_RBAR15,MPU Region Base Address Register 15"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0xF
|
|
hide.long 0x00 "MPU_RASR15,MPU Region Attribute and Size Register 15"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
tree.end
|
|
width 0x0b
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Nested Vectored Interrupt Controller"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 6.
|
|
rgroup.long 0x04++0x03
|
|
line.long 0x00 "ICTR,Interrupt Controller Type Register"
|
|
bitfld.long 0x00 0.--3. " INTLINESNUM ,Total Number of Interrupt" "0-32,33-64,65-96,97-128,129-160,161-192,193-224,225-240,?..."
|
|
tree "Interrupt Enable Registers"
|
|
width 23.
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00)
|
|
group.long 0x100++0x03
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02)
|
|
group.long 0x100++0x0B
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03)
|
|
group.long 0x100++0x0F
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04)
|
|
group.long 0x100++0x13
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05)
|
|
group.long 0x100++0x17
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06)
|
|
group.long 0x100++0x1B
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07)
|
|
group.long 0x100++0x1F
|
|
line.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " ENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " ENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " ENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " ENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " ENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " ENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " ENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " ENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " ENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " ENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " ENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " ENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " ENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " ENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " ENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " ENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " ENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " ENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " ENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " ENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " ENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " ENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " ENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " ENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " ENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " ENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " ENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " ENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " ENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " ENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " ENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " ENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " ENA63 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " ENA62 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " ENA61 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " ENA60 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " ENA59 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " ENA58 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " ENA57 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " ENA56 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " ENA55 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " ENA54 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " ENA53 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " ENA52 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " ENA51 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " ENA50 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " ENA49 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " ENA48 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " ENA47 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " ENA46 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " ENA45 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " ENA44 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " ENA43 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " ENA42 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " ENA41 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " ENA40 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " ENA39 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " ENA38 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " ENA37 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " ENA36 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " ENA35 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " ENA34 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " ENA33 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " ENA32 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " ENA95 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " ENA94 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " ENA93 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " ENA92 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " ENA91 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " ENA90 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " ENA89 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " ENA88 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " ENA87 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " ENA86 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " ENA85 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " ENA84 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " ENA83 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " ENA82 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " ENA81 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " ENA80 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " ENA79 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " ENA78 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " ENA77 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " ENA76 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " ENA75 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " ENA74 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " ENA73 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " ENA72 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " ENA71 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " ENA70 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " ENA69 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " ENA68 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " ENA67 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " ENA66 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " ENA65 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " ENA64 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " ENA127 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " ENA126 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " ENA125 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " ENA124 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " ENA123 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " ENA122 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " ENA121 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " ENA120 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " ENA119 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " ENA118 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " ENA117 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " ENA116 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " ENA115 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " ENA114 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " ENA113 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " ENA112 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " ENA111 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " ENA110 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " ENA109 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " ENA108 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " ENA107 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " ENA106 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " ENA105 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " ENA104 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " ENA103 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " ENA102 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " ENA101 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " ENA100 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " ENA99 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " ENA98 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " ENA97 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " ENA96 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " ENA159 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " ENA158 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " ENA157 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " ENA156 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " ENA155 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " ENA154 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " ENA153 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " ENA152 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " ENA151 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " ENA150 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " ENA149 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " ENA148 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " ENA147 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " ENA146 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " ENA145 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " ENA144 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " ENA143 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " ENA142 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " ENA141 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " ENA140 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " ENA139 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " ENA138 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " ENA137 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " ENA136 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " ENA135 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " ENA134 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " ENA133 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " ENA132 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " ENA131 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " ENA130 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " ENA129 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " ENA128 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " ENA191 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " ENA190 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " ENA189 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " ENA188 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " ENA187 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " ENA186 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " ENA185 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " ENA184 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " ENA183 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " ENA182 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " ENA181 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " ENA180 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " ENA179 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " ENA178 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " ENA177 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " ENA176 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " ENA175 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " ENA174 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " ENA173 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " ENA172 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " ENA171 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " ENA170 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " ENA169 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " ENA168 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " ENA167 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " ENA166 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " ENA165 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " ENA164 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " ENA163 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " ENA162 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " ENA161 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " ENA160 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x18 31. 0x18 31. 0x98 31. " ENA223 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 30. 0x18 30. 0x98 30. " ENA222 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 29. 0x18 29. 0x98 29. " ENA221 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 28. 0x18 28. 0x98 28. " ENA220 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 27. 0x18 27. 0x98 27. " ENA219 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 26. 0x18 26. 0x98 26. " ENA218 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 25. 0x18 25. 0x98 25. " ENA217 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 24. 0x18 24. 0x98 24. " ENA216 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 23. 0x18 23. 0x98 23. " ENA215 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 22. 0x18 22. 0x98 22. " ENA214 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 21. 0x18 21. 0x98 21. " ENA213 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 20. 0x18 20. 0x98 20. " ENA212 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 19. 0x18 19. 0x98 19. " ENA211 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 18. 0x18 18. 0x98 18. " ENA210 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 17. 0x18 17. 0x98 17. " ENA209 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 16. 0x18 16. 0x98 16. " ENA208 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 15. 0x18 15. 0x98 15. " ENA207 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 14. 0x18 14. 0x98 14. " ENA206 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 13. 0x18 13. 0x98 13. " ENA205 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 12. 0x18 12. 0x98 12. " ENA204 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 11. 0x18 11. 0x98 11. " ENA203 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 10. 0x18 10. 0x98 10. " ENA202 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 9. 0x18 9. 0x98 9. " ENA201 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 8. 0x18 8. 0x98 8. " ENA200 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 7. 0x18 7. 0x98 7. " ENA199 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 6. 0x18 6. 0x98 6. " ENA198 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 5. 0x18 5. 0x98 5. " ENA197 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 4. 0x18 4. 0x98 4. " ENA196 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 3. 0x18 3. 0x98 3. " ENA195 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 2. 0x18 2. 0x98 2. " ENA194 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x18 1. 0x18 1. 0x98 1. " ENA193 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x18 0. 0x18 0. 0x98 0. " ENA192 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
line.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register"
|
|
setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " ENA239 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " ENA238 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " ENA237 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " ENA236 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " ENA235 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " ENA234 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " ENA233 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " ENA232 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " ENA231 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " ENA230 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " ENA229 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " ENA228 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " ENA227 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " ENA226 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " ENA225 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " ENA224 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0x100++0x1F
|
|
hide.long 0x00 "IRQ0_31_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x04 "IRQ32_63_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x08 "IRQ64_95_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x0c "IRQ96_127_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x10 "IRQ128_159_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x14 "IRQ160_191_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x18 "IRQ192_223_EN_SET/CLR,Interrupt Enable Register"
|
|
hide.long 0x1c "IRQ224_239_EN_SET/CLR,Interrupt Enable Register"
|
|
endif
|
|
tree.end
|
|
tree "Interrupt Pending Registers"
|
|
width 23.
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00)
|
|
group.long 0x200++0x03
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01)
|
|
group.long 0x200++0x07
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02)
|
|
group.long 0x200++0x0B
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03)
|
|
group.long 0x200++0x0F
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04)
|
|
group.long 0x200++0x13
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05)
|
|
group.long 0x200++0x17
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06)
|
|
group.long 0x200++0x1B
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07)
|
|
group.long 0x200++0x1F
|
|
line.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " PEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " PEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " PEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " PEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " PEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " PEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " PEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " PEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " PEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " PEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " PEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " PEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " PEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " PEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " PEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " PEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " PEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " PEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " PEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " PEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " PEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " PEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " PEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " PEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " PEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " PEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " PEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " PEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " PEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " PEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " PEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " PEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x04 31. 0x04 31. 0x84 31. " PEN63 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 30. 0x04 30. 0x84 30. " PEN62 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 29. 0x04 29. 0x84 29. " PEN61 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 28. 0x04 28. 0x84 28. " PEN60 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 27. 0x04 27. 0x84 27. " PEN59 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 26. 0x04 26. 0x84 26. " PEN58 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 25. 0x04 25. 0x84 25. " PEN57 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 24. 0x04 24. 0x84 24. " PEN56 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 23. 0x04 23. 0x84 23. " PEN55 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 22. 0x04 22. 0x84 22. " PEN54 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 21. 0x04 21. 0x84 21. " PEN53 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 20. 0x04 20. 0x84 20. " PEN52 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 19. 0x04 19. 0x84 19. " PEN51 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 18. 0x04 18. 0x84 18. " PEN50 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 17. 0x04 17. 0x84 17. " PEN49 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 16. 0x04 16. 0x84 16. " PEN48 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 15. 0x04 15. 0x84 15. " PEN47 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 14. 0x04 14. 0x84 14. " PEN46 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 13. 0x04 13. 0x84 13. " PEN45 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 12. 0x04 12. 0x84 12. " PEN44 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 11. 0x04 11. 0x84 11. " PEN43 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 10. 0x04 10. 0x84 10. " PEN42 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 9. 0x04 9. 0x84 9. " PEN41 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 8. 0x04 8. 0x84 8. " PEN40 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 7. 0x04 7. 0x84 7. " PEN39 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 6. 0x04 6. 0x84 6. " PEN38 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 5. 0x04 5. 0x84 5. " PEN37 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 4. 0x04 4. 0x84 4. " PEN36 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 3. 0x04 3. 0x84 3. " PEN35 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 2. 0x04 2. 0x84 2. " PEN34 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x04 1. 0x04 1. 0x84 1. " PEN33 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x04 0. 0x04 0. 0x84 0. " PEN32 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x08 31. 0x08 31. 0x88 31. " PEN95 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 30. 0x08 30. 0x88 30. " PEN94 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 29. 0x08 29. 0x88 29. " PEN93 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 28. 0x08 28. 0x88 28. " PEN92 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 27. 0x08 27. 0x88 27. " PEN91 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 26. 0x08 26. 0x88 26. " PEN90 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 25. 0x08 25. 0x88 25. " PEN89 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 24. 0x08 24. 0x88 24. " PEN88 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 23. 0x08 23. 0x88 23. " PEN87 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 22. 0x08 22. 0x88 22. " PEN86 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 21. 0x08 21. 0x88 21. " PEN85 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 20. 0x08 20. 0x88 20. " PEN84 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 19. 0x08 19. 0x88 19. " PEN83 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 18. 0x08 18. 0x88 18. " PEN82 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 17. 0x08 17. 0x88 17. " PEN81 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 16. 0x08 16. 0x88 16. " PEN80 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 15. 0x08 15. 0x88 15. " PEN79 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 14. 0x08 14. 0x88 14. " PEN78 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 13. 0x08 13. 0x88 13. " PEN77 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 12. 0x08 12. 0x88 12. " PEN76 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 11. 0x08 11. 0x88 11. " PEN75 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 10. 0x08 10. 0x88 10. " PEN74 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 9. 0x08 9. 0x88 9. " PEN73 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 8. 0x08 8. 0x88 8. " PEN72 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 7. 0x08 7. 0x88 7. " PEN71 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 6. 0x08 6. 0x88 6. " PEN70 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 5. 0x08 5. 0x88 5. " PEN69 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 4. 0x08 4. 0x88 4. " PEN68 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 3. 0x08 3. 0x88 3. " PEN67 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 2. 0x08 2. 0x88 2. " PEN66 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x08 1. 0x08 1. 0x88 1. " PEN65 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x08 0. 0x08 0. 0x88 0. " PEN64 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x0c 31. 0x0c 31. 0x8c 31. " PEN127 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 30. 0x0c 30. 0x8c 30. " PEN126 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 29. 0x0c 29. 0x8c 29. " PEN125 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 28. 0x0c 28. 0x8c 28. " PEN124 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 27. 0x0c 27. 0x8c 27. " PEN123 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 26. 0x0c 26. 0x8c 26. " PEN122 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 25. 0x0c 25. 0x8c 25. " PEN121 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 24. 0x0c 24. 0x8c 24. " PEN120 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 23. 0x0c 23. 0x8c 23. " PEN119 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 22. 0x0c 22. 0x8c 22. " PEN118 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 21. 0x0c 21. 0x8c 21. " PEN117 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 20. 0x0c 20. 0x8c 20. " PEN116 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 19. 0x0c 19. 0x8c 19. " PEN115 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 18. 0x0c 18. 0x8c 18. " PEN114 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 17. 0x0c 17. 0x8c 17. " PEN113 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 16. 0x0c 16. 0x8c 16. " PEN112 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 15. 0x0c 15. 0x8c 15. " PEN111 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 14. 0x0c 14. 0x8c 14. " PEN110 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 13. 0x0c 13. 0x8c 13. " PEN109 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 12. 0x0c 12. 0x8c 12. " PEN108 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 11. 0x0c 11. 0x8c 11. " PEN107 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 10. 0x0c 10. 0x8c 10. " PEN106 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 9. 0x0c 9. 0x8c 9. " PEN105 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 8. 0x0c 8. 0x8c 8. " PEN104 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 7. 0x0c 7. 0x8c 7. " PEN103 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 6. 0x0c 6. 0x8c 6. " PEN102 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 5. 0x0c 5. 0x8c 5. " PEN101 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 4. 0x0c 4. 0x8c 4. " PEN100 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 3. 0x0c 3. 0x8c 3. " PEN99 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 2. 0x0c 2. 0x8c 2. " PEN98 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x0c 1. 0x0c 1. 0x8c 1. " PEN97 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x0c 0. 0x0c 0. 0x8c 0. " PEN96 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x10 31. 0x10 31. 0x90 31. " PEN159 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 30. 0x10 30. 0x90 30. " PEN158 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 29. 0x10 29. 0x90 29. " PEN157 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 28. 0x10 28. 0x90 28. " PEN156 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 27. 0x10 27. 0x90 27. " PEN155 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 26. 0x10 26. 0x90 26. " PEN154 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 25. 0x10 25. 0x90 25. " PEN153 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 24. 0x10 24. 0x90 24. " PEN152 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 23. 0x10 23. 0x90 23. " PEN151 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 22. 0x10 22. 0x90 22. " PEN150 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 21. 0x10 21. 0x90 21. " PEN149 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 20. 0x10 20. 0x90 20. " PEN148 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 19. 0x10 19. 0x90 19. " PEN147 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 18. 0x10 18. 0x90 18. " PEN146 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 17. 0x10 17. 0x90 17. " PEN145 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 16. 0x10 16. 0x90 16. " PEN144 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 15. 0x10 15. 0x90 15. " PEN143 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 14. 0x10 14. 0x90 14. " PEN142 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 13. 0x10 13. 0x90 13. " PEN141 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 12. 0x10 12. 0x90 12. " PEN140 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 11. 0x10 11. 0x90 11. " PEN139 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 10. 0x10 10. 0x90 10. " PEN138 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 9. 0x10 9. 0x90 9. " PEN137 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 8. 0x10 8. 0x90 8. " PEN136 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 7. 0x10 7. 0x90 7. " PEN135 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 6. 0x10 6. 0x90 6. " PEN134 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 5. 0x10 5. 0x90 5. " PEN133 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 4. 0x10 4. 0x90 4. " PEN132 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 3. 0x10 3. 0x90 3. " PEN131 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 2. 0x10 2. 0x90 2. " PEN130 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x10 1. 0x10 1. 0x90 1. " PEN129 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x10 0. 0x10 0. 0x90 0. " PEN128 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x14 31. 0x14 31. 0x94 31. " PEN191 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 30. 0x14 30. 0x94 30. " PEN190 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 29. 0x14 29. 0x94 29. " PEN189 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 28. 0x14 28. 0x94 28. " PEN188 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 27. 0x14 27. 0x94 27. " PEN187 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 26. 0x14 26. 0x94 26. " PEN186 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 25. 0x14 25. 0x94 25. " PEN185 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 24. 0x14 24. 0x94 24. " PEN184 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 23. 0x14 23. 0x94 23. " PEN183 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 22. 0x14 22. 0x94 22. " PEN182 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 21. 0x14 21. 0x94 21. " PEN181 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 20. 0x14 20. 0x94 20. " PEN180 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 19. 0x14 19. 0x94 19. " PEN179 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 18. 0x14 18. 0x94 18. " PEN178 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 17. 0x14 17. 0x94 17. " PEN177 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 16. 0x14 16. 0x94 16. " PEN176 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 15. 0x14 15. 0x94 15. " PEN175 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 14. 0x14 14. 0x94 14. " PEN174 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 13. 0x14 13. 0x94 13. " PEN173 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 12. 0x14 12. 0x94 12. " PEN172 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 11. 0x14 11. 0x94 11. " PEN171 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 10. 0x14 10. 0x94 10. " PEN170 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 9. 0x14 9. 0x94 9. " PEN169 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 8. 0x14 8. 0x94 8. " PEN168 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 7. 0x14 7. 0x94 7. " PEN167 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 6. 0x14 6. 0x94 6. " PEN166 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 5. 0x14 5. 0x94 5. " PEN165 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 4. 0x14 4. 0x94 4. " PEN164 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 3. 0x14 3. 0x94 3. " PEN163 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 2. 0x14 2. 0x94 2. " PEN162 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x14 1. 0x14 1. 0x94 1. " PEN161 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x14 0. 0x14 0. 0x94 0. " PEN160 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x18 31. 0x18 31. 0x98 31. " PEN223 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 30. 0x18 30. 0x98 30. " PEN222 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 29. 0x18 29. 0x98 29. " PEN221 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 28. 0x18 28. 0x98 28. " PEN220 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 27. 0x18 27. 0x98 27. " PEN219 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 26. 0x18 26. 0x98 26. " PEN218 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 25. 0x18 25. 0x98 25. " PEN217 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 24. 0x18 24. 0x98 24. " PEN216 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 23. 0x18 23. 0x98 23. " PEN215 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 22. 0x18 22. 0x98 22. " PEN214 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 21. 0x18 21. 0x98 21. " PEN213 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 20. 0x18 20. 0x98 20. " PEN212 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 19. 0x18 19. 0x98 19. " PEN211 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 18. 0x18 18. 0x98 18. " PEN210 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 17. 0x18 17. 0x98 17. " PEN209 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 16. 0x18 16. 0x98 16. " PEN208 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 15. 0x18 15. 0x98 15. " PEN207 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 14. 0x18 14. 0x98 14. " PEN206 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 13. 0x18 13. 0x98 13. " PEN205 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 12. 0x18 12. 0x98 12. " PEN204 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 11. 0x18 11. 0x98 11. " PEN203 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 10. 0x18 10. 0x98 10. " PEN202 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 9. 0x18 9. 0x98 9. " PEN201 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 8. 0x18 8. 0x98 8. " PEN200 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 7. 0x18 7. 0x98 7. " PEN199 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 6. 0x18 6. 0x98 6. " PEN198 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 5. 0x18 5. 0x98 5. " PEN197 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 4. 0x18 4. 0x98 4. " PEN196 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 3. 0x18 3. 0x98 3. " PEN195 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 2. 0x18 2. 0x98 2. " PEN194 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x18 1. 0x18 1. 0x98 1. " PEN193 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x18 0. 0x18 0. 0x98 0. " PEN192 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
line.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register"
|
|
setclrfld.long 0x1c 15. 0x1c 15. 0x9c 15. " PEN239 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 14. 0x1c 14. 0x9c 14. " PEN238 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 13. 0x1c 13. 0x9c 13. " PEN237 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 12. 0x1c 12. 0x9c 12. " PEN236 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 11. 0x1c 11. 0x9c 11. " PEN235 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 10. 0x1c 10. 0x9c 10. " PEN234 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x1c 9. 0x1c 9. 0x9c 9. " PEN233 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 8. 0x1c 8. 0x9c 8. " PEN232 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 7. 0x1c 7. 0x9c 7. " PEN231 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 6. 0x1c 6. 0x9c 6. " PEN230 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 5. 0x1c 5. 0x9c 5. " PEN229 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 4. 0x1c 4. 0x9c 4. " PEN228 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x1c 3. 0x1c 3. 0x9c 3. " PEN227 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 2. 0x1c 2. 0x9c 2. " PEN226 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 1. 0x1c 1. 0x9c 1. " PEN225 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x1c 0. 0x1c 0. 0x9c 0. " PEN224 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
else
|
|
hgroup.long 0x200++0x1F
|
|
hide.long 0x00 "IRQ0_31_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x04 "IRQ32_63_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x08 "IRQ64_95_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x0c "IRQ96_127_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x10 "IRQ128_159_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x14 "IRQ160_191_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x18 "IRQ192_223_PEN_SET/CLR,Interrupt Pending Register"
|
|
hide.long 0x1c "IRQ224_239_PEN_SET/CLR,Interrupt Pending Register"
|
|
endif
|
|
tree.end
|
|
tree "Interrupt Active Bit Registers"
|
|
width 9.
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00)
|
|
rgroup.long 0x300++0x03
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01)
|
|
rgroup.long 0x300++0x07
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02)
|
|
rgroup.long 0x300++0x0B
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03)
|
|
rgroup.long 0x300++0x0F
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04)
|
|
rgroup.long 0x300++0x13
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x10 "ACTIVE5,Active Bit Register 5"
|
|
bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05)
|
|
rgroup.long 0x300++0x17
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x10 "ACTIVE5,Active Bit Register 5"
|
|
bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x14 "ACTIVE6,Active Bit Register 6"
|
|
bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06)
|
|
rgroup.long 0x300++0x1B
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x10 "ACTIVE5,Active Bit Register 5"
|
|
bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x14 "ACTIVE6,Active Bit Register 6"
|
|
bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x18 "ACTIVE7,Active Bit Register 7"
|
|
bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07)
|
|
rgroup.long 0x300++0x1F
|
|
line.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
bitfld.long 0x00 31. " ACTIVE31 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 30. " ACTIVE30 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 29. " ACTIVE29 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 28. " ACTIVE28 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 27. " ACTIVE27 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 26. " ACTIVE26 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ACTIVE25 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 24. " ACTIVE24 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 23. " ACTIVE23 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 22. " ACTIVE22 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 21. " ACTIVE21 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 20. " ACTIVE20 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ACTIVE19 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 18. " ACTIVE18 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 17. " ACTIVE17 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 16. " ACTIVE16 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 15. " ACTIVE15 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 14. " ACTIVE14 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ACTIVE13 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 12. " ACTIVE12 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 11. " ACTIVE11 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 10. " ACTIVE10 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 9. " ACTIVE9 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 8. " ACTIVE8 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ACTIVE7 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 6. " ACTIVE6 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 5. " ACTIVE5 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 4. " ACTIVE4 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 3. " ACTIVE3 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 2. " ACTIVE2 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ACTIVE1 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x00 0. " ACTIVE0 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
bitfld.long 0x04 31. " ACTIVE63 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 30. " ACTIVE62 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 29. " ACTIVE61 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 28. " ACTIVE60 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 27. " ACTIVE59 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 26. " ACTIVE58 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 25. " ACTIVE57 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 24. " ACTIVE56 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 23. " ACTIVE55 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 22. " ACTIVE54 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 21. " ACTIVE53 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 20. " ACTIVE52 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 19. " ACTIVE51 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 18. " ACTIVE50 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 17. " ACTIVE49 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 16. " ACTIVE48 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 15. " ACTIVE47 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 14. " ACTIVE46 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 13. " ACTIVE45 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 12. " ACTIVE44 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 11. " ACTIVE43 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 10. " ACTIVE42 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 9. " ACTIVE41 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 8. " ACTIVE40 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 7. " ACTIVE39 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 6. " ACTIVE38 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 5. " ACTIVE37 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 4. " ACTIVE36 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 3. " ACTIVE35 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 2. " ACTIVE34 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ACTIVE33 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x04 0. " ACTIVE32 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
bitfld.long 0x08 31. " ACTIVE95 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 30. " ACTIVE94 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 29. " ACTIVE93 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 28. " ACTIVE92 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 27. " ACTIVE91 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 26. " ACTIVE90 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 25. " ACTIVE89 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 24. " ACTIVE88 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 23. " ACTIVE87 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 22. " ACTIVE86 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 21. " ACTIVE85 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 20. " ACTIVE84 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 19. " ACTIVE83 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 18. " ACTIVE82 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 17. " ACTIVE81 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 16. " ACTIVE80 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 15. " ACTIVE79 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 14. " ACTIVE78 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 13. " ACTIVE77 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 12. " ACTIVE76 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 11. " ACTIVE75 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 10. " ACTIVE74 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 9. " ACTIVE73 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 8. " ACTIVE72 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 7. " ACTIVE71 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 6. " ACTIVE70 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 5. " ACTIVE69 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 4. " ACTIVE68 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 3. " ACTIVE67 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 2. " ACTIVE66 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x08 1. " ACTIVE65 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x08 0. " ACTIVE64 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
bitfld.long 0x0c 31. " ACTIVE127 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 30. " ACTIVE126 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 29. " ACTIVE125 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 28. " ACTIVE124 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 27. " ACTIVE123 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 26. " ACTIVE122 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " ACTIVE121 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 24. " ACTIVE120 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 23. " ACTIVE119 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 22. " ACTIVE118 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 21. " ACTIVE117 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 20. " ACTIVE116 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " ACTIVE115 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 18. " ACTIVE114 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 17. " ACTIVE113 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 16. " ACTIVE112 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 15. " ACTIVE111 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 14. " ACTIVE110 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " ACTIVE109 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 12. " ACTIVE108 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 11. " ACTIVE107 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 10. " ACTIVE106 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 9. " ACTIVE105 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 8. " ACTIVE104 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " ACTIVE103 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 6. " ACTIVE102 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 5. " ACTIVE101 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 4. " ACTIVE100 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 3. " ACTIVE99 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 2. " ACTIVE98 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " ACTIVE97 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x0c 0. " ACTIVE96 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x10 "ACTIVE5,Active Bit Register 5"
|
|
bitfld.long 0x10 31. " ACTIVE159 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 30. " ACTIVE158 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 29. " ACTIVE157 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 28. " ACTIVE156 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 27. " ACTIVE155 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 26. " ACTIVE154 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 25. " ACTIVE153 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 24. " ACTIVE152 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 23. " ACTIVE151 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 22. " ACTIVE150 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 21. " ACTIVE149 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 20. " ACTIVE148 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ACTIVE147 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 18. " ACTIVE146 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 17. " ACTIVE145 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 16. " ACTIVE144 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 15. " ACTIVE143 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 14. " ACTIVE142 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 13. " ACTIVE141 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 12. " ACTIVE140 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 11. " ACTIVE139 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 10. " ACTIVE138 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 9. " ACTIVE137 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 8. " ACTIVE136 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ACTIVE135 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 6. " ACTIVE134 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 5. " ACTIVE133 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 4. " ACTIVE132 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 3. " ACTIVE131 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 2. " ACTIVE130 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x10 1. " ACTIVE129 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x10 0. " ACTIVE128 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x14 "ACTIVE6,Active Bit Register 6"
|
|
bitfld.long 0x14 31. " ACTIVE191 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 30. " ACTIVE190 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 29. " ACTIVE189 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 28. " ACTIVE188 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 27. " ACTIVE187 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 26. " ACTIVE186 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 25. " ACTIVE185 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 24. " ACTIVE184 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 23. " ACTIVE183 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 22. " ACTIVE182 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 21. " ACTIVE181 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 20. " ACTIVE180 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ACTIVE179 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 18. " ACTIVE178 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 17. " ACTIVE177 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 16. " ACTIVE176 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 15. " ACTIVE175 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 14. " ACTIVE174 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 13. " ACTIVE173 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 12. " ACTIVE172 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 11. " ACTIVE171 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 10. " ACTIVE170 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 9. " ACTIVE169 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 8. " ACTIVE168 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ACTIVE167 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 6. " ACTIVE166 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 5. " ACTIVE165 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 4. " ACTIVE164 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 3. " ACTIVE163 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 2. " ACTIVE162 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x14 1. " ACTIVE161 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x14 0. " ACTIVE160 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x18 "ACTIVE7,Active Bit Register 7"
|
|
bitfld.long 0x18 31. " ACTIVE223 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 30. " ACTIVE222 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 29. " ACTIVE221 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 28. " ACTIVE220 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 27. " ACTIVE219 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 26. " ACTIVE218 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 25. " ACTIVE217 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 24. " ACTIVE216 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 23. " ACTIVE215 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 22. " ACTIVE214 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 21. " ACTIVE213 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 20. " ACTIVE212 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 19. " ACTIVE211 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 18. " ACTIVE210 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 17. " ACTIVE209 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 16. " ACTIVE208 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 15. " ACTIVE207 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 14. " ACTIVE206 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 13. " ACTIVE205 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 12. " ACTIVE204 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 11. " ACTIVE203 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 10. " ACTIVE202 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 9. " ACTIVE201 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 8. " ACTIVE200 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 7. " ACTIVE199 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 6. " ACTIVE198 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 5. " ACTIVE197 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 4. " ACTIVE196 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 3. " ACTIVE195 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 2. " ACTIVE194 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x18 1. " ACTIVE193 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x18 0. " ACTIVE192 ,Interrupt Active Flag" "Not active,Active"
|
|
line.long 0x1c "ACTIVE8,Active Bit Register 8"
|
|
bitfld.long 0x1c 15. " ACTIVE239 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 14. " ACTIVE238 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 13. " ACTIVE237 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 12. " ACTIVE236 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 11. " ACTIVE235 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 10. " ACTIVE234 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x1c 9. " ACTIVE233 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 8. " ACTIVE232 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 7. " ACTIVE231 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 6. " ACTIVE230 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 5. " ACTIVE229 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 4. " ACTIVE228 ,Interrupt Active Flag" "Not active,Active"
|
|
textline " "
|
|
bitfld.long 0x1c 3. " ACTIVE227 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 2. " ACTIVE226 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 1. " ACTIVE225 ,Interrupt Active Flag" "Not active,Active"
|
|
bitfld.long 0x1c 0. " ACTIVE224 ,Interrupt Active Flag" "Not active,Active"
|
|
else
|
|
hgroup.long 0x300++0x1F
|
|
hide.long 0x00 "ACTIVE1,Active Bit Register 1"
|
|
hide.long 0x04 "ACTIVE2,Active Bit Register 2"
|
|
hide.long 0x08 "ACTIVE3,Active Bit Register 3"
|
|
hide.long 0x0c "ACTIVE4,Active Bit Register 4"
|
|
hide.long 0x10 "ACTIVE5,Active Bit Register 5"
|
|
hide.long 0x14 "ACTIVE6,Active Bit Register 6"
|
|
hide.long 0x18 "ACTIVE7,Active Bit Register 7"
|
|
hide.long 0x1c "ACTIVE8,Active Bit Register 8"
|
|
endif
|
|
tree.end
|
|
tree "Interrupt Priority Registers"
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x00)
|
|
group.long 0x400++0x1F
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x01)
|
|
group.long 0x400++0x3F
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x02)
|
|
group.long 0x400++0x5F
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x03)
|
|
group.long 0x400++0x7F
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
line.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority"
|
|
hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority"
|
|
hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority"
|
|
hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority"
|
|
line.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority"
|
|
hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority"
|
|
hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority"
|
|
hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority"
|
|
line.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority"
|
|
hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority"
|
|
hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority"
|
|
hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority"
|
|
line.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority"
|
|
hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority"
|
|
hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority"
|
|
hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority"
|
|
line.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority"
|
|
hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority"
|
|
hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority"
|
|
hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority"
|
|
line.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority"
|
|
hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority"
|
|
hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority"
|
|
hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority"
|
|
line.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority"
|
|
hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority"
|
|
hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority"
|
|
hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority"
|
|
line.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority"
|
|
hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority"
|
|
hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority"
|
|
hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x04)
|
|
group.long 0x400++0x9F
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
line.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority"
|
|
hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority"
|
|
hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority"
|
|
hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority"
|
|
line.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority"
|
|
hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority"
|
|
hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority"
|
|
hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority"
|
|
line.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority"
|
|
hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority"
|
|
hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority"
|
|
hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority"
|
|
line.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority"
|
|
hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority"
|
|
hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority"
|
|
hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority"
|
|
line.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority"
|
|
hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority"
|
|
hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority"
|
|
hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority"
|
|
line.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority"
|
|
hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority"
|
|
hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority"
|
|
hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority"
|
|
line.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority"
|
|
hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority"
|
|
hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority"
|
|
hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority"
|
|
line.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority"
|
|
hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority"
|
|
hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority"
|
|
hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority"
|
|
line.long 0x80 "IPR32,Interrupt Priority Register"
|
|
hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority"
|
|
hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority"
|
|
hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority"
|
|
hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority"
|
|
line.long 0x84 "IPR33,Interrupt Priority Register"
|
|
hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority"
|
|
hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority"
|
|
hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority"
|
|
hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority"
|
|
line.long 0x88 "IPR34,Interrupt Priority Register"
|
|
hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority"
|
|
hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority"
|
|
hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority"
|
|
hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority"
|
|
line.long 0x8C "IPR35,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority"
|
|
hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority"
|
|
hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority"
|
|
hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority"
|
|
line.long 0x90 "IPR36,Interrupt Priority Register"
|
|
hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority"
|
|
hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority"
|
|
hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority"
|
|
hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority"
|
|
line.long 0x94 "IPR37,Interrupt Priority Register"
|
|
hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority"
|
|
hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority"
|
|
hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority"
|
|
hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority"
|
|
line.long 0x98 "IPR38,Interrupt Priority Register"
|
|
hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority"
|
|
hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority"
|
|
hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority"
|
|
hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority"
|
|
line.long 0x9C "IPR39,Interrupt Priority Register"
|
|
hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority"
|
|
hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority"
|
|
hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority"
|
|
hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x05)
|
|
group.long 0x400++0xBF
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
line.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority"
|
|
hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority"
|
|
hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority"
|
|
hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority"
|
|
line.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority"
|
|
hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority"
|
|
hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority"
|
|
hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority"
|
|
line.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority"
|
|
hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority"
|
|
hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority"
|
|
hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority"
|
|
line.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority"
|
|
hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority"
|
|
hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority"
|
|
hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority"
|
|
line.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority"
|
|
hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority"
|
|
hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority"
|
|
hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority"
|
|
line.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority"
|
|
hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority"
|
|
hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority"
|
|
hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority"
|
|
line.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority"
|
|
hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority"
|
|
hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority"
|
|
hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority"
|
|
line.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority"
|
|
hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority"
|
|
hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority"
|
|
hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority"
|
|
line.long 0x80 "IPR32,Interrupt Priority Register"
|
|
hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority"
|
|
hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority"
|
|
hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority"
|
|
hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority"
|
|
line.long 0x84 "IPR33,Interrupt Priority Register"
|
|
hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority"
|
|
hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority"
|
|
hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority"
|
|
hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority"
|
|
line.long 0x88 "IPR34,Interrupt Priority Register"
|
|
hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority"
|
|
hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority"
|
|
hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority"
|
|
hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority"
|
|
line.long 0x8C "IPR35,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority"
|
|
hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority"
|
|
hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority"
|
|
hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority"
|
|
line.long 0x90 "IPR36,Interrupt Priority Register"
|
|
hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority"
|
|
hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority"
|
|
hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority"
|
|
hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority"
|
|
line.long 0x94 "IPR37,Interrupt Priority Register"
|
|
hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority"
|
|
hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority"
|
|
hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority"
|
|
hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority"
|
|
line.long 0x98 "IPR38,Interrupt Priority Register"
|
|
hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority"
|
|
hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority"
|
|
hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority"
|
|
hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority"
|
|
line.long 0x9C "IPR39,Interrupt Priority Register"
|
|
hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority"
|
|
hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority"
|
|
hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority"
|
|
hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority"
|
|
line.long 0xA0 "IPR40,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority"
|
|
hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority"
|
|
hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority"
|
|
hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority"
|
|
line.long 0xA4 "IPR41,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority"
|
|
hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority"
|
|
hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority"
|
|
hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority"
|
|
line.long 0xA8 "IPR42,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority"
|
|
hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority"
|
|
hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority"
|
|
hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority"
|
|
line.long 0xAC "IPR43,Interrupt Priority Register"
|
|
hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority"
|
|
hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority"
|
|
hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority"
|
|
hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority"
|
|
line.long 0xB0 "IPR44,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority"
|
|
hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority"
|
|
hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority"
|
|
hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority"
|
|
line.long 0xB4 "IPR45,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority"
|
|
hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority"
|
|
hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority"
|
|
hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority"
|
|
line.long 0xB8 "IPR46,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority"
|
|
hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority"
|
|
hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority"
|
|
hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority"
|
|
line.long 0xBC "IPR47,Interrupt Priority Register"
|
|
hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority"
|
|
hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority"
|
|
hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority"
|
|
hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x06)
|
|
group.long 0x400++0xDF
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
line.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority"
|
|
hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority"
|
|
hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority"
|
|
hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority"
|
|
line.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority"
|
|
hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority"
|
|
hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority"
|
|
hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority"
|
|
line.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority"
|
|
hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority"
|
|
hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority"
|
|
hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority"
|
|
line.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority"
|
|
hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority"
|
|
hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority"
|
|
hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority"
|
|
line.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority"
|
|
hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority"
|
|
hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority"
|
|
hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority"
|
|
line.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority"
|
|
hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority"
|
|
hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority"
|
|
hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority"
|
|
line.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority"
|
|
hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority"
|
|
hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority"
|
|
hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority"
|
|
line.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority"
|
|
hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority"
|
|
hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority"
|
|
hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority"
|
|
line.long 0x80 "IPR32,Interrupt Priority Register"
|
|
hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority"
|
|
hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority"
|
|
hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority"
|
|
hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority"
|
|
line.long 0x84 "IPR33,Interrupt Priority Register"
|
|
hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority"
|
|
hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority"
|
|
hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority"
|
|
hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority"
|
|
line.long 0x88 "IPR34,Interrupt Priority Register"
|
|
hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority"
|
|
hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority"
|
|
hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority"
|
|
hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority"
|
|
line.long 0x8C "IPR35,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority"
|
|
hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority"
|
|
hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority"
|
|
hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority"
|
|
line.long 0x90 "IPR36,Interrupt Priority Register"
|
|
hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority"
|
|
hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority"
|
|
hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority"
|
|
hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority"
|
|
line.long 0x94 "IPR37,Interrupt Priority Register"
|
|
hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority"
|
|
hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority"
|
|
hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority"
|
|
hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority"
|
|
line.long 0x98 "IPR38,Interrupt Priority Register"
|
|
hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority"
|
|
hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority"
|
|
hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority"
|
|
hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority"
|
|
line.long 0x9C "IPR39,Interrupt Priority Register"
|
|
hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority"
|
|
hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority"
|
|
hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority"
|
|
hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority"
|
|
line.long 0xA0 "IPR40,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority"
|
|
hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority"
|
|
hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority"
|
|
hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority"
|
|
line.long 0xA4 "IPR41,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority"
|
|
hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority"
|
|
hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority"
|
|
hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority"
|
|
line.long 0xA8 "IPR42,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority"
|
|
hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority"
|
|
hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority"
|
|
hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority"
|
|
line.long 0xAC "IPR43,Interrupt Priority Register"
|
|
hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority"
|
|
hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority"
|
|
hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority"
|
|
hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority"
|
|
line.long 0xB0 "IPR44,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority"
|
|
hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority"
|
|
hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority"
|
|
hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority"
|
|
line.long 0xB4 "IPR45,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority"
|
|
hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority"
|
|
hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority"
|
|
hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority"
|
|
line.long 0xB8 "IPR46,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority"
|
|
hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority"
|
|
hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority"
|
|
hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority"
|
|
line.long 0xBC "IPR47,Interrupt Priority Register"
|
|
hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority"
|
|
hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority"
|
|
hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority"
|
|
hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority"
|
|
line.long 0xC0 "IPR48,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority"
|
|
hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority"
|
|
hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority"
|
|
hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority"
|
|
line.long 0xC4 "IPR49,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority"
|
|
hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority"
|
|
hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority"
|
|
hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority"
|
|
line.long 0xC8 "IPR50,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority"
|
|
hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority"
|
|
hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority"
|
|
hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority"
|
|
line.long 0xCC "IPR51,Interrupt Priority Register"
|
|
hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority"
|
|
hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority"
|
|
hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority"
|
|
hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority"
|
|
line.long 0xD0 "IPR52,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority"
|
|
hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority"
|
|
hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority"
|
|
hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority"
|
|
line.long 0xD4 "IPR53,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority"
|
|
hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority"
|
|
hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority"
|
|
hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority"
|
|
line.long 0xD8 "IPR54,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority"
|
|
hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority"
|
|
hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority"
|
|
hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority"
|
|
line.long 0xDC "IPR55,Interrupt Priority Register"
|
|
hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority"
|
|
hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority"
|
|
hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority"
|
|
hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority"
|
|
elif (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0x04))&0x0F)==0x07)
|
|
group.long 0x400++0xEF
|
|
line.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. " PRI_3 ,Interrupt 3 Priority"
|
|
hexmask.long.byte 0x0 16.--23. 1. " PRI_2 ,Interrupt 2 Priority"
|
|
hexmask.long.byte 0x0 8.--15. 1. " PRI_1 ,Interrupt 1 Priority"
|
|
hexmask.long.byte 0x0 0.--7. 1. " PRI_0 ,Interrupt 0 Priority"
|
|
line.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. " PRI_7 ,Interrupt 7 Priority"
|
|
hexmask.long.byte 0x4 16.--23. 1. " PRI_6 ,Interrupt 6 Priority"
|
|
hexmask.long.byte 0x4 8.--15. 1. " PRI_5 ,Interrupt 5 Priority"
|
|
hexmask.long.byte 0x4 0.--7. 1. " PRI_4 ,Interrupt 4 Priority"
|
|
line.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. " PRI_11 ,Interrupt 11 Priority"
|
|
hexmask.long.byte 0x8 16.--23. 1. " PRI_10 ,Interrupt 10 Priority"
|
|
hexmask.long.byte 0x8 8.--15. 1. " PRI_9 ,Interrupt 9 Priority"
|
|
hexmask.long.byte 0x8 0.--7. 1. " PRI_8 ,Interrupt 8 Priority"
|
|
line.long 0xC "IPR3,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. " PRI_15 ,Interrupt 15 Priority"
|
|
hexmask.long.byte 0xC 16.--23. 1. " PRI_14 ,Interrupt 14 Priority"
|
|
hexmask.long.byte 0xC 8.--15. 1. " PRI_13 ,Interrupt 13 Priority"
|
|
hexmask.long.byte 0xC 0.--7. 1. " PRI_12 ,Interrupt 12 Priority"
|
|
line.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. " PRI_19 ,Interrupt 19 Priority"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PRI_18 ,Interrupt 18 Priority"
|
|
hexmask.long.byte 0x10 8.--15. 1. " PRI_17 ,Interrupt 17 Priority"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PRI_16 ,Interrupt 16 Priority"
|
|
line.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. " PRI_23 ,Interrupt 23 Priority"
|
|
hexmask.long.byte 0x14 16.--23. 1. " PRI_22 ,Interrupt 22 Priority"
|
|
hexmask.long.byte 0x14 8.--15. 1. " PRI_21 ,Interrupt 21 Priority"
|
|
hexmask.long.byte 0x14 0.--7. 1. " PRI_20 ,Interrupt 20 Priority"
|
|
line.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. " PRI_27 ,Interrupt 27 Priority"
|
|
hexmask.long.byte 0x18 16.--23. 1. " PRI_26 ,Interrupt 26 Priority"
|
|
hexmask.long.byte 0x18 8.--15. 1. " PRI_25 ,Interrupt 25 Priority"
|
|
hexmask.long.byte 0x18 0.--7. 1. " PRI_24 ,Interrupt 24 Priority"
|
|
line.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hexmask.long.byte 0x1C 24.--31. 1. " PRI_31 ,Interrupt 31 Priority"
|
|
hexmask.long.byte 0x1C 16.--23. 1. " PRI_30 ,Interrupt 30 Priority"
|
|
hexmask.long.byte 0x1C 8.--15. 1. " PRI_29 ,Interrupt 29 Priority"
|
|
hexmask.long.byte 0x1C 0.--7. 1. " PRI_28 ,Interrupt 28 Priority"
|
|
line.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hexmask.long.byte 0x20 24.--31. 1. " PRI_35 ,Interrupt 35 Priority"
|
|
hexmask.long.byte 0x20 16.--23. 1. " PRI_34 ,Interrupt 34 Priority"
|
|
hexmask.long.byte 0x20 8.--15. 1. " PRI_33 ,Interrupt 33 Priority"
|
|
hexmask.long.byte 0x20 0.--7. 1. " PRI_32 ,Interrupt 32 Priority"
|
|
line.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hexmask.long.byte 0x24 24.--31. 1. " PRI_39 ,Interrupt 39 Priority"
|
|
hexmask.long.byte 0x24 16.--23. 1. " PRI_38 ,Interrupt 38 Priority"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PRI_37 ,Interrupt 37 Priority"
|
|
hexmask.long.byte 0x24 0.--7. 1. " PRI_36 ,Interrupt 36 Priority"
|
|
line.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hexmask.long.byte 0x28 24.--31. 1. " PRI_43 ,Interrupt 43 Priority"
|
|
hexmask.long.byte 0x28 16.--23. 1. " PRI_42 ,Interrupt 42 Priority"
|
|
hexmask.long.byte 0x28 8.--15. 1. " PRI_41 ,Interrupt 41 Priority"
|
|
hexmask.long.byte 0x28 0.--7. 1. " PRI_40 ,Interrupt 40 Priority"
|
|
line.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hexmask.long.byte 0x2C 24.--31. 1. " PRI_47 ,Interrupt 47 Priority"
|
|
hexmask.long.byte 0x2C 16.--23. 1. " PRI_46 ,Interrupt 46 Priority"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " PRI_45 ,Interrupt 45 Priority"
|
|
hexmask.long.byte 0x2C 0.--7. 1. " PRI_44 ,Interrupt 44 Priority"
|
|
line.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hexmask.long.byte 0x30 24.--31. 1. " PRI_51 ,Interrupt 51 Priority"
|
|
hexmask.long.byte 0x30 16.--23. 1. " PRI_50 ,Interrupt 50 Priority"
|
|
hexmask.long.byte 0x30 8.--15. 1. " PRI_49 ,Interrupt 49 Priority"
|
|
hexmask.long.byte 0x30 0.--7. 1. " PRI_48 ,Interrupt 48 Priority"
|
|
line.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hexmask.long.byte 0x34 24.--31. 1. " PRI_55 ,Interrupt 55 Priority"
|
|
hexmask.long.byte 0x34 16.--23. 1. " PRI_54 ,Interrupt 54 Priority"
|
|
hexmask.long.byte 0x34 8.--15. 1. " PRI_53 ,Interrupt 53 Priority"
|
|
hexmask.long.byte 0x34 0.--7. 1. " PRI_52 ,Interrupt 52 Priority"
|
|
line.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hexmask.long.byte 0x38 24.--31. 1. " PRI_59 ,Interrupt 59 Priority"
|
|
hexmask.long.byte 0x38 16.--23. 1. " PRI_58 ,Interrupt 58 Priority"
|
|
hexmask.long.byte 0x38 8.--15. 1. " PRI_57 ,Interrupt 57 Priority"
|
|
hexmask.long.byte 0x38 0.--7. 1. " PRI_56 ,Interrupt 56 Priority"
|
|
line.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hexmask.long.byte 0x3C 24.--31. 1. " PRI_63 ,Interrupt 63 Priority"
|
|
hexmask.long.byte 0x3C 16.--23. 1. " PRI_62 ,Interrupt 62 Priority"
|
|
hexmask.long.byte 0x3C 8.--15. 1. " PRI_61 ,Interrupt 61 Priority"
|
|
hexmask.long.byte 0x3C 0.--7. 1. " PRI_60 ,Interrupt 60 Priority"
|
|
line.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hexmask.long.byte 0x40 24.--31. 1. " PRI_67 ,Interrupt 67 Priority"
|
|
hexmask.long.byte 0x40 16.--23. 1. " PRI_66 ,Interrupt 66 Priority"
|
|
hexmask.long.byte 0x40 8.--15. 1. " PRI_65 ,Interrupt 65 Priority"
|
|
hexmask.long.byte 0x40 0.--7. 1. " PRI_64 ,Interrupt 64 Priority"
|
|
line.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hexmask.long.byte 0x44 24.--31. 1. " PRI_71 ,Interrupt 71 Priority"
|
|
hexmask.long.byte 0x44 16.--23. 1. " PRI_70 ,Interrupt 70 Priority"
|
|
hexmask.long.byte 0x44 8.--15. 1. " PRI_69 ,Interrupt 69 Priority"
|
|
hexmask.long.byte 0x44 0.--7. 1. " PRI_68 ,Interrupt 68 Priority"
|
|
line.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hexmask.long.byte 0x48 24.--31. 1. " PRI_75 ,Interrupt 75 Priority"
|
|
hexmask.long.byte 0x48 16.--23. 1. " PRI_74 ,Interrupt 74 Priority"
|
|
hexmask.long.byte 0x48 8.--15. 1. " PRI_73 ,Interrupt 73 Priority"
|
|
hexmask.long.byte 0x48 0.--7. 1. " PRI_72 ,Interrupt 72 Priority"
|
|
line.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hexmask.long.byte 0x4C 24.--31. 1. " PRI_79 ,Interrupt 79 Priority"
|
|
hexmask.long.byte 0x4C 16.--23. 1. " PRI_78 ,Interrupt 78 Priority"
|
|
hexmask.long.byte 0x4C 8.--15. 1. " PRI_77 ,Interrupt 77 Priority"
|
|
hexmask.long.byte 0x4C 0.--7. 1. " PRI_76 ,Interrupt 76 Priority"
|
|
line.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hexmask.long.byte 0x50 24.--31. 1. " PRI_83 ,Interrupt 83 Priority"
|
|
hexmask.long.byte 0x50 16.--23. 1. " PRI_82 ,Interrupt 82 Priority"
|
|
hexmask.long.byte 0x50 8.--15. 1. " PRI_81 ,Interrupt 81 Priority"
|
|
hexmask.long.byte 0x50 0.--7. 1. " PRI_80 ,Interrupt 80 Priority"
|
|
line.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hexmask.long.byte 0x54 24.--31. 1. " PRI_87 ,Interrupt 87 Priority"
|
|
hexmask.long.byte 0x54 16.--23. 1. " PRI_86 ,Interrupt 86 Priority"
|
|
hexmask.long.byte 0x54 8.--15. 1. " PRI_85 ,Interrupt 85 Priority"
|
|
hexmask.long.byte 0x54 0.--7. 1. " PRI_84 ,Interrupt 84 Priority"
|
|
line.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hexmask.long.byte 0x58 24.--31. 1. " PRI_91 ,Interrupt 91 Priority"
|
|
hexmask.long.byte 0x58 16.--23. 1. " PRI_90 ,Interrupt 90 Priority"
|
|
hexmask.long.byte 0x58 8.--15. 1. " PRI_89 ,Interrupt 89 Priority"
|
|
hexmask.long.byte 0x58 0.--7. 1. " PRI_88 ,Interrupt 88 Priority"
|
|
line.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hexmask.long.byte 0x5C 24.--31. 1. " PRI_95 ,Interrupt 95 Priority"
|
|
hexmask.long.byte 0x5C 16.--23. 1. " PRI_94 ,Interrupt 94 Priority"
|
|
hexmask.long.byte 0x5C 8.--15. 1. " PRI_93 ,Interrupt 93 Priority"
|
|
hexmask.long.byte 0x5C 0.--7. 1. " PRI_92 ,Interrupt 92 Priority"
|
|
line.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hexmask.long.byte 0x60 24.--31. 1. " PRI_99 ,Interrupt 99 Priority"
|
|
hexmask.long.byte 0x60 16.--23. 1. " PRI_98 ,Interrupt 98 Priority"
|
|
hexmask.long.byte 0x60 8.--15. 1. " PRI_97 ,Interrupt 97 Priority"
|
|
hexmask.long.byte 0x60 0.--7. 1. " PRI_96 ,Interrupt 96 Priority"
|
|
line.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hexmask.long.byte 0x64 24.--31. 1. " PRI_103 ,Interrupt 103 Priority"
|
|
hexmask.long.byte 0x64 16.--23. 1. " PRI_102 ,Interrupt 102 Priority"
|
|
hexmask.long.byte 0x64 8.--15. 1. " PRI_101 ,Interrupt 101 Priority"
|
|
hexmask.long.byte 0x64 0.--7. 1. " PRI_100 ,Interrupt 100 Priority"
|
|
line.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hexmask.long.byte 0x68 24.--31. 1. " PRI_107 ,Interrupt 107 Priority"
|
|
hexmask.long.byte 0x68 16.--23. 1. " PRI_106 ,Interrupt 106 Priority"
|
|
hexmask.long.byte 0x68 8.--15. 1. " PRI_105 ,Interrupt 105 Priority"
|
|
hexmask.long.byte 0x68 0.--7. 1. " PRI_104 ,Interrupt 104 Priority"
|
|
line.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hexmask.long.byte 0x6C 24.--31. 1. " PRI_111 ,Interrupt 111 Priority"
|
|
hexmask.long.byte 0x6C 16.--23. 1. " PRI_110 ,Interrupt 110 Priority"
|
|
hexmask.long.byte 0x6C 8.--15. 1. " PRI_109 ,Interrupt 109 Priority"
|
|
hexmask.long.byte 0x6C 0.--7. 1. " PRI_108 ,Interrupt 108 Priority"
|
|
line.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hexmask.long.byte 0x70 24.--31. 1. " PRI_115 ,Interrupt 115 Priority"
|
|
hexmask.long.byte 0x70 16.--23. 1. " PRI_114 ,Interrupt 114 Priority"
|
|
hexmask.long.byte 0x70 8.--15. 1. " PRI_113 ,Interrupt 113 Priority"
|
|
hexmask.long.byte 0x70 0.--7. 1. " PRI_112 ,Interrupt 112 Priority"
|
|
line.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hexmask.long.byte 0x74 24.--31. 1. " PRI_119 ,Interrupt 119 Priority"
|
|
hexmask.long.byte 0x74 16.--23. 1. " PRI_118 ,Interrupt 118 Priority"
|
|
hexmask.long.byte 0x74 8.--15. 1. " PRI_117 ,Interrupt 117 Priority"
|
|
hexmask.long.byte 0x74 0.--7. 1. " PRI_116 ,Interrupt 116 Priority"
|
|
line.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hexmask.long.byte 0x78 24.--31. 1. " PRI_123 ,Interrupt 123 Priority"
|
|
hexmask.long.byte 0x78 16.--23. 1. " PRI_122 ,Interrupt 122 Priority"
|
|
hexmask.long.byte 0x78 8.--15. 1. " PRI_121 ,Interrupt 121 Priority"
|
|
hexmask.long.byte 0x78 0.--7. 1. " PRI_120 ,Interrupt 120 Priority"
|
|
line.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hexmask.long.byte 0x7C 24.--31. 1. " PRI_127 ,Interrupt 127 Priority"
|
|
hexmask.long.byte 0x7C 16.--23. 1. " PRI_126 ,Interrupt 126 Priority"
|
|
hexmask.long.byte 0x7C 8.--15. 1. " PRI_125 ,Interrupt 125 Priority"
|
|
hexmask.long.byte 0x7C 0.--7. 1. " PRI_124 ,Interrupt 124 Priority"
|
|
line.long 0x80 "IPR32,Interrupt Priority Register"
|
|
hexmask.long.byte 0x80 24.--31. 1. " PRI_131 ,Interrupt 131 Priority"
|
|
hexmask.long.byte 0x80 16.--23. 1. " PRI_130 ,Interrupt 130 Priority"
|
|
hexmask.long.byte 0x80 8.--15. 1. " PRI_129 ,Interrupt 129 Priority"
|
|
hexmask.long.byte 0x80 0.--7. 1. " PRI_128 ,Interrupt 128 Priority"
|
|
line.long 0x84 "IPR33,Interrupt Priority Register"
|
|
hexmask.long.byte 0x84 24.--31. 1. " PRI_135 ,Interrupt 135 Priority"
|
|
hexmask.long.byte 0x84 16.--23. 1. " PRI_134 ,Interrupt 134 Priority"
|
|
hexmask.long.byte 0x84 8.--15. 1. " PRI_133 ,Interrupt 133 Priority"
|
|
hexmask.long.byte 0x84 0.--7. 1. " PRI_132 ,Interrupt 132 Priority"
|
|
line.long 0x88 "IPR34,Interrupt Priority Register"
|
|
hexmask.long.byte 0x88 24.--31. 1. " PRI_139 ,Interrupt 139 Priority"
|
|
hexmask.long.byte 0x88 16.--23. 1. " PRI_138 ,Interrupt 138 Priority"
|
|
hexmask.long.byte 0x88 8.--15. 1. " PRI_137 ,Interrupt 137 Priority"
|
|
hexmask.long.byte 0x88 0.--7. 1. " PRI_136 ,Interrupt 136 Priority"
|
|
line.long 0x8C "IPR35,Interrupt Priority Register"
|
|
hexmask.long.byte 0x8C 24.--31. 1. " PRI_143 ,Interrupt 143 Priority"
|
|
hexmask.long.byte 0x8C 16.--23. 1. " PRI_142 ,Interrupt 142 Priority"
|
|
hexmask.long.byte 0x8C 8.--15. 1. " PRI_141 ,Interrupt 141 Priority"
|
|
hexmask.long.byte 0x8C 0.--7. 1. " PRI_140 ,Interrupt 140 Priority"
|
|
line.long 0x90 "IPR36,Interrupt Priority Register"
|
|
hexmask.long.byte 0x90 24.--31. 1. " PRI_147 ,Interrupt 147 Priority"
|
|
hexmask.long.byte 0x90 16.--23. 1. " PRI_146 ,Interrupt 146 Priority"
|
|
hexmask.long.byte 0x90 8.--15. 1. " PRI_145 ,Interrupt 145 Priority"
|
|
hexmask.long.byte 0x90 0.--7. 1. " PRI_144 ,Interrupt 144 Priority"
|
|
line.long 0x94 "IPR37,Interrupt Priority Register"
|
|
hexmask.long.byte 0x94 24.--31. 1. " PRI_151 ,Interrupt 151 Priority"
|
|
hexmask.long.byte 0x94 16.--23. 1. " PRI_150 ,Interrupt 150 Priority"
|
|
hexmask.long.byte 0x94 8.--15. 1. " PRI_149 ,Interrupt 149 Priority"
|
|
hexmask.long.byte 0x94 0.--7. 1. " PRI_148 ,Interrupt 148 Priority"
|
|
line.long 0x98 "IPR38,Interrupt Priority Register"
|
|
hexmask.long.byte 0x98 24.--31. 1. " PRI_155 ,Interrupt 155 Priority"
|
|
hexmask.long.byte 0x98 16.--23. 1. " PRI_154 ,Interrupt 154 Priority"
|
|
hexmask.long.byte 0x98 8.--15. 1. " PRI_153 ,Interrupt 153 Priority"
|
|
hexmask.long.byte 0x98 0.--7. 1. " PRI_152 ,Interrupt 152 Priority"
|
|
line.long 0x9C "IPR39,Interrupt Priority Register"
|
|
hexmask.long.byte 0x9C 24.--31. 1. " PRI_159 ,Interrupt 159 Priority"
|
|
hexmask.long.byte 0x9C 16.--23. 1. " PRI_158 ,Interrupt 158 Priority"
|
|
hexmask.long.byte 0x9C 8.--15. 1. " PRI_157 ,Interrupt 157 Priority"
|
|
hexmask.long.byte 0x9C 0.--7. 1. " PRI_156 ,Interrupt 156 Priority"
|
|
line.long 0xA0 "IPR40,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA0 24.--31. 1. " PRI_163 ,Interrupt 163 Priority"
|
|
hexmask.long.byte 0xA0 16.--23. 1. " PRI_162 ,Interrupt 162 Priority"
|
|
hexmask.long.byte 0xA0 8.--15. 1. " PRI_161 ,Interrupt 161 Priority"
|
|
hexmask.long.byte 0xA0 0.--7. 1. " PRI_160 ,Interrupt 160 Priority"
|
|
line.long 0xA4 "IPR41,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA4 24.--31. 1. " PRI_167 ,Interrupt 167 Priority"
|
|
hexmask.long.byte 0xA4 16.--23. 1. " PRI_166 ,Interrupt 166 Priority"
|
|
hexmask.long.byte 0xA4 8.--15. 1. " PRI_165 ,Interrupt 165 Priority"
|
|
hexmask.long.byte 0xA4 0.--7. 1. " PRI_164 ,Interrupt 164 Priority"
|
|
line.long 0xA8 "IPR42,Interrupt Priority Register"
|
|
hexmask.long.byte 0xA8 24.--31. 1. " PRI_171 ,Interrupt 171 Priority"
|
|
hexmask.long.byte 0xA8 16.--23. 1. " PRI_170 ,Interrupt 170 Priority"
|
|
hexmask.long.byte 0xA8 8.--15. 1. " PRI_169 ,Interrupt 169 Priority"
|
|
hexmask.long.byte 0xA8 0.--7. 1. " PRI_168 ,Interrupt 168 Priority"
|
|
line.long 0xAC "IPR43,Interrupt Priority Register"
|
|
hexmask.long.byte 0xAC 24.--31. 1. " PRI_175 ,Interrupt 175 Priority"
|
|
hexmask.long.byte 0xAC 16.--23. 1. " PRI_174 ,Interrupt 174 Priority"
|
|
hexmask.long.byte 0xAC 8.--15. 1. " PRI_173 ,Interrupt 173 Priority"
|
|
hexmask.long.byte 0xAC 0.--7. 1. " PRI_172 ,Interrupt 172 Priority"
|
|
line.long 0xB0 "IPR44,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB0 24.--31. 1. " PRI_179 ,Interrupt 179 Priority"
|
|
hexmask.long.byte 0xB0 16.--23. 1. " PRI_178 ,Interrupt 178 Priority"
|
|
hexmask.long.byte 0xB0 8.--15. 1. " PRI_177 ,Interrupt 177 Priority"
|
|
hexmask.long.byte 0xB0 0.--7. 1. " PRI_176 ,Interrupt 176 Priority"
|
|
line.long 0xB4 "IPR45,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB4 24.--31. 1. " PRI_183 ,Interrupt 183 Priority"
|
|
hexmask.long.byte 0xB4 16.--23. 1. " PRI_182 ,Interrupt 182 Priority"
|
|
hexmask.long.byte 0xB4 8.--15. 1. " PRI_181 ,Interrupt 181 Priority"
|
|
hexmask.long.byte 0xB4 0.--7. 1. " PRI_180 ,Interrupt 180 Priority"
|
|
line.long 0xB8 "IPR46,Interrupt Priority Register"
|
|
hexmask.long.byte 0xB8 24.--31. 1. " PRI_187 ,Interrupt 187 Priority"
|
|
hexmask.long.byte 0xB8 16.--23. 1. " PRI_186 ,Interrupt 186 Priority"
|
|
hexmask.long.byte 0xB8 8.--15. 1. " PRI_185 ,Interrupt 185 Priority"
|
|
hexmask.long.byte 0xB8 0.--7. 1. " PRI_184 ,Interrupt 184 Priority"
|
|
line.long 0xBC "IPR47,Interrupt Priority Register"
|
|
hexmask.long.byte 0xBC 24.--31. 1. " PRI_191 ,Interrupt 191 Priority"
|
|
hexmask.long.byte 0xBC 16.--23. 1. " PRI_190 ,Interrupt 190 Priority"
|
|
hexmask.long.byte 0xBC 8.--15. 1. " PRI_189 ,Interrupt 189 Priority"
|
|
hexmask.long.byte 0xBC 0.--7. 1. " PRI_188 ,Interrupt 188 Priority"
|
|
line.long 0xC0 "IPR48,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC0 24.--31. 1. " PRI_195 ,Interrupt 195 Priority"
|
|
hexmask.long.byte 0xC0 16.--23. 1. " PRI_194 ,Interrupt 194 Priority"
|
|
hexmask.long.byte 0xC0 8.--15. 1. " PRI_193 ,Interrupt 193 Priority"
|
|
hexmask.long.byte 0xC0 0.--7. 1. " PRI_192 ,Interrupt 192 Priority"
|
|
line.long 0xC4 "IPR49,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC4 24.--31. 1. " PRI_199 ,Interrupt 199 Priority"
|
|
hexmask.long.byte 0xC4 16.--23. 1. " PRI_198 ,Interrupt 198 Priority"
|
|
hexmask.long.byte 0xC4 8.--15. 1. " PRI_197 ,Interrupt 197 Priority"
|
|
hexmask.long.byte 0xC4 0.--7. 1. " PRI_196 ,Interrupt 196 Priority"
|
|
line.long 0xC8 "IPR50,Interrupt Priority Register"
|
|
hexmask.long.byte 0xC8 24.--31. 1. " PRI_203 ,Interrupt 203 Priority"
|
|
hexmask.long.byte 0xC8 16.--23. 1. " PRI_202 ,Interrupt 202 Priority"
|
|
hexmask.long.byte 0xC8 8.--15. 1. " PRI_201 ,Interrupt 201 Priority"
|
|
hexmask.long.byte 0xC8 0.--7. 1. " PRI_200 ,Interrupt 200 Priority"
|
|
line.long 0xCC "IPR51,Interrupt Priority Register"
|
|
hexmask.long.byte 0xCC 24.--31. 1. " PRI_207 ,Interrupt 207 Priority"
|
|
hexmask.long.byte 0xCC 16.--23. 1. " PRI_206 ,Interrupt 206 Priority"
|
|
hexmask.long.byte 0xCC 8.--15. 1. " PRI_205 ,Interrupt 205 Priority"
|
|
hexmask.long.byte 0xCC 0.--7. 1. " PRI_204 ,Interrupt 204 Priority"
|
|
line.long 0xD0 "IPR52,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD0 24.--31. 1. " PRI_211 ,Interrupt 211 Priority"
|
|
hexmask.long.byte 0xD0 16.--23. 1. " PRI_210 ,Interrupt 210 Priority"
|
|
hexmask.long.byte 0xD0 8.--15. 1. " PRI_209 ,Interrupt 209 Priority"
|
|
hexmask.long.byte 0xD0 0.--7. 1. " PRI_208 ,Interrupt 208 Priority"
|
|
line.long 0xD4 "IPR53,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD4 24.--31. 1. " PRI_215 ,Interrupt 215 Priority"
|
|
hexmask.long.byte 0xD4 16.--23. 1. " PRI_214 ,Interrupt 214 Priority"
|
|
hexmask.long.byte 0xD4 8.--15. 1. " PRI_213 ,Interrupt 213 Priority"
|
|
hexmask.long.byte 0xD4 0.--7. 1. " PRI_212 ,Interrupt 212 Priority"
|
|
line.long 0xD8 "IPR54,Interrupt Priority Register"
|
|
hexmask.long.byte 0xD8 24.--31. 1. " PRI_219 ,Interrupt 219 Priority"
|
|
hexmask.long.byte 0xD8 16.--23. 1. " PRI_218 ,Interrupt 218 Priority"
|
|
hexmask.long.byte 0xD8 8.--15. 1. " PRI_217 ,Interrupt 217 Priority"
|
|
hexmask.long.byte 0xD8 0.--7. 1. " PRI_216 ,Interrupt 216 Priority"
|
|
line.long 0xDC "IPR55,Interrupt Priority Register"
|
|
hexmask.long.byte 0xDC 24.--31. 1. " PRI_223 ,Interrupt 223 Priority"
|
|
hexmask.long.byte 0xDC 16.--23. 1. " PRI_222 ,Interrupt 222 Priority"
|
|
hexmask.long.byte 0xDC 8.--15. 1. " PRI_221 ,Interrupt 221 Priority"
|
|
hexmask.long.byte 0xDC 0.--7. 1. " PRI_220 ,Interrupt 220 Priority"
|
|
line.long 0xE0 "IPR56,Interrupt Priority Register"
|
|
hexmask.long.byte 0xE0 24.--31. 1. " PRI_227 ,Interrupt 227 Priority"
|
|
hexmask.long.byte 0xE0 16.--23. 1. " PRI_226 ,Interrupt 226 Priority"
|
|
hexmask.long.byte 0xE0 8.--15. 1. " PRI_225 ,Interrupt 225 Priority"
|
|
hexmask.long.byte 0xE0 0.--7. 1. " PRI_224 ,Interrupt 224 Priority"
|
|
line.long 0xE4 "IPR57,Interrupt Priority Register"
|
|
hexmask.long.byte 0xE4 24.--31. 1. " PRI_231 ,Interrupt 231 Priority"
|
|
hexmask.long.byte 0xE4 16.--23. 1. " PRI_230 ,Interrupt 230 Priority"
|
|
hexmask.long.byte 0xE4 8.--15. 1. " PRI_229 ,Interrupt 229 Priority"
|
|
hexmask.long.byte 0xE4 0.--7. 1. " PRI_228 ,Interrupt 228 Priority"
|
|
line.long 0xE8 "IPR58,Interrupt Priority Register"
|
|
hexmask.long.byte 0xE8 24.--31. 1. " PRI_235 ,Interrupt 235 Priority"
|
|
hexmask.long.byte 0xE8 16.--23. 1. " PRI_234 ,Interrupt 234 Priority"
|
|
hexmask.long.byte 0xE8 8.--15. 1. " PRI_233 ,Interrupt 233 Priority"
|
|
hexmask.long.byte 0xE8 0.--7. 1. " PRI_232 ,Interrupt 232 Priority"
|
|
line.long 0xEC "IPR59,Interrupt Priority Register"
|
|
hexmask.long.byte 0xEC 24.--31. 1. " PRI_239 ,Interrupt 239 Priority"
|
|
hexmask.long.byte 0xEC 16.--23. 1. " PRI_238 ,Interrupt 238 Priority"
|
|
hexmask.long.byte 0xEC 8.--15. 1. " PRI_237 ,Interrupt 237 Priority"
|
|
hexmask.long.byte 0xEC 0.--7. 1. " PRI_236 ,Interrupt 236 Priority"
|
|
else
|
|
hgroup.long 0x400++0xEF
|
|
hide.long 0x0 "IPR0,Interrupt Priority Register"
|
|
hide.long 0x4 "IPR1,Interrupt Priority Register"
|
|
hide.long 0x8 "IPR2,Interrupt Priority Register"
|
|
hide.long 0xC "IPR3,Interrupt Priority Register"
|
|
hide.long 0x10 "IPR4,Interrupt Priority Register"
|
|
hide.long 0x14 "IPR5,Interrupt Priority Register"
|
|
hide.long 0x18 "IPR6,Interrupt Priority Register"
|
|
hide.long 0x1C "IPR7,Interrupt Priority Register"
|
|
hide.long 0x20 "IPR8,Interrupt Priority Register"
|
|
hide.long 0x24 "IPR9,Interrupt Priority Register"
|
|
hide.long 0x28 "IPR10,Interrupt Priority Register"
|
|
hide.long 0x2C "IPR11,Interrupt Priority Register"
|
|
hide.long 0x30 "IPR12,Interrupt Priority Register"
|
|
hide.long 0x34 "IPR13,Interrupt Priority Register"
|
|
hide.long 0x38 "IPR14,Interrupt Priority Register"
|
|
hide.long 0x3C "IPR15,Interrupt Priority Register"
|
|
hide.long 0x40 "IPR16,Interrupt Priority Register"
|
|
hide.long 0x44 "IPR17,Interrupt Priority Register"
|
|
hide.long 0x48 "IPR18,Interrupt Priority Register"
|
|
hide.long 0x4C "IPR19,Interrupt Priority Register"
|
|
hide.long 0x50 "IPR20,Interrupt Priority Register"
|
|
hide.long 0x54 "IPR21,Interrupt Priority Register"
|
|
hide.long 0x58 "IPR22,Interrupt Priority Register"
|
|
hide.long 0x5C "IPR23,Interrupt Priority Register"
|
|
hide.long 0x60 "IPR24,Interrupt Priority Register"
|
|
hide.long 0x64 "IPR25,Interrupt Priority Register"
|
|
hide.long 0x68 "IPR26,Interrupt Priority Register"
|
|
hide.long 0x6C "IPR27,Interrupt Priority Register"
|
|
hide.long 0x70 "IPR28,Interrupt Priority Register"
|
|
hide.long 0x74 "IPR29,Interrupt Priority Register"
|
|
hide.long 0x78 "IPR30,Interrupt Priority Register"
|
|
hide.long 0x7C "IPR31,Interrupt Priority Register"
|
|
hide.long 0x80 "IPR32,Interrupt Priority Register"
|
|
hide.long 0x84 "IPR33,Interrupt Priority Register"
|
|
hide.long 0x88 "IPR34,Interrupt Priority Register"
|
|
hide.long 0x8C "IPR35,Interrupt Priority Register"
|
|
hide.long 0x90 "IPR36,Interrupt Priority Register"
|
|
hide.long 0x94 "IPR37,Interrupt Priority Register"
|
|
hide.long 0x98 "IPR38,Interrupt Priority Register"
|
|
hide.long 0x9C "IPR39,Interrupt Priority Register"
|
|
hide.long 0xA0 "IPR40,Interrupt Priority Register"
|
|
hide.long 0xA4 "IPR41,Interrupt Priority Register"
|
|
hide.long 0xA8 "IPR42,Interrupt Priority Register"
|
|
hide.long 0xAC "IPR43,Interrupt Priority Register"
|
|
hide.long 0xB0 "IPR44,Interrupt Priority Register"
|
|
hide.long 0xB4 "IPR45,Interrupt Priority Register"
|
|
hide.long 0xB8 "IPR46,Interrupt Priority Register"
|
|
hide.long 0xBC "IPR47,Interrupt Priority Register"
|
|
hide.long 0xC0 "IPR48,Interrupt Priority Register"
|
|
hide.long 0xC4 "IPR49,Interrupt Priority Register"
|
|
hide.long 0xC8 "IPR50,Interrupt Priority Register"
|
|
hide.long 0xCC "IPR51,Interrupt Priority Register"
|
|
hide.long 0xD0 "IPR52,Interrupt Priority Register"
|
|
hide.long 0xD4 "IPR53,Interrupt Priority Register"
|
|
hide.long 0xD8 "IPR54,Interrupt Priority Register"
|
|
hide.long 0xDC "IPR55,Interrupt Priority Register"
|
|
hide.long 0xE0 "IPR56,Interrupt Priority Register"
|
|
hide.long 0xE4 "IPR57,Interrupt Priority Register"
|
|
hide.long 0xE8 "IPR58,Interrupt Priority Register"
|
|
hide.long 0xEC "IPR59,Interrupt Priority Register"
|
|
endif
|
|
tree.end
|
|
width 0x0b
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Debug"
|
|
tree "Core Debug"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 7.
