36540 lines
2.4 MiB
36540 lines
2.4 MiB
; --------------------------------------------------------------------------------
|
|
; @Title: iMX35 On-Chip Peripherals
|
|
; @Props: Released
|
|
; @Author: ADI, BOB, FIL, MPO, PSS, TAT, ASK
|
|
; @Changelog: 2008-12-08
|
|
; 2011-10-27
|
|
; 2017-05-08 ASK
|
|
; @Manufacturer: NXP - NXP Semiconductors
|
|
; @Doc: IMX35_Reference_Manual.pdf Rev. 1.1 (2007-08)
|
|
; IMX35RM_20110907.pdf Rev. 3 (2010-11)
|
|
; @Core: ARM1136
|
|
; @Chip: IMX35
|
|
; @Copyright: (C) 1989-2017 Lauterbach GmbH, licensed for use with TRACE32(R) only
|
|
; --------------------------------------------------------------------------------
|
|
; $Id: permcimx35.per 7808 2017-05-08 13:16:57Z askoncej $
|
|
|
|
;Known problems:
|
|
;-GPIO Module/GPIO 3: Address does not match memmory map address. Appropriate adrress should be probobly 0x53fa0000
|
|
config 16. 8.
|
|
tree "ARM Core Registers"
|
|
width 8.
|
|
width 0x8
|
|
; --------------------------------------------------------------------------------
|
|
; Identification registers
|
|
; --------------------------------------------------------------------------------
|
|
tree "ID Registers"
|
|
rgroup c15:0x0--0x0
|
|
line.long 0x0 "MIDR,Main ID Register"
|
|
hexmask.long.byte 0x0 24.--31. 0x1 " IMPL ,Implementer code"
|
|
bitfld.long 0x0 20.--23. " VAR ,Variant" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 16.--19. " ARCH , Architecture" "Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,Pre-ARMv7,ARMv7"
|
|
textline " "
|
|
hexmask.long.word 0x0 4.--15. 0x1 " PART ,Primary Part Number"
|
|
bitfld.long 0x0 0.--3. " REV ,Revision Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
rgroup c15:0x100--0x100
|
|
line.long 0x0 "CTYPE,Cache Type Register"
|
|
bitfld.long 0x0 25.--28. " CTYPE ,Cache type" "0,1,2,3,4,5,6,7,8,9,a,b,c,d,e,f"
|
|
bitfld.long 0x0 24. " S ,Unified or Separate Instruction Cache" "Unified,Separate"
|
|
textline " "
|
|
bitfld.long 0x0 23. " DP ,Restriction on page allocation for bits [13:12] of the Virtual Address" "No restriction,Restriction"
|
|
bitfld.long 0x0 18.--20. " DSIZE ,Data Cache Size" "512,1k,2k,4k,8k,16k,32k,64k"
|
|
bitfld.long 0x0 15.--17. " DASS ,Data Cache Associativity" "Reserved,Reserved,4-way,?..."
|
|
bitfld.long 0x0 14. " DM ,Data multiplier bit" "0,1"
|
|
bitfld.long 0x0 12.--13. " DLENGTH ,Data Cache Line Length" "Reserved,Reserved,32 bytes,?..."
|
|
textline " "
|
|
bitfld.long 0x0 11. " IP ,Restriction on page allocation for bits [1:0] of the Virtual Address" "No restriction,Restriction"
|
|
bitfld.long 0x0 6.--8. " ISIZE ,Instruction Cache Size" "512,1k,2k,4k,8k,16k,32k,64k"
|
|
bitfld.long 0x0 3.--5. " IASS ,Instruction Cache Associativity" "Reserved,Reserved,4-way,?..."
|
|
bitfld.long 0x0 2. " IM ,Instruction multiplier bit" "0,1"
|
|
bitfld.long 0x0 0.--1. " ILENGTH ,Instruction Cache Line Length" "Reserved,Reserved,32 bytes,?..."
