130 lines
3.3 KiB
Plaintext
130 lines
3.3 KiB
Plaintext
; --------------------------------------------------------------------------------
|
|
; @Title: AT91SAM9XE Serial FLASH Programming Script
|
|
; @Description:
|
|
; Serial FLASH (ST, 25P64) is connected the SPI0 (Serial Peripheral Interface)
|
|
; or Serial Data FLASH (ATMEL, AT45DB642D) is connected the SPI0
|
|
; (Serial Peripheral Interface)
|
|
;
|
|
; Internal SRAM : 0x300000
|
|
; Serial FLASH Controller Addr: 0xFFFC8000
|
|
;
|
|
; @Author: jjeong
|
|
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
|
|
; @Chip: AT91SAM9XE*
|
|
; --------------------------------------------------------------------------------
|
|
; $Id: at91sam9xe-at45p1k.cmm 12049 2023-04-20 12:32:16Z bschroefel $
|
|
; $Rev: 12049 $
|
|
|
|
//SYStem Configuration
|
|
SYStem.RESet
|
|
SYStem.CPU AT91SAM9XE512
|
|
SYStem.JtagClock RTCK
|
|
SYStem.Option IMASKASM ON
|
|
SYStem.Option IMASKHLL ON
|
|
SYStem.Option RESBREAK OFF
|
|
SYStem.Option ENRESET ON
|
|
SYStem.Mode Up
|
|
|
|
Register.RESet
|
|
|
|
//CPU initialization
|
|
GOSUB cpu_Init
|
|
GOSUB spi_Init
|
|
|
|
Break.RESet
|
|
|
|
FLASHFILE.RESet
|
|
|
|
//The AT91SAM9XE doesn't have a common the SPI controller specially the CS is controlled by the SPI register 0xFFFC8000 not the specified GPIO ports.
|
|
//FLASFILE.CONFIG <Tx Reg> <Rx Reg> <CS> <port>
|
|
FLASHFILE.CONFIG 0xFFFC800C 0xFFFC8008 0xFFFC8000
|
|
|
|
//For the Serial Data Flash (ATMEL, AT45DB642D)
|
|
FLASHFILE.TARGET 0x300000++0x1FFF 0x302000++0x1FFF ~~/demo/arm/flash/byte/at45p1k_at91sam.bin
|
|
|
|
//Read FLASH Manufacture and Device ID
|
|
FLASHFILE.GETID
|
|
|
|
//Dump window for Serial FLASH
|
|
;FLASHFILE.DUMP 0x0
|
|
|
|
DIALOG.YESNO "Program flash memory?"
|
|
ENTRY &progflash
|
|
IF &progflash
|
|
(
|
|
//Erase Serial FLASH
|
|
FLASHFILE.Erase 0x0--0x7FFFFF
|
|
|
|
//Write Serial FLASH
|
|
FLASHFILE.LOAD.binary * 0x0
|
|
|
|
//Save Serial FLASH
|
|
;FLASHFILE.SAVE dump.bin 0x0--0x7FFFFF
|
|
)
|
|
|
|
ENDDO
|
|
|
|
cpu_Init:
|
|
//Setup PLL to 100MHz
|
|
Data.Set ASD:0xFFFFFC20 %Long 0x00004001
|
|
WAIT 10ms
|
|
Data.Set ASD:0xFFFFFC30 %Long 0x00000102
|
|
WAIT 10ms
|
|
Data.Set ASD:0xFFFFFC28 %Long 0x206dbf12
|
|
WAIT 10ms
|
|
|
|
WAIT 10ms
|
|
// It is necessary to write to memory after setting it up
|
|
Data.Set 0x20000000 %Long 0x1
|
|
|
|
// Reset ECC
|
|
PER.Set.simple ASD:0xFFFFE000 %Long 1
|
|
|
|
// Setup ITCM and DTCM
|
|
PER.Set.simple ASD:0xFFFFED14 %Long 0xB66
|
|
|
|
// Remap SRAM to 0x0
|
|
Data.Set SD:0xFFFFED00 %LE %Long 0x3
|
|
|
|
// Disable Watchdog
|
|
PER.Set.simple ASD:0xFFFFFD44 %Long 0x8000
|
|
|
|
RETURN
|
|
|
|
spi_Init:
|
|
// SPI FLash: configure PIOs in periph mode
|
|
PER.Set.simple ASD:0xFFFFF874 %Long 0x800 ;PIOC.11 define the NPCS0 Function
|
|
|
|
//Clock Enable for SPI
|
|
PER.Set.simple ASD:0xFFFFFC10 %Long 0x00003000
|
|
|
|
//AIC Interrupt Enable for SPI
|
|
PER.Set.simple ASD:0xFFFFF120 %Long 0x3000
|
|
|
|
PER.Set.simple ASD:0xFFFFF444 %Long 0x07
|
|
PER.Set.simple ASD:0xFFFFF464 %Long 0x01 ;pull-up enable
|
|
PER.Set.simple ASD:0xFFFFF460 %Long 0x06 ;pull-up disable
|
|
PER.Set.simple ASD:0xFFFFF470 %Long 0x7
|
|
PER.Set.simple ASD:0xFFFFF404 %Long 0x7
|
|
|
|
|
|
PER.Set.simple ASD:0xFFFFF844 %Long 0x0800
|
|
PER.Set.simple ASD:0xFFFFF860 %Long 0x0800 ;pull-up disable
|
|
PER.Set.simple ASD:0xFFFFF874 %Long 0x0800
|
|
PER.Set.simple ASD:0xFFFFF804 %Long 0x0800
|
|
|
|
|
|
PER.Set.simple ASD:0xFFFC8000 %Word 0x80
|
|
PER.Set.simple ASD:0xFFFC8000 %Word 0x80
|
|
|
|
PER.Set.simple ASD:0xFFFC8004 %Long 0x10011
|
|
|
|
;PER.S ASD:0xFFFC8034 %LONG 01196302
|
|
PER.Set.simple ASD:0xFFFC8034 %Long 0x01196309 ; this is important to recieved data buffer
|
|
;PER.S ASD:0xFFFC8034 %LONG FFFFFF09
|
|
|
|
//Disable PDC
|
|
PER.Set.simple ASD:0xFFFC8120 %Long 0x202
|
|
|
|
RETURN
|