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x20001)==0x20000)
|
|
group 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core running and Lockup/Debug Key" "Not running,Running"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core is sleeping/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register Read/Write on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked"
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x20001)==0x20001)
|
|
group 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core running and Lockup/Debug Key" "Not running,Running"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core is sleeping/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register Read/Write on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 5. " C_SNAPSTALL ,Halting debug to gain control of the core" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 2. " C_STEP ,Core Step" "No step,Step"
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x20001)==0x0)
|
|
group 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core running and Lockup/Debug Key" "Not running,Running"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core is sleeping/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register Read/Write on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
elif (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x20001)==0x00001)
|
|
group 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core running and Lockup/Debug Key" "Not running,Running"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core is sleeping/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register Read/Write on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 2. " C_STEP ,Core Step" "No step,Step"
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
endif
|
|
wgroup 0xDF4++0x03
|
|
line.long 0x00 "DCRSR,Debug Core Register Selector Register"
|
|
bitfld.long 0x00 16. " REGWNR ,Register Read/Write" "Read,Write"
|
|
bitfld.long 0x00 0.--4. " REGSEL ,Register Selection" "R0,R1,R2,R3,R4,R5,R6,R7,R8,R9,R10,R11,R12,R13,R14,R15,xPSR/ Flags,MSP,PSP,RAZ/WI,CONTROL/FAULTMASK/BASEPRI/PRIMASK,?..."
|
|
group 0xDF8++0x03
|
|
line.long 0x00 "DCRDR,Debug Core Register Data Register"
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDFC))&0x10000)==0x10000)
|
|
group.long 0xDFC++0x03
|
|
line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register"
|
|
bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1"
|
|
bitfld.long 0x00 18. " MON_STEP ,Setting this bit to 1 makes the step request pending" "No step,Step"
|
|
textline " "
|
|
bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending"
|
|
bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled"
|
|
else
|
|
group.long 0xDFC++0x03
|
|
line.long 0x00 "DEMCR,Debug Exception and Monitor Control Register"
|
|
bitfld.long 0x00 24. " TRCENA ,Global enable for all DWT and ITM features" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " MON_REQ ,DebugMonitor semaphore bit" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " MON_PEND ,Sets or clears the pending state of the DebugMonitor exception" "Not pending,Pending"
|
|
bitfld.long 0x00 16. " MON_EN ,Enable the DebugMonitor exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " VC_HARDERR ,Enable halting debug trap on a HardFault exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " VC_INTERR ,Enable halting debug trap" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " VC_BUSERR ,Enable halting debug trap on a BusFault exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " VC_STATERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " VC_CHKERR ,Enable halting debug trap on a UsageFault exception" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " VC_NOCPERR ,Enable halting debug trap on a UsageFault caused by an access to a Coprocessor" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " VC_MMERR ,Enable halting debug trap on a MemManage exception" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " VC_CORERESET ,Enable Reset Vector Catch" "Disabled,Enabled"
|
|
endif
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Flash Patch and Breakpoint Unit (FPB)"
|
|
sif COMPonent.AVAILABLE("FPB")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("FPB",-1))
|
|
width 10.
|
|
group 0x00--0x27
|
|
line.long 0x00 "FP_CTRL,Flash Patch Control Register"
|
|
bitfld.long 0x00 8.--11. " NUM_LIT ,Number of Literal Slots Field" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 4.--7. " NUM_CODE ,Number of Code Slots Field" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 1. " KEY ,Key Field" "Low,High"
|
|
bitfld.long 0x00 0. " ENABLE ,Flash Patch Unit Enable" "Disabled,Enabled"
|
|
;group 0x04++0x03
|
|
line.long 0x04 "FP_REMAP,Flash Patch Remap Register"
|
|
hexmask.long.tbyte 0x04 5.--28. 1. " REMAP ,Remap Base Address Field"
|
|
;group 0x08++0x03
|
|
line.long 0x8 "FP_COMP0,Flash Patch Comparator Register 0"
|
|
bitfld.long 0x8 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x8 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x8 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0xC "FP_COMP1,Flash Patch Comparator Register 1"
|
|
bitfld.long 0xC 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0xC 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0xC 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x10 "FP_COMP2,Flash Patch Comparator Register 2"
|
|
bitfld.long 0x10 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x10 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x10 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x14 "FP_COMP3,Flash Patch Comparator Register 3"
|
|
bitfld.long 0x14 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x14 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x14 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x18 "FP_COMP4,Flash Patch Comparator Register 4"
|
|
bitfld.long 0x18 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x18 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x18 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x1C "FP_COMP5,Flash Patch Comparator Register 5"
|
|
bitfld.long 0x1C 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x1C 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x1C 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x20 "FP_COMP6,Flash Patch Comparator Register 6"
|
|
bitfld.long 0x20 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x20 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x20 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
line.long 0x24 "FP_COMP7,Flash Patch Comparator Register 7"
|
|
bitfld.long 0x24 30.--31. " REPLACE ,REPLACE" "Remap to remap address,Set BKPT on lower halfword,Set BKPT on upper halfword,Set BKPT on both"
|
|
hexmask.long 0x24 2.--28. 1. " COMP ,Comparison Address"
|
|
bitfld.long 0x24 0. " ENABLE ,Compare and Remap Enable" "Disabled,Enabled"
|
|
tree "Coresight Management Registers"
|
|
rgroup 0xfd0--0xfff
|
|
line.long 0x00 "PID4,Peripheral ID4"
|
|
line.long 0x04 "PID5,Peripheral ID5"
|
|
line.long 0x08 "PID6,Peripheral ID6"
|
|
line.long 0x0c "PID7,Peripheral ID7"
|
|
line.long 0x10 "PID0,Peripheral ID0"
|
|
line.long 0x14 "PID1,Peripheral ID1"
|
|
line.long 0x18 "PID2,Peripheral ID2"
|
|
line.long 0x1c "PID3,Peripheral ID3"
|
|
line.long 0x20 "CID0,Component ID0"
|
|
line.long 0x24 "CID1,Component ID1"
|
|
line.long 0x28 "CID2,Component ID2"
|
|
line.long 0x2c "CID3,Component ID3"
|
|
tree.end
|
|
else
|
|
newline
|
|
textline "FPB component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Data Watchpoint and Trace Unit (DWT)"
|
|
sif COMPonent.AVAILABLE("DWT")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))
|
|
width 15.
|
|
group 0x00--0x1B
|
|
line.long 0x00 "DWT_CTRL,DWT Control Register"
|
|
bitfld.long 0x00 28.--31. " NUMCOMP ,Number of Comparators Field" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 22. " CYCEVTENA ,Enables Cycle Count Event" "Disabled,Enabled"
|
|
bitfld.long 0x00 21. " FOLDEVTENA ,Enables Folded Instruction Count Event" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " LSUEVTENA ,Enables LSU Count Event" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " SLEEPEVTENA ,Enables Sleep Count Event" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " EXCEVTENA ,Enables Interrupt Overhead Event" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " CPIEVTENA ,Enables CPI Count Event" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " EXCTRCENA ,Enables Interrupt Event Tracing" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PCSAMPLEENA ,Enables PC Sampling Event" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " SYNCTAP ,Feed Synchronization Pulse to the ITM SYNCEN Control" "Disabled,24,26,28"
|
|
bitfld.long 0x00 9. " CYCTAP ,Selects a Tap on the DWT_CYCCNT Register" "Bit 6,Bit 10"
|
|
bitfld.long 0x00 5.--8. " POSTCNT ,Post-Scalar Counter for CYCTAP" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 1.--4. " POSTPRESET ,Reload Value for POSTCNT Post-Scalar Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 0. " CYCCNTENA ,Enable the DWT_CYCCNT Counter" "Disabled,Enabled"
|
|
;group 0x04++0x03
|
|
line.long 0x04 "DWT_CYCCNT,Cycle Count register"
|
|
;group 0x08++0x03
|
|
line.long 0x08 "DWT_CPICNT,DWT CPI Count Register"
|
|
hexmask.long.byte 0x08 0.--7. 1. " CPICNT ,The base CPI counter"
|
|
;group 0x0c++0x03
|
|
line.long 0x0c "DWT_EXCCNT,DWT Exception Overhead Count Register"
|
|
hexmask.long.byte 0x0c 0.--7. 1. " EXCCNT ,The exception overhead counter"
|
|
;group 0x10++0x03
|
|
line.long 0x10 "DWT_SLEEPCNT,DWT Sleep Count Register"
|
|
hexmask.long.byte 0x10 0.--7. 1. " SLEEPCNT ,Sleep Counter"
|
|
;group 0x14++0x03
|
|
line.long 0x14 "DWT_LSUCNT,DWT LSU Count Register"
|
|
hexmask.long.byte 0x14 0.--7. 1. " LSUCNT ,Load-store counter"
|
|
;group 0x18++0x03
|
|
line.long 0x18 "DWT_FOLDCNT,DWT Fold Count Register"
|
|
hexmask.long.byte 0x18 0.--7. 1. " FOLDCNT ,Folded-instruction counter"
|
|
group.long 0x20++0x03
|
|
line.long 0x00 "DWT_COMP0,DWT Comparator Register 0"
|
|
group.long 0x30++0x03
|
|
line.long 0x00 "DWT_COMP1,DWT Comparator Register 1"
|
|
group.long 0x40++0x03
|
|
line.long 0x00 "DWT_COMP2,DWT Comparator Register 2"
|
|
group.long 0x50++0x03
|
|
line.long 0x00 "DWT_COMP3,DWT Comparator Register 3"
|
|
group.long 0x24++0x03
|
|
line.long 0x00 "DWT_MASK0,DWT Mask Registers 0"
|
|
bitfld.long 0x00 0.--3. " MASK ,Mask on Data Address when Matching Against COMP" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group.long 0x34++0x03
|
|
line.long 0x00 "DWT_MASK1,DWT Mask Registers 1"
|
|
bitfld.long 0x00 0.--3. " MASK ,Mask on Data Address when Matching Against COMP" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group.long 0x44++0x03
|
|
line.long 0x00 "DWT_MASK2,DWT Mask Registers 2"
|
|
bitfld.long 0x00 0.--3. " MASK ,Mask on Data Address when Matching Against COMP" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group.long 0x54++0x03
|
|
line.long 0x00 "DWT_MASK3,DWT Mask Registers 3"
|
|
bitfld.long 0x00 0.--3. " MASK ,Mask on Data Address when Matching Against COMP" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x28))&0x20)==0x00)
|
|
group.long 0x28++0x03
|
|
line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Sample and emit PC through ITM,Emit data through ITM,Sample PC and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
else
|
|
group.long 0x28++0x03
|
|
line.long 0x00 "DWT_FUNCTION0,DWT Function Registers 0"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Emit address offset through ITM,Emit data and address offset through ITM,Emit address offset and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
endif
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x38))&0x20)==0x00)
|
|
group.long 0x38++0x03
|
|
line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Sample and emit PC through ITM,Emit data through ITM,Sample PC and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
else
|
|
group.long 0x38++0x03
|
|
line.long 0x00 "DWT_FUNCTION1,DWT Function Registers 1"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Emit address offset through ITM,Emit data and address offset through ITM,Emit address offset and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
endif
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x48))&0x20)==0x00)
|
|
group.long 0x48++0x03
|
|
line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Sample and emit PC through ITM,Emit data through ITM,Sample PC and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
else
|
|
group.long 0x48++0x03
|
|
line.long 0x00 "DWT_FUNCTION2,DWT Function Registers 2"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Emit address offset through ITM,Emit data and address offset through ITM,Emit address offset and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
endif
|
|
if (((per.long(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))+0x58))&0x20)==0x00)
|
|
group.long 0x58++0x03
|
|
line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Sample and emit PC through ITM,Emit data through ITM,Sample PC and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
else
|
|
group.long 0x58++0x03
|
|
line.long 0x00 "DWT_FUNCTION3,DWT Function Registers 3"
|
|
bitfld.long 0x00 16.--19. " DATAVADDR1 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 12.--15. " DATAVADDR0 ,Data Value Comparator ID" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 10.--11. " DATAVSIZE ,Data Value Size" "byte,half,word,res"
|
|
bitfld.long 0x00 9. " LNK1ENA ,DATAVADDR1 support" "Not Supported,Supported"
|
|
bitfld.long 0x00 8. " DATAVMATCH ,Data value compare" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " CYCMATCH ,Comparator Compares Against the PC Sampler Counter" "Cleared,Set"
|
|
bitfld.long 0x00 5. " EMITRANGE ,Emit Range Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " FUNCTION ,FUNCTION settings" "Disabled,Emit address offset through ITM,Emit data and address offset through ITM,Emit address offset and data value through ITM,Watchpoint on PC match,Watchpoint on read,Watchpoint on write,Watchpoint on read or write,ETM trigger on PC match,ETM trigger on read,ETM trigger on write,ETM trigger on read or write,?..."
|
|
endif
|
|
tree "Coresight Management Registers"
|
|
rgroup 0xfd0--0xfff
|
|
line.long 0x00 "PID4,Peripheral ID4"
|
|
line.long 0x04 "PID5,Peripheral ID5"
|
|
line.long 0x08 "PID6,Peripheral ID6"
|
|
line.long 0x0c "PID7,Peripheral ID7"
|
|
line.long 0x10 "PID0,Peripheral ID1"
|
|
line.long 0x14 "PID1,Peripheral ID2"
|
|
line.long 0x18 "PID2,Peripheral ID3"
|
|
line.long 0x1c "PID3,Peripheral ID4"
|
|
line.long 0x20 "CID0,Component ID0"
|
|
line.long 0x24 "CID1,Component ID1"
|
|
line.long 0x28 "CID2,Component ID2"
|
|
line.long 0x2c "CID3,Component ID3"
|
|
tree.end
|
|
else
|
|
newline
|
|
textline "DWT component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree.end
|
|
AUTOINDENT.POP
|
|
tree.end
|
|
tree "ADC (Analog Digital Converter)"
|
|
base ad:0x0
|
|
tree "ADC1 (12-bit Analog Digital Converter)"
|
|
base ad:0x40000000
|
|
group.long 0x178++0x3
|
|
line.long 0x0 "CALAI1,Calibration Setting for Analog Input 1"
|
|
hexmask.long.word 0x0 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0x18C++0x37
|
|
line.long 0x0 "CALAI11,Calibration Setting for Analog Input 11"
|
|
hexmask.long.word 0x0 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x4 "CALAI13,Calibration Setting for Analog Input 13"
|
|
hexmask.long.word 0x4 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x4 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x8 "CALAI15,Calibration Setting for Analog Input 15"
|
|
hexmask.long.word 0x8 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x8 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0xC "CALAI16,Calibration Setting for Analog Input 16"
|
|
hexmask.long.word 0xC 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0xC 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x10 "CALAI17,Calibration Setting for Analog Input 17"
|
|
hexmask.long.word 0x10 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x10 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x14 "CALAI18,Calibration Setting for Analog Input 18"
|
|
hexmask.long.word 0x14 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x14 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x18 "CALAI19,Calibration Setting for Analog Input 19"
|
|
hexmask.long.word 0x18 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x18 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x1C "CALAI20,Calibration Setting for Analog Input 20"
|
|
hexmask.long.word 0x1C 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x1C 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x20 "CALAI21,Calibration Setting for Analog Input 21"
|
|
hexmask.long.word 0x20 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x20 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x24 "CALAI22,Calibration Setting for Analog Input 22"
|
|
hexmask.long.word 0x24 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x24 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x28 "CALAI23,Calibration Setting for Analog Input 23"
|
|
hexmask.long.word 0x28 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x28 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x2C "CALAI24,Calibration Setting for Analog Input 24"
|
|
hexmask.long.word 0x2C 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x2C 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x30 "CALAI25,Calibration Setting for Analog Input 25"
|
|
hexmask.long.word 0x30 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x30 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x34 "CALAI26,Calibration Setting for Analog Input 26"
|
|
hexmask.long.word 0x34 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x34 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0x17C++0xF
|
|
line.long 0x0 "CALAI3,Calibration Setting for Analog Input 3"
|
|
hexmask.long.word 0x0 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x4 "CALAI5,Calibration Setting for Analog Input 5"
|
|
hexmask.long.word 0x4 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x4 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x8 "CALAI7,Calibration Setting for Analog Input 7"
|
|
hexmask.long.word 0x8 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x8 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0xC "CALAI9,Calibration Setting for Analog Input 9"
|
|
hexmask.long.word 0xC 16.--25. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0xC 0.--5. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0xA8++0x7
|
|
line.long 0x0 "CALEN,Calibration Enable"
|
|
bitfld.long 0x0 26. "CALEN26,Channel 26 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 25. "CALEN25,Channel 25 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 24. "CALEN24,Channel 24 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 23. "CALEN23,Channel 23 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 22. "CALEN22,Channel 22 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 21. "CALEN21,Channel 21 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 20. "CALEN20,Channel 20 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 19. "CALEN19,Channel 19 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 18. "CALEN18,Channel 18 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 17. "CALEN17,Channel 17 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 16. "CALEN16,Channel 16 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 15. "CALEN15,Channel 15 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 14. "CALEN14,Channel 14 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 13. "CALEN13,Channel 13 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 12. "CALEN12,Channel 12 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 11. "CALEN11,Channel 11 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 10. "CALEN10,Channel 10 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 9. "CALEN9,Channel 9 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 8. "CALEN8,Channel 8 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 7. "CALEN7,Channel 7 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 6. "CALEN6,Channel 6 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 5. "CALEN5,Channel 5 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "CALEN4,Channel 4 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 3. "CALEN3,Channel 3 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "CALEN2,Channel 2 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 1. "CALEN1,Channel 1 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "CALEN0,Channel 0 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
line.long 0x4 "CALPEN,Calibration Protection Enable"
|
|
bitfld.long 0x4 26. "CALPEN26,Channel 26 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 25. "CALPEN25,Channel 25 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 24. "CALPEN24,Channel 24 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 23. "CALPEN23,Channel 23 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 22. "CALPEN22,Channel 22 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 21. "CALPEN21,Channel 21 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 20. "CALPEN20,Channel 20 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 19. "CALPEN19,Channel 19 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 18. "CALPEN18,Channel 18 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 17. "CALPEN17,Channel 17 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 16. "CALPEN16,Channel 16 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 15. "CALPEN15,Channel 15 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 14. "CALPEN14,Channel 14 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 13. "CALPEN13,Channel 13 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 12. "CALPEN12,Channel 12 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 11. "CALPEN11,Channel 11 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 10. "CALPEN10,Channel 10 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 9. "CALPEN9,Channel 9 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 8. "CALPEN8,Channel 8 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 7. "CALPEN7,Channel 7 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 6. "CALPEN6,Channel 6 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 5. "CALPEN5,Channel 5 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 4. "CALPEN4,Channel 4 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 3. "CALPEN3,Channel 3 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 2. "CALPEN2,Channel 2 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 1. "CALPEN1,Channel 1 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "CALPEN0,Channel 0 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
group.long 0x3C++0x7
|
|
line.long 0x0 "CHCFG0,Channel Configuration Register"
|
|
bitfld.long 0x0 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x0 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x0 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x4 "CHCFG1,Channel Configuration Register"
|
|
bitfld.long 0x4 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x4 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x4 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x4 0.--4. 1. "INSEL,ADC Input Selection"
|
|
group.long 0x64++0x27
|
|
line.long 0x0 "CHCFG10,Channel Configuration Register"
|
|
bitfld.long 0x0 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x0 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x0 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x4 "CHCFG11,Channel Configuration Register"
|
|
bitfld.long 0x4 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x4 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x4 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x4 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x8 "CHCFG12,Channel Configuration Register"
|
|
bitfld.long 0x8 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x8 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x8 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x8 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x8 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0xC "CHCFG13,Channel Configuration Register"
|
|
bitfld.long 0xC 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0xC 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0xC 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0xC 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0xC 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x10 "CHCFG14,Channel Configuration Register"
|
|
bitfld.long 0x10 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x10 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x10 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x10 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x10 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x14 "CHCFG15,Channel Configuration Register"
|
|
bitfld.long 0x14 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x14 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x14 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x14 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x14 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x18 "CHCFG16,Channel Configuration Register"
|
|
bitfld.long 0x18 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x18 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x18 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x18 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x18 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x1C "CHCFG17,Channel Configuration Register"
|
|
bitfld.long 0x1C 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x1C 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x1C 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x1C 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x1C 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x20 "CHCFG18,Channel Configuration Register"
|
|
bitfld.long 0x20 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x20 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x20 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x20 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x20 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x24 "CHCFG19,Channel Configuration Register"
|
|
bitfld.long 0x24 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x24 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x24 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x24 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x24 0.--4. 1. "INSEL,ADC Input Selection"
|
|
group.long 0x44++0x1F
|
|
line.long 0x0 "CHCFG2,Channel Configuration Register"
|
|
bitfld.long 0x0 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x0 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x0 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x4 "CHCFG3,Channel Configuration Register"
|
|
bitfld.long 0x4 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x4 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x4 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x4 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x8 "CHCFG4,Channel Configuration Register"
|
|
bitfld.long 0x8 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x8 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x8 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x8 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x8 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0xC "CHCFG5,Channel Configuration Register"
|
|
bitfld.long 0xC 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0xC 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0xC 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0xC 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0xC 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x10 "CHCFG6,Channel Configuration Register"
|
|
bitfld.long 0x10 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x10 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x10 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x10 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x10 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x14 "CHCFG7,Channel Configuration Register"
|
|
bitfld.long 0x14 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x14 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x14 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x14 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x14 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x18 "CHCFG8,Channel Configuration Register"
|
|
bitfld.long 0x18 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x18 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x18 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x18 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x18 0.--4. 1. "INSEL,ADC Input Selection"
|
|
line.long 0x1C "CHCFG9,Channel Configuration Register"
|
|
bitfld.long 0x1C 22.--23. "CLASSEL,Conversion Class Selection" "0: select settings from CONVCFG0,1: select settings from CONVCFG1,2: select settings from CONVCFG2,3: select settings from CONVCFG3"
|
|
bitfld.long 0x1C 19.--21. "CMPSEL,Compare Selection" "0: Compare Channel 0,1: Compare Channel 1,2: Compare Channel 2,3: Compare Channel 3,4: none,?,?,?"
|
|
newline
|
|
bitfld.long 0x1C 16.--18. "FILSEL,Filter Selection" "0: Filter Channel 0,1: Filter Channel 1,2: Filter Channel 2,3: Filter Channel 3,4: none,?,?,?"
|
|
hexmask.long.byte 0x1C 8.--11. 1. "CHREP,Channel Repetition"
|
|
newline
|
|
hexmask.long.byte 0x1C 0.--4. 1. "INSEL,ADC Input Selection"
|
|
group.long 0x8C++0x3
|
|
line.long 0x0 "CHSTAT,Channel Status Register"
|
|
hexmask.long.byte 0x0 24.--28. 1. "CHNUM,Current Channel under conversion"
|
|
bitfld.long 0x0 19. "CH19,Channel 19 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 18. "CH18,Channel 18 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 17. "CH17,Channel 17 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 16. "CH16,Channel 16 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 15. "CH15,Channel 15 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 14. "CH14,Channel 14 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 13. "CH13,Channel 13 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 12. "CH12,Channel 12 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 11. "CH11,Channel 11 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 10. "CH10,Channel 10 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 9. "CH9,Channel 9 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 8. "CH8,Channel 8 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 7. "CH7,Channel 7 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 6. "CH6,Channel 6 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 5. "CH5,Channel 5 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 4. "CH4,Channel 4 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 3. "CH3,Channel 3 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 2. "CH2,Channel 2 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 1. "CH1,Channel 1 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 0. "CH0,Channel 0 Status" "0: status not set,1: status set"
|
|
wgroup.long 0x90++0x7
|
|
line.long 0x0 "CHSTATCLR,Channel Status Register"
|
|
bitfld.long 0x0 19. "CH19CLR,Channel 19 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 18. "CH18CLR,Channel 18 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 17. "CH17CLR,Channel 17 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 16. "CH16CLR,Channel 16 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 15. "CH15CLR,Channel 15 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 14. "CH14CLR,Channel 14 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 13. "CH13CLR,Channel 13 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 12. "CH12CLR,Channel 12 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 11. "CH11CLR,Channel 11 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 10. "CH10CLR,Channel 10 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 9. "CH9CLR,Channel 9 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 8. "CH8CLR,Channel 8 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 7. "CH7CLR,Channel 7 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 6. "CH6CLR,Channel 6 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 5. "CH5CLR,Channel 5 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 4. "CH4CLR,Channel 4 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 3. "CH3CLR,Channel 3 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 2. "CH2CLR,Channel 2 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 1. "CH1CLR,Channel 1 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 0. "CH0CLR,Channel 0 Status clear flag" "0: no effect,1: status clear"
|
|
line.long 0x4 "CHSTATSET,Channel Status Set Register"
|
|
bitfld.long 0x4 19. "CH19SET,Channel 19 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 18. "CH18SET,Channel 18 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 17. "CH17SET,Channel 17 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 16. "CH16SET,Channel 16 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 15. "CH15SET,Channel 15 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 14. "CH14SET,Channel 14 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 13. "CH13SET,Channel 13 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 12. "CH12SET,Channel 12 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 11. "CH11SET,Channel 11 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 10. "CH10SET,Channel 10 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 9. "CH9SET,Channel 9 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 8. "CH8SET,Channel 8 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 7. "CH7SET,Channel 7 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 6. "CH6SET,Channel 6 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 5. "CH5SET,Channel 5 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 4. "CH4SET,Channel 4 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 3. "CH3SET,Channel 3 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 2. "CH2SET,Channel 2 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 1. "CH1SET,Channel 1 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 0. "CH0SET,Channel 0 Status set flag" "0: no effect,1: status set"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "CLKCON,Clock Control Register"
|
|
hexmask.long.byte 0x0 0.--3. 1. "CLKDIV,Clock Divider Settings"
|
|
group.long 0x120++0x13
|
|
line.long 0x0 "CMPCFG0,Compare Channel 0 Control Register"
|
|
bitfld.long 0x0 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x0 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x0 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x0 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x0 12.--13. "HYST_LO,Hysteresis set for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x0 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x0 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x4 "CMPCFG1,Compare Channel 1 Control Register"
|
|
bitfld.long 0x4 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x4 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x4 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x4 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x4 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x4 12.--13. "HYST_LO,Hysteresis set for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x4 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x4 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x8 "CMPCFG2,Compare Channel 2 Control Register"
|
|
bitfld.long 0x8 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x8 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x8 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x8 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x8 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x8 12.--13. "HYST_LO,Hysteresis set for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x8 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x8 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0xC "CMPCFG3,Compare Channel 3 Control Register"
|
|
bitfld.long 0xC 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0xC 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0xC 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0xC 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0xC 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0xC 12.--13. "HYST_LO,Hysteresis set for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0xC 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0xC 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x10 "CMPSTAT,Compare Status Register"
|
|
hexmask.long.byte 0x10 24.--27. 1. "CMP_UP,Compare up Status"
|
|
bitfld.long 0x10 23. "CMP_UP3_IS,Compare 3 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 22. "CMP_UP2_IS,Compare 2 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 21. "CMP_UP1_IS,Compare 1 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 20. "CMP_UP0_IS,Compare 0 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 19. "CMP_UP3_STS,Compare 3 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 18. "CMP_UP2_STS,Compare 2 up Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 17. "CMP_UP1_STS,Compare 1 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 16. "CMP_UP0_STS,Compare 0 up Status" "0: status not set,1: status set"
|
|
hexmask.long.byte 0x10 8.--11. 1. "CMP_LO,Compare low Status"
|
|
newline
|
|
bitfld.long 0x10 7. "CMP_LO3_IS,Compare 3 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 6. "CMP_LO2_IS,Compare 2 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 5. "CMP_LO1_IS,Compare 1 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 4. "CMP_LO0_IS,Compare 0 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 3. "CMP_LO3_STS,Compare 3 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 2. "CMP_LO2_STS,Compare 2 low Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x10 1. "CMP_LO1_STS,Compare 1 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x10 0. "CMP_LO0_STS,Compare 0 low Status" "0: status not set,1: status set"
|
|
wgroup.long 0x134++0x7
|
|
line.long 0x0 "CMPSTATCLR,Compare Status Clear Register"
|
|
bitfld.long 0x0 23. "CMP_UP3_ISCLR,Compare 3 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 22. "CMP_UP2_ISCLR,Compare 2 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 21. "CMP_UP1_ISCLR,Compare 1 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 20. "CMP_UP0_ISCLR,Compare 0 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 19. "CMP_UP3_STSCLR,Compare 3 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 18. "CMP_UP2_STSCLR,Compare 2 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 17. "CMP_UP1_STSCLR,Compare 1 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 16. "CMP_UP0_STSCLR,Compare 0 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 7. "CMP_LO3_ISCLR,Compare 3 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 6. "CMP_LO2_ISCLR,Compare 2 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP_LO1_ISCLR,Compare 1 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 4. "CMP_LO0_ISCLR,Compare 0 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 3. "CMP_LO3_STSCLR,Compare 3 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 2. "CMP_LO2_STSCLR,Compare 2 low Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP_LO1_STSCLR,Compare 1 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 0. "CMP_LO0_STSCLR,Compare 0 low Status clear" "0: no effect,1: status clear"
|
|
line.long 0x4 "CMPSTATSET,Compare Status Set Register"
|
|
bitfld.long 0x4 23. "CMP_UP3_ISSET,Compare 3 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 22. "CMP_UP2_ISSET,Compare 2 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 21. "CMP_UP1_ISSET,Compare 1 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 20. "CMP_UP0_ISSET,Compare 0 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 19. "CMP_UP3_STSSET,Compare 3 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 18. "CMP_UP2_STSSET,Compare 2 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 17. "CMP_UP1_STSSET,Compare 1 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 16. "CMP_UP0_STSSET,Compare 0 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 7. "CMP_LO3_ISSET,Compare 3 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 6. "CMP_LO2_ISSET,Compare 2 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 5. "CMP_LO1_ISSET,Compare 1 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 4. "CMP_LO0_ISSET,Compare 0 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 3. "CMP_LO3_STSSET,Compare 3 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 2. "CMP_LO2_STSSET,Compare 2 low Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 1. "CMP_LO1_STSSET,Compare 1 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 0. "CMP_LO0_STSSET,Compare 0 low Status set" "0: no effect,1: status set"
|
|
group.long 0x98++0xF
|
|
line.long 0x0 "CONVCFG0,Conversion Configuration Register"
|
|
bitfld.long 0x0 14. "BWD_HI_CUR,BWD current configuration" "0: selected,1: selected (High current Mode)"
|
|
bitfld.long 0x0 12.--13. "BWD,BWD timing config" "0: tBWD = 0 (BWD is disabled),1: tBWD = 4*ADC_CLK,2: tBWD = 8*ADC_CLK,3: tBWD = 16*ADC_CLK"
|
|
newline
|
|
bitfld.long 0x0 11. "PCAL,Post Calibration enable" "0,1"
|
|
bitfld.long 0x0 10. "MSBD,MSB doubling enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "SESP,Spread early sample point config" "0,1"
|
|
hexmask.long.byte 0x0 4.--7. 1. "STC,Sample Time config"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "OVERS,Oversampling config" "0,1,2,3"
|
|
bitfld.long 0x0 0.--1. "TCONF,Tracking Conversion config" "0,1,2,3"
|
|
line.long 0x4 "CONVCFG1,Conversion Configuration Register"
|
|
bitfld.long 0x4 14. "BWD_HI_CUR,BWD current configuration" "0: selected,1: selected (High current Mode)"
|
|
bitfld.long 0x4 12.--13. "BWD,BWD timing config" "0: tBWD = 0 (BWD is disabled),1: tBWD = 4*ADC_CLK,2: tBWD = 8*ADC_CLK,3: tBWD = 16*ADC_CLK"
|
|
newline
|
|
bitfld.long 0x4 11. "PCAL,Post Calibration enable" "0,1"
|
|
bitfld.long 0x4 10. "MSBD,MSB doubling enable" "0,1"
|
|
newline
|
|
bitfld.long 0x4 8. "SESP,Spread early sample point config" "0,1"
|
|
hexmask.long.byte 0x4 4.--7. 1. "STC,Sample Time config"
|
|
newline
|
|
bitfld.long 0x4 2.--3. "OVERS,Oversampling config" "0,1,2,3"
|
|
bitfld.long 0x4 0.--1. "TCONF,Tracking Conversion config" "0,1,2,3"
|
|
line.long 0x8 "CONVCFG2,Conversion Configuration Register"
|
|
bitfld.long 0x8 14. "BWD_HI_CUR,BWD current configuration" "0: selected,1: selected (High current Mode)"
|
|
bitfld.long 0x8 12.--13. "BWD,BWD timing config" "0: tBWD = 0 (BWD is disabled),1: tBWD = 4*ADC_CLK,2: tBWD = 8*ADC_CLK,3: tBWD = 16*ADC_CLK"
|
|
newline
|
|
bitfld.long 0x8 11. "PCAL,Post Calibration enable" "0,1"
|
|
bitfld.long 0x8 10. "MSBD,MSB doubling enable" "0,1"
|
|
newline
|
|
bitfld.long 0x8 8. "SESP,Spread early sample point config" "0,1"
|
|
hexmask.long.byte 0x8 4.--7. 1. "STC,Sample Time config"
|
|
newline
|
|
bitfld.long 0x8 2.--3. "OVERS,Oversampling config" "0,1,2,3"
|
|
bitfld.long 0x8 0.--1. "TCONF,Tracking Conversion config" "0,1,2,3"
|
|
line.long 0xC "CONVCFG3,Conversion Configuration Register"
|
|
bitfld.long 0xC 14. "BWD_HI_CUR,BWD current configuration" "0: selected,1: selected (High current Mode)"
|
|
bitfld.long 0xC 12.--13. "BWD,BWD timing config" "0: tBWD = 0 (BWD is disabled),1: tBWD = 4*ADC_CLK,2: tBWD = 8*ADC_CLK,3: tBWD = 16*ADC_CLK"
|
|
newline
|
|
bitfld.long 0xC 11. "PCAL,Post Calibration enable" "0,1"
|
|
bitfld.long 0xC 10. "MSBD,MSB doubling enable" "0,1"
|
|
newline
|
|
bitfld.long 0xC 8. "SESP,Spread early sample point config" "0,1"
|
|
hexmask.long.byte 0xC 4.--7. 1. "STC,Sample Time config"
|
|
newline
|
|
bitfld.long 0xC 2.--3. "OVERS,Oversampling config" "0,1,2,3"
|
|
bitfld.long 0xC 0.--1. "TCONF,Tracking Conversion config" "0,1,2,3"
|
|
rgroup.long 0xB4++0xF
|
|
line.long 0x0 "FIL0,Filter Result Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x4 "FIL1,Filter Result Register"
|
|
hexmask.long.word 0x4 0.--15. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x8 "FIL2,Filter Result Register"
|
|
hexmask.long.word 0x8 0.--15. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0xC "FIL3,Filter Result Register"
|
|
hexmask.long.word 0xC 0.--15. 1. "FILRESULT,Filter Result Value"
|
|
group.long 0xC4++0x3
|
|
line.long 0x0 "FILSTAT,Filter Status Register"
|
|
bitfld.long 0x0 3. "FIL3,Filter 3 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 2. "FIL2,Filter 2 Event flag" "0: event not set,1: event set"
|
|
newline
|
|
bitfld.long 0x0 1. "FIL1,Filter 1 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 0. "FIL0,Filter 0 Event flag" "0: event not set,1: event set"
|
|
wgroup.long 0xC8++0x7
|
|
line.long 0x0 "FILSTATCLR,Filter Status Clear Register"
|
|
bitfld.long 0x0 3. "FIL3CLR,Filter 3 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 2. "FIL2CLR,Filter 2 Event flag clear" "0: no effect,1: event clear"
|
|
newline
|
|
bitfld.long 0x0 1. "FIL1CLR,Filter 1 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 0. "FIL0CLR,Filter 0 Event flag clear" "0: no effect,1: event clear"
|
|
line.long 0x4 "FILSTATSET,Filter Status Set Register"
|
|
bitfld.long 0x4 3. "FIL3SET,Filter 3 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 2. "FIL2SET,Filter 2 Event flag set" "0: no effect,1: event set"
|
|
newline
|
|
bitfld.long 0x4 1. "FIL1SET,Filter 1 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 0. "FIL0SET,Filter 0 Event flag set" "0: no effect,1: event set"
|
|
group.long 0xB0++0x3
|
|
line.long 0x0 "FILTCFG,Filter Configuration"
|
|
bitfld.long 0x0 12.--13. "COEF_A3,Filter Coefficient" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 8.--9. "COEF_A2,Filter Coefficient" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "COEF_A1,Filter Coefficient" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 0.--1. "COEF_A0,Filter Coefficient" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "GLOBCONF,Global Configuration Register"
|
|
bitfld.long 0x0 5. "ISTE,Idle shadow transfer enable" "0: Shadow transfer done based on selected shadow..,1: Shadow transfer is automatically enabled when no.."
|
|
bitfld.long 0x0 0. "EN,Module Enable" "0: ADC1 Module is disabled,1: ADC1 Module is enabled"
|
|
group.long 0x13C++0x17
|
|
line.long 0x0 "IEN0,Interrupt Enable Register 0"
|
|
bitfld.long 0x0 31. "IEN_UP3,Compare 3 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 30. "IEN_UP2,Compare 2 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 29. "IEN_UP1,Compare 1 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 28. "IEN_UP0,Compare 0 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 27. "IEN_LO3,Compare 3 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 26. "IEN_LO2,Compare 2 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 25. "IEN_LO1,Compare 1 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 24. "IEN_LO0,Compare 0 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 23. "IEN_SQ3,Sequence 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 22. "IEN_SQ2,Sequence 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 21. "IEN_SQ1,Sequence 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 20. "IEN_SQ0,Sequence 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 19. "IEN_CH19,Channel 19 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 18. "IEN_CH18,Channel 18 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 17. "IEN_CH17,Channel 17 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 16. "IEN_CH16,Channel 16 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 15. "IEN_CH15,Channel 15 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 14. "IEN_CH14,Channel 14 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 13. "IEN_CH13,Channel 13 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 12. "IEN_CH12,Channel 12 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 11. "IEN_CH11,Channel 11 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 10. "IEN_CH10,Channel 10 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 9. "IEN_CH9,Channel 9 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 8. "IEN_CH8,Channel 8 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 7. "IEN_CH7,Channel 7 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 6. "IEN_CH6,Channel 6 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 5. "IEN_CH5,Channel 5 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 4. "IEN_CH4,Channel 4 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 3. "IEN_CH3,Channel 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 2. "IEN_CH2,Channel 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 1. "IEN_CH1,Channel 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 0. "IEN_CH0,Channel 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
line.long 0x4 "IEN1,Interrupt Enable Register 1"
|
|
bitfld.long 0x4 7. "IEN_WFR3,WFR 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 6. "IEN_WFR2,WFR 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 5. "IEN_WFR1,WFR 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 4. "IEN_WFR0,WFR 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 3. "IEN_COLL3,Collision 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 2. "IEN_COLL2,Collision 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 1. "IEN_COLL1,Collision 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 0. "IEN_COLL0,Collision 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
line.long 0x8 "INP0,Interrupt Node Pointer Register 0"
|
|
bitfld.long 0x8 30.--31. "INP_CH15,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 28.--29. "INP_CH14,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 26.--27. "INP_CH13,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 24.--25. "INP_CH12,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 22.--23. "INP_CH11,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 20.--21. "INP_CH10,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 18.--19. "INP_CH9,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 16.--17. "INP_CH8,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 14.--15. "INP_CH7,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 12.--13. "INP_CH6,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 10.--11. "INP_CH5,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 8.--9. "INP_CH4,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 6.--7. "INP_CH3,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 4.--5. "INP_CH2,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 2.--3. "INP_CH1,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 0.--1. "INP_CH0,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
line.long 0xC "INP1,Interrupt Node Pointer Register 1"
|
|
bitfld.long 0xC 6.--7. "INP_CH19,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 4.--5. "INP_CH18,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 2.--3. "INP_CH17,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 0.--1. "INP_CH16,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
line.long 0x10 "INP2,Interrupt Node Pointer Register 2"
|
|
bitfld.long 0x10 14.--15. "INP_CMP_UP3,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 12.--13. "INP_CMP_UP2,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 10.--11. "INP_CMP_UP1,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 8.--9. "INP_CMP_UP0,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 6.--7. "INP_CMP_LO3,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 4.--5. "INP_CMP_LO2,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 2.--3. "INP_CMP_LO1,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 0.--1. "INP_CMP_LO0,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
line.long 0x14 "INP3,Interrupt Node Pointer Register 3"
|
|
bitfld.long 0x14 22.--23. "INP_WFR3,Wait for read Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 20.--21. "INP_WFR2,Wait for read Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x14 18.--19. "INP_WFR1,Wait for read Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 16.--17. "INP_WFR0,Wait for read Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x14 14.--15. "INP_COLL3,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 12.--13. "INP_COLL2,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x14 10.--11. "INP_COLL1,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 8.--9. "INP_COLL0,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x14 6.--7. "INP_SQ3,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 4.--5. "INP_SQ2,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x14 2.--3. "INP_SQ1,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x14 0.--1. "INP_SQ0,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
rgroup.long 0xD0++0x7
|
|
line.long 0x0 "RES0,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES1,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--13. 1. "RESULT,Result Value"
|
|
rgroup.long 0xF8++0x27
|
|
line.long 0x0 "RES10,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES11,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x8 "RES12,Result Register"
|
|
bitfld.long 0x8 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x8 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0xC "RES13,Result Register"
|
|
bitfld.long 0xC 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0xC 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x10 "RES14,Result Register"
|
|
bitfld.long 0x10 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x10 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x14 "RES15,Result Register"
|
|
bitfld.long 0x14 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x14 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x18 "RES16,Result Register"
|
|
bitfld.long 0x18 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x18 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x1C "RES17,Result Register"
|
|
bitfld.long 0x1C 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x1C 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x20 "RES18,Result Register"
|
|
bitfld.long 0x20 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x20 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x24 "RES19,Result Register"
|
|
bitfld.long 0x24 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x24 0.--13. 1. "RESULT,Result Value"
|
|
rgroup.long 0xD8++0x1F
|
|
line.long 0x0 "RES2,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES3,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x8 "RES4,Result Register"
|
|
bitfld.long 0x8 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x8 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0xC "RES5,Result Register"
|
|
bitfld.long 0xC 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0xC 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x10 "RES6,Result Register"
|
|
bitfld.long 0x10 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x10 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x14 "RES7,Result Register"
|
|
bitfld.long 0x14 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x14 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x18 "RES8,Result Register"
|
|
bitfld.long 0x18 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x18 0.--13. 1. "RESULT,Result Value"
|
|
line.long 0x1C "RES9,Result Register"
|
|
bitfld.long 0x1C 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x1C 0.--13. 1. "RESULT,Result Value"
|
|
group.long 0x164++0x3
|
|
line.long 0x0 "SHDCTR,Shadow Transfer Control Register"
|
|
bitfld.long 0x0 22. "STE_GTG,Gating Shadow Transfer Enable" "0: Shadow transfer disabled,1: Shadow transfer enabled"
|
|
bitfld.long 0x0 21. "STE_TRG,Trigger Shadow Transfer Enable" "0: Shadow transfer disabled,1: Shadow transfer enabled"
|
|
newline
|
|
bitfld.long 0x0 20. "STE_SQ,Sequence Shadow Transfer Enable" "0: Shadow transfer disabled,1: Shadow transfer enabled"
|
|
bitfld.long 0x0 18. "ST_GTGSW,Gating Software Shadow Transfer" "0: Shadow transfer not triggered,1: Shadow transfer is triggered"
|
|
newline
|
|
bitfld.long 0x0 17. "ST_TRGSW,Trigger Software Shadow Transfer" "0: Shadow transfer not triggered,1: Shadow transfer is triggered"
|
|
bitfld.long 0x0 16. "ST_SQSW,Sequence Software Shadow Transfer" "0: Shadow transfer not triggered,1: Shadow transfer is triggered"
|
|
newline
|
|
bitfld.long 0x0 14. "STE_GTGSEL,Gating Shadow Transfer Enable Selection" "0: Software Shadow transfer enable,1: Shadow transfer with external CCU7 Shadow transfer"
|
|
bitfld.long 0x0 13. "STE_TRGSEL,Trigger Shadow Transfer Enable Selection" "0: Software Shadow transfer enable,1: Shadow transfer with external CCU7 Shadow transfer"
|
|
newline
|
|
bitfld.long 0x0 12. "STE_SQSEL,Sequence Shadow Transfer Enable Selection" "0: Software Shadow transfer enable,1: Shadow transfer with external CCU7 Shadow transfer"
|
|
bitfld.long 0x0 8.--10. "ST_GTGSEL,Gating Shadow Transfer Selection" "0: Software Trigger,1: T12 Zero Match,2: T12 Period Match,3: T13 Period Match,4: T14 Period Match,5: T15 Period Match,6: T16 Period Match,7: not used"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "ST_TRGSEL,Trigger Shadow Transfer Selection" "0: Software Trigger,1: T12 Zero Match,2: T12 Period Match,3: T13 Period Match,4: T14 Period Match,5: T15 Period Match,6: T16 Period Match,7: not used"
|
|
bitfld.long 0x0 0.--2. "ST_SQSEL,Sequence Shadow Transfer Selection" "0: Software Trigger,1: T12 Zero Match,2: T12 Period Match,3: T13 Period Match,4: T14 Period Match,5: T15 Period Match,6: T16 Period Match,7: not used"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "SQCFG0,Sequence Configuration Register"
|
|
bitfld.long 0x0 15. "GTSW,Trigger Software Gating" "0: The selected trigger source is gated off,1: The selected trigger source is not gated"
|
|
bitfld.long 0x0 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "GTSEL,Gating Select" "0: Software Gating,1: CC70A State,2: C71B State,3: T13 Compare Status"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TRGSEL,Trigger Select"
|
|
newline
|
|
bitfld.long 0x0 7. "WFRCFG,Wait for Read Enable" "0: Wait for Read disabled,1: Wait for Read enabled"
|
|
bitfld.long 0x0 6. "COLLCFG,Collision Config" "0: The trigger request for a sequence is discarded..,1: The trigger request for a sequence is set to.."
|
|
newline
|
|
bitfld.long 0x0 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x0 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "SQCFG1,Sequence Configuration Register"
|
|
bitfld.long 0x0 15. "GTSW,Trigger Software Gating" "0: The selected trigger source is gated off,1: The selected trigger source is not gated"
|
|
bitfld.long 0x0 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "GTSEL,Gating Select" "0: Software Gating,1: CC71A State,2: C70B State,3: T14 Compare Status"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TRGSEL,Trigger Select"
|
|
newline
|
|
bitfld.long 0x0 7. "WFRCFG,Wait for Read Enable" "0: Wait for Read disabled,1: Wait for Read enabled"
|
|
bitfld.long 0x0 6. "COLLCFG,Collision Config" "0: The trigger request for a sequence is discarded..,1: The trigger request for a sequence is set to.."
|
|
newline
|
|
bitfld.long 0x0 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x0 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "SQCFG2,Sequence Configuration Register"
|
|
bitfld.long 0x0 15. "GTSW,Trigger Software Gating" "0: The selected trigger source is gated off,1: The selected trigger source is not gated"
|
|
bitfld.long 0x0 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "GTSEL,Gating Select" "0: Software Gating,1: CC72B State,2: C72B State,3: T15 Compare Status"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TRGSEL,Trigger Select"
|
|
newline
|
|
bitfld.long 0x0 7. "WFRCFG,Wait for Read Enable" "0: Wait for Read disabled,1: Wait for Read enabled"
|
|
bitfld.long 0x0 6. "COLLCFG,Collision Config" "0: The trigger request for a sequence is discarded..,1: The trigger request for a sequence is set to.."
|
|
newline
|
|
bitfld.long 0x0 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x0 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "SQCFG3,Sequence Configuration Register"
|
|
bitfld.long 0x0 15. "GTSW,Trigger Software Gating" "0: The selected trigger source is gated off,1: The selected trigger source is not gated"
|
|
bitfld.long 0x0 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "GTSEL,Gating Select" "0: Software Gating,1: T13 Compare Status,?,3: T16 Compare Status"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TRGSEL,Trigger Select"
|
|
newline
|
|
bitfld.long 0x0 7. "WFRCFG,Wait for Read Enable" "0: Wait for Read disabled,1: Wait for Read enabled"
|
|
bitfld.long 0x0 6. "COLLCFG,Collision Config" "0: The trigger request for a sequence is discarded..,1: The trigger request for a sequence is set to.."
|
|
newline
|
|
bitfld.long 0x0 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x0 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "SQSLOT0,SQ Channel Slot Register"
|
|
hexmask.long.byte 0x0 24.--28. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x0 16.--20. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--12. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CHSEL0,Channel Select"
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "SQSLOT1,SQ Channel Slot Register"
|
|
hexmask.long.byte 0x0 24.--28. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x0 16.--20. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--12. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CHSEL0,Channel Select"
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "SQSLOT2,SQ Channel Slot Register"
|
|
hexmask.long.byte 0x0 24.--28. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x0 16.--20. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--12. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CHSEL0,Channel Select"
|
|
group.long 0x2C++0xF
|
|
line.long 0x0 "SQSLOT3,SQ Channel Slot Register"
|
|
hexmask.long.byte 0x0 24.--28. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x0 16.--20. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--12. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CHSEL0,Channel Select"
|
|
line.long 0x4 "SQSTAT,Sequence Status Register"
|
|
bitfld.long 0x4 16.--18. "SQNUM,Actual Sequence processed" "0: SQ 0 is running,1: SQ1 is running,2: SQ2 is running,3: SQ3 is running,?,?,?,7: No SQ is running"
|
|
bitfld.long 0x4 11. "COLL3,Collision 3 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 10. "COLL2,Collision 2 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x4 9. "COLL1,Collision 1 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 8. "COLL0,Collision 0 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x4 7. "WFR3,Wait for Read 3 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 6. "WFR2,Wait for Read 2 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x4 5. "WFR1,Wait for Read 1 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 4. "WFR0,Wait for Read 0 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x4 3. "SQ3,SQ 3 Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 2. "SQ2,SQ 2 Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x4 1. "SQ1,SQ 1 Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x4 0. "SQ0,SQ 0 Interrupt Status" "0: status not set,1: status set"
|
|
line.long 0x8 "SQSTATCLR,Sequence Status Clear Register"
|
|
bitfld.long 0x8 11. "COLL3CLR,Collision 3 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 10. "COLL2CLR,Collision 2 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x8 9. "COLL1CLR,Collision 1 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 8. "COLL0CLR,Collision 0 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x8 7. "WFR3CLR,Wait for Read 3 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 6. "WFR2CLR,Wait for Read 2 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x8 5. "WFR1CLR,Wait for Read 1 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 4. "WFR0CLR,Wait for Read 0 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x8 3. "SQ3CLR,SQ 3 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 2. "SQ2CLR,SQ 2 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x8 1. "SQ1CLR,SQ 1 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x8 0. "SQ0CLR,SQ 0 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
line.long 0xC "SQSTATSET,Sequence Status Clear Register"
|
|
bitfld.long 0xC 11. "COLL3SET,Collision 3 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 10. "COLL2SET,Collision 2 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0xC 9. "COLL1SET,Collision 1 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 8. "COLL0SET,Collision 0 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0xC 7. "WFR3SET,Wait for Read 3 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 6. "WFR2SET,Wait for Read 2 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0xC 5. "WFR1SET,Wait for Read 1 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 4. "WFR0SET,Wait for Read 0 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0xC 3. "SQ3SET,SQ 3 Interrupt Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 2. "SQ2SET,SQ 2 Interrupt Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0xC 1. "SQ1SET,SQ 1 Interrupt Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0xC 0. "SQ0SET,SQ 0 Interrupt Status Set" "0: no effect,1: status set"
|
|
group.long 0x8++0x3
|
|
line.long 0x0 "SUSCTR,Suspend Control Register"
|
|
bitfld.long 0x0 1. "SUSMOD,Suspend Mode" "0: Hard Suspend Mode,1: Soft Suspend Mode"
|
|
bitfld.long 0x0 0. "SUSEN,ADC1 Suspend Enable" "0: ADC1 Suspend Mode is disabled,1: ADC1 Suspend Mode is enabled"
|
|
rgroup.long 0xC++0x3
|
|
line.long 0x0 "SUSSTAT,Suspend Status Register"
|
|
bitfld.long 0x0 1. "READY,Module Ready" "0: ADC is not ready,1: ADC is ready for operation"
|
|
bitfld.long 0x0 0. "STAT,Suspend Mode Status" "0: Suspend Mode is not entered,1: Suspend mode is entered"
|
|
tree.end
|
|
tree "ADC2 (Monitoring Analog Digital Converter)"
|
|
base ad:0x4804C000
|
|
group.long 0x128++0x7
|
|
line.long 0x0 "CALAI0,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x4 "CALAI1,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x4 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x4 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0x150++0x13
|
|
line.long 0x0 "CALAI10,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x4 "CALAI11,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x4 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x4 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x8 "CALAI12,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x8 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x8 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0xC "CALAI13,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0xC 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0xC 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x10 "CALAI14,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x10 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x10 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0x130++0x1F
|
|
line.long 0x0 "CALAI2,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x0 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x4 "CALAI3,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x4 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x4 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x8 "CALAI4,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x8 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x8 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0xC "CALAI5,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0xC 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0xC 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x10 "CALAI6,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x10 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x10 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x14 "CALAI7,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x14 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x14 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x18 "CALAI8,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x18 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x18 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
line.long 0x1C "CALAI9,Calibration Setting for Analog Inputs"
|
|
hexmask.long.byte 0x1C 16.--23. 1. "CALGAIN,Calibration Gain"
|
|
hexmask.long.byte 0x1C 0.--4. 1. "CALOFFS,Calibration Offset"
|
|
group.long 0x28++0x7
|
|
line.long 0x0 "CALEN,Calibration Enable"
|
|
bitfld.long 0x0 14. "CALEN14,Channel 14 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 13. "CALEN13,Channel 13 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 12. "CALEN12,Channel 12 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 11. "CALEN11,Channel 11 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 10. "CALEN10,Channel 10 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 9. "CALEN9,Channel 9 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 8. "CALEN8,Channel 8 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 7. "CALEN7,Channel 7 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 6. "CALEN6,Channel 6 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 5. "CALEN5,Channel 5 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "CALEN4,Channel 4 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 3. "CALEN3,Channel 3 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "CALEN2,Channel 2 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
bitfld.long 0x0 1. "CALEN1,Channel 1 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "CALEN0,Channel 0 Calibration Enable" "0: calibration disabled,1: calibration enabled"
|
|
line.long 0x4 "CALPEN,Calibration Protection Enable"
|
|
bitfld.long 0x4 14. "CALPEN14,Channel 14 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 13. "CALPEN13,Channel 13 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 12. "CALPEN12,Channel 12 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 11. "CALPEN11,Channel 11 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 10. "CALPEN10,Channel 10 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 9. "CALPEN9,Channel 9 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 8. "CALPEN8,Channel 8 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 7. "CALPEN7,Channel 7 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 6. "CALPEN6,Channel 6 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 5. "CALPEN5,Channel 5 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 4. "CALPEN4,Channel 4 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 3. "CALPEN3,Channel 3 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 2. "CALPEN2,Channel 2 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
bitfld.long 0x4 1. "CALPEN1,Channel 1 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "CALPEN0,Channel 0 Calibration Protection" "0: protection disabled,1: protection enabled"
|
|
group.long 0xE8++0x7
|
|
line.long 0x0 "CHCFG0,Channel Configuration Register 0"
|
|
bitfld.long 0x0 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x0 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x4 "CHCFG1,Channel Configuration Register 1"
|
|
bitfld.long 0x4 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x4 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x4 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
group.long 0x110++0x13
|
|
line.long 0x0 "CHCFG10,Channel Configuration Register 10"
|
|
bitfld.long 0x0 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x0 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x4 "CHCFG11,Channel Configuration Register 11"
|
|
bitfld.long 0x4 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x4 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x4 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x8 "CHCFG12,Channel Configuration Register 12"
|
|
bitfld.long 0x8 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x8 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x8 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x8 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0xC "CHCFG13,Channel Configuration Register 13"
|
|
bitfld.long 0xC 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0xC 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0xC 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0xC 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x10 "CHCFG14,Channel Configuration Register 14"
|
|
bitfld.long 0x10 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x10 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x10 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x10 8.--11. 1. "CHREP,Channel Repetition"
|
|
group.long 0xF0++0x1F
|
|
line.long 0x0 "CHCFG2,Channel Configuration Register 2"
|
|
bitfld.long 0x0 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x0 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x4 "CHCFG3,Channel Configuration Register 3"
|
|
bitfld.long 0x4 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x4 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x4 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x8 "CHCFG4,Channel Configuration Register 4"
|
|
bitfld.long 0x8 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x8 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x8 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x8 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0xC "CHCFG5,Channel Configuration Register 5"
|
|
bitfld.long 0xC 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0xC 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0xC 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0xC 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x10 "CHCFG6,Channel Configuration Register 6"
|
|
bitfld.long 0x10 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x10 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x10 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x10 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x14 "CHCFG7,Channel Configuration Register 7"
|
|
bitfld.long 0x14 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x14 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x14 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x14 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x18 "CHCFG8,Channel Configuration Register 8"
|
|
bitfld.long 0x18 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x18 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x18 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x18 8.--11. 1. "CHREP,Channel Repetition"
|
|
line.long 0x1C "CHCFG9,Channel Configuration Register 9"
|
|
bitfld.long 0x1C 24.--25. "CLASSEL,Conversion Class Selection" "0: Conversion Class 0,1: Conversion Class 1,2: Conversion Class 2,3: Conversion Class 3"
|
|
hexmask.long.byte 0x1C 20.--23. 1. "CMPSEL,Compare Selection"
|
|
newline
|
|
hexmask.long.byte 0x1C 16.--19. 1. "FILSEL,Filter Selection"
|
|
hexmask.long.byte 0x1C 8.--11. 1. "CHREP,Channel Repetition"
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "CHSTAT,Channel Status Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "CHNUM,Current Channel under conversion"
|
|
bitfld.long 0x0 14. "CH14,Channel 14 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 13. "CH13,Channel 13 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 12. "CH12,Channel 12 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 11. "CH11,Channel 11 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 10. "CH10,Channel 10 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 9. "CH9,Channel 9 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 8. "CH8,Channel 8 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 7. "CH7,Channel 7 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 6. "CH6,Channel 6 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 5. "CH5,Channel 5 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 4. "CH4,Channel 4 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 3. "CH3,Channel 3 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 2. "CH2,Channel 2 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 1. "CH1,Channel 1 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 0. "CH0,Channel 0 Status" "0: status not set,1: status set"
|
|
wgroup.long 0x20++0x7
|
|
line.long 0x0 "CHSTATCLR,Channel Status Register"
|
|
bitfld.long 0x0 14. "CH14CLR,Channel 14 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 13. "CH13CLR,Channel 13 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 12. "CH12CLR,Channel 12 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 11. "CH11CLR,Channel 11 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 10. "CH10CLR,Channel 10 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 9. "CH9CLR,Channel 9 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 8. "CH8CLR,Channel 8 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 7. "CH7CLR,Channel 7 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 6. "CH6CLR,Channel 6 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 5. "CH5CLR,Channel 5 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 4. "CH4CLR,Channel 4 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 3. "CH3CLR,Channel 3 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 2. "CH2CLR,Channel 2 Status clear flag" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 1. "CH1CLR,Channel 1 Status clear flag" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 0. "CH0CLR,Channel 0 Status clear flag" "0: no effect,1: status clear"
|
|
line.long 0x4 "CHSTATSET,Channel Status Register"
|
|
bitfld.long 0x4 14. "CH14SET,Channel 14 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 13. "CH13SET,Channel 13 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 12. "CH12SET,Channel 12 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 11. "CH11SET,Channel 11 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 10. "CH10SET,Channel 10 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 9. "CH9SET,Channel 9 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 8. "CH8SET,Channel 8 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 7. "CH7SET,Channel 7 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 6. "CH6SET,Channel 6 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 5. "CH5SET,Channel 5 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 4. "CH4SET,Channel 4 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 3. "CH3SET,Channel 3 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 2. "CH2SET,Channel 2 Status set flag" "0: no effect,1: status set"
|
|
bitfld.long 0x4 1. "CH1SET,Channel 1 Status set flag" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 0. "CH0SET,Channel 0 Status set flag" "0: no effect,1: status set"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "CLKCON,Clock Control Register"
|
|
hexmask.long.byte 0x0 0.--3. 1. "CLKDIV,Clock Divider Settings"
|
|
group.long 0x188++0x1F
|
|
line.long 0x0 "CMPCFG0,Compare Channel 0 Control Register"
|
|
bitfld.long 0x0 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x0 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x0 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x0 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x0 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x0 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x0 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x4 "CMPCFG1,Compare Channel 1 Control Register"
|
|
bitfld.long 0x4 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x4 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x4 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x4 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x4 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x4 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x4 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x4 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x8 "CMPCFG2,Compare Channel 2 Control Register"
|
|
bitfld.long 0x8 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x8 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x8 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x8 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x8 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x8 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x8 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x8 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0xC "CMPCFG3,Compare Channel 3 Control Register"
|
|
bitfld.long 0xC 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0xC 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0xC 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0xC 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0xC 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0xC 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0xC 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0xC 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x10 "CMPCFG4,Compare Channel 4 Control Register"
|
|
bitfld.long 0x10 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x10 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x10 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x10 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x10 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x10 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x10 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x10 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x14 "CMPCFG5,Compare Channel 5 Control Register"
|
|
bitfld.long 0x14 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x14 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x14 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x14 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x14 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x14 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x14 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x14 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x18 "CMPCFG6,Compare Channel 6 Control Register"
|
|
bitfld.long 0x18 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x18 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x18 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x18 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x18 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x18 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x18 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x18 0.--7. 1. "LOWER,Lower Compare Value"
|
|
line.long 0x1C "CMPCFG7,Compare Channel 7 Control Register"
|
|
bitfld.long 0x1C 30.--31. "MODE,Compare Mode" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x1C 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x1C 27. "RST_BLANK_TIME,Restart Blank time" "0: No Restart of blank time,1: Restart blank time"
|
|
bitfld.long 0x1C 24.--26. "BLANK_TIME,Blank Time configuration" "0: OFF,1: 5 conversions blank time,2: 10 conversions blank time,3: 20 conversions blank time,4: 30 conversions blank time,5: 40 conversions blank time,6: 50 conversions blank time,7: 60 conversions blank time"
|
|
newline
|
|
hexmask.long.byte 0x1C 16.--23. 1. "UPPER,Upper Compare Value"
|
|
bitfld.long 0x1C 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
bitfld.long 0x1C 8. "INP_SEL,Input selection for the comparator unit" "0: Selects the ahb result,1: Selects the filter result"
|
|
hexmask.long.byte 0x1C 0.--7. 1. "LOWER,Lower Compare Value"
|
|
group.long 0x98++0x3
|
|
line.long 0x0 "CMPSTAT,Compare Status Register"
|
|
bitfld.long 0x0 31. "CMP_UP7_IS,Compare 7 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 30. "CMP_UP6_IS,Compare 6 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 29. "CMP_UP5_IS,Compare 5 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 28. "CMP_UP4_IS,Compare 4 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 27. "CMP_UP3_IS,Compare 3 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 26. "CMP_UP2_IS,Compare 2 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 25. "CMP_UP1_IS,Compare 1 up Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 24. "CMP_UP0_IS,Compare 0 up Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 23. "CMP_UP7_STS,Compare 7 up Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 22. "CMP_UP6_STS,Compare 6 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 21. "CMP_UP5_STS,Compare 5 up Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 20. "CMP_UP4_STS,Compare 4 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 19. "CMP_UP3_STS,Compare 3 up Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 18. "CMP_UP2_STS,Compare 2 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 17. "CMP_UP1_STS,Compare 1 up Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 16. "CMP_UP0_STS,Compare 0 up Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 15. "CMP_LO7_IS,Compare 7 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 14. "CMP_LO6_IS,Compare 6 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 13. "CMP_LO5_IS,Compare 5 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 12. "CMP_LO4_IS,Compare 4 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 11. "CMP_LO3_IS,Compare 3 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 10. "CMP_LO2_IS,Compare 2 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 9. "CMP_LO1_IS,Compare 1 low Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 8. "CMP_LO0_IS,Compare 0 low Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 7. "CMP_LO7_STS,Compare 7 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 6. "CMP_LO6_STS,Compare 6 low Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP_LO5_STS,Compare 5 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 4. "CMP_LO4_STS,Compare 4 low Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 3. "CMP_LO3_STS,Compare 3 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 2. "CMP_LO2_STS,Compare 2 low Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP_LO1_STS,Compare 1 low Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 0. "CMP_LO0_STS,Compare 0 low Status" "0: status not set,1: status set"
|
|
rgroup.long 0x124++0x3
|
|
line.long 0x0 "CMPSTAT2,Compare Status Register"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CMP_UP,Compare up Status"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CMP_LO,Compare low Status"
|
|
wgroup.long 0x9C++0x7
|
|
line.long 0x0 "CMPSTATCLR,Compare Status Clear Register"
|
|
bitfld.long 0x0 31. "CMP_UP7_ISCLR,Compare 7 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 30. "CMP_UP6_ISCLR,Compare 6 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 29. "CMP_UP5_ISCLR,Compare 5 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 28. "CMP_UP4_ISCLR,Compare 4 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 27. "CMP_UP3_ISCLR,Compare 3 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 26. "CMP_UP2_ISCLR,Compare 2 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 25. "CMP_UP1_ISCLR,Compare 1 up Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 24. "CMP_UP0_ISCLR,Compare 0 up Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 23. "CMP_UP7_STSCLR,Compare 7 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 22. "CMP_UP6_STSCLR,Compare 6 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 21. "CMP_UP5_STSCLR,Compare 5 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 20. "CMP_UP4_STSCLR,Compare 4 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 19. "CMP_UP3_STSCLR,Compare 3 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 18. "CMP_UP2_STSCLR,Compare 2 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 17. "CMP_UP1_STSCLR,Compare 1 up Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 16. "CMP_UP0_STSCLR,Compare 0 up Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 15. "CMP_LO7_ISCLR,Compare 7 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 14. "CMP_LO6_ISCLR,Compare 6 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 13. "CMP_LO5_ISCLR,Compare 5 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 12. "CMP_LO4_ISCLR,Compare 4 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 11. "CMP_LO3_ISCLR,Compare 3 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 10. "CMP_LO2_ISCLR,Compare 2 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 9. "CMP_LO1_ISCLR,Compare 1 low Interrupt clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 8. "CMP_LO0_ISCLR,Compare 0 low Interrupt clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 7. "CMP_LO7_STSCLR,Compare 7 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 6. "CMP_LO6_STSCLR,Compare 6 low Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP_LO5_STSCLR,Compare 5 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 4. "CMP_LO4_STSCLR,Compare 4 low Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 3. "CMP_LO3_STSCLR,Compare 3 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 2. "CMP_LO2_STSCLR,Compare 2 low Status clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP_LO1_STSCLR,Compare 1 low Status clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x0 0. "CMP_LO0_STSCLR,Compare 0 low Status clear" "0: no effect,1: status clear"
|
|
line.long 0x4 "CMPSTATSET,Compare Status Clear Register"
|
|
bitfld.long 0x4 31. "CMP_UP7_ISSET,Compare 7 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 30. "CMP_UP6_ISSET,Compare 6 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 29. "CMP_UP5_ISSET,Compare 5 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 28. "CMP_UP4_ISSET,Compare 4 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 27. "CMP_UP3_ISSET,Compare 3 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 26. "CMP_UP2_ISSET,Compare 2 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 25. "CMP_UP1_ISSET,Compare 1 up Interrupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 24. "CMP_UP0_ISSET,Compare 0 up Interrupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 23. "CMP_UP7_STSSET,Compare 7 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 22. "CMP_UP6_STSSET,Compare 6 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 21. "CMP_UP5_STSSET,Compare 5 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 20. "CMP_UP4_STSSET,Compare 4 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 19. "CMP_UP3_STSSET,Compare 3 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 18. "CMP_UP2_STSSET,Compare 2 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 17. "CMP_UP1_STSSET,Compare 1 up Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 16. "CMP_UP0_STSSET,Compare 0 up Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 15. "CMP_LO7_ISSET,Compare 7 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 14. "CMP_LO6_ISSET,Compare 6 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 13. "CMP_LO5_ISSET,Compare 5 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 12. "CMP_LO4_ISSET,Compare 4 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 11. "CMP_LO3_ISSET,Compare 3 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 10. "CMP_LO2_ISSET,Compare 2 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 9. "CMP_LO1_ISSET,Compare 1 low Interupt set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 8. "CMP_LO0_ISSET,Compare 0 low Interupt set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 7. "CMP_LO7_STSSET,Compare 7 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 6. "CMP_LO6_STSSET,Compare 6 low Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 5. "CMP_LO5_STSSET,Compare 5 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 4. "CMP_LO4_STSSET,Compare 4 low Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 3. "CMP_LO3_STSSET,Compare 3 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 2. "CMP_LO2_STSSET,Compare 2 low Status set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x4 1. "CMP_LO1_STSSET,Compare 1 low Status set" "0: no effect,1: status set"
|
|
bitfld.long 0x4 0. "CMP_LO0_STSSET,Compare 0 low Status set" "0: no effect,1: status set"
|
|
group.long 0x178++0xF
|
|
line.long 0x0 "CONVCFG0,Conversion Configuration Register 0"
|
|
hexmask.long.byte 0x0 4.--7. 1. "STC,Sample Time config"
|
|
line.long 0x4 "CONVCFG1,Conversion Configuration Register 1"
|
|
hexmask.long.byte 0x4 4.--7. 1. "STC,Sample Time config"
|
|
line.long 0x8 "CONVCFG2,Conversion Configuration Register 2"
|
|
hexmask.long.byte 0x8 4.--7. 1. "STC,Sample Time config"
|
|
line.long 0xC "CONVCFG3,Conversion Configuration Register 3"
|
|
hexmask.long.byte 0xC 4.--7. 1. "STC,Sample Time config"
|
|
rgroup.long 0x30++0x1F
|
|
line.long 0x0 "FIL0,Filter Result Register"
|
|
hexmask.long.word 0x0 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x4 "FIL1,Filter Result Register"
|
|
hexmask.long.word 0x4 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x8 "FIL2,Filter Result Register"
|
|
hexmask.long.word 0x8 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0xC "FIL3,Filter Result Register"
|
|
hexmask.long.word 0xC 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x10 "FIL4,Filter Result Register"
|
|
hexmask.long.word 0x10 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x14 "FIL5,Filter Result Register"
|
|
hexmask.long.word 0x14 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x18 "FIL6,Filter Result Register"
|
|
hexmask.long.word 0x18 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
line.long 0x1C "FIL7,Filter Result Register"
|
|
hexmask.long.word 0x1C 0.--13. 1. "FILRESULT,Filter Result Value"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "FILSTAT,Filter Status Register"
|
|
bitfld.long 0x0 7. "FIL7,Filter 7 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 6. "FIL6,Filter 6 Event flag" "0: event not set,1: event set"
|
|
newline
|
|
bitfld.long 0x0 5. "FIL5,Filter 5 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 4. "FIL4,Filter 4 Event flag" "0: event not set,1: event set"
|
|
newline
|
|
bitfld.long 0x0 3. "FIL3,Filter 3 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 2. "FIL2,Filter 2 Event flag" "0: event not set,1: event set"
|
|
newline
|
|
bitfld.long 0x0 1. "FIL1,Filter 1 Event flag" "0: event not set,1: event set"
|
|
bitfld.long 0x0 0. "FIL0,Filter 0 Event flag" "0: event not set,1: event set"
|
|
wgroup.long 0x54++0x7
|
|
line.long 0x0 "FILSTATCLR,Filter Status Clear Register"
|
|
bitfld.long 0x0 7. "FIL7CLR,Filter 7 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 6. "FIL6CLR,Filter 6 Event flag clear" "0: no effect,1: event clear"
|
|
newline
|
|
bitfld.long 0x0 5. "FIL5CLR,Filter 5 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 4. "FIL4CLR,Filter 4 Event flag clear" "0: no effect,1: event clear"
|
|
newline
|
|
bitfld.long 0x0 3. "FIL3CLR,Filter 3 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 2. "FIL2CLR,Filter 2 Event flag clear" "0: no effect,1: event clear"
|
|
newline
|
|
bitfld.long 0x0 1. "FIL1CLR,Filter 1 Event flag clear" "0: no effect,1: event clear"
|
|
bitfld.long 0x0 0. "FIL0CLR,Filter 0 Event flag clear" "0: no effect,1: event clear"
|
|
line.long 0x4 "FILSTATSET,Filter Status Clear Register"
|
|
bitfld.long 0x4 7. "FIL7SET,Filter 7 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 6. "FIL6SET,Filter 6 Event flag set" "0: no effect,1: event set"
|
|
newline
|
|
bitfld.long 0x4 5. "FIL5SET,Filter 5 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 4. "FIL4SET,Filter 4 Event flag set" "0: no effect,1: event set"
|
|
newline
|
|
bitfld.long 0x4 3. "FIL3SET,Filter 3 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 2. "FIL2SET,Filter 2 Event flag set" "0: no effect,1: event set"
|
|
newline
|
|
bitfld.long 0x4 1. "FIL1SET,Filter 1 Event flag set" "0: no effect,1: event set"
|
|
bitfld.long 0x4 0. "FIL0SET,Filter 0 Event flag set" "0: no effect,1: event set"
|
|
group.long 0x1A8++0x3
|
|
line.long 0x0 "FILTCFG,Filter Configuration"
|
|
bitfld.long 0x0 28.--29. "COEF_A7,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 24.--25. "COEF_A6,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
newline
|
|
bitfld.long 0x0 20.--21. "COEF_A5,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 16.--17. "COEF_A4,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "COEF_A3,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 8.--9. "COEF_A2,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "COEF_A1,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
bitfld.long 0x0 0.--1. "COEF_A0,Filter Coefficient 0" "0: Filter coefficient 1/2,1: Filter coefficient 1/4,2: Filter coefficient 1/8,3: Filter coefficient 1/16"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "GLOBCONF,Global Configuration Register"
|
|
bitfld.long 0x0 2. "ISTE,Idle shadow transfer enable" "0: Shadow transfer done based on selected shadow..,1: Shadow transfer is automatically enabled when no.."