|
|
rgroup c15:0x200--0x200
|
|
line.long 0x0 "TCMS,TCM Status Register"
|
|
bitfld.long 0x0 16.--18. " DTCM ,Number of Data TCMs Implemented" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 0.--2. " ITCM ,Number of Instruction TCMs Implemented" "0,1,2,3,4,5,6,7"
|
|
rgroup c15:0x300--0x300
|
|
line.long 0x0 "TLBT,TLB Type Register"
|
|
hexmask.long.byte 0x0 16.--23. 0x1 " ITLBLOCK ,Specifies the Number of Instruction TLB Lockable Entries"
|
|
hexmask.long.byte 0x0 8.--15. 0x1 " DTLBLOCK ,Specifies the Number of Unified or Data TLB Lockable Entries"
|
|
bitfld.long 0x0 0. " U ,Unified or Separate Instruction TLBs" "Unified,Separate"
|
|
tree.end
|
|
tree "System Configuration and Control"
|
|
group c15:0x1--0x1
|
|
line.long 0x0 "CR,Control Register"
|
|
bitfld.long 0x0 29. " AFE ,Access Flag Enable" "Disable,Enable"
|
|
bitfld.long 0x0 28. " TRE ,TEX Remap Enable" "Disable,Enable"
|
|
bitfld.long 0x0 25. " EE ,Exception Endianess" "Little,Big"
|
|
bitfld.long 0x0 24. " VE ,Vector Enable" "Fixed,VIC"
|
|
textline " "
|
|
bitfld.long 0x0 23. " XP ,Extended pagetable configuration" "Subpages,ARMv6"
|
|
bitfld.long 0x0 22. " U ,Unaligned Data Access Operations" "Disable,Enable"
|
|
bitfld.long 0x0 21. " FI ,Fast Interrupts" "Disable,Enable"
|
|
bitfld.long 0x0 18. " IT ,Global Instruction TCM enable/disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 16. " DT ,Global Data TCM enable/disable" "No,Yes"
|
|
bitfld.long 0x0 15. " L4 ,Compatible to Software Version 4" "No,Yes"
|
|
bitfld.long 0x0 14. " RR ,Round Robin Replacement" "Random,Round robin"
|
|
textline " "
|
|
bitfld.long 0x0 13. " V ,Base Location of Exception Vectors" "0x00000000,0xFFFF0000"
|
|
bitfld.long 0x0 12. " I ,Level one Instruction Cache" "Disable,Enable"
|
|
bitfld.long 0x0 11. " Z ,Program flow prediction" "Disable,Enable"
|
|
bitfld.long 0x0 9. " R ,ROM Protection" "Disable,Enable"
|
|
textline " "
|
|
bitfld.long 0x0 8. " S ,System Protection" "Disable,Enable"
|
|
bitfld.long 0x0 7. " B ,Endianism" "Little,Big"
|
|
bitfld.long 0x0 2. " C ,Data Cache" "Disable,Enable"
|
|
bitfld.long 0x0 1. " A ,Alignment Fault Check" "Disable,Enable"
|
|
textline " "
|
|
bitfld.long 0x0 0. " M ,MMU" "Disable,Enable"
|
|
group c15:0x101--0x101
|
|
line.long 0x0 "ACR,Auxiliary Control Register"
|
|
bitfld.long 0x0 6. " CZ ,Restrict cache size" "Normal,Limited"
|
|
bitfld.long 0x0 5. " RV ,Disable Block Transfer Cache Operations" "Enable,Disable"
|
|
bitfld.long 0x0 4. " RA ,Disable Clean Entire Data Cache" "Enable,Disable"
|
|
bitfld.long 0x0 3. " TR ,MicroTLB Random Replacement" "Round robin,Random"
|
|
textline " "
|
|
bitfld.long 0x0 2. " SB ,Static Branch Prediction Enable" "Disable,Enable"
|
|
bitfld.long 0x0 1. " DB ,Dynamic Branch Prediction Enable" "Disable,Enable"
|
|
bitfld.long 0x0 0. " RS ,Return Stack Enable" "Disable,Enable"
|
|
group c15:0x201--0x201
|
|
line.long 0x0 "CACR,Coprocessor Access Control Register"
|
|
bitfld.long 0x0 26.--27. " CP13 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 24.--25. " CP12 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
textline " "
|
|
bitfld.long 0x0 22.--23. " CP11 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 20.--21. " CP10 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 18.--19. " CP9 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 16.--17. " CP8 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
textline " "
|
|
bitfld.long 0x0 14.--15. " CP7 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 12.--13. " CP6 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 10.--11. " CP5 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 8.--9. " CP4 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
textline " "
|
|
bitfld.long 0x0 6.--7. " CP3 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 4.--5. " CP2 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 2.--3. " CP1 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
bitfld.long 0x0 0.--1. " CP0 ,Coprocesor Access Control" "Denied,Priv,Res,Full"
|
|
tree.end
|
|
tree "Memory Management Unit"
|
|
width 0x8
|
|
group c15:0x1--0x1
|
|
line.long 0x0 "CR,Control Register"
|
|
bitfld.long 0x0 29. " AFE ,Access Flag Enable" "Disable,Enable"
|
|
bitfld.long 0x0 28. " TRE ,TEX Remap Enable" "Disable,Enable"
|
|
bitfld.long 0x0 25. " EE ,Exception Endianess" "Little,Big"
|
|
bitfld.long 0x0 24. " VE ,Vector Enable" "Fixed,VIC"
|
|
textline " "
|
|
bitfld.long 0x0 23. " XP ,Extended pagetable configuration" "Subpages,ARMv6"
|
|