|
|
bitfld.long 0x0 0. "EN,Module Enable" "0: ADC2 Module is disabled,1: ADC2 Module is enabled"
|
|
group.long 0xA4++0x13
|
|
line.long 0x0 "IEN0,Interrupt Enable Register 0"
|
|
bitfld.long 0x0 14. "IEN_CH14,Channel 14 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 13. "IEN_CH13,Channel 13 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 12. "IEN_CH12,Channel 12 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 11. "IEN_CH11,Channel 11 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 10. "IEN_CH10,Channel 10 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 9. "IEN_CH9,Channel 9 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 8. "IEN_CH8,Channel 8 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 7. "IEN_CH7,Channel 7 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 6. "IEN_CH6,Channel 6 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 5. "IEN_CH5,Channel 5 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 4. "IEN_CH4,Channel 4 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 3. "IEN_CH3,Channel 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 2. "IEN_CH2,Channel 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x0 1. "IEN_CH1,Channel 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x0 0. "IEN_CH0,Channel 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
line.long 0x4 "IEN1,Interrupt Enable Register 1"
|
|
bitfld.long 0x4 31. "IEN_UP7,Compare 7 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 30. "IEN_UP6,Compare 6 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 29. "IEN_UP5,Compare 5 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 28. "IEN_UP4,Compare 4 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 27. "IEN_UP3,Compare 3 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 26. "IEN_UP2,Compare 2 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 25. "IEN_UP1,Compare 1 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 24. "IEN_UP0,Compare 0 UP Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 23. "IEN_LO7,Compare 7 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 22. "IEN_LO6,Compare 6 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 21. "IEN_LO5,Compare 5 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 20. "IEN_LO4,Compare 4 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 19. "IEN_LO3,Compare 3 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 18. "IEN_LO2,Compare 2 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 17. "IEN_LO1,Compare 1 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 16. "IEN_LO0,Compare 0 LO Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 7. "IEN_COLL3,Collision 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 6. "IEN_COLL2,Collision 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 5. "IEN_COLL1,Collision 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 4. "IEN_COLL0,Collision 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 3. "IEN_SQ3,Sequence 3 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 2. "IEN_SQ2,Sequence 2 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
newline
|
|
bitfld.long 0x4 1. "IEN_SQ1,Sequence 1 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
bitfld.long 0x4 0. "IEN_SQ0,Sequence 0 Interrupt Enable" "0: interrupt disable,1: interrupt enable"
|
|
line.long 0x8 "INP0,Interrupt Node Pointer Register 0"
|
|
bitfld.long 0x8 28.--29. "INP_CH14,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 26.--27. "INP_CH13,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 24.--25. "INP_CH12,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 22.--23. "INP_CH11,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 20.--21. "INP_CH10,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 18.--19. "INP_CH9,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 16.--17. "INP_CH8,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 14.--15. "INP_CH7,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 12.--13. "INP_CH6,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 10.--11. "INP_CH5,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 8.--9. "INP_CH4,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 6.--7. "INP_CH3,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 4.--5. "INP_CH2,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x8 2.--3. "INP_CH1,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x8 0.--1. "INP_CH0,Channel Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
line.long 0xC "INP2,Interrupt Node Pointer Register 2"
|
|
bitfld.long 0xC 30.--31. "INP_CMP_UP7,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 28.--29. "INP_CMP_UP6,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 26.--27. "INP_CMP_UP5,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 24.--25. "INP_CMP_UP4,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 22.--23. "INP_CMP_UP3,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 20.--21. "INP_CMP_UP2,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 18.--19. "INP_CMP_UP1,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 16.--17. "INP_CMP_UP0,Compare Up Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 14.--15. "INP_CMP_LO7,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 12.--13. "INP_CMP_LO6,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 10.--11. "INP_CMP_LO5,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 8.--9. "INP_CMP_LO4,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 6.--7. "INP_CMP_LO3,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 4.--5. "INP_CMP_LO2,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0xC 2.--3. "INP_CMP_LO1,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0xC 0.--1. "INP_CMP_LO0,Compare Lo Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
line.long 0x10 "INP3,Interrupt Node Pointer Register 3"
|
|
bitfld.long 0x10 14.--15. "INP_COLL3,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 12.--13. "INP_COLL2,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 10.--11. "INP_COLL1,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 8.--9. "INP_COLL0,Collision Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 6.--7. "INP_SQ3,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 4.--5. "INP_SQ2,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
newline
|
|
bitfld.long 0x10 2.--3. "INP_SQ1,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
bitfld.long 0x10 0.--1. "INP_SQ0,Sequence Interrupt Node Pointer" "0: mapped to IRQ0,1: mapped to IRQ1,2: mapped to IRQ2,3: mapped to IRQ3"
|
|
rgroup.long 0xC8++0x3
|
|
line.long 0x0 "INTSTAT,Internal Configuration Register"
|
|
bitfld.long 0x0 0. "LOW_VOLT_STS,ADC2 low voltage Status" "0: ADC2 is in normal operating condition,1: ADC2 is in Low Voltage operating condition"
|
|
rgroup.long 0x5C++0x7
|
|
line.long 0x0 "RES0,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES1,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--11. 1. "RESULT,Result Value"
|
|
rgroup.long 0x84++0x13
|
|
line.long 0x0 "RES10,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES11,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x8 "RES12,Result Register"
|
|
bitfld.long 0x8 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x8 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0xC "RES13,Result Register"
|
|
bitfld.long 0xC 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0xC 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x10 "RES14,Result Register"
|
|
bitfld.long 0x10 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x10 0.--11. 1. "RESULT,Result Value"
|
|
rgroup.long 0x64++0x1F
|
|
line.long 0x0 "RES2,Result Register"
|
|
bitfld.long 0x0 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x0 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x4 "RES3,Result Register"
|
|
bitfld.long 0x4 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x4 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x8 "RES4,Result Register"
|
|
bitfld.long 0x8 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x8 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0xC "RES5,Result Register"
|
|
bitfld.long 0xC 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0xC 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x10 "RES6,Result Register"
|
|
bitfld.long 0x10 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x10 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x14 "RES7,Result Register"
|
|
bitfld.long 0x14 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x14 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x18 "RES8,Result Register"
|
|
bitfld.long 0x18 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x18 0.--11. 1. "RESULT,Result Value"
|
|
line.long 0x1C "RES9,Result Register"
|
|
bitfld.long 0x1C 15. "VALID,Valid flag" "0: No new result available,1: New result available"
|
|
hexmask.long.word 0x1C 0.--11. 1. "RESULT,Result Value"
|
|
group.long 0xD8++0xF
|
|
line.long 0x0 "SQCFG0,Sequence Configuration Register 0"
|
|
bitfld.long 0x0 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
bitfld.long 0x0 8.--9. "TRGSEL,Trigger Select" "0: Software Trigger,1: External Trigger source A,2: External Trigger source B,?"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x0 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
line.long 0x4 "SQCFG1,Sequence Configuration Register 1"
|
|
bitfld.long 0x4 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
bitfld.long 0x4 8.--9. "TRGSEL,Trigger Select" "0: Software Trigger,1: External Trigger source A,2: External Trigger source B,?"
|
|
newline
|
|
bitfld.long 0x4 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x4 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
line.long 0x8 "SQCFG2,Sequence Configuration Register 2"
|
|
bitfld.long 0x8 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
bitfld.long 0x8 8.--9. "TRGSEL,Trigger Select" "0: Software Trigger,1: External Trigger source A,2: External Trigger source B,?"
|
|
newline
|
|
bitfld.long 0x8 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0x8 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
line.long 0xC "SQCFG3,Sequence Configuration Register 3"
|
|
bitfld.long 0xC 14. "TRGSW,Software Trigger Bit" "0: SQ not triggered,1: SQ is triggered"
|
|
bitfld.long 0xC 8.--9. "TRGSEL,Trigger Select" "0: Software Trigger,1: External Trigger source A,2: External Trigger source B,?"
|
|
newline
|
|
bitfld.long 0xC 4.--5. "SQREP,Sequence repetition" "0: The Sequence is executed 1 time,1: The Sequence is executed 2 times,2: The Sequence is executed 4 times,3: The Sequence is executed 8 times"
|
|
bitfld.long 0xC 0.--2. "SLOTS,Number of used Slots in Sequence" "0: No Slot used - SQ disabled,1: Slots used,2: Slots used,3: Slots used,4: Slots used,5: No Slot used - SQ disabled,6: No Slot used - SQ disabled,7: No Slot used - SQ disabled"
|
|
group.long 0x168++0xF
|
|
line.long 0x0 "SQSLOT0,SQ Channel Slot Register 0"
|
|
hexmask.long.byte 0x0 24.--27. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x0 16.--19. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--11. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x0 0.--3. 1. "CHSEL0,Channel Select"
|
|
line.long 0x4 "SQSLOT1,SQ Channel Slot Register 1"
|
|
hexmask.long.byte 0x4 24.--27. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x4 16.--19. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x4 8.--11. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x4 0.--3. 1. "CHSEL0,Channel Select"
|
|
line.long 0x8 "SQSLOT2,SQ Channel Slot Register 2"
|
|
hexmask.long.byte 0x8 24.--27. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0x8 16.--19. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0x8 8.--11. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0x8 0.--3. 1. "CHSEL0,Channel Select"
|
|
line.long 0xC "SQSLOT3,SQ Channel Slot Register 3"
|
|
hexmask.long.byte 0xC 24.--27. 1. "CHSEL3,Channel Select"
|
|
hexmask.long.byte 0xC 16.--19. 1. "CHSEL2,Channel Select"
|
|
newline
|
|
hexmask.long.byte 0xC 8.--11. 1. "CHSEL1,Channel Select"
|
|
hexmask.long.byte 0xC 0.--3. 1. "CHSEL0,Channel Select"
|
|
group.long 0x10++0xB
|
|
line.long 0x0 "SQSTAT,Sequence Status Register"
|
|
bitfld.long 0x0 16.--18. "SQNUM,Actual Sequence processed" "0: SQ 0 is running,1: SQ1 is running,2: SQ2 is running,3: SQ3 is running,?,?,?,7: No SQ is running"
|
|
bitfld.long 0x0 11. "COLL3,Collision 3 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 10. "COLL2,Collision 2 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 9. "COLL1,Collision 1 Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 8. "COLL0,Collision 0 Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 3. "SQ3,SQ 3 Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 2. "SQ2,SQ 2 Interrupt Status" "0: status not set,1: status set"
|
|
bitfld.long 0x0 1. "SQ1,SQ 1 Interrupt Status" "0: status not set,1: status set"
|
|
newline
|
|
bitfld.long 0x0 0. "SQ0,SQ 0 Interrupt Status" "0: status not set,1: status set"
|
|
line.long 0x4 "SQSTATCLR,Sequence Status Clear Register"
|
|
bitfld.long 0x4 11. "COLL3CLR,Collision 3 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x4 10. "COLL2CLR,Collision 2 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x4 9. "COLL1CLR,Collision 1 Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x4 8. "COLL0CLR,Collision 0 Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x4 3. "SQ3CLR,SQ 3 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x4 2. "SQ2CLR,SQ 2 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
newline
|
|
bitfld.long 0x4 1. "SQ1CLR,SQ 1 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
bitfld.long 0x4 0. "SQ0CLR,SQ 0 Interrupt Status Clear" "0: no effect,1: status clear"
|
|
line.long 0x8 "SQSTATSET,Sequence Status Clear Register"
|
|
bitfld.long 0x8 11. "COLL3SET,Collision 3 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0x8 10. "COLL2SET,Collision 2 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x8 9. "COLL1SET,Collision 1 Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0x8 8. "COLL0SET,Collision 0 Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x8 3. "SQ3SET,SQ 3 Interrupt Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0x8 2. "SQ2SET,SQ 2 Interrupt Status Set" "0: no effect,1: status set"
|
|
newline
|
|
bitfld.long 0x8 1. "SQ1SET,SQ 1 Interrupt Status Set" "0: no effect,1: status set"
|
|
bitfld.long 0x8 0. "SQ0SET,SQ 0 Interrupt Status Set" "0: no effect,1: status set"
|
|
group.long 0x8++0x3
|
|
line.long 0x0 "SUSCTR,Suspend Control Register"
|
|
bitfld.long 0x0 1. "SUSMOD,Suspend Mode" "0: Hard Suspend Mode,1: Soft Suspend Mode"
|
|
bitfld.long 0x0 0. "SUSEN,ADC2 Suspend Enable" "0: ADC2 Suspend Mode is disabled,1: ADC2 Suspend Mode is enabled"
|
|
rgroup.long 0xC++0x3
|
|
line.long 0x0 "SUSSTAT,Suspend Status Register"
|
|
bitfld.long 0x0 0. "STAT,Suspend Mode Status" "0: Suspend Mode is not entered,1: Suspend mode is entered"
|
|
tree.end
|
|
tree.end
|
|
tree "ARVG (Analog Reference Voltage Generation)"
|
|
base ad:0x48038000
|
|
rgroup.long 0x0++0x3
|
|
line.long 0x0 "CFU_STS,CFU status register"
|
|
bitfld.long 0x0 0. "VREF1V2_UP,Reference voltage status" "0: CFU bandgap not started,1: CFU bandgap started"
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "VAREF_CTRL,VAREF control register"
|
|
bitfld.long 0x0 0. "EN,VAREF enable bit" "0: VAREF disabled,1: VAREF enabled"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "VAREF_IEN,VAREF Interrupt Enable Register"
|
|
bitfld.long 0x0 0. "OC_IEN,VAREF Overcurrent (undervoltage) Interrupt Enable" "0: VAREF overcurrent (undervoltage) interrupt..,1: VAREF overcurrent (undervoltage) interrupt enabled"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "VAREF_IRQ,VAREF Interrupt Status Register"
|
|
bitfld.long 0x0 16. "OC_STS,VAREF overcurrent (undervoltage) status flag. The detection circuit monitors VAREF voltage." "0: No overcurrent (undervoltage) event on VAREF,1: An overcurrent (undervoltage) event occurred on.."
|
|
bitfld.long 0x0 0. "OC_IS,VAREF overcurrent (undervoltage) interrupt." "0: VAREF overcurrent (undervoltage) interrupt not..,1: VAREF overcurrent (undervoltage) interrupt.."
|
|
wgroup.long 0xC++0x3
|
|
line.long 0x0 "VAREF_IRQ_CLR,VAREF Interrupt Clear Register"
|
|
bitfld.long 0x0 16. "OC_STS_CLR,VAREF overcurrent (undervoltage) status flag clear" "0: do nothing,1: Clear VAREF overcurrent (undervoltage) status flag"
|
|
bitfld.long 0x0 0. "OC_IS_CLR,VAREF overcurrent (undervoltage) interrupt clear" "0: do nothing,1: Clear VAREF overcurrent (undervoltage) interrupt.."
|
|
wgroup.long 0x8++0x3
|
|
line.long 0x0 "VAREF_IRQ_SET,VAREF Interrupt Set Register"
|
|
bitfld.long 0x0 16. "OC_STS_SET,VAREF overcurrent (undervoltage) status flag set. Setting this bit will trigger a VAREF switch off." "0: do nothing,1: Set VAREF overcurrent (undervoltage) status flag"
|
|
bitfld.long 0x0 0. "OC_IS_SET,VAREF overcurrent (undervoltage) interrupt set" "0: do nothing,1: Set VAREF overcurrent (undervoltage) interrupt.."
|
|
tree.end
|
|
tree "BDRV (Bridge Driver)"
|
|
base ad:0x4000C000
|
|
group.long 0xF8++0x3
|
|
line.long 0x0 "ASEQC,Adaptive sequencer control"
|
|
bitfld.long 0x0 23. "HB3OFFHYSTEN,Half bridge 3 optimizer hysteresis for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 22. "HB3ONHYSTEN,Half bridge 3 optimizer hysteresis for switch-on" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 17. "HB3ASMOFFEN,Half bridge 3 adaptive sequencer for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 16. "HB3ASMONEN,Half bridge 3 adaptive sequencer for switch-on" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 15. "HB2OFFHYSTEN,Half bridge 2 optimizer hysteresis for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 14. "HB2ONHYSTEN,Half bridge 2 optimizer hysteresis for switch-on" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 9. "HB2ASMOFFEN,Half bridge 2 adaptive sequencer for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 8. "HB2ASMONEN,Half bridge 2 adaptive sequencer for switch-on" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 7. "HB1OFFHYSTEN,Half bridge 1 optimizer hysteresis for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 6. "HB1ONHYSTEN,Half bridge 1 optimizer hysteresis for switch-on" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "HB1ASMOFFEN,Half bridge 1 adaptive sequencer for switch-off" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 0. "HB1ASMONEN,Half bridge 1 adaptive sequencer for switch-on" "0: DISABLE,1: ENABLE"
|
|
group.long 0x104++0x3
|
|
line.long 0x0 "ASEQERRCNT,Adaptive sequencer error counter control"
|
|
bitfld.long 0x0 20.--21. "HB3MFERRCNT,Half bridge 3 measurement failure error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 18.--19. "HB3T12ONERRCNT,Half bridge 3 T12ON error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 16.--17. "HB3T1OFFERRCNT,Half bridge 3 T1OFF error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "HB2MFERRCNT,Half bridge 2 measurement failure error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "HB2T12ONERRCNT,Half bridge 2 T12ON error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 8.--9. "HB2T1OFFERRCNT,Half bridge 2 T1OFF error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "HB1MFERRCNT,Half bridge 1 measurement failure error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "HB1T12ONERRCNT,Half bridge 1 T12ON error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "HB1T1OFFERRCNT,Half bridge 1 T1OFF error counter setting" "0: Error flag is set after 2 consecutive events,1: Error flag is set after 4 consecutive events,2: Error flag is set after 8 consecutive events,3: Error flag is set after 15 consecutive events"
|
|
group.long 0x128++0x3
|
|
line.long 0x0 "ASEQOFFADDDLY,Adaptive sequencer additional switch-off delay setting"
|
|
hexmask.long.byte 0x0 20.--23. 1. "HS3T1OFFADDDLY,High-side driver 3 adaptive sequencer T1OFF additional delay setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "LS3T1OFFADDDLY,Low-side driver 3 adaptive sequencer T1OFF additional delay setting"
|
|
newline
|
|
hexmask.long.byte 0x0 12.--15. 1. "HS2T1OFFADDDLY,High-side driver 2 adaptive sequencer T1OFF additional delay setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--11. 1. "LS2T1OFFADDDLY,Low-side driver 2 adaptive sequencer T1OFF additional delay setting"
|
|
newline
|
|
hexmask.long.byte 0x0 4.--7. 1. "HS1T1OFFADDDLY,High-side driver 1 adaptive sequencer T1OFF additional delay setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--3. 1. "LS1T1OFFADDDLY,Low-side driver 1 adaptive sequencer T1OFF additional delay setting"
|
|
group.long 0x124++0x3
|
|
line.long 0x0 "ASEQOFFIMAX,Adaptive sequencer maximum switch-off current setting"
|
|
hexmask.long.byte 0x0 0.--5. 1. "I1OFFMAX,Switch-off phase 1 maximum current setting"
|
|
group.long 0x114++0x3
|
|
line.long 0x0 "ASEQOFFIMIN,Adaptive sequencer minimum switch-off current setting"
|
|
hexmask.long.byte 0x0 0.--5. 1. "I1OFFMIN,Switch-off phase 1 minimum current setting"
|
|
rgroup.long 0x100++0x3
|
|
line.long 0x0 "ASEQOFFSTS,Adaptive sequencer switch-off status"
|
|
bitfld.long 0x0 23. "HB3OFFFAILDRV,Half bridge 3 switch-off failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 20. "HB3OFFMF,Half bridge 3 adaptive sequencer switch-off measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 19. "HB3I1OFFMIN,Half bridge 3 min I1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 18. "HB3T1OFFMIN,Half bridge 3 min T1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 17. "HB3I1OFFMAX,Half bridge 3 max I1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 16. "HB3T1OFFMAX,Half bridge 3 max T1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 15. "HB2OFFFAILDRV,Half bridge 2 switch-off failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 12. "HB2OFFMF,Half bridge 2 adaptive sequencer switch-off measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 11. "HB2I1OFFMIN,Half bridge 2 min I1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 10. "HB2T1OFFMIN,Half bridge 2 min T1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 9. "HB2I1OFFMAX,Half bridge 2 max I1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 8. "HB2T1OFFMAX,Half bridge 2 max T1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 7. "HB1OFFFAILDRV,Half bridge 1 switch-off failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 4. "HB1OFFMF,Half bridge 1 adaptive sequencer switch-off measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 3. "HB1I1OFFMIN,Half bridge 1 min I1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 2. "HB1T1OFFMIN,Half bridge 1 min T1OFF value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 1. "HB1I1OFFMAX,Half bridge 1 max I1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 0. "HB1T1OFFMAX,Half bridge 1 max T1OFF value reached" "0: Max value not reached,1: Max value reached"
|
|
group.long 0x11C++0x3
|
|
line.long 0x0 "ASEQOFFTMAX,Adaptive sequencer maximum switch-off time setting"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T1OFFMAX,Switch-off phase 1 maximum time setting"
|
|
group.long 0x10C++0x3
|
|
line.long 0x0 "ASEQOFFTMIN,Adaptive sequencer minimum switch-off time setting"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T1OFFMIN,Switch-off phase 1 minimum time setting"
|
|
group.long 0x120++0x3
|
|
line.long 0x0 "ASEQONIMAX,Adaptive sequencer maximum switch-on current setting"
|
|
hexmask.long.byte 0x0 0.--5. 1. "I1ONMAX,Switch-on phase 1 maximum current setting"
|
|
group.long 0x110++0x3
|
|
line.long 0x0 "ASEQONIMIN,Adaptive sequencer minimum switch-on current setting"
|
|
hexmask.long.byte 0x0 0.--5. 1. "I1ONMIN,Switch-on phase 1 minimum current setting"
|
|
rgroup.long 0xFC++0x3
|
|
line.long 0x0 "ASEQONSTS,Adaptive sequencer switch-on status"
|
|
bitfld.long 0x0 23. "HB3ONFAILDRV,Half bridge 3 switch-on failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 20. "HB3ONMF,Half bridge 3 adaptive sequencer switch-on measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 19. "HB3I1ONMIN,Half bridge 3 min I1ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 18. "HB3T12ONMIN,Half bridge 3 min T12ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 17. "HB3I1ONMAX,Half bridge 3 max I1ON value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 16. "HB3T12ONMAX,Half bridge 3 max T12ON value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 15. "HB2ONFAILDRV,Half bridge 2 switch-on failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 12. "HB2ONMF,Half bridge 2 adaptive sequencer switch-on measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 11. "HB2I1ONMIN,Half bridge 2 min I1ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 10. "HB2T12ONMIN,Half bridge 2 min T12ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 9. "HB2I1ONMAX,Half bridge 2 max I1ON value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 8. "HB2T12ONMAX,Half bridge 2 max T12ON value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 7. "HB1ONFAILDRV,Half bridge 1 switch-on failed gate driver" "0: Failure occurred with low-side driver active,1: Failure occurred with high-side driver active"
|
|
newline
|
|
bitfld.long 0x0 4. "HB1ONMF,Half bridge 1 adaptive sequencer switch-on measurement failure" "0: No measurement failure,1: Measurement failure"
|
|
newline
|
|
bitfld.long 0x0 3. "HB1I1ONMIN,Half bridge 1 min I1ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 2. "HB1T12ONMIN,Half bridge 1 min T12ON value reached" "0: Min value not reached,1: Min value reached"
|
|
newline
|
|
bitfld.long 0x0 1. "HB1I1ONMAX,Half bridge 1 max I1ON value reached" "0: Max value not reached,1: Max value reached"
|
|
newline
|
|
bitfld.long 0x0 0. "HB1T12ONMAX,Half bridge 1 max T12ON value reached" "0: Max value not reached,1: Max value reached"
|
|
group.long 0x118++0x3
|
|
line.long 0x0 "ASEQONTMAX,Adaptive sequencer maximum switch-on time setting"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T12ONMAX,Switch-on phases 1 and 2 maximum time setting"
|
|
group.long 0x108++0x3
|
|
line.long 0x0 "ASEQONTMIN,Adaptive sequencer minimum switch-on time setting"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T12ONMIN,Switch-on phases 1 and 2 minimum time setting"
|
|
group.long 0x12C++0x3
|
|
line.long 0x0 "BEMFC_CTRL,BEMF comparator control and status"
|
|
rbitfld.long 0x0 27. "PH3_ZC_STS,Phase 3 zero crossing comparator status" "0: Phase voltage is below the average of the other..,1: Phase voltage is above the average of the other.."
|
|
newline
|
|
rbitfld.long 0x0 26. "PH2_ZC_STS,Phase 2 zero crossing comparator status" "0: Phase voltage is below the average of the other..,1: Phase voltage is above the average of the other.."
|
|
newline
|
|
rbitfld.long 0x0 25. "PH1_ZC_STS,Phase 1 zero crossing comparator status" "0: Phase voltage is below the average of the other..,1: Phase voltage is above the average of the other.."
|
|
newline
|
|
bitfld.long 0x0 24. "SW_TRIG,Software trigger for output to timer" "0: Software trigger reset,1: Software trigger set"
|
|
newline
|
|
bitfld.long 0x0 20. "TRIGB_SEL,Deactivate TRIGB as sample pulse source" "0: TRIGB sample input is used,1: TRIGB is not used"
|
|
newline
|
|
bitfld.long 0x0 19. "TRIGA_SEL,Deactivate TRIGA as sample pulse source" "0: TRIGA sample input is used,1: TRIGA is not used"
|
|
newline
|
|
bitfld.long 0x0 18. "IN_SEL,Deactivate INA/B/C as sample pulse sources" "0: INA/B/C sample inputs are used,1: INA/B/C are not used"
|
|
newline
|
|
bitfld.long 0x0 16.--17. "TRIG_SEL,Trigger output selector" "0: Trigger from BEMFC_CTRL.SW_TRIG,1: Trigger from BEMFC_CTRL.PH1_ZC_STS,2: Trigger from BEMFC_CTRL.PH2_ZC_STS,3: Trigger from BEMFC_CTRL.PH3_ZC_STS"
|
|
newline
|
|
bitfld.long 0x0 14. "BLNK_FILT_BYP,Blanking time and demagnetisation filter bypass" "0: Filter enabled,1: Filter bypassed direct signal output"
|
|
newline
|
|
bitfld.long 0x0 13. "DEMAG_FILT_BYP,Demagnetisation filter bypass" "0: Filter enabled,1: Filter bypassed"
|
|
newline
|
|
bitfld.long 0x0 10.--12. "TBLNK_SEL,Blanking time for BEMF comparators" "0: 6 us blanking time,1: 8 us blanking time,2: 12 us blanking time,3: 16 us blanking time,4: 3 us blanking time,?,?,?"
|
|
newline
|
|
bitfld.long 0x0 8.--9. "CMP_TFILT_SEL,Symmetrical spike filter time for BEMF comparators" "0: 1 us filter time,1: 2 us filter time,2: 4 us filter time,3: 8 us filter time"
|
|
newline
|
|
bitfld.long 0x0 6. "PH3_COMP_DIS_SET,Phase 3 comparator output status value if disabled" "0: PH3_ZC_STS is '0' if disabled,1: PH3_ZC_STS is '1' if disabled"
|
|
newline
|
|
bitfld.long 0x0 5. "PH2_COMP_DIS_SET,Phase 2 comparator output status value if disabled" "0: PH2_ZC_STS is '0' if disabled,1: PH2_ZC_STS is '1' if disabled"
|
|
newline
|
|
bitfld.long 0x0 4. "PH1_COMP_DIS_SET,Phase 1 comparator output status value if disabled" "0: PH1_ZC_STS is '0' if disabled,1: PH1_ZC_STS is '1' if disabled"
|
|
newline
|
|
bitfld.long 0x0 2. "PH3_COMP_EN,Phase 3 comparator enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "PH2_COMP_EN,Phase 2 comparator enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 0. "PH1_COMP_EN,Phase 1 comparator enable" "0: DISABLE,1: ENABLE"
|
|
wgroup.long 0x134++0x3
|
|
line.long 0x0 "BEMFC_IRQCLR,BEMF comparator interrupt status clear"
|
|
bitfld.long 0x0 5. "PH3_ZCRISE_ISC,Phase 3 zero crossing rising interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 4. "PH3_ZCFALL_ISC,Phase 3 zero crossing falling interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 3. "PH2_ZCRISE_ISC,Phase 2 zero crossing rising interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 2. "PH2_ZCFALL_ISC,Phase 2 zero crossing falling interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 1. "PH1_ZCRISE_ISC,Phase 1 zero crossing rising interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 0. "PH1_ZCFALL_ISC,Phase 1 zero crossing falling interrupt status clear" "0: KEEP,1: CLEAR"
|
|
group.long 0x13C++0x3
|
|
line.long 0x0 "BEMFC_IRQEN,BEMF comparator interrupt enable"
|
|
bitfld.long 0x0 5. "PH3_ZCRISE_IEN,Phase 3 zero crossing rising interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 4. "PH3_ZCFALL_IEN,Phase 3 zero crossing falling interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 3. "PH2_ZCRISE_IEN,Phase 2 zero crossing rising interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 2. "PH2_ZCFALL_IEN,Phase 2 zero crossing falling interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "PH1_ZCRISE_IEN,Phase 1 zero crossing rising interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 0. "PH1_ZCFALL_IEN,Phase 1 zero crossing falling interrupt enable" "0: DISABLE,1: ENABLE"
|
|
rgroup.long 0x130++0x3
|
|
line.long 0x0 "BEMFC_IRQS,BEMF comparator interrupt status"
|
|
bitfld.long 0x0 5. "PH3_ZCRISE_IS,Phase 3 zero crossing rising interrupt status" "0: No rising zero crossing detected,1: Rising zero crossing detected"
|
|
newline
|
|
bitfld.long 0x0 4. "PH3_ZCFALL_IS,Phase 3 zero crossing falling interrupt status" "0: No falling zero crossing detected,1: Falling zero crossing detected"
|
|
newline
|
|
bitfld.long 0x0 3. "PH2_ZCRISE_IS,Phase 2 zero crossing rising interrupt status" "0: No rising zero crossing detected,1: Rising zero crossing detected"
|
|
newline
|
|
bitfld.long 0x0 2. "PH2_ZCFALL_IS,Phase 2 zero crossing falling interrupt status" "0: No falling zero crossing detected,1: Falling zero crossing detected"
|
|
newline
|
|
bitfld.long 0x0 1. "PH1_ZCRISE_IS,Phase 1 zero crossing rising interrupt status" "0: No rising zero crossing detected,1: Rising zero crossing detected"
|
|
newline
|
|
bitfld.long 0x0 0. "PH1_ZCFALL_IS,Phase 1 zero crossing falling interrupt status" "0: No falling zero crossing detected,1: Falling zero crossing detected"
|
|
wgroup.long 0x138++0x3
|
|
line.long 0x0 "BEMFC_IRQSET,BEMF comparator interrupt status set"
|
|
bitfld.long 0x0 5. "PH3_ZCRISE_ISS,Phase 3 zero crossing rising interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 4. "PH3_ZCFALL_ISS,Phase 3 zero crossing falling interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 3. "PH2_ZCRISE_ISS,Phase 2 zero crossing rising interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 2. "PH2_ZCFALL_ISS,Phase 2 zero crossing falling interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 1. "PH1_ZCRISE_ISS,Phase 1 zero crossing rising interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 0. "PH1_ZCFALL_ISS,Phase 1 zero crossing falling interrupt status set" "0: KEEP,1: SET"
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "CP_CLK_CTRL,Charge pump clock control"
|
|
bitfld.long 0x0 17. "CPCLKDIS_SET,Charge pump clock value if disabled" "0: Charge pump clock is 0 if disabled,1: Charge pump clock is 1 if disabled"
|
|
newline
|
|
bitfld.long 0x0 16. "CPCLK_EN,Charge pump clock enable" "0: Charge pump clock is switched off and has value..,1: Charge pump clock is running"
|
|
newline
|
|
bitfld.long 0x0 13.--14. "F_CP,MSB of CP clock divider" "0: Don't use this setting,1: Frequency range 318 kHz ... 625 kHz,2: Frequency range 211 kHz ... 312 kHz,3: Frequency range 158 kHz ... 208 kHz"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--12. 1. "DITH_UPPER,CP clock divider boundary for upper frequency during dithering"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--4. 1. "DITH_LOWER,CP clock divider boundary for lower frequency during dithering"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "CP_CTRL,Charge pump control"
|
|
bitfld.long 0x0 17. "CP_STG_AUTO,Automatic switch to 1-stage mode and back to 2-stage mode depending on VSD" "0: Fixed stage mode as set in CP_1STAGE,1: stage mode and back to 2-stage mode depending on.."
|
|
newline
|
|
bitfld.long 0x0 16. "CP_1STAGE,Charge pump 1-stage mode select" "0: Double stage mode enabled,1: stage mode select"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "CPLOW_TFILT_SEL,Filter time for charge pump voltage low diagnosis" "0: 4 us filter time,1: 8 us filter time,2: 16 us filter time,3: 32 us filter time"
|
|
newline
|
|
bitfld.long 0x0 9. "VCP_LOWSRC_SEL,Charge pump low voltage detection source select" "0: Charge pump voltage measurement in ADC2 is..,1: Charge pump voltage comparator is selected as UV.."
|
|
newline
|
|
bitfld.long 0x0 8. "VCP_LOWTH2,Charge pump output voltage comparator falling threshold" "0: Threshold 0 for VCP above VSD at 7.5 V,1: Threshold 1 for VCP above VSD at 9.5 V"
|
|
newline
|
|
bitfld.long 0x0 2. "CP_RDY_EN,Bridge driver on charge pump ready enable" "0: Bridge driver can be enabled without charge pump..,1: Bridge driver can only be enabled when charge.."
|
|
newline
|
|
bitfld.long 0x0 0. "CP_EN,Charge pump enable" "0: Charge pump power off,1: Charge pump power on"
|
|
group.long 0x0++0x7
|
|
line.long 0x0 "CTRL1,Bridge driver control 1"
|
|
rbitfld.long 0x0 28. "SUPERR_STS,Supply error status" "0: Supply is in required range,1: Supply error detected; this flag is an OR of the.."
|
|
newline
|
|
bitfld.long 0x0 26. "HS3_DCS_EN,High-side driver 3 diagnosis current source enable" "0: DISABLE,1: Short diagnosis can be performed by evaluating.."
|
|
newline
|
|
bitfld.long 0x0 25. "HS2_DCS_EN,High-side driver 2 diagnosis current source enable" "0: DISABLE,1: Short diagnosis can be performed by evaluating.."
|
|
newline
|
|
bitfld.long 0x0 24. "HS1_DCS_EN,High-side driver 1 diagnosis current source enable" "0: DISABLE,1: Short diagnosis can be performed by evaluating.."
|
|
newline
|
|
bitfld.long 0x0 23. "HS3_OC_SEL,High-side driver 3 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 22. "HS3_ON,High-side driver 3 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_PWM,High-side driver 3 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 19. "LS3_OC_SEL,Low-side driver 3 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 18. "LS3_ON,Low-side driver 3 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_PWM,Low-side driver 3 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 16. "HB3_EN,Half bridge 3 enable" "0: Driver circuit power off,1: Driver circuit power on"
|
|
newline
|
|
bitfld.long 0x0 15. "HS2_OC_SEL,High-side driver 2 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 14. "HS2_ON,High-side driver 2 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_PWM,High-side driver 2 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 11. "LS2_OC_SEL,Low-side driver 2 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 10. "LS2_ON,Low-side driver 2 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_PWM,Low-side driver 2 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 8. "HB2_EN,Half bridge 2 enable" "0: Driver circuit power off,1: Driver circuit power on"
|
|
newline
|
|
bitfld.long 0x0 7. "HS1_OC_SEL,High-side driver 1 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 6. "HS1_ON,High-side driver 1 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_PWM,High-side driver 1 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "LS1_OC_SEL,Low-side driver 1 overcurrent shutdown select" "0: All drivers will be shut down in case of..,1: Only local driver will be shut down in case of.."
|
|
newline
|
|
bitfld.long 0x0 2. "LS1_ON,Low-side driver 1 on" "0: Driver off,1: Driver on"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_PWM,Low-side driver 1 PWM enable" "0: Control by PWM input disabled,1: Control by PWM input enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "HB1_EN,Half bridge 1 enable" "0: Driver circuit power off,1: Driver circuit power on"
|
|
line.long 0x4 "CTRL2,Bridge driver control 2"
|
|
bitfld.long 0x4 31. "DRV_CCP_DIS,Dynamic cross-conduction protection disable" "0: Dynamic CCP is active,1: Dynamic CCP is disabled"
|
|
newline
|
|
bitfld.long 0x4 28.--30. "DRV_CCP_TIMSEL,Minimum cross-conduction protection time setting" "0: 200 ns cross-conduction protection time,1: 400 ns cross-conduction protection time,2: 800 ns cross-conduction protection time,3: 1.6 us cross-conduction protection time,4: 3.2 us cross-conduction protection time,5: 6.4 us cross-conduction protection time,6: 12.8 us cross-conduction protection time,?"
|
|
newline
|
|
bitfld.long 0x4 24.--25. "LS_HS_BT_TFILT_SEL,Blanking time for drain-source monitoring of low-side/high-side drivers" "0: 1 us filter time,1: 2 us filter time,2: 4 us filter time,3: 8 us filter time"
|
|
newline
|
|
bitfld.long 0x4 22.--23. "HSDRV_DS_TFILT_SEL,Filter time for drain-source monitoring of high-side drivers" "0: 1 us filter time,1: 2 us filter time,2: 4 us filter time,3: 8 us filter time"
|
|
newline
|
|
bitfld.long 0x4 20.--21. "LSDRV_DS_TFILT_SEL,Filter time for drain-source monitoring of low-side drivers" "0: 1 us filter time,1: 2 us filter time,2: 4 us filter time,3: 8 us filter time"
|
|
newline
|
|
bitfld.long 0x4 16.--18. "DSMONVTH,Voltage threshold for drain-source monitoring of external MOSFETs" "0: Threshold 0 for VDS at 125 mV,1: Threshold 1 for VDS at 250 mV,2: Threshold 2 for VDS at 500 mV,3: Threshold 3 for VDS at 750 mV,4: Threshold 4 for VDS at 1.00 V,5: Threshold 5 for VDS at 1.25 V,6: Threshold 6 for VDS at 1.50 V,7: Threshold 7 for VDS at 1.75 V"
|
|
newline
|
|
bitfld.long 0x4 12. "ACTDRV_DET_EN,Detection of active / free-wheeling MOSFET" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x4 9. "HB3OFFSEQCNF,Half bridge 3 sequencer switch-off configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
newline
|
|
bitfld.long 0x4 8. "HB3ONSEQCNF,Half bridge 3 sequencer switch-on configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
newline
|
|
bitfld.long 0x4 5. "HB2OFFSEQCNF,Half bridge 2 sequencer switch-off configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
newline
|
|
bitfld.long 0x4 4. "HB2ONSEQCNF,Half bridge 2 sequencer switch-on configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "HB1OFFSEQCNF,Half bridge 1 sequencer switch-off configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "HB1ONSEQCNF,Half bridge 1 sequencer switch-on configuration" "0: Half bridge drivers operate with constant current,1: Sequencer is enabled"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "DLY_DIAG,Delay diagnosis timer"
|
|
bitfld.long 0x0 26. "DLY_DIAG_SSET,External power MOSFET switch-on/-off timer valid flag set" "0: Keep timer status,1: Set timer status"
|
|
newline
|
|
bitfld.long 0x0 25. "DLY_DIAG_SCLR,External power MOSFET switch-on/-off timer valid flag clear" "0: Keep timer status,1: Clear timer status"
|
|
newline
|
|
rbitfld.long 0x0 24. "DLY_DIAG_STS,External power MOSFET switch-on/-off timer valid flag" "0: Timer measurement ongoing,1: Timer measurement finished"
|
|
newline
|
|
bitfld.long 0x0 19. "DLY_DIAG_DIRSEL,External power MOSFET timer on/off select" "0: Measure switch-off time,1: Measure switch-on time"
|
|
newline
|
|
bitfld.long 0x0 16.--18. "DLY_DIAG_CHSEL,External power MOSFET switch-on/-off timer channel select" "0: Switch-on/-off time measurement deactivated,1: Measure low-side driver 1 switch-on/-off delay..,2: Measure low-side driver 2 switch-on/-off delay..,3: Measure low-side driver 3 switch-on/-off delay..,?,5: Measure high-side driver 1 switch-on/-off delay..,6: Measure high-side driver 2 switch-on/-off delay..,7: Measure high-side driver 3 switch-on/-off delay.."
|
|
newline
|
|
hexmask.long.word 0x0 0.--9. 1. "DLY_DIAG_TIM,External power MOSFET switch-on/-off timer result register"
|
|
group.long 0x3C++0x3
|
|
line.long 0x0 "HB1IGATECLMPC,Half bridge 1 gate current clamping value"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB1_ICLMPOFF,Half bridge 1 current clamping value for off state"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HB1_ICLMPON,Half bridge 1 current clamping value for on state"
|
|
group.long 0xE4++0x3
|
|
line.long 0x0 "HB1OFFVAL,Half bridge 1 switch-off measurement values"
|
|
bitfld.long 0x0 31. "HB1_OFFVALVF_SET,Half bridge 1 switch-off measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB1_OFFVALVF_CLR,Half bridge 1 switch-off measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB1_OFFVALVF,Half bridge 1 switch-off measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB1_ACTDRV_OFF,Half bridge 1 switch-off active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB1_TOFFDURMERR,Half bridge 1 switch-off voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB1_TOFFDUR,Half bridge 1 switch-off voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB1_I1OFFVAL,Half bridge 1 switch-off phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB1_TOFFDLY,Half bridge 1 switch-off delay time value measured until VSH voltage starts to change"
|
|
group.long 0xE0++0x3
|
|
line.long 0x0 "HB1ONVAL,Half bridge 1 switch-on measurement values"
|
|
bitfld.long 0x0 31. "HB1_ONVALVF_SET,Half bridge 1 switch-on measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB1_ONVALVF_CLR,Half bridge 1 switch-on measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB1_ONVALVF,Half bridge 1 switch-on measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB1_ACTDRV_ON,Half bridge 1 switch-on active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB1_TONDURMERR,Half bridge 1 switch-on voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB1_TONDUR,Half bridge 1 switch-on voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB1_I1ONVAL,Half bridge 1 switch-on phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB1_TONDLY,Half bridge 1 switch-on delay time value measured until VSH voltage starts to change"
|
|
group.long 0x40++0x3
|
|
line.long 0x0 "HB2IGATECLMPC,Half bridge 2 gate current clamping value"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB2_ICLMPOFF,Half bridge 2 current clamping value for off state"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HB2_ICLMPON,Half bridge 2 current clamping value for on state"
|
|
group.long 0xEC++0x3
|
|
line.long 0x0 "HB2OFFVAL,Half bridge 2 switch-off measurement values"
|
|
bitfld.long 0x0 31. "HB2_OFFVALVF_SET,Half bridge 2 switch-off measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB2_OFFVALVF_CLR,Half bridge 2 switch-off measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_OFFVALVF,Half bridge 2 switch-off measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB2_ACTDRV_OFF,Half bridge 2 switch-off active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB2_TOFFDURMERR,Half bridge 2 switch-off voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB2_TOFFDUR,Half bridge 2 switch-off voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB2_I1OFFVAL,Half bridge 2 switch-off phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB2_TOFFDLY,Half bridge 2 switch-off delay time value measured until VSH voltage starts to change"
|
|
group.long 0xE8++0x3
|
|
line.long 0x0 "HB2ONVAL,Half bridge 2 switch-on measurement values"
|
|
bitfld.long 0x0 31. "HB2_ONVALVF_SET,Half bridge 2 switch-on measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB2_ONVALVF_CLR,Half bridge 2 switch-on measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_ONVALVF,Half bridge 2 switch-on measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB2_ACTDRV_ON,Half bridge 2 switch-on active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB2_TONDURMERR,Half bridge 2 switch-on voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB2_TONDUR,Half bridge 2 switch-on voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB2_I1ONVAL,Half bridge 2 switch-on phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB2_TONDLY,Half bridge 2 switch-on delay time value measured until VSH voltage starts to change"
|
|
group.long 0x44++0x3
|
|
line.long 0x0 "HB3IGATECLMPC,Half bridge 3 gate current clamping value"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB3_ICLMPOFF,Half bridge 3 current clamping value for off state"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HB3_ICLMPON,Half bridge 3 current clamping value for on state"
|
|
group.long 0xF4++0x3
|
|
line.long 0x0 "HB3OFFVAL,Half bridge 3 switch-off measurement values"
|
|
bitfld.long 0x0 31. "HB3_OFFVALVF_SET,Half bridge 3 switch-off measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_OFFVALVF_CLR,Half bridge 3 switch-off measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB3_OFFVALVF,Half bridge 3 switch-off measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB3_ACTDRV_OFF,Half bridge 3 switch-off active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB3_TOFFDURMERR,Half bridge 3 switch-off voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB3_TOFFDUR,Half bridge 3 switch-off voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB3_I1OFFVAL,Half bridge 3 switch-off phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB3_TOFFDLY,Half bridge 3 switch-off delay time value measured until VSH voltage starts to change"
|
|
group.long 0xF0++0x3
|
|
line.long 0x0 "HB3ONVAL,Half bridge 3 switch-on measurement values"
|
|
bitfld.long 0x0 31. "HB3_ONVALVF_SET,Half bridge 3 switch-on measurement values valid flag set" "0: Keep measurement status,1: Set new measurement status"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_ONVALVF_CLR,Half bridge 3 switch-on measurement values valid flag clear" "0: Keep measurement values,1: Query new measurement values"
|
|
newline
|
|
bitfld.long 0x0 29. "HB3_ONVALVF,Half bridge 3 switch-on measurement values valid flag" "0: Measurement values not valid,1: Registers contain valid data"
|
|
newline
|
|
rbitfld.long 0x0 28. "HB3_ACTDRV_ON,Half bridge 3 switch-on active driver" "0: Measurement values from low-side driver,1: Measurement values from high-side driver"
|
|
newline
|
|
rbitfld.long 0x0 22. "HB3_TONDURMERR,Half bridge 3 switch-on voltage slope time measurement error" "0: Slope duration measurement valid,1: Slope duration measurement error"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HB3_TONDUR,Half bridge 3 switch-on voltage slope duration time value"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HB3_I1ONVAL,Half bridge 3 switch-on phase 1 current setting from adaptive sequencer"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HB3_TONDLY,Half bridge 3 switch-on delay time value measured until VSH voltage starts to change"
|
|
group.long 0xDC++0x3
|
|
line.long 0x0 "HCDIS,High-current discharge mode control"
|
|
bitfld.long 0x0 16. "HCDIS_SSO,High-current discharge mode with safe switch-off" "0: No high-current discharge mode in case of safe..,1: In case of safe switch-off all gates are.."
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "IHCDIS,High-current discharge mode current setting for all drivers"
|
|
group.long 0x54++0x3
|
|
line.long 0x0 "HS1AFIC,High-side driver 1 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS1_IAFON,High-side driver 1 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS1_IAFOFF,High-side driver 1 active free-wheeling switch-off current setting"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "HS1AFTC,High-side driver 1 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "HS1_TAFON,High-side driver 1 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS1_TAFOFF,High-side driver 1 active free-wheeling switch-off time setting"
|
|
group.long 0x6C++0x3
|
|
line.long 0x0 "HS1SEQOFFIC,High-side driver 1 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS1_I3OFF,High-side driver 1 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS1_I2OFF,High-side driver 1 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS1_I1OFF,High-side driver 1 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0x68++0x3
|
|
line.long 0x0 "HS1SEQOFFTC,High-side driver 1 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS1_T3OFF,High-side driver 1 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS1_T2OFF,High-side driver 1 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS1_T1OFF,High-side driver 1 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0x74++0x3
|
|
line.long 0x0 "HS1SEQONIC,High-side driver 1 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS1_I4ON,High-side driver 1 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS1_I3ON,High-side driver 1 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS1_I2ON,High-side driver 1 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS1_I1ON,High-side driver 1 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0x70++0x3
|
|
line.long 0x0 "HS1SEQONTC,High-side driver 1 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS1_T4ON,High-side driver 1 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS1_T3ON,High-side driver 1 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS1_T2ON,High-side driver 1 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS1_T1ON,High-side driver 1 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
group.long 0x84++0x3
|
|
line.long 0x0 "HS2AFIC,High-side driver 2 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS2_IAFON,High-side driver 2 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS2_IAFOFF,High-side driver 2 active free-wheeling switch-off current setting"
|
|
group.long 0x80++0x3
|
|
line.long 0x0 "HS2AFTC,High-side driver 2 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "HS2_TAFON,High-side driver 2 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS2_TAFOFF,High-side driver 2 active free-wheeling switch-off time setting"
|
|
group.long 0x9C++0x3
|
|
line.long 0x0 "HS2SEQOFFIC,High-side driver 2 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS2_I3OFF,High-side driver 2 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS2_I2OFF,High-side driver 2 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS2_I1OFF,High-side driver 2 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0x98++0x3
|
|
line.long 0x0 "HS2SEQOFFTC,High-side driver 2 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS2_T3OFF,High-side driver 2 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS2_T2OFF,High-side driver 2 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS2_T1OFF,High-side driver 2 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0xA4++0x3
|
|
line.long 0x0 "HS2SEQONIC,High-side driver 2 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS2_I4ON,High-side driver 2 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS2_I3ON,High-side driver 2 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS2_I2ON,High-side driver 2 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS2_I1ON,High-side driver 2 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0xA0++0x3
|
|
line.long 0x0 "HS2SEQONTC,High-side driver 2 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS2_T4ON,High-side driver 2 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS2_T3ON,High-side driver 2 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS2_T2ON,High-side driver 2 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS2_T1ON,High-side driver 2 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
group.long 0xB4++0x3
|
|
line.long 0x0 "HS3AFIC,High-side driver 3 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS3_IAFON,High-side driver 3 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS3_IAFOFF,High-side driver 3 active free-wheeling switch-off current setting"
|
|
group.long 0xB0++0x3
|
|
line.long 0x0 "HS3AFTC,High-side driver 3 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "HS3_TAFON,High-side driver 3 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS3_TAFOFF,High-side driver 3 active free-wheeling switch-off time setting"
|
|
group.long 0xCC++0x3
|
|
line.long 0x0 "HS3SEQOFFIC,High-side driver 3 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS3_I3OFF,High-side driver 3 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS3_I2OFF,High-side driver 3 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS3_I1OFF,High-side driver 3 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0xC8++0x3
|
|
line.long 0x0 "HS3SEQOFFTC,High-side driver 3 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS3_T3OFF,High-side driver 3 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS3_T2OFF,High-side driver 3 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS3_T1OFF,High-side driver 3 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0xD4++0x3
|
|
line.long 0x0 "HS3SEQONIC,High-side driver 3 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS3_I4ON,High-side driver 3 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS3_I3ON,High-side driver 3 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS3_I2ON,High-side driver 3 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "HS3_I1ON,High-side driver 3 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0xD0++0x3
|
|
line.long 0x0 "HS3SEQONTC,High-side driver 3 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "HS3_T4ON,High-side driver 3 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "HS3_T3ON,High-side driver 3 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "HS3_T2ON,High-side driver 3 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "HS3_T1ON,High-side driver 3 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
wgroup.long 0x30++0x3
|
|
line.long 0x0 "IRQCLR,Bridge driver interrupt status clear"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_ISC,Charge pump comparator low voltage interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_ACTDRV_ISC,Half bridge 3 active driver detection interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_ACTDRV_ISC,Half bridge 2 active driver detection interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 28. "HB1_ACTDRV_ISC,Half bridge 1 active driver detection interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 27. "SEQ_ERR_ISC,Driver sequence error interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 26. "HB3_ASEQ_ISC,Half bridge 3 adaptive sequencer interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 25. "HB2_ASEQ_ISC,Half bridge 2 adaptive sequencer interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 24. "HB1_ASEQ_ISC,Half bridge 1 adaptive sequencer interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_ISC,High-side driver 3 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_ISC,External high-side 3 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_ISC,Low-side driver 3 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_ISC,External low-side 3 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_ISC,High-side driver 2 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_ISC,External high-side 2 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_ISC,Low-side driver 2 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_ISC,External low-side 2 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_ISC,High-side driver 1 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_ISC,External high-side 1 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_ISC,Low-side driver 1 off-state drain source monitoring interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_ISC,External low-side 1 MOSFET overcurrent interrupt status clear" "0: KEEP,1: CLEAR"
|
|
group.long 0x38++0x3
|
|
line.long 0x0 "IRQEN,Bridge driver interrupt enable"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_IEN,Charge pump comparator low voltage interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_ACTDRV_IEN,Half bridge 3 active driver detection interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_ACTDRV_IEN,Half bridge 2 active driver detection interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 28. "HB1_ACTDRV_IEN,Half bridge 1 active driver detection interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 27. "SEQ_ERR_IEN,Driver sequence error interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 26. "HB3_ASEQ_IEN,Half bridge 3 adaptive sequencer interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 25. "HB2_ASEQ_IEN,Half bridge 2 adaptive sequencer interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 24. "HB1_ASEQ_IEN,Half bridge 1 adaptive sequencer interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_IEN,High-side driver 3 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_IEN,External high-side 3 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_IEN,Low-side driver 3 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_IEN,External low-side 3 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_IEN,High-side driver 2 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_IEN,External high-side 2 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_IEN,Low-side driver 2 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_IEN,External low-side 2 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_IEN,High-side driver 1 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_IEN,External high-side 1 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_IEN,Low-side driver 1 off-state drain source monitoring interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_IEN,External low-side 1 MOSFET overcurrent interrupt enable" "0: DISABLE,1: ENABLE"
|
|
rgroup.long 0x2C++0x3
|
|
line.long 0x0 "IRQS,Bridge driver interrupt status"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_IS,Charge pump comparator low voltage interrupt status" "0: No undervoltage detected,1: Undervoltage on charge pump output detected"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_ACTDRV_IS,Half bridge 3 active driver detection interrupt status" "0: Active driver did not change,1: Active driver change detected"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_ACTDRV_IS,Half bridge 2 active driver detection interrupt status" "0: Active driver did not change,1: Active driver change detected"
|
|
newline
|
|
bitfld.long 0x0 28. "HB1_ACTDRV_IS,Half bridge 1 active driver detection interrupt status" "0: Active driver did not change,1: Active driver change detected"
|
|
newline
|
|
bitfld.long 0x0 27. "SEQ_ERR_IS,Driver sequence error interrupt status" "0: No cross current,1: High-side and low-side drivers of same half.."
|
|
newline
|
|
bitfld.long 0x0 26. "HB3_ASEQ_IS,Half bridge 3 adaptive sequencer interrupt status" "0: No adaptive sequencer issue detected,1: Adaptive sequencer issue detected"
|
|
newline
|
|
bitfld.long 0x0 25. "HB2_ASEQ_IS,Half bridge 2 adaptive sequencer interrupt status" "0: No adaptive sequencer issue detected,1: Adaptive sequencer issue detected"
|
|
newline
|
|
bitfld.long 0x0 24. "HB1_ASEQ_IS,Half bridge 1 adaptive sequencer interrupt status" "0: No adaptive sequencer issue detected,1: Adaptive sequencer issue detected"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_IS,High-side driver 3 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_IS,External high-side 3 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_IS,Low-side driver 3 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_IS,External low-side 3 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_IS,High-side driver 2 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_IS,External high-side 2 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_IS,Low-side driver 2 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_IS,External low-side 2 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_IS,High-side driver 1 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_IS,External high-side 1 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_IS,Low-side driver 1 off-state drain source monitoring interrupt status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_IS,External low-side 1 MOSFET overcurrent interrupt status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is automatically.."
|
|
wgroup.long 0x34++0x3
|
|
line.long 0x0 "IRQSET,Bridge driver interrupt status set"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_ISS,Charge pump comparator low voltage interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 30. "HB3_ACTDRV_ISS,Half bridge 3 active driver detection interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 29. "HB2_ACTDRV_ISS,Half bridge 2 active driver detection interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 28. "HB1_ACTDRV_ISS,Half bridge 1 active driver detection interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 27. "SEQ_ERR_ISS,Driver sequence error interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 26. "HB3_ASEQ_ISS,Half bridge 3 adaptive sequencer interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 25. "HB2_ASEQ_ISS,Half bridge 2 adaptive sequencer interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 24. "HB1_ASEQ_ISS,Half bridge 1 adaptive sequencer interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_ISS,High-side driver 3 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_ISS,External high-side 3 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_ISS,Low-side driver 3 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_ISS,External low-side 3 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_ISS,High-side driver 2 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_ISS,External high-side 2 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_ISS,Low-side driver 2 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_ISS,External low-side 2 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_ISS,High-side driver 1 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_ISS,External high-side 1 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_ISS,Low-side driver 1 off-state drain source monitoring interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_ISS,External low-side 1 MOSFET overcurrent interrupt status set" "0: KEEP,1: SET"
|
|
group.long 0x4C++0x3
|
|
line.long 0x0 "LS1AFIC,Low-side driver 1 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS1_IAFON,Low-side driver 1 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS1_IAFOFF,Low-side driver 1 active free-wheeling switch-off current setting"
|
|
group.long 0x48++0x3
|
|
line.long 0x0 "LS1AFTC,Low-side driver 1 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "LS1_TAFON,Low-side driver 1 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS1_TAFOFF,Low-side driver 1 active free-wheeling switch-off time setting"
|
|
group.long 0x5C++0x3
|
|
line.long 0x0 "LS1SEQOFFIC,Low-side driver 1 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS1_I3OFF,Low-side driver 1 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS1_I2OFF,Low-side driver 1 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS1_I1OFF,Low-side driver 1 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0x58++0x3
|
|
line.long 0x0 "LS1SEQOFFTC,Low-side driver 1 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS1_T3OFF,Low-side driver 1 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS1_T2OFF,Low-side driver 1 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS1_T1OFF,Low-side driver 1 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0x64++0x3
|
|
line.long 0x0 "LS1SEQONIC,Low-side driver 1 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS1_I4ON,Low-side driver 1 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS1_I3ON,Low-side driver 1 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS1_I2ON,Low-side driver 1 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS1_I1ON,Low-side driver 1 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0x60++0x3
|
|
line.long 0x0 "LS1SEQONTC,Low-side driver 1 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS1_T4ON,Low-side driver 1 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS1_T3ON,Low-side driver 1 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS1_T2ON,Low-side driver 1 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS1_T1ON,Low-side driver 1 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
group.long 0x7C++0x3
|
|
line.long 0x0 "LS2AFIC,Low-side driver 2 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS2_IAFON,Low-side driver 2 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS2_IAFOFF,Low-side driver 2 active free-wheeling switch-off current setting"
|
|
group.long 0x78++0x3
|
|
line.long 0x0 "LS2AFTC,Low-side driver 2 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "LS2_TAFON,Low-side driver 2 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS2_TAFOFF,Low-side driver 2 active free-wheeling switch-off time setting"
|
|
group.long 0x8C++0x3
|
|
line.long 0x0 "LS2SEQOFFIC,Low-side driver 2 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS2_I3OFF,Low-side driver 2 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS2_I2OFF,Low-side driver 2 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS2_I1OFF,Low-side driver 2 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0x88++0x3
|
|
line.long 0x0 "LS2SEQOFFTC,Low-side driver 2 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS2_T3OFF,Low-side driver 2 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS2_T2OFF,Low-side driver 2 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS2_T1OFF,Low-side driver 2 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0x94++0x3
|
|
line.long 0x0 "LS2SEQONIC,Low-side driver 2 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS2_I4ON,Low-side driver 2 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS2_I3ON,Low-side driver 2 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS2_I2ON,Low-side driver 2 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS2_I1ON,Low-side driver 2 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0x90++0x3
|
|
line.long 0x0 "LS2SEQONTC,Low-side driver 2 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS2_T4ON,Low-side driver 2 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS2_T3ON,Low-side driver 2 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS2_T2ON,Low-side driver 2 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS2_T1ON,Low-side driver 2 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
group.long 0xAC++0x3
|
|
line.long 0x0 "LS3AFIC,Low-side driver 3 active free-wheeling current control"
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS3_IAFON,Low-side driver 3 active free-wheeling switch-on current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS3_IAFOFF,Low-side driver 3 active free-wheeling switch-off current setting"
|
|
group.long 0xA8++0x3
|
|
line.long 0x0 "LS3AFTC,Low-side driver 3 active free-wheeling time control"
|
|
hexmask.long.byte 0x0 8.--15. 1. "LS3_TAFON,Low-side driver 3 active free-wheeling switch-on time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS3_TAFOFF,Low-side driver 3 active free-wheeling switch-off time setting"
|
|
group.long 0xBC++0x3
|
|
line.long 0x0 "LS3SEQOFFIC,Low-side driver 3 switch-off current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS3_I3OFF,Low-side driver 3 sequencer switch-off phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS3_I2OFF,Low-side driver 3 sequencer switch-off phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS3_I1OFF,Low-side driver 3 sequencer switch-off phase 1 and constant switch-off current setting"
|
|
group.long 0xB8++0x3
|
|
line.long 0x0 "LS3SEQOFFTC,Low-side driver 3 switch-off time control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS3_T3OFF,Low-side driver 3 sequencer switch-off phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS3_T2OFF,Low-side driver 3 sequencer switch-off phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS3_T1OFF,Low-side driver 3 sequencer switch-off phase 1 and constant switch-off time setting"
|
|
group.long 0xC4++0x3
|
|
line.long 0x0 "LS3SEQONIC,Low-side driver 3 switch-on current control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS3_I4ON,Low-side driver 3 sequencer switch-on phase 4 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS3_I3ON,Low-side driver 3 sequencer switch-on phase 3 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS3_I2ON,Low-side driver 3 sequencer switch-on phase 2 current setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "LS3_I1ON,Low-side driver 3 sequencer switch-on phase 1 and constant switch-on current setting"
|
|
group.long 0xC0++0x3
|
|
line.long 0x0 "LS3SEQONTC,Low-side driver 3 switch-on time control"
|
|
hexmask.long.byte 0x0 24.--29. 1. "LS3_T4ON,Low-side driver 3 sequencer switch-on phase 4 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "LS3_T3ON,Low-side driver 3 sequencer switch-on phase 3 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "LS3_T2ON,Low-side driver 3 sequencer switch-on phase 2 time setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "LS3_T1ON,Low-side driver 3 sequencer switch-on phase 1 and constant switch-on time setting"
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "PROT_CTRL,Protection function control"
|
|
bitfld.long 0x0 28. "DRVx_VSDUP_DIS,Disable driver discharge on VSD high voltage" "0: DRVx discharged on VSD overvoltage,1: DRVx keep state on VSD overvoltage"
|
|
newline
|
|
bitfld.long 0x0 27. "DRVx_VSDLO_DIS,Disable driver discharge on VSD low voltage" "0: DRVx discharged on VSD undervoltage,1: DRVx keep state on VSD undervoltage"
|
|
newline
|
|
bitfld.long 0x0 26. "DRVx_VCPUP_DIS,Disable driver discharge on charge pump high voltage" "0: DRVx discharged on charge pump overvoltage,1: DRVx keep state on charge pump overvoltage"
|
|
newline
|
|
bitfld.long 0x0 25. "DRVx_VCPLO_DIS,Disable driver discharge on charge pump low voltage" "0: DRVx discharged on charge pump undervoltage,1: DRVx keep state on charge pump undervoltage"
|
|
newline
|
|
bitfld.long 0x0 24. "DRVx_VCPLO_SDEN,Driver shutdown on charge pump low voltage" "0: Bridge driver not disabled on charge pump..,1: Bridge driver disabled on charge pump undervoltage"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3DRV_OCSDN_DIS,High-side driver 3 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3DRV_HCDISCHG_DIS,High-side driver 3 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3DRV_OCSDN_DIS,Low-side driver 3 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3DRV_HCDISCHG_DIS,Low-side driver 3 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2DRV_OCSDN_DIS,High-side driver 2 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2DRV_HCDISCHG_DIS,High-side driver 2 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2DRV_OCSDN_DIS,Low-side driver 2 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2DRV_HCDISCHG_DIS,Low-side driver 2 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1DRV_OCSDN_DIS,High-side driver 1 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1DRV_HCDISCHG_DIS,High-side driver 1 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1DRV_OCSDN_DIS,Low-side driver 1 overcurrent shutdown disable" "0: ENABLE,1: DISABLE"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1DRV_HCDISCHG_DIS,Low-side driver 1 high-current discharge disable" "0: ENABLE,1: DISABLE"
|
|
group.long 0x8++0x7
|
|
line.long 0x0 "PWMSRCSEL,PWM source selection"
|
|
bitfld.long 0x0 20.--22. "HS3_SRC_SEL,High-side driver 3 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
newline
|
|
bitfld.long 0x0 16.--18. "LS3_SRC_SEL,Low-side driver 3 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: Inverted PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
newline
|
|
bitfld.long 0x0 12.--14. "HS2_SRC_SEL,High-side driver 2 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
newline
|
|
bitfld.long 0x0 8.--10. "LS2_SRC_SEL,Low-side driver 2 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: Inverted PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "HS1_SRC_SEL,High-side driver 1 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
newline
|
|
bitfld.long 0x0 0.--2. "LS1_SRC_SEL,Low-side driver 1 PWM source selection" "0: PWM control input,1: PWM control input,2: PWM control input,3: Inverted PWM control input,4: PWM control input,5: PWM control input,6: PWM control input,7: PWM control input"
|
|
line.long 0x4 "SEQMAP,Sequencer mapping"
|
|
rbitfld.long 0x4 17. "HB3_ACTDRV,Half bridge 3 active driver detected at switch-on" "0: Low-side driver detected as active,1: High-side driver detected as active"
|
|
newline
|
|
bitfld.long 0x4 16. "HB3_SEQMAP,Half bridge 3 sequencer mapping" "0: Sequencer is mapped to low-side driver,1: Sequencer is mapped to high-side driver"
|
|
newline
|
|
rbitfld.long 0x4 9. "HB2_ACTDRV,Half bridge 2 active driver detected at switch-on" "0: Low-side driver detected as active,1: High-side driver detected as active"
|
|
newline
|
|
bitfld.long 0x4 8. "HB2_SEQMAP,Half bridge 2 sequencer mapping" "0: Sequencer is mapped to low-side driver,1: Sequencer is mapped to high-side driver"
|
|
newline
|
|
rbitfld.long 0x4 1. "HB1_ACTDRV,Half bridge 1 active driver detected at switch-on" "0: Low-side driver detected as active,1: High-side driver detected as active"
|
|
newline
|
|
bitfld.long 0x4 0. "HB1_SEQMAP,Half bridge 1 sequencer mapping" "0: Sequencer is mapped to low-side driver,1: Sequencer is mapped to high-side driver"
|
|
group.long 0xD8++0x3
|
|
line.long 0x0 "SEQOFFT4I4,Sequencer switch-off phase 4 time and current control"
|
|
hexmask.long.byte 0x0 16.--21. 1. "I4OFF,Sequencer switch-off phase 4 current setting for all drivers"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "T4OFF,Sequencer switch-off phase 4 time setting for all drivers"
|
|
rgroup.long 0x20++0x3
|
|
line.long 0x0 "STS,Bridge driver status"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_STS,Charge pump analog comparator low voltage status" "0: No undervoltage detected,1: Undervoltage on charge pump output detected"
|
|
newline
|
|
bitfld.long 0x0 30. "VSD_OV_STS,VSD overvoltage comparator status" "0: No overvoltage condition detected,1: Overvoltage on VSD supply detected in power-down.."