bitfld.long 0x0 22. " U ,Unaligned Data Access Operations" "Disable,Enable"
|
|
bitfld.long 0x0 21. " FI ,Fast Interrupts" "Disable,Enable"
|
|
bitfld.long 0x0 18. " IT ,Global Instruction TCM enable/disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 16. " DT ,Global Data TCM enable/disable" "No,Yes"
|
|
bitfld.long 0x0 15. " L4 ,Compatible to Software Version 4" "No,Yes"
|
|
bitfld.long 0x0 14. " RR ,Round Robin Replacement" "Random,Round robin"
|
|
textline " "
|
|
bitfld.long 0x0 13. " V ,Base Location of Exception Vectors" "0x00000000,0xFFFF0000"
|
|
bitfld.long 0x0 12. " I ,Level one Instruction Cache" "Disable,Enable"
|
|
bitfld.long 0x0 11. " Z ,Program flow prediction" "Disable,Enable"
|
|
bitfld.long 0x0 9. " R ,ROM Protection" "Disable,Enable"
|
|
textline " "
|
|
bitfld.long 0x0 8. " S ,System Protection" "Disable,Enable"
|
|
bitfld.long 0x0 7. " B ,Endianism" "Little,Big"
|
|
bitfld.long 0x0 2. " C ,Data Cache" "Disable,Enable"
|
|
bitfld.long 0x0 1. " A ,Alignment Fault Check" "Disable,Enable"
|
|
textline " "
|
|
bitfld.long 0x0 0. " M ,MMU" "Disable,Enable"
|
|
group c15:0x0002++0x00
|
|
line.long 0x00 "TTBR0,Translation Table Base Register 0"
|
|
hexmask.long 0x00 14.--31. 0x4000 " TTB0 ,Translation Table Base Address"
|
|
bitfld.long 0x00 3.--4. " RGN ,Outer Cacheable Attributes for Page Table Walking" "Noncacheable,Copyback/allocated,Writethrough/not allocated,Copyback/not allocated"
|
|
textline " "
|
|
bitfld.long 0x00 1. " S ,Page Table Walk to Shared Memory" "Nonshared,Shared"
|
|
bitfld.long 0x00 0. " C ,Page Table Walk Inner Cacheable" "Noncacheable,Cacheable"
|
|
group c15:0x0102++0x00
|
|
line.long 0x00 "TTBR1,Translation Table Base Register 1"
|
|
hexmask.long 0x00 14.--31. 0x4000 " TTB1 ,Translation Table Base Address"
|
|
bitfld.long 0x00 3.--4. " RGN ,Outer Cacheable Attributes for Page Table Walking" "Noncacheable,Copyback/allocated,Writethrough/not allocated,Copyback/not allocated"
|
|
textline " "
|
|
bitfld.long 0x00 1. " S ,Page Table Walk to Shared Memory" "Nonshared,Shared"
|
|
bitfld.long 0x00 0. " C ,Page Table Walk Inner Cacheable" "Noncacheable,Cacheable"
|
|
group c15:0x0202++0x00
|
|
line.long 0x00 "TTBCR,Translation Table Base Control Register"
|
|
bitfld.long 0x0 0.--2. " N ,Translation Table Base Register 0 page table boundary size" "16KB,8KB,4KB,2KB,1KB,512-byte,256-byte,128-byte"
|
|
textline " "
|
|
group c15:0x3--0x3
|
|
line.long 0x0 "DACR,Domain Access Control Register"
|
|
bitfld.long 0x0 30.--31. " D15 ,Domain Access 15" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 28.--29. " D14 ,Domain Access 14" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 26.--27. " D13 ,Domain Access 13" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 24.--25. " D12 ,Domain Access 12" "Denied,Client,Reserved,Manager"
|
|
textline " "
|
|
bitfld.long 0x0 22.--23. " D11 ,Domain Access 11" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 20.--21. " D10 ,Domain Access 10" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 18.--19. " D9 ,Domain Access 9" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 16.--17. " D8 ,Domain Access 8" "Denied,Client,Reserved,Manager"
|
|
textline " "
|
|
bitfld.long 0x0 14.--15. " D7 ,Domain Access 7" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 12.--13. " D6 ,Domain Access 6" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 10.--11. " D5 ,Domain Access 5" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 8.--9. " D4 ,Domain Access 4" "Denied,Client,Reserved,Manager"
|
|
textline " "
|
|
bitfld.long 0x0 6.--7. " D3 ,Domain Access 3" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 4.--5. " D2 ,Domain Access 2" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 2.--3. " D1 ,Domain Access 1" "Denied,Client,Reserved,Manager"
|
|
bitfld.long 0x0 0.--1. " D0 ,Domain Access 0" "Denied,Client,Reserved,Manager"
|
|
textline " "
|
|
rgroup c15:0x5--0x5
|
|
line.long 0x0 "DFSR,Data Fault Status Register"
|
|
bitfld.long 0x0 11. " RW ,Indicates what Type of Access Caused the Abort" "Read,Write"
|
|
bitfld.long 0x0 0x4--0x7 " DOMAIN ,Domain" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 0x0--0x3 10. " STATUS ,Status" "Reserved,Alignment,Debug event,Access section flag,Cache maintenance,Translation section,Access page flag,Translation page,Precise external abort,Domain section,Reserved,Domain page,ext_abort_on_trans_l1,Permission section,ext_abort_on_trans_l2,Permission page,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Imprecise external abort,?..."
|
|
group c15:0x6--0x6
|
|
line.long 0x0 "DFAR,Data Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " MVA ,Modified Virtual Address of Fault Address"
|
|
rgroup c15:0x105--0x105
|
|
line.long 0x0 "IFSR,Instruction Fault Status Register"
|
|
bitfld.long 0x0 0x0--0x3 " STATUS ,Type of fault generated" "Reserved,Alignment,Debug event,Access section flag,Reserved,Translation section,Access page flag,Translation page,Precise external abort,Domain section,Reserved,Domain page,ext_abort_on_trans_l1,Permission section,ext_abort_on_trans_l2,Permission page"
|
|
group c15:0x106--0x106
|
|
line.long 0x0 "IFAR,Instruction Fault Address Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " MVA ,Modified Virtual Address of Fault Address"
|
|
textline ""
|
|
wgroup c15:0x058--0x058
|
|
line.long 0x0 "TLBOR,TLB Operations Register"
|
|
hexmask.long 0x0 12.--31. 0x1000 " MVA ,Modified Virtual Address"
|
|
hexmask.long.byte 0x0 0.--7. 1. " ASID ,ASID"
|
|
group c15:0xa--0xa
|
|
line.long 0x0 "TLBLR,TLB Lockdown Register"
|
|
bitfld.long 0x0 26.--28. " VICTIM ,Entry in the lockdown region" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x0 0. " P ,Lockdown by Victim or Set Associative Region of TLB" "Associative,Lockdown"
|
|
textline ""
|
|
group c15:0x02f--0x02f
|
|
line.long 0x0 "DTMRR,Data Memory Remap Register"
|
|
bitfld.long 0x0 23.--24. " OWB ,Outer Write-Back, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 21.--22. " OWT ,Outer Write-Trough, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 19.--20. " OWBWA ,Outer Write-Back, Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 17.--18. " ONC ,Outer Noncachable" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 16. " SH ,Shared Bit" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 15. " NSH ,Not Shared Bit" "No,Yes"
|
|
bitfld.long 0x0 12.--14. " IWB ,Inner Write-back" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 9.--11. " IWT ,Inner Write-Through" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 6.--8. " Dev , Device" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 3.--5. " SO ,Strongly Ordered" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 0.--2. " INC ,Inner Noncachable" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
group c15:0x12f--0x12f
|
|
line.long 0x0 "IMRR,Instruction Memory Remap Register"
|
|
bitfld.long 0x0 23.--24. " OWB ,Outer Write-Back, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 21.--22. " OWT ,Outer Write-Trough, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 19.--20. " OWBWA ,Outer Write-Back, Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 17.--18. " ONC ,Outer Noncachable" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 16. " SH ,Shared Bit" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 15. " NSH ,Not Shared Bit" "No,Yes"
|
|
bitfld.long 0x0 12.--14. " IWB ,Inner Write-back" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 9.--11. " IWT ,Inner Write-Through" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 6.--8. " Dev , Device" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 3.--5. " SO ,Strongly Ordered" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 0.--2. " INC ,Inner Noncachable" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
group c15:0x42f--0x42f
|
|
line.long 0x0 "PPMRR,Peripheral Port Memory Remap Register"
|
|
hexmask.long 0x00 12.--31. 0x1000 " BA ,Base Address"
|
|
bitfld.long 0x00 0.--4. " Size ,Ssize of the memory region that is to be remapped to be used by the peripheral port" "0KB,Reserved,Reserved,4KB,8KB,16KB,32KB,64KB,128KB,256KB,512KB,b01011,2MB,4MB,8MB,16MB,32MB,64MB,128MB,256MB,512MB,1GB,2GB,?..."
|
|
textline ""
|
|
group c15:0xd--0xd
|
|
line.long 0x0 "FCSEPID,FCSE PID Register"
|
|
hexmask.long.byte 0x0 25.--31. 0x1 " FCSEPID ,Specific process for fast context switch"
|
|
group c15:0x10d--0x10d
|
|
line.long 0x0 "CIDR,Context ID Register"
|
|
hexmask.long 0x0 8.--31. 0x1 " PROCID ,Process ID"
|
|
hexmask.long.byte 0x0 0.--7. 0x1 " ASID ,The ASID Value"
|
|
group c15:0x20d--0x20d
|
|
line.long 0x00 "URWTPID,User Read/Write Thread and Process ID Register"
|
|
group c15:0x30d--0x30d
|
|
line.long 0x00 "UROTPID,User Read Only Thread and Process ID Register"
|
|
group c15:0x40d--0x40d
|
|
line.long 0x00 "POTPID,Privileged Only Thread and Process ID Register"
|
|
tree.end
|
|
tree "Cache Configuration and Control"
|
|
group c15:0x009--0x009
|
|
line.long 0x0 "DCLR,Data Cache Lockdown Register"
|
|
bitfld.long 0x0 3. " L3 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 2. " L2 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 1. " L1 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 0. " L0 , Cache Lockdown" "Free,Locked"
|
|
group c15:0x109--0x109
|
|
line.long 0x0 "ICLR,Instruction Cache Lockdown Register"
|
|
bitfld.long 0x0 3. " L3 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 2. " L2 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 1. " L1 , Cache Lockdown" "Free,Locked"
|
|
bitfld.long 0x0 0. " L0 , Cache Lockdown" "Free,Locked"
|
|
group c15:0x107--0x107
|
|
line.long 0x0 "COR,Cache Operations Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " COV ,Cache Operations Value"
|
|
tree.end
|
|
tree "TCM Configuration and Control"
|
|
group c15:0x019--0x019
|
|
line.long 0x0 "DTCMR,Data TCM Region Register"
|
|
hexmask.long 0x0 12.--31. 0x1000 " BA ,Base Address (physical address)"
|
|
bitfld.long 0x0 2.--6. " S ,Indicates the size of the TCM" "0 KB,Reserved,Reserved,4 KB,8 KB,16 KB,32 KB,64 KB,?..."