|
|
newline
|
|
bitfld.long 0x0 29. "VSD_CP1ST_STS,VSD measurement status for automatic CP stage selection" "0: VSD range for CP two-stage operation,1: VSD range for CP one-stage operation"
|
|
newline
|
|
bitfld.long 0x0 28. "VSD_UPTH_STS,VSD measurement high voltage status" "0: No overvoltage detected,1: Overvoltage on VSD supply detected"
|
|
newline
|
|
bitfld.long 0x0 27. "VSD_LOTH_STS,VSD measurement low voltage status" "0: No undervoltage detected,1: Undervoltage on VSD supply detected"
|
|
newline
|
|
bitfld.long 0x0 26. "VCP_UPTH_STS,VCP measurement high voltage status" "0: No overvoltage detected,1: Overvoltage on charge pump output detected"
|
|
newline
|
|
bitfld.long 0x0 25. "VCP_LOTH1_STS,VCP measurement low voltage status" "0: No undervoltage detected,1: Undervoltage on charge pump output detected"
|
|
newline
|
|
bitfld.long 0x0 24. "CP_OTSD_STS,Charge pump temperature measurement status" "0: No overtemperature detected,1: Overtemperature in charge pump detected"
|
|
newline
|
|
bitfld.long 0x0 23. "SH3_HIGH_STS,SH3 voltage high comparator status" "0: SH voltage below high comparator threshold,1: SH voltage above high comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 22. "SH3_LOW_STS,SH3 voltage low comparator status" "0: SH voltage below low comparator threshold,1: SH voltage above low comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_STS,High-side driver 3 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_STS,External high-side 3 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_STS,Low-side driver 3 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_STS,External low-side 3 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
newline
|
|
bitfld.long 0x0 15. "SH2_HIGH_STS,SH2 voltage high comparator status" "0: SH voltage below high comparator threshold,1: SH voltage above high comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 14. "SH2_LOW_STS,SH2 voltage low comparator status" "0: SH voltage below low comparator threshold,1: SH voltage above low comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_STS,High-side driver 2 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_STS,External high-side 2 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_STS,Low-side driver 2 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_STS,External low-side 2 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
newline
|
|
bitfld.long 0x0 7. "SH1_HIGH_STS,SH1 voltage high comparator status" "0: SH voltage below high comparator threshold,1: SH voltage above high comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 6. "SH1_LOW_STS,SH1 voltage low comparator status" "0: SH voltage below low comparator threshold,1: SH voltage above low comparator threshold"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_STS,High-side driver 1 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_STS,External high-side 1 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_STS,Low-side driver 1 off-state drain source monitoring status" "0: No failure on external MOSFET detected,1: Failure on external MOSFET detected"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_STS,External low-side 1 MOSFET overcurrent status" "0: No overcurrent condition detected,1: Overcurrent detected; switch is turned off"
|
|
wgroup.long 0x24++0x7
|
|
line.long 0x0 "STSCLR,Bridge driver status clear"
|
|
bitfld.long 0x0 31. "VCP_LOTH2_SC,Charge pump comparator low voltage status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 21. "HS3_DS_SC,High-side driver 3 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 20. "HS3_OC_SC,External high-side 3 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 17. "LS3_DS_SC,Low-side driver 3 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 16. "LS3_OC_SC,External low-side 3 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 13. "HS2_DS_SC,High-side driver 2 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 12. "HS2_OC_SC,External high-side 2 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 9. "LS2_DS_SC,Low-side driver 2 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 8. "LS2_OC_SC,External low-side 2 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 5. "HS1_DS_SC,High-side driver 1 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 4. "HS1_OC_SC,External high-side 1 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 1. "LS1_DS_SC,Low-side driver 1 off-state drain source monitoring status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 0. "LS1_OC_SC,External low-side 1 MOSFET overcurrent status clear" "0: KEEP,1: CLEAR"
|
|
line.long 0x4 "STSSET,Bridge driver status set"
|
|
bitfld.long 0x4 31. "VCP_LOTH2_SS,Charge pump comparator low voltage status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 21. "HS3_DS_SS,High-side driver 3 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 20. "HS3_OC_SS,External high-side 3 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 17. "LS3_DS_SS,Low-side driver 3 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 16. "LS3_OC_SS,External low-side 3 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 13. "HS2_DS_SS,High-side driver 2 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 12. "HS2_OC_SS,External high-side 2 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 9. "LS2_DS_SS,Low-side driver 2 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 8. "LS2_OC_SS,External low-side 2 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 5. "HS1_DS_SS,High-side driver 1 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 4. "HS1_OC_SS,External high-side 1 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 1. "LS1_DS_SS,Low-side driver 1 off-state drain source monitoring status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x4 0. "LS1_OC_SS,External low-side 1 MOSFET overcurrent status set" "0: KEEP,1: SET"
|
|
tree.end
|
|
tree "CACHE"
|
|
base ad:0x48048000
|
|
wgroup.long 0x100++0x3
|
|
line.long 0x0 "CACHE_AC,Cache All Clean Register"
|
|
hexmask.long 0x0 0.--31. 1. "Clean,Clean all valid blocks from the cache"
|
|
wgroup.long 0x118++0x3
|
|
line.long 0x0 "CACHE_BL,Cache Block Lock Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDR,Lock a memory block from a specified address in the cache"
|
|
wgroup.long 0x114++0x3
|
|
line.long 0x0 "CACHE_BT,Cache Block Touch Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDR,Load a memory block from a specified address into the cache"
|
|
wgroup.long 0x11C++0x3
|
|
line.long 0x0 "CACHE_BU,Cache Block Unlock Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDR,Unlock a memory block from a specified address"
|
|
wgroup.long 0x104++0x3
|
|
line.long 0x0 "CACHE_SC,Cache Set Clean Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDR,Clean all valid blocks of one set at a specified address"
|
|
tree.end
|
|
tree "CANMSGOBJ (CAN Message Object)"
|
|
base ad:0x0
|
|
tree "CANMSGOBJ0"
|
|
base ad:0x48010100
|
|
group.long 0xF0C++0x3
|
|
line.long 0x0 "CAN_MOAMR0,Message Object 0 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xF2C++0x3
|
|
line.long 0x0 "CAN_MOAMR1,Message Object 1 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x104C++0x3
|
|
line.long 0x0 "CAN_MOAMR10,Message Object 10 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x106C++0x3
|
|
line.long 0x0 "CAN_MOAMR11,Message Object 11 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x108C++0x3
|
|
line.long 0x0 "CAN_MOAMR12,Message Object 12 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x10AC++0x3
|
|
line.long 0x0 "CAN_MOAMR13,Message Object 13 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x10CC++0x3
|
|
line.long 0x0 "CAN_MOAMR14,Message Object 14 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x10EC++0x3
|
|
line.long 0x0 "CAN_MOAMR15,Message Object 15 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x110C++0x3
|
|
line.long 0x0 "CAN_MOAMR16,Message Object 16 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x112C++0x3
|
|
line.long 0x0 "CAN_MOAMR17,Message Object 17 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x114C++0x3
|
|
line.long 0x0 "CAN_MOAMR18,Message Object 18 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x116C++0x3
|
|
line.long 0x0 "CAN_MOAMR19,Message Object 19 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xF4C++0x3
|
|
line.long 0x0 "CAN_MOAMR2,Message Object 2 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x118C++0x3
|
|
line.long 0x0 "CAN_MOAMR20,Message Object 20 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x11AC++0x3
|
|
line.long 0x0 "CAN_MOAMR21,Message Object 21 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x11CC++0x3
|
|
line.long 0x0 "CAN_MOAMR22,Message Object 22 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x11EC++0x3
|
|
line.long 0x0 "CAN_MOAMR23,Message Object 23 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x120C++0x3
|
|
line.long 0x0 "CAN_MOAMR24,Message Object 24 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x122C++0x3
|
|
line.long 0x0 "CAN_MOAMR25,Message Object 25 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x124C++0x3
|
|
line.long 0x0 "CAN_MOAMR26,Message Object 26 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x126C++0x3
|
|
line.long 0x0 "CAN_MOAMR27,Message Object 27 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x128C++0x3
|
|
line.long 0x0 "CAN_MOAMR28,Message Object 28 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x12AC++0x3
|
|
line.long 0x0 "CAN_MOAMR29,Message Object 29 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xF6C++0x3
|
|
line.long 0x0 "CAN_MOAMR3,Message Object 3 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x12CC++0x3
|
|
line.long 0x0 "CAN_MOAMR30,Message Object 30 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x12EC++0x3
|
|
line.long 0x0 "CAN_MOAMR31,Message Object 31 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xF8C++0x3
|
|
line.long 0x0 "CAN_MOAMR4,Message Object 4 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xFAC++0x3
|
|
line.long 0x0 "CAN_MOAMR5,Message Object 5 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xFCC++0x3
|
|
line.long 0x0 "CAN_MOAMR6,Message Object 6 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xFEC++0x3
|
|
line.long 0x0 "CAN_MOAMR7,Message Object 7 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x100C++0x3
|
|
line.long 0x0 "CAN_MOAMR8,Message Object 8 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0x102C++0x3
|
|
line.long 0x0 "CAN_MOAMR9,Message Object 9 Acceptance Mask Register"
|
|
bitfld.long 0x0 29. "MIDE,Acceptance Mask Bit for Message IDE Bit" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "AM,Acceptance Mask for Message Identifier"
|
|
group.long 0xF18++0x3
|
|
line.long 0x0 "CAN_MOAR0,Message Object 0 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xF38++0x3
|
|
line.long 0x0 "CAN_MOAR1,Message Object 1 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1058++0x3
|
|
line.long 0x0 "CAN_MOAR10,Message Object 10 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1078++0x3
|
|
line.long 0x0 "CAN_MOAR11,Message Object 11 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1098++0x3
|
|
line.long 0x0 "CAN_MOAR12,Message Object 12 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x10B8++0x3
|
|
line.long 0x0 "CAN_MOAR13,Message Object 13 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x10D8++0x3
|
|
line.long 0x0 "CAN_MOAR14,Message Object 14 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x10F8++0x3
|
|
line.long 0x0 "CAN_MOAR15,Message Object 15 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1118++0x3
|
|
line.long 0x0 "CAN_MOAR16,Message Object 16 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1138++0x3
|
|
line.long 0x0 "CAN_MOAR17,Message Object 17 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1158++0x3
|
|
line.long 0x0 "CAN_MOAR18,Message Object 18 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1178++0x3
|
|
line.long 0x0 "CAN_MOAR19,Message Object 19 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xF58++0x3
|
|
line.long 0x0 "CAN_MOAR2,Message Object 2 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1198++0x3
|
|
line.long 0x0 "CAN_MOAR20,Message Object 20 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x11B8++0x3
|
|
line.long 0x0 "CAN_MOAR21,Message Object 21 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x11D8++0x3
|
|
line.long 0x0 "CAN_MOAR22,Message Object 22 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x11F8++0x3
|
|
line.long 0x0 "CAN_MOAR23,Message Object 23 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1218++0x3
|
|
line.long 0x0 "CAN_MOAR24,Message Object 24 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1238++0x3
|
|
line.long 0x0 "CAN_MOAR25,Message Object 25 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1258++0x3
|
|
line.long 0x0 "CAN_MOAR26,Message Object 26 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1278++0x3
|
|
line.long 0x0 "CAN_MOAR27,Message Object 27 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1298++0x3
|
|
line.long 0x0 "CAN_MOAR28,Message Object 28 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x12B8++0x3
|
|
line.long 0x0 "CAN_MOAR29,Message Object 29 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xF78++0x3
|
|
line.long 0x0 "CAN_MOAR3,Message Object 3 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x12D8++0x3
|
|
line.long 0x0 "CAN_MOAR30,Message Object 30 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x12F8++0x3
|
|
line.long 0x0 "CAN_MOAR31,Message Object 31 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xF98++0x3
|
|
line.long 0x0 "CAN_MOAR4,Message Object 4 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xFB8++0x3
|
|
line.long 0x0 "CAN_MOAR5,Message Object 5 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xFD8++0x3
|
|
line.long 0x0 "CAN_MOAR6,Message Object 6 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0xFF8++0x3
|
|
line.long 0x0 "CAN_MOAR7,Message Object 7 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1018++0x3
|
|
line.long 0x0 "CAN_MOAR8,Message Object 8 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
group.long 0x1038++0x3
|
|
line.long 0x0 "CAN_MOAR9,Message Object 9 Arbitration Register"
|
|
bitfld.long 0x0 30.--31. "PRI,Priority Class" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 29. "IDE,Identifier Extension Bit of Message Object n" "0: Const_0,1: Const_1"
|
|
hexmask.long 0x0 0.--28. 1. "ID,CAN Identifier of Message Object n"
|
|
wgroup.long 0xF1C++0x3
|
|
line.long 0x0 "CAN_MOCTR0,Message Object 0 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xF3C++0x3
|
|
line.long 0x0 "CAN_MOCTR1,Message Object 1 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x105C++0x3
|
|
line.long 0x0 "CAN_MOCTR10,Message Object 10 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x107C++0x3
|
|
line.long 0x0 "CAN_MOCTR11,Message Object 11 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x109C++0x3
|
|
line.long 0x0 "CAN_MOCTR12,Message Object 12 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x10BC++0x3
|
|
line.long 0x0 "CAN_MOCTR13,Message Object 13 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x10DC++0x3
|
|
line.long 0x0 "CAN_MOCTR14,Message Object 14 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x10FC++0x3
|
|
line.long 0x0 "CAN_MOCTR15,Message Object 15 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x111C++0x3
|
|
line.long 0x0 "CAN_MOCTR16,Message Object 16 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x113C++0x3
|
|
line.long 0x0 "CAN_MOCTR17,Message Object 17 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x115C++0x3
|
|
line.long 0x0 "CAN_MOCTR18,Message Object 18 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x117C++0x3
|
|
line.long 0x0 "CAN_MOCTR19,Message Object 19 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xF5C++0x3
|
|
line.long 0x0 "CAN_MOCTR2,Message Object 2 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x119C++0x3
|
|
line.long 0x0 "CAN_MOCTR20,Message Object 20 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x11BC++0x3
|
|
line.long 0x0 "CAN_MOCTR21,Message Object 21 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x11DC++0x3
|
|
line.long 0x0 "CAN_MOCTR22,Message Object 22 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x11FC++0x3
|
|
line.long 0x0 "CAN_MOCTR23,Message Object 23 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x121C++0x3
|
|
line.long 0x0 "CAN_MOCTR24,Message Object 24 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x123C++0x3
|
|
line.long 0x0 "CAN_MOCTR25,Message Object 25 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x125C++0x3
|
|
line.long 0x0 "CAN_MOCTR26,Message Object 26 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x127C++0x3
|
|
line.long 0x0 "CAN_MOCTR27,Message Object 27 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x129C++0x3
|
|
line.long 0x0 "CAN_MOCTR28,Message Object 28 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x12BC++0x3
|
|
line.long 0x0 "CAN_MOCTR29,Message Object 29 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xF7C++0x3
|
|
line.long 0x0 "CAN_MOCTR3,Message Object 3 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x12DC++0x3
|
|
line.long 0x0 "CAN_MOCTR30,Message Object 30 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x12FC++0x3
|
|
line.long 0x0 "CAN_MOCTR31,Message Object 31 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xF9C++0x3
|
|
line.long 0x0 "CAN_MOCTR4,Message Object 4 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xFBC++0x3
|
|
line.long 0x0 "CAN_MOCTR5,Message Object 5 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xFDC++0x3
|
|
line.long 0x0 "CAN_MOCTR6,Message Object 6 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0xFFC++0x3
|
|
line.long 0x0 "CAN_MOCTR7,Message Object 7 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x101C++0x3
|
|
line.long 0x0 "CAN_MOCTR8,Message Object 8 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
wgroup.long 0x103C++0x3
|
|
line.long 0x0 "CAN_MOCTR9,Message Object 9 Control Register"
|
|
bitfld.long 0x0 27. "SETDIR,Set Message Direction" "0,1"
|
|
bitfld.long 0x0 26. "SETTXEN1,Set Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 25. "SETTXEN0,Set Transmit Enable 0" "0,1"
|
|
bitfld.long 0x0 24. "SETTXRQ,Set Transmit Request" "0,1"
|
|
bitfld.long 0x0 23. "SETRXEN,Set Receive Enable" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "SETRTSEL,Set Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 21. "SETMSGVAL,Set Message Valid" "0,1"
|
|
bitfld.long 0x0 20. "SETMSGLST,Set Message Lost" "0,1"
|
|
bitfld.long 0x0 19. "SETNEWDAT,Set New Data" "0,1"
|
|
bitfld.long 0x0 18. "SETRXUPD,Set Receive Updating" "0,1"
|
|
newline
|
|
bitfld.long 0x0 17. "SETTXPND,Set Transmit Pending" "0,1"
|
|
bitfld.long 0x0 16. "SETRXPND,Set Receive Pending" "0,1"
|
|
bitfld.long 0x0 11. "RESDIR_SETDIR,Reset Message Direction" "0,1"
|
|
bitfld.long 0x0 10. "RESTXEN1,Reset Transmit Enable 1" "0,1"
|
|
bitfld.long 0x0 9. "RESTXEN0,Reset Transmit Enable 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 8. "RESTXRQ,Reset Transmit Request" "0,1"
|
|
bitfld.long 0x0 7. "RESRXEN,Reset Receive Enable" "0,1"
|
|
bitfld.long 0x0 6. "RESRTSEL,Reset Receive/Transmit Selected" "0,1"
|
|
bitfld.long 0x0 5. "RESMSGVAL,Reset Message Valid" "0,1"
|
|
bitfld.long 0x0 4. "RESMSGLST,Reset Message Lost" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "RESNEWDAT,Reset New Data" "0,1"
|
|
bitfld.long 0x0 2. "RESRXUPD,Reset Receive Updating" "0,1"
|
|
bitfld.long 0x0 1. "RESTXPND,Reset Transmit Pending" "0,1"
|
|
bitfld.long 0x0 0. "RESRXPND,Reset Receive Pending" "0,1"
|
|
group.long 0xF14++0x3
|
|
line.long 0x0 "CAN_MODATAH0,Message Object 0 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xF34++0x3
|
|
line.long 0x0 "CAN_MODATAH1,Message Object 1 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1054++0x3
|
|
line.long 0x0 "CAN_MODATAH10,Message Object 10 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1074++0x3
|
|
line.long 0x0 "CAN_MODATAH11,Message Object 11 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1094++0x3
|
|
line.long 0x0 "CAN_MODATAH12,Message Object 12 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x10B4++0x3
|
|
line.long 0x0 "CAN_MODATAH13,Message Object 13 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x10D4++0x3
|
|
line.long 0x0 "CAN_MODATAH14,Message Object 14 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x10F4++0x3
|
|
line.long 0x0 "CAN_MODATAH15,Message Object 15 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1114++0x3
|
|
line.long 0x0 "CAN_MODATAH16,Message Object 16 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1134++0x3
|
|
line.long 0x0 "CAN_MODATAH17,Message Object 17 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1154++0x3
|
|
line.long 0x0 "CAN_MODATAH18,Message Object 18 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1174++0x3
|
|
line.long 0x0 "CAN_MODATAH19,Message Object 19 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xF54++0x3
|
|
line.long 0x0 "CAN_MODATAH2,Message Object 2 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1194++0x3
|
|
line.long 0x0 "CAN_MODATAH20,Message Object 20 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x11B4++0x3
|
|
line.long 0x0 "CAN_MODATAH21,Message Object 21 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x11D4++0x3
|
|
line.long 0x0 "CAN_MODATAH22,Message Object 22 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x11F4++0x3
|
|
line.long 0x0 "CAN_MODATAH23,Message Object 23 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1214++0x3
|
|
line.long 0x0 "CAN_MODATAH24,Message Object 24 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1234++0x3
|
|
line.long 0x0 "CAN_MODATAH25,Message Object 25 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1254++0x3
|
|
line.long 0x0 "CAN_MODATAH26,Message Object 26 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1274++0x3
|
|
line.long 0x0 "CAN_MODATAH27,Message Object 27 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1294++0x3
|
|
line.long 0x0 "CAN_MODATAH28,Message Object 28 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x12B4++0x3
|
|
line.long 0x0 "CAN_MODATAH29,Message Object 29 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xF74++0x3
|
|
line.long 0x0 "CAN_MODATAH3,Message Object 3 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x12D4++0x3
|
|
line.long 0x0 "CAN_MODATAH30,Message Object 30 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x12F4++0x3
|
|
line.long 0x0 "CAN_MODATAH31,Message Object 31 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xF94++0x3
|
|
line.long 0x0 "CAN_MODATAH4,Message Object 4 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xFB4++0x3
|
|
line.long 0x0 "CAN_MODATAH5,Message Object 5 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xFD4++0x3
|
|
line.long 0x0 "CAN_MODATAH6,Message Object 6 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xFF4++0x3
|
|
line.long 0x0 "CAN_MODATAH7,Message Object 7 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1014++0x3
|
|
line.long 0x0 "CAN_MODATAH8,Message Object 8 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0x1034++0x3
|
|
line.long 0x0 "CAN_MODATAH9,Message Object 9 Data Register High"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB7,Data Byte 7 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB6,Data Byte 6 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB5,Data Byte 5 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB4,Data Byte 4 of Message Object n"
|
|
group.long 0xF10++0x3
|
|
line.long 0x0 "CAN_MODATAL0,Message Object 0 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF30++0x3
|
|
line.long 0x0 "CAN_MODATAL1,Message Object 1 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1050++0x3
|
|
line.long 0x0 "CAN_MODATAL10,Message Object 10 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1070++0x3
|
|
line.long 0x0 "CAN_MODATAL11,Message Object 11 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1090++0x3
|
|
line.long 0x0 "CAN_MODATAL12,Message Object 12 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x10B0++0x3
|
|
line.long 0x0 "CAN_MODATAL13,Message Object 13 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x10D0++0x3
|
|
line.long 0x0 "CAN_MODATAL14,Message Object 14 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x10F0++0x3
|
|
line.long 0x0 "CAN_MODATAL15,Message Object 15 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1110++0x3
|
|
line.long 0x0 "CAN_MODATAL16,Message Object 16 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1130++0x3
|
|
line.long 0x0 "CAN_MODATAL17,Message Object 17 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1150++0x3
|
|
line.long 0x0 "CAN_MODATAL18,Message Object 18 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1170++0x3
|
|
line.long 0x0 "CAN_MODATAL19,Message Object 19 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF50++0x3
|
|
line.long 0x0 "CAN_MODATAL2,Message Object 2 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1190++0x3
|
|
line.long 0x0 "CAN_MODATAL20,Message Object 20 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x11B0++0x3
|
|
line.long 0x0 "CAN_MODATAL21,Message Object 21 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x11D0++0x3
|
|
line.long 0x0 "CAN_MODATAL22,Message Object 22 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x11F0++0x3
|
|
line.long 0x0 "CAN_MODATAL23,Message Object 23 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1210++0x3
|
|
line.long 0x0 "CAN_MODATAL24,Message Object 24 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1230++0x3
|
|
line.long 0x0 "CAN_MODATAL25,Message Object 25 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1250++0x3
|
|
line.long 0x0 "CAN_MODATAL26,Message Object 26 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1270++0x3
|
|
line.long 0x0 "CAN_MODATAL27,Message Object 27 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1290++0x3
|
|
line.long 0x0 "CAN_MODATAL28,Message Object 28 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x12B0++0x3
|
|
line.long 0x0 "CAN_MODATAL29,Message Object 29 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF70++0x3
|
|
line.long 0x0 "CAN_MODATAL3,Message Object 3 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x12D0++0x3
|
|
line.long 0x0 "CAN_MODATAL30,Message Object 30 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x12F0++0x3
|
|
line.long 0x0 "CAN_MODATAL31,Message Object 31 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF90++0x3
|
|
line.long 0x0 "CAN_MODATAL4,Message Object 4 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFB0++0x3
|
|
line.long 0x0 "CAN_MODATAL5,Message Object 5 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFD0++0x3
|
|
line.long 0x0 "CAN_MODATAL6,Message Object 6 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFF0++0x3
|
|
line.long 0x0 "CAN_MODATAL7,Message Object 7 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1010++0x3
|
|
line.long 0x0 "CAN_MODATAL8,Message Object 8 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x1030++0x3
|
|
line.long 0x0 "CAN_MODATAL9,Message Object 9 Data Register Low"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF00++0x3
|
|
line.long 0x0 "CAN_MOFCR0,Message Object 0 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xF20++0x3
|
|
line.long 0x0 "CAN_MOFCR1,Message Object 1 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1040++0x3
|
|
line.long 0x0 "CAN_MOFCR10,Message Object 10 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1060++0x3
|
|
line.long 0x0 "CAN_MOFCR11,Message Object 11 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1080++0x3
|
|
line.long 0x0 "CAN_MOFCR12,Message Object 12 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x10A0++0x3
|
|
line.long 0x0 "CAN_MOFCR13,Message Object 13 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x10C0++0x3
|
|
line.long 0x0 "CAN_MOFCR14,Message Object 14 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x10E0++0x3
|
|
line.long 0x0 "CAN_MOFCR15,Message Object 15 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1100++0x3
|
|
line.long 0x0 "CAN_MOFCR16,Message Object 16 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1120++0x3
|
|
line.long 0x0 "CAN_MOFCR17,Message Object 17 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1140++0x3
|
|
line.long 0x0 "CAN_MOFCR18,Message Object 18 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1160++0x3
|
|
line.long 0x0 "CAN_MOFCR19,Message Object 19 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xF40++0x3
|
|
line.long 0x0 "CAN_MOFCR2,Message Object 2 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1180++0x3
|
|
line.long 0x0 "CAN_MOFCR20,Message Object 20 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x11A0++0x3
|
|
line.long 0x0 "CAN_MOFCR21,Message Object 21 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x11C0++0x3
|
|
line.long 0x0 "CAN_MOFCR22,Message Object 22 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x11E0++0x3
|
|
line.long 0x0 "CAN_MOFCR23,Message Object 23 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1200++0x3
|
|
line.long 0x0 "CAN_MOFCR24,Message Object 24 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1220++0x3
|
|
line.long 0x0 "CAN_MOFCR25,Message Object 25 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1240++0x3
|
|
line.long 0x0 "CAN_MOFCR26,Message Object 26 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1260++0x3
|
|
line.long 0x0 "CAN_MOFCR27,Message Object 27 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1280++0x3
|
|
line.long 0x0 "CAN_MOFCR28,Message Object 28 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x12A0++0x3
|
|
line.long 0x0 "CAN_MOFCR29,Message Object 29 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xF60++0x3
|
|
line.long 0x0 "CAN_MOFCR3,Message Object 3 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x12C0++0x3
|
|
line.long 0x0 "CAN_MOFCR30,Message Object 30 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x12E0++0x3
|
|
line.long 0x0 "CAN_MOFCR31,Message Object 31 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xF80++0x3
|
|
line.long 0x0 "CAN_MOFCR4,Message Object 4 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xFA0++0x3
|
|
line.long 0x0 "CAN_MOFCR5,Message Object 5 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xFC0++0x3
|
|
line.long 0x0 "CAN_MOFCR6,Message Object 6 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xFE0++0x3
|
|
line.long 0x0 "CAN_MOFCR7,Message Object 7 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1000++0x3
|
|
line.long 0x0 "CAN_MOFCR8,Message Object 8 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0x1020++0x3
|
|
line.long 0x0 "CAN_MOFCR9,Message Object 9 Function Control Register"
|
|
hexmask.long.byte 0x0 24.--27. 1. "DLC,Data Length Code"
|
|
bitfld.long 0x0 23. "STT,Single Transmit Trial" "0,1"
|
|
bitfld.long 0x0 22. "SDT,Single Data Transfer" "0,1"
|
|
bitfld.long 0x0 21. "RMM,Transmit Object Remote Monitoring" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 20. "FRREN,Foreign Remote Request Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 18. "OVIE,Overflow Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 17. "TXIE,Transmit Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 16. "RXIE,Receive Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 11. "DATC,Data Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "DLCC,Data Length Code Copy" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "IDC,Identifier Copy" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "GDFS,Gateway Data Frame Send" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "FDF,CAN FD Frame Format" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "BRS,Bit Rate Switch" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--3. 1. "MMC,Message Mode Control"
|
|
group.long 0xF04++0x3
|
|
line.long 0x0 "CAN_MOFGPR0,Message Object 0 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xF24++0x3
|
|
line.long 0x0 "CAN_MOFGPR1,Message Object 1 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1044++0x3
|
|
line.long 0x0 "CAN_MOFGPR10,Message Object 10 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1064++0x3
|
|
line.long 0x0 "CAN_MOFGPR11,Message Object 11 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1084++0x3
|
|
line.long 0x0 "CAN_MOFGPR12,Message Object 12 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x10A4++0x3
|
|
line.long 0x0 "CAN_MOFGPR13,Message Object 13 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x10C4++0x3
|
|
line.long 0x0 "CAN_MOFGPR14,Message Object 14 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x10E4++0x3
|
|
line.long 0x0 "CAN_MOFGPR15,Message Object 15 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1104++0x3
|
|
line.long 0x0 "CAN_MOFGPR16,Message Object 16 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1124++0x3
|
|
line.long 0x0 "CAN_MOFGPR17,Message Object 17 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1144++0x3
|
|
line.long 0x0 "CAN_MOFGPR18,Message Object 18 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1164++0x3
|
|
line.long 0x0 "CAN_MOFGPR19,Message Object 19 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xF44++0x3
|
|
line.long 0x0 "CAN_MOFGPR2,Message Object 2 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1184++0x3
|
|
line.long 0x0 "CAN_MOFGPR20,Message Object 20 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x11A4++0x3
|
|
line.long 0x0 "CAN_MOFGPR21,Message Object 21 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x11C4++0x3
|
|
line.long 0x0 "CAN_MOFGPR22,Message Object 22 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x11E4++0x3
|
|
line.long 0x0 "CAN_MOFGPR23,Message Object 23 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1204++0x3
|
|
line.long 0x0 "CAN_MOFGPR24,Message Object 24 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1224++0x3
|
|
line.long 0x0 "CAN_MOFGPR25,Message Object 25 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1244++0x3
|
|
line.long 0x0 "CAN_MOFGPR26,Message Object 26 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1264++0x3
|
|
line.long 0x0 "CAN_MOFGPR27,Message Object 27 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1284++0x3
|
|
line.long 0x0 "CAN_MOFGPR28,Message Object 28 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x12A4++0x3
|
|
line.long 0x0 "CAN_MOFGPR29,Message Object 29 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xF64++0x3
|
|
line.long 0x0 "CAN_MOFGPR3,Message Object 3 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x12C4++0x3
|
|
line.long 0x0 "CAN_MOFGPR30,Message Object 30 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x12E4++0x3
|
|
line.long 0x0 "CAN_MOFGPR31,Message Object 31 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xF84++0x3
|
|
line.long 0x0 "CAN_MOFGPR4,Message Object 4 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xFA4++0x3
|
|
line.long 0x0 "CAN_MOFGPR5,Message Object 5 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xFC4++0x3
|
|
line.long 0x0 "CAN_MOFGPR6,Message Object 6 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xFE4++0x3
|
|
line.long 0x0 "CAN_MOFGPR7,Message Object 7 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1004++0x3
|
|
line.long 0x0 "CAN_MOFGPR8,Message Object 8 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0x1024++0x3
|
|
line.long 0x0 "CAN_MOFGPR9,Message Object 9 FIFO/Gateway Pointer Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "SEL,Object Select Pointer"
|
|
hexmask.long.byte 0x0 16.--23. 1. "CUR,Current Object Pointer"
|
|
hexmask.long.byte 0x0 8.--15. 1. "TOP,Top Pointer"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BOT,Bottom Pointer"
|
|
group.long 0xF08++0x3
|
|
line.long 0x0 "CAN_MOIPR0,Message Object 0 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xF28++0x3
|
|
line.long 0x0 "CAN_MOIPR1,Message Object 1 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1048++0x3
|
|
line.long 0x0 "CAN_MOIPR10,Message Object 10 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1068++0x3
|
|
line.long 0x0 "CAN_MOIPR11,Message Object 11 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1088++0x3
|
|
line.long 0x0 "CAN_MOIPR12,Message Object 12 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x10A8++0x3
|
|
line.long 0x0 "CAN_MOIPR13,Message Object 13 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x10C8++0x3
|
|
line.long 0x0 "CAN_MOIPR14,Message Object 14 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x10E8++0x3
|
|
line.long 0x0 "CAN_MOIPR15,Message Object 15 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1108++0x3
|
|
line.long 0x0 "CAN_MOIPR16,Message Object 16 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1128++0x3
|
|
line.long 0x0 "CAN_MOIPR17,Message Object 17 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1148++0x3
|
|
line.long 0x0 "CAN_MOIPR18,Message Object 18 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1168++0x3
|
|
line.long 0x0 "CAN_MOIPR19,Message Object 19 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xF48++0x3
|
|
line.long 0x0 "CAN_MOIPR2,Message Object 2 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1188++0x3
|
|
line.long 0x0 "CAN_MOIPR20,Message Object 20 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x11A8++0x3
|
|
line.long 0x0 "CAN_MOIPR21,Message Object 21 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x11C8++0x3
|
|
line.long 0x0 "CAN_MOIPR22,Message Object 22 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x11E8++0x3
|
|
line.long 0x0 "CAN_MOIPR23,Message Object 23 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1208++0x3
|
|
line.long 0x0 "CAN_MOIPR24,Message Object 24 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1228++0x3
|
|
line.long 0x0 "CAN_MOIPR25,Message Object 25 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1248++0x3
|
|
line.long 0x0 "CAN_MOIPR26,Message Object 26 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1268++0x3
|
|
line.long 0x0 "CAN_MOIPR27,Message Object 27 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1288++0x3
|
|
line.long 0x0 "CAN_MOIPR28,Message Object 28 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x12A8++0x3
|
|
line.long 0x0 "CAN_MOIPR29,Message Object 29 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xF68++0x3
|
|
line.long 0x0 "CAN_MOIPR3,Message Object 3 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x12C8++0x3
|
|
line.long 0x0 "CAN_MOIPR30,Message Object 30 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x12E8++0x3
|
|
line.long 0x0 "CAN_MOIPR31,Message Object 31 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xF88++0x3
|
|
line.long 0x0 "CAN_MOIPR4,Message Object 4 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xFA8++0x3
|
|
line.long 0x0 "CAN_MOIPR5,Message Object 5 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xFC8++0x3
|
|
line.long 0x0 "CAN_MOIPR6,Message Object 6 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0xFE8++0x3
|
|
line.long 0x0 "CAN_MOIPR7,Message Object 7 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1008++0x3
|
|
line.long 0x0 "CAN_MOIPR8,Message Object 8 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
group.long 0x1028++0x3
|
|
line.long 0x0 "CAN_MOIPR9,Message Object 9 Interrupt Pointer Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "CFCVAL,CAN Frame Counter Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MPN,Message Pending Number"
|
|
hexmask.long.byte 0x0 4.--7. 1. "TXINP,Transmit Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "RXINP,Receive Interrupt Node Pointer"
|
|
rgroup.long 0xF1C++0x3
|
|
line.long 0x0 "CAN_MOSTAT0,Message Object 0 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xF3C++0x3
|
|
line.long 0x0 "CAN_MOSTAT1,Message Object 1 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x105C++0x3
|
|
line.long 0x0 "CAN_MOSTAT10,Message Object 10 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x107C++0x3
|
|
line.long 0x0 "CAN_MOSTAT11,Message Object 11 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x109C++0x3
|
|
line.long 0x0 "CAN_MOSTAT12,Message Object 12 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x10BC++0x3
|
|
line.long 0x0 "CAN_MOSTAT13,Message Object 13 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x10DC++0x3
|
|
line.long 0x0 "CAN_MOSTAT14,Message Object 14 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x10FC++0x3
|
|
line.long 0x0 "CAN_MOSTAT15,Message Object 15 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x111C++0x3
|
|
line.long 0x0 "CAN_MOSTAT16,Message Object 16 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x113C++0x3
|
|
line.long 0x0 "CAN_MOSTAT17,Message Object 17 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x115C++0x3
|
|
line.long 0x0 "CAN_MOSTAT18,Message Object 18 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x117C++0x3
|
|
line.long 0x0 "CAN_MOSTAT19,Message Object 19 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xF5C++0x3
|
|
line.long 0x0 "CAN_MOSTAT2,Message Object 2 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x119C++0x3
|
|
line.long 0x0 "CAN_MOSTAT20,Message Object 20 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x11BC++0x3
|
|
line.long 0x0 "CAN_MOSTAT21,Message Object 21 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x11DC++0x3
|
|
line.long 0x0 "CAN_MOSTAT22,Message Object 22 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x11FC++0x3
|
|
line.long 0x0 "CAN_MOSTAT23,Message Object 23 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x121C++0x3
|
|
line.long 0x0 "CAN_MOSTAT24,Message Object 24 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x123C++0x3
|
|
line.long 0x0 "CAN_MOSTAT25,Message Object 25 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x125C++0x3
|
|
line.long 0x0 "CAN_MOSTAT26,Message Object 26 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x127C++0x3
|
|
line.long 0x0 "CAN_MOSTAT27,Message Object 27 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x129C++0x3
|
|
line.long 0x0 "CAN_MOSTAT28,Message Object 28 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x12BC++0x3
|
|
line.long 0x0 "CAN_MOSTAT29,Message Object 29 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xF7C++0x3
|
|
line.long 0x0 "CAN_MOSTAT3,Message Object 3 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x12DC++0x3
|
|
line.long 0x0 "CAN_MOSTAT30,Message Object 30 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x12FC++0x3
|
|
line.long 0x0 "CAN_MOSTAT31,Message Object 31 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xF9C++0x3
|
|
line.long 0x0 "CAN_MOSTAT4,Message Object 4 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xFBC++0x3
|
|
line.long 0x0 "CAN_MOSTAT5,Message Object 5 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xFDC++0x3
|
|
line.long 0x0 "CAN_MOSTAT6,Message Object 6 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0xFFC++0x3
|
|
line.long 0x0 "CAN_MOSTAT7,Message Object 7 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x101C++0x3
|
|
line.long 0x0 "CAN_MOSTAT8,Message Object 8 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
rgroup.long 0x103C++0x3
|
|
line.long 0x0 "CAN_MOSTAT9,Message Object 9 Status Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PNEXT,Pointer to Next Message Object"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PPREV,Pointer to Previous Message Object"
|
|
hexmask.long.byte 0x0 12.--15. 1. "LIST,List Allocation"
|
|
bitfld.long 0x0 11. "DIR,Message Direction" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "TXEN1,Transmit Enable 1" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "TXEN0,Transmit Enable 0" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "TXRQ,Transmit Request" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "RXEN,Receive Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "RTSEL,Receive/Transmit Selected" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "MSGVAL,Message Valid" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "MSGLST,Message Lost" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "NEWDAT,New Data" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "RXUPD,Receive Updating" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TXPND,Transmit Pending" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "RXPND,Receive Pending" "0: Const_0,1: Const_1"
|
|
tree.end
|
|
tree "CANMSGOBJ1"
|
|
base ad:0x48010400
|
|
group.long 0xC00++0x1B
|
|
line.long 0x0 "CAN_EMO0DATA0,Extended Message Object 0 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO0DATA1,Extended Message Object 0 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO0DATA2,Extended Message Object 0 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO0DATA3,Extended Message Object 0 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO0DATA4,Extended Message Object 0 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO0DATA5,Extended Message Object 0 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO0DATA6,Extended Message Object 0 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xD40++0x1B
|
|
line.long 0x0 "CAN_EMO10DATA0,Extended Message Object 10 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO10DATA1,Extended Message Object 10 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO10DATA2,Extended Message Object 10 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO10DATA3,Extended Message Object 10 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO10DATA4,Extended Message Object 10 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO10DATA5,Extended Message Object 10 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO10DATA6,Extended Message Object 10 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xD60++0x1B
|
|
line.long 0x0 "CAN_EMO11DATA0,Extended Message Object 11 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO11DATA1,Extended Message Object 11 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO11DATA2,Extended Message Object 11 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO11DATA3,Extended Message Object 11 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO11DATA4,Extended Message Object 11 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO11DATA5,Extended Message Object 11 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO11DATA6,Extended Message Object 11 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xD80++0x1B
|
|
line.long 0x0 "CAN_EMO12DATA0,Extended Message Object 12 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO12DATA1,Extended Message Object 12 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO12DATA2,Extended Message Object 12 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO12DATA3,Extended Message Object 12 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO12DATA4,Extended Message Object 12 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO12DATA5,Extended Message Object 12 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO12DATA6,Extended Message Object 12 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xDA0++0x1B
|
|
line.long 0x0 "CAN_EMO13DATA0,Extended Message Object 13 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO13DATA1,Extended Message Object 13 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO13DATA2,Extended Message Object 13 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO13DATA3,Extended Message Object 13 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO13DATA4,Extended Message Object 13 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO13DATA5,Extended Message Object 13 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO13DATA6,Extended Message Object 13 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xDC0++0x1B
|
|
line.long 0x0 "CAN_EMO14DATA0,Extended Message Object 14 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO14DATA1,Extended Message Object 14 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO14DATA2,Extended Message Object 14 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO14DATA3,Extended Message Object 14 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO14DATA4,Extended Message Object 14 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO14DATA5,Extended Message Object 14 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO14DATA6,Extended Message Object 14 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xDE0++0x1B
|
|
line.long 0x0 "CAN_EMO15DATA0,Extended Message Object 15 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO15DATA1,Extended Message Object 15 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO15DATA2,Extended Message Object 15 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO15DATA3,Extended Message Object 15 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO15DATA4,Extended Message Object 15 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO15DATA5,Extended Message Object 15 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO15DATA6,Extended Message Object 15 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xE00++0x1B
|
|
line.long 0x0 "CAN_EMO16DATA0,Extended Message Object 16 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO16DATA1,Extended Message Object 16 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO16DATA2,Extended Message Object 16 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO16DATA3,Extended Message Object 16 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO16DATA4,Extended Message Object 16 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO16DATA5,Extended Message Object 16 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO16DATA6,Extended Message Object 16 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xE20++0x1B
|
|
line.long 0x0 "CAN_EMO17DATA0,Extended Message Object 17 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO17DATA1,Extended Message Object 17 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO17DATA2,Extended Message Object 17 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO17DATA3,Extended Message Object 17 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO17DATA4,Extended Message Object 17 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO17DATA5,Extended Message Object 17 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO17DATA6,Extended Message Object 17 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xE40++0x1B
|
|
line.long 0x0 "CAN_EMO18DATA0,Extended Message Object 18 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO18DATA1,Extended Message Object 18 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO18DATA2,Extended Message Object 18 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO18DATA3,Extended Message Object 18 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO18DATA4,Extended Message Object 18 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO18DATA5,Extended Message Object 18 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO18DATA6,Extended Message Object 18 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xE60++0x1B
|
|
line.long 0x0 "CAN_EMO19DATA0,Extended Message Object 19 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO19DATA1,Extended Message Object 19 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO19DATA2,Extended Message Object 19 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO19DATA3,Extended Message Object 19 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO19DATA4,Extended Message Object 19 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO19DATA5,Extended Message Object 19 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO19DATA6,Extended Message Object 19 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xC20++0x1B
|
|
line.long 0x0 "CAN_EMO1DATA0,Extended Message Object 1 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO1DATA1,Extended Message Object 1 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO1DATA2,Extended Message Object 1 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO1DATA3,Extended Message Object 1 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO1DATA4,Extended Message Object 1 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO1DATA5,Extended Message Object 1 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO1DATA6,Extended Message Object 1 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xE80++0x1B
|
|
line.long 0x0 "CAN_EMO20DATA0,Extended Message Object 20 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO20DATA1,Extended Message Object 20 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO20DATA2,Extended Message Object 20 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO20DATA3,Extended Message Object 20 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO20DATA4,Extended Message Object 20 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO20DATA5,Extended Message Object 20 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO20DATA6,Extended Message Object 20 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xEA0++0x1B
|
|
line.long 0x0 "CAN_EMO21DATA0,Extended Message Object 21 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO21DATA1,Extended Message Object 21 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO21DATA2,Extended Message Object 21 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO21DATA3,Extended Message Object 21 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO21DATA4,Extended Message Object 21 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO21DATA5,Extended Message Object 21 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO21DATA6,Extended Message Object 21 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xEC0++0x1B
|
|
line.long 0x0 "CAN_EMO22DATA0,Extended Message Object 22 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO22DATA1,Extended Message Object 22 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO22DATA2,Extended Message Object 22 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO22DATA3,Extended Message Object 22 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO22DATA4,Extended Message Object 22 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO22DATA5,Extended Message Object 22 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO22DATA6,Extended Message Object 22 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xEE0++0x1B
|
|
line.long 0x0 "CAN_EMO23DATA0,Extended Message Object 23 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO23DATA1,Extended Message Object 23 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO23DATA2,Extended Message Object 23 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO23DATA3,Extended Message Object 23 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO23DATA4,Extended Message Object 23 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO23DATA5,Extended Message Object 23 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO23DATA6,Extended Message Object 23 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF00++0x1B
|
|
line.long 0x0 "CAN_EMO24DATA0,Extended Message Object 24 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO24DATA1,Extended Message Object 24 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO24DATA2,Extended Message Object 24 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO24DATA3,Extended Message Object 24 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO24DATA4,Extended Message Object 24 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO24DATA5,Extended Message Object 24 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO24DATA6,Extended Message Object 24 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF20++0x1B
|
|
line.long 0x0 "CAN_EMO25DATA0,Extended Message Object 25 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO25DATA1,Extended Message Object 25 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO25DATA2,Extended Message Object 25 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO25DATA3,Extended Message Object 25 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO25DATA4,Extended Message Object 25 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO25DATA5,Extended Message Object 25 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO25DATA6,Extended Message Object 25 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF40++0x1B
|
|
line.long 0x0 "CAN_EMO26DATA0,Extended Message Object 26 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO26DATA1,Extended Message Object 26 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO26DATA2,Extended Message Object 26 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO26DATA3,Extended Message Object 26 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO26DATA4,Extended Message Object 26 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO26DATA5,Extended Message Object 26 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO26DATA6,Extended Message Object 26 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF60++0x1B
|
|
line.long 0x0 "CAN_EMO27DATA0,Extended Message Object 27 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO27DATA1,Extended Message Object 27 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO27DATA2,Extended Message Object 27 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO27DATA3,Extended Message Object 27 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO27DATA4,Extended Message Object 27 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO27DATA5,Extended Message Object 27 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO27DATA6,Extended Message Object 27 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xF80++0x1B
|
|
line.long 0x0 "CAN_EMO28DATA0,Extended Message Object 28 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO28DATA1,Extended Message Object 28 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO28DATA2,Extended Message Object 28 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO28DATA3,Extended Message Object 28 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO28DATA4,Extended Message Object 28 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO28DATA5,Extended Message Object 28 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO28DATA6,Extended Message Object 28 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFA0++0x1B
|
|
line.long 0x0 "CAN_EMO29DATA0,Extended Message Object 29 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO29DATA1,Extended Message Object 29 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO29DATA2,Extended Message Object 29 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO29DATA3,Extended Message Object 29 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO29DATA4,Extended Message Object 29 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO29DATA5,Extended Message Object 29 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO29DATA6,Extended Message Object 29 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xC40++0x1B
|
|
line.long 0x0 "CAN_EMO2DATA0,Extended Message Object 2 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO2DATA1,Extended Message Object 2 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO2DATA2,Extended Message Object 2 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO2DATA3,Extended Message Object 2 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO2DATA4,Extended Message Object 2 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO2DATA5,Extended Message Object 2 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO2DATA6,Extended Message Object 2 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFC0++0x1B
|
|
line.long 0x0 "CAN_EMO30DATA0,Extended Message Object 30 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO30DATA1,Extended Message Object 30 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO30DATA2,Extended Message Object 30 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO30DATA3,Extended Message Object 30 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO30DATA4,Extended Message Object 30 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO30DATA5,Extended Message Object 30 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO30DATA6,Extended Message Object 30 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xFE0++0x1B
|
|
line.long 0x0 "CAN_EMO31DATA0,Extended Message Object 31 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO31DATA1,Extended Message Object 31 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO31DATA2,Extended Message Object 31 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO31DATA3,Extended Message Object 31 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO31DATA4,Extended Message Object 31 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO31DATA5,Extended Message Object 31 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO31DATA6,Extended Message Object 31 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xC60++0x1B
|
|
line.long 0x0 "CAN_EMO3DATA0,Extended Message Object 3 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO3DATA1,Extended Message Object 3 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO3DATA2,Extended Message Object 3 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO3DATA3,Extended Message Object 3 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO3DATA4,Extended Message Object 3 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO3DATA5,Extended Message Object 3 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO3DATA6,Extended Message Object 3 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xC80++0x1B
|
|
line.long 0x0 "CAN_EMO4DATA0,Extended Message Object 4 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO4DATA1,Extended Message Object 4 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO4DATA2,Extended Message Object 4 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO4DATA3,Extended Message Object 4 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO4DATA4,Extended Message Object 4 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO4DATA5,Extended Message Object 4 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO4DATA6,Extended Message Object 4 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xCA0++0x1B
|
|
line.long 0x0 "CAN_EMO5DATA0,Extended Message Object 5 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO5DATA1,Extended Message Object 5 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO5DATA2,Extended Message Object 5 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO5DATA3,Extended Message Object 5 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO5DATA4,Extended Message Object 5 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO5DATA5,Extended Message Object 5 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO5DATA6,Extended Message Object 5 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xCC0++0x1B
|
|
line.long 0x0 "CAN_EMO6DATA0,Extended Message Object 6 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO6DATA1,Extended Message Object 6 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO6DATA2,Extended Message Object 6 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO6DATA3,Extended Message Object 6 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO6DATA4,Extended Message Object 6 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO6DATA5,Extended Message Object 6 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO6DATA6,Extended Message Object 6 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xCE0++0x1B
|
|
line.long 0x0 "CAN_EMO7DATA0,Extended Message Object 7 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO7DATA1,Extended Message Object 7 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO7DATA2,Extended Message Object 7 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO7DATA3,Extended Message Object 7 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO7DATA4,Extended Message Object 7 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO7DATA5,Extended Message Object 7 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO7DATA6,Extended Message Object 7 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xD00++0x1B
|
|
line.long 0x0 "CAN_EMO8DATA0,Extended Message Object 8 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO8DATA1,Extended Message Object 8 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO8DATA2,Extended Message Object 8 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO8DATA3,Extended Message Object 8 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO8DATA4,Extended Message Object 8 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO8DATA5,Extended Message Object 8 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO8DATA6,Extended Message Object 8 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xD20++0x1B
|
|
line.long 0x0 "CAN_EMO9DATA0,Extended Message Object 9 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO9DATA1,Extended Message Object 9 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO9DATA2,Extended Message Object 9 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO9DATA3,Extended Message Object 9 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO9DATA4,Extended Message Object 9 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO9DATA5,Extended Message Object 9 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO9DATA6,Extended Message Object 9 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
tree.end
|
|
tree "CANMSGOBJ2"
|
|
base ad:0x48010800
|
|
group.long 0x800++0x1B
|
|
line.long 0x0 "CAN_EMO0DATA0,Extended Message Object 0 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO0DATA1,Extended Message Object 0 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO0DATA2,Extended Message Object 0 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO0DATA3,Extended Message Object 0 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO0DATA4,Extended Message Object 0 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO0DATA5,Extended Message Object 0 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO0DATA6,Extended Message Object 0 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x940++0x1B
|
|
line.long 0x0 "CAN_EMO10DATA0,Extended Message Object 10 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO10DATA1,Extended Message Object 10 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO10DATA2,Extended Message Object 10 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO10DATA3,Extended Message Object 10 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO10DATA4,Extended Message Object 10 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO10DATA5,Extended Message Object 10 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO10DATA6,Extended Message Object 10 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x960++0x1B
|
|
line.long 0x0 "CAN_EMO11DATA0,Extended Message Object 11 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO11DATA1,Extended Message Object 11 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO11DATA2,Extended Message Object 11 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO11DATA3,Extended Message Object 11 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO11DATA4,Extended Message Object 11 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO11DATA5,Extended Message Object 11 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO11DATA6,Extended Message Object 11 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x980++0x1B
|
|
line.long 0x0 "CAN_EMO12DATA0,Extended Message Object 12 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO12DATA1,Extended Message Object 12 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO12DATA2,Extended Message Object 12 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO12DATA3,Extended Message Object 12 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO12DATA4,Extended Message Object 12 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO12DATA5,Extended Message Object 12 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO12DATA6,Extended Message Object 12 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x9A0++0x1B
|
|
line.long 0x0 "CAN_EMO13DATA0,Extended Message Object 13 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO13DATA1,Extended Message Object 13 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO13DATA2,Extended Message Object 13 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO13DATA3,Extended Message Object 13 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO13DATA4,Extended Message Object 13 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO13DATA5,Extended Message Object 13 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO13DATA6,Extended Message Object 13 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x9C0++0x1B
|
|
line.long 0x0 "CAN_EMO14DATA0,Extended Message Object 14 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO14DATA1,Extended Message Object 14 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO14DATA2,Extended Message Object 14 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO14DATA3,Extended Message Object 14 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO14DATA4,Extended Message Object 14 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO14DATA5,Extended Message Object 14 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO14DATA6,Extended Message Object 14 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x9E0++0x1B
|
|
line.long 0x0 "CAN_EMO15DATA0,Extended Message Object 15 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO15DATA1,Extended Message Object 15 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO15DATA2,Extended Message Object 15 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO15DATA3,Extended Message Object 15 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO15DATA4,Extended Message Object 15 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO15DATA5,Extended Message Object 15 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO15DATA6,Extended Message Object 15 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xA00++0x1B
|
|
line.long 0x0 "CAN_EMO16DATA0,Extended Message Object 16 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO16DATA1,Extended Message Object 16 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO16DATA2,Extended Message Object 16 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO16DATA3,Extended Message Object 16 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO16DATA4,Extended Message Object 16 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO16DATA5,Extended Message Object 16 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO16DATA6,Extended Message Object 16 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xA20++0x1B
|
|
line.long 0x0 "CAN_EMO17DATA0,Extended Message Object 17 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO17DATA1,Extended Message Object 17 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO17DATA2,Extended Message Object 17 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO17DATA3,Extended Message Object 17 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO17DATA4,Extended Message Object 17 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO17DATA5,Extended Message Object 17 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO17DATA6,Extended Message Object 17 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xA40++0x1B
|
|
line.long 0x0 "CAN_EMO18DATA0,Extended Message Object 18 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO18DATA1,Extended Message Object 18 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO18DATA2,Extended Message Object 18 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO18DATA3,Extended Message Object 18 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO18DATA4,Extended Message Object 18 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO18DATA5,Extended Message Object 18 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO18DATA6,Extended Message Object 18 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xA60++0x1B
|
|
line.long 0x0 "CAN_EMO19DATA0,Extended Message Object 19 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO19DATA1,Extended Message Object 19 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO19DATA2,Extended Message Object 19 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO19DATA3,Extended Message Object 19 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO19DATA4,Extended Message Object 19 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO19DATA5,Extended Message Object 19 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO19DATA6,Extended Message Object 19 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x820++0x1B
|
|
line.long 0x0 "CAN_EMO1DATA0,Extended Message Object 1 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO1DATA1,Extended Message Object 1 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO1DATA2,Extended Message Object 1 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO1DATA3,Extended Message Object 1 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO1DATA4,Extended Message Object 1 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO1DATA5,Extended Message Object 1 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO1DATA6,Extended Message Object 1 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xA80++0x1B
|
|
line.long 0x0 "CAN_EMO20DATA0,Extended Message Object 20 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO20DATA1,Extended Message Object 20 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO20DATA2,Extended Message Object 20 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO20DATA3,Extended Message Object 20 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO20DATA4,Extended Message Object 20 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO20DATA5,Extended Message Object 20 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO20DATA6,Extended Message Object 20 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xAA0++0x1B
|
|
line.long 0x0 "CAN_EMO21DATA0,Extended Message Object 21 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO21DATA1,Extended Message Object 21 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO21DATA2,Extended Message Object 21 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO21DATA3,Extended Message Object 21 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO21DATA4,Extended Message Object 21 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO21DATA5,Extended Message Object 21 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO21DATA6,Extended Message Object 21 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xAC0++0x1B
|
|
line.long 0x0 "CAN_EMO22DATA0,Extended Message Object 22 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO22DATA1,Extended Message Object 22 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO22DATA2,Extended Message Object 22 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO22DATA3,Extended Message Object 22 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO22DATA4,Extended Message Object 22 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO22DATA5,Extended Message Object 22 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO22DATA6,Extended Message Object 22 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xAE0++0x1B
|
|
line.long 0x0 "CAN_EMO23DATA0,Extended Message Object 23 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO23DATA1,Extended Message Object 23 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO23DATA2,Extended Message Object 23 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO23DATA3,Extended Message Object 23 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO23DATA4,Extended Message Object 23 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO23DATA5,Extended Message Object 23 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO23DATA6,Extended Message Object 23 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xB00++0x1B
|
|
line.long 0x0 "CAN_EMO24DATA0,Extended Message Object 24 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO24DATA1,Extended Message Object 24 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO24DATA2,Extended Message Object 24 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO24DATA3,Extended Message Object 24 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO24DATA4,Extended Message Object 24 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO24DATA5,Extended Message Object 24 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO24DATA6,Extended Message Object 24 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xB20++0x1B
|
|
line.long 0x0 "CAN_EMO25DATA0,Extended Message Object 25 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO25DATA1,Extended Message Object 25 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO25DATA2,Extended Message Object 25 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO25DATA3,Extended Message Object 25 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO25DATA4,Extended Message Object 25 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO25DATA5,Extended Message Object 25 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO25DATA6,Extended Message Object 25 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xB40++0x1B
|
|
line.long 0x0 "CAN_EMO26DATA0,Extended Message Object 26 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO26DATA1,Extended Message Object 26 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO26DATA2,Extended Message Object 26 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO26DATA3,Extended Message Object 26 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO26DATA4,Extended Message Object 26 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO26DATA5,Extended Message Object 26 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO26DATA6,Extended Message Object 26 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xB60++0x1B
|
|
line.long 0x0 "CAN_EMO27DATA0,Extended Message Object 27 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO27DATA1,Extended Message Object 27 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO27DATA2,Extended Message Object 27 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO27DATA3,Extended Message Object 27 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO27DATA4,Extended Message Object 27 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO27DATA5,Extended Message Object 27 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO27DATA6,Extended Message Object 27 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xB80++0x1B
|
|
line.long 0x0 "CAN_EMO28DATA0,Extended Message Object 28 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO28DATA1,Extended Message Object 28 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO28DATA2,Extended Message Object 28 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO28DATA3,Extended Message Object 28 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO28DATA4,Extended Message Object 28 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO28DATA5,Extended Message Object 28 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO28DATA6,Extended Message Object 28 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xBA0++0x1B
|
|
line.long 0x0 "CAN_EMO29DATA0,Extended Message Object 29 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO29DATA1,Extended Message Object 29 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO29DATA2,Extended Message Object 29 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO29DATA3,Extended Message Object 29 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO29DATA4,Extended Message Object 29 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO29DATA5,Extended Message Object 29 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO29DATA6,Extended Message Object 29 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x840++0x1B
|
|
line.long 0x0 "CAN_EMO2DATA0,Extended Message Object 2 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO2DATA1,Extended Message Object 2 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO2DATA2,Extended Message Object 2 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO2DATA3,Extended Message Object 2 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO2DATA4,Extended Message Object 2 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO2DATA5,Extended Message Object 2 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO2DATA6,Extended Message Object 2 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xBC0++0x1B
|
|
line.long 0x0 "CAN_EMO30DATA0,Extended Message Object 30 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO30DATA1,Extended Message Object 30 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO30DATA2,Extended Message Object 30 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO30DATA3,Extended Message Object 30 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO30DATA4,Extended Message Object 30 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO30DATA5,Extended Message Object 30 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO30DATA6,Extended Message Object 30 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0xBE0++0x1B
|
|
line.long 0x0 "CAN_EMO31DATA0,Extended Message Object 31 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO31DATA1,Extended Message Object 31 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO31DATA2,Extended Message Object 31 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO31DATA3,Extended Message Object 31 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO31DATA4,Extended Message Object 31 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO31DATA5,Extended Message Object 31 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO31DATA6,Extended Message Object 31 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x860++0x1B
|
|
line.long 0x0 "CAN_EMO3DATA0,Extended Message Object 3 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO3DATA1,Extended Message Object 3 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO3DATA2,Extended Message Object 3 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO3DATA3,Extended Message Object 3 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO3DATA4,Extended Message Object 3 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO3DATA5,Extended Message Object 3 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO3DATA6,Extended Message Object 3 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x880++0x1B
|
|
line.long 0x0 "CAN_EMO4DATA0,Extended Message Object 4 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO4DATA1,Extended Message Object 4 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO4DATA2,Extended Message Object 4 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO4DATA3,Extended Message Object 4 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO4DATA4,Extended Message Object 4 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO4DATA5,Extended Message Object 4 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO4DATA6,Extended Message Object 4 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x8A0++0x1B
|
|
line.long 0x0 "CAN_EMO5DATA0,Extended Message Object 5 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO5DATA1,Extended Message Object 5 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO5DATA2,Extended Message Object 5 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO5DATA3,Extended Message Object 5 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO5DATA4,Extended Message Object 5 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO5DATA5,Extended Message Object 5 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO5DATA6,Extended Message Object 5 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x8C0++0x1B
|
|
line.long 0x0 "CAN_EMO6DATA0,Extended Message Object 6 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO6DATA1,Extended Message Object 6 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO6DATA2,Extended Message Object 6 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO6DATA3,Extended Message Object 6 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO6DATA4,Extended Message Object 6 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO6DATA5,Extended Message Object 6 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO6DATA6,Extended Message Object 6 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x8E0++0x1B
|
|
line.long 0x0 "CAN_EMO7DATA0,Extended Message Object 7 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO7DATA1,Extended Message Object 7 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO7DATA2,Extended Message Object 7 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO7DATA3,Extended Message Object 7 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO7DATA4,Extended Message Object 7 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO7DATA5,Extended Message Object 7 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO7DATA6,Extended Message Object 7 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x900++0x1B
|
|
line.long 0x0 "CAN_EMO8DATA0,Extended Message Object 8 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO8DATA1,Extended Message Object 8 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO8DATA2,Extended Message Object 8 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO8DATA3,Extended Message Object 8 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO8DATA4,Extended Message Object 8 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO8DATA5,Extended Message Object 8 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO8DATA6,Extended Message Object 8 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
group.long 0x920++0x1B
|
|
line.long 0x0 "CAN_EMO9DATA0,Extended Message Object 9 Data 0 Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x0 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x4 "CAN_EMO9DATA1,Extended Message Object 9 Data 1 Register"
|
|
hexmask.long.byte 0x4 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x4 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x8 "CAN_EMO9DATA2,Extended Message Object 9 Data 2 Register"
|
|
hexmask.long.byte 0x8 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x8 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0xC "CAN_EMO9DATA3,Extended Message Object 9 Data 3 Register"
|
|
hexmask.long.byte 0xC 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0xC 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0xC 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0xC 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x10 "CAN_EMO9DATA4,Extended Message Object 9 Data 4 Register"
|
|
hexmask.long.byte 0x10 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x10 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x10 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x10 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x14 "CAN_EMO9DATA5,Extended Message Object 9 Data 5 Register"
|
|
hexmask.long.byte 0x14 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x14 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x14 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x14 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
line.long 0x18 "CAN_EMO9DATA6,Extended Message Object 9 Data 6 Register"
|
|
hexmask.long.byte 0x18 24.--31. 1. "DB3,Data Byte 3 of Message Object n"
|
|
hexmask.long.byte 0x18 16.--23. 1. "DB2,Data Byte 2 of Message Object n"
|
|
hexmask.long.byte 0x18 8.--15. 1. "DB1,Data Byte 1 of Message Object n"
|
|
hexmask.long.byte 0x18 0.--7. 1. "DB0,Data Byte 0 of Message Object n"
|
|
tree.end
|
|
tree.end
|
|
tree "CANNODE (CAN Node)"
|
|
base ad:0x0
|
|
tree "CANNODE"
|
|
base ad:0x48010000
|
|
group.long 0x200++0x3
|
|
line.long 0x0 "CAN_NCR0,Node 0 Control Register"
|
|
bitfld.long 0x0 15. "NISO,Non ISO Operation" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 10. "PED,Protocol Exeption Disable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 9. "FDEN,CAN Flexible Data-Rate Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 7. "CALM,CAN Analyzer Mode" "0,1"
|
|
bitfld.long 0x0 6. "CCE,Configuration Change Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 5. "TXDIS,Transmit Disable" "0,1"
|
|
bitfld.long 0x0 4. "CANDIS,CAN Disable" "0,1"
|
|
bitfld.long 0x0 3. "ALIE,Alert Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "LECIE,LEC Indicated Error Interrupt Enable" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "TRIE,Transfer Interrupt Enable" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 0. "INIT,Node Initialization" "0: Const_0,1: Const_1"
|
|
group.long 0x210++0xB
|
|
line.long 0x0 "CAN_NBTR0,Node 0 Bit Timing Register"
|
|
bitfld.long 0x0 15. "DIV8,Divide Prescaler Clock by 8" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 12.--14. "TSEG2,Time Segment After Sample Point" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TSEG1,Time Segment Before Sample Point"
|
|
bitfld.long 0x0 6.--7. "SJW,(Re) Synchronization Jump Width" "0,1,2,3"
|
|
hexmask.long.byte 0x0 0.--5. 1. "BRP,Baud Rate Prescaler"
|
|
line.long 0x4 "CAN_NECNT0,Node 0 Error Counter Register"
|
|
rbitfld.long 0x4 25. "LEINC,Last Error Increment" "0: Const_0,1: Const_1"
|
|
rbitfld.long 0x4 24. "LETD,Last Error Transfer Direction" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x4 16.--23. 1. "EWRNLVL,Error Warning Level"
|
|
hexmask.long.byte 0x4 8.--15. 1. "TEC,Transmit Error Counter"
|
|
hexmask.long.byte 0x4 0.--7. 1. "REC,Receive Error Counter"
|
|
line.long 0x8 "CAN_NFCR0,Node 0 Frame Counter Register"
|
|
bitfld.long 0x8 23. "CFCOV,CAN Frame Counter Overflow Flag - CFCOV" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x8 22. "CFCIE,CAN Frame Count Interrupt Enable - CFCIE" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x8 19.--20. "CFMOD,CAN Frame Counter Mode - CFMOD" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x8 16.--18. "CFSEL,CAN Frame Count Selection - CFSEL" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x8 0.--15. 1. "CFC,CAN Frame Counter - CFC"
|
|
group.long 0x208++0x7
|
|
line.long 0x0 "CAN_NIPR0,Node 0 Interrupt Pointer Register"
|
|
hexmask.long.byte 0x0 12.--15. 1. "CFCINP,Frame Counter Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 8.--11. 1. "TRINP,Transfer OK Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 4.--7. 1. "LECINP,Last Error Code Interrupt Node Pointer"
|
|
hexmask.long.byte 0x0 0.--3. 1. "ALINP,Alert Interrupt Node Pointer"
|
|
line.long 0x4 "CAN_NPCR0,Node 0 Port Control Register"
|
|
bitfld.long 0x4 8. "LBM,Loop-Back Mode" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x4 0.--2. "RXSEL,Receive Select" "0,1,2,3,4,5,6,7"
|
|
group.long 0x204++0x3
|
|
line.long 0x0 "CAN_NSR0,Node 0 Status Register"
|
|
bitfld.long 0x0 12.--14. "FLEC,Fast Last Error Code" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 11. "RESI,Received Error State Indicator Flag" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 9. "LOE,List Object Error" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "LLE,List Length Error" "0: Const_0,1: Const_1"
|
|
rbitfld.long 0x0 7. "BOFF,Bus-off Status" "0: Const_0,1: Const_1"
|
|
newline
|
|
rbitfld.long 0x0 6. "EWRN,Error Warning Status" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "ALERT,Alert Warning" "0,1"
|
|
bitfld.long 0x0 4. "RXOK,Message Received Successfully" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "TXOK,Message Transmitted Successfully" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0.--2. "LEC,Last Error Code" "0,1,2,3,4,5,6,7"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CLC,CAN Clock Control Register"
|
|
bitfld.long 0x0 3. "EDIS,Sleep Mode Enable Control" "0,1"
|
|
rbitfld.long 0x0 1. "DISS,Module Disable Status Bit" "0,1"
|
|
bitfld.long 0x0 0. "DISR,Module Disable Request Bit" "0,1"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "FDR,CAN Fractional Divider Register"
|
|
bitfld.long 0x0 14.--15. "DM,Divider Mode" "0,1,2,3"
|
|
hexmask.long.word 0x0 0.--9. 1. "STEP,Step Value"
|
|
rgroup.long 0x8++0x3
|
|
line.long 0x0 "ID,Module Identification Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "MOD_NUMBER,Module Number Value"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MOD_TYPE,Module Type"
|
|
hexmask.long.byte 0x0 0.--7. 1. "MOD_REV,Module Revision Number"
|
|
rgroup.long 0x100++0x1F
|
|
line.long 0x0 "LIST0,List Register 0"
|
|
bitfld.long 0x0 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x0 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x0 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x4 "LIST1,List Register 1"
|
|
bitfld.long 0x4 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x4 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x4 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x4 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x8 "LIST2,List Register 2"
|
|
bitfld.long 0x8 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x8 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x8 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x8 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0xC "LIST3,List Register 3"
|
|
bitfld.long 0xC 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0xC 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0xC 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0xC 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x10 "LIST4,List Register 4"
|
|
bitfld.long 0x10 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x10 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x10 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x10 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x14 "LIST5,List Register 5"
|
|
bitfld.long 0x14 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x14 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x14 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x14 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x18 "LIST6,List Register 6"
|
|
bitfld.long 0x18 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x18 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x18 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x18 0.--7. 1. "BEGIN,List Begin"
|
|
line.long 0x1C "LIST7,List Register 7"
|
|
bitfld.long 0x1C 24. "EMPTY,List Empty Indication" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x1C 16.--23. 1. "SIZE,List Size"
|
|
hexmask.long.byte 0x1C 8.--15. 1. "END,List End"
|
|
hexmask.long.byte 0x1C 0.--7. 1. "BEGIN,List Begin"
|
|
group.long 0x1C8++0x3
|
|
line.long 0x0 "MCR,Module Control Register"
|
|
hexmask.long.byte 0x0 12.--15. 1. "MPSEL,Message Pending Selector"
|
|
hexmask.long.byte 0x0 0.--3. 1. "CLKSEL,Baud Rate Logic Clock Select"
|
|
wgroup.long 0x1CC++0x3
|
|
line.long 0x0 "MITR,Module Interrupt Trigger Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "IT,Interrupt Trigger"
|
|
rgroup.long 0x180++0x7
|
|
line.long 0x0 "MSID0,Message Index Register 0"
|
|
hexmask.long.byte 0x0 0.--5. 1. "INDEX,Message Pending Index"
|
|
line.long 0x4 "MSID1,Message Index Register 1"
|
|
hexmask.long.byte 0x4 0.--5. 1. "INDEX,Message Pending Index"
|
|
group.long 0x1C0++0x3
|
|
line.long 0x0 "MSIMASK,Message Index Mask Register"
|
|
hexmask.long 0x0 0.--31. 1. "IM,Message Index Mask"
|
|
group.long 0x140++0x7
|
|
line.long 0x0 "MSPND0,Message Pending Register 0"
|
|
hexmask.long 0x0 0.--31. 1. "PND,Message Pending"
|
|
line.long 0x4 "MSPND1,Message Pending Register 1"
|
|
hexmask.long 0x4 0.--31. 1. "PND,Message Pending"
|
|
group.long 0x1C4++0x3
|
|
line.long 0x0 "PANCTR,Panel Control Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "PANAR2,Panel Argument 2"
|
|
hexmask.long.byte 0x0 16.--23. 1. "PANAR1,Panel Argument 1"
|
|
rbitfld.long 0x0 9. "RBUSY,Result Busy Flag" "0: Const_0,1: Const_1"
|
|
rbitfld.long 0x0 8. "BUSY,Panel Busy Flag" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 0.--7. 1. "PANCMD,Panel Command"
|
|
tree.end
|
|
tree "CANNODEFD"
|
|
base ad:0x48010010
|
|
group.long 0x200++0x3
|
|
line.long 0x0 "CAN_NBTEVR0,Node 0 Bit Timing Extended View Register"
|
|
hexmask.long.byte 0x0 22.--27. 1. "TSEG1,Time Segment Before Sample Point"
|
|
hexmask.long.byte 0x0 16.--20. 1. "TSEG2,Time Segment After Sample Point"
|
|
bitfld.long 0x0 15. "DIV8,Divide Prescaler Clock by 8" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x0 8.--11. 1. "SJW,(Re) Synchronization Jump Width"
|
|
hexmask.long.byte 0x0 0.--5. 1. "BRP,Baud Rate Prescaler"
|
|
group.long 0x228++0x7
|
|
line.long 0x0 "CAN_FNBTR0,Fast Node 0 Bit Timing Register"
|
|
bitfld.long 0x0 12.--14. "FTSEG2,Fast Time Segment After Sample Point" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x0 8.--11. 1. "FTSEG1,Fast Time Segment Before Sample Point"
|
|
bitfld.long 0x0 6.--7. "FSJW,Fast (Re) Synchronization Jump Width" "0,1,2,3"
|
|
hexmask.long.byte 0x0 0.--5. 1. "FBRP,Fast Baud Rate Prescaler"
|
|
line.long 0x4 "CAN_NTDCR0,Node 0 Transmitter Delay Compensation Register"
|
|
bitfld.long 0x4 15. "TDC,Transmitter Delay Compensation Enable" "0: Const_0,1: Const_1"
|
|
hexmask.long.byte 0x4 8.--11. 1. "TDCO,Transmitter Delay Compensation Offset"
|
|
hexmask.long.byte 0x4 0.--5. 1. "TDCV,Transmitter Delay Compensation Value"
|
|
tree.end
|
|
tree.end
|
|
tree "CANTRX (CAN Transceiver)"
|
|
base ad:0x4800C000
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CTRL,CAN transceiver control"
|
|
bitfld.long 0x0 16.--17. "TXD_IN_SEL,TXD input selector" "0: CAN protocol controller TXD,1: UART0 TXD,2: GPT12 T3OUT,3: P0.3"
|
|
bitfld.long 0x0 9. "TSIL_EN,Enable tsilence counter" "0: Tsilence is omitted,1: Tsilence is used for bus bias control"
|
|
newline
|
|
bitfld.long 0x0 8. "EN_TXD_TO,Enable transmitter deactivation due to TXD dominant timeout" "0: TXD dominant timeout disable,1: TXD dominant timeout enable"
|
|
bitfld.long 0x0 1.--2. "MODE,CAN mode control" "0: Sleep mode,1: Receive-only mode,?,3: Normal mode transmit and receive"
|
|
newline
|
|
bitfld.long 0x0 0. "EN,CAN transceiver enable" "0: CAN transceiver disable,1: CAN transceiver enable"
|
|
wgroup.long 0x8++0x3
|
|
line.long 0x0 "IRQCLR,CAN transceiver interrupt status register clear"
|
|
bitfld.long 0x0 18. "OT_SC,CAN overtemperature status clear" "0: Keep status,1: Clear status"
|
|
bitfld.long 0x0 17. "TXD_TO_SC,TXD dominant timeout status clear" "0: Keep status,1: Clear status"
|
|
newline
|
|
bitfld.long 0x0 16. "BUS_TO_SC,Bus dominant timeout status clear" "0: Keep status,1: Clear status"
|
|
bitfld.long 0x0 3. "BUS_ACT_ISC,Bus active during CAN sleep interrupt status clear" "0: Keep interrupt status,1: Clear interrupt status"
|
|
newline
|
|
bitfld.long 0x0 2. "OT_ISC,CAN overtemperature interrupt status clear" "0: Keep interrupt status,1: Clear interrupt status"
|
|
bitfld.long 0x0 1. "TXD_TO_ISC,TXD dominant timeout interrupt status clear" "0: Keep interrupt status,1: Clear interrupt status"
|
|
newline
|
|
bitfld.long 0x0 0. "BUS_TO_ISC,Bus dominant timeout interrupt status clear" "0: Keep interrupt status,1: Clear interrupt status"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "IRQEN,CAN transceiver interrupt enable"
|
|
bitfld.long 0x0 3. "BUS_ACT_IEN,Bus active during CAN sleep interrupt enable" "0: DISABLE,1: ENABLE"
|
|
bitfld.long 0x0 2. "OT_IEN,CAN overtemperature interrupt enable" "0: DISABLE,1: ENABLE"
|
|
newline
|
|
bitfld.long 0x0 1. "TXD_TO_IEN,TXD dominant timeout interrupt enable" "0: DISABLE,1: ENABLE"
|
|
bitfld.long 0x0 0. "BUS_TO_IEN,Bus dominant timeout interrupt enable" "0: DISABLE,1: ENABLE"
|
|
rgroup.long 0x4++0x3
|
|
line.long 0x0 "IRQS,CAN transceiver interrupt status"
|
|
bitfld.long 0x0 20. "UV_STS,CAN supply undervoltage status" "0: CAN supply voltage nominal,1: CAN supply voltage below threshold"
|
|
bitfld.long 0x0 18. "OT_STS,CAN overtemperature status" "0: No overtemperature occurred,1: Overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 17. "TXD_TO_STS,TXD dominant timeout status" "0: No TXD dominant timeout occurred,1: TXD dominant timeout occurred"
|
|
bitfld.long 0x0 16. "BUS_TO_STS,Bus dominant timeout status" "0: No bus dominant timeout occurred,1: Bus dominant timeout occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "BUS_ACT_IS,Bus active during CAN sleep interrupt status" "0: No wake-up interrupt occurred,1: Wake-up interrupt occurred"
|
|
bitfld.long 0x0 2. "OT_IS,CAN overtemperature interrupt status" "0: No OT interrupt occurred,1: OT interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "TXD_TO_IS,TXD dominant timeout interrupt status" "0: No TXD dominant timeout interrupt occurred,1: TXD dominant timeout interrupt occurred"
|
|
bitfld.long 0x0 0. "BUS_TO_IS,Bus dominant timeout interrupt status" "0: No bus dominant timeout interrupt occurred,1: Bus dominant timeout interrupt occurred"
|
|
wgroup.long 0xC++0x3
|
|
line.long 0x0 "IRQSET,CAN transceiver interrupt status register set"
|
|
bitfld.long 0x0 18. "OT_SS,CAN overtemperature status set" "0: Keep status,1: Set status"
|
|
bitfld.long 0x0 17. "TXD_TO_SS,TXD dominant timeout status set" "0: Keep status,1: Set status"
|
|
newline
|
|
bitfld.long 0x0 16. "BUS_TO_SS,Bus dominant timeout status set" "0: Keep status,1: Set status"
|
|
bitfld.long 0x0 3. "BUS_ACT_ISS,Bus active during CAN sleep interrupt status set" "0: Keep interrupt status,1: Set interrupt status"
|
|
newline
|
|
bitfld.long 0x0 2. "OT_ISS,CAN overtemperature interrupt status set" "0: Keep interrupt status,1: Set interrupt status"
|
|
bitfld.long 0x0 1. "TXD_TO_ISS,TXD dominant timeout interrupt status set" "0: Keep interrupt status,1: Set interrupt status"
|
|
newline
|
|
bitfld.long 0x0 0. "BUS_TO_ISS,Bus dominant timeout interrupt status set" "0: Keep interrupt status,1: Set interrupt status"
|
|
tree.end
|
|
tree "CCU7 (Capture/Compare Unit 7)"
|
|
base ad:0x40008000
|
|
rgroup.long 0x90++0x3
|
|
line.long 0x0 "C73R,Compare Register for Channel C73"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Channel C7x Compare Value - CCV"
|
|
group.long 0xA0++0x3
|
|
line.long 0x0 "C73SR,Compare Shadow Reg. for Channel CC73"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel CC73 Compare Value"
|
|
rgroup.long 0x94++0x3
|
|
line.long 0x0 "C74R,Compare Register for Channel C74"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Channel C7x Compare Value - CCV"
|
|
group.long 0xA4++0x3
|
|
line.long 0x0 "C74SR,Compare Shadow Reg. for Channel CC74"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel CC74 Compare Value"
|
|
rgroup.long 0x98++0x3
|
|
line.long 0x0 "C75R,Compare Register for Channel C75"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Channel C7x Compare Value - CCV"
|
|
group.long 0xA8++0x3
|
|
line.long 0x0 "C75SR,Compare Shadow Reg. for Channel CC75"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel CC75 Compare Value"
|
|
rgroup.long 0x9C++0x3
|
|
line.long 0x0 "C76R,Compare Register for Channel C76"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Channel C7x Compare Value - CCV"
|
|
group.long 0xAC++0x3
|
|
line.long 0x0 "C76SR,Compare Shadow Reg. for Channel CC76"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel CC76 Compare Value"
|
|
rgroup.long 0x58++0x3
|
|
line.long 0x0 "CC70BR,Compare Register for Channel C70B"
|
|
hexmask.long.word 0x0 0.--15. 1. "CV,Compare Value - CV"
|
|
group.long 0x64++0x3
|
|
line.long 0x0 "CC70BSR,Compare Shadow Reg. for Channel C70BSR"
|
|
hexmask.long.word 0x0 0.--15. 1. "CS,Shadow Register for Channel x Compare Value - CS"
|
|
rgroup.long 0x40++0x3
|
|
line.long 0x0 "CC70R,Capture/Compare Register for Channel CC70"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Capture/Compare Value - CCV"
|
|
group.long 0x4C++0x3
|
|
line.long 0x0 "CC70SR,Capture/Compare Shadow Reg. for Channel CC70"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel x Capture/Compare Value - CCS"
|
|
rgroup.long 0x5C++0x3
|
|
line.long 0x0 "CC71BR,Compare Register for Channel C71B"
|
|
hexmask.long.word 0x0 0.--15. 1. "CV,Compare Value - CV"
|
|
group.long 0x68++0x3
|
|
line.long 0x0 "CC71BSR,Compare Shadow Reg. for Channel C71BSR"
|
|
hexmask.long.word 0x0 0.--15. 1. "CS,Shadow Register for Channel x Compare Value - CS"
|
|
rgroup.long 0x44++0x3
|
|
line.long 0x0 "CC71R,Capture/Compare Register for Channel CC71"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Capture/Compare Value - CCV"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "CC71SR,Capture/Compare Shadow Reg. for Channel CC71"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel x Capture/Compare Value - CCS"
|
|
rgroup.long 0x60++0x3
|
|
line.long 0x0 "CC72BR,Compare Register for Channel C72B"
|
|
hexmask.long.word 0x0 0.--15. 1. "CV,Compare Value - CV"
|
|
group.long 0x6C++0x3
|
|
line.long 0x0 "CC72BSR,Compare Shadow Reg. for Channel C72BSR"
|
|
hexmask.long.word 0x0 0.--15. 1. "CS,Shadow Register for Channel x Compare Value - CS"
|
|
rgroup.long 0x48++0x3
|
|
line.long 0x0 "CC72R,Capture/Compare Register for Channel CC72"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCV,Capture/Compare Value - CCV"
|
|
group.long 0x54++0x3
|
|
line.long 0x0 "CC72SR,Capture/Compare Shadow Reg. for Channel CC72"
|
|
hexmask.long.word 0x0 0.--15. 1. "CCS,Shadow Register for Channel x Capture/Compare Value - CCS"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CLC,Clock Control Register"
|
|
rbitfld.long 0x0 1. "DISS,Module Disable Status Bit - DISS" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 0. "DISR,Module Disable Request Bit - DISR" "0: Const_0,1: Const_1"
|
|
wgroup.long 0xB8++0x3
|
|
line.long 0x0 "CMPMODIF,Compare State Modification Register"
|
|
bitfld.long 0x0 14. "MCC73R,Capture/Compare Status Modification Bits (Reset)" "0: Bit CC73ST is not changed.,1: Bit CC73ST is set."
|
|
bitfld.long 0x0 13. "MCC72BR,Compare B Status Modification Bit 2(Reset)" "0: Bit CC70ST is not changed.,1: Bit CC70ST is set."
|
|
newline
|
|
bitfld.long 0x0 12. "MCC71BR,Compare B Status Modification Bit 1(Reset)" "0: Bit CC70ST is not changed.,1: Bit CC70ST is set."
|
|
bitfld.long 0x0 11. "MCC70BR,Compare B Status Modification Bit 0(Reset)" "0: Bit CC70ST is not changed.,1: Bit CC70ST is set."
|
|
newline
|
|
bitfld.long 0x0 10. "MCC72R,Capture/Compare Status Modification Bit 2(Reset)" "0: Bit CC72ST is not changed.,1: Bit CC72ST is set."
|
|
bitfld.long 0x0 9. "MCC71R,Capture/Compare Status Modification Bit 1(Reset)" "0: Bit CC71ST is not changed.,1: Bit CC71ST is set."
|
|
newline
|
|
bitfld.long 0x0 8. "MCC70R,Capture/Compare Status Modification Bit 0(Reset)" "0: Bit CC70ST is not changed.,1: Bit CC70ST is set."
|
|
bitfld.long 0x0 6. "MCC73S,Capture/Compare Status Modification Bits (Set)" "0: Bit CC73ST is not changed.,1: Bit CC73ST is set."
|
|
newline
|
|
bitfld.long 0x0 5. "MCC72BS,Compare B Status Modification Bit 2 (Set)" "0,1"
|
|
bitfld.long 0x0 4. "MCC71BS,Compare B Status Modification Bit 1 (Set)" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "MCC70BS,Compare B Status Modification Bit 0 (Set)" "0,1"
|
|
bitfld.long 0x0 2. "MCC72S,Capture/Compare Status Modification Bit 2 (Set)" "0,1"
|
|
newline
|
|
bitfld.long 0x0 1. "MCC71S,Capture/Compare Status Modification Bit 1 (Set)" "0,1"
|
|
bitfld.long 0x0 0. "MCC70S,Capture/Compare Status Modification Bit 0 (Set)" "0,1"
|
|
group.long 0xBC++0x3
|
|
line.long 0x0 "CMPMODIF_2,Compare State Modification Register 2"
|
|
bitfld.long 0x0 14. "C72BINV,Output channel C72BST Inversion Enable" "0: Output Channel C72BST not inverted,1: Output Channel C72BST inverted"
|
|
bitfld.long 0x0 13. "C71BINV,Output channel C71BST Inversion Enable" "0: Output Channel C71BST not inverted,1: Output Channel C71BST inverted"
|
|
newline
|
|
bitfld.long 0x0 12. "C70BINV,Output channel C70BST Inversion Enable" "0: Output Channel C70BST not inverted,1: Output Channel C70BST inverted"
|
|
bitfld.long 0x0 10. "MC76R,Compare Status Modification Bit 6(Reset)" "0: Bit CC76ST is not changed.,1: Bit CC76ST is set"
|
|
newline
|
|
bitfld.long 0x0 9. "MC75R,Compare Status Modification Bit 5(Reset)" "0: Bit CC75ST is not changed.,1: Bit CC76ST is set."
|
|
bitfld.long 0x0 8. "MC74R,Compare Status Modification Bit 4(Reset)" "0: Bit CC74ST is not changed.,1: Bit CC74ST is set."
|
|
newline
|
|
bitfld.long 0x0 6. "CC72INV,Output channel CC72ST Inversion Enable" "0: Output Channel CC72ST not inverted,1: Output Channel CC72ST inverted"
|
|
bitfld.long 0x0 5. "CC71INV,Output channel CC71ST Inversion Enable" "0: Output Channel CC71ST not inverted,1: Output Channel CC71ST inverted"
|
|
newline
|
|
bitfld.long 0x0 4. "CC70INV,Output channel CC70ST Inversion Enable" "0: Output Channel CC70ST not inverted,1: Output Channel CC70ST inverted"
|
|
bitfld.long 0x0 2. "MC76S,Compare Status Modification Bit 6 (Set)" "0: Bit CC76ST is not changed.,1: Bit CC76ST is set."
|
|
newline
|
|
bitfld.long 0x0 1. "MC75S,Compare Status Modification Bit 5 (Set)" "0: Bit CC75ST is not changed.,1: Bit CC75ST is set."
|
|
bitfld.long 0x0 0. "MC74S,Compare Status Modification Bit 4 (Set)" "0: Bit CC74ST is not changed.,1: Bit CC74ST is set."
|
|
group.long 0xB0++0x3
|
|
line.long 0x0 "CMPSTAT,Compare State Register"
|
|
bitfld.long 0x0 15. "T13IM,T13 Inverted Modulation" "0: T13 output is not inverted.,1: T13 output is inverted for further modulation."
|
|
bitfld.long 0x0 14. "COUT73PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
newline
|
|
bitfld.long 0x0 13. "COUT72PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
bitfld.long 0x0 12. "CC72PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
newline
|
|
bitfld.long 0x0 11. "COUT71PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
bitfld.long 0x0 10. "CC71PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
newline
|
|
bitfld.long 0x0 9. "COUT70PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
bitfld.long 0x0 8. "CC70PS,Passive State Select for Compare Outputs" "0: The corresponding compare output drives passive..,1: The corresponding compare output drives passive.."
|
|
newline
|
|
rbitfld.long 0x0 6. "CC73ST,Compare State Bits" "0: The counter value is less than the compare value.,1: The counter value is greater than or equal to.."
|
|
rbitfld.long 0x0 5. "CCPOS2,Sampled Hall Pattern Bit 2" "0: The input CCPOS2 has been sampled as 0.,1: The input CCPOS2 has been sampled as 1."
|
|
newline
|
|
rbitfld.long 0x0 4. "CCPOS1,Sampled Hall Pattern Bit 1" "0: The input CCPOS1 has been sampled as 0.,1: The input CCPOS1 has been sampled as 1."
|
|
rbitfld.long 0x0 3. "CCPOS0,Sampled Hall Pattern Bit 0" "0: The input CCPOS0 has been sampled as 0.,1: The input CCPOS0 has been sampled as 1."
|
|
newline
|
|
rbitfld.long 0x0 2. "CC72ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
rbitfld.long 0x0 1. "CC71ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
newline
|
|
rbitfld.long 0x0 0. "CC70ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
rgroup.long 0xB4++0x3
|
|
line.long 0x0 "CMPSTAT_2,Compare State Register 2"
|
|
bitfld.long 0x0 10. "CC72ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
bitfld.long 0x0 9. "CC71ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
newline
|
|
bitfld.long 0x0 8. "CC70ST,Capture/Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
bitfld.long 0x0 6. "C76ST,Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
newline
|
|
bitfld.long 0x0 5. "C75ST,Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
bitfld.long 0x0 4. "C74ST,Compare State Bits" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
newline
|
|
bitfld.long 0x0 2. "C72BST,Compare State Bits B" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
bitfld.long 0x0 1. "C71BST,Compare State Bits B" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
newline
|
|
bitfld.long 0x0 0. "C70BST,Compare State Bits B" "0: In compare mode the timer count is less than the..,1: In compare mode the counter value is greater.."
|
|
rgroup.long 0x8++0x3
|
|
line.long 0x0 "ID,Module Identification Register"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MODNUM,Module Number Value - MODNUM"
|
|
hexmask.long.byte 0x0 0.--7. 1. "MODREV,Module Revision Number - MODREV"
|
|
group.long 0x11C++0x3
|
|
line.long 0x0 "IEN,Capture/Compare Interrupt Enable Register 1"
|
|
bitfld.long 0x0 15. "ENSTR,Enable Multi-Channel Mode Shadow Transfer Interrupt" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 14. "ENIDLE,Enable Idle" "0: The bit IDLE is not automatically set when a..,1: The bit IDLE is automatically set when a wrong.."
|
|
newline
|
|
bitfld.long 0x0 13. "ENWHE,Enable Interrupt for Wrong Hall Event" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 12. "ENCHE,Enable Interrupt for Correct Hall Event" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 10. "ENTRPF,Enable Interrupt for Trap Flag" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 9. "ENT13PM,Enable Interrupt for T13 Period-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 8. "ENT13CM,Enable Interrupt for T13 Compare-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 7. "ENT12PM,Enable Interrupt for T12 Period-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 6. "ENT12OM,Enable Interrupt for T12 One-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 5. "ENCC72F,Capture Compare-Match Falling Edge Interrupt Enable for Channel 2" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 4. "ENCC72R,Capture Compare-Match Rising Edge Interrupt Enable for Channel 2" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 3. "ENCC71F,Capture Compare-Match Falling Edge Interrupt Enable for Channel 1" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 2. "ENCC71R,Capture Compare-Match Rising Edge Interrupt Enable for Channel 1" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 1. "ENCC70F,Capture Compare-Match Falling Edge Interrupt Enable for Channel 0" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 0. "ENCC70R,Capture Compare-Match Rising Edge Interrupt Enable for Channel 0" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
group.long 0x130++0x3
|
|
line.long 0x0 "IEN_2,Capture/Compare Interrupt Enable Register 2"
|
|
bitfld.long 0x0 13. "ENT16PM,Enable Interrupt for T16 Period-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 12. "ENT16CM,Enable Interrupt for T16 Compare-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 11. "ENT15PM,Enable Interrupt for T15 Period-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 10. "ENT15CM,Enable Interrupt for T15 Compare-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 9. "ENT14PM,Enable Interrupt for T14 Period-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 8. "ENT14CM,Enable Interrupt for T14 Compare-Match" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 5. "ENCC72BF,Capture Compare-Match Falling Edge Interrupt Enable for Channel 2" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 4. "ENCC72BR,Capture Compare-Match Rising Edge Interrupt Enable for Channel 2" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 3. "ENCC71BF,Capture Compare-Match Falling Edge Interrupt Enable for Channel 1" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 2. "ENCC71BR,Capture Compare-Match Rising Edge Interrupt Enable for Channel 1" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
newline
|
|
bitfld.long 0x0 1. "ENCC70BF,Capture Compare-Match Falling Edge Interrupt Enable for Channel 0" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
bitfld.long 0x0 0. "ENCC70BR,Capture Compare-Match Rising Edge Interrupt Enable for Channel 0" "0: No interrupt will be generated if the set..,1: An interrupt will be generated if the set.."
|
|
group.long 0x148++0x3
|
|
line.long 0x0 "IGT,Interupt gating Register"
|
|
bitfld.long 0x0 12.--13. "GT3,Gating SR3" "0: No gating,1: Gated off with T12 CDIR = 0,2: Gated off with T12 CDIR = 1,3: Gated off with Input SR_GT3 = 0"
|
|
bitfld.long 0x0 8.--9. "GT2,Gating SR2" "0: No gating,1: Gated off with T12 CDIR = 0,2: Gated off with T12 CDIR = 1,3: Gated off with Input SR_GT2 = 0"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "GT1,Gating SR1" "0: No gating,1: Gated off with T12 CDIR = 0,2: Gated off with T12 CDIR = 1,3: Gated off with Input SR_GT1 = 0"
|
|
bitfld.long 0x0 0.--1. "GT0,Gating SR0" "0: No gating,1: Gated off with T12 CDIR = 0,2: Gated off with T12 CDIR = 1,3: Gated off with Input SR_GT0 = 0"
|
|
group.long 0x104++0x3
|
|
line.long 0x0 "IMON,Input Monitoring Register"
|
|
bitfld.long 0x0 9. "T13HRI,Event indication for input signal T13HR - T13HRI" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "T12HRI,Event indication for input signal T12HR - T12HRI" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 7. "CTRAPI,Event indication for input signal CTRAP - CTRAPI" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "CC72INI,Event indication for input signal CC72IN - CC72INI" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 5. "CC71INI,Event indication for input signal CC71IN - CC71INI" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 4. "CC70INI,Event indication for input signal CC70IN - CC70INI" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 3. "CCPOS2I,Event indication for input signal CCPOS2 - CCPOS2I" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "CCPOS1I,Event indication for input signal CCPOS1 - CCPOS1I" "0: Const_0,1: CCPOS1I"
|
|
newline
|
|
bitfld.long 0x0 1. "CCPOS0I,Event indication for input signal CCPOS0 - CCPOS0I" "0: CCPOS0I,1: Const_1"
|
|
bitfld.long 0x0 0. "LBE,Lost Bit Event - LBE" "0: Const_0,1: Const_1"
|
|
group.long 0x118++0x3
|
|
line.long 0x0 "INP,Capture/Compare Interrupt Node Pointer Register 1"
|
|
bitfld.long 0x0 12.--13. "INPT13,Interrupt Node Pointer for Timer T13 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 10.--11. "INPT12,Interrupt Node Pointer for Timer T12 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
newline
|
|
bitfld.long 0x0 8.--9. "INPERR,Interrupt Node Pointer for Error Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 6.--7. "INPCHE,Interrupt Node Pointer for the CHE Interrupt" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
newline
|
|
bitfld.long 0x0 4.--5. "INPCC72,Interrupt Node Pointer for Channel 2 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 2.--3. "INPCC71,Interrupt Node Pointer for Channel 1 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
newline
|
|
bitfld.long 0x0 0.--1. "INPCC70,Interrupt Node Pointer for Channel 0 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
group.long 0x12C++0x3
|
|
line.long 0x0 "INP_2,Capture/Compare Interrupt Node Pointer Register 2"
|
|
bitfld.long 0x0 12.--13. "INPT16,Interrupt Node Pointer for Timer T16 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 10.--11. "INPT15,Interrupt Node Pointer for Timer T15 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
newline
|
|
bitfld.long 0x0 8.--9. "INPT14,Interrupt Node Pointer for Timer T14 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 4.--5. "INPCC72B,Interrupt Node Pointer for Channel 2 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
newline
|
|
bitfld.long 0x0 2.--3. "INPCC71B,Interrupt Node Pointer for Channel 1 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
bitfld.long 0x0 0.--1. "INPCC70B,Interrupt Node Pointer for Channel 0 Interrupts" "0: Interrupt output line SR0 is selected.,1: Interrupt output line SR1 is selected.,2: Interrupt output line SR2 is selected.,3: Interrupt output line SR3 is selected."
|
|
rgroup.long 0x10C++0x3
|
|
line.long 0x0 "IS,Capture/Compare Interrupt Status Register 1"
|
|
bitfld.long 0x0 15. "STR,Multi-Channel Mode Shadow Transfer Request" "0: The shadow transfer has not yet taken place.,1: The shadow transfer has taken place."
|
|
bitfld.long 0x0 14. "IDLE,IDLE State" "0: Noaction,1: Bit field MCMP is cleared and held to 0 the.."
|
|
newline
|
|
bitfld.long 0x0 13. "WHE,Wrong Hall Event" "0: A transition to a wrong hall event (not the..,1: A transition to a wrong hall event (not the.."
|
|
bitfld.long 0x0 12. "CHE,Correct Hall Event" "0: A transition to a correct (= expected) hall..,1: A transition to a correct (= expected) hall.."
|
|
newline
|
|
bitfld.long 0x0 11. "TRPS,Trap State" "0: The trap state is not active.,1: The trap state is active. Bit TRPS is set while.."
|
|
bitfld.long 0x0 10. "TRPF,Trap Flag" "0: The trap condition has not been detected.,1: The trap condition has been detected (input"
|
|
newline
|
|
bitfld.long 0x0 9. "T13PM,Timer T13 Period-Match Flag" "0: A timer T13 period-match has not yet been..,1: A timer T13 period-match has been detected."
|
|
bitfld.long 0x0 8. "T13CM,Timer T13 Compare-Match Flag" "0: A timer T13 compare-match has not yet been..,1: A timer T13 compare-match has been detected."
|
|
newline
|
|
bitfld.long 0x0 7. "T12PM,Timer T12 Period-Match Flag" "0: A timer T12 period-match (while counting up) has..,1: A timer T12 period-match (while counting up) has.."
|
|
bitfld.long 0x0 6. "T12OM,Timer T12 One-Match Flag" "0: A timer T12 one-match (while counting down) has..,1: A timer T12 one-match (while counting down) has.."
|
|
newline
|
|
bitfld.long 0x0 5. "ICC72F,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 4. "ICC72R,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
newline
|
|
bitfld.long 0x0 3. "ICC71F,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 2. "ICC71R,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
newline
|
|
bitfld.long 0x0 1. "ICC70F,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 0. "ICC70R,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
wgroup.long 0x114++0x3
|
|
line.long 0x0 "ISR,Capture/Compare Interrupt Status Reset Register 1"
|
|
bitfld.long 0x0 15. "RSTR,Reset STR Flag" "0: Noaction,1: Bit STR in register IS will be cleared."
|
|
bitfld.long 0x0 14. "RIDLE,Reset IDLE Flag" "0: Noaction,1: Bit IDLE in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 13. "RWHE,Reset Wrong Hall Event Flag" "0: Noaction,1: Bit WHE in register IS will be cleared."
|
|
bitfld.long 0x0 12. "RCHE,Reset Correct Hall Event Flag" "0: Noaction,1: Bit CHE in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 10. "RTRPF,Reset Trap Flag" "0: Noaction,1: Bit TRPF in register IS will be cleared (not.."
|
|
bitfld.long 0x0 9. "RT13PM,Reset Timer T13 Period-Match Flag" "0: Noaction,1: Bit T13PM in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 8. "RT13CM,Reset Timer T13 Compare-Match Flag" "0: Noaction,1: Bit T13CM in register IS will be cleared."
|
|
bitfld.long 0x0 7. "RT12PM,Reset Timer T12 Period-Match Flag" "0: Noaction,1: Bit T12PM in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 6. "RT12OM,Reset Timer T12 One-Match Flag" "0: Noaction,1: Bit T12OM in register IS will be cleared."
|
|
bitfld.long 0x0 5. "RCC72F,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC72F in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 4. "RCC72R,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC72R in register IS will be cleared."
|
|
bitfld.long 0x0 3. "RCC71F,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC71F in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 2. "RCC71R,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC71R in register IS will be cleared."
|
|
bitfld.long 0x0 1. "RCC70F,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC70F in register IS will be cleared."
|
|
newline
|
|
bitfld.long 0x0 0. "RCC70R,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC70R in register IS will be cleared."
|
|
wgroup.long 0x128++0x3
|
|
line.long 0x0 "ISR_2,Capture/Compare Interrupt Status Reset Register 2"
|
|
bitfld.long 0x0 13. "RT16PM,Reset Timer T16 Period-Match Flag" "0: Noaction,1: Bit T16PM in register IS_2 will be cleared."
|
|
bitfld.long 0x0 12. "RT16CM,Reset Timer T16 Compare-Match Flag" "0: Noaction,1: Bit T16CM in register IS_2 will be cleared."
|
|
newline
|
|
bitfld.long 0x0 11. "RT15PM,Reset Timer T15 Period-Match Flag" "0: Noaction,1: Bit T15PM in register IS_2 will be cleared."
|
|
bitfld.long 0x0 10. "RT15CM,Reset Timer T15 Compare-Match Flag" "0: Noaction,1: Bit T15CM in register IS_2 will be cleared."
|
|
newline
|
|
bitfld.long 0x0 9. "RT14PM,Reset Timer T14 Period-Match Flag" "0: Noaction,1: Bit T14PM in register IS_2 will be cleared."
|
|
bitfld.long 0x0 8. "RT14CM,Reset Timer T14 Compare-Match Flag" "0: Noaction,1: Bit T14CM in register IS_2 will be cleared."
|
|
newline
|
|
bitfld.long 0x0 5. "RCC72BF,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC72BF in register IS_2 will be cleared."
|
|
bitfld.long 0x0 4. "RCC72BR,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC72BR in register IS_2 will be cleared."
|
|
newline
|
|
bitfld.long 0x0 3. "RCC71BF,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC71BF in register IS_2 will be cleared."
|
|
bitfld.long 0x0 2. "RCC71BR,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC71BR in register IS_2 will be cleared."
|
|
newline
|
|
bitfld.long 0x0 1. "RCC70BF,Reset Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC70BF in register IS_2 will be cleared."
|
|
bitfld.long 0x0 0. "RCC70BR,Reset Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC70BR in register IS_2 will be cleared."
|
|
wgroup.long 0x110++0x3
|
|
line.long 0x0 "ISS,Capture/Compare Interrupt Status Set Register 1"
|
|
bitfld.long 0x0 15. "SSTR,Set STR Flag" "0: Noaction,1: Bit STR in register IS will be set."
|
|
bitfld.long 0x0 14. "SIDLE,Set IDLE Flag" "0: Noaction,1: Bit IDLE in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 13. "SWHE,Set Wrong Hall Event Flag" "0: Noaction,1: Bit WHE in register IS will be set."
|
|
bitfld.long 0x0 12. "SCHE,Set Correct Hall Event Flag" "0: Noaction,1: Bit CHE in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 11. "SWHC,Software Hall Compare" "0: Noaction,1: The Hall compare action is triggered."
|
|
bitfld.long 0x0 10. "STRPF,Set Trap Flag" "0: Noaction,1: Bits TRPF and TRPS in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 9. "ST13PM,Set Timer T13 Period-Match Flag" "0: Noaction,1: Bit T13PM in register IS will be set."
|
|
bitfld.long 0x0 8. "ST13CM,Set Timer T13 Compare-Match Flag" "0: Noaction,1: Bit T13CM in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 7. "ST12PM,Set Timer T12 Period-Match Flag" "0: Noaction,1: Bit T12PM in register IS will be set."
|
|
bitfld.long 0x0 6. "ST12OM,Set Timer T12 One-Match Flag" "0: Noaction,1: Bit T12OM in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 5. "SCC72F,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC72F in register IS will be set."
|
|
bitfld.long 0x0 4. "SCC72R,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC72R in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 3. "SCC71F,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC71F in register IS will be set."
|
|
bitfld.long 0x0 2. "SCC71R,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC71R in register IS will be set."
|
|
newline
|
|
bitfld.long 0x0 1. "SCC70F,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC70F in register IS will be set."
|
|
bitfld.long 0x0 0. "SCC70R,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC70R in register IS will be set."
|
|
wgroup.long 0x124++0x3
|
|
line.long 0x0 "ISS_2,Capture/Compare Interrupt Status Set Register 2"
|
|
bitfld.long 0x0 13. "ST16PM,Set Timer T16 Period-Match Flag" "0: Noaction,1: Bit T16PM in register IS_2 will be set."
|
|
bitfld.long 0x0 12. "ST16CM,Set Timer T16 Compare-Match Flag" "0: Noaction,1: Bit T16CM in register IS_2 will be set."
|
|
newline
|
|
bitfld.long 0x0 11. "ST15PM,Set Timer T15 Period-Match Flag" "0: Noaction,1: Bit T15PM in register IS_2 will be set."
|
|
bitfld.long 0x0 10. "ST15CM,Set Timer T15 Compare-Match Flag" "0: Noaction,1: Bit T15CM in register IS_2 will be set."
|
|
newline
|
|
bitfld.long 0x0 9. "ST14PM,Set Timer T14 Period-Match Flag" "0: Noaction,1: Bit T14PM in register IS_2 will be set."
|
|
bitfld.long 0x0 8. "ST14CM,Set Timer T14 Compare-Match Flag" "0: Noaction,1: Bit T14CM in register IS_2 will be set."
|
|
newline
|
|
bitfld.long 0x0 5. "SCC72BF,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC72BF in register IS_2 will be set."
|
|
bitfld.long 0x0 4. "SCC72BR,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC72BR in register IS_2 will be set."
|
|
newline
|
|
bitfld.long 0x0 3. "SCC71BF,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC71BF in register IS_2 will be set."
|
|
bitfld.long 0x0 2. "SCC71BR,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC71BR in register IS_2 will be set."
|
|
newline
|
|
bitfld.long 0x0 1. "SCC70BF,Set Capture Compare-Match Falling Edge Flag" "0: Noaction,1: Bit CC70BF in register IS_2 will be set."
|
|
bitfld.long 0x0 0. "SCC70BR,Set Capture Compare-Match Rising Edge Flag" "0: Noaction,1: Bit CC70BR in register IS_2 will be set."
|
|
rgroup.long 0x120++0x3
|
|
line.long 0x0 "IS_2,Capture/Compare Interrupt Status Register 2"
|
|
bitfld.long 0x0 13. "T16PM,Timer T16 Period-Match Flag" "0: A timer T16 period-match has not yet been..,1: A timer T16 period-match has been detected."
|
|
bitfld.long 0x0 12. "T16CM,Timer T16 Compare-Match Flag" "0: A timer T16 compare-match has not yet been..,1: A timer T16 compare-match has been detected."
|
|
newline
|
|
bitfld.long 0x0 11. "T15PM,Timer T15 Period-Match Flag" "0: A timer T15 period-match has not yet been..,1: A timer T15 period-match has been detected."
|
|
bitfld.long 0x0 10. "T15CM,Timer T15 Compare-Match Flag" "0: A timer T15 compare-match has not yet been..,1: A timer T15 compare-match has been detected."
|
|
newline
|
|
bitfld.long 0x0 9. "T14PM,Timer T14 Period-Match Flag" "0: A timer T14 period-match has not yet been..,1: A timer T14 period-match has been detected."
|
|
bitfld.long 0x0 8. "T14CM,Timer T14 Compare-Match Flag" "0: A timer T14 compare-match has not yet been..,1: A timer T14 compare-match has been detected."
|
|
newline
|
|
bitfld.long 0x0 5. "ICC72BF,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 4. "ICC72BR,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
newline
|
|
bitfld.long 0x0 3. "ICC71BF,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 2. "ICC71BR,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
newline
|
|
bitfld.long 0x0 1. "ICC70BF,Capture Compare-Match Falling Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
bitfld.long 0x0 0. "ICC70BR,Capture Compare-Match Rising Edge Flag" "0: The event has not yet occurred since this bit..,1: The event described above has been detected."
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "KSCSR,Kernel State Control Sensitivity Register"
|
|
bitfld.long 0x0 6. "SB6,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 5. "SB5,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 4. "SB4,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 3. "SB3,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 2. "SB2,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "SB1,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 0. "SB0,Sensitivity Block x SBx (x=0 1 2 ...)" "0: Const_0,1: Const_1"
|
|
group.long 0x108++0x3
|
|
line.long 0x0 "LI,Lost Indicator Register"
|
|
bitfld.long 0x0 14.--15. "INPLBE,Interrupt Node Pointer for lost bit event - INPLBE" "0: Const_0,1: Const_1,2: Const_2,3: Const_3"
|
|
bitfld.long 0x0 13. "LBEEN,Interrupt Enable for Lost Bit Event - LBEEN" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 9. "T13HREN,Lost Indicator Enable for input signal T13HR - T13HREN" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 8. "T12HREN,Lost Indicator Enable for input signal T12HR - T12HREN" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 7. "CTRAPEN,Lost Indicator Enable for input signal CTRAP - CTRAPEN" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "CC72INEN,Lost Indicator Enable for input signal CC72IN - CC72INEN" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 5. "CC71INEN,Lost Indicator Enable for input signal CC71IN - CC71INEN" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 4. "CC70INEN,Lost Indicator Enable for input signal CC70IN - CC70INEN" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 3. "CCPOS2EN,Lost Indicator Enable for input signal CCPOS2 - CCPOS2EN" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 2. "CCPOS1EN,Lost Indicator Enable for input signal CCPOS1 - CCPOS1EN" "0: Const_0,1: CCPOS1EN"
|
|
newline
|
|
bitfld.long 0x0 1. "CCPOS0EN,Lost Indicator Enable for input signal CCPOS0 - CCPOS0EN" "0: CCPOS0EN,1: Const_1"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "MCFG,Module Configuration Register"
|
|
bitfld.long 0x0 15. "WREN,Write Enable - WREN" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 6. "T16,T16 Available - T16" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 5. "T15,T15 Available - T15" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 4. "T14,T14 Available -T14" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 2. "MCM,Multi-Channel Mode Available - MCM" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 1. "T13,T13 Available - T13" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 0. "T12,T12 Available - T12" "0: Const_0,1: Const_1"
|
|
group.long 0x100++0x3
|
|
line.long 0x0 "MCMCTR,Multi-Channel Mode Control Register"
|
|
bitfld.long 0x0 10. "STE13U,Shadow Transfer Enable for T13 Upcounting" "0: Noaction,1: The T13_ST shadow transfer mechanism is enabled.."
|
|
bitfld.long 0x0 9. "STE12D,Shadow Transfer Enable for T12 Downcounting" "0: Noaction,1: The T12_ST shadow transfer mechanism is enabled.."
|
|
newline
|
|
bitfld.long 0x0 8. "STE12U,Shadow Transfer Enable for T12 Upcounting" "0: Noaction,1: The T12_ST shadow transfer mechanism is enabled.."
|
|
bitfld.long 0x0 4.--5. "SWSYN,Switching Synchronization" "0: the trigger event directly causes the shadow..,1: T13 zero-match triggers the shadow transfer,2: a T12 zero-match (while counting up) triggers..,?"
|
|
newline
|
|
bitfld.long 0x0 0.--2. "SWSEL,Switching Selection" "0: no trigger request will be generated,1: correct hall pattern on CCPOSx detected,2: T13 period-match detected (while counting up),3: T12 one-match (while counting down),4: T12 channel 1 compare-match detected (phase..,5: T12 period match detected (while counting up)..,?,?"
|
|
rgroup.long 0xFC++0x3
|
|
line.long 0x0 "MCMOUT,Multi-Channel Mode Output Register"
|
|
bitfld.long 0x0 11.--13. "CURH,Current Hall Pattern - CURH" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 8.--10. "EXPH,Expected Hall Pattern - EXPH" "0,1,2,3,4,5,6,7"
|
|
newline
|
|
bitfld.long 0x0 6. "R,Reminder Flag" "0: Currently no shadow transfer from MCMPS to MCMP..,1: A shadow transfer from MCMPS to MCMP has been.."
|
|
hexmask.long.byte 0x0 0.--5. 1. "MCMP,Multi-Channel PWM Pattern"
|
|
group.long 0xF8++0x3
|
|
line.long 0x0 "MCMOUTS,Multi-Channel Mode Output Shadow Register"
|
|
bitfld.long 0x0 15. "STRHP,Shadow Transfer Request for the Hall Pattern - STRHP" "0: NoAction,1: Update"
|
|
bitfld.long 0x0 11.--13. "CURHS,Current Hall Pattern Shadow" "0,1,2,3,4,5,6,7"
|
|
newline
|
|
bitfld.long 0x0 8.--10. "EXPHS,Expected Hall Pattern Shadow" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 7. "STRMCM,Shadow Transfer Request for MCMPS - STRMCM" "0: NoAction,1: Update"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "MCMPS,Multi-Channel PWM Pattern Shadow"
|
|
group.long 0xEC++0x3
|
|
line.long 0x0 "MODCTR,Modulation Control Register"
|
|
bitfld.long 0x0 15. "ECT13O,Enable Compare Timer T13 Output" "0: The alternate output function COUT73 is disabled.,1: The alternate output function COUT73 is enabled.."
|
|
bitfld.long 0x0 13. "T13MODEN_COUT72,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 12. "T13MODEN_CC72,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 11. "T13MODEN_COUT71,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 10. "T13MODEN_CC71,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 9. "T13MODEN_COUT70,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 8. "T13MODEN_CC70,T13 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 7. "MCMEN,Multi-Channel Mode Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 5. "T12MODEN_COUT72,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 4. "T12MODEN_CC72,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 3. "T12MODEN_COUT71,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 2. "T12MODEN_CC71,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
newline
|
|
bitfld.long 0x0 1. "T12MODEN_COUT70,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
bitfld.long 0x0 0. "T12MODEN_CC70,T12 Modulation Enable" "0: The modulation of the corresponding output..,1: The modulation of the corresponding output.."
|
|
group.long 0x134++0x3
|
|
line.long 0x0 "OCS,OCDS Control and Status Register"
|
|
rbitfld.long 0x0 29. "SUSSTA,Suspend State - SUSSTA" "0: Const_0,1: Const_1"
|
|
bitfld.long 0x0 28. "SUS_P,SUS Write Protection - SUS_P" "0,1"
|
|
newline
|
|
hexmask.long.byte 0x0 24.--27. 1. "SUS,OCDS Suspend Control - SUS"
|
|
group.long 0xC++0x13
|
|
line.long 0x0 "PISEL0,Port Input Select Register 0"
|
|
bitfld.long 0x0 14.--15. "IST12HR,Input Select for T12HR" "0: Either signal T12HRA (if T12EXT = 0) or T12HRE..,1: Either signal T12HRB (if T12EXT = 0) or T12HRF..,2: Either signal T12HRC (if T12EXT = 0) or T12HRG..,3: Either signal T12HRD (if T12EXT = 0) or T12HRH.."
|
|
bitfld.long 0x0 12.--13. "ISPOS2,Input Select for CCPOS2" "0: P1.0,1: P2.2,2: P2.9,3: BEMFC.PH3_ZC_STS"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "ISPOS1,Input Select for CCPOS1" "0: P1.1,1: P2.4,2: P2.8,3: BEMFC.PH2_ZC_STS"
|
|
bitfld.long 0x0 8.--9. "ISPOS0,Input Select for CCPOS0" "0: P1.2,1: P2.3,2: P2.7,3: BEMFC.PH1_ZC_STS"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "ISTRP,Input Select for CTRAP" "0: P1.1,1: P2.6,2: ADC1.CMP0,3: CSC.OUT"
|
|
bitfld.long 0x0 4.--5. "ISCC72,Input Select for CC72" "0: P0.1,1: P2.4,2: P0.9,?"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "ISCC71,Input Select for CC71" "0: P1.0,1: P2.3,2: P0.6,3: SDADC.CMP1"
|
|
bitfld.long 0x0 0.--1. "ISCC70,Input Select for CC70" "0: P1.2,1: P2.2,2: P0.4,3: SDADC.CMP0"
|
|
line.long 0x4 "PISEL2,Port Input Select Register 2"
|
|
bitfld.long 0x4 7. "T13EXT,Extension for T13HR Inputs" "0: One of the signals T13HR[D:A] is selected.,1: One of the signals T13HR[H:E] is selected."
|
|
bitfld.long 0x4 6. "T12EXT,Extension for T12HR Inputs" "0: One of the signals T12HR[D:A] is selected.,1: One of the signals T12HR[H:E] is selected."
|
|
newline
|
|
bitfld.long 0x4 4.--5. "ISCNT13,Input Select for T13 Counting Input" "0: The T13 prescaler generates the counting events.,1: Bit TCTR4.T13CNT written with 1 is a counting..,2: The timer T13 is counting each rising edge..,3: The timer T13 is counting each falling edge.."
|
|
bitfld.long 0x4 2.--3. "ISCNT12,Input Select for T12 Counting Input" "0: The T12 prescaler generates the counting events.,1: Bit TCTR4.T12CNT written with 1 is a counting..,2: The timer T12 is counting each rising edge..,3: The timer T12 is counting each falling edge.."
|
|
newline
|
|
bitfld.long 0x4 0.--1. "IST13HR,Input Select for T13HR" "0: Either signal T13HRA (if T13EXT = 0) or T13HRE..,1: Either signal T13HRB (if T13EXT = 0) or T13HRF..,2: Either signal T13HRC (if T13EXT = 0) or T13HRG..,3: Either signal T13HRD (if T13EXT = 0) or T13HRH.."
|
|
line.long 0x8 "PISEL24,Port Input Select Register 24"
|
|
bitfld.long 0x8 4. "T1xEXT,Extension for T1xHR Inputs" "0: One of the signals T1xHR[D:A] is selected.,1: One of the signals T1xHR[H:E] is selected."
|
|
bitfld.long 0x8 2.--3. "ISCNT1x,Input Select for T1x Counting Input" "0: The T1x prescaler generates the counting events.,1: Bit TCTR4x.T1xCNT written with 1 is a counting..,2: The timer T1x is counting each rising edge..,3: The timer T1x is counting each falling edge.."
|
|
newline
|
|
bitfld.long 0x8 0.--1. "IST1xHR,Input Select for T1xHR" "0: Either signal T1xHRA (if T1xEXT = 0) or T1xHRE..,1: Either signal T1xHRB (if T1xEXT = 0) or T1xHRF..,2: Either signal T1xHRC (if T1xEXT = 0) or T1xHRG..,3: Either signal T1xHRD (if T1xEXT = 0) or T1xHRH.."
|
|
line.long 0xC "PISEL25,Port Input Select Register 25"
|
|
bitfld.long 0xC 4. "T1xEXT,Extension for T1xHR Inputs" "0: One of the signals T1xHR[D:A] is selected.,1: One of the signals T1xHR[H:E] is selected."
|
|
bitfld.long 0xC 2.--3. "ISCNT1x,Input Select for T1x Counting Input" "0: The T1x prescaler generates the counting events.,1: Bit TCTR4x.T1xCNT written with 1 is a counting..,2: The timer T1x is counting each rising edge..,3: The timer T1x is counting each falling edge.."
|
|
newline
|
|
bitfld.long 0xC 0.--1. "IST1xHR,Input Select for T1xHR" "0: Either signal T1xHRA (if T1xEXT = 0) or T1xHRE..,1: Either signal T1xHRB (if T1xEXT = 0) or T1xHRF..,2: Either signal T1xHRC (if T1xEXT = 0) or T1xHRG..,3: Either signal T1xHRD (if T1xEXT = 0) or T1xHRH.."
|
|
line.long 0x10 "PISEL26,Port Input Select Register 26"
|
|
bitfld.long 0x10 4. "T1xEXT,Extension for T1xHR Inputs" "0: One of the signals T1xHR[D:A] is selected.,1: One of the signals T1xHR[H:E] is selected."
|
|
bitfld.long 0x10 2.--3. "ISCNT1x,Input Select for T1x Counting Input" "0: The T1x prescaler generates the counting events.,1: Bit TCTR4x.T1xCNT written with 1 is a counting..,2: The timer T1x is counting each rising edge..,3: The timer T1x is counting each falling edge.."
|
|
newline
|
|
bitfld.long 0x10 0.--1. "IST1xHR,Input Select for T1xHR" "0: Either signal T1xHRA (if T1xEXT = 0) or T1xHRE..,1: Either signal T1xHRB (if T1xEXT = 0) or T1xHRF..,2: Either signal T1xHRC (if T1xEXT = 0) or T1xHRG..,3: Either signal T1xHRD (if T1xEXT = 0) or T1xHRH.."
|
|
group.long 0xF4++0x3
|
|
line.long 0x0 "PSLR,Passive State Level Register"
|
|
bitfld.long 0x0 7. "PSL73,Passive State Level of Output COUT73" "0: The passive level is 0.,1: The passive level is 1."
|
|
bitfld.long 0x0 5. "PSL_COUT72,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
newline
|
|
bitfld.long 0x0 4. "PSL_CC72,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
bitfld.long 0x0 3. "PSL_COUT71,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
newline
|
|
bitfld.long 0x0 2. "PSL_CC71,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
bitfld.long 0x0 1. "PSL_COUT70,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
newline
|
|
bitfld.long 0x0 0. "PSL_CC70,Compare Outputs Passive State Level" "0: The passive level is 0.,1: The passive level is 1."
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "T12,Timer T12 Counter Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T12CV,Timer T12 Counter Value"
|
|
group.long 0x30++0xB
|
|
line.long 0x0 "T12DT0_VAL,Dead-Time value Register CC70"
|
|
hexmask.long.byte 0x0 8.--15. 1. "DTM_FALL,Dead-Time fall"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DTM_RISE,Dead-Time rise"
|
|
line.long 0x4 "T12DT1_VAL,Dead-Time value Register CC71"
|
|
hexmask.long.byte 0x4 8.--15. 1. "DTM_FALL,Dead-Time fall"
|
|
hexmask.long.byte 0x4 0.--7. 1. "DTM_RISE,Dead-Time rise"
|
|
line.long 0x8 "T12DT2_VAL,Dead-Time value Register CC72"
|
|
hexmask.long.byte 0x8 8.--15. 1. "DTM_FALL,Dead-Time fall"
|
|
hexmask.long.byte 0x8 0.--7. 1. "DTM_RISE,Dead-Time rise"
|
|
group.long 0x2C++0x3
|
|
line.long 0x0 "T12DTC,Dead-Time Control Register for Timer T12 Low"
|
|
rbitfld.long 0x0 10. "DTR2,Dead-Time Run Indication Bit 2" "0: Dead-Time Counter 2 is currently in the passive..,1: Dead-Time Counter 2 is currently in the active.."
|
|
rbitfld.long 0x0 9. "DTR1,Dead-Time Run Indication Bit 1" "0: Dead-Time Counter 1 is currently in the passive..,1: Dead-Time Counter 1 is currently in the active.."
|
|
newline
|
|
rbitfld.long 0x0 8. "DTR0,Dead-Time Run Indication Bit 0" "0: Dead-Time Counter 0 is currently in the passive..,1: Dead-Time Counter 0 is currently in the active.."
|
|
bitfld.long 0x0 2. "DTE2,Dead-Time Enable Bit 2" "0: Dead-time generation is disabled. The..,1: Dead-time generation is enabled. The.."
|
|
newline
|
|
bitfld.long 0x0 1. "DTE1,Dead-Time Enable Bit 1" "0: Dead-time generation is disabled. The..,1: Dead-time generation is enabled. The.."
|
|
bitfld.long 0x0 0. "DTE0,Dead-Time Enable Bit 0" "0: Dead-time generation is disabled. The..,1: Dead-time generation is enabled. The.."
|
|
group.long 0x3C++0x3
|
|
line.long 0x0 "T12DTINSEL,Dead-Time Input Selection Register (Demo in Windows)"
|
|
bitfld.long 0x0 8.--9. "DTINSEL2,Deadtime Input selection 2" "0: State Bit of Compare Channel 72,1: State Bit of Compare Channel 72 B,2: Run Bit from T16 Timer,3: State Bit of Timer16"
|
|
bitfld.long 0x0 4.--5. "DTINSEL1,Deadtime Input selection 1" "0: State Bit of Compare Channel 71,1: State Bit of Compare Channel 71 B,2: Run Bit from T15 Timer,3: State Bit of Timer15"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "DTINSEL0,Deadtime Input selection 0" "0: State Bit of Compare Channel 70,1: State Bit of Compare Channel 70 B,2: Run Bit from T14 Timer,3: State Bit of Timer14"
|
|
group.long 0xC0++0x3
|
|
line.long 0x0 "T12MSEL,T12 Capture/Compare Mode Select Register"
|
|
bitfld.long 0x0 15. "DBYP,Delay Bypass" "0: The delay bypass is not active. The dead-time..,1: The delay bypass is active. The dead-time.."
|
|
bitfld.long 0x0 12.--14. "HSYNC,Hall Synchronization" "0: CCPOSx edge,1: T13 compare match,2: T13 period match,3: Hall sampling off.,4: T12 period match UP,5: T12 one match DOWN,6: A T12 compare match 1 UP,7: A T12 compare match 1 DOWN"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--11. 1. "MSEL72,Capture/Compare Mode Selection MSEL7x (x=0 1 2)"
|
|
hexmask.long.byte 0x0 4.--7. 1. "MSEL71,Capture/Compare Mode Selection MSEL7x (x=0 1 2)"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--3. 1. "MSEL70,Capture/Compare Mode Selection MSEL7x (x=0 1 2)"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "T12PR,Timer T12 Period Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T12PV,T12 Period Value"
|
|
group.long 0x80++0x3
|
|
line.long 0x0 "T13PR,Timer T13 Period Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xPV,T1x Period Value"
|
|
group.long 0x70++0x3
|
|
line.long 0x0 "T13R,Timer T13 Counter Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xCV,Timer T1x Counter Value"
|
|
group.long 0x84++0x3
|
|
line.long 0x0 "T14PR,Timer T14 Period Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xPV,T1x Period Value"
|
|
group.long 0x74++0x3
|
|
line.long 0x0 "T14R,Timer T14 Counter Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xCV,Timer T1x Counter Value"
|
|
group.long 0x88++0x3
|
|
line.long 0x0 "T15PR,Timer T15 Period Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xPV,T1x Period Value"
|
|
group.long 0x78++0x3
|
|
line.long 0x0 "T15R,Timer T15 Counter Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xCV,Timer T1x Counter Value"
|
|
group.long 0x8C++0x3
|
|
line.long 0x0 "T16PR,Timer T16 Period Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xPV,T1x Period Value"
|
|
group.long 0x7C++0x3
|
|
line.long 0x0 "T16R,Timer T16 Counter Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T1xCV,Timer T1x Counter Value"
|
|
group.long 0xC4++0x17
|
|
line.long 0x0 "TCTR0,Timer Control Register 0"
|
|
rbitfld.long 0x0 13. "STE13,Timer T13 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
rbitfld.long 0x0 12. "T13R,Timer T13 Run Bit" "0: Timer T13 is stopped.,1: Timer T13 is running."
|
|
newline
|
|
bitfld.long 0x0 11. "T13PRE,Timer T13 Prescaler Bit" "0: The additional prescaler for T13 is disabled.,1: The additional prescaler for T13 is enabled."
|
|
bitfld.long 0x0 7. "CTM,T12 Operating Mode" "0: T12 always counts up and continues counting from..,1: T12 counts down after detecting a period-match.."
|
|
newline
|
|
rbitfld.long 0x0 6. "CDIR,Count Direction of Timer T12" "0: T12 counts up.,1: T12 counts down."
|
|
rbitfld.long 0x0 5. "STE12,Timer T12 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
newline
|
|
rbitfld.long 0x0 4. "T12R,Timer T12 Run Bit" "0: Timer T12 is stopped.,1: Timer T12 is running."
|
|
bitfld.long 0x0 3. "T12PRE,Timer T12 Prescaler Bit" "0: The additional prescaler for T12 is disabled.,1: The additional prescaler for T12 is enabled."
|
|
line.long 0x4 "TCTR1,Timer Control Register 1"
|
|
rbitfld.long 0x4 15. "STE13,Timer T13 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
rbitfld.long 0x4 14. "STE12,Timer T12 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
newline
|
|
rbitfld.long 0x4 13. "STE16,Timer T16 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
rbitfld.long 0x4 12. "T16R,Timer T16 Run Bit" "0: Timer T16 is stopped.,1: Timer T16 is running."
|
|
newline
|
|
rbitfld.long 0x4 9. "STE15,Timer T15 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
rbitfld.long 0x4 8. "T15R,Timer T15 Run Bit" "0: Timer T15 is stopped.,1: Timer T15 is running."
|
|
newline
|
|
rbitfld.long 0x4 5. "STE14,Timer T14 Shadow Transfer Enable" "0: The shadow register transfer is disabled.,1: The shadow register transfer is enabled."
|
|
rbitfld.long 0x4 4. "T14R,Timer T14 Run Bit" "0: Timer T14 is stopped.,1: Timer T14 is running."
|
|
newline
|
|
bitfld.long 0x4 3. "T1xPRE,Timer T14 / 15 /16 Prescaler Bit" "0: The additional prescaler for T12 is disabled.,1: The additional prescaler for T12 is enabled."
|
|
line.long 0x8 "TCTR2,Timer Control Register 2"
|
|
bitfld.long 0x8 10.--11. "T13RSEL,Timer T13 External Run Selection" "0: The external setting of T13R is disabled.,1: Bit T13R is set if a rising edge of signal T13HR..,2: Bit T13R is set if a falling edge of signal..,3: Bit T13R is set if an edge of signal T13HR is.."
|
|
bitfld.long 0x8 8.--9. "T12RSEL,Timer T12 External Run Selection" "0: The external setting of T12R is disabled.,1: Bit T12R is set if a rising edge of signal T12HR..,2: Bit T12R is set if a falling edge of signal..,3: Bit T12R is set if an edge of signal T12HR is.."
|
|
newline
|
|
bitfld.long 0x8 5.--6. "T13TED,Timer T13 Trigger Event Direction" "0,1,2,3"
|
|
bitfld.long 0x8 2.--4. "T13TEC,T13 Trigger Event Control" "0,1,2,3,4,5,6,7"
|
|
newline
|
|
bitfld.long 0x8 1. "T13SSC,Timer T13 Single Shot Control" "0: No hardware action on T13R,1: The single-shot mode is enabled the bit T13R is.."
|
|
bitfld.long 0x8 0. "T12SSC,Timer T12 Single Shot Control" "0: The single-shot mode is disabled no hardware..,1: The single shot mode is enabled the bit T12R is.."
|
|
line.long 0xC "TCTR24,Timer Control Register 24"
|
|
bitfld.long 0xC 8.--9. "T1xRSEL,Timer T1x External Run Selection" "0: The external setting of T1xR is disabled.,1: Bit T1xR is set if a rising edge of signal T1xHR..,2: Bit T1xR is set if a falling edge of signal..,3: Bit T1xR is set if an edge of signal T1xHR is.."
|
|
bitfld.long 0xC 4.--5. "T1xTED,Timer T1x Trigger Event Direction" "0,1,2,3"
|
|
newline
|
|
bitfld.long 0xC 1.--3. "T1xTEC,T1x Trigger Event Control" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0xC 0. "T1xSSC,Timer T1x Single Shot Control" "0: The single-shot mode is disabled no hardware..,1: The single shot mode is enabled the bit T12R is.."
|
|
line.long 0x10 "TCTR25,Timer Control Register 25"
|
|
bitfld.long 0x10 8.--9. "T1xRSEL,Timer T1x External Run Selection" "0: The external setting of T1xR is disabled.,1: Bit T1xR is set if a rising edge of signal T1xHR..,2: Bit T1xR is set if a falling edge of signal..,3: Bit T1xR is set if an edge of signal T1xHR is.."
|
|
bitfld.long 0x10 4.--5. "T1xTED,Timer T1x Trigger Event Direction" "0,1,2,3"
|
|
newline
|
|
bitfld.long 0x10 1.--3. "T1xTEC,T1x Trigger Event Control" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x10 0. "T1xSSC,Timer T1x Single Shot Control" "0: The single-shot mode is disabled no hardware..,1: The single shot mode is enabled the bit T12R is.."
|
|
line.long 0x14 "TCTR26,Timer Control Register 26"
|
|
bitfld.long 0x14 8.--9. "T1xRSEL,Timer T1x External Run Selection" "0: The external setting of T1xR is disabled.,1: Bit T1xR is set if a rising edge of signal T1xHR..,2: Bit T1xR is set if a falling edge of signal..,3: Bit T1xR is set if an edge of signal T1xHR is.."
|
|
bitfld.long 0x14 4.--5. "T1xTED,Timer T1x Trigger Event Direction" "0,1,2,3"
|
|
newline
|
|
bitfld.long 0x14 1.--3. "T1xTEC,T1x Trigger Event Control" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x14 0. "T1xSSC,Timer T1x Single Shot Control" "0: The single-shot mode is disabled no hardware..,1: The single shot mode is enabled the bit T12R is.."
|
|
wgroup.long 0x144++0x3
|
|
line.long 0x0 "TCTR3,Timer Control Register 3"
|
|
bitfld.long 0x0 12. "T16STD,Timer T16 Shadow Transfer Disable" "0: no change to STE16,1: STE16 is reset without triggering the shadow.."
|
|
bitfld.long 0x0 11. "T15STD,Timer T15 Shadow Transfer Disable" "0: no change to STE15,1: STE15 is reset without triggering the shadow.."
|
|
newline
|
|
bitfld.long 0x0 10. "T14STD,Timer T14 Shadow Transfer Disable" "0: no change to STE14,1: STE14 is reset without triggering the shadow.."
|
|
bitfld.long 0x0 9. "T13STD,Timer T13 Shadow Transfer Disable" "0: No effect on STE13,1: STE13 is reset without triggering the shadow.."
|
|
newline
|
|
bitfld.long 0x0 8. "T12STD,Timer T12 Shadow Transfer Disable" "0: no change to STE12,1: STE12 is reset without triggering the shadow.."
|
|
bitfld.long 0x0 4. "T16STR,Timer T16 Shadow Transfer Request" "0: no change to STE16,1: STE16 is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x0 3. "T15STR,Timer T15 Shadow Transfer Request" "0: no change to STE15,1: STE15 is set enabling the shadow transfer."
|
|
bitfld.long 0x0 2. "T14STR,Timer T14 Shadow Transfer Request" "0: no change to STE14,1: STE14 is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x0 1. "T13STR,Timer T13 Shadow Transfer Request" "0: No effect on STE13,1: STE13 is set enabling the shadow transfer."
|
|
bitfld.long 0x0 0. "T12STR,Timer T12 Shadow Transfer Request" "0: no change to STE12,1: STE12 is set enabling the shadow transfer."
|
|
wgroup.long 0xDC++0xF
|
|
line.long 0x0 "TCTR4,Timer Control Register 4"
|
|
bitfld.long 0x0 15. "T13STD,Timer T13 Shadow Transfer Disable" "0: No effect on STE13,1: STE13 is reset without triggering the shadow.."
|
|
bitfld.long 0x0 14. "T13STR,Timer T13 Shadow Transfer Request" "0: No effect on STE13,1: STE13 is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x0 13. "T13CNT,Timer T13 Count Event" "0: No effect on T13,1: If enabled (PISEL2) timer T13 counts one step."
|
|
bitfld.long 0x0 10. "T13RES,Timer T13 Reset" "0: No effect on T13.,1: The T13 counter register is reset to zero. The.."
|
|
newline
|
|
bitfld.long 0x0 9. "T13RS,Timer T13 Run Set" "0: T13R is not changed.,1: T13R is set T13 counts."
|
|
bitfld.long 0x0 8. "T13RR,Timer T13 Run Reset" "0: T13R is not changed.,1: T13R is cleared T13 stops counting."
|
|
newline
|
|
bitfld.long 0x0 7. "T12STD,Timer T12 Shadow Transfer Disable" "0: no change to STE12,1: STE12 is reset without triggering the shadow.."
|
|
bitfld.long 0x0 6. "T12STR,Timer T12 Shadow Transfer Request" "0: no change to STE12,1: STE12 is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x0 5. "T12CNT,Timer T12 Count Event" "0: No effect on T12,1: If enabled (PISEL2) timer T12 counts one step."
|
|
bitfld.long 0x0 3. "DTRES,Dead-Time Counter Reset" "0: No effect on the dead-time counters.,1: The three dead-time counter channels are reset.."
|
|
newline
|
|
bitfld.long 0x0 2. "T12RES,Timer T12 Reset" "0: No change on T12.,1: The T12 counter register is reset to zero. The.."
|
|
bitfld.long 0x0 1. "T12RS,Timer T12 Run Set" "0: T12R is not changed.,1: T12R is set T12 counts."
|
|
newline
|
|
bitfld.long 0x0 0. "T12RR,Timer T12 Run Reset" "0: T12R is not changed.,1: T12R is cleared T12 stops counting."
|
|
line.long 0x4 "TCTR44,Timer Control Register 44"
|
|
bitfld.long 0x4 6. "T1xSTD,Timer T1x Shadow Transfer Disable" "0: Noaction,1: STE1x is reset without triggering the shadow.."
|
|
bitfld.long 0x4 5. "T1xSTR,Timer T1x Shadow Transfer Request" "0: Noaction,1: STE1x is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x4 4. "T1xCNT,Timer T1x Count Event" "0: Noaction,1: If enabled (PISEL2x) timer T1x counts one step."
|
|
bitfld.long 0x4 2. "T1xRES,Timer T1x Reset" "0: No effect on T1x.,1: The T1x counter register is reset to zero. The.."
|
|
newline
|
|
bitfld.long 0x4 1. "T1xRS,Timer T1x Run Set" "0: T1xR is not influenced.,1: T1xR is set T1x counts."
|
|
bitfld.long 0x4 0. "T1xRR,Timer T1x Run Reset" "0: T1xR is not influenced.,1: T1xR is cleared T1x stops counting."
|
|
line.long 0x8 "TCTR45,Timer Control Register 45"
|
|
bitfld.long 0x8 6. "T1xSTD,Timer T1x Shadow Transfer Disable" "0: Noaction,1: STE1x is reset without triggering the shadow.."
|
|
bitfld.long 0x8 5. "T1xSTR,Timer T1x Shadow Transfer Request" "0: Noaction,1: STE1x is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0x8 4. "T1xCNT,Timer T1x Count Event" "0: Noaction,1: If enabled (PISEL2x) timer T1x counts one step."
|
|
bitfld.long 0x8 2. "T1xRES,Timer T1x Reset" "0: No effect on T1x.,1: The T1x counter register is reset to zero. The.."
|
|
newline
|
|
bitfld.long 0x8 1. "T1xRS,Timer T1x Run Set" "0: T1xR is not influenced.,1: T1xR is set T1x counts."
|
|
bitfld.long 0x8 0. "T1xRR,Timer T1x Run Reset" "0: T1xR is not influenced.,1: T1xR is cleared T1x stops counting."
|
|
line.long 0xC "TCTR46,Timer Control Register 46"
|
|
bitfld.long 0xC 6. "T1xSTD,Timer T1x Shadow Transfer Disable" "0: Noaction,1: STE1x is reset without triggering the shadow.."
|
|
bitfld.long 0xC 5. "T1xSTR,Timer T1x Shadow Transfer Request" "0: Noaction,1: STE1x is set enabling the shadow transfer."
|
|
newline
|
|
bitfld.long 0xC 4. "T1xCNT,Timer T1x Count Event" "0: Noaction,1: If enabled (PISEL2x) timer T1x counts one step."
|
|
bitfld.long 0xC 2. "T1xRES,Timer T1x Reset" "0: No effect on T1x.,1: The T1x counter register is reset to zero. The.."
|
|
newline
|
|
bitfld.long 0xC 1. "T1xRS,Timer T1x Run Set" "0: T1xR is not influenced.,1: T1xR is set T1x counts."
|
|
bitfld.long 0xC 0. "T1xRR,Timer T1x Run Reset" "0: T1xR is not influenced.,1: T1xR is cleared T1x stops counting."
|
|
group.long 0xF0++0x3
|
|
line.long 0x0 "TRPCTR,Trap Control Register"
|
|
bitfld.long 0x0 15. "TRPPEN,Trap Pin Enable - TRPPEN" "0: Disable,1: Enable"
|
|
bitfld.long 0x0 14. "TRPEN13,Trap Enable Control for Timer T13" "0: The trap functionality for T13 is disabled.,1: The trap functionality for T13 is enabled. The.."
|
|
newline
|
|
hexmask.long.byte 0x0 8.--13. 1. "TRPEN,Trap Enable Control"
|
|
bitfld.long 0x0 2. "TRPM2,Trap Mode Control Bit 2 - TRPM2" "0: Const_0,1: Const_1"
|
|
newline
|
|
bitfld.long 0x0 1. "TRPM1,Trap Mode Control Bit 1 - TRPM1" "?,1: TRPM1"
|
|
bitfld.long 0x0 0. "TRPM0,Trap Mode Control Bit 0 - TRPM0" "0: TRPM0,?"
|
|
group.long 0x140++0x3
|
|
line.long 0x0 "T_CLK_CTRL,Timer Clock Selection"
|
|
bitfld.long 0x0 13. "FDIV1_SEL,FDIV1 Mode Selection" "0: T_FDIV0[7:0] = Q; TFDIV[15:8] = P,1: T_FDIV0[9:0] = Q; TFDIV[15:10] = P"
|
|
bitfld.long 0x0 12. "FDIV0_SEL,FDIV0 Mode Selection" "0: T_FDIV0[7:0] = Q; TFDIV[15:8] = P,1: T_FDIV0[9:0] = Q; TFDIV[15:10] = P"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "DT_CLK_SEL,Clock Selector for dead time control" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
bitfld.long 0x0 8.--9. "T16_CLK_SEL,Clock selector for Timer 16" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "T15_CLK_SEL,Clock selector for Timer 15" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
bitfld.long 0x0 4.--5. "T14_CLK_SEL,Clock selector for Timer 14" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "T13_CLK_SEL,Clock selector for Timer 13" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
bitfld.long 0x0 0.--1. "T12_CLK_SEL,Clock selector for Timer 12" "0: No Clock Division,1: Clock from Clock Divider 0,2: Clock from Clock Divider 1,?"
|
|
group.long 0x138++0x7
|
|
line.long 0x0 "T_FDIV0,Fractional Divider0"
|
|
hexmask.long.word 0x0 0.--15. 1. "PQ,PQ"
|
|
line.long 0x4 "T_FDIV1,Fractional Divider1"
|
|
hexmask.long.word 0x4 0.--15. 1. "PQ,PQ"
|
|
tree.end
|
|
tree "CPU (CPU Processor)"
|
|
base ad:0xE000E000
|
|
rgroup.long 0xD3C++0x3
|
|
line.long 0x0 "AFSR,Auxiliary Fault Status Register"
|
|
hexmask.long 0x0 0.--31. 1. "AUXFAULT,Additional system fault information"
|
|
group.long 0xD0C++0x3
|
|
line.long 0x0 "AIRCR,Application Interrupt/Reset Control Register"
|
|
hexmask.long.word 0x0 16.--31. 1. "VECTKEY,Vector Key"
|
|
rbitfld.long 0x0 15. "ENDIANNESS,Data endianness\n" "0: little endian,1: big endian"
|
|
newline
|
|
bitfld.long 0x0 8.--10. "PRIGROUP,Priority Grouping" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 2. "SYSRESETREQ,System Reset Request" "0: no effect,1: request system reset"
|
|
newline
|
|
bitfld.long 0x0 1. "VECTCLRACTIVE,Active status information clear for fixed and configurable exception" "0: no information cleared,1: all active status information are cleared for.."
|
|
bitfld.long 0x0 0. "VECTRESET,Local system reset" "0: No local system reset,1: local system reset"
|
|
group.long 0xD38++0x3
|
|
line.long 0x0 "BFAR,Bus Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDRESS,Address of the location that generated a BusFault"
|
|
group.long 0xD14++0x3
|
|
line.long 0x0 "CCR,Configuration Control Register"
|
|
bitfld.long 0x0 9. "STKALIGN,Stack frame alignment on exception entry" "0: the exception entry sequence guarantees an..,1: the exception entry sequence guarantees an.."
|
|
bitfld.long 0x0 8. "BFHFMIGN,Effect of precise data access faults on handlers running at a priority -1 or -2" "0: precise data access fault causes a lockup,1: handler ignores the fault"
|
|
newline
|
|
bitfld.long 0x0 4. "DIV_0_TRP,Trap divide by zero enable" "0: do not trap divide by 0,1: trap divide by 0"
|
|
bitfld.long 0x0 3. "UNALIGN_TRP,Unaligned access traps enable" "0: trapping disabled,1: trapping enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "USERSETMPEND,Unprivileged software access to the STIR enable" "0: unprivileged software cannot access register STIR.,1: unprivileged software can access register STIR."
|
|
bitfld.long 0x0 0. "NONBASETHRDENA,Control of the processor entry point into the Thread mode" "0: any attempt to enter Thread mode at an execution..,1: the processor can enter Thread mode at any.."
|
|
group.long 0xD28++0x3
|
|
line.long 0x0 "CFSR,Configurable Fault Status Register"
|
|
bitfld.long 0x0 25. "DIVBYZERO,Divide by zero UsageFault" "0: No Divide by zero error has occurred.,1: A divide by zero error has occurred."
|
|
bitfld.long 0x0 24. "UNALIGNED,Unaligned access UsageFault" "0: No unaligned access error has occurred.,1: A unaligned access error has occurred."
|
|
newline
|
|
bitfld.long 0x0 19. "NOCP,No coprocessor UsageFault" "0: No coprocessor access error has occurred.,1: A coprocessor access error has occurred."
|
|
bitfld.long 0x0 18. "INVPC,Invalid PC load UsageFault" "0: No integrity check error has occurred.,1: A integrity check error has occurred."
|
|
newline
|
|
bitfld.long 0x0 17. "INVSTATE,Invalid state UsageFault" "0: EPSR.T bit and EPSR.IT bits are valid for..,1: Instruction executed with invalid EPSR.T or.."
|
|
bitfld.long 0x0 16. "UNDEFINSTR,Undefined instruction UsageFault" "0: No Undefined Instruction Usage fault has occurred.,1: The processor hat attempted to execute an.."
|
|
newline
|
|
bitfld.long 0x0 15. "BFARVALID,BusFault Address Register (BFAR) valid flag" "0: BFAR does not have valid contents.,1: BFAR has valid contents."
|
|
bitfld.long 0x0 13. "LSPERR,BusFault during FP lazy state preservation" "0: No bus fault occurred during FP lazy state..,1: A bus fault occurred during FP lazy state.."
|
|
newline
|
|
bitfld.long 0x0 12. "STKERR,BusFault on stacking for exception entry" "0: No derived bus fault occurred,1: A derived bus fault occurred on exception entry"
|
|
bitfld.long 0x0 11. "UNSTKERR,BusFault on unstacking for a return from exception" "0: No derived bus fault occurred,1: A derived bus fault occurred on exception return"
|
|
newline
|
|
bitfld.long 0x0 10. "IMPRECISERR,Imprecise data bus error" "0: No precise data access error has occurred,1: An imprecise data access error has occurred."
|
|
bitfld.long 0x0 9. "PRECISERR,Precise data bus error" "0: No precise data access error has occurred,1: An imprecise data access error has occurred and.."