|
|
bitfld.long 0x0 1. " SC ,Is TCM Enabled as SmartCache" "No,Yes"
|
|
bitfld.long 0x0 0. " En ,Indicates if TCM is Enabled" "Dis,Ena"
|
|
group c15:0x119--0x119
|
|
line.long 0x0 "ITCMR,Instruction TCM Region Register"
|
|
hexmask.long 0x0 12.--31. 0x1000 " BA ,Base Address (physical address)"
|
|
bitfld.long 0x0 2.--6. " S ,Indicates the Size of the TCM" "0 KB,Reserved,Reserved,4 KB,8 KB,16 KB,32 KB,64 KB,?..."
|
|
bitfld.long 0x0 1. " SC ,Is TCM Enabled as SmartCache" "No,Yes"
|
|
bitfld.long 0x0 0. " En ,Indicates if TCM is Enabled" "Dis,Ena"
|
|
tree.end
|
|
tree "DMA Control"
|
|
rgroup c15:0x10b--0x10b
|
|
line.long 0x0 "DMAISQR,DMA Identification and Status Queued Register"
|
|
bitfld.long 0x0 1. " CQ1 , DMA Channel 1 Queued" "No,Yes"
|
|
bitfld.long 0x0 0. " CQ0 , DMA Channel 0 Queued" "No,Yes"
|
|
rgroup c15:0x20b--0x20b
|
|
line.long 0x0 "DMAISRR,DMA Identification and Status Running Register"
|
|
bitfld.long 0x0 1. " CR1 , DMA Channel 1 Running" "No,Yes"
|
|
bitfld.long 0x0 0. " CR0 , DMA Channel 0 Running" "No,Yes"
|
|
rgroup c15:0x30b--0x30b
|
|
line.long 0x0 "DMAISIR,DMA Identification and Status Interrupting Register"
|
|
bitfld.long 0x0 1. " CR1 , DMA Channel 1 Interrupting" "No,Yes"
|
|
bitfld.long 0x0 0. " CR0 , DMA Channel 0 Interrupting" "No,Yes"
|
|
group c15:0x23b--0x23b
|
|
line.long 0x0 "DMAECR,DMA Enable Clear Register"
|
|
bitfld.long 0x0 1. " CE1 , DMA Channel 1 Enable Clear" "No,Yes"
|
|
bitfld.long 0x0 0. " CE0 , DMA Channel 0 Enable Clear" "No,Yes"
|
|
group c15:0x22f--0x22f
|
|
line.long 0x0 "DMRR,DMA Memory Remap Register"
|
|
bitfld.long 0x0 23.--24. " OWB ,Outer Write-Back, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 21.--22. " OWT ,Outer Write-Trough, No Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 19.--20. " OWBWA ,Outer Write-Back, Write on Allocate" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 17.--18. " ONC ,Outer Noncachable" "NC,WBWA,WTNWA,WBNWA"
|
|
bitfld.long 0x0 16. " SH ,Shared Bit" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 15. " NSH ,Not Shared Bit" "No,Yes"
|
|
bitfld.long 0x0 12.--14. " IWB ,Inner Write-back" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 9.--11. " IWT ,Inner Write-Through" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 6.--8. " Dev , Device" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 3.--5. " SO ,Strongly Ordered" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
bitfld.long 0x0 0.--2. " INC ,Inner Noncachable" "NC,SO,Res,Dev,Res,Res,WT,WB"
|
|
group c15:0x02b--0x02b
|
|
line.long 0x0 "DMACNR,DMA Channel Number Register"
|
|
bitfld.long 0x0 0. " CN ,DMA Channel Number" "0,1"
|
|
rgroup c15:0x8b--0x8b
|
|
line.long 0x0 "DMACSR, DMA Channel Status Register"
|
|
bitfld.long 0x0 12. " BP ,DMA Parameter Bit" "Acc,Ina"
|
|
bitfld.long 0x0 7.--11. " ES ,The External Address Error Status bits" "NoErr,NoErr,NoErr,NoErr,NoErr,NoErr,NoErr,NoErr,Res,UDE,Res,Res,Res,Res,Res,Res,Res,Res,Res,AFS,Res,TFS,AFP,TFP,Res,DFS,ExtAb,DFP,ExtAbF,PFS,ExtAbS,PFP"
|
|
bitfld.long 0x0 2.--6. " IS ,The Ixternal Address Error Status bits" "Res,Res,Res,Res,Res,Res,Res,Res,TCM out of range,Res,Res,Res,Res,Res,Res,Res,Res,Res,Res,AFS,Res,TFS,AFP,TFP,Res,DFS,Res,DFP,ExtAbF,PFS,ExtAbS,PFP"
|
|
bitfld.long 0x0 0.--1. " Status ,The Status Bits" "Idle,Queued,Running,CompErr"
|
|
group c15:0xfb--0xfb
|
|