|
|
newline
|
|
bitfld.long 0x0 8. "IBUSERR,Instruction bus error" "0: No bus fault on an instruction prefetch has..,1: A bus fault on an instruction prefetch has.."
|
|
bitfld.long 0x0 7. "MMARVALID,MemManage Fault Address Register (MMFAR) valid flag" "0: MMFAR does not have valid contents.,1: MMFAR has valid contents."
|
|
newline
|
|
bitfld.long 0x0 5. "MLSPERR,MemManage fault during FP lazy state preservation" "0: No MemManage fault occurred during FP lazy state..,1: A MemManage fault occurred during FP lazy state.."
|
|
bitfld.long 0x0 4. "MSTERR,MemManage fault on stacking for exception entry" "0: No derived MemManage fault occurred,1: A derived MemManage fault occurred on exception.."
|
|
newline
|
|
bitfld.long 0x0 3. "MUNSTKERR,MemManage fault on unstacking for a return from exception" "0: No derived MemManage fault occurred,1: A derived MemManage fault occurred on exception.."
|
|
bitfld.long 0x0 1. "DACCVIOL,Data access violation flag" "0: No data access violation has occurred.,1: Data access violation. The MMAR shows the data.."
|
|
newline
|
|
bitfld.long 0x0 0. "IACCVIOL,Instruction access violation flag" "0: No MPU or Execute Never (XN) default memory map..,1: An MPU or Execute Never (XN) default memory map.."
|
|
rgroup.long 0xD00++0x3
|
|
line.long 0x0 "CPUID,CPU ID Base Register"
|
|
hexmask.long.byte 0x0 24.--31. 1. "IMPLEMENTER,Implementer Code"
|
|
hexmask.long.byte 0x0 20.--23. 1. "VARIANT,Variant Number"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "ARCHITECTURE,Architecture"
|
|
hexmask.long.word 0x0 4.--15. 1. "PARTNO,Part Number"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--3. 1. "REVISION,Revision Number"
|
|
group.long 0xDF8++0x3
|
|
line.long 0x0 "DCRDR,Debug Core Register Data Register"
|
|
hexmask.long 0x0 0.--31. 1. "DBGTMP,Data written to the register selected by DCRSR"
|
|
group.long 0xDF4++0x3
|
|
line.long 0x0 "DCRSR,Debug Core Register Selector Register"
|
|
bitfld.long 0x0 16. "REGWnR,Access type for the transfer" "0: Read Access,1: Write Access"
|
|
hexmask.long.byte 0x0 0.--6. 1. "REGSEL,Selection of the ARM core register or special-purpose register to transfer"
|
|
group.long 0xDFC++0x3
|
|
line.long 0x0 "DEMCR,Debug Exception and Monitor Control Register"
|
|
bitfld.long 0x0 24. "DWTENA,Global enable for the DW unit" "0: DWT disabled. DWT registers return unknown..,1: DWT enabled"
|
|
bitfld.long 0x0 19. "MON_REQ,Debug Monitor Semaphore Bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 18. "MON_STEP,Step Request" "0: Do not step the processor,1: Step the processor"
|
|
bitfld.long 0x0 17. "MON_PEND,Debug Monitor Pending Exception Set/Clear" "0: Clear the status of the DebugMonitor exception..,1: Set the status of the DebugMonitor exception to.."
|
|
newline
|
|
bitfld.long 0x0 16. "MON_EN,Debug Monitor Exception Enable" "0: Debug Monitor Exception disabled,1: Debug Monitor Exception enabled"
|
|
bitfld.long 0x0 10. "VC_HARDERR,Halting debug trap enable on a HardFault exception" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
newline
|
|
bitfld.long 0x0 9. "VC_INTERR,Halting debug trap enable on a fault during an exception entry or return" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
bitfld.long 0x0 8. "VC_BUSERR,Halting debug trap enable on a BusFault exception" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
newline
|
|
bitfld.long 0x0 7. "VC_STATERR,Halting debug trap enable on a UsageFault caused by a state information error" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
bitfld.long 0x0 6. "VC_CHKERR,Halting debug trap enable on a UsageFault caused by a checking error" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
newline
|
|
bitfld.long 0x0 5. "VC_NOCPERR,Halting debug trap enable on a UsageFault caused by an access to the coprocessor" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
bitfld.long 0x0 4. "VC_MMERR,Halting debug trap enable on a MemManage exception" "0: Halting debug trap disabled,1: Halting debug trap enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "VC_CORERESET,Reset vector catch enable\n" "0: Reset Vector Catch disabled,1: Reset Vector Catch enabled this causes a local.."
|
|
group.long 0xDF0++0x3
|
|
line.long 0x0 "DHCSR,Debug Halting Control and Status Register"
|
|
rbitfld.long 0x0 25. "S_RESET_ST,Processor reset flag since last read" "0: No reset since last DHCSR read,1: At least one reset since last DHCSR read"
|
|
rbitfld.long 0x0 24. "S_RETIRE_ST,Complete instruction flag since last read" "0: No instruction has completed since last DHCSR read,1: At least one instructions has completed since.."
|
|
newline
|
|
rbitfld.long 0x0 19. "S_LOCKUP,Processor lockup state\n" "0: Notlockedup,1: Lockedup"
|
|
rbitfld.long 0x0 18. "S_SLEEP,Processor sleep state" "0: Notsleeping,1: Sleeping"
|
|
newline
|
|
rbitfld.long 0x0 17. "S_HALT,Processor halt in debug state" "0: NotinDebugstate,1: InDebugstate"
|
|
rbitfld.long 0x0 16. "S_REGRDY,Handshake flag for transfers through the DCRDR" "0: There has been a write to the DCRDR but the..,1: The transfer to or from the DCRDR is complete"
|
|
newline
|
|
bitfld.long 0x0 5. "C_SNAPSTALL,Allow imprecise entry to Debug state" "0: no action,1: Allow imprecise entry to Debug state for example.."
|
|
bitfld.long 0x0 3. "C_MASKINTS,Mask external interrupts SysTick and PendSV" "0: no action,1: Allow imprecise entry to Debug state for example.."
|
|
newline
|
|
bitfld.long 0x0 2. "C_STEP,Processor Step" "0: Single-stepping disabled,1: Single-stepping enabled"
|
|
bitfld.long 0x0 1. "C_HALT,Processor Halt" "0: Request a halted processor to run,1: Request a running processor to halt"
|
|
newline
|
|
bitfld.long 0x0 0. "C_DEBUGEN,Debug enable" "0: Halting debug disabled,1: Halting debug enabled"
|
|
group.long 0xD2C++0x3
|
|
line.long 0x0 "HFSR,Hard Fault Status Register"
|
|
bitfld.long 0x0 31. "DEBUGEVT,Debug Event" "0: No Debug event has occurred,1: Debug event has occurred. The Debug Fault Status.."
|
|
bitfld.long 0x0 30. "FORCED,Forced HardFault flag" "0: No priority escalation has occurred,1: Processor has escalated a configurable priority.."
|
|
newline
|
|
bitfld.long 0x0 1. "VECTTBL,BusFault flag on a vector table read during exception processing" "0: No vector table read fault has occurred,1: Vector table read fault has occurred"
|
|
group.long 0xD04++0x3
|
|
line.long 0x0 "ICSR,Interrupt Control State Register"
|
|
bitfld.long 0x0 31. "NMIPENDSET,NMI set pending" "0: an NMI exception is not pending on a read..,1: an NMI exception is pending on a read operation.."
|
|
bitfld.long 0x0 28. "PENDSVSET,PendSV set pending" "0: PendSV is not pending on a read operation there..,1: PendSV is pending on a read operation the status.."
|
|
newline
|
|
bitfld.long 0x0 27. "PENDSVCLR,PendSV clear pending" "0: no effect,1: remove pending status"
|
|
bitfld.long 0x0 26. "PENDSTSET,SysTick exception set pending" "0: the SysTick is not pending on a read operation..,1: the SysTick is pending on a read operation the.."
|
|
newline
|
|
bitfld.long 0x0 25. "PENDSTCLR,SysTick exception clear pending" "0: no effect,1: the pending status is removed"
|
|
rbitfld.long 0x0 23. "ISRPREEMPT,Service of a pending exception on exit from debug halt state" "0: will not service,1: will service a pending exception"
|
|
newline
|
|
rbitfld.long 0x0 22. "ISRPending,External interrupt generated by the NVIC pending flag" "0: no external interrupt is pending,1: external interrupt is pending"
|
|
hexmask.long.word 0x0 12.--20. 1. "VECTPending,Exception number with the highest priority pending enabled exception"
|
|
newline
|
|
rbitfld.long 0x0 11. "RETTOBASE,Presence of preempted active exceptions" "0: There is an active exception other than the..,1: There is no active exception other than any.."
|
|
hexmask.long.word 0x0 0.--8. 1. "VECTACTIVE,Active exception number"
|
|
rgroup.long 0x4++0x3
|
|
line.long 0x0 "ICT,Interrupt Controller Type"
|
|
hexmask.long.byte 0x0 0.--4. 1. "INTLINESNUM,Total number of interrupt lines"
|
|
group.long 0xD34++0x3
|
|
line.long 0x0 "MMFAR,MemManage Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 1. "ADDRESS,Address of the location that generated a MemManage fault"
|
|
rgroup.long 0x300++0x3
|
|
line.long 0x0 "NVIC_IABR,Active Bit Register"
|
|
bitfld.long 0x0 31. "IRQACTIVE31,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 30. "IRQACTIVE30,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 29. "IRQACTIVE29,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 28. "IRQACTIVE28,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 27. "IRQACTIVE27,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 26. "IRQACTIVE26,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 25. "IRQACTIVE25,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 24. "IRQACTIVE24,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 23. "IRQACTIVE23,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 22. "IRQACTIVE22,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 21. "IRQACTIVE21,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 20. "IRQACTIVE20,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 19. "IRQACTIVE19,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 18. "IRQACTIVE18,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 17. "IRQACTIVE17,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 16. "IRQACTIVE16,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 15. "IRQACTIVE15,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 14. "IRQACTIVE14,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 13. "IRQACTIVE13,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 12. "IRQACTIVE12,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 11. "IRQACTIVE11,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 10. "IRQACTIVE10,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 9. "IRQACTIVE9,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 8. "IRQACTIVE8,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 7. "IRQACTIVE7,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 6. "IRQACTIVE6,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 5. "IRQACTIVE5,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 4. "IRQACTIVE4,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 3. "IRQACTIVE3,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 2. "IRQACTIVE2,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
newline
|
|
bitfld.long 0x0 1. "IRQACTIVE1,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
bitfld.long 0x0 0. "IRQACTIVE0,IRQx interrupt active flag" "0: the associated interrupt is disabled for a read..,1: the associated interrupt is enabled for a read.."
|
|
group.long 0x180++0x3
|
|
line.long 0x0 "NVIC_ICER,Interrupt Clear-Enable"
|
|
bitfld.long 0x0 31. "IRQCLREN31,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 30. "IRQCLREN30,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 29. "IRQCLREN29,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 28. "IRQCLREN28,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 27. "IRQCLREN27,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 26. "IRQCLREN26,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 25. "IRQCLREN25,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 24. "IRQCLREN24,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 23. "IRQCLREN23,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 22. "IRQCLREN22,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 21. "IRQCLREN21,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 20. "IRQCLREN20,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 19. "IRQCLREN19,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 18. "IRQCLREN18,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 17. "IRQCLREN17,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 16. "IRQCLREN16,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 15. "IRQCLREN15,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 14. "IRQCLREN14,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 13. "IRQCLREN13,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 12. "IRQCLREN12,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 11. "IRQCLREN11,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 10. "IRQCLREN10,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 9. "IRQCLREN9,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 8. "IRQCLREN8,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 7. "IRQCLREN7,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 6. "IRQCLREN6,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 5. "IRQCLREN5,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 4. "IRQCLREN4,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 3. "IRQCLREN3,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 2. "IRQCLREN2,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
newline
|
|
bitfld.long 0x0 1. "IRQCLREN1,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
bitfld.long 0x0 0. "IRQCLREN0,IRQx interrupt clear enable" "0: the associated interrupt is disabled on a read..,1: the associated interrupt is enabled on a read.."
|
|
group.long 0x280++0x3
|
|
line.long 0x0 "NVIC_ICPR,Interrupt Clear-Pending"
|
|
bitfld.long 0x0 31. "IRQCLRPEND31,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 30. "IRQCLRPEND30,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 29. "IRQCLRPEND29,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 28. "IRQCLRPEND28,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 27. "IRQCLRPEND27,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 26. "IRQCLRPEND26,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 25. "IRQCLRPEND25,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 24. "IRQCLRPEND24,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 23. "IRQCLRPEND23,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 22. "IRQCLRPEND22,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 21. "IRQCLRPEND21,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 20. "IRQCLRPEND20,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 19. "IRQCLRPEND19,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 18. "IRQCLRPEND18,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 17. "IRQCLRPEND17,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 16. "IRQCLRPEND16,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 15. "IRQCLRPEND15,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 14. "IRQCLRPEND14,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 13. "IRQCLRPEND13,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 12. "IRQCLRPEND12,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 11. "IRQCLRPEND11,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 10. "IRQCLRPEND10,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 9. "IRQCLRPEND9,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 8. "IRQCLRPEND8,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 7. "IRQCLRPEND7,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 6. "IRQCLRPEND6,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 5. "IRQCLRPEND5,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 4. "IRQCLRPEND4,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 3. "IRQCLRPEND3,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 2. "IRQCLRPEND2,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
newline
|
|
bitfld.long 0x0 1. "IRQCLRPEND1,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
bitfld.long 0x0 0. "IRQCLRPEND0,IRQx interrupt clear pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending on a read.."
|
|
group.long 0x400++0x1F
|
|
line.long 0x0 "NVIC_IPR0,Interrupt Priority"
|
|
hexmask.long.byte 0x0 27.--31. 1. "PRI_N3,IRQx interrupt priority"
|
|
hexmask.long.byte 0x0 19.--23. 1. "PRI_N2,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x0 11.--15. 1. "PRI_N1,IRQx interrupt priority"
|
|
hexmask.long.byte 0x0 3.--7. 1. "PRI_N0,IRQx interrupt priority"
|
|
line.long 0x4 "NVIC_IPR1,Interrupt Priority"
|
|
hexmask.long.byte 0x4 27.--31. 1. "PRI_N7,IRQx interrupt priority"
|
|
hexmask.long.byte 0x4 19.--23. 1. "PRI_N6,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x4 11.--15. 1. "PRI_N5,IRQx interrupt priority"
|
|
hexmask.long.byte 0x4 3.--7. 1. "PRI_N4,IRQx interrupt priority"
|
|
line.long 0x8 "NVIC_IPR2,Interrupt Priority"
|
|
hexmask.long.byte 0x8 27.--31. 1. "PRI_N11,IRQx interrupt priority"
|
|
hexmask.long.byte 0x8 19.--23. 1. "PRI_N10,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x8 11.--15. 1. "PRI_N9,IRQx interrupt priority"
|
|
hexmask.long.byte 0x8 3.--7. 1. "PRI_N8,IRQx interrupt priority"
|
|
line.long 0xC "NVIC_IPR3,Interrupt Priority"
|
|
hexmask.long.byte 0xC 27.--31. 1. "PRI_N15,IRQx interrupt priority"
|
|
hexmask.long.byte 0xC 19.--23. 1. "PRI_N14,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0xC 11.--15. 1. "PRI_N13,IRQx interrupt priority"
|
|
hexmask.long.byte 0xC 3.--7. 1. "PRI_N12,IRQx interrupt priority"
|
|
line.long 0x10 "NVIC_IPR4,Interrupt Priority"
|
|
hexmask.long.byte 0x10 27.--31. 1. "PRI_N19,IRQx interrupt priority"
|
|
hexmask.long.byte 0x10 19.--23. 1. "PRI_N18,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x10 11.--15. 1. "PRI_N17,IRQx interrupt priority"
|
|
hexmask.long.byte 0x10 3.--7. 1. "PRI_N16,IRQx interrupt priority"
|
|
line.long 0x14 "NVIC_IPR5,Interrupt Priority"
|
|
hexmask.long.byte 0x14 27.--31. 1. "PRI_N23,IRQx interrupt priority"
|
|
hexmask.long.byte 0x14 19.--23. 1. "PRI_N22,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x14 11.--15. 1. "PRI_N21,IRQx interrupt priority"
|
|
hexmask.long.byte 0x14 3.--7. 1. "PRI_N20,IRQx interrupt priority"
|
|
line.long 0x18 "NVIC_IPR6,Interrupt Priority"
|
|
hexmask.long.byte 0x18 27.--31. 1. "PRI_N27,IRQx interrupt priority"
|
|
hexmask.long.byte 0x18 19.--23. 1. "PRI_N26,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x18 11.--15. 1. "PRI_N25,IRQx interrupt priority"
|
|
hexmask.long.byte 0x18 3.--7. 1. "PRI_N24,IRQx interrupt priority"
|
|
line.long 0x1C "NVIC_IPR7,Interrupt Priority"
|
|
hexmask.long.byte 0x1C 27.--31. 1. "PRI_N31,IRQx interrupt priority"
|
|
hexmask.long.byte 0x1C 19.--23. 1. "PRI_N30,IRQx interrupt priority"
|
|
newline
|
|
hexmask.long.byte 0x1C 11.--15. 1. "PRI_N29,IRQx interrupt priority"
|
|
hexmask.long.byte 0x1C 3.--7. 1. "PRI_N28,IRQx interrupt priority"
|
|
group.long 0x100++0x3
|
|
line.long 0x0 "NVIC_ISER,Interrupt Set-Enable"
|
|
bitfld.long 0x0 31. "IRQEN31,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 30. "IRQEN30,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 29. "IRQEN29,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 28. "IRQEN28,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 27. "IRQEN27,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 26. "IRQEN26,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 25. "IRQEN25,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 24. "IRQEN24,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 23. "IRQEN23,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 22. "IRQEN22,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 21. "IRQEN21,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 20. "IRQEN20,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 19. "IRQEN19,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 18. "IRQEN18,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 17. "IRQEN17,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 16. "IRQEN16,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 15. "IRQEN15,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 14. "IRQEN14,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 13. "IRQEN13,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 12. "IRQEN12,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 11. "IRQEN11,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 10. "IRQEN10,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 9. "IRQEN9,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 8. "IRQEN8,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 7. "IRQEN7,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 6. "IRQEN6,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 5. "IRQEN5,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 4. "IRQEN4,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 3. "IRQEN3,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 2. "IRQEN2,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
newline
|
|
bitfld.long 0x0 1. "IRQEN1,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
bitfld.long 0x0 0. "IRQEN0,IRQx interrupt set enable" "0: no effect on write,1: enables the associated interrupt"
|
|
group.long 0x200++0x3
|
|
line.long 0x0 "NVIC_ISPR,Interrupt Set-Pending"
|
|
bitfld.long 0x0 31. "IRQSETPEND31,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 30. "IRQSETPEND30,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 29. "IRQSETPEND29,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 28. "IRQSETPEND28,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 27. "IRQSETPEND27,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 26. "IRQSETPEND26,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 25. "IRQSETPEND25,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 24. "IRQSETPEND24,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 23. "IRQSETPEND23,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 22. "IRQSETPEND22,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 21. "IRQSETPEND21,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 20. "IRQSETPEND20,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 19. "IRQSETPEND19,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 18. "IRQSETPEND18,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 17. "IRQSETPEND17,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 16. "IRQSETPEND16,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 15. "IRQSETPEND15,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 14. "IRQSETPEND14,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 13. "IRQSETPEND13,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 12. "IRQSETPEND12,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 11. "IRQSETPEND11,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 10. "IRQSETPEND10,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 9. "IRQSETPEND9,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 8. "IRQSETPEND8,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 7. "IRQSETPEND7,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 6. "IRQSETPEND6,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 5. "IRQSETPEND5,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 4. "IRQSETPEND4,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 3. "IRQSETPEND3,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 2. "IRQSETPEND2,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
newline
|
|
bitfld.long 0x0 1. "IRQSETPEND1,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
bitfld.long 0x0 0. "IRQSETPEND0,IRQx interrupt set pending" "0: the associated interrupt is not pending on a..,1: the associated interrupt is pending"
|
|
group.long 0xD10++0x3
|
|
line.long 0x0 "SCR,System Control Register"
|
|
bitfld.long 0x0 4. "SEVONPEND,Send event on pending" "0: only enabled interrupts or events can wake-up..,1: enabled events and all interrupts including.."
|
|
bitfld.long 0x0 2. "SLEEPDEEP,Selection of sleep mode or deep sleep mode as low power mode" "0: selected sleep mode is sleep,1: selected sleep mode is deep sleep"
|
|
newline
|
|
bitfld.long 0x0 1. "SLEEPONEXIT,Sleep on exit when returning from Handler mode to Thread mode" "0: do not enter sleep mode,1: enter sleep mode. In this case an interrupt.."
|
|
group.long 0xD24++0x3
|
|
line.long 0x0 "SHCSR,System Handler Control and State Register"
|
|
bitfld.long 0x0 18. "USGFAULTENA,UsageFault enable" "0: Disable UsageFault,1: Enable UsageFault"
|
|
bitfld.long 0x0 17. "BUSFAULTENA,BusFault enable" "0: Disable BusFault,1: Enable BusFault"
|
|
newline
|
|
bitfld.long 0x0 16. "MEMFAULTENA,MemManage enable" "0: Disable MemManage fault,1: Enable MemManage fault"
|
|
bitfld.long 0x0 15. "SVCALLPENDED,SVCall exception pending status" "0: SVCall is not pending,1: SVCall is pending"
|
|
newline
|
|
bitfld.long 0x0 14. "BUSFAULTPENDED,BusFault exception pending status" "0: BusFault is not pending,1: BusFault is pending"
|
|
bitfld.long 0x0 13. "MEMFAULTPENDED,MemManage exception pending status" "0: MemManage is not pending,1: MemManage is pending"
|
|
newline
|
|
bitfld.long 0x0 12. "USGFAULTPENDED,UsageFault exception pending status" "0: UsageFault is not pending,1: UsageFault is pending"
|
|
bitfld.long 0x0 11. "SYSTICKACT,SysTick exception status" "0: SysTick is not active,1: SysTick is active"
|
|
newline
|
|
bitfld.long 0x0 10. "PENDSVACT,PendSV exception status" "0: PendSV is not active,1: PendSV is active"
|
|
bitfld.long 0x0 8. "MONITORACT,Debug monitor status" "0: Monitor is not active,1: Monitor is active"
|
|
newline
|
|
bitfld.long 0x0 7. "SVCALLACT,SVCall status" "0: SVCall is not active,1: SVCall is active"
|
|
bitfld.long 0x0 3. "USGFAULTACT,UsageFault exception status" "0: UsageFault is not active,1: UsageFault is active"
|
|
newline
|
|
bitfld.long 0x0 1. "BUSFAULTACT,BusFault exception status" "0: BusFault is not active,1: BusFault is active"
|
|
bitfld.long 0x0 0. "MEMFAULTACT,MemManage exception status" "0: MemManage is not active,1: MemManage is active"
|
|
group.long 0xD18++0xB
|
|
line.long 0x0 "SHPR1,System Handler Priority Register 1"
|
|
hexmask.long.byte 0x0 27.--31. 1. "PRI_7,Reserved for Priority of System Handler 7"
|
|
hexmask.long.byte 0x0 19.--23. 1. "PRI_6,Priority of System Handler 6 UsageFault"
|
|
newline
|
|
hexmask.long.byte 0x0 11.--15. 1. "PRI_5,Priority of System Handler 5 BusFault"
|
|
hexmask.long.byte 0x0 3.--7. 1. "PRI_4,Priority of System Handler 4 MemManage"
|
|
line.long 0x4 "SHPR2,System Handler Priority Register 2"
|
|
hexmask.long.byte 0x4 27.--31. 1. "PRI_11,Priority of System Handler 11 SVCall"
|
|
hexmask.long.byte 0x4 19.--23. 1. "PRI_10,Reserved for Priority of System Handler 10"
|
|
newline
|
|
hexmask.long.byte 0x4 11.--15. 1. "PRI_9,Reserved for Priority of System Handler 9"
|
|
hexmask.long.byte 0x4 3.--7. 1. "PRI_8,Reserved for Priority of System Handler 8"
|
|
line.long 0x8 "SHPR3,System Handler Priority Register 3"
|
|
hexmask.long.byte 0x8 27.--31. 1. "PRI_15,Priority of System Handler 15 SysTick"
|
|
hexmask.long.byte 0x8 19.--23. 1. "PRI_14,Priority of System Handler 14 PendSV"
|
|
newline
|
|
hexmask.long.byte 0x8 11.--15. 1. "PRI_13,Reserved for Priority of System Handler 13"
|
|
hexmask.long.byte 0x8 3.--7. 1. "PRI_12,Priority of System Handler 12 DebugMonitor"
|
|
wgroup.long 0xF00++0x3
|
|
line.long 0x0 "STIR,Software Triggered Interrupt"
|
|
hexmask.long.word 0x0 0.--8. 1. "INTID,Interrupt ID to be triggered. The value written is (ExceptionNumber - 16)"
|
|
rgroup.long 0x1C++0x3
|
|
line.long 0x0 "SYSTICK_CAL,SysTick Calibration Value"
|
|
bitfld.long 0x0 31. "NOREF,Presence of a reference clock" "0: a reference clock is provided,1: no reference clock is provided"
|
|
bitfld.long 0x0 30. "SKEW,Skew" "0: 10ms calibration value is exact,1: 10ms calibration value is inexact because of the.."
|
|
newline
|
|
hexmask.long.tbyte 0x0 0.--23. 1. "TENMS,Reload value used for 10 ms timing"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "SYSTICK_CS,SysTick Control and Status"
|
|
rbitfld.long 0x0 16. "COUNTFLAG,Count Flag" "0: No count to 0 since last read of the register,1: The SysTick timer counted to 0 since the last.."
|
|
bitfld.long 0x0 2. "CLKSOURCE,CLK SysTick timer clock source selection" "0: external reference clock,1: CPU clock"
|
|
newline
|
|
bitfld.long 0x0 1. "TICKINT,TICKINT" "0: counting down to 0 does not assert the SysTick..,1: counting down to 0 asserts the SysTick exeption.."
|
|
bitfld.long 0x0 0. "ENABLE,SysTick counter enable" "0: counter disabled.,1: the counter operates in a multi-shot way. The.."
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "SYSTICK_CUR,SysTick Current Value"
|
|
hexmask.long.tbyte 0x0 0.--23. 1. "CURRENT,Current value of SysTick"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "SYSTICK_RL,SysTick Reload Value"
|
|
hexmask.long.tbyte 0x0 0.--23. 1. "RELOAD,Reload value for SysTick"
|
|
group.long 0xD08++0x3
|
|
line.long 0x0 "VTOR,Vector Table Offset Register"
|
|
hexmask.long 0x0 7.--31. 1. "TBLOFF,Vector Table Offset"
|
|
tree.end
|
|
tree "CSACSC (CSA and CSC)"
|
|
base ad:0x40010000
|
|
group.long 0x0++0x7
|
|
line.long 0x0 "CTRL1,Current sense amplifier and comparator control"
|
|
hexmask.long.word 0x0 16.--25. 1. "THR_MAX,Current sense comparator maximum threshold setting"
|
|
hexmask.long.byte 0x0 12.--15. 1. "OFFS_MIN,Current sense amplifier minimum output offset setting"
|
|
newline
|
|
hexmask.long.byte 0x0 8.--11. 1. "GAIN_MIN,Current sense amplifier minimum gain setting"
|
|
bitfld.long 0x0 0. "CSAC_EN,Current sense amplifier and comparator enable" "0: DISABLE,1: ENABLE"
|
|
line.long 0x4 "CTRL2,Current sense amplifier and comparator control"
|
|
bitfld.long 0x4 24.--25. "TFILT_SEL,Filter time for current sense comparator" "0: 2 us filter time,1: 4 us filter time,2: 6 us filter time,3: 8 us filter time"
|
|
hexmask.long.byte 0x4 16.--20. 1. "THR_SEL,Current sense comparator threshold setting"
|
|
newline
|
|
bitfld.long 0x4 8. "VOUT_SEL,Current sense output selection" "0: CSA output selected,1: Offset voltage selected"
|
|
bitfld.long 0x4 3.--4. "OFFS_SEL,Current sense amplifier output offset setting" "0: Output offset 0.5 V,1: Output offset 1.0 V,2: Output offset 1.5 V,3: Output offset 2.0 V"
|
|
newline
|
|
bitfld.long 0x4 1.--2. "GAIN_SEL,Current sense amplifier gain setting" "0: Gain factor 10,1: Gain factor 20,2: Gain factor 40,3: Gain factor 60"
|
|
bitfld.long 0x4 0. "ADD_INP_OFFS,Additional input offset setting" "0: No offset normal operation,1: +20 mV artificial input offset added"
|
|
wgroup.long 0xC++0x3
|
|
line.long 0x0 "IRQCLR,Current sense amplifier/comparator interrupt status clear"
|
|
bitfld.long 0x0 16. "CSC_OC_SC,Overcurrent event status clear" "0: KEEP,1: CLEAR"
|
|
bitfld.long 0x0 1. "SEL_ERR_ISC,CSA minimum gain or offset selection error interrupt status clear" "0: KEEP,1: CLEAR"
|
|
newline
|
|
bitfld.long 0x0 0. "CSC_OC_ISC,Overcurrent event interrupt status clear" "0: KEEP,1: CLEAR"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "IRQEN,Current sense amplifier/comparator interrupt enable"
|
|
bitfld.long 0x0 1. "SEL_ERR_IEN,CSA minimum gain or offset selection error interrupt enable" "0: DISABLE,1: ENABLE"
|
|
bitfld.long 0x0 0. "CSC_OC_IEN,Overcurrent event interrupt enable" "0: DISABLE,1: ENABLE"
|
|
rgroup.long 0x8++0x3
|
|
line.long 0x0 "IRQS,Current sense amplifier/comparator interrupt status"
|
|
bitfld.long 0x0 25. "CSC_BIST_STS,CSC built-in self test status" "0: CSC built-in self test not started still running..,1: CSC built-in self test successfully completed"
|
|
bitfld.long 0x0 24. "CSC_OC_OUT,Overcurrent comparator output" "0: CSC output is low,1: CSC output is high"
|
|
newline
|
|
bitfld.long 0x0 16. "CSC_OC_STS,Overcurrent event status" "0: No overcurrent event detected,1: Overcurrent event detected"
|
|
bitfld.long 0x0 1. "SEL_ERR_IS,CSA minimum gain or offset selection error interrupt status" "0: CSA min. gain or max. offset selection fulfilled,1: CSA min. gain or max. offset selection violated"
|
|
newline
|
|
bitfld.long 0x0 0. "CSC_OC_IS,Overcurrent event interrupt status" "0: No overcurrent event detected,1: Overcurrent event detected"
|
|
wgroup.long 0x10++0x3
|
|
line.long 0x0 "IRQSET,Current sense amplifier/comparator interrupt status set"
|
|
bitfld.long 0x0 16. "CSC_OC_SS,Overcurrent event status set" "0: KEEP,1: SET"
|
|
bitfld.long 0x0 1. "SEL_ERR_ISS,CSA minimum gain or offset selection error interrupt status set" "0: KEEP,1: SET"
|
|
newline
|
|
bitfld.long 0x0 0. "CSC_OC_ISS,Overcurrent event interrupt status set" "0: KEEP,1: SET"
|
|
tree.end
|
|
tree "DMA (Direct Memory Access)"
|
|
base ad:0x48034000
|
|
rgroup.long 0xC++0x3
|
|
line.long 0x0 "ALT_CTRL_BASE_PTR,Channel Alternate Control Data Base Pointer Register"
|
|
hexmask.long 0x0 0.--31. 1. "ALT_CTRL_BASE_PTR,Base Address of the Alternate Data Structure"
|
|
wgroup.long 0x2C++0x3
|
|
line.long 0x0 "CHNL_ENABLE_CLR,Channel Enable Clear Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_ENABLE_CLR,Channel Enable Clear"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "CHNL_ENABLE_SET,Channel Enable Set Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_ENABLE_SET,Channel Enable Set"
|
|
wgroup.long 0x3C++0x3
|
|
line.long 0x0 "CHNL_PRIORITY_CLR,Channel Priority Clear Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_PRIORITY_CLR,Channel Priority Clear"
|
|
group.long 0x38++0x3
|
|
line.long 0x0 "CHNL_PRIORITY_SET,Channel Priority Set Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_PRIORITY_SET,Channel Priority Set"
|
|
wgroup.long 0x34++0x3
|
|
line.long 0x0 "CHNL_PRI_ALT_CLR,Channel Primary-Alternate Clear Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_PRI_ALT_CLR,Channel Primary Alternate Clear"
|
|
group.long 0x30++0x3
|
|
line.long 0x0 "CHNL_PRI_ALT_SET,Channel Primary-Alternate Set Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_PRI_ALT_SET,Channel Primary Alternate Set"
|
|
wgroup.long 0x24++0x3
|
|
line.long 0x0 "CHNL_REQ_MASK_CLR,Channel Request Mask Clear Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_REQ_MASK_CLR,Channel Request Mask Clear"
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "CHNL_REQ_MASK_SET,Channel Request Mask Set Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_REQ_MASK_SET,Channel Request Mask Set"
|
|
wgroup.long 0x14++0x3
|
|
line.long 0x0 "CHNL_SW_REQUEST,Channel Software Request Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_SW_REQUEST,Software DMA Request"
|
|
wgroup.long 0x1C++0x3
|
|
line.long 0x0 "CHNL_USEBURST_CLR,Channel Useburst Clear Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_USEBURST_CLR,Channel Useburst Clear"
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "CHNL_USEBURST_SET,Channel Useburst Set Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "CHNL_USEBURST_SET,Channel Useburst Set"
|
|
group.long 0x8++0x3
|
|
line.long 0x0 "CTRL_BASE_PTR,Channel Control Data Base Pointer Register"
|
|
hexmask.long.tbyte 0x0 8.--31. 1. "CTRL_BASE_PTR,Pointer to the base address of the primary data structure"
|
|
wgroup.long 0x4++0x3
|
|
line.long 0x0 "DMA_CFG,DMA Configuration Register"
|
|
bitfld.long 0x0 5.--7. "CHN1_PROT_CTRL,AHB Protection" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 0. "MASTER_ENABLE,DMA Controller Enable" "0: disables the controller,1: enables the controller"
|
|
rgroup.long 0x0++0x3
|
|
line.long 0x0 "DMA_STATUS,DMA Status Register"
|
|
hexmask.long.byte 0x0 16.--20. 1. "CHNLS_MINUS1,Number of DMA Channels"
|
|
hexmask.long.byte 0x0 4.--7. 1. "STATE,Current State of the Control State Machine"
|
|
newline
|
|
bitfld.long 0x0 0. "MASTER_ENABLE,Controller Status Enable" "0: controller is disabled,1: controller is enabled"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "DMA_WAITONREQ_STATUS,Channel Wait on Request Status Register"
|
|
hexmask.long.byte 0x0 0.--7. 1. "DMA_WAITONREQ_STATUS,Channel Wait on Request Status"
|
|
group.long 0x4C++0x3
|
|
line.long 0x0 "ERR_CLR,Bus Error Status and Clear Register"
|
|
bitfld.long 0x0 0. "ERR_CLR,Error Clear" "0: on read: dma_err is LOW. on write: No effect..,1: on read: dma_err is HIGH. on write: Sets dma_err.."
|
|
tree.end
|
|
tree "GPIO (General Purpose Input/Output)"
|
|
base ad:0x48030000
|
|
group.long 0x18++0x7
|
|
line.long 0x0 "P0_ALTSEL0,Port 0 alternate output select 0"
|
|
bitfld.long 0x0 28.--30. "ALTSEL7,Alternate output select" "0: GPIO,1: CCU7.COUT71,2: SDADC.DOUT1,3: SSC1.SCLK,4: MultiCAN.TXDC,5: UART0.TXD,6: GPT12.T6OUT,7: ADC2.CMPUP7"
|
|
bitfld.long 0x0 24.--26. "ALTSEL6,Alternate output select" "0: GPIO,1: CCU7.CC71,2: SDADC.DOUT1,3: SSC0.MRST,4: SSC1.CS3,5: SDADC.CMP0,6: ADC1.CMPUP3,7: SSC0.MTSR"
|
|
newline
|
|
bitfld.long 0x0 20.--22. "ALTSEL5,Alternate output select" "0: GPIO,1: CCU7.COUT70,2: SDADC.DOUT0,3: SSC0.SCLK,4: SDADC.CMP1,?,?,?"
|
|
bitfld.long 0x0 16.--18. "ALTSEL4,Alternate output select" "0: GPIO,1: CCU7.CC70,2: SDADC.DOUT0,3: SSC0.MTSR,4: UART1.TXD,5: GPT12.T3OUT,?,?"
|
|
newline
|
|
bitfld.long 0x0 12.--14. "ALTSEL3,Alternate output select" "0: GPIO,1: SSC0.SCLK,2: BEMFC.PH3_ZC_STS,3: CCU7.COUT70,4: SCU.CLKOUT,5: ADC1.CMPLO3,6: UART0.TXD,7: SDADC.CMP1"
|
|
bitfld.long 0x0 8.--10. "ALTSEL2,Alternate output select" "0: GPIO,1: UART1.TXD,2: GPT12.T3OUT,3: SSC0.MRST,4: SSC1.CS0,5: BEMFC.PH2_ZC_STS,6: CCU7.COUT73,?"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "ALTSEL1,Alternate output select" "0: GPIO,1: UART0.TXD,2: GPT12.T6OUT,3: MultiCAN.TXDC,4: CANTRX.RXD,5: SSC0.MTSR,6: BEMFC.PH1_ZC_STS,7: CCU7.CC72"
|
|
bitfld.long 0x0 0.--2. "ALTSEL0,Alternate output select" "0: GPIO,1: CCU7.CC72,2: T21.EXF2,3: UART0.RXDO,?,?,?,?"
|
|
line.long 0x4 "P0_ALTSEL1,Port 0 alternate output select 1"
|
|
bitfld.long 0x4 8.--10. "ALTSEL10,Alternate output select" "0: GPIO,1: SCU.RESET,2: SSC1.CS1,3: SSC0.CS1,4: ADC1.CMPLO2,5: T20.EXF2,6: CCU7.COUT72,7: ADC2.CMPLO7"
|
|
bitfld.long 0x4 4.--6. "ALTSEL9,Alternate output select" "0: GPIO,1: CCU7.CC72,2: SDADC.MCLK,3: SSC1.MRST,4: SSC0.CS3,5: ADC1.CMPLO0,6: SSC1.MTSR,?"
|
|
newline
|
|
bitfld.long 0x4 0.--2. "ALTSEL8,Alternate output select" "0: GPIO,1: CCU7.COUT72,2: SDADC.MCLK,3: SSC1.MTSR,4: ADC1.CMPLO1,?,?,?"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "P0_DIR,Port 0 direction control"
|
|
bitfld.long 0x0 10. "DIR10,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 9. "DIR9,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 8. "DIR8,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 7. "DIR7,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 6. "DIR6,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 5. "DIR5,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 4. "DIR4,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 3. "DIR3,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 2. "DIR2,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 1. "DIR1,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 0. "DIR0,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
rgroup.long 0x8++0x3
|
|
line.long 0x0 "P0_IN,Port 0 input register"
|
|
bitfld.long 0x0 10. "PI10,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 9. "PI9,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 8. "PI8,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 7. "PI7,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 6. "PI6,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 5. "PI5,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 4. "PI4,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 3. "PI3,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 2. "PI2,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 1. "PI1,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 0. "PI0,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "P0_OD,Port 0 open drain control"
|
|
bitfld.long 0x0 10. "OD10,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 9. "OD9,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 8. "OD8,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 7. "OD7,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 6. "OD6,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 5. "OD5,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 4. "OD4,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 3. "OD3,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 2. "OD2,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 1. "OD1,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 0. "OD0,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
wgroup.long 0x4++0x3
|
|
line.long 0x0 "P0_OMR,Port 0 output modification register"
|
|
bitfld.long 0x0 26. "PR10,Output reset bit" "0,1"
|
|
bitfld.long 0x0 25. "PR9,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 24. "PR8,Output reset bit" "0,1"
|
|
bitfld.long 0x0 23. "PR7,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 22. "PR6,Output reset bit" "0,1"
|
|
bitfld.long 0x0 21. "PR5,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 20. "PR4,Output reset bit" "0,1"
|
|
bitfld.long 0x0 19. "PR3,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 18. "PR2,Output reset bit" "0,1"
|
|
bitfld.long 0x0 17. "PR1,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 16. "PR0,Output reset bit" "0,1"
|
|
bitfld.long 0x0 10. "PS10,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 9. "PS9,Output set bit" "0,1"
|
|
bitfld.long 0x0 8. "PS8,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 7. "PS7,Output set bit" "0,1"
|
|
bitfld.long 0x0 6. "PS6,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 5. "PS5,Output set bit" "0,1"
|
|
bitfld.long 0x0 4. "PS4,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "PS3,Output set bit" "0,1"
|
|
bitfld.long 0x0 2. "PS2,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 1. "PS1,Output set bit" "0,1"
|
|
bitfld.long 0x0 0. "PS0,Output set bit" "0,1"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "P0_OUT,Port 0 output register"
|
|
bitfld.long 0x0 10. "PO10,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 9. "PO9,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 8. "PO8,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 7. "PO7,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 6. "PO6,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 5. "PO5,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 4. "PO4,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 3. "PO3,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 2. "PO2,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 1. "PO1,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 0. "PO0,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "P0_POCON,Port 0 output driver control"
|
|
bitfld.long 0x0 20.--21. "PDM10,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 18.--19. "PDM9,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 16.--17. "PDM8,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 14.--15. "PDM7,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "PDM6,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 10.--11. "PDM5,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 8.--9. "PDM4,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 6.--7. "PDM3,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "PDM2,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 2.--3. "PDM1,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "PDM0,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "P0_PUD,Port 0 pull-up/pull-down control"
|
|
bitfld.long 0x0 26. "PUDSEL10,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 25. "PUDSEL9,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 24. "PUDSEL8,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 23. "PUDSEL7,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 22. "PUDSEL6,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 21. "PUDSEL5,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 20. "PUDSEL4,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 19. "PUDSEL3,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 18. "PUDSEL2,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 17. "PUDSEL1,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 16. "PUDSEL0,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 10. "PUDEN10,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 9. "PUDEN9,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 8. "PUDEN8,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 7. "PUDEN7,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 6. "PUDEN6,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 5. "PUDEN5,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 4. "PUDEN4,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "PUDEN3,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 2. "PUDEN2,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "PUDEN1,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 0. "PUDEN0,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
group.long 0x3C++0x3
|
|
line.long 0x0 "P1_ALTSEL0,Port 1 alternate output select 0"
|
|
bitfld.long 0x0 16.--18. "ALTSEL4,Alternate output select" "0: GPIO,1: SSC1.CS2,2: SCU.CLKOUT,3: BEMFC.PH2_ZC_STS,4: T21.EXF2,?,?,?"
|
|
bitfld.long 0x0 12.--14. "ALTSEL3,Alternate output select" "0: GPIO,1: SSC0.CS2,2: CCU7.COUT73,3: MultiCAN.TXDC,4: UART0.TXD,5: GPT12.T6OUT,6: BEMFC.PH1_ZC_STS,?"
|
|
newline
|
|
bitfld.long 0x0 8.--10. "ALTSEL2,Alternate output select" "0: GPIO,1: SSC1.MRST,2: CCU7.CC70,3: SSC0.CS0,4: SCU.CLKOUT,5: BEMFC.PH3_ZC_STS,6: ADC1.CMPUP0,7: SSC1.MTSR"
|
|
bitfld.long 0x0 4.--6. "ALTSEL1,Alternate output select" "0: GPIO,1: SSC1.MTSR,2: CCU7.COUT71,3: UART1.TXD,4: GPT12.T3OUT,5: CANTRX.RXD,6: ADC1.CMPUP1,7: ADC2.CMPUP6"
|
|
newline
|
|
bitfld.long 0x0 0.--2. "ALTSEL0,Alternate output select" "0: GPIO,1: SSC1.SCLK,2: CCU7.CC71,3: GPT12.T6OUT,4: UART1.RXDO,5: ADC1.CMPUP2,6: SDADC.CMP0,7: ADC2.CMPLO6"
|
|
group.long 0x30++0x3
|
|
line.long 0x0 "P1_DIR,Port 1 direction control"
|
|
bitfld.long 0x0 4. "DIR4,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 3. "DIR3,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 2. "DIR2,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
bitfld.long 0x0 1. "DIR1,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
newline
|
|
bitfld.long 0x0 0. "DIR0,Direction control bit" "0: Pin direction is input,1: Pin direction is output"
|
|
rgroup.long 0x2C++0x3
|
|
line.long 0x0 "P1_IN,Port 1 input register"
|
|
bitfld.long 0x0 4. "PI4,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 3. "PI3,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 2. "PI2,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 1. "PI1,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 0. "PI0,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
group.long 0x34++0x3
|
|
line.long 0x0 "P1_OD,Port 1 open drain control"
|
|
bitfld.long 0x0 4. "OD4,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 3. "OD3,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 2. "OD2,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
bitfld.long 0x0 1. "OD1,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
newline
|
|
bitfld.long 0x0 0. "OD0,Open drain control bit" "0: Push-pull driver for active 0 and 1 state,1: Open drain driver for active 0 state only"
|
|
wgroup.long 0x28++0x3
|
|
line.long 0x0 "P1_OMR,Port 1 output modification register"
|
|
bitfld.long 0x0 20. "PR4,Output reset bit" "0,1"
|
|
bitfld.long 0x0 19. "PR3,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 18. "PR2,Output reset bit" "0,1"
|
|
bitfld.long 0x0 17. "PR1,Output reset bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 16. "PR0,Output reset bit" "0,1"
|
|
bitfld.long 0x0 4. "PS4,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "PS3,Output set bit" "0,1"
|
|
bitfld.long 0x0 2. "PS2,Output set bit" "0,1"
|
|
newline
|
|
bitfld.long 0x0 1. "PS1,Output set bit" "0,1"
|
|
bitfld.long 0x0 0. "PS0,Output set bit" "0,1"
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "P1_OUT,Port 1 output register"
|
|
bitfld.long 0x0 4. "PO4,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 3. "PO3,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 2. "PO2,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
bitfld.long 0x0 1. "PO1,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
newline
|
|
bitfld.long 0x0 0. "PO0,Output bit" "0: Output value = 0,1: Output value = 1"
|
|
group.long 0x40++0x3
|
|
line.long 0x0 "P1_POCON,Port 1 output driver control"
|
|
bitfld.long 0x0 8.--9. "PDM4,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 6.--7. "PDM3,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "PDM2,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
bitfld.long 0x0 2.--3. "PDM1,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "PDM0,Output driver mode control" "0: Strong driver and sharp edge,1: Strong driver and medium edge,2: Medium driver,3: Weak driver"
|
|
group.long 0x38++0x3
|
|
line.long 0x0 "P1_PUD,Port 1 pull-up/pull-down control"
|
|
bitfld.long 0x0 20. "PUDSEL4,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 19. "PUDSEL3,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 18. "PUDSEL2,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 17. "PUDSEL1,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x0 16. "PUDSEL0,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x0 4. "PUDEN4,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "PUDEN3,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 2. "PUDEN2,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "PUDEN1,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x0 0. "PUDEN0,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
rgroup.long 0x44++0x3
|
|
line.long 0x0 "P2_IN,Port 2 input register"
|
|
bitfld.long 0x0 9. "PI9,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 8. "PI8,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 7. "PI7,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 6. "PI6,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 5. "PI5,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 4. "PI4,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 3. "PI3,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 2. "PI2,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
newline
|
|
bitfld.long 0x0 1. "PI1,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
bitfld.long 0x0 0. "PI0,Input bit" "0: Input value = 0,1: Input value = 1"
|
|
group.long 0x48++0x7
|
|
line.long 0x0 "P2_INDIS,Port 2 input disable register"
|
|
bitfld.long 0x0 9. "INDIS9,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
bitfld.long 0x0 8. "INDIS8,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
newline
|
|
bitfld.long 0x0 7. "INDIS7,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
bitfld.long 0x0 6. "INDIS6,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
newline
|
|
bitfld.long 0x0 5. "INDIS5,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
bitfld.long 0x0 4. "INDIS4,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
newline
|
|
bitfld.long 0x0 3. "INDIS3,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
bitfld.long 0x0 2. "INDIS2,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
newline
|
|
bitfld.long 0x0 1. "INDIS1,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
bitfld.long 0x0 0. "INDIS0,Input disable control bit" "0: Digital input receiver is enabled,1: Digital input receiver is disabled no.."
|
|
line.long 0x4 "P2_PUD,Port 2 pull-up/pull-down control"
|
|
bitfld.long 0x4 25. "PUDSEL9,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x4 24. "PUDSEL8,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x4 23. "PUDSEL7,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x4 22. "PUDSEL6,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x4 21. "PUDSEL5,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x4 20. "PUDSEL4,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x4 19. "PUDSEL3,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x4 18. "PUDSEL2,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x4 17. "PUDSEL1,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
bitfld.long 0x4 16. "PUDSEL0,Pull-up/pull-down select bit" "0: Pull-down device is selected,1: Pull-up device is selected"
|
|
newline
|
|
bitfld.long 0x4 9. "PUDEN9,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x4 8. "PUDEN8,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x4 7. "PUDEN7,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x4 6. "PUDEN6,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x4 5. "PUDEN5,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x4 4. "PUDEN4,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x4 3. "PUDEN3,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x4 2. "PUDEN2,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "PUDEN1,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
bitfld.long 0x4 0. "PUDEN0,Pull-up/pull-down enable bit" "0: Pull-up/pull-down devices are disabled,1: Pull-up or pull-down device is enabled"
|
|
tree.end
|
|
tree "GPT12 (General Purpose Timer Units)"
|
|
base ad:0x40014000
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "CAPREL,Capture/Reload Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "CAPREL,Current reload value or Captured value"
|
|
rgroup.long 0x0++0x3
|
|
line.long 0x0 "ID,Module Identification Register"
|
|
hexmask.long.byte 0x0 8.--15. 1. "MOD_TYPE,Module Identification Number"
|
|
hexmask.long.byte 0x0 0.--7. 1. "MOD_REV,Module Revision Number"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "PISEL,Port Input Select Register"
|
|
bitfld.long 0x0 14.--15. "ISCAPIN,Input Select for CAPIN" "0: Signal CAPINA is selected,1: Signal CAPINB is selected,2: Signal CAPINC (Read trigger from T3) is selected,3: Signal CAPIND (Read trigger from T2 or T3 or T4).."
|
|
bitfld.long 0x0 13. "IST6EUD,Input Select for T6EUD" "0: Signal T6EUDA is selected,1: Signal T6EUDB is selected"
|
|
newline
|
|
bitfld.long 0x0 12. "IST6IN,Input Select for T6IN" "0: Signal T6INA is selected,1: Signal T6INB is selected"
|
|
bitfld.long 0x0 11. "IST5EUD,Input Select for T5EUD" "0: Signal T5EUDA is selected,1: Signal T5EUDB is selected"
|
|
newline
|
|
bitfld.long 0x0 10. "IST5IN,Input Select for T5IN" "0: Signal T5INA is selected,1: Signal T5INB is selected"
|
|
bitfld.long 0x0 8.--9. "IST4EUD,Input Select for TEUD" "0: Signal T4EUDA is selected,1: Signal T4EUDB is selected,2: Signal T4EUDC is selected,3: Signal T4EUDD is selected"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "IST4IN,Input Select for T4IN" "0: Signal T4INA is selected,1: Signal T4INB is selected,2: Signal T4INC is selected,3: Signal T4IND is selected"
|
|
bitfld.long 0x0 4.--5. "IST3EUD,Input Select for T3EUD" "0: Signal T3EUDA is selected,1: Signal T3EUDB is selected,2: Signal T3EUDC is selected,3: Signal T3EUDD is selected"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "IST3IN,Input Select for T3IN" "0: Signal T3INA is selected,1: Signal T3INB is selected,2: Signal T3INC is selected,3: Signal T3IND is selected"
|
|
bitfld.long 0x0 1. "IST2EUD,Input Select for T2EUD" "0: Signal T2EUDA is selected,1: Signal T2EUDB is selected"
|
|
newline
|
|
bitfld.long 0x0 0. "IST2IN,Input Select for T2IN" "0: Signal T2INA is selected,1: Signal T2INB is selected"
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "T2,Timer T2 Count Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T2,Timer T2 Current Value"
|
|
group.long 0x8++0x3
|
|
line.long 0x0 "T2CON,Timer T2 Control Register"
|
|
rbitfld.long 0x0 15. "T2DIR,Timer T2 Rotation Direction" "0: Timer T2 counts up,1: Timer T2 counts down"
|
|
bitfld.long 0x0 14. "T2CHDIR,Timer T2 Count Direction Change" "0: No change of count direction was detected,1: A change of count direction was detected"
|
|
newline
|
|
bitfld.long 0x0 13. "T2EDGE,Timer T2 Edge Detection" "0: No count edge was detected,1: A count edge was detected"
|
|
bitfld.long 0x0 12. "T2IRIDIS,Timer T2 Interrupt Disable" "0: Interrupt generation for T2CHDIR and T2EDGE..,1: Interrupt generation for T2CHDIR and T2EDGE.."
|
|
newline
|
|
bitfld.long 0x0 9. "T2RC,Timer T2 Remote Control" "0: Timer T2 is controlled by its own run bit T2R,1: Timer T2 is controlled by the run bit T3R of.."
|
|
bitfld.long 0x0 8. "T2UDE,Timer T2 External Up/Down Enable" "0: Count direction is controlled by bit T2UD; input..,1: Count direction is controlled by input T2EUD"
|
|
newline
|
|
bitfld.long 0x0 7. "T2UD,Timer T2 Up/Down Control" "0: Timer T2 counts up,1: Timer T2 counts down"
|
|
bitfld.long 0x0 6. "T2R,Timer T2 Input Run Bit" "0: Timer T2 stops,1: Timer T2 runs"
|
|
newline
|
|
bitfld.long 0x0 3.--5. "T2M,Timer T2 Input Mode Control" "0: TimerMode,1: CounterMode,2: Gated Timer Mode with gate active low,3: Gated Timer Mode with gate active high,4: ReloadMode,5: CaptureMode,6: (Rotation Detection Mode),7: (Edge Detection Mode)"
|
|
bitfld.long 0x0 0.--2. "T2I,Timer T2 Input Parameter Selection" "0,1,2,3,4,5,6,7"
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "T3,Timer T3 Count Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T3,Timer T3 Current Value"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "T3CON,Timer T3 Control Register"
|
|
rbitfld.long 0x0 15. "T3DIR,Timer T3 Rotation Direction Flag" "0: Timer T3 counts up,1: Timer T3 counts down"
|
|
bitfld.long 0x0 14. "T3CHDIR,Timer T3 Count Direction Change Flag" "0: No change of count direction was detected,1: A change of count direction was detected"
|
|
newline
|
|
bitfld.long 0x0 13. "T3EDGE,Timer T3 Edge Detection Flag" "0: No count edge was detected,1: A count edge was detected"
|
|
bitfld.long 0x0 11.--12. "BPS1,GPT1 Block Prescaler Control" "0: GPT_CLK/8,1: GPT_CLK/4,2: GPT_CLK/32,3: GPT_CLK/16"
|
|
newline
|
|
bitfld.long 0x0 10. "T3OTL,Timer T3 Overflow Toggle Latch" "0,1"
|
|
bitfld.long 0x0 9. "T3OE,Overflow/Underflow Output Enable" "0: Alternate Output Function Disabled,1: State of T3 toggle latch is output on pin T3OUT"
|
|
newline
|
|
bitfld.long 0x0 8. "T3UDE,Timer T3 External Up/Down Enable" "0: Count direction is controlled by bit T3UD; input..,1: Count direction is controlled by input T3EUD"
|
|
bitfld.long 0x0 7. "T3UD,Timer T3 Up/Down Control" "0: Timer T3 counts up,1: Timer T3 counts down"
|
|
newline
|
|
bitfld.long 0x0 6. "T3R,Timer T3 Input Run Bit" "0: Timer T3 stops,1: Timer T3 runs"
|
|
bitfld.long 0x0 3.--5. "T3M,Timer T3 Input Mode Control" "0: TimerMode,1: CounterMode,2: Gated Timer Mode with gate active low,3: Gated Timer Mode with gate active high,?,?,6: (Rotation Detection Mode),7: (Edge Detection Mode)"
|
|
newline
|
|
bitfld.long 0x0 0.--2. "T3I,Timer T3 Input Parameter Selection" "0,1,2,3,4,5,6,7"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "T4,Timer T4 Count Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T4,Timer T4 Current Value"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "T4CON,Timer T4 Control Register"
|
|
rbitfld.long 0x0 15. "T4RDIR,Timer T4 Rotation Direction" "0: Timer T4 counts up,1: Timer T4 counts down"
|
|
bitfld.long 0x0 14. "T4CHDIR,Timer T4 Count Direction Change" "0: No change in count direction was detected,1: A change in count direction was detected"
|
|
newline
|
|
bitfld.long 0x0 13. "T4EDGE,Timer T4 Edge Direction" "0: No count edge was detected,1: A count edge was detected"
|
|
bitfld.long 0x0 12. "T4IRDIS,Timer T4 Interrupt Disable" "0: Interrupt generation for T4CHDIR and T4EDGE..,1: Interrupt generation for T4CHDIR and T4EDGE.."
|
|
newline
|
|
bitfld.long 0x0 11. "CLRT3EN,Clear Timer T3 Enable" "0: No effect of T4IN on Timer T3,1: A falling edge on T4In clears timer T3"
|
|
bitfld.long 0x0 10. "CLRT2EN,Clear Timer T2 Enable" "0: No effect of T4EUD on timer T2,1: A falling edge on T4EUD clears timer T2"
|
|
newline
|
|
bitfld.long 0x0 9. "T4RC,Timer T4 Remote Control" "0: Timer T4 is controlled by its own run bit T4R,1: Timer T4 is controlled by the run bit T3R of.."
|
|
bitfld.long 0x0 8. "T4UDE,Timer T4 External Up/Down Enable" "0: Count direction is controlled by bit T4UD; input..,1: Count direction is controlled by input T4EUD"
|
|
newline
|
|
bitfld.long 0x0 7. "T4UD,Timer T4 Up/Down Control" "0: Timer T4 counts up,1: Timer T4 counts down"
|
|
bitfld.long 0x0 6. "T4R,Timer T4 Input Run Bit" "0: Timer T4 stops,1: Timer T4 runs"
|
|
newline
|
|
bitfld.long 0x0 3.--5. "T4M,Timer T4 Mode Control (Basic Operating Mode)" "0: TimerMode,1: CounterMode,2: Gated Timer Mode with gate active low,3: Gated Timer Mode with gate active high,4: ReloadMode,5: CaptureMode,6: (Rotation Detection Mode),7: (Edge Detection Mode)"
|
|
bitfld.long 0x0 0.--2. "T4I,Timer T4 Input Parameter Selection" "0,1,2,3,4,5,6,7"
|
|
group.long 0x2C++0x3
|
|
line.long 0x0 "T5,Timer 5 Count Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T5,Timer T5 Current Value"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "T5CON,Timer T5 Control Register"
|
|
bitfld.long 0x0 15. "T5SC,Timer T5 Capture Mode Enable" "0: Capture into register CAPREL disabled,1: Capture into register CAPREL enabled"
|
|
bitfld.long 0x0 14. "T5CLR,Timer T5 Clear Enable Bit" "0: Timer T5 is not cleared on a capture event,1: Timer T5 is cleared on a capture event"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "CI,Register CAPREL Capture Trigger Selection" "0: Capture disabled,1: Positive transition (rising edge) on CAPIN,2: Negative transition (falling edge) on CAPIN or..,3: Any transition (rising or falling edge) on CAPIN.."
|
|
bitfld.long 0x0 10. "CT3,Timer T3 Capture Trigger Enable" "0: Capture trigger from input line CAPIN,1: Capture trigger from T3 input lines T3IN and/or.."
|
|
newline
|
|
bitfld.long 0x0 9. "T5RC,Timer T5 Remote Control" "0: Timer T5 is controlled by its own run bit T5R,1: Timer T5 is controlled by the run bit T6R of.."
|
|
bitfld.long 0x0 8. "T5UDE,Timer T5 External Up/Down Enable" "0: Count direction is controlled by bit T5UD; input..,1: Count direction is controlled by input T5EUD"
|
|
newline
|
|
bitfld.long 0x0 7. "T5UD,Timer T5 Up/Down Control" "0: Timer T5 counts up,1: Timer T5 counts down"
|
|
bitfld.long 0x0 6. "T5R,Timer T5 Run Bit" "0: Timer T5 stops,1: Timer T5 runs"
|
|
newline
|
|
bitfld.long 0x0 3.--4. "T5M,Timer T5 Input Mode Control" "0: TimerMode,1: CounterMode,2: Gated Timer Mode with gate active low,3: Gated Timer Mode with gate active high"
|
|
bitfld.long 0x0 0.--2. "T5I,Timer T5 Input Parameter Selection" "0,1,2,3,4,5,6,7"
|
|
group.long 0x30++0x3
|
|
line.long 0x0 "T6,Timer 6 Count Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "T6,Timer T6 Current Value"
|
|
group.long 0x18++0x3
|
|
line.long 0x0 "T6CON,Timer T6 Control Register"
|
|
bitfld.long 0x0 15. "T6SR,Timer T6 Reload Mode Enable" "0: Reload from register CAPREL disabled,1: Reload from register CAPREL enabled"
|
|
bitfld.long 0x0 14. "T6CLR,Timer T6 Clear Enable Bit" "0: Timer T6 is not cleared on a capture event,1: Timer T6 is cleared on a capture event"
|
|
newline
|
|
bitfld.long 0x0 11.--12. "BPS2,GPT2 Block Prescaler Control" "0: GPT_CLK/4,1: GPT_CLK/2,2: GPT_CLK/16,3: GPT_CLK/8"
|
|
bitfld.long 0x0 10. "T6OTL,Timer T6 Overflow Toggle Latch" "0,1"
|
|
newline
|
|
bitfld.long 0x0 9. "T6OE,Overflow/Underflow Output Enable" "0: Alternate Output Function Disabled,1: State of T6 toggle latch is output on pin T6OUT"
|
|
bitfld.long 0x0 8. "T6UDE,Timer T6 External Up/Down Enable" "0: Count direction is controlled by bit T6UD; input..,1: Count direction is controlled by input T6EUD"
|
|
newline
|
|
bitfld.long 0x0 7. "T6UD,Timer T6 Up/Down Control" "0: Timer T3 counts up,1: Timer T3 counts down"
|
|
bitfld.long 0x0 6. "T6R,Timer T6 Input Run Bit" "0: Timer T3 stops,1: Timer T3 runs"
|
|
newline
|
|
bitfld.long 0x0 3.--5. "T6M,Timer T6 Mode Control" "0: TimerMode,1: CounterMode,2: Gated Timer Mode with gate active low,3: Gated Timer Mode with gate active high,?,?,?,?"
|
|
bitfld.long 0x0 0.--2. "T6I,Timer T6 Input Parameter Selection" "0,1,2,3,4,5,6,7"
|
|
tree.end
|
|
tree "MEMCTRL (Memory Control)"
|
|
base ad:0x48044000
|
|
rgroup.long 0x0++0x3
|
|
line.long 0x0 "BFSTS,Bus Fault Status Register"
|
|
bitfld.long 0x0 1. "SBFSTS,System Bus Fault Status Valid Flag" "0: Fault Address is not valid,1: the address of an occurred System Bus Fault is.."
|
|
bitfld.long 0x0 0. "DBFSTS,Data Bus Fault Status Valid Flag" "0: Fault Address is not valid,1: the address of an occurred Data Bus Fault is.."
|
|
wgroup.long 0x4++0x7
|
|
line.long 0x0 "BFSTSC,Bus Fault Status Clear Register"
|
|
bitfld.long 0x0 1. "SBFSTSCLR,System Bus Fault Status Valid Flag Clear" "0: Fault Address is not cleared,1: Fault Address is cleared"
|
|
bitfld.long 0x0 0. "DBFSTSCLR,Data Bus Fault Status Valid Flag Clear" "0: Fault Address is not cleared,1: Fault Address is cleared"
|
|
line.long 0x4 "BFSTSS,Bus Fault Status Set Register"
|
|
bitfld.long 0x4 1. "SBFSTSSET,System Bus Fault Status Valid Flag Set" "0: Fault Address is not Set,1: Fault Address is Set"
|
|
bitfld.long 0x4 0. "DBFSTSSET,Data Bus Fault Status Valid Flag Set" "0: Fault Address is not Set,1: Fault Address is Set"
|
|
rgroup.long 0xC++0x3
|
|
line.long 0x0 "DBFA,Data Bus Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 1. "DBFA,Data Bus Fault Address"
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "IEN,MEMCTRL Interrupt Enable Register"
|
|
bitfld.long 0x0 1. "NVM1OPCIEN,NVM1 Operation Complete Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 0. "NVM0OPCIEN,NVM0 Operation Complete Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x28++0x3
|
|
line.long 0x0 "IS,MEMCTRL Interrupt Status Register"
|
|
bitfld.long 0x0 1. "NVM1OPC,NVM1 Operation Complete Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "NVM0OPC,NVM0 Operation Complete Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x2C++0x7
|
|
line.long 0x0 "ISC,MEMCTRL Interrupt Status Clear Register"
|
|
bitfld.long 0x0 1. "NVM1OPCLR,NVM1 Operation Complete Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "NVM0OPCLR,NVM0 Operation Complete Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
line.long 0x4 "ISS,MEMCTRL Interrupt Status Set Register"
|
|
bitfld.long 0x4 1. "NVM1OPSET,NVM1 Operation Complete Interrupt Status Set" "0: Interrupt not Set,1: Interrupt Set"
|
|
bitfld.long 0x4 0. "NVM0OPSET,NVM0 Operation Complete Interrupt Status Set" "0: Interrupt not Set,1: Interrupt Set"
|
|
group.long 0xA4++0x3
|
|
line.long 0x0 "MEMSTAT,Memory Status Register"
|
|
bitfld.long 0x0 6.--7. "SASTATUS,Service Algorithm Status" "0: If MEMSTAT.SECTORINFO = 0 the NVM is initialized..,1: The Service Algorithm is successful and more..,2: The Service Algorithm is not successful and map..,3: The NVM initialization has failed. The Service.."
|
|
hexmask.long.byte 0x0 0.--5. 1. "SECTORINFO,Sector number where the Service Algorithm is running\n"
|
|
rgroup.long 0x34++0x3
|
|
line.long 0x0 "MEMSTS,Memory Protection and Error Status Register"
|
|
bitfld.long 0x0 18. "CDSBE,Cache Data RAM Single Bit Error Status" "0: Single Bit Error not occured,1: Single Bit Error occured"
|
|
bitfld.long 0x0 17. "PSSBE,PSRAM Single Bit Error Status" "0: Single Bit Error not occured,1: Single Bit Error occured"
|
|
newline
|
|
bitfld.long 0x0 16. "DSSBE,DSRAM Single Bit Error Status" "0: Single Bit Error not occurred,1: Single Bit Error occurred"
|
|
bitfld.long 0x0 10. "PSRAM_PROT_ERR,PSRAM Access Protection Error" "0: No Protection error,1: Protection error"
|
|
newline
|
|
bitfld.long 0x0 9. "DSRAM_PROT_ERR,DSRAM Access Protection Error" "0: No Protection error,1: Protection error"
|
|
bitfld.long 0x0 8. "ROM_PROT_ERR,ROM Access Protection Error" "0: No Protection error,1: Protection error"
|
|
newline
|
|
bitfld.long 0x0 7. "NVM1_SFR_ADDR_ERR,NVM1 SFR Address Protection Error" "0: No Protection error,1: Protection error"
|
|
bitfld.long 0x0 6. "NVM1_SFR_PROT_ERR,NVM1 SFR Access Protection Error" "0: No Protection error,1: Protection error"
|
|
newline
|
|
bitfld.long 0x0 5. "NVM1_ADDR_ERR,NVM1 Address Protection Error" "0: No Protection error,1: Protection error"
|
|
bitfld.long 0x0 4. "NVM1_PROT_ERR,NVM1 Access Protection Error" "0: No Protection error,1: Protection error"
|
|
newline
|
|
bitfld.long 0x0 3. "NVM0_SFR_ADDR_ERR,NVM0 SFR Address Protection Error" "0: No Protection error,1: Protection error"
|
|
bitfld.long 0x0 2. "NVM0_SFR_PROT_ERR,NVM0 SFR Access Protection Error" "0: No Protection error,1: Protection error"
|
|
newline
|
|
bitfld.long 0x0 1. "NVM0_ADDR_ERR,NVM0 Address Protection Error" "0: No Protection error,1: Protection error"
|
|
bitfld.long 0x0 0. "NVM0_PROT_ERR,NVM0 Access Protection Error" "0: No Protection error,1: Protection error"
|
|
wgroup.long 0x38++0x7
|
|
line.long 0x0 "MEMSTSC,Memory Protection and Error Status Register Clear"
|
|
bitfld.long 0x0 18. "CDSBECLR,Cache Data RAM Single Bit Error Status Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 17. "PSSBECLR,PSRAM Single Bit Error Status Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 16. "DSSBECLR,DSRAM Single Bit Error Status Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 10. "PSRAM_PROT_ERRCLR,PSRAM Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 9. "DSRAM_PROT_ERRCLR,DSRAM Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 8. "ROM_PROT_ERRCLR,ROM Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 7. "NVM1_SFR_ADDR_ERRCLR,NVM1 SFR Address Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 6. "NVM1_SFR_PROT_ERRCLR,NVM1 SFR Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "NVM1_ADDR_ERRCLR,NVM1 Address Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 4. "NVM1_PROT_ERRCLR,NVM1 Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "NVM0_SFR_ADDR_ERRCLR,NVM0 SFR Address Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 2. "NVM0_SFR_PROT_ERRCLR,NVM0 SFR Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "NVM0_ADDR_ERRCLR,NVM0 Address Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
bitfld.long 0x0 0. "NVM0_PROT_ERRCLR,NVM0Access Protection Error Clear" "0: Error not cleared,1: Error cleared"
|
|
line.long 0x4 "MEMSTSS,Memory Protection and Error Status Register Set"
|
|
bitfld.long 0x4 18. "CDSBESET,Cache Data RAM Single Bit Error Status Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 17. "PSSBESET,PSRAM Single Bit Error Status Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 16. "DSSBESET,DSRAM Single Bit Error Status Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 10. "PSRAM_PROT_ERRSET,PSRAM Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 9. "DSRAM_PROT_ERRSET,DSRAM Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 8. "ROM_PROT_ERRSET,ROM Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 7. "NVM1_SFR_ADDR_ERRSET,NVM1 SFR Address Protection Error Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 6. "NVM1_SFR_PROT_ERRSET,NVM1 SFR Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 5. "NVM1_ADDR_ERRSET,NVM1 Address Protection Error Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 4. "NVM1_PROT_ERRSET,NVM1 Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 3. "NVM0_SFR_ADDR_ERRSET,NVM0 SFR Address Protection Error Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 2. "NVM0_SFR_PROT_ERRSET,NVM0 SFR Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
newline
|
|
bitfld.long 0x4 1. "NVM0_ADDR_ERRSET,NVM0 Address Protection Error Set" "0: Error not Set,1: Error Set"
|
|
bitfld.long 0x4 0. "NVM0_PROT_ERRSET,NVM0 Access Protection Error Set" "0: Error not Set,1: Error Set"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "NMICON,NMI Control Register"
|
|
bitfld.long 0x0 8. "NMISTOFEN,Stack Overflow NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
bitfld.long 0x0 7. "NMIWDTEN,Watchdog Timer NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
newline
|
|
bitfld.long 0x0 6. "NMIMAP1EN,NVM1 MAP Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
bitfld.long 0x0 5. "NMIMAP0EN,NVM0 MAP Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "NMINVM1EN,NVM1 Double Bit ECC Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
bitfld.long 0x0 3. "NMINVM0EN,NVM0 Double Bit ECC Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "NMICDEN,Cache Data RAM Double Bit ECC Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
bitfld.long 0x0 1. "NMIPSEN,PSRAM Double Bit ECC Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIDSEN,DSRAM Double Bit ECC Error NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
rgroup.long 0x18++0x3
|
|
line.long 0x0 "NMISR,NMI Status Register"
|
|
bitfld.long 0x0 8. "NMISTOF,Stack Overflow NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
bitfld.long 0x0 7. "NMIWDT,Watchdog Timer NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
newline
|
|
bitfld.long 0x0 6. "NMIMAP1,NVM1 MAP Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
bitfld.long 0x0 5. "NMIMAP0,NVM0 MAP Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
newline
|
|
bitfld.long 0x0 4. "NMINVM1,NVM1 Double Bit ECC Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
bitfld.long 0x0 3. "NMINVM0,NVM0 Double Bit ECC Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
newline
|
|
bitfld.long 0x0 2. "NMICD,Cache Data RAM Double Bit ECC Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
bitfld.long 0x0 1. "NMIPS,PSRAM Double Bit ECC Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIDS,DSRAM Double Bit ECC Error NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
wgroup.long 0x1C++0x7
|
|
line.long 0x0 "NMISRC,NMI Status Clear Register"
|
|
bitfld.long 0x0 8. "NMISTOFCLR,Stack Overflow NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
bitfld.long 0x0 7. "NMIWDTCLR,Watchdog Timer NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
newline
|
|
bitfld.long 0x0 6. "NMIMAP1CLR,NVM1 MAP Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
bitfld.long 0x0 5. "NMIMAP0CLR,NVM0 MAP Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "NMINVM1CLR,NVM1 Double Bit ECC Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
bitfld.long 0x0 3. "NMINVM0CLR,NVM 0 Double Bit ECC Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "NMICDCLR,Cache Data RAM Double Bit ECC Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
bitfld.long 0x0 1. "NMIPSCLR,PSRAM Double Bit ECC Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIDSCLR,DSRAM Double Bit ECC Error NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
line.long 0x4 "NMISRS,NMI Status Set Register"
|
|
bitfld.long 0x4 8. "NMISTOFSET,Stack Overflow NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
bitfld.long 0x4 7. "NMIWDTSET,Watchdog Timer NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
newline
|
|
bitfld.long 0x4 6. "NMIMAP1SET,NVM1 MAP Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
bitfld.long 0x4 5. "NMIMAP0SET,NVM0 MAP Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
newline
|
|
bitfld.long 0x4 4. "NMINVM1SET,NVM1 Double Bit ECC Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
bitfld.long 0x4 3. "NMINVM0SET,NVM 0 Double Bit ECC Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
newline
|
|
bitfld.long 0x4 2. "NMICDSET,Cache Data RAM Double Bit ECC Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
bitfld.long 0x4 1. "NMIPSSET,PSRAM Double Bit ECC Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
newline
|
|
bitfld.long 0x4 0. "NMIDSSET,DSRAM Double Bit ECC Error NMI Status Set" "0: NMI not Set,1: NMI Set"
|
|
group.long 0xA0++0x3
|
|
line.long 0x0 "NVM_OP_RESULT,NVM operation result"
|
|
hexmask.long 0x0 0.--31. 1. "OP_RESULT,NVM operation result in case of a write/erase operation in the background"
|
|
group.long 0x9C++0x3
|
|
line.long 0x0 "NVM_OP_STS,NVM Operation Status"
|
|
hexmask.long 0x0 0.--31. 1. "OP_STS,Operation Status"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "SBFA,System Bus Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 1. "SBFA,System Bus Fault Address"
|
|
group.long 0xAC++0x3
|
|
line.long 0x0 "STACK_OVF_ADDR,Stack Overflow Address Register"
|
|
hexmask.long.word 0x0 18.--30. 1. "STOF_ADDR_OFF_H,Higher DSRAM address offset boundary for stack overflow protection"
|
|
hexmask.long.word 0x0 2.--14. 1. "STOF_ADDR_OFF_L,Lower DSRAM address offset boundary for stack overflow protection"
|
|
group.long 0xA8++0x3
|
|
line.long 0x0 "STACK_OVF_CTRL,Stack Overflow Control Register"
|
|
bitfld.long 0x0 0. "STOF_EN,Stack Overflow Enable" "0: stack overflow disabled,1: stack overflow enabled"
|
|
group.long 0xB4++0x3
|
|
line.long 0x0 "STCALIB,System Tick Calibration Register"
|
|
hexmask.long 0x0 0.--25. 1. "STCALIB,System Tick Calibration"
|
|
rgroup.long 0xC0++0x3
|
|
line.long 0x0 "SYSWDT,System Watchdog Timer Value"
|
|
hexmask.long.word 0x0 0.--15. 1. "WDT,Watchdog Timer Current Value"
|
|
group.long 0xB8++0x7
|
|
line.long 0x0 "SYSWDTCON,System Watchdog Timer Control Register"
|
|
bitfld.long 0x0 5. "WDTBEN,Watchdog Window-Boundary Enable" "0: Watchdog Window-Boundary feature is disabled.,1: Watchdog Window-Boundary feature is enabled."