line.long 0x0 "DMACIDR,DMA Context ID Register"
|
|
hexmask.long 0x0 8.--31. 0x1 " PROCID ,Process ID value"
|
|
hexmask.long.byte 0x0 0.--7. 0x1 " ASID ,ASID of the current process and identifies the current ASID"
|
|
group c15:0x4b--0x4b
|
|
line.long 0x0 "DMACR, DMA Control Register"
|
|
bitfld.long 0x0 31. " TR ,Target TCM" "Data,Instr"
|
|
bitfld.long 0x0 30. " DT ,Direction of Transfer" "FrLvl,ToLvl"
|
|
bitfld.long 0x0 29. " IC ,Interrupt on Completion" "No,Yes"
|
|
bitfld.long 0x0 28. " IE ,Interrupt on Error" "No,Yes"
|
|
bitfld.long 0x0 27. " FT ,Full Transfer" "TCM,All"
|
|
textline " "
|
|
bitfld.long 0x0 26. " UM ,User Mode" "Priv,User"
|
|
hexmask.long.word 0x0 8.--19. 0x1 " ST ,Stride in Bytes"
|
|
bitfld.long 0x0 0.--1. " TS ,Transaction Size" "Byte,Halfword,Word,Doubleword"
|
|
group c15:0x03b--0x03b
|
|
line.long 0x0 "DMAESR,DMA Enable Stop Register"
|
|
bitfld.long 0x0 1. " CE1 , DMA Channel 1 Enable Stop" "No,Yes"
|
|
bitfld.long 0x0 0. " CE0 , DMA Channel 0 Enable Stop" "No,Yes"
|
|
group c15:0x13b--0x13b
|
|
line.long 0x0 "DMAESTR,DMA Enable Start Register"
|
|
bitfld.long 0x0 1. " CE1 , DMA Channel 1 Enable Start" "No,Yes"
|
|
bitfld.long 0x0 0. " CE0 , DMA Channel 0 Enable Start" "No,Yes"
|
|
group c15:0x6b--0x6b
|
|
line.long 0x0 "DMAESAR,DMA External Start Address Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " ADR ,DMA External Start Address"
|
|
rgroup c15:0xb--0xb
|
|
line.long 0x0 "DMAISPR,DMA Identification and Status Present Register"
|
|
bitfld.long 0x0 1. " CP1 , DMA Channel 1 Present" "No,Yes"
|
|
bitfld.long 0x0 0. " CP0 , DMA Channel 0 Present" "No,Yes"
|
|
group c15:0x7b--0x7b
|
|
line.long 0x0 "DMAIEAR,DMA Internal End Address Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " ADR ,DMA Internal End Address"
|
|
group c15:0x5b--0x5b
|
|
line.long 0x0 "DMAISAR,DMA Internal Start Address Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " ADR ,DMA Internal Start Address"
|
|
group c15:0x01b--0x01b
|
|
line.long 0x0 "DMAUAR,DMA User Accessibility Register"
|
|
bitfld.long 0x0 1. " CU1 , DMA Channel 1 User Accessible" "No,Yes"
|
|
bitfld.long 0x0 0. " CU0 , DMA Channel 0 User Accessible" "No,Yes"
|
|
tree.end
|
|
tree "System Performance Monitoring"
|
|
group c15:0xcf--0xcf
|
|
line.long 0x0 "PMNC,Performance Monitor Control Register"
|
|
hexmask.long.byte 0x0 20.--27. 0x1 " EvtCount0 ,Identifies the Source of Events for Count Register 0"
|
|
hexmask.long.byte 0x0 12.--19. 0x1 " EvtCount1 ,Identifies the Source of Events for Count Register 1"
|
|
bitfld.long 0x0 11. " X ,Enable Export of the Events to the Event Bus" "Dis,Ena"
|
|
textline " "
|
|
bitfld.long 0x0 10. " CCR ,Cycle Count Register overflow flag" "Not occurred,Occurred"
|
|
bitfld.long 0x0 9. " CR1 ,Count Register 1 overflow flag" "Not occurred,Occurred"
|
|
bitfld.long 0x0 8. " CR0 ,Count Register 0 overflow flag" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x0 6. " ECC ,Enable Cycle Counter interrupt" "Dis,Ena"
|
|
bitfld.long 0x0 5. " EC1 ,Enable Counter Register 1 interrupt" "Dis,Ena"
|
|
bitfld.long 0x0 4. " EC0 ,Enable Counter Register 0 interrupt" "Dis,Ena"
|
|
textline " "
|
|
bitfld.long 0x0 3. " D ,Cycle Count Divider" "Every,64th"
|
|
bitfld.long 0x0 2. " C ,Cycle Counter Register Reset on Write" "Noact,Reset"
|
|
bitfld.long 0x0 1. " P ,Count Register Reset on Write" "Noact,Reset"