|
|
rbitfld.long 0x0 4. "WDTPR,Watchdog Prewarning Mode Flag" "0: Normal Mode (default after reset),1: A watchdog error is detected. The watchdog timer.."
|
|
newline
|
|
bitfld.long 0x0 2. "WDTEN,WDT Enable" "0: WDT is disabled,1: WDT is enabled"
|
|
bitfld.long 0x0 1. "WDTRS,WDT Refresh Start" "0,1"
|
|
newline
|
|
bitfld.long 0x0 0. "WDTIN,Watchdog Timer Input Frequency Selection" "0: Input Frequency is fcpu_clk/2,1: Input Frequency is fcpu_clk/128"
|
|
line.long 0x4 "SYSWDTREL,System Watchdog Timer Reload Register"
|
|
hexmask.long.byte 0x4 0.--7. 1. "WDTREL,Watchdog Timer Reload Value - Upper Watchdog Timer Byte"
|
|
group.long 0xC4++0x3
|
|
line.long 0x0 "SYSWDTWINB,System Watchdog Window-Boundary Count"
|
|
hexmask.long.byte 0x0 0.--7. 1. "WDTWINB,Watchdog Window-Boundary Count Value"
|
|
tree.end
|
|
tree "PLL (Phase Lock Loop)"
|
|
base ad:0x48008000
|
|
group.long 0x0++0xB
|
|
line.long 0x0 "CON0,PLL0 Control Register"
|
|
bitfld.long 0x0 31. "PLLEN,PLL Enable" "0: PLL disabled,1: PLL enabled"
|
|
bitfld.long 0x0 25. "RESLD,Lock Detection Reset" "0: No effect.,1: Reset lock flag and restart lock detection."
|
|
newline
|
|
bitfld.long 0x0 24. "FREERUN,Free-running Mode Select" "0: Reference Clock is connected to the PLL,1: Reference Clock is disconnected from PLL (Free.."
|
|
bitfld.long 0x0 20.--21. "INSEL,PLL Reference Clock Select" "0: HP_CLK selected synchronously as reference clock..,1: XTAL_CLK selected as reference clock,2: HP_CLK selected asynchronously as reference..,3: HP_CLK selected asynchronously as reference.."
|
|
newline
|
|
bitfld.long 0x0 16.--18. "K2DIV,K2-Divider Setting" "0: K2 = 2 (default) (decoded value 0x01),1: K2 = 3 (decoded value 0x02),2: Divider Setting,3: K2 = 5 (decoded value 0x04),4: K2 = 6 (decoded value 0x05),5: K2 = 7 (decoded value 0x06),6: K2 = 8 (decoded value 0x07),7: K2 = 9 (decoded value 0x08)"
|
|
hexmask.long.byte 0x0 8.--13. 1. "PDIV,P-Divider Setting"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--7. 1. "NDIV,N-Divider Setting"
|
|
line.long 0x4 "CON1,PLL1 Control Register"
|
|
bitfld.long 0x4 31. "PLLEN,PLL Enable" "0: PLL disabled,1: PLL enabled"
|
|
bitfld.long 0x4 25. "RESLD,Lock Detection Reset" "0: No effect.,1: Reset lock flag and restart lock detection."
|
|
newline
|
|
bitfld.long 0x4 24. "FREERUN,Freerunning Mode Select" "0: Reference Clock is connected to the PLL,1: Reference Clock is disconnected from PLL (Free.."
|
|
bitfld.long 0x4 20.--21. "INSEL,PLL Reference Clock Select" "0: HP_CLK selected synchronously as reference clock..,1: XTAL_CLK selected as reference clock,2: HP_CLK selected asynchronously as reference..,3: HP_CLK selected asynchronously as reference.."
|
|
newline
|
|
bitfld.long 0x4 16.--18. "K2DIV,K2-Divider Setting" "0: K2 = 2 (default) (decoded value 0x01),1: K2 = 3 (decoded value 0x02),2: Divider Setting,3: K2 = 5 (decoded value 0x04),4: K2 = 6 (decoded value 0x05),5: K2 = 7 (decoded value 0x06),6: K2 = 8 (decoded value 0x07),7: K2 = 9 (decoded value 0x08)"
|
|
hexmask.long.byte 0x4 8.--13. 1. "PDIV,P-Divider Setting"
|
|
newline
|
|
hexmask.long.byte 0x4 0.--7. 1. "NDIV,N-Divider Setting"
|
|
line.long 0x8 "SPCTR,PLL NDIV Spread Control Register"
|
|
hexmask.long.word 0x8 22.--31. 1. "SPUPVAL1,PLL1 NDIV Spread Update Interval"
|
|
bitfld.long 0x8 20.--21. "SPRANGE1,PLL1 NDIV Spread Range Value" "0: NDIV Spread in Range of +/- 1 Values,1: NDIV Spread in Range of +/- 2 Values,2: NDIV Spread in Range of +/- 3 Values,3: NDIV Spread in Range of +/- 4 Values"
|
|
newline
|
|
bitfld.long 0x8 16. "SPEN1,NDIV PLL1 Spread Enable" "0: NDIV spread feature disabled,1: NDIV spread feature enabled"
|
|
hexmask.long.word 0x8 6.--15. 1. "SPUPVAL0,PLL0 NDIV Spread Update Interval"
|
|
newline
|
|
bitfld.long 0x8 4.--5. "SPRANGE0,PLL0 NDIV Spread Range Value" "0: NDIV Spread in Range of +/- 1 Values,1: NDIV Spread in Range of +/- 2 Values,2: NDIV Spread in Range of +/- 3 Values,3: NDIV Spread in Range of +/- 4 Values"
|
|
bitfld.long 0x8 0. "SPEN0,NDIV PLL0 Spread Enable" "0: NDIV spread feature disabled,1: NDIV spread feature enabled"
|
|
rgroup.long 0xC++0x3
|
|
line.long 0x0 "STAT,PLL Status Register"
|
|
bitfld.long 0x0 17. "OSCSEL_STAT1,Oscillator Select Status PLL1" "0: hp_clk selected as reference,1: xtal_clk selected as reference"
|
|
bitfld.long 0x0 16. "OSCSEL_STAT0,Oscillator Select Status PLL0" "0: hp_clk selected as reference,1: xtal_clk selected as reference"
|
|
newline
|
|
bitfld.long 0x0 5. "PLL1_LOL_STS,PLL1 Loss Of Lock Status" "0: no PLL Loss of Lock occurred,1: a PLL Loss of Lock has occurred"
|
|
bitfld.long 0x0 4. "PLL0_LOL_STS,PLL0 Loss Of Lock Status" "0: no PLL Loss of Lock occurred,1: a PLL Loss of Lock has occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "LCK1,Lock Status PLL1" "0: PLL1 is not locked,1: PLL1 is locked"
|
|
bitfld.long 0x0 0. "LCK0,Lock Status PLL 0" "0: PLL0 is not locked,1: PLL0 is locked"
|
|
wgroup.long 0x10++0x7
|
|
line.long 0x0 "STATC,PLL Status Clear Register"
|
|
bitfld.long 0x0 1. "PLL1_LOL_STSCLR,PLL1 Loss Of Lock Status Clear" "0: Status not cleared,1: Status cleared"
|
|
bitfld.long 0x0 0. "PLL0_LOL_STSCLR,PLL0 Loss Of Lock Status Clear" "0: Status not cleared,1: Status cleared"
|
|
line.long 0x4 "STATS,PLL Status Set Register"
|
|
bitfld.long 0x4 1. "PLL1_LOL_STSSET,PLL1 Loss Of Lock Status Set" "0: Status not SET,1: Status SET"
|
|
bitfld.long 0x4 0. "PLL0_LOL_STSSET,PLL0 Loss Of Lock Status Set" "0: Status not SET,1: Status SET"
|
|
tree.end
|
|
tree "PMU (Power Management Unit)"
|
|
base ad:0x48000000
|
|
group.long 0x724++0x3
|
|
line.long 0x0 "CSC_CTRL,Current sense comparator control register"
|
|
bitfld.long 0x0 0. "CSC_DIS,Current sense comparator disable" "0: CSC enabled,1: CSC disabled"
|
|
group.long 0x5C++0x3
|
|
line.long 0x0 "CYC_CTRL,Cyclic sense / Cyclic wake control register"
|
|
bitfld.long 0x0 28.--29. "CYC_WAKE_E01,Cyclic wake timer exponent" "0: Exponent value is 0,1: Exponent value is 1,2: Exponent value is 2,3: Exponent value is 3"
|
|
newline
|
|
hexmask.long.byte 0x0 24.--27. 1. "CYC_WAKE_M03,Cyclic wake timer mantissa"
|
|
newline
|
|
bitfld.long 0x0 20.--21. "CYC_SENSE_E01,Cyclic sense timer exponent" "0: Exponent value is 0,1: Exponent value is 1,2: Exponent value is 2,3: Exponent value is 3"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--19. 1. "CYC_SENSE_M03,Cyclic sense timer mantissa"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "CYC_ON_TIME,On time in cyclic sense mode" "0: 150 us,1: 250 us,2: 500 us,3: 1 ms,4: 2 ms,5: 5 ms,6: 10 ms,7: 20 ms"
|
|
newline
|
|
bitfld.long 0x0 0. "CYC_SENSE_EN,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
rgroup.long 0x718++0x3
|
|
line.long 0x0 "FS_SSD,Safe state status register"
|
|
bitfld.long 0x0 2.--3. "FO_STS,Fail output status (FO)" "0: Fail output is inactive,1: Fail output is active,2: Fail output is active,3: Fail output is active"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "SSD_STS,Safe shutdown status" "0: Safe shutdown is inactive,1: Safe shutdown is active,2: Safe shutdown is active,3: Safe shutdown is active"
|
|
wgroup.long 0x71C++0x7
|
|
line.long 0x0 "FS_SSD_CLR,Safe state status clear register"
|
|
bitfld.long 0x0 1. "FO_STS_CLR,Fail output status clear (FO)" "0: Fail output status not cleared,1: Fail output status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "SSD_STS_CLR,Safe shutdown status clear" "0: Safe shutdown status not cleared,1: Safe shutdown status cleared"
|
|
line.long 0x4 "FS_SSD_SET,Safe state status set register"
|
|
bitfld.long 0x4 1. "FO_STS_SET,Fail output status set (FO)" "0: Fail output status not set,1: Fail output status set"
|
|
newline
|
|
bitfld.long 0x4 0. "SSD_STS_SET,Safe shutdown status set" "0: Safe shutdown status not set,1: Safe shutdown status set"
|
|
rgroup.long 0x70C++0x3
|
|
line.long 0x0 "FS_STS,Functional safety status register"
|
|
bitfld.long 0x0 16. "FO_OC_STS,FO overcurrent status (FO)" "0: No FO overcurrent occurred,1: FO overcurrent occurred"
|
|
newline
|
|
bitfld.long 0x0 14. "PIN_MON_STS,Pin monitor fail status (FI)" "0: No pin monitor fail occurred,1: Pin monitor fail occurred"
|
|
newline
|
|
bitfld.long 0x0 13. "CSC_EN_FAIL_STS,Current sense comparator enabling fail status" "0: No current sense comparator enable fail occurred,1: Bridge driver is enabled without having CSC and.."
|
|
newline
|
|
bitfld.long 0x0 12. "CSC_BIST_FAIL_STS,Current sense comparator self-test fail status" "0: No current sense comparator self-test fail..,1: Current sense comparator self-test fail occurred"
|
|
newline
|
|
bitfld.long 0x0 11. "CSC_OC_STS,Current Sense comparator overcurrent status" "0: No overcurrent occurred,1: overcurrent occurred"
|
|
newline
|
|
bitfld.long 0x0 10. "VAREF_OV_STS,VAREF overvoltage status" "0: No overvoltage occurred,1: overrvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 9. "VDDP_OT_STS,VDDP overtemperature status" "0: No VDDP overtemperature occurred,1: VDDP overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 8. "VDDP_OV_STS,VDDP overvoltage status" "0: No overvoltage occurred,1: overrvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 7. "VDDP_UV_STS,VDDP undervoltage status" "0: No undervoltage occurred,1: undervoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 6. "VDDC_OV_STS,VDDC overvoltage status" "0: No overvoltage occurred,1: overrvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 5. "VDDC_UV_STS,VDDC undervoltage status" "0: No undervoltage occurred,1: undervoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 4. "WD_TEST_FAIL_STS,Watchdog self-test fail status" "0: No watchdog self-test fail occurred,1: watchdog self-test fail occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "WD_FAIL_STS,Watchdog Fail status" "0: No watchdog fail occurred,1: watchdog fail occurred"
|
|
newline
|
|
bitfld.long 0x0 2. "VMSUP_OV_STS,Master supply overvoltage status" "0: No overvoltage occurred,1: overvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "VMSUP_UV_STS,Master supply undervoltage status" "0: No undervoltage occurred,1: undervoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "MCLK_FAIL_STS,Master clock watchdog fail status" "0: No master clock watchdog fail occurred,1: Master clock watchdog fail occurred"
|
|
wgroup.long 0x710++0x7
|
|
line.long 0x0 "FS_STS_CLR,Functional safety status clear register"
|
|
bitfld.long 0x0 16. "FO_OC_STS_CLR,FO overcurrent status clear (FO)" "0: FO overcurrent status not cleared,1: FO overcurrent status cleared"
|
|
newline
|
|
bitfld.long 0x0 14. "PIN_MON_STS_CLR,Pin monitor fail status (FI)" "0: Pin monitoring status not cleared,1: Pin monitoring status cleared"
|
|
newline
|
|
bitfld.long 0x0 13. "CSC_EN_FAIL_STS_CLR,Current sense comparator enable fail status" "0: Current sense comparator enable fail status not..,1: Current sense comparator enable fail status.."
|
|
newline
|
|
bitfld.long 0x0 12. "CSC_BIST_FAIL_STS_CLR,Current sense comparator self-test fail status" "0: Current sense comparator self-test status not..,1: Current sense comparator self-test status cleared"
|
|
newline
|
|
bitfld.long 0x0 11. "CSC_OC_STS_CLR,Current sense comparator overcurrent status" "0: Current sense comparator overcurrent status not..,1: Current sense comparator overcurrent status.."
|
|
newline
|
|
bitfld.long 0x0 10. "VAREF_OV_STS_CLR,VAREF overvoltage status" "0: VAREF overvoltage status not cleared,1: VAREF overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 9. "VDDP_OT_STS_CLR,VDDP overtemperature status" "0: VDDP overtemperature status not cleared,1: VDDP overtemperature status cleared"
|
|
newline
|
|
bitfld.long 0x0 8. "VDDP_OV_STS_CLR,VDDP overvoltage status" "0: VDDP overvoltage status not cleared,1: VDDP overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 7. "VDDP_UV_STS_CLR,VDDP undervoltage status" "0: VDDP undervoltage status not cleared,1: VDDP undervoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 6. "VDDC_OV_STS_CLR,VDDC overvoltage status" "0: VDDC overvoltage status not cleared,1: VDDC overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "VDDC_UV_STS_CLR,VDDC undervoltage status" "0: VDDC undervoltage status not cleared,1: VDDC undervoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "WD_TEST_FAIL_STS_CLR,Watchdog self test fail status" "0: Watchdog self test fail status not cleared,1: Watchdog self test fail status cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "WD_FAIL_STS_CLR,Watchdog fail status" "0: Watchdog fail status not cleared,1: Watchdog fail status cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "VMSUP_OV_STS_CLR,Master supply overvoltage status" "0: Master supply overvoltage status not cleared,1: Master supply overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "VMSUP_UV_STS_CLR,Master supply undervoltage status" "0: Master supply undervoltage status not cleared,1: Master supply undervoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "MCLK_FAIL_STS_CLR,Master clock watchdog fail status" "0: Master clock fail status not cleared,1: Master clock fail status cleared"
|
|
line.long 0x4 "FS_STS_SET,Functional safety status set register"
|
|
bitfld.long 0x4 16. "FO_OC_STS_SET,FO overcurrent status set (FO)" "0: FO overcurrent status not set,1: FO overcurrent status set"
|
|
newline
|
|
bitfld.long 0x4 14. "PIN_MON_STS_SET,Pin monitor fail status (FI)" "0: Pin monitoring status not set,1: Pin monitoring status set"
|
|
newline
|
|
bitfld.long 0x4 13. "CSC_EN_FAIL_STS_SET,Current sense comparator enable fail status" "0: Current sense comparator enable fail status not..,1: Current sense comparator enable fail status set"
|
|
newline
|
|
bitfld.long 0x4 12. "CSC_BIST_FAIL_STS_SET,Current sense comparator self test fail status" "0: Current sense comparator self test status not set,1: Current sense comparator selftest status set"
|
|
newline
|
|
bitfld.long 0x4 11. "CSC_OC_STS_SET,Current sense comparator overcurrent status" "0: Current sense comparator overcurrent status not..,1: Current sense comparator overcurrent status set"
|
|
newline
|
|
bitfld.long 0x4 10. "VAREF_OV_STS_SET,VAREF overvoltage status" "0: VAREF overvoltage status not set,1: VAREF overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 9. "VDDP_OT_STS_SET,VDDP overtemperature status" "0: VDDP overtemperature status not set,1: VDDP overtemperature status set"
|
|
newline
|
|
bitfld.long 0x4 8. "VDDP_OV_STS_SET,VDDP overvoltage status" "0: VDDP Overvoltage status not set,1: VDDP Overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 7. "VDDP_UV_STS_SET,VDDP undervoltage status" "0: VDDP undervoltage status not set,1: VDDP undervoltage status set"
|
|
newline
|
|
bitfld.long 0x4 6. "VDDC_OV_STS_SET,VDDC overvoltage status" "0: VDDC overvoltage status not set,1: VDDC overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 5. "VDDC_UV_STS_SET,VDDC undervoltage status" "0: VDDC undervoltage status not set,1: VDDC undervoltage status set"
|
|
newline
|
|
bitfld.long 0x4 4. "WD_TEST_FAIL_STS_SET,Watchdog self test fail status" "0: Watchdog self test fail status not set,1: Watchdog self test fail status set"
|
|
newline
|
|
bitfld.long 0x4 3. "WD_FAIL_STS_SET,Watchdog fail status" "0: Watchdog fail status not set,1: Watchdog fail status set"
|
|
newline
|
|
bitfld.long 0x4 2. "VMSUP_OV_STS_SET,Master supply overvoltage status" "0: Master supply overvoltage status not set,1: Master supply overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 1. "VMSUP_UV_STS_SET,Master supply undervoltage status" "0: Master supply undervoltage status not set,1: Master supply undervoltage status set"
|
|
newline
|
|
bitfld.long 0x4 0. "MCLK_FAIL_STS_SET,Master clock watchdog fail status" "0: Master clock fail status not set,1: Master clock fail status set"
|
|
group.long 0x98++0xB
|
|
line.long 0x0 "GPUDATA0,General purpose user data register"
|
|
hexmask.long 0x0 0.--31. 1. "DATA,Data storage"
|
|
line.long 0x4 "GPUDATA1,General purpose user data register"
|
|
hexmask.long 0x4 0.--31. 1. "DATA,Data storage"
|
|
line.long 0x8 "GPUDATA2,General purpose user data register"
|
|
hexmask.long 0x8 0.--31. 1. "DATA,Data storage"
|
|
group.long 0xD8++0x3
|
|
line.long 0x0 "MISC_CTRL,Miscellaneous control register"
|
|
bitfld.long 0x0 16. "TRIG_RST,Trigger Pin Reset" "0: No Pin Reset trigger,1: Trigger Pin Reset"
|
|
newline
|
|
bitfld.long 0x0 0. "FI_PU_EN,Failure input pull up enable" "0: Failure input pull up disabled,1: Failure Input pull up enabled"
|
|
group.long 0x78++0xB
|
|
line.long 0x0 "MON_CTRL1,MON input control register"
|
|
bitfld.long 0x0 5. "PD,Input pull down current source enable" "0: Pull down current source disabled,1: Pull down current source enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "PU,Input pull up current Source enable" "0: Pull up current source disabled,1: Pull up current source enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "CYC_SENSE_EN,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "WAKE_FALL,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "WAKE_RISE,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "EN,MON input enable" "0: MON disabled,1: MON enabled"
|
|
line.long 0x4 "MON_CTRL2,MON input control register"
|
|
bitfld.long 0x4 5. "PD,Input pull down current source enable" "0: Pull down current source disabled,1: Pull down current source enabled"
|
|
newline
|
|
bitfld.long 0x4 4. "PU,Input pull up current Source enable" "0: Pull up current source disabled,1: Pull up current source enabled"
|
|
newline
|
|
bitfld.long 0x4 3. "CYC_SENSE_EN,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x4 2. "WAKE_FALL,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "WAKE_RISE,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "EN,MON input enable" "0: MON disabled,1: MON enabled"
|
|
line.long 0x8 "MON_CTRL3,MON input control register"
|
|
bitfld.long 0x8 5. "PD,Input pull down current source enable" "0: Pull down current source disabled,1: Pull down current source enabled"
|
|
newline
|
|
bitfld.long 0x8 4. "PU,Input pull up current Source enable" "0: Pull up current source disabled,1: Pull up current source enabled"
|
|
newline
|
|
bitfld.long 0x8 3. "CYC_SENSE_EN,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x8 2. "WAKE_FALL,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x8 1. "WAKE_RISE,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
newline
|
|
bitfld.long 0x8 0. "EN,MON input enable" "0: MON disabled,1: MON enabled"
|
|
rgroup.long 0x84++0x3
|
|
line.long 0x0 "MON_STS,MON input status register"
|
|
bitfld.long 0x0 2. "MON3_STS,MON3 input status" "0: MON input low,1: MON input high"
|
|
newline
|
|
bitfld.long 0x0 1. "MON2_STS,MON2 input status" "0: MON input low,1: MON input high"
|
|
newline
|
|
bitfld.long 0x0 0. "MON1_STS,MON1 input status" "0: MON input low,1: MON input high"
|
|
rgroup.long 0x4C++0x3
|
|
line.long 0x0 "RESET_STS,Reset status register"
|
|
bitfld.long 0x0 13. "TMS_RST,TMS reset status" "0: No TMS reset occurred,1: TMS reset occurred"
|
|
newline
|
|
bitfld.long 0x0 12. "SEC_STACK_RST,Secure stack overflow reset status" "0: No secure stack overflow occurred,1: Secure stack overflow occurred"
|
|
newline
|
|
bitfld.long 0x0 11. "VDDC_UV_RST,VDDC undervoltage reset status" "0: No undervoltage reset occurred,1: undervoltage reset occurred"
|
|
newline
|
|
bitfld.long 0x0 10. "VDDP_UV_RST,VDDP undervoltage reset status" "0: No undervoltage reset occurred,1: undervoltage reset occurred"
|
|
newline
|
|
bitfld.long 0x0 9. "LOCKUP_RST,ARM core lockup reset status" "0: No lockup reset occurred,1: Lockup reset occurred"
|
|
newline
|
|
bitfld.long 0x0 8. "SOFT_RST,Soft reset status" "0: No soft reset occurred,1: Soft reset occurred"
|
|
newline
|
|
bitfld.long 0x0 7. "WDT_MCU_RST,MCU watchdog timer reset status" "0: No watchdog timer reset occurred,1: Watchdog timer reset occurred"
|
|
newline
|
|
bitfld.long 0x0 6. "FSWD_RST,Fail safe watchdog reset status" "0: No watchdog reset occurred,1: Watchdog reset occurred"
|
|
newline
|
|
bitfld.long 0x0 5. "PIN_RST,Pin-Reset reset status" "0: No pin reset occurred,1: Pin reset occurred"
|
|
newline
|
|
bitfld.long 0x0 4. "STOPEX_RST,Stop mode exit reset status" "0: No stop exit reset occurred,1: Stop exit reset occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "SLEEPEX_RST,Sleep mode exit reset status" "0: No Sleep Exit reset occurred,1: Sleep exit reset occurred"
|
|
newline
|
|
bitfld.long 0x0 2. "FS_SLEEPEX_RST,Fail Sleep mode exit reset status" "0: No Fail Sleep exit reset occurred,1: Fail Sleep exit reset occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "MCLK_WD_RST,Master clock watchdog reset status" "0: No master clock watchdog reset occurred,1: Master clock watchdog reset occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "VMSUP_UV_RST,Master supply undervoltage reset status" "0: No undervoltage reset occurred,1: undervoltage reset occurred"
|
|
wgroup.long 0x50++0x7
|
|
line.long 0x0 "RESET_STS_CLR,Reset status clear register"
|
|
bitfld.long 0x0 13. "TMS_RST_CLR,TMS reset Status Clear" "0: TMS reset status not cleared,1: TMS reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 12. "SEC_STACK_RST_CLR,Secure stack overflow reset status clear" "0: Secure stack overflow reset status not cleared,1: Secure stack overflow reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 11. "VDDC_UV_RST_CLR,VDDC undervoltage reset status clear" "0: VDDC undervoltage reset status not cleared,1: VDDC undervoltage reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 10. "VDDP_UV_RST_CLR,VDDP undervoltage reset status clear" "0: VDDP undervoltage reset status not cleared,1: VDDP undervoltage reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 9. "LOCKUP_RST_CLR,ARM core lockup reset status" "0: Lockup reset status not cleared,1: Lockup reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 8. "SOFT_RST_CLR,Soft reset status clear" "0: Soft reset status not cleared,1: Soft reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 7. "WDT_MCU_RST_CLR,MCU watchdog timer reset status clear" "0: Watchdog timer reset status not cleared,1: Watchdog timer reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 6. "FSWD_RST_CLR,Fail safe watchdog reset status clear" "0: Watchdog fail reset status not cleared,1: Watchdog fail reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "PIN_RST_CLR,Pin reset Status Clear" "0: Pin reset status not cleared,1: Pin reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "STOPEX_RST_CLR,Stop mode exit reset status clear" "0: Stop exit reset status not cleared,1: Stop exit reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "SLEEPEX_RST_CLR,Sleep mode exit reset status clear" "0: Sleep exit reset status not cleared,1: Sleep exit reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "FS_SLEEPEX_RST_CLR,Fail Sleep mode exit reset status clear" "0: Fail Sleep exit reset status not cleared,1: Fail Sleep exit reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "MCLK_WD_RST_CLR,Master clock watchdog reset status clear" "0: Master clock watchdog reset status not cleared,1: Master clock watchdog reset status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "VMSUP_UV_RST_CLR,Master supply undervoltage reset status clear" "0: Master supply undervoltage reset status not..,1: Master supply undervoltage reset status cleared"
|
|
line.long 0x4 "RESET_STS_SET,Reset status set register"
|
|
bitfld.long 0x4 13. "TMS_RST_SET,TNS reset status set" "0: TMS reset status not set,1: TMS reset status set"
|
|
newline
|
|
bitfld.long 0x4 12. "SEC_STACK_RST_SET,Secure stack overflow reset status set" "0: Secure stack overflow status not set,1: Secure stack overflow reset status set"
|
|
newline
|
|
bitfld.long 0x4 11. "VDDC_UV_RST_SET,VDDC undervoltage reset status set" "0: VDDC undervoltage reset status not set,1: VDDC undervoltage reset status set"
|
|
newline
|
|
bitfld.long 0x4 10. "VDDP_UV_RST_SET,VDDP undervoltage reset status set" "0: VDDP undervoltage reset status not set,1: VDDP undervoltage reset status set"
|
|
newline
|
|
bitfld.long 0x4 9. "LOCKUP_RST_SET,ARM core lockup reset status set" "0: Lockup reset status not set,1: Lockup reset status set"
|
|
newline
|
|
bitfld.long 0x4 8. "SOFT_RST_SET,Soft reset status set" "0: Soft reset status not set,1: Soft reset status set"
|
|
newline
|
|
bitfld.long 0x4 7. "WDT_MCU_RST_SET,MCU watchdog timer reset status set" "0: Watchdog timer reset status not set,1: Watchdog timer reset status set"
|
|
newline
|
|
bitfld.long 0x4 6. "FSWD_RST_SET,Fail safe watchdog reset status set" "0: Watchdog fail reset status not set,1: Watchdog fail reset status set"
|
|
newline
|
|
bitfld.long 0x4 5. "PIN_RST_SET,Pin reset status set" "0: Pin reset status not set,1: Pin reset status set"
|
|
newline
|
|
bitfld.long 0x4 4. "STOPEX_RST_SET,Stop mode exit reset status set" "0: Stop exit reset status not set,1: Stop exit reset status set"
|
|
newline
|
|
bitfld.long 0x4 3. "SLEEPEX_RST_SET,Sleep mode exit reset status set" "0: Sleep exit reset status not set,1: Sleep exit reset status set"
|
|
newline
|
|
bitfld.long 0x4 2. "FS_SLEEPEX_RST_SET,Fail Sleep mode exit reset status set" "0: Fail Sleep exit reset status not set,1: Fail Sleep exit reset status set"
|
|
newline
|
|
bitfld.long 0x4 1. "MCLK_WD_RST_SET,Master clock watchdog reset status set" "0: Master clock watchdog reset status not set,1: Master clock watchdog reset status set"
|
|
newline
|
|
bitfld.long 0x4 0. "VMSUP_UV_RST_SET,Master supply undervoltage reset status set" "0: Master supply undervoltage status not set,1: Master supply undervoltage status set"
|
|
group.long 0x48++0x3
|
|
line.long 0x0 "RST_CTRL,RESET pin control register"
|
|
bitfld.long 0x0 0.--2. "TFB,Reset blind time selection" "0: 8 us,1: 16 us,2: 31 us,3: 63 us,4: 127 us,5: 255 us,6: 511 us,7: 1023 us"
|
|
group.long 0xE4++0x3
|
|
line.long 0x0 "START_CONFIG,Start configuration control register"
|
|
bitfld.long 0x0 1. "RST_PIN_EN,Reset PIN enable" "0: Pin P0.10 used as GPIO,1: Pin P0.10 used as RESET pin"
|
|
group.long 0x14++0x7
|
|
line.long 0x0 "VDDC_CTRL,VDDC voltage regulator control register"
|
|
bitfld.long 0x0 0.--1. "MCNFSTOP,Stop mode configuration of VDDC regulator" "0: Regulator is configured to adaptive mode in Stop..,1: Regulator is configured to low current mode in..,2: Regulator is configured to low current mode in..,3: Regulator is configured to high current mode in.."
|
|
line.long 0x4 "VDDC_IRQEN,VDDC interrupt enable register"
|
|
bitfld.long 0x4 1. "OV_IEN,VDDC overvoltage interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "UVWARN_IEN,VDDC undervoltage warning interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x1C++0x3
|
|
line.long 0x0 "VDDC_STS,VDDC regulator status register"
|
|
bitfld.long 0x0 21. "HCM_STS,VDDC high current mode status" "0: No high current mode occurred,1: High current mode occurred"
|
|
newline
|
|
bitfld.long 0x0 16. "UVWARN_STS,VDDC undervoltage warning status" "0: No undervoltage warning occurred,1: Undervoltage warning occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "OV_IS,VDDC overvoltage interrupt status" "0: No overvoltage occurred,1: Overvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "UVWARN_IS,VDDC undervoltage warning interrupt status" "0: No undervoltage warning occurred,1: Undervoltage warning occurred"
|
|
wgroup.long 0x20++0x7
|
|
line.long 0x0 "VDDC_STS_CLR,VDDC regulator status clear register"
|
|
bitfld.long 0x0 21. "HCM_STS_CLR,VDDC high current mode status clear" "0: High current mode status not cleared,1: High current mode status cleared"
|
|
newline
|
|
bitfld.long 0x0 16. "UVWARN_STS_CLR,VDDC undervoltage warning status clear" "0: Undervoltage warning status not cleared,1: Undervoltage warning status cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "OV_IS_CLR,Overvoltage interrupt status clear" "0: Overvoltage status not cleared,1: Overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "UVWARN_IS_CLR,VDDC undervoltage warning interrupt status clear" "0: Undervoltage warning status not cleared,1: Undervoltage warning status cleared"
|
|
line.long 0x4 "VDDC_STS_SET,VDDC regulator status set register"
|
|
bitfld.long 0x4 21. "HCM_STS_SET,VDDC high current mode status set" "0: High current mode status not set,1: High current mode status set"
|
|
newline
|
|
bitfld.long 0x4 16. "UVWARN_STS_SET,VDDC undervoltage warning status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
newline
|
|
bitfld.long 0x4 1. "OV_IS_SET,VDDC overvoltage interrupt status set" "0: Overvoltage status not set,1: Overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 0. "UVWARN_IS_SET,VDDC undervoltage warning interrupt status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
group.long 0x28++0x7
|
|
line.long 0x0 "VDDEXT_CTRL,VDDEXT voltage regulator control register"
|
|
bitfld.long 0x0 1. "CYC_EN,VDDEXT cyclic sense enable" "0: VDDEXT regulator with cyclic sense disabled,1: VDDEXT regulator with cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "EN,VDDEXT enable" "0: VDDEXT regulator disabled,1: VDDEXT regulator enabled"
|
|
line.long 0x4 "VDDEXT_IRQEN,VDDEXT interrupt enable register"
|
|
bitfld.long 0x4 1. "OT_IEN,VDDEXT overtemperature interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "UV_IEN,VDDEXT undervoltage interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x30++0x3
|
|
line.long 0x0 "VDDEXT_STS,VDDEXT regulator status register"
|
|
bitfld.long 0x0 17. "OT_STS,VDDEXT overtemperature status" "0: No overtemperature occurred,1: Overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 16. "UV_STS,VDDEXT undervoltage status" "0: No undervoltage occurred,1: Undervoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "OT_IS,VDDEXT overtemperature interrupt status" "0: No overtemperature occurred,1: Overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "UV_IS,VDDEXT undervoltage interrupt status" "0: No undervoltage occurred,1: Undervoltage occurred"
|
|
wgroup.long 0x34++0x7
|
|
line.long 0x0 "VDDEXT_STS_CLR,VDDEXT regulator status register clear"
|
|
bitfld.long 0x0 17. "OT_STS_CLR,VDDEXT overtemperature status clear" "0: Overtemperature status not cleared,1: Overtemperature status cleared"
|
|
newline
|
|
bitfld.long 0x0 16. "UV_STS_CLR,VDDEXT undervoltage status clear" "0: Undervoltage warning status not cleared,1: Undervoltage warning status cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "OT_IS_CLR,VDDEXT overtemperature interrupt status clear" "0: Overtemperature status not cleared,1: Overtemperature status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "UV_IS_CLR,VDDEXT undervoltage interrupt status clear" "0: Undervoltage warning status not cleared,1: Undervoltage warning status cleared"
|
|
line.long 0x4 "VDDEXT_STS_SET,VDDEXT regulator status register set"
|
|
bitfld.long 0x4 17. "OT_STS_SET,VDDEXT overtemperature status set" "0: Overtemperature status not set,1: Overtemperature status set"
|
|
newline
|
|
bitfld.long 0x4 16. "UV_STS_SET,VDDEXT undervoltage status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
newline
|
|
bitfld.long 0x4 1. "OT_IS_SET,VDDEXT overtemperature interrupt status set" "0: Overtemperature status not set,1: Overtemperature status set"
|
|
newline
|
|
bitfld.long 0x4 0. "UV_IS_SET,VDDEXT undervoltage interrupt status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
group.long 0x0++0x7
|
|
line.long 0x0 "VDDP_CTRL,VDDP voltage regulator control register"
|
|
bitfld.long 0x0 2. "ITH_SEL,Select current threshold for LCM/HCM mode" "0: low threshold,1: high threshold"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "MCNFSTOP,Stop mode configuration of VDDP regulator" "0: Regulator is configured to adaptive mode in Stop..,1: Regulator is configured to low current mode in..,2: Regulator is configured to low current mode in..,3: Regulator is configured to high current mode in.."
|
|
line.long 0x4 "VDDP_IRQEN,VDDP interrupt enable register"
|
|
bitfld.long 0x4 1. "OV_IEN,VDDP overvoltage interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "UVWARN_IEN,VDDP undervoltage warning interrupt enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x8++0x3
|
|
line.long 0x0 "VDDP_STS,VDDP regulator status register"
|
|
bitfld.long 0x0 21. "HCM_STS,VDDP high current mode status" "0: No high current mode occurred,1: High current mode occurred"
|
|
newline
|
|
bitfld.long 0x0 20. "ILIM_STS,VDDP current limitation status" "0: No current limitation occurred,1: Current limitation occurred"
|
|
newline
|
|
bitfld.long 0x0 16. "UVWARN_STS,VDDP undervoltage warning status" "0: No undervoltage warning occurred,1: Undervoltage warning occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "OV_IS,VDDP overvoltage interrupt status" "0: No overvoltage occurred,1: Overvoltage occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "UVWARN_IS,VDDP undervoltage warning interrupt status" "0: No undervoltage warning occurred,1: Undervoltage warning occurred"
|
|
wgroup.long 0xC++0x7
|
|
line.long 0x0 "VDDP_STS_CLR,VDDP regulator status clear register"
|
|
bitfld.long 0x0 21. "HCM_STS_CLR,VDDP high current mode status clear" "0: High current mode status not cleared,1: High current mode status cleared"
|
|
newline
|
|
bitfld.long 0x0 20. "ILIM_STS_CLR,VDDP current limitation status clear" "0: Current limitation status not cleared,1: Current limitation status cleared"
|
|
newline
|
|
bitfld.long 0x0 16. "UVWARN_STS_CLR,VDDP undervoltage warning status clear" "0: Undervoltage status warning not cleared,1: Undervoltage status warning cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "OV_IS_CLR,VDDP overvoltage interrupt status clear" "0: Overvoltage status not cleared,1: Overvoltage status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "UVWARN_IS_CLR,VDDP undervoltage warning interrupt status clear" "0: Undervoltage warning status not cleared,1: Undervoltage warning status cleared"
|
|
line.long 0x4 "VDDP_STS_SET,VDDP regulator status set register"
|
|
bitfld.long 0x4 21. "HCM_STS_SET,VDDP high current mode status set" "0: High current mode status not set,1: High current mode status set"
|
|
newline
|
|
bitfld.long 0x4 20. "ILIM_STS_SET,VDDP Ilimit status set" "0: Ilimit status not set,1: Ilimit status set"
|
|
newline
|
|
bitfld.long 0x4 16. "UVWARN_STS_SET,VDDP undervoltage warning status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
newline
|
|
bitfld.long 0x4 1. "OV_IS_SET,VDDP overvoltage interrupt status set" "0: Overvoltage status not set,1: Overvoltage status set"
|
|
newline
|
|
bitfld.long 0x4 0. "UVWARN_IS_SET,VDDP undervoltage warning interrupt status set" "0: Undervoltage warning status not set,1: Undervoltage warning status set"
|
|
group.long 0x88++0x3
|
|
line.long 0x0 "WAKE_CTRL,Wake control register"
|
|
bitfld.long 0x0 29. "VDDC_RED_EN,Stop mode - VDDC output voltage reduction enable" "0: VDDC is not reduced in Stop mode,1: VDDC is reduced in Stop mode"
|
|
newline
|
|
bitfld.long 0x0 24. "VSDOV_WAKE_EN,VSD overvoltage wake enable" "0: VSD overvoltage wake disabled,1: VSD overvoltage wake enabled"
|
|
newline
|
|
bitfld.long 0x0 23. "VDDEXT_UV_WAKE_EN,Stop mode VDDEXT undervoltage wake enable" "0: VDDEXT undervoltage wake disabled,1: VDDEXT undervoltage wake enabled"
|
|
newline
|
|
bitfld.long 0x0 22. "VDDEXT_OT_WAKE_EN,Stop mode VDDEXT overtemperature wake enable" "0: VDDEXT overtemperature wake disabled,1: VDDEXT overtemperature wake enabled"
|
|
newline
|
|
bitfld.long 0x0 21. "VDDC_HCM_WAKE_EN,Stop mode VDDC high current mode wake enable" "0: VDDC high current mode wake disabled,1: VDDC high current mode wake enabled"
|
|
newline
|
|
bitfld.long 0x0 20. "VDDC_OV_WAKE_EN,Stop mode VDDC overvoltage wake enable" "0: VDDC overvoltage wake disabled,1: VDDC overvoltage wake enabled"
|
|
newline
|
|
bitfld.long 0x0 19. "VDDC_UVWARN_WAKE_EN,Stop mode VDDC undervoltage warning wake enable" "0: VDDC undervoltage warning wake disabled,1: VDDC undervoltage warning wake enabled"
|
|
newline
|
|
bitfld.long 0x0 18. "VDDP_HCM_WAKE_EN,Stop mode VDDP high current mode wake enable" "0: VDDP high current mode wake disabled,1: VDDP high current mode wake enabled"
|
|
newline
|
|
bitfld.long 0x0 17. "VDDP_OV_WAKE_EN,Stop mode VDDP overvoltage wake enable" "0: VDDP overvoltage wake disabled,1: VDDP overvoltage wake enabled"
|
|
newline
|
|
bitfld.long 0x0 16. "VDDP_UVWARN_WAKE_EN,Stop mode VDDP undervoltage warning wake enable" "0: VDDP undervoltage warning wake disabled,1: VDDP undervoltage warning wake enabled"
|
|
newline
|
|
bitfld.long 0x0 14. "MON3_WAKE_EN,MON3 wake enable" "0: MON wake disabled,1: MON wake enabled"
|
|
newline
|
|
bitfld.long 0x0 13. "MON2_WAKE_EN,MON2 wake enable" "0: MON wake disabled,1: MON wake enabled"
|
|
newline
|
|
bitfld.long 0x0 12. "MON1_WAKE_EN,MON1 wake enable" "0: MON wake disabled,1: MON wake enabled"
|
|
newline
|
|
bitfld.long 0x0 9. "GPIO5_WAKE_EN,GPIO5 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 8. "GPIO4_WAKE_EN,GPIO4 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 7. "GPIO3_WAKE_EN,GPIO3 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 6. "GPIO2_WAKE_EN,GPIO2 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 5. "GPIO1_WAKE_EN,GPIO1 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "GPIO0_WAKE_EN,GPIO0 wake enable" "0: GPIO wake disabled,1: GPIO wake enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "CYC_WAKE_EN,Cyclic wake enable" "0: Cyclic wake disabled,1: Cyclic wake enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "CAN_WAKE_EN,CAN wake enable" "0: CAN wake disabled,1: CAN wake enabled"
|
|
wgroup.long 0x40++0x7
|
|
line.long 0x0 "WAKE_FAIL_CLR,Wake fail status clear register"
|
|
bitfld.long 0x0 6. "VDDC_OC_CLR,VDDC overcurrent status clear" "0: Overcurrent status not cleared,1: Overcurrent status cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "VDDP_OT_CLR,VDDP regulator overtemperature status clear" "0: VDDP overtemperature status not cleared,1: VDDP overtemperature status cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "FSWD_SEQ_FAIL_CLR,Fail safe watchdog sequential fail status clear" "0: Watchdog sequential fail status not cleared,1: Watchdog sequential fail status cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "SYS_OT_CLR,System overtemperature status clear" "0: System overtemperature status not cleared,1: System overtemperature status cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "HPCLK_FAIL_CLR,HP clock fail status clear" "0: HPCLK status not cleared,1: HPCLK status cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "VDDC_TMOUT_CLR,VDDP regulator timeout status clear" "0: VDDC timeout status not cleared,1: VDDC timeout status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "VDDP_TMOUT_CLR,VDDP Regulator timeout Status Clear" "0: VDDP timeout status not cleared,1: VDDP timeout status cleared"
|
|
line.long 0x4 "WAKE_FAIL_SET,Wake fail status set register"
|
|
bitfld.long 0x4 6. "VDDC_OC_SET,VDDC overcurrent status set" "0: Overcurrent status not set,1: Overcurrent status set"
|
|
newline
|
|
bitfld.long 0x4 5. "VDDP_OT_SET,VDDP regulator overtemperature status set" "0: VDDP overtemperature status not set,1: VDDP overtemperature status set"
|
|
newline
|
|
bitfld.long 0x4 4. "FSWD_SEQ_FAIL_SET,Fails safe watchdog sequential fail status set" "0: Watchdog sequential fail status not set,1: Watchdog sequential fail status set"
|
|
newline
|
|
bitfld.long 0x4 3. "SYS_OT_SET,System overtemperature status set" "0: System overtemperature status not set,1: System overtemperature status set"
|
|
newline
|
|
bitfld.long 0x4 2. "HPCLK_FAIL_SET,HP clock fail status set" "0: HPCLK fail status not set,1: HPCLK fail status set"
|
|
newline
|
|
bitfld.long 0x4 1. "VDDC_TMOUT_SET,VDDP regulator timeout status set" "0: VDDC timeout status not set,1: VDDC timeout status set"
|
|
newline
|
|
bitfld.long 0x4 0. "VDDP_TMOUT_SET,VDDP regulator timeout status set" "0: VDDP timeout status not set,1: VDDP timeout status set"
|
|
rgroup.long 0x3C++0x3
|
|
line.long 0x0 "WAKE_FAIL_STS,Wake fail status register"
|
|
bitfld.long 0x0 6. "VDDC_OC,VDDC overcurrent Status" "0: No overcurrent occurred,1: Overcurrent occurred"
|
|
newline
|
|
bitfld.long 0x0 5. "VDDP_OT,VDDP regulator overtemperature status" "0: No VDDP overtemperature occurred,1: VDDP overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 4. "FSWD_SEQ_FAIL,Fail safe watchdog sequential fail status" "0: No sequential watchdog fail occurred,1: Sequential watchdog fail occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "SYS_OT,System overtemperature status" "0: No system overtemperature occurred,1: System overtemperature occurred"
|
|
newline
|
|
bitfld.long 0x0 2. "HPCLK_FAIL,HP clock fail status" "0: No HPCLK fail occurred,1: HPCLK fail occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "VDDC_TMOUT,VDDP regulator timeout" "0: No timeout occurred,1: Timeout occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "VDDP_TMOUT,VDDP regulator timeout" "0: No timeout occurred,1: Timeout occurred"
|
|
group.long 0x58++0x3
|
|
line.long 0x0 "WAKE_FILT_CTRL,Wake up filter control register"
|
|
bitfld.long 0x0 2.--3. "GPIO_FT,GPIO wake up filter time selection" "0: 4 us,1: 8us,2: 16 us,3: 32 us"
|
|
newline
|
|
bitfld.long 0x0 1. "MON_FT,MON wake up filter time selection" "0: 16 us,1: 32 us"
|
|
group.long 0x60++0x17
|
|
line.long 0x0 "WAKE_GPIO_CTRL0,GPIO wake control register"
|
|
hexmask.long.byte 0x0 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0x0 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
line.long 0x4 "WAKE_GPIO_CTRL1,GPIO wake control register"
|
|
hexmask.long.byte 0x4 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0x4 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x4 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
line.long 0x8 "WAKE_GPIO_CTRL2,GPIO wake control register"
|
|
hexmask.long.byte 0x8 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0x8 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x8 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x8 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
line.long 0xC "WAKE_GPIO_CTRL3,GPIO wake control register"
|
|
hexmask.long.byte 0xC 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0xC 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0xC 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0xC 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
line.long 0x10 "WAKE_GPIO_CTRL4,GPIO wake control register"
|
|
hexmask.long.byte 0x10 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0x10 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x10 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x10 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
line.long 0x14 "WAKE_GPIO_CTRL5,GPIO wake control register"
|
|
hexmask.long.byte 0x14 8.--12. 1. "INP,GPIO input pointer"
|
|
newline
|
|
bitfld.long 0x14 2. "CYC,Cyclic sense enable" "0: Cyclic sense disabled,1: Cyclic sense enabled"
|
|
newline
|
|
bitfld.long 0x14 1. "FA,Falling edge wake enable" "0: Falling edge wake disabled,1: Falling edge wake enabled"
|
|
newline
|
|
bitfld.long 0x14 0. "RI,Rising edge wake enable" "0: Rising edge wake disabled,1: Rising edge wake enabled"
|
|
group.long 0x8C++0x3
|
|
line.long 0x0 "WAKE_STS,Wake status register"
|
|
bitfld.long 0x0 24. "VSD_OV,VSD overvoltage wake status" "0: No VSD overvoltage wake occurred,1: VSD overvoltage wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 23. "VDDEXT_UV,VDDEXT undervoltage wake status" "0: No VDDEXT undervoltage wake occurred,1: VDDEXT undervoltage wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 22. "VDDEXT_OT,VDDEXT overtemperature wake status" "0: No VDDEXT overtemperature wake occurred,1: VDDEXT overtemperature wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 21. "VDDC_HCM,VDDC high current mode wake status" "0: No VDDC high current mode wake occurred,1: VDDC high current mode wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 20. "VDDC_OV,VDDC overvoltage wake status" "0: No VDDC overvoltage wake occurred,1: VDDC overvoltage wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 19. "VDDC_UVWARN,VDDC undervoltage warning wake status" "0: No VDDC undervoltage warning wake occurred,1: VDDC undervoltage warning wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 18. "VDDP_HCM,VDDP high current mode wake Status" "0: No VDDP high current mode wake occurred,1: VDDP high current mode wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 17. "VDDP_OV,VDDP overvoltage wake status" "0: No VDDP overvoltage wake occurred,1: VDDP overvoltage wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 16. "VDDP_UVWARN,VDDP undervoltage warning wake status" "0: No VDDP undervoltage warning wake occurred,1: VDDP undervoltage warning wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 14. "MON3,MON3 wake status" "0: no MON wake occurred,1: MON wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 13. "MON2,MON2 wake status" "0: no MON wake occurred,1: MON wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 12. "MON1,MON1 wake status" "0: no MON wake occurred,1: MON wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 9. "GPIO5,GPIO5 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 8. "GPIO4,GPIO4 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 7. "GPIO3,GPIO3 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 6. "GPIO2,GPIO2 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 5. "GPIO1,GPIO1 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 4. "GPIO0,GPIO0 wake status" "0: no GPIO wake occurred,1: GPIO wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 2. "CYC_WAKE,Cyclic wake status" "0: No cyclic wake occurred,1: Cyclic wake occurred"
|
|
newline
|
|
rbitfld.long 0x0 0. "CAN,CAN wake status" "0: No CAN wake occurred,1: CAN wake occurred"
|
|
wgroup.long 0x90++0x7
|
|
line.long 0x0 "WAKE_STS_CLR,Wake status clear register"
|
|
bitfld.long 0x0 24. "VSD_OV_CLR,VSD undervoltage wake status clear" "0: VSD overvoltage wake status not cleared,1: VSD overvoltage wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 23. "VDDEXT_UV_CLR,VDDEXT undervoltage wake status clear" "0: VDDEXT undervoltage wake status not cleared,1: VDDEXT undervoltage wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 22. "VDDEXT_OT_CLR,VDDEXT overtemperature wake status clear" "0: VDDEXT overtemperature wake status not cleared,1: VDDEXT overtemperature wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 21. "VDDC_HCM_CLR,VDDC high current mode wake status clear" "0: VDDC high current mode wake status not cleared,1: VDDP high current mode wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 20. "VDDC_OV_CLR,VDDC overvoltage wake status clear" "0: VDDC overvoltage wake status not cleared,1: VDDC overvoltage wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 19. "VDDC_UVWARN_CLR,VDDC undervoltage warning wake status clear" "0: VDDC undervoltage warning wake status not cleared,1: VDDC undervoltage warning wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 18. "VDDP_HCM_CLR,VDDP high current mode wake status clear" "0: VDDP high current mode wake status not cleared,1: VDDP high current mode wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 17. "VDDP_OV_CLR,VDDP overvoltage wake status clear" "0: VDDP overvoltage wake status not cleared,1: VDDP overvoltage wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 16. "VDDP_UVWARN_CLR,VDDP undervoltage warning wake status clear" "0: VDDP undervoltage warning wake status not cleared,1: VDDP undervoltage warning wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 14. "MON3_CLR,MON3 wake status clear" "0: MON wake status not cleared,1: MON wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 13. "MON2_CLR,MON2 wake status clear" "0: MON wake status not cleared,1: MON wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 12. "MON1_CLR,MON1 wake status clear" "0: MON wake status not cleared,1: MON wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 9. "GPIO5_CLR,GPIO5 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 8. "GPIO4_CLR,GPIO4 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 7. "GPIO3_CLR,GPIO3 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 6. "GPIO2_CLR,GPIO2 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "GPIO1_CLR,GPIO1 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "GPIO0_CLR,GPIO0 wake status clear" "0: GPIO wake status not cleared,1: GPIO wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "CYC_WAKE_CLR,Cyclic wake status" "0: Cyclic wake status not cleared,1: Cyclic wake status cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "CAN_CLR,CAN wake status clear" "0: CAN wake status not cleared,1: CAN wake status cleared"
|
|
line.long 0x4 "WAKE_STS_SET,Wake status set register"
|
|
bitfld.long 0x4 24. "VSD_OV_SET,VSD overvoltage wake status set" "0: VSD overvoltage wake status not set,1: VSD overvoltage wake status set"
|
|
newline
|
|
bitfld.long 0x4 23. "VDDEXT_UV_SET,VDDEXT undervoltage wake status set" "0: VDDEXT undervoltage wake status not set,1: VDDEXT undervoltage wake status set"
|
|
newline
|
|
bitfld.long 0x4 22. "VDDEXT_OT_SET,VDDEXT overtemperature wake status set" "0: VDDEXT overtemperature wake status not set,1: VDDEXT overtemperature wake status set"
|
|
newline
|
|
bitfld.long 0x4 21. "VDDC_HCM_SET,VDDC high current mode wake status set" "0: VDDC high current mode wake status not set,1: VDDC high current mode wake status set"
|
|
newline
|
|
bitfld.long 0x4 20. "VDDC_OV_SET,VDDC overvoltage wake status set" "0: VDDC overvoltage wake status not set,1: VDDC overvoltage wake status set"
|
|
newline
|
|
bitfld.long 0x4 19. "VDDC_UVWARN_SET,VDDC undervoltage warning wake status set" "0: VDDC undervoltage warning wake status not set,1: VDDC undervoltage warning wake status set"
|
|
newline
|
|
bitfld.long 0x4 18. "VDDP_HCM_SET,VDDP high current mode wake status set" "0: VDDP high current mode wake status not set,1: VDDP high current mode wake status set"
|
|
newline
|
|
bitfld.long 0x4 17. "VDDP_OV_SET,VDDP overvoltage wake status set" "0: VDDP overvoltage wake status not set,1: VDDP overvoltage wake status set"
|
|
newline
|
|
bitfld.long 0x4 16. "VDDP_UVWARN_SET,VDDP undervoltage warning wake status set" "0: VDDP undervoltage warning wake status not set,1: VDDP undervoltage warning wake status set"
|
|
newline
|
|
bitfld.long 0x4 14. "MON3_SET,MON3 wake status set" "0: MON wake status not set,1: MON wake status set"
|
|
newline
|
|
bitfld.long 0x4 13. "MON2_SET,MON2 wake status set" "0: MON wake status not set,1: MON wake status set"
|
|
newline
|
|
bitfld.long 0x4 12. "MON1_SET,MON1 wake status set" "0: MON wake status not set,1: MON wake status set"
|
|
newline
|
|
bitfld.long 0x4 9. "GPIO5_SET,GPIO5 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 8. "GPIO4_SET,GPIO4 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 7. "GPIO3_SET,GPIO3 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 6. "GPIO2_SET,GPIO2 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 5. "GPIO1_SET,GPIO1 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 4. "GPIO0_SET,GPIO0 wake status set" "0: GPIO wake status not set,1: GPIO wake status set"
|
|
newline
|
|
bitfld.long 0x4 2. "CYC_WAKE_SET,Cyclic wake status set" "0: Cyclic wake status not set,1: Cyclic wake status set"
|
|
newline
|
|
bitfld.long 0x4 0. "CAN_SET,CAN wake status set" "0: CAN wake status not set,1: CAN wake status set"
|
|
group.long 0x700++0xB
|
|
line.long 0x0 "WD_CTRL,Watchdog control register"
|
|
bitfld.long 0x0 24.--25. "SOW,Short open window selection - Can only be configured in LOW" "0: Disabled,1: two successive short open window allowed,2: three successive short open windows allowed,3: four successive short open windows allowed"
|
|
newline
|
|
hexmask.long.byte 0x0 16.--21. 1. "WDP,Watchdog period selection"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "EN,Watchdog enable" "0: Watchdog disabled,1: Watchdog enabled (do not use),2: Watchdog enabled (do not use),3: Watchdog enabled"
|
|
line.long 0x4 "WD_TRIG,Watchdog trigger register"
|
|
bitfld.long 0x4 0. "TRIG,Trigger bit for long open- /window Mode" "0,1"
|
|
line.long 0x8 "WD_TRIG_SOW,Watchdog SOW trigger register"
|
|
bitfld.long 0x8 0. "TRIG,Trigger bit for short open window mode" "0,1"
|
|
tree.end
|
|
tree "SCU (System Control Unit)"
|
|
base ad:0x48004000
|
|
group.long 0x4++0x7
|
|
line.long 0x0 "CLKCON,Peripheral Clock Prescaler Register"
|
|
bitfld.long 0x0 27. "DIV2CLKOUT,CLKOUT clock divider by2" "0: CLKOUT divided by 1,1: CLKOUT divided by 2 (50/50 duty cycle)"
|
|
bitfld.long 0x0 24.--26. "PRECLKOUT,CLKOUT_CLK Prescaler Setting (based on selected clock by SELCLKOUT)" "0: clk divided by 1,1: clk divided by 2,2: clk divided by 3,3: clk divided by 4,4: clk divided by 5,5: clk divided by 8,6: clk divided by 16,7: clk divided by 20"
|
|
newline
|
|
bitfld.long 0x0 20.--22. "PREUART,UART_CLK Prescaler Setting (based on sys1_clk)" "0: clk divided by 1,1: clk divided by 2,2: clk divided by 3,3: clk divided by 4,4: clk divided by 5,5: clk divided by 8,6: clk divided by 16,7: clk divided by 20"
|
|
bitfld.long 0x0 16.--18. "PRECAN,CAN_CLK Prescaler Setting (based on sys1_clk)" "0: clk divided by 1,1: clk divided by 2,2: clk divided by 3,3: clk divided by 4,4: clk divided by 5,5: clk divided by 8,6: clk divided by 16,7: clk divided by 20"
|
|
newline
|
|
bitfld.long 0x0 9.--11. "PREMI,MI_CLK Prescaler Setting (based on sys0_clk)" "0: clk divided by 1,1: clk divided by 2,2: clk divided by 3,3: clk divided by 4,4: clk divided by 5,5: clk divided by 8,6: clk divided by 16,7: clk divided by 20"
|
|
hexmask.long.byte 0x0 4.--8. 1. "PREFILT,TFILT_CLK Prescaler Setting (based on sys0_clk)"
|
|
newline
|
|
bitfld.long 0x0 0.--2. "PRECPU,CPU_CLK Prescaler Setting (based on sys0_clk)" "0: clk divided by 1,1: clk divided by 2,2: clk divided by 3,3: clk divided by 4,4: clk divided by 5,5: clk divided by 8,6: clk divided by 16,7: clk_divided by 20"
|
|
line.long 0x4 "CLKEN,Peripheral Clock Enable Register"
|
|
bitfld.long 0x4 1. "CANCLKEN,CAN Clock Enable" "0: Clock disabled,1: Clock enabled"
|
|
bitfld.long 0x4 0. "UARTCLKEN,UART Clock Enable" "0: Clock disabled,1: Clock enabled"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CLKSEL,System Clock Select Register"
|
|
bitfld.long 0x0 19. "CLKOUTEN,CLKOUT Enable" "0: CLKOUT disabled,1: CLKOUT enabled"
|
|
bitfld.long 0x0 16.--18. "SELCLKOUT,CLKOUT Selection" "0: hp_clk selected as CLKOUT,1: xtal_clk selected as CLKOUT,2: pll0_clk selected as CLKOUT,3: pll1_clk selected as CLKOUT,4: cpu_clk selected as CLKOUT,5: m_clk selected as CLKOUT,6: ref_clk selected as CLKOUT,?"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "SELSYS1,System Clock fsys1 Select" "0: hp40_clk selected,1: xtal_clk selected,2: pll0_clk selected,3: pll1_clk selected"
|
|
bitfld.long 0x0 0.--1. "SELSYS0,System Clock fsys0 Select" "0: hp40_clk selected,1: xtal_clk selected,2: pll0_clk selected,3: pll1_clk selected"
|
|
group.long 0xE0++0x3
|
|
line.long 0x0 "DMACTRL,DMA Control Register"
|
|
bitfld.long 0x0 15. "DMAREQINTEN_CH7,DMA Pending Request Interrupt Enable Channel 7" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
bitfld.long 0x0 14. "DMAREQINTEN_CH6,DMA Pending Request Interrupt Enable Channel 6" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 13. "DMAREQINTEN_CH5,DMA Pending Request Interrupt Enable Channel 5" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
bitfld.long 0x0 12. "DMAREQINTEN_CH4,DMA Pending Request Interrupt Enable Channel 4" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 11. "DMAREQINTEN_CH3,DMA Pending Request Interrupt Enable Channel 3" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
bitfld.long 0x0 10. "DMAREQINTEN_CH2,DMA Pending Request Interrupt Enable Channel 2" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 9. "DMAREQINTEN_CH1,DMA Pending Request Interrupt Enable Channel 1" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
bitfld.long 0x0 8. "DMAREQINTEN_CH0,DMA Pending Request Interrupt Enable Channel 0" "0: Pending Request Interrupt disabled,1: Pending Request Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 7. "DEMEN_CH7,DMA Endless Mode Enable Channel 7" "0: Endless mode disabled,1: Endless mode enabled"
|
|
bitfld.long 0x0 6. "DEMEN_CH6,DMA Endless Mode Enable Channel 6" "0: Endless mode disabled,1: Endless mode enabled"
|
|
newline
|
|
bitfld.long 0x0 5. "DEMEN_CH5,DMA Endless Mode Enable Channel 5" "0: Endless mode disabled,1: Endless mode enabled"
|
|
bitfld.long 0x0 4. "DEMEN_CH4,DMA Endless Mode Enable Channel 4" "0: Endless mode disabled,1: Endless mode enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "DEMEN_CH3,DMA Endless Mode Enable Channel 3" "0: Endless mode disabled,1: Endless mode enabled"
|
|
bitfld.long 0x0 2. "DEMEN_CH2,DMA Endless Mode Enable Channel 2" "0: Endless mode disabled,1: Endless mode enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "DEMEN_CH1,DMA Endless Mode Enable Channel 1" "0: Endless mode disabled,1: Endless mode enabled"
|
|
bitfld.long 0x0 0. "DEMEN_CH0,DMA Endless Mode Enable Channel 0" "0: Endless mode disabled,1: Endless mode enabled"
|
|
group.long 0x8C++0x3
|
|
line.long 0x0 "DMAIEN,DMA Interrupt Enable Register"
|
|
bitfld.long 0x0 8. "DMATRERREN,DMA Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 7. "DMACH7EN,DMA Channel 7 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 6. "DMACH6EN,DMA Channel 6 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 5. "DMACH5EN,DMA Channel 5 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "DMACH4EN,DMA Channel 4 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 3. "DMACH3EN,DMA Channel 3 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "DMACH2EN,DMA Channel 2 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 1. "DMACH1EN,DMA Channel 1 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "DMACH0EN,DMA Channel 0 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x90++0x3
|
|
line.long 0x0 "DMAIS,DMA Interrupt Status Register"
|
|
bitfld.long 0x0 7. "DMACH7,DMA Channel 7 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 6. "DMACH6,DMA Channel 6 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 5. "DMACH5,DMA Channel 5 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "DMACH4,DMA Channel 4 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "DMACH3,DMA Channel 3 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "DMACH2,DMA Channel 2 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "DMACH1,DMA Channel 1 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "DMACH0,DMA Channel 0 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x94++0x7
|
|
line.long 0x0 "DMAISC,DAM Interrupt Status Clear Register"
|
|
bitfld.long 0x0 7. "DMACH7CLR,DMA Channel 7 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 6. "DMACH6CLR,DMA Channel 6 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "DMACH5CLR,DMA Channel 5 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "DMACH4CLR,DMA Channel 4 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "DMACH3CLR,DMA Channel 3 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "DMACH2CLR,DMA Channel 2 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "DMACH1CLR,DMA Channel 1 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "DMACH0CLR,DMA Channel 0 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
line.long 0x4 "DMAISS,DMA Interrupt Status Set Register"
|
|
bitfld.long 0x4 7. "DMACH7SET,DMA Channel 7 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 6. "DMACH6SET,DMA Channel 6 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 5. "DMACH5SET,DMA Channel 5 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 4. "DMACH4SET,DMA Channel 4 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 3. "DMACH3SET,DMA Channel 3 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 2. "DMACH2SET,DMA Channel 2 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 1. "DMACH1SET,DMA Channel 1 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 0. "DMACH0SET,DMA Channel 0 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0xA0++0x3
|
|
line.long 0x0 "DMAP_ADC,DMA Channel Select Register ADCs"
|
|
bitfld.long 0x0 26.--27. "SDADC_RES1,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 24.--25. "SDADC_RES0,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 22.--23. "ADC1_CMPHI,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 20.--21. "ADC1_CMPLO,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 18.--19. "ADC1_SQ1,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 16.--17. "ADC1_SQ0,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 14.--15. "ADC1_RES7,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 12.--13. "ADC1_RES6,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "ADC1_RES5,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 8.--9. "ADC1_RES4,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "ADC1_RES3,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 4.--5. "ADC1_RES2,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "ADC1_RES1,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected,2: Channel 5 selected,3: Channel 7 selected"
|
|
bitfld.long 0x0 0.--1. "ADC1_RES0,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected,2: Channel 4 selected,3: Channel 6 selected"
|
|
group.long 0x9C++0x3
|
|
line.long 0x0 "DMAP_CCU7,DMA Channel Select Register CCU7"
|
|
bitfld.long 0x0 28.--29. "CHE,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 26.--27. "T16PM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 24.--25. "T16CM,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 22.--23. "T15PM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 20.--21. "T15CM,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 18.--19. "T14PM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 16.--17. "T14CM,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 14.--15. "T13ZM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "T13PM,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 10.--11. "T13CM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 8.--9. "T12ZM,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 6.--7. "T12PM,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "T12CM72,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
bitfld.long 0x0 2.--3. "T12CM71,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: Channel 5 selected"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "T12CM70,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: Channel 4 selected"
|
|
group.long 0xA8++0x3
|
|
line.long 0x0 "DMAP_COM,DMA Channel Select Register COM Modules"
|
|
bitfld.long 0x0 18. "CAN_IR1,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected"
|
|
bitfld.long 0x0 16. "CAN_IR0,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected"
|
|
newline
|
|
bitfld.long 0x0 14.--15. "UART1_TI,DMA Channel Request Select" "0: No Channel selected,1: Channel 5 selected,2: Channel 7 selected,3: No Channel selected"
|
|
bitfld.long 0x0 12.--13. "UART1_RI,DMA Channel Request Select" "0: No Channel selected,1: Channel 4 selected,2: Channel 6 selected,3: No Channel selected"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "UART0_TI,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: No Channel selected"
|
|
bitfld.long 0x0 8.--9. "UART0_RI,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: No Channel selected"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "SSC1_TIR,DMA Channel Request Select" "0: No Channel selected,1: Channel 4 selected,2: Channel 6 selected,3: No Channel selected"
|
|
bitfld.long 0x0 4.--5. "SSC1_RIR,DMA Channel Request Select" "0: No Channel selected,1: Channel 5 selected,2: Channel 7 selected,3: No Channel selected"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "SSC0_TIR,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected,2: Channel 2 selected,3: No Channel selected"
|
|
bitfld.long 0x0 0.--1. "SSC0_RIR,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected,2: Channel 3 selected,3: No Channel selected"