|
|
bitfld.long 0x0 0. " E ,Enable All Three Counters" "Dis,Ena"
|
|
group c15:0x2cf--0x2cf
|
|
line.long 0x0 "CR0,Count Register 0"
|
|
hexmask.long 0x0 0.--31. 0x1 " CR0 ,Counter Nr 0"
|
|
group c15:0x3cf--0x3cf
|
|
line.long 0x0 "CR1,Count Register 1"
|
|
hexmask.long 0x0 0.--31. 0x1 " CR1 ,Counter Nr 1"
|
|
group c15:0x1cf--0x1cf
|
|
line.long 0x0 "CCR,Cycle Counter Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " CCR ,Cycle Counter"
|
|
tree.end
|
|
tree "Debug Access to Caches and TLBs"
|
|
group c15:0x700f--0x700f
|
|
line.long 0x0 "CDCR,Cache Debug Control Register"
|
|
bitfld.long 0x0 2. " WT , Write-Through enable flag" "Dis,Ena"
|
|
bitfld.long 0x0 1. " IL , Instruction cache Linefill disable flag" "Ena,Dis"
|
|
bitfld.long 0x0 0. " DL , Data cache Linefill disable flag" "Ena,Dis"
|
|
wgroup c15:0x302f--0x302f
|
|
line.long 0x0 "DTRRO,Data Tag RAM Read Operation Register"
|
|
hexmask.long 0x0 5.--31. 0x1 " SETWAY ,Set/Way"
|
|
group c15:0x30cf--0x30cf
|
|
line.long 0x0 "DCMVR,Data Cache Master Valid Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " DCMV ,Data Cache Master Valid"
|
|
rgroup c15:0x310f--0x310f
|
|
line.long 0x0 "DBCR,Instruction Debug Cache Register"
|
|
hexmask.long 0x0 10.--31. 0x1 " TAG ,Tag Address"
|
|
bitfld.long 0x0 1.--2. " Dirty ,Dirty Bits" "00,01,10,11"
|
|
bitfld.long 0x0 0. " Valid ,Valid Bit" "No,Yes"
|
|
rgroup c15:0x300f--0x300f
|
|
line.long 0x0 "DBCR,Data Debug Cache Register"
|
|
hexmask.long 0x0 10.--31. 0x1 " TAG ,Tag Address"
|
|
bitfld.long 0x0 1.--2. " Dirty ,Dirty Bits" "00,01,10,11"
|
|
bitfld.long 0x0 0. " Valid ,Valid Bit" "No,Yes"
|
|
group c15:0x308f--0x308f
|
|
line.long 0x0 "ICMVR,Instruction Cache Master Valid Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " ICMV ,Instruction Cache Master Valid"
|
|
group c15:0x30ef--0x30ef
|
|
line.long 0x0 "DSCMVR,Data SmartCache Master Valid Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " DSCMV ,Data SmartCache Master Valid"
|
|
group c15:0x30af--0x30af
|
|
line.long 0x0 "ISCMVR,Instruction SmartCache Master Valid Register"
|
|
hexmask.long 0x0 0.--31. 0x1 " ISCMV ,Instruction SmartCache Master Valid"
|
|
rgroup c15:0x507f--0x507f
|
|
line.long 0x0 "DMTLBAR,Data MicroTLB Attribute Register"
|
|
bitfld.long 0x0 25. " SPV ,Subpage Valid" "No,Yes"
|
|
bitfld.long 0x0 5.--8. " Domain ,Domain number of the TLB entry" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x0 1.--3. " RGN ,Region Type" "Noncacheable,Strongly ordered,Reserved,Device,Reserved,Reserved,Inner WT,Inner WB"
|
|
bitfld.long 0x0 0. " S ,Shared Attribute" "0,1"
|
|
group c15:0x504f--0x504f
|
|
line.long 0x0 "DMTLBI,Data MicroTLB Index Register"
|
|
bitfld.long 0x0 0.--3. " IDX ,Micro TLB Index" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
rgroup c15:0x506f--0x506f
|
|
line.long 0x0 "DMTLBPA,Data MicroTLB PA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " PA ,Physical Address"
|
|
bitfld.long 0x0 6.--9. " SZ ,Region Size" "1MB section,Res,Res,Res,Res,Res,Res,Res,64KB page,Res,Res,Res,16KB subpage,Res,4KB page,1KB subpage"
|
|
bitfld.long 0x0 4.--5. " XRGN ,Extended Region Type" "NC,WBWA,WTNWA,WBNWA"
|
|
textline " "
|
|
bitfld.long 0x0 1.--3. " AP ,Access Permission" "No access,Supervisor only,No user write,Full access,Domain fault encoded,Supervisor read only,Supervisor/User read only,?..."
|
|
bitfld.long 0x0 0. " V ,Valid Bit" "No,Yes"
|
|
rgroup c15:0x505f--0x505f
|
|
line.long 0x0 "DMTLBVA,Data MicroTLB VA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " VA ,Virtual Address"
|
|
hexmask.long.word 0x0 0.--9. 0x1 " PROCESS ,Memory space identifier"
|
|
wgroup c15:0x314f--0x314f
|
|
line.long 0x0 "ICDRRO,Instruction Cache Data RAM Read Operations Register"
|
|
hexmask.long 0x0 5.--31. 0x1 " SETWAY ,Set/Way"
|
|
bitfld.long 0x0 2.--4. " WIL ,Word in Line" "0,1,2,3,4,5,6,7"
|
|
rgroup c15:0x517f--0x517f
|
|
line.long 0x0 "IMTLBAR,Instruction MicroTLB Attribute Register"
|
|
bitfld.long 0x0 25. " SPV ,Subpage Valid" "No,Yes"
|
|
bitfld.long 0x0 5.--8. " Domain ,Domain number of the TLB entry" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 4. " XN ,Execute Never Attribute" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--3. " RGN ,Region Type" "Noncacheable,Strongly ordered,Reserved,Device,Reserved,Reserved,Inner WT,Inner WB"
|
|
bitfld.long 0x0 0. " S ,Shared Attribute" "0,1"
|
|
group c15:0x514f--0x514f
|
|
line.long 0x0 "IMTLBI,Instruction MicroTLB Index Register"
|
|
bitfld.long 0x0 0.--3. " IDX ,Micro TLB Index" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
rgroup c15:0x516f--0x516f
|
|
line.long 0x0 "IMTLBPA,Instruction MicroTLB PA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " PA ,Physical Address"
|
|
bitfld.long 0x0 6.--9. " SZ ,Region Size" "1MB section,Res,Res,Res,Res,Res,Res,Res,64KB page,Res,Res,Res,16KB subpage,Res,4KB page,1KB subpage"
|
|
bitfld.long 0x0 4.--5. " XRGN ,Extended Region Type" "NC,WBAW,WTNAW,WB"
|
|
textline " "
|
|
bitfld.long 0x0 1.--3. " AP ,Access Permission" "No access,Supervisor only,No user write,Full access,Domain fault encoded,Supervisor read only,Supervisor/User read only,?..."
|
|
bitfld.long 0x0 0. " V ,Valid Bit" "No,Yes"
|
|
rgroup c15:0x515f--0x515f
|
|
line.long 0x0 "IMTLBVA,Instruction MicroTLB VA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " VA ,Virtual Address"
|
|
hexmask.long.word 0x0 0.--9. 0x1 " PROCESS ,Memory Space Identifier"
|
|
wgroup c15:0x312f--0x312f
|
|
line.long 0x0 "ITRRO,Instruction Tag RAM Read Operation Register"
|
|
hexmask.long 0x0 5.--31. 0x1 " SETWAY ,Set/Way"
|
|
group c15:0x527f--0x527f
|
|
line.long 0x0 "MTLBAR,Main TLB Attribute Register"
|
|
bitfld.long 0x0 30.--31. " AP3 ,Subpage Access Permissions" "All fault/Supervisor RO/Supervisor|User RO/UNP,Supervisor,Supervisor full,Full"
|
|
textline " "
|
|
bitfld.long 0x0 28.--29. " AP2 ,Subpage Access Permissions" "All fault/Supervisor RO/Supervisor|User RO/UNP,Supervisor,Supervisor full,Full"
|
|
textline " "
|
|
bitfld.long 0x0 26.--27. " AP1 ,Subpage Access Permissions" "All fault/Supervisor RO/Supervisor|User RO/UNP,Supervisor,Supervisor full,Full"
|
|
textline " "
|
|
bitfld.long 0x0 25. " SPV ,Subpage Valid" "No,Yes"
|
|
bitfld.long 0x0 5.--8. " Domain ,Domain number of the TLB entry" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 4. " XN ,Execute Never Attribute" "No,Yes"
|
|
bitfld.long 0x0 1.--3. " RGN ,Region Type" "Noncacheable,Strongly ordered,Reserved,Device,Reserved,Reserved,Inner WT,Inner WB"
|
|
bitfld.long 0x0 0. " S ,Shared Attribute" "0,1"
|
|
wgroup c15:0x524f--0x524f
|
|
line.long 0x0 "RMTLBER,Read Main TLB Entry Register"
|
|
bitfld.long 0x0 31. " L ,Lockable Region" "Set,Lock"
|
|
bitfld.long 0x0 0.--5. " IDX[0:5] ,Entry in the main TLB to access" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
wgroup c15:0x544f--0x544f
|
|
line.long 0x0 "WMTLBER,Write Main TLB Entry Register"
|
|
bitfld.long 0x0 31. " L ,Lockable Region" "Set,Lock"
|
|
bitfld.long 0x0 0.--5. " IDX[0:5] ,Entry in the main TLB to access" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
group c15:0x526f--0x526f
|
|
line.long 0x0 "MTLBPA,Main TLB PA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " PA ,Physical Address"
|
|
bitfld.long 0x0 6.--9. " SZ ,Region Size" "1MB section,16MB supersection,Res,Res,Res,Res,Res,Res,64KB page,Res,Res,Res,Res,Res,4KB page,Res"
|
|
bitfld.long 0x0 4.--5. " XRGN ,Extended Region Type" "NC,WBAW,WTNAW,WB"
|
|
textline " "
|
|
bitfld.long 0x0 1.--3. " AP ,Access Permission" "No access,Supervisor only,No user write,Full access,Domain fault encoded,Supervisor read only,Supervisor/User read only,?..."
|
|
bitfld.long 0x0 0. " V ,Valid Bit" "No,Yes"
|
|
group c15:0x525f--0x525f
|
|
line.long 0x0 "MTLBVA,Main TLB VA Register"
|
|
hexmask.long 0x0 10.--31. 0x400 " VA ,Virtual Address"
|
|
hexmask.long.word 0x0 0.--9. 0x1 " PROCESS ,Memory Space Identifier"
|
|
group c15:0x701f--0x701f
|
|
line.long 0x0 "TLBDCR,TLB Debug Control Register"
|
|
bitfld.