|
|
group.long 0xA4++0x3
|
|
line.long 0x0 "DMAP_TIM,DMA Channel Select Register Timer"
|
|
bitfld.long 0x0 13. "GPT12CR,DMA Channel Request Select" "0: No Channel selected,1: Channel 5 selected"
|
|
bitfld.long 0x0 12. "GPT12T6,DMA Channel Request Select" "0: No Channel selected,1: Channel 4 selected"
|
|
newline
|
|
bitfld.long 0x0 11. "GPT12T5,DMA Channel Request Select" "0: No Channel selected,1: Channel 3 selected"
|
|
bitfld.long 0x0 10. "GPT12T4,DMA Channel Request Select" "0: No Channel selected,1: Channel 2 selected"
|
|
newline
|
|
bitfld.long 0x0 9. "GPT12T3,DMA Channel Request Select" "0: No Channel selected,1: Channel 1 selected"
|
|
bitfld.long 0x0 8. "GPT12T2,DMA Channel Request Select" "0: No Channel selected,1: Channel 0 selected"
|
|
newline
|
|
bitfld.long 0x0 1. "T21OV,DMA Channel Request Select" "0: No Channel selected,1: Channel 7 selected"
|
|
bitfld.long 0x0 0. "T2OV,DMA Channel Request Select" "0: No Channel selected,1: Channel 6 selected"
|
|
group.long 0x78++0x3
|
|
line.long 0x0 "EXTCON,EXT Interrupt Configuration Register"
|
|
bitfld.long 0x0 14.--15. "EXTINT3INSEL,External EXTINT3 Input Select" "0: EXTINT3A selected,1: EXTINT3B selected,2: EXTINT3C selected,3: EXTINT3D selected"
|
|
bitfld.long 0x0 12.--13. "EXTINT2INSEL,External EXTINT2 Input Select" "0: EXTINT2A selected,1: EXTINT2B selected,2: EXTINT2C selected,3: EXTINT2D selected"
|
|
newline
|
|
bitfld.long 0x0 10.--11. "EXTINT1INSEL,External EXTINT1 Input Select" "0: EXTINT1A selected,1: EXTINT1B selected,2: EXTINT1C selected,3: EXTINT1D selected"
|
|
bitfld.long 0x0 8.--9. "EXTINT0INSEL,External EXTINT0 Input Select" "0: EXTINT0A selected,1: EXTINT0B selected,2: EXTINT0C selected,3: EXTINT0D selected"
|
|
newline
|
|
bitfld.long 0x0 6.--7. "EXTINT3IEV,External EXTINT3Interrupt Event Select" "0: EXT Int disabled,1: EXT Int on rising edge,2: EXT Int on falling edge,3: EXT Int on both edges"
|
|
bitfld.long 0x0 4.--5. "EXTINT2IEV,External EXTINT2 Interrupt Event Select" "0: EXT Int disabled,1: EXT Int on rising edge,2: EXT Int on falling edge,3: EXT Int on both edges"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "EXTINT1IEV,External EXTINT1 Interrupt Event Select" "0: EXT Int disabled,1: EXT Int on rising edge,2: EXT Int on falling edge,3: EXT Int on both edges"
|
|
bitfld.long 0x0 0.--1. "EXTINT0IEV,External EXTINT0 Interrupt Event Select" "0: EXT Int disabled,1: EXT Int on rising edge,2: EXT Int on falling edge,3: EXT Int on both edges"
|
|
group.long 0x68++0x3
|
|
line.long 0x0 "EXTIEN,External Interrupt Enable Register"
|
|
bitfld.long 0x0 3. "EXTINT3EN,External EXTINT3 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 2. "EXTINT2EN,External EXTINT2 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "EXTINT1EN,External EXTINT1 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 0. "EXTINT0EN,External EXTINT0 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x6C++0x3
|
|
line.long 0x0 "EXTIS,External Interrupt Status Register"
|
|
bitfld.long 0x0 7. "EXTINT3F,External EXTINT3 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 6. "EXTINT3R,External EXTINT3 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 5. "EXTINT2F,External EXTINT2 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "EXTINT2R,External EXTINT2 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "EXTINT1F,External EXTINT1 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "EXTINT1R,External EXTINT1 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "EXTINT0F,External EXTINT0 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "EXTINT0R,External EXTINT0 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x70++0x7
|
|
line.long 0x0 "EXTISC,External Interrupt Status Clear Register"
|
|
bitfld.long 0x0 7. "EXTINT3FCLR,External EXTINT3 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 6. "EXTINT3RCLR,External EXTINT3 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "EXTINT2FCLR,External EXTINT2 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "EXTINT2RCLR,External EXTINT2 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "EXTINT1FCLR,External EXTINT1 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "EXTINT1RCLR,External EXTINT1 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "EXTINT0FCLR,External EXTINT0 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "EXTINT0RCLR,External EXTINT0 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
line.long 0x4 "EXTISS,External Interrupt Status Set Register"
|
|
bitfld.long 0x4 7. "EXTINT3FSET,External EXTINT3 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 6. "EXTINT3RSET,External EXTINT3 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 5. "EXTINT2FSET,External EXTINT2 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 4. "EXTINT2RSET,External EXTINT2 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 3. "EXTINT1FSET,External EXTINT1Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 2. "EXTINT1RSET,External EXTINT1Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 1. "EXTINT0FSET,External EXTINT0 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 0. "EXTINT0RSET,External EXTINT0 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0x7C++0x3
|
|
line.long 0x0 "GPTIEN,General Purpose Timer 12 Interrupt Enable Register"
|
|
bitfld.long 0x0 5. "GPT2CREN,General Purpose Timer 2 CR Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 4. "GPT2T6EN,General Purpose Timer 2 T6 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 3. "GPT2T5EN,General Purpose Timer 2 T5 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 2. "GPT1T4EN,General Purpose Timer 1 T4 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "GPT1T3EN,General Purpose Timer 1 T3 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 0. "GPT1T2EN,General Purpose Timer 1 T2 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x80++0x3
|
|
line.long 0x0 "GPTIS,General Purpose Timer 12 Interrupt Status Register"
|
|
bitfld.long 0x0 5. "GPT2CR,General Purpose Timer 2 CR Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "GPT2T6,General Purpose Timer 2 T6 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "GPT2T5,General Purpose Timer 2 T5 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "GPT1T4,General Purpose Timer 1 T4 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "GPT1T3,General Purpose Timer 1 T3 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "GPT1T2,General Purpose Timer 1 T2 Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x84++0x7
|
|
line.long 0x0 "GPTISC,General Purpose Timer 12 Interrupt Status Clear Register"
|
|
bitfld.long 0x0 5. "GPT2CRCLR,General Purpose Timer 2 CR Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "GPT2T6CLR,General Purpose Timer 2 T6 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "GPT2T5CLR,General Purpose Timer 2 T5 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "GPT1T4CLR,General Purpose Timer 1 T4 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "GPT1T3CLR,General Purpose Timer 1 T3 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "GPT1T2CLR,General Purpose Timer 1 T2 Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
line.long 0x4 "GPTISS,General Purpose Timer 12 Interrupt Status Set Register"
|
|
bitfld.long 0x4 5. "GPT2CRSET,General Purpose Timer 2 CR Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 4. "GPT2T6SET,General Purpose Timer 2 T6 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 3. "GPT2T5SET,General Purpose Timer 2 T5 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 2. "GPT1T4SET,General Purpose Timer 1 T4 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 1. "GPT1T3SET,General Purpose Timer 1 T3 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 0. "GPT1T2SET,General Purpose Timer 1 T2 Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0x24++0x1F
|
|
line.long 0x0 "INP0,Interrupt Node 0 Mapping Register"
|
|
bitfld.long 0x0 5. "INP_CSC,CSC Interrupt Mapping" "0: CSC INT mapped to IRQ0,1: CSC INT mapped to IRQ1"
|
|
bitfld.long 0x0 4. "INP_ARVG,ARVG Interrupt Mapping" "0: ARVG INT mapped to IRQ0,1: ARVG INT mapped to IRQ1"
|
|
newline
|
|
bitfld.long 0x0 3. "INP_CANTX,CANTX Interrupt Mapping" "0: CANTX INT mapped to IRQ0,1: CANTX INT mapped to IRQ1"
|
|
bitfld.long 0x0 2. "INP_BDRV_IRQ1,Bridge Driver Interrupt 1 Mapping" "0: BDRV_IRQ1 mapped to IRQ0,1: BDRV_IRQ1 mapped to IRQ1"
|
|
newline
|
|
bitfld.long 0x0 1. "INP_BDRV_IRQ0,Bridge Driver Interrupt 0 Mapping" "0: BDRV_IRQ0 mapped to IRQ0,1: BDRV_IRQ0 mapped to IRQ1"
|
|
bitfld.long 0x0 0. "INP_PMU,PMU Interrupt Mapping" "0: PMU INT mapped to IRQ0,1: PMU INT mapped to IRQ1"
|
|
line.long 0x4 "INP1,Interrupt Node 1 Mapping Register"
|
|
bitfld.long 0x4 5. "INP_GPT2CR,GPT2CR Interrupt Mapping" "0: GPT2CR INT mapped to IRQ7,1: GPT2CR INT mapped to IRQ8"
|
|
bitfld.long 0x4 4. "INP_GPT2T6,GPT2T6 Interrupt Mapping" "0: GPT2T6 INT mapped to IRQ7,1: GPT2T6 INT mapped to IRQ8"
|
|
newline
|
|
bitfld.long 0x4 3. "INP_GPT2T5,GPT2T5 Interrupt Mapping" "0: GPT2T5 INT mapped to IRQ7,1: GPT2T5 INT mapped to IRQ8"
|
|
bitfld.long 0x4 2. "INP_GPT1T4,GPT1T4 Interrupt Mapping" "0: GPT1T4 INT mapped to IRQ7,1: GPT1T4 INT mapped to IRQ8"
|
|
newline
|
|
bitfld.long 0x4 1. "INP_GPT1T3,GPT1T3 Interrupt Mapping" "0: GPT1T3 INT mapped to IRQ7,1: GPT1T3 INT mapped to IRQ8"
|
|
bitfld.long 0x4 0. "INP_GPT1T2,GPT1T2 Interrupt Mapping" "0: GPT1T2 INT mapped to IRQ7,1: GPT1T2 INT mapped to IRQ8"
|
|
line.long 0x8 "INP2,Interrupt Node 2 Mapping Register"
|
|
bitfld.long 0x8 2. "INP_MON3,MON3 Interrupt Mapping" "0: MON3 INT mapped to IRQ12,1: MON3 INT mapped to IRQ13"
|
|
bitfld.long 0x8 1. "INP_MON2,MON2 Interrupt Mapping" "0: MON2 INT mapped to IRQ12,1: MON2 INT mapped to IRQ13"
|
|
newline
|
|
bitfld.long 0x8 0. "INP_MON1,MON1 Interrupt Mapping" "0: MON1 INT mapped to IRQ12,1: MON1 INT mapped to IRQ13"
|
|
line.long 0xC "INP3,Interrupt Node 3 Mapping Register"
|
|
bitfld.long 0xC 4. "INP_BEMF2,BEMF2 Interrupt Mapping" "0: BEMF2 INT mapped to IRQ18,1: BEMF2 INT mapped to IRQ19"
|
|
bitfld.long 0xC 3. "INP_BEMF1,BEMF1 Interrupt Mapping" "0: BEMF1 INT mapped to IRQ18,1: BEMF1 INT mapped to IRQ19"
|
|
newline
|
|
bitfld.long 0xC 2. "INP_BEMF0,BEMF0 Interrupt Mapping" "0: BEMF0 INT mapped to IRQ18,1: BEMF0 INT mapped to IRQ19"
|
|
bitfld.long 0xC 1. "INP_SDADC1,SDADC1 Interrupt Mapping" "0: SDADC1 INT mapped to IRQ18,1: SDADC1 INT mapped to IRQ19"
|
|
newline
|
|
bitfld.long 0xC 0. "INP_SDADC0,SDADC0 Interrupt Mapping" "0: SDADC0 INT mapped to IRQ18,1: SDADC0 INT mapped to IRQ19"
|
|
line.long 0x10 "INP4,Interrupt Node 4 Mapping Register"
|
|
bitfld.long 0x10 3. "INP_EXINT3,EXINT3 Interrupt Mapping" "0: EXINT3 INT mapped to IRQ20,1: EXINT3 INT mapped to IRQ21"
|
|
bitfld.long 0x10 2. "INP_EXINT2,EXINT2 Interrupt Mapping" "0: EXINT2 INT mapped to IRQ20,1: EXINT2 INT mapped to IRQ21"
|
|
newline
|
|
bitfld.long 0x10 1. "INP_EXINT1,EXINT1 Interrupt Mapping" "0: EXINT1 INT mapped to IRQ20,1: EXINT1 INT mapped to IRQ21"
|
|
bitfld.long 0x10 0. "INP_EXINT0,EXINT0 Interrupt Mapping" "0: EXINT0 INT mapped to IRQ20,1: EXINT0 INT mapped to IRQ21"
|
|
line.long 0x14 "INP5,Interrupt Node 5 Mapping Register"
|
|
bitfld.long 0x14 7. "INP_UART1_TI,UART1_TI Interrupt Mapping" "0: UART1_TI INT mapped to IRQ22,1: UART1_TI INT mapped to IRQ23"
|
|
bitfld.long 0x14 6. "INP_UART1_RI,UART1_RI Interrupt Mapping" "0: UART1_RI INT mapped to IRQ22,1: UART1_RI INT mapped to IRQ23"
|
|
newline
|
|
bitfld.long 0x14 5. "INP_UART0_TI,UART0_TI Interrupt Mapping" "0: UART0_TI INT mapped to IRQ22,1: UART0_TI INT mapped to IRQ23"
|
|
bitfld.long 0x14 4. "INP_UART0_RI,UART0_RI Interrupt Mapping" "0: UART0_RI INT mapped to IRQ22,1: UART0_RI INT mapped to IRQ23"
|
|
newline
|
|
bitfld.long 0x14 3. "INP_LIN1_ERRSYN,LIN1_ERRSYN Interrupt Mapping" "0: LIN1_ERRSYN INT mapped to IRQ22,1: LIN1_ERRSYN INT mapped to IRQ23"
|
|
bitfld.long 0x14 2. "INP_LIN1_EOFSYN,LIN1_EOFSYN Interrupt Mapping" "0: LIN1_EOFSYN INT mapped to IRQ22,1: LIN1_EOFSYN INT mapped to IRQ23"
|
|
newline
|
|
bitfld.long 0x14 1. "INP_LIN0_ERRSYN,LIN0_ERRSYN Interrupt Mapping" "0: LIN0_ERRSYN INT mapped to IRQ22,1: LIN0_ERRSYN INT mapped to IRQ23"
|
|
bitfld.long 0x14 0. "INP_LIN0_EOFSYN,LIN0_EOFSYN Interrupt Mapping" "0: LIN0_EOFSYN INT mapped to IRQ22,1: LIN0_EOFSYN INT mapped to IRQ23"
|
|
line.long 0x18 "INP6,Interrupt Node 6 Mapping Register"
|
|
bitfld.long 0x18 6. "INP_SSC1_EIR,SSC1_EIR Interrupt Mapping" "0: SSC1_EIR INT mapped to IRQ24,1: SSC1_EIR INT mapped to IRQ25"
|
|
bitfld.long 0x18 5. "INP_SSC1_TIR,SSC1_TIR Interrupt Mapping" "0: SSC1_TIR INT mapped to IRQ24,1: SSC1_TIR INT mapped to IRQ25"
|
|
newline
|
|
bitfld.long 0x18 4. "INP_SSC1_RIR,SSC1_RIR Interrupt Mapping" "0: SSC1_RIR INT mapped to IRQ24,1: SSC1_RIR INT mapped to IRQ25"
|
|
bitfld.long 0x18 2. "INP_SSC0_EIR,SSC0_EIR Interrupt Mapping" "0: SSC0_EIR INT mapped to IRQ24,1: SSC0_EIR INT mapped to IRQ25"
|
|
newline
|
|
bitfld.long 0x18 1. "INP_SSC0_TIR,SSC0_TIR Interrupt Mapping" "0: SSC0_TIR INT mapped to IRQ24,1: SSC0_TIR INT mapped to IRQ25"
|
|
bitfld.long 0x18 0. "INP_SSC0_RIR,SSC0_RIR Interrupt Mapping" "0: SSC0_RIR INT mapped to IRQ24,1: SSC0_RIR INT mapped to IRQ25"
|
|
line.long 0x1C "INP7,Interrupt Node 7 Mapping Register"
|
|
bitfld.long 0x1C 8. "INP_DMATRERR,DMATRERR Interrupt Mapping" "0: DMATRERR INT mapped to IRQ29,1: DMATRERR INT mapped to IRQ30"
|
|
bitfld.long 0x1C 7. "INP_DMACH7,DMACH7 Interrupt Mapping" "0: DMACH7 INT mapped to IRQ29,1: DMACH7 INT mapped to IRQ30"
|
|
newline
|
|
bitfld.long 0x1C 6. "INP_DMACH6,DMACH6 Interrupt Mapping" "0: DMACH6 INT mapped to IRQ29,1: DMACH6 INT mapped to IRQ30"
|
|
bitfld.long 0x1C 5. "INP_DMACH5,DMACH5 Interrupt Mapping" "0: DMACH5 INT mapped to IRQ29,1: DMACH5 INT mapped to IRQ30"
|
|
newline
|
|
bitfld.long 0x1C 4. "INP_DMACH4,DMACH4 Interrupt Mapping" "0: DMACH4 INT mapped to IRQ29,1: DMACH4 INT mapped to IRQ30"
|
|
bitfld.long 0x1C 3. "INP_DMACH3,DMACH3 Interrupt Mapping" "0: DMACH3 INT mapped to IRQ29,1: DMACH3 INT mapped to IRQ30"
|
|
newline
|
|
bitfld.long 0x1C 2. "INP_DMACH2,DMACH2 Interrupt Mapping" "0: DMACH2 INT mapped to IRQ29,1: DMACH2 INT mapped to IRQ30"
|
|
bitfld.long 0x1C 1. "INP_DMACH1,DMACH1 Interrupt Mapping" "0: DMACH1 INT mapped to IRQ29,1: DMACH1 INT mapped to IRQ30"
|
|
newline
|
|
bitfld.long 0x1C 0. "INP_DMACH0,DMACH0 Interrupt Mapping" "0: DMACH0 INT mapped to IRQ29,1: DMACH0 INT mapped to IRQ30"
|
|
group.long 0xE8++0x3
|
|
line.long 0x0 "LOCKUPCFG,CPU LOCKUP Config Register"
|
|
bitfld.long 0x0 0. "LOCKUP_EN,CPU LOCKUP Reset Enable" "0: CPU LOCKUP Reset Disabled,1: CPU LOCKUP Reset Enabled"
|
|
group.long 0x64++0x3
|
|
line.long 0x0 "MONCON,MON Interrupt Configuration Register"
|
|
bitfld.long 0x0 4.--5. "MON3IEV,MON3 Interrupt Event Select" "0: MON Int disabled,1: MON Int on rising edge,2: MON Int on falling edge,3: MON Int on both edges"
|
|
bitfld.long 0x0 2.--3. "MON2IEV,MON2 Interrupt Event Select" "0: MON Int disabled,1: MON Int on rising edge,2: MON Int on falling edge,3: MON Int on both edges"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "MON1IEV,MON1 Interrupt Event Select" "0: MON Int disabled,1: MON Int on rising edge,2: MON Int on falling edge,3: MON Int on both edges"
|
|
group.long 0x54++0x3
|
|
line.long 0x0 "MONIEN,MON Interrupt Enable Register"
|
|
bitfld.long 0x0 2. "MON3EN,MON3 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 1. "MON2EN,MON2 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "MON1EN,MON1 Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
rgroup.long 0x58++0x3
|
|
line.long 0x0 "MONIS,MON Interrupt Status Register"
|
|
bitfld.long 0x0 5. "MON3F,MON3 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "MON3R,MON3 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "MON2F,MON2 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "MON2R,MON2 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "MON1F,MON1 Falling Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "MON1R,MON1 Rising Edge Interrupt Status" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x5C++0x7
|
|
line.long 0x0 "MONISC,MON Interrupt Status Clear Register"
|
|
bitfld.long 0x0 5. "MON3FCLR,MON3 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "MON3RCLR,MON3 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "MON2FCLR,MON2 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "MON2RCLR,MON2 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "MON1FCLR,MON1 Falling Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "MON1RCLR,MON1 Rising Edge Interrupt Status Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
line.long 0x4 "MONISS,MON Interrupt Status Set Register"
|
|
bitfld.long 0x4 5. "MON3FSET,MON3 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 4. "MON3RSET,MON3 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 3. "MON2FSET,MON2 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 2. "MON2RSET,MON2 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
newline
|
|
bitfld.long 0x4 1. "MON1FSET,MON1 Falling Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
bitfld.long 0x4 0. "MON1RSET,MON1 Rising Edge Interrupt Status Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0x44++0x3
|
|
line.long 0x0 "NMICON,NMI Control Register"
|
|
bitfld.long 0x0 2. "NMIPLL1EN,PLL1 Loss of Lock NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
bitfld.long 0x0 1. "NMIPLL0EN,PLL0 Loss of Lock NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIXTALEN,XTAL Watchdog Fail NMI Enable" "0: NMI disabled,1: NMI enabled"
|
|
rgroup.long 0x48++0x3
|
|
line.long 0x0 "NMISR,NMI Status Register"
|
|
bitfld.long 0x0 2. "NMIPLL1,PLL1 Loss of Lock NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
bitfld.long 0x0 1. "NMIPLL0,PLL0 Loss of Lock NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIXTAL,XTAL Watchdog Fail NMI Status" "0: NMI not occurred,1: NMI occurred"
|
|
wgroup.long 0x4C++0x7
|
|
line.long 0x0 "NMISRC,NMI Status Clear Register"
|
|
bitfld.long 0x0 2. "NMIPLL1CLR,PLL1 Loss of Lock NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
bitfld.long 0x0 1. "NMIPLL0CLR,PLL0 Loss of Lock NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
newline
|
|
bitfld.long 0x0 0. "NMIXTALCLR,XTAL Watchdog Fail NMI Status Clear" "0: NMI not cleared,1: NMI cleared"
|
|
line.long 0x4 "NMISRS,NMI Status Set Register"
|
|
bitfld.long 0x4 2. "NMIPLL1SET,PLL1 Loss of Lock NMI Status Set" "0: NMI not set,1: NMI set"
|
|
bitfld.long 0x4 1. "NMIPLL0SET,PLL0 Loss of Lock NMI Status Set" "0: NMI not set,1: NMI set"
|
|
newline
|
|
bitfld.long 0x4 0. "NMIXTALSET,XTAL Watchdog Fail NMI Status Set" "0: NMI not set,1: NMI set"
|
|
group.long 0xB8++0x3
|
|
line.long 0x0 "PCU_CTRL,PCU Control Register"
|
|
bitfld.long 0x0 24. "BDRV_SD_EN,BDRV Shutdown Enable" "0: Shutdown disabled,1: Shutdown enabled"
|
|
bitfld.long 0x0 15. "XTALWDG_SD_DIS,XTAL Watchdog Peripherals Shutdown Disable" "0: Shutdown of selected peripherals enabled,1: Shutdown of selected peripherals disabled"
|
|
newline
|
|
bitfld.long 0x0 14. "OTWARN_SD_DIS,Overtemperature Warning Peripherals Shutdown Disable" "0: Shutdown of selected peripherals enabled,1: Shutdown of selected peripherals disabled"
|
|
bitfld.long 0x0 0. "OT_SLEEP_EN,System Overtemperature Sleep Mode Enable" "0: No Sleep Mode in case of SysOT,1: Sleep Mode in case of SysOT"
|
|
group.long 0xB0++0x3
|
|
line.long 0x0 "PMCON,Peripheral Management Control Register"
|
|
bitfld.long 0x0 4. "GPT12_DIS,General Purpose Timer 12 Module Disable" "0: GPT12 enabled (normal operation mode),1: GPT12 disabled"
|
|
bitfld.long 0x0 3. "T21_DIS,Timer 21 Module Disable" "0: T21 enable (normal operation mode),1: T21 disabled"
|
|
newline
|
|
bitfld.long 0x0 2. "T2_DIS,Timer 20 Module Disable" "0: T2 enabled (normal operation mode),1: T2 disabled"
|
|
bitfld.long 0x0 1. "SSC1_DIS,SSC1 Module Disable" "0: SSC1 enabled (normal operation mode),1: SSC1 disabled"
|
|
newline
|
|
bitfld.long 0x0 0. "SSC0_DIS,SSC0 Module Disable" "0: SSC0 enabled (normal operation mode),1: SSC0 disabled"
|
|
wgroup.long 0xAC++0x3
|
|
line.long 0x0 "PMCON0,Power Mode Control Register"
|
|
bitfld.long 0x0 2. "STOP,STOP Mode Enable" "0: Active Mode,1: STOP Mode Entry"
|
|
bitfld.long 0x0 1. "SLEEP,Sleep Mode Enable" "0: Active Mode,1: SLEEP Mode Entry"
|
|
group.long 0xB4++0x3
|
|
line.long 0x0 "SUSCTR,Module Suspend Control Register"
|
|
bitfld.long 0x0 5. "WDTSUS,SCU Watchdog Timer Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
bitfld.long 0x0 4. "GPT12SUS,Gerneral Purpose Timer 12 Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
newline
|
|
bitfld.long 0x0 3. "T21SUS,Timer 21 Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
bitfld.long 0x0 2. "T2SUS,Timer 20 Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
newline
|
|
bitfld.long 0x0 1. "SSC1SUS,SSC1 Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
bitfld.long 0x0 0. "SSC0SUS,SSC0 Suspend" "0: module continues on DBG request,1: module suspended on DBG request"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "XTALCON,XTAL Control Register"
|
|
bitfld.long 0x0 28. "XWDGRES,XTALWDG Reset" "0: XTALWDG not reset,1: XTALWDG reset"
|
|
bitfld.long 0x0 24. "XWDGEN,XTALWDG Enable" "0: XTALWDG disabled,1: XTALWDG enabled"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "XTALHYS,XTAL Hysteresis Control" "0: high hysteresis slow filter,1: medium hysteresis medium filter,2: low hysteresis fast filter,3: very low hysteresis filter off"
|
|
bitfld.long 0x0 1. "XTALHYSEN,XTAL Hysteresis Enable" "0: lowest hysteresis filter off,1: see values according to XTALHYS setting"
|
|
newline
|
|
bitfld.long 0x0 0. "XPD,XTAL Power Down Control" "0: XTAL is powered,1: XTAL power down"
|
|
rgroup.long 0x18++0x3
|
|
line.long 0x0 "XTALSTAT,XTAL Status Register"
|
|
bitfld.long 0x0 8. "XTALFAIL,XTAL Watchdog Fail Current Status" "0: XTAL Clock is OK,1: XTAL Clock Fail"
|
|
bitfld.long 0x0 0. "XTAL_FAIL_STS,XTAL Watchdog Fail Latched Status" "0: XTAL Clock is OK,1: XTAL Clock Fail"
|
|
wgroup.long 0x1C++0x7
|
|
line.long 0x0 "XTALSTATC,XTAL Status Clear Register"
|
|
bitfld.long 0x0 0. "XTAL_FAIL_STSCLR,XTAL Watchdog Fail Latched Status Clear" "0: Status not cleared,1: Status cleared"
|
|
line.long 0x4 "XTALSTATS,XTAL Status Set Register"
|
|
bitfld.long 0x4 0. "XTAL_FAIL_STSSET,XTAL Watchdog Fail Latched Status Set" "0: Status not Set,1: Status Set"
|
|
tree.end
|
|
tree "SDADC (14-bit Sigma Delta Analog/Digital Converter)"
|
|
base ad:0x40004000
|
|
group.long 0x8++0x3
|
|
line.long 0x0 "ALTSEL,Alternate function selection"
|
|
bitfld.long 0x0 8.--9. "DOUT1,DOUT1 mapping" "0: DOUT0 output is off,1: Channel 0 analog modulator output available at..,2: Channel 1 analog modulator output available at..,?"
|
|
bitfld.long 0x0 4.--5. "DOUT0,DOUT0 mapping" "0: DOUT0 output is off,1: Channel 0 analog modulator output available at..,2: Channel 1 analog modulator output available at..,?"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "MCLK,MCLK output mapping" "0: MCLK output is off,1: MCLK connected to MCLK0,2: MCLK connected to MCLK1,?"
|
|
group.long 0x0++0x7
|
|
line.long 0x0 "CFG0,Configuration Register 0"
|
|
bitfld.long 0x0 19. "DITHEREN,Dithering of SD ADC Clock for channel 0/1" "0: Dithering disabled,1: Dithering enabled"
|
|
bitfld.long 0x0 16.--18. "PRE,Prescaler for Modulator and CIC clock" "0: fsdadc / 1,1: fsdadc / 2,2: fsdadc / 3,3: fsdadc / 4,4: fsdadc / 5,5: fsdadc / 6,6: fsdadc / 7,7: fsdadc / 8"
|
|
newline
|
|
bitfld.long 0x0 10. "WFREN1,Wait for Read of Result Register Channel 1" "0: Result Register is overwritten regardless if it..,1: Wait for read is enabled; Result Register is not.."
|
|
bitfld.long 0x0 9. "CICMODE1,CIC Filter Mode channel 1" "0: Continuous Mode - CIC Filter is clocked when EN1..,1: Triggered Mode - CIC Filter starts with External.."
|
|
newline
|
|
bitfld.long 0x0 8. "EN1,Enable Channel 1" "0: Channel 1 is disabled,1: Channel 1 is enabled"
|
|
bitfld.long 0x0 2. "WFREN0,Wait for Read of Result Register Channel 0" "0: Result Register is overwritten regardless if it..,1: Wait for read is enabled; Result Register is not.."
|
|
newline
|
|
bitfld.long 0x0 1. "CICMODE0,CIC Filter Mode channel 0" "0: Continuous Mode - CIC Filter is clocked when EN0..,1: Triggered Mode - CIC Filter starts with External.."
|
|
bitfld.long 0x0 0. "EN0,Enable Channel 0" "0: Channel 0 is disabled,1: Channel 0 is enabled"
|
|
line.long 0x4 "CFG1,Configuration Register 1"
|
|
hexmask.long.byte 0x4 28.--31. 1. "RESSHIFT1,Result Left shift channel 1"
|
|
hexmask.long.word 0x4 16.--24. 1. "DECF1,Decimation factor channel 1"
|
|
newline
|
|
hexmask.long.byte 0x4 12.--15. 1. "RESSHIFT0,Result Left shift channel 0"
|
|
hexmask.long.word 0x4 0.--8. 1. "DECF0,Decimation Factor channel 0"
|
|
group.long 0x2C++0x7
|
|
line.long 0x0 "CMP0_CTRL,Compare Channel 0 Control Register"
|
|
bitfld.long 0x0 30.--31. "MODE,Compare Mode channel 0" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x0 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold channel 0" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
hexmask.long.word 0x0 16.--24. 1. "UPPER,Upper Compare Level for channel 0"
|
|
bitfld.long 0x0 14.--15. "UPLO_OUTSEL,Signal output selection for UPLO output of channel 0" "0: Output OR-Combination of UP/LO signal,1: Output XOR-Combination of UP/LO signal,2: Output UP signal,3: Output LO signal"
|
|
newline
|
|
bitfld.long 0x0 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold channel 0" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
hexmask.long.word 0x0 0.--8. 1. "LOWER,Lower Compare Level for channel 0"
|
|
line.long 0x4 "CMP1_CTRL,Compare Channel 1 Control Register"
|
|
bitfld.long 0x4 30.--31. "MODE,Compare Mode channel 1" "0: Upper and Lower voltage/limit measurement,1: undervoltage/-limit measurement,2: overvoltage/-limit measurement,?"
|
|
bitfld.long 0x4 28.--29. "HYST_UP,Hysteresis setting for upper compare threshold channel 1" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
newline
|
|
hexmask.long.word 0x4 16.--24. 1. "UPPER,Upper Compare Level for channel 1"
|
|
bitfld.long 0x4 14.--15. "UPLO_OUTSEL,Signal output selection for UPLO output of channel 1" "0: Output OR-Combination of UP/LO signal,1: Output XOR-Combination of UP/LO signal,2: Output UP signal,3: Output LO signal"
|
|
newline
|
|
bitfld.long 0x4 12.--13. "HYST_LO,Hysteresis setting for lower compare threshold channel 1" "0: OFF,1: Hysteresis=4,2: Hysteresis=8,3: Hysteresis=16"
|
|
hexmask.long.word 0x4 0.--8. 1. "LOWER,Lower Compare Level for channel 1"
|
|
rgroup.long 0x3C++0x7
|
|
line.long 0x0 "CTIM0,Captured Timestamp channel 0"
|
|
hexmask.long.word 0x0 0.--8. 1. "TIMVAL,Captured Timestamp Value"
|
|
line.long 0x4 "CTIM1,Captured Timestamp channel 1"
|
|
hexmask.long.word 0x4 0.--8. 1. "TIMVAL,Captured Timestamp Value"
|
|
group.long 0x44++0x3
|
|
line.long 0x0 "DITHCFG,Dither Configuration Register"
|
|
hexmask.long.byte 0x0 0.--3. 1. "DITH_VOLT_SEL,Dither voltage Selection"
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "IEN,Interrupt Enable Register"
|
|
bitfld.long 0x0 6. "CMP1_LO_EN,Lower compare level Interrupt channel 1" "0: Lower compare Interrupt disabled,1: Lower compare Interrupt enabled"
|
|
bitfld.long 0x0 5. "CMP1_UP_EN,Upper Compare Level Interrupt channel 1" "0: Upper compare Interrupt disabled,1: Upper compare Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 4. "RES1_EN,Result interrupt channel 1" "0: Result Interrupt disabled,1: Result Interrupt enabled"
|
|
bitfld.long 0x0 2. "CMP0_LO_EN,Lower compare level Interrupt channel 0" "0: Lower compare Interrupt disabled,1: Lower compare Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP0_UP_EN,Upper Compare Level Interrupt channel 0" "0: Upper compare Interrupt disabled,1: Upper compare Interrupt enabled"
|
|
bitfld.long 0x0 0. "RES0_EN,Result interrupt channel 0" "0: Result Interrupt disabled,1: Result Interrupt enabled"
|
|
group.long 0x20++0x3
|
|
line.long 0x0 "INP,Interrupt Node Pointer"
|
|
bitfld.long 0x0 6. "CMP1_LO_INP,Lower Compare Level Interupt Pointer channel 1" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
bitfld.long 0x0 5. "CMP1_UP_INP,Upper Compare Level Interupt Pointer channel 1" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
newline
|
|
bitfld.long 0x0 4. "RES1_INP,Result Interupt Node Pointer channel 1" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
bitfld.long 0x0 2. "CMP0_LO_INP,Lower Compare Level Interupt Pointer channel 0" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP0_UP_INP,Upper Compare Level Interupt Pointer channel 0" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
bitfld.long 0x0 0. "RES0_INP,Result Interupt Node Pointer channel 0" "0: mapped to IRQ0,1: mapped to IRQ1"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "INSEL,Input Port Selection"
|
|
bitfld.long 0x0 22. "TRG1SEL,Trigger Event Selection" "0: Event TRG1SDA is selected,1: Event TRG1SDB is selected"
|
|
bitfld.long 0x0 20.--21. "DIN1SEL,External Digital Input Selection 1" "0: from Modulator channel 1,1: DIN1A,2: DIN1B,?"
|
|
newline
|
|
bitfld.long 0x0 18.--19. "IN1NSEL,INN Input Select 1" "0: Input disconnected; internally connected to VDD/2,1: Input connected to IN1NA,2: Input connected to IN1NB,3: Input connected to GND"
|
|
bitfld.long 0x0 16.--17. "IN1PSEL,Selection for positive analog input of channel 0" "0: Input disconnected; internally connected to VDD/2,1: Input connected to IN1PA,2: Input connected to IN1PB,?"
|
|
newline
|
|
bitfld.long 0x0 6. "TRG0SEL,Trigger Event Selection" "0: Event TRG0SDA is selected,1: Event TRG0SDB is selected"
|
|
bitfld.long 0x0 4.--5. "DIN0SEL,Selection of digital input of channel 0" "0: from Modulator channel 0,1: DIN0A,2: DIN0B,?"
|
|
newline
|
|
bitfld.long 0x0 2.--3. "IN0NSEL,Selection for negative analog input of channel 0" "0: Input disconnected,1: Input connected to IN0NA,2: Input connected to IN0NB,3: Input connected to GND"
|
|
bitfld.long 0x0 0.--1. "IN0PSEL,Selection for positive analog input of channel 0" "0: Input disconnected; internally connected to VDD/2,1: Input connected to IN0PA,2: Input connected to IN0PB,?"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "IS,Event Register"
|
|
bitfld.long 0x0 6. "CMP1_LO_IS,Lower compare level interupt channel 1" "0: Interrupt has not occured,1: Interrupt occured"
|
|
bitfld.long 0x0 5. "CMP1_UP_IS,Upper Compare level Interupt channel 1" "0: Interrupt has not occured,1: Interrupt occured"
|
|
newline
|
|
bitfld.long 0x0 4. "RES1_IS,Result interupt channel 1" "0: Interrupt has not occured,1: Interrupt occured"
|
|
bitfld.long 0x0 2. "CMP0_LO_IS,Lower compare level interupt channel 0" "0: Interrupt has not occured,1: Interrupt occured"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP0_UP_IS,Upper Compare level Interupt channel 0" "0: Interrupt has not occured,1: Interrupt occured"
|
|
bitfld.long 0x0 0. "RES0_IS,Result Interupt channel 0" "0: Interrupt has not occured,1: Interrupt occured"
|
|
wgroup.long 0x18++0x7
|
|
line.long 0x0 "ISR,Event Clear Register"
|
|
bitfld.long 0x0 6. "CMP1_LO_ISC,Lower Compare Level Interupt clear channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x0 5. "CMP1_UP_ISC,Upper Compare Level Interupt clear channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
newline
|
|
bitfld.long 0x0 4. "RES1_ISC,Result Interupt clear channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x0 2. "CMP0_LO_ISC,Lower Compare Level Interupt clear channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "CMP0_UP_ISC,Upper Compare Level Interupt clear channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x0 0. "RES0_ISC,Result Interupt clear channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
line.long 0x4 "ISS,Event Set Register"
|
|
bitfld.long 0x4 6. "CMP1_LO_ISS,Lower Compare Level Interupt set channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x4 5. "CMP1_UP_ISS,Upper Compare Level Interupt set channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
newline
|
|
bitfld.long 0x4 4. "RES1_ISS,Result Interupt set channel 1" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x4 2. "CMP0_LO_ISS,Lower Compare Level Interrupt set channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
newline
|
|
bitfld.long 0x4 1. "CMP0_UP_ISS,Upper Compare Level Interupt set channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
bitfld.long 0x4 0. "RES0_ISS,Result Interupt set channel 0" "0: Interrupt Status flag not cleared,1: Interrupt status flag cleared"
|
|
rgroup.long 0x34++0x7
|
|
line.long 0x0 "RES0,Result Register channel 0"
|
|
bitfld.long 0x0 31. "RESVALID,Result valid" "0: The result Register has not been updated,1: The result Register has been updated"
|
|
bitfld.long 0x0 28.--30. "VALCNT,Valid Counter" "0,1,2,3,4,5,6,7"
|
|
newline
|
|
hexmask.long.word 0x0 16.--24. 1. "TIMVAL,Timestamp Value"
|
|
hexmask.long.word 0x0 0.--15. 1. "RESULT,Result Register 2s complement"
|
|
line.long 0x4 "RES1,Result Register channel 1"
|
|
bitfld.long 0x4 31. "RESVALID,Result valid" "0: The result Register has not been updated,1: The result Register has been updated"
|
|
bitfld.long 0x4 28.--30. "VALCNT,Valid Counter" "0,1,2,3,4,5,6,7"
|
|
newline
|
|
hexmask.long.word 0x4 16.--24. 1. "TIMVAL,Timestamp Value"
|
|
hexmask.long.word 0x4 0.--15. 1. "RESULT,Result Register 2s complement"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "STS,Status Register"
|
|
bitfld.long 0x0 7. "WFR1_STS,Result discarded channel 1" "0,1"
|
|
bitfld.long 0x0 6. "CMP1_LO_STS,Lower compare level Status channel 1" "0: Interupt has not occured,1: Interupt occured"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP1_UP_STS,Upper Compare level Status channel 1" "0: Interupt has not occured,1: Interupt occured"
|
|
bitfld.long 0x0 3. "WFR0_STS,Result discarded channel 0" "0,1"
|
|
newline
|
|
bitfld.long 0x0 2. "CMP0_LO_STS,Lower compare level Status channel 0" "0: Interupt has not occured,1: Interupt occured"
|
|
bitfld.long 0x0 1. "CMP0_UP_STS,Upper Compare level Status channel 0" "0: Interupt has not occured,1: Interupt occured"
|
|
wgroup.long 0x4C++0x3
|
|
line.long 0x0 "STSR,Status Clear Register"
|
|
bitfld.long 0x0 7. "WFR1_SC,Wait for Read Status clear channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 6. "CMP1_LO_SC,Lower compare level Status clear channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP1_UP_SC,Upper Compare level Status clear channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 3. "WFR0_SC,Wait for Read Status clear channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "CMP0_LO_SC,Lower compare level Status clear channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 1. "CMP0_UP_SC,Upper Compare level Status clear channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
wgroup.long 0x54++0x3
|
|
line.long 0x0 "STSS,Status Set Register"
|
|
bitfld.long 0x0 7. "WFR1_SS,Wait for Read Status set channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 6. "CMP1_LO_SS,Lower compare level Status set channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
newline
|
|
bitfld.long 0x0 5. "CMP1_UP_SS,Upper Compare level Status set channel 1" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 3. "WFR0_SS,Wait for Read Status set channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
newline
|
|
bitfld.long 0x0 2. "CMP0_LO_SS,Lower compare level Status set channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
bitfld.long 0x0 1. "CMP0_UP_SS,Upper Compare level Status set channel 0" "0: Interupt is not cleared,1: Interupt is cleared"
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "SUSCTR,Suspend Control"
|
|
bitfld.long 0x0 0. "EN,Suspend Mode Enable" "0: Entering Suspend Mode is disabled,1: Entering Suspend Mode is enabled"
|
|
rgroup.long 0x28++0x3
|
|
line.long 0x0 "SUSSTAT,Suspend Status"
|
|
bitfld.long 0x0 0. "STAT,Suspend Status" "0: SD ADC is not suspended,1: SD ADC is suspended"
|
|
tree.end
|
|
tree "SSC (High-Speed Synchronous Serial Channel)"
|
|
base ad:0x0
|
|
tree "SSC0"
|
|
base ad:0x48020000
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "BR,Baud Rate Timer Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "BR_VALUE,Baud Rate Timer Value"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CON,Control Register"
|
|
bitfld.long 0x0 23.--24. "MSTXENSEL,Master Mode Transmit Start Trigger Select" "0: Write to TB0,1: Set MSTXSTART,2: Rising edge on selected input,?"
|
|
bitfld.long 0x0 22. "MSTXSTART,Master Mode Transmit Start Bit" "0: No Data Transmission,1: Software Start Event"
|
|
newline
|
|
hexmask.long.byte 0x0 18.--21. 1. "MSCSSEL,Master Chip Select Output Selection"
|
|
bitfld.long 0x0 17. "MSCSEN,Master Chip Select Enable" "0: No master chip select is used,1: The selected CSx is used as master chip select"
|
|
newline
|
|
bitfld.long 0x0 16. "SLCSEN,Slave Chip Select Enable" "0: No slave chip select is used,1: SLS input is used as slave chip select"
|
|
bitfld.long 0x0 15. "EN,Enable Bit" "0: SSC Module disabled,1: SSC Module enabled"
|
|
newline
|
|
bitfld.long 0x0 14. "MS,Master Select" "0: Slave mode,1: Master mode"
|
|
bitfld.long 0x0 12. "AREN,Automatic Reset Enable" "0: No automatic reset upon baud-rate error,1: Automatic reset upon baud-rate error"
|
|
newline
|
|
bitfld.long 0x0 9. "LB,Loop Back Control" "0: Normal Operation,1: Internal Loopback Mode (Rx to Tx)"
|
|
bitfld.long 0x0 8. "PO,Clock Polarity Control" "0: SCLK idle level is low,1: SCLK idle level is high"
|
|
newline
|
|
bitfld.long 0x0 7. "PH,Clock Phase Control" "0: Shift on leading SCLK edge,1: Shift on trailing SCLK edge"
|
|
bitfld.long 0x0 6. "HB,Heading Control" "0: Transmit/Receive LSB First.,1: Transmit/Receive MSB First."
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "BM,Data Width Selection - Number of bits per transfer"
|
|
group.long 0x8++0x7
|
|
line.long 0x0 "CSTIM,Master Mode Chip Select Timings Register"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HIGH,CS High Time"
|
|
hexmask.long.byte 0x0 8.--13. 1. "END,CS Hold Time"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "ST,CS Setup Time"
|
|
line.long 0x4 "IEN,Interrupt Enable Register"
|
|
bitfld.long 0x4 5. "BEIREN,Baud Rate Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 4. "PEIREN,Phase Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 3. "REIREN,Receive Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 2. "TEIREN,Transmit Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "RIREN,Receive Buffer Full Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 0. "TIREN,Transmit Buffer Empty Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "INSEL,Port Input Select Register"
|
|
bitfld.long 0x0 8.--9. "TXEVSEL,Master Mode TX Start Event Input Select" "0: STARTA input,1: STARTB input,2: STARTC input,3: STARTD input"
|
|
bitfld.long 0x0 6.--7. "SLCSSEL,Slave Mode Chip Select Input Select" "0: SLSA input,1: SLSB input,2: SLSC input,3: SLSD input"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "MTSRSEL,Slave Mode Data Input Select" "0: MTSRA input,1: MTSRB input,2: MTSRC input,3: MTSRD input"
|
|
bitfld.long 0x0 2.--3. "SLCLKSEL,Slave Mode Clock Input Select" "0: SCLKA input,1: SCLKB input,2: SCLKC input,3: SCLKD input"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "MRSTSEL,Master Mode Data Input Select" "0: MRSTA input,1: MRSTB input,2: MRSTC input,3: MRSTD input"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "IS,Interrupt Status Register"
|
|
bitfld.long 0x0 5. "BEIR,Baud Rate Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "PEIR,Phase Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "REIR,Receive Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "TEIR,Transmit Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "RIR,Receive Buffer Full Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "TIR,Transmit Buffer Empty Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x18++0x3
|
|
line.long 0x0 "ISC,Interrupt Status Clear Register"
|
|
bitfld.long 0x0 5. "BEIRCLR,Baud Rate Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "PEIRCLR,Phase Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "REIRCLR,Receive Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "TEIRCLR,Transmit Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "RIRCLR,Receive Buffer Full Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "TIRCLR,Transmit Buffer Empty Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
wgroup.long 0x14++0x3
|
|
line.long 0x0 "ISS,Interrupt Status Set Register"
|
|
bitfld.long 0x0 5. "BEIRSET,Baud Rate Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 4. "PEIRSET,Phase Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 3. "REIRSET,Receive Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 2. "TEIRSET,Transmit Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 1. "RIRSET,Receive Buffer Full Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 0. "TIRSET,Transmit Buffer Empty Interrupt Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
rgroup.long 0x28++0xB
|
|
line.long 0x0 "RB0,Receiver Buffer Register Bits [31:0]"
|
|
hexmask.long 0x0 0.--31. 1. "RB_VALUE_LOWER,Receive Data [31:0]"
|
|
line.long 0x4 "RB1,Receiver Buffer Register Bits [63:32]"
|
|
hexmask.long 0x4 0.--31. 1. "RB_VALUE_UPPER,Receive Data [63:32]"
|
|
line.long 0x8 "STAT,Status Register"
|
|
bitfld.long 0x8 6. "BSY,Busy Flag" "0: No Data Transfer Ongoing,1: Data Transfer Ongoing"
|
|
hexmask.long.byte 0x8 0.--5. 1. "BC,Bit Count Field"
|
|
group.long 0x20++0x7
|
|
line.long 0x0 "TB0,Transmitter Buffer Register Bits [31:0]"
|
|
hexmask.long 0x0 0.--31. 1. "TB_VALUE_LOWER,Transmit Data [31:0]"
|
|
line.long 0x4 "TB1,Transmitter Buffer Register Bits [63:32]"
|
|
hexmask.long 0x4 0.--31. 1. "TB_VALUE_UPPER,Transmit Data [63:32]"
|
|
tree.end
|
|
tree "SSC1"
|
|
base ad:0x48024000
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "BR,Baud Rate Timer Register"
|
|
hexmask.long.word 0x0 0.--15. 1. "BR_VALUE,Baud Rate Timer Value"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CON,Control Register"
|
|
bitfld.long 0x0 23.--24. "MSTXENSEL,Master Mode Transmit Start Trigger Select" "0: Write to TB0,1: Set MSTXSTART,2: Rising edge on selected input,?"
|
|
bitfld.long 0x0 22. "MSTXSTART,Master Mode Transmit Start Bit" "0: No Data Transmission,1: Software Start Event"
|
|
newline
|
|
hexmask.long.byte 0x0 18.--21. 1. "MSCSSEL,Master Chip Select Output Selection"
|
|
bitfld.long 0x0 17. "MSCSEN,Master Chip Select Enable" "0: No master chip select is used,1: The selected CSx is used as master chip select"
|
|
newline
|
|
bitfld.long 0x0 16. "SLCSEN,Slave Chip Select Enable" "0: No slave chip select is used,1: SLS input is used as slave chip select"
|
|
bitfld.long 0x0 15. "EN,Enable Bit" "0: SSC Module disabled,1: SSC Module enabled"
|
|
newline
|
|
bitfld.long 0x0 14. "MS,Master Select" "0: Slave mode,1: Master mode"
|
|
bitfld.long 0x0 12. "AREN,Automatic Reset Enable" "0: No automatic reset upon baud-rate error,1: Automatic reset upon baud-rate error"
|
|
newline
|
|
bitfld.long 0x0 9. "LB,Loop Back Control" "0: Normal Operation,1: Internal Loopback Mode (Rx to Tx)"
|
|
bitfld.long 0x0 8. "PO,Clock Polarity Control" "0: SCLK idle level is low,1: SCLK idle level is high"
|
|
newline
|
|
bitfld.long 0x0 7. "PH,Clock Phase Control" "0: Shift on leading SCLK edge,1: Shift on trailing SCLK edge"
|
|
bitfld.long 0x0 6. "HB,Heading Control" "0: Transmit/Receive LSB First.,1: Transmit/Receive MSB First."
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "BM,Data Width Selection - Number of bits per transfer"
|
|
group.long 0x8++0x7
|
|
line.long 0x0 "CSTIM,Master Mode Chip Select Timings Register"
|
|
hexmask.long.byte 0x0 16.--21. 1. "HIGH,CS High Time"
|
|
hexmask.long.byte 0x0 8.--13. 1. "END,CS Hold Time"
|
|
newline
|
|
hexmask.long.byte 0x0 0.--5. 1. "ST,CS Setup Time"
|
|
line.long 0x4 "IEN,Interrupt Enable Register"
|
|
bitfld.long 0x4 5. "BEIREN,Baud Rate Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 4. "PEIREN,Phase Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 3. "REIREN,Receive Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 2. "TEIREN,Transmit Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x4 1. "RIREN,Receive Buffer Full Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x4 0. "TIREN,Transmit Buffer Empty Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "INSEL,Port Input Select Register"
|
|
bitfld.long 0x0 8.--9. "TXEVSEL,Master Mode TX Start Event Input Select" "0: STARTA input,1: STARTB input,2: STARTC input,3: STARTD input"
|
|
bitfld.long 0x0 6.--7. "SLCSSEL,Slave Mode Chip Select Input Select" "0: SLSA input,1: SLSB input,2: SLSC input,3: SLSD input"
|
|
newline
|
|
bitfld.long 0x0 4.--5. "MTSRSEL,Slave Mode Data Input Select" "0: MTSRA input,1: MTSRB input,2: MTSRC input,3: MTSRD input"
|
|
bitfld.long 0x0 2.--3. "SLCLKSEL,Slave Mode Clock Input Select" "0: SCLKA input,1: SCLKB input,2: SCLKC input,3: SCLKD input"
|
|
newline
|
|
bitfld.long 0x0 0.--1. "MRSTSEL,Master Mode Data Input Select" "0: MRSTA input,1: MRSTB input,2: MRSTC input,3: MRSTD input"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "IS,Interrupt Status Register"
|
|
bitfld.long 0x0 5. "BEIR,Baud Rate Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 4. "PEIR,Phase Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 3. "REIR,Receive Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 2. "TEIR,Transmit Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "RIR,Receive Buffer Full Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "TIR,Transmit Buffer Empty Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x18++0x3
|
|
line.long 0x0 "ISC,Interrupt Status Clear Register"
|
|
bitfld.long 0x0 5. "BEIRCLR,Baud Rate Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 4. "PEIRCLR,Phase Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 3. "REIRCLR,Receive Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 2. "TEIRCLR,Transmit Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "RIRCLR,Receive Buffer Full Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "TIRCLR,Transmit Buffer Empty Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
wgroup.long 0x14++0x3
|
|
line.long 0x0 "ISS,Interrupt Status Set Register"
|
|
bitfld.long 0x0 5. "BEIRSET,Baud Rate Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 4. "PEIRSET,Phase Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 3. "REIRSET,Receive Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 2. "TEIRSET,Transmit Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 1. "RIRSET,Receive Buffer Full Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 0. "TIRSET,Transmit Buffer Empty Interrupt Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
rgroup.long 0x28++0xB
|
|
line.long 0x0 "RB0,Receiver Buffer Register Bits [31:0]"
|
|
hexmask.long 0x0 0.--31. 1. "RB_VALUE_LOWER,Receive Data [31:0]"
|
|
line.long 0x4 "RB1,Receiver Buffer Register Bits [63:32]"
|
|
hexmask.long 0x4 0.--31. 1. "RB_VALUE_UPPER,Receive Data [63:32]"
|
|
line.long 0x8 "STAT,Status Register"
|
|
bitfld.long 0x8 6. "BSY,Busy Flag" "0: No Data Transfer Ongoing,1: Data Transfer Ongoing"
|
|
hexmask.long.byte 0x8 0.--5. 1. "BC,Bit Count Field"
|
|
group.long 0x20++0x7
|
|
line.long 0x0 "TB0,Transmitter Buffer Register Bits [31:0]"
|
|
hexmask.long 0x0 0.--31. 1. "TB_VALUE_LOWER,Transmit Data [31:0]"
|
|
line.long 0x4 "TB1,Transmitter Buffer Register Bits [63:32]"
|
|
hexmask.long 0x4 0.--31. 1. "TB_VALUE_UPPER,Transmit Data [63:32]"
|
|
tree.end
|
|
tree.end
|
|
tree "TIMER"
|
|
base ad:0x0
|
|
tree "T20 (Timer20)"
|
|
base ad:0x48028000
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "CNT,Timer 2 Count Register"
|
|
hexmask.long.byte 0x0 8.--15. 1. "T2H,Timer 2 Value"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T2L,Timer 2 Value"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CON,Timer 2 Control Register"
|
|
bitfld.long 0x0 10.--11. "T2EXINSEL,Timer 2 capture input selection" "0: T2EXA input selected,1: T2EXB input selected,2: T2EXC input selected,3: T2EXD input selected"
|
|
bitfld.long 0x0 8.--9. "T2INSEL,Timer 2 count input selection" "0: T2A input selected,1: T2B input selected,2: T2C input selected,3: T2D input selected"
|
|
newline
|
|
rbitfld.long 0x0 7. "TF2,Timer 2 Overflow/Underflow Flag" "0,1"
|
|
rbitfld.long 0x0 6. "EXF2,Timer 2 External Flag" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "EXEN2,Timer 2 External Enable Control" "0: External events are disabled.,1: External events are enabled in.."
|
|
bitfld.long 0x0 2. "TR2,Timer 2 Start/Stop Control" "0: Timer 2.,1: Timer 2."
|
|
newline
|
|
bitfld.long 0x0 1. "C_T2,Timer or Counter Select" "0: function selected.,1: upon negative edge at pin T2."
|
|
bitfld.long 0x0 0. "CP_RL2,Capture/Reload Select" "0: upon overflow or upon negative/positive..,1: Timer 2 data register contents on the.."
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "CON1,Timer 2 Control Register 1"
|
|
bitfld.long 0x0 1. "TF2EN,Overflow/Underflow Interrupt Enable" "0: Overflow/underflow interrupt.,1: Overflow/underflow interrupt."
|
|
bitfld.long 0x0 0. "EXF2EN,External Interrupt Enable" "0: External interrupt.,1: External interrupt"
|
|
wgroup.long 0x18++0x3
|
|
line.long 0x0 "ICLR,Timer 2 Interrupt Clear Register"
|
|
bitfld.long 0x0 7. "TF2CLR,Overflow/Underflow Interrupt Clear Flag" "0: Overflow/underflow interrupt is not cleared.,1: Overflow/underflow interrupt"
|
|
bitfld.long 0x0 6. "EXF2CLR,External Interrupt Clear Flag" "0: External interrupt is not cleared.,1: External interrupt"
|
|
group.long 0x4++0x7
|
|
line.long 0x0 "MOD,Timer 2 Mode Register"
|
|
bitfld.long 0x0 7. "T2REGS,Edge Select for Timer 2 External Start" "0: The falling edge at Pin T2EX is selected.,1: The rising edge at Pin T2EX is selected."
|
|
bitfld.long 0x0 6. "T2RHEN,Timer 2 External Start Enable" "0: Timer 2 External Start is disabled.,1: Timer 2 External Start is enabled."
|
|
newline
|
|
bitfld.long 0x0 5. "EDGESEL,Edge Select in Capture Mode/Reload Mode/Baud-rate Generator Mode" "0: The falling edge at Pin T2EX is selected.,1: The rising edge at Pin T2EX is selected."
|
|
bitfld.long 0x0 4. "PREN,Prescaler Enable" "0: Prescaler is disabled and the 2 or 12 divider..,1: Prescaler is enabled (see T2PRE bit) and the 2.."
|
|
newline
|
|
bitfld.long 0x0 1.--3. "T2PRE,Timer 2 Prescaler Bit" "0: DIV1,1: DIV2,2: D,3: DIV8,4: DIV16,5: DIV32,6: DIV64,7: DIV128"
|
|
bitfld.long 0x0 0. "DCEN,Up/Down Counter Enable" "0: Up/Down Counter function is disabled,1: Up/Down Counter function is enabled and.."
|
|
line.long 0x4 "RC,Timer 2 Reload/Capture Register"
|
|
hexmask.long.byte 0x4 8.--15. 1. "RCH2,Reload/Capture Value"
|
|
hexmask.long.byte 0x4 0.--7. 1. "RCL2,Reload/Capture Value"
|
|
tree.end
|
|
tree "T21 (Timer21)"
|
|
base ad:0x4802C000
|
|
group.long 0x10++0x3
|
|
line.long 0x0 "CNT,Timer 2 Count Register"
|
|
hexmask.long.byte 0x0 8.--15. 1. "T2H,Timer 2 Value"
|
|
hexmask.long.byte 0x0 0.--7. 1. "T2L,Timer 2 Value"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "CON,Timer 2 Control Register"
|
|
bitfld.long 0x0 10.--11. "T2EXINSEL,Timer 2 capture input selection" "0: T2EXA input selected,1: T2EXB input selected,2: T2EXC input selected,3: T2EXD input selected"
|
|
bitfld.long 0x0 8.--9. "T2INSEL,Timer 2 count input selection" "0: T2A input selected,1: T2B input selected,2: T2C input selected,3: T2D input selected"
|
|
newline
|
|
rbitfld.long 0x0 7. "TF2,Timer 2 Overflow/Underflow Flag" "0,1"
|
|
rbitfld.long 0x0 6. "EXF2,Timer 2 External Flag" "0,1"
|
|
newline
|
|
bitfld.long 0x0 3. "EXEN2,Timer 2 External Enable Control" "0: External events are disabled.,1: External events are enabled in.."
|
|
bitfld.long 0x0 2. "TR2,Timer 2 Start/Stop Control" "0: Timer 2.,1: Timer 2."
|
|
newline
|
|
bitfld.long 0x0 1. "C_T2,Timer or Counter Select" "0: function selected.,1: upon negative edge at pin T2."
|
|
bitfld.long 0x0 0. "CP_RL2,Capture/Reload Select" "0: upon overflow or upon negative/positive..,1: Timer 2 data register contents on the.."
|
|
group.long 0x1C++0x3
|
|
line.long 0x0 "CON1,Timer 2 Control Register 1"
|
|
bitfld.long 0x0 1. "TF2EN,Overflow/Underflow Interrupt Enable" "0: Overflow/underflow interrupt.,1: Overflow/underflow interrupt."
|
|
bitfld.long 0x0 0. "EXF2EN,External Interrupt Enable" "0: External interrupt.,1: External interrupt"
|
|
wgroup.long 0x18++0x3
|
|
line.long 0x0 "ICLR,Timer 2 Interrupt Clear Register"
|
|
bitfld.long 0x0 7. "TF2CLR,Overflow/Underflow Interrupt Clear Flag" "0: Overflow/underflow interrupt is not cleared.,1: Overflow/underflow interrupt"
|
|
bitfld.long 0x0 6. "EXF2CLR,External Interrupt Clear Flag" "0: External interrupt is not cleared.,1: External interrupt"
|
|
group.long 0x4++0x7
|
|
line.long 0x0 "MOD,Timer 2 Mode Register"
|
|
bitfld.long 0x0 7. "T2REGS,Edge Select for Timer 2 External Start" "0: The falling edge at Pin T2EX is selected.,1: The rising edge at Pin T2EX is selected."
|
|
bitfld.long 0x0 6. "T2RHEN,Timer 2 External Start Enable" "0: Timer 2 External Start is disabled.,1: Timer 2 External Start is enabled."
|
|
newline
|
|
bitfld.long 0x0 5. "EDGESEL,Edge Select in Capture Mode/Reload Mode/Baud-rate Generator Mode" "0: The falling edge at Pin T2EX is selected.,1: The rising edge at Pin T2EX is selected."
|
|
bitfld.long 0x0 4. "PREN,Prescaler Enable" "0: Prescaler is disabled and the 2 or 12 divider..,1: Prescaler is enabled (see T2PRE bit) and the 2.."
|
|
newline
|
|
bitfld.long 0x0 1.--3. "T2PRE,Timer 2 Prescaler Bit" "0: DIV1,1: DIV2,2: D,3: DIV8,4: DIV16,5: DIV32,6: DIV64,7: DIV128"
|
|
bitfld.long 0x0 0. "DCEN,Up/Down Counter Enable" "0: Up/Down Counter function is disabled,1: Up/Down Counter function is enabled and.."
|
|
line.long 0x4 "RC,Timer 2 Reload/Capture Register"
|
|
hexmask.long.byte 0x4 8.--15. 1. "RCH2,Reload/Capture Value"
|
|
hexmask.long.byte 0x4 0.--7. 1. "RCL2,Reload/Capture Value"
|
|
tree.end
|
|
tree.end
|
|
tree "UART (Universal Asynchronous Receiver/Transmitter)"
|
|
base ad:0x0
|
|
tree "UART0"
|
|
base ad:0x48018000
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "BCON,Baud Rate Control Register"
|
|
hexmask.long.word 0x0 21.--31. 1. "BG_BR_VALUE,Baud Rate Reload Value"
|
|
hexmask.long.byte 0x0 16.--20. 1. "BG_FD_SEL,Fractional Divider Selection"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "BR_PRE,Prescaler Bit" "0: fdiv = uart_clk,1: fdiv = uart_clk/2,2: fdiv = uart_clk/4,3: fdiv = uart_clk/8,4: fdiv = uart_clk/16,5: fdiv = uart_clk/32,6: fdiv = uart_clk,7: fdiv = uart_clk"
|
|
bitfld.long 0x0 0. "BR_R,Baud Rate Generator Enable Bit" "0: Baud Rate Generator disabled,1: Baud Rate Generator enabled"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "IEN,Interrupt Enable Register"
|
|
bitfld.long 0x0 9. "EOFSYNEN,End of SYN Byte Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 8. "ERRSYNEN,SYN Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "RIEN,Receive Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 0. "TIEN,Transmit Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "INSEL,Port Input Select Register"
|
|
bitfld.long 0x0 2.--3. "TXEVSEL,TX Start Event Input Select" "0: TXEV inp0,1: TXEV inp1,2: TXEV inp2,3: TXEV inp3"
|
|
bitfld.long 0x0 0.--1. "RXDSEL,RXD Input Select" "0: RXD inp0,1: RXD inp1,2: RXD inp2,3: RXD inp3"
|
|
rgroup.long 0x18++0x3
|
|
line.long 0x0 "IS,Interrupt Status Register"
|
|
bitfld.long 0x0 9. "EOFSYN,End of SYN Byte Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 8. "ERRSYN,SYN Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "RI,Receive Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "TI,Transmit Buffer Empty Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x20++0x3
|
|
line.long 0x0 "ISC,Interrupt Status Clear Register"
|
|
bitfld.long 0x0 9. "EOFSYNCLR,End of SYN Byte Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 8. "ERRSYNCLR,SYN Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "RICLR,Receive Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "TICLR,Transmit Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
wgroup.long 0x1C++0x3
|
|
line.long 0x0 "ISS,Interrupt Status Set Register"
|
|
bitfld.long 0x0 9. "EOFSYNSET,End of SYN Byte Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 8. "ERRSYNSET,SYN Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 1. "RISET,Receive Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 0. "TISET,Transmit Interrupt Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "LINCON,LIN Control Register"
|
|
bitfld.long 0x0 1.--2. "BGSEL,Baud Rate Select for Detection" "0,1,2,3"
|
|
bitfld.long 0x0 0. "BREN,Baud Rate Detection Enable" "0: Break/Sync detection is disabled,1: Break/Sync detection is enabled"
|
|
rgroup.long 0x2C++0x3
|
|
line.long 0x0 "LINST,LIN Status Register"
|
|
bitfld.long 0x0 0. "BRK,Break Field Detection Flag" "0: Break Field is not detected,1: Break Field is detected"
|
|
wgroup.long 0x30++0x7
|
|
line.long 0x0 "LINSTC,LIN Status Clear Register"
|
|
bitfld.long 0x0 0. "BRKCLR,Break Field Flag Clear" "0: Break Field is not cleared,1: Break Field is cleared"
|
|
line.long 0x4 "LINSTS,LIN Status Set Register"
|
|
bitfld.long 0x4 0. "BRKSET,Break Field Flag Set" "0: Break Field is not set,1: Break Field is set"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "RXBUF,Serial RX Data Buffer"
|
|
bitfld.long 0x0 8. "RB8,Serial Port Receiver Bit 9" "0,1"
|
|
hexmask.long.byte 0x0 0.--7. 1. "RXDATA,Serial Interface RxBuffer Register"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "SCON,Serial Channel Control Register"
|
|
bitfld.long 0x0 8.--9. "TXENSEL,Transmit Start Trigger Select" "0: Write to TXBUF starts transmission,1: Write to TXSTART starts transmission,2: TXEV rising edge starts transmission,?"
|
|
bitfld.long 0x0 5. "TXINV,TX Data Inverter Enable" "0: Serial TXD is not inverted,1: Serial TXD is inverted"
|
|
newline
|
|
bitfld.long 0x0 4. "RMOD,Receiver Mode" "0: In Mode1-3 RXBUF is not updated if IS.RI is..,1: In Mode1-3 RXBUF is updated if IS.RI is still set"
|
|
bitfld.long 0x0 3. "REN,Enable Receiver of Serial Port" "0: Serial reception is disabled,1: Serial reception is enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "SM2,Enable Serial Port Multiprocessor Communication in Mode 2 and 3" "0,1"
|
|
bitfld.long 0x0 1. "SM1,Serial Port Operating Mode Selection" "0,1"
|
|
newline
|
|
bitfld.long 0x0 0. "SM0,Serial Port Operating Mode Selection" "0,1"
|
|
wgroup.long 0x8++0x3
|
|
line.long 0x0 "TSTART,Transmit Start Register"
|
|
bitfld.long 0x0 0. "TXSTART,Transmit Start Bit" "0: No Data Transmission,1: Start Data Transmission"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "TXBUF,Serial TX Data Buffer"
|
|
bitfld.long 0x0 8. "TB8,Serial Port Transmitter Bit 9" "0,1"
|
|
hexmask.long.byte 0x0 0.--7. 1. "TXDATA,Serial Interface TxBuffer Register"
|
|
tree.end
|
|
tree "UART1"
|
|
base ad:0x4801C000
|
|
group.long 0x24++0x3
|
|
line.long 0x0 "BCON,Baud Rate Control Register"
|
|
hexmask.long.word 0x0 21.--31. 1. "BG_BR_VALUE,Baud Rate Reload Value"
|
|
hexmask.long.byte 0x0 16.--20. 1. "BG_FD_SEL,Fractional Divider Selection"
|
|
newline
|
|
bitfld.long 0x0 4.--6. "BR_PRE,Prescaler Bit" "0: fdiv = uart_clk,1: fdiv = uart_clk/2,2: fdiv = uart_clk/4,3: fdiv = uart_clk/8,4: fdiv = uart_clk/16,5: fdiv = uart_clk/32,6: fdiv = uart_clk,7: fdiv = uart_clk"
|
|
bitfld.long 0x0 0. "BR_R,Baud Rate Generator Enable Bit" "0: Baud Rate Generator disabled,1: Baud Rate Generator enabled"
|
|
group.long 0x14++0x3
|
|
line.long 0x0 "IEN,Interrupt Enable Register"
|
|
bitfld.long 0x0 9. "EOFSYNEN,End of SYN Byte Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 8. "ERRSYNEN,SYN Error Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
newline
|
|
bitfld.long 0x0 1. "RIEN,Receive Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
bitfld.long 0x0 0. "TIEN,Transmit Interrupt Enable" "0: Interrupt disabled,1: Interrupt enabled"
|
|
group.long 0x0++0x3
|
|
line.long 0x0 "INSEL,Port Input Select Register"
|
|
bitfld.long 0x0 2.--3. "TXEVSEL,TX Start Event Input Select" "0: TXEV inp0,1: TXEV inp1,2: TXEV inp2,3: TXEV inp3"
|
|
bitfld.long 0x0 0.--1. "RXDSEL,RXD Input Select" "0: RXD inp0,1: RXD inp1,2: RXD inp2,3: RXD inp3"
|
|
rgroup.long 0x18++0x3
|
|
line.long 0x0 "IS,Interrupt Status Register"
|
|
bitfld.long 0x0 9. "EOFSYN,End of SYN Byte Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 8. "ERRSYN,SYN Error Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
newline
|
|
bitfld.long 0x0 1. "RI,Receive Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
bitfld.long 0x0 0. "TI,Transmit Buffer Empty Interrupt Flag" "0: Interrupt not occurred,1: Interrupt occurred"
|
|
wgroup.long 0x20++0x3
|
|
line.long 0x0 "ISC,Interrupt Status Clear Register"
|
|
bitfld.long 0x0 9. "EOFSYNCLR,End of SYN Byte Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 8. "ERRSYNCLR,SYN Error Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
newline
|
|
bitfld.long 0x0 1. "RICLR,Receive Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
bitfld.long 0x0 0. "TICLR,Transmit Interrupt Clear" "0: Interrupt not cleared,1: Interrupt cleared"
|
|
wgroup.long 0x1C++0x3
|
|
line.long 0x0 "ISS,Interrupt Status Set Register"
|
|
bitfld.long 0x0 9. "EOFSYNSET,End of SYN Byte Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 8. "ERRSYNSET,SYN Error Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
newline
|
|
bitfld.long 0x0 1. "RISET,Receive Interrupt Set" "0: Interrupt not set,1: Interrupt set"
|
|
bitfld.long 0x0 0. "TISET,Transmit Interrupt Set" "0: Interrupt not SET,1: Interrupt SET"
|
|
group.long 0x28++0x3
|
|
line.long 0x0 "LINCON,LIN Control Register"
|
|
bitfld.long 0x0 1.--2. "BGSEL,Baud Rate Select for Detection" "0,1,2,3"
|
|
bitfld.long 0x0 0. "BREN,Baud Rate Detection Enable" "0: Break/Sync detection is disabled,1: Break/Sync detection is enabled"
|
|
rgroup.long 0x2C++0x3
|
|
line.long 0x0 "LINST,LIN Status Register"
|
|
bitfld.long 0x0 0. "BRK,Break Field Detection Flag" "0: Break Field is not detected,1: Break Field is detected"
|
|
wgroup.long 0x30++0x7
|
|
line.long 0x0 "LINSTC,LIN Status Clear Register"
|
|
bitfld.long 0x0 0. "BRKCLR,Break Field Flag Clear" "0: Break Field is not cleared,1: Break Field is cleared"
|
|
line.long 0x4 "LINSTS,LIN Status Set Register"
|
|
bitfld.long 0x4 0. "BRKSET,Break Field Flag Set" "0: Break Field is not set,1: Break Field is set"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x0 "RXBUF,Serial RX Data Buffer"
|
|
bitfld.long 0x0 8. "RB8,Serial Port Receiver Bit 9" "0,1"
|
|
hexmask.long.byte 0x0 0.--7. 1. "RXDATA,Serial Interface RxBuffer Register"
|
|
group.long 0x4++0x3
|
|
line.long 0x0 "SCON,Serial Channel Control Register"
|
|
bitfld.long 0x0 8.--9. "TXENSEL,Transmit Start Trigger Select" "0: Write to TXBUF starts transmission,1: Write to TXSTART starts transmission,2: TXEV rising edge starts transmission,?"
|
|
bitfld.long 0x0 5. "TXINV,TX Data Inverter Enable" "0: Serial TXD is not inverted,1: Serial TXD is inverted"
|
|
newline
|
|
bitfld.long 0x0 4. "RMOD,Receiver Mode" "0: In Mode1-3 RXBUF is not updated if IS.RI is..,1: In Mode1-3 RXBUF is updated if IS.RI is still set"
|
|
bitfld.long 0x0 3. "REN,Enable Receiver of Serial Port" "0: Serial reception is disabled,1: Serial reception is enabled"
|
|
newline
|
|
bitfld.long 0x0 2. "SM2,Enable Serial Port Multiprocessor Communication in Mode 2 and 3" "0,1"
|
|
bitfld.long 0x0 1. "SM1,Serial Port Operating Mode Selection" "0,1"
|
|
newline
|
|
bitfld.long 0x0 0. "SM0,Serial Port Operating Mode Selection" "0,1"
|
|
wgroup.long 0x8++0x3
|
|
line.long 0x0 "TSTART,Transmit Start Register"
|
|
bitfld.long 0x0 0. "TXSTART,Transmit Start Bit" "0: No Data Transmission,1: Start Data Transmission"
|
|
group.long 0xC++0x3
|
|
line.long 0x0 "TXBUF,Serial TX Data Buffer"
|
|
bitfld.long 0x0 8. "TB8,Serial Port Transmitter Bit 9" "0,1"
|
|
hexmask.long.byte 0x0 0.--7. 1. "TXDATA,Serial Interface TxBuffer Register"
|
|
tree.end
|
|
tree.end
|
|
AUTOINDENT.OFF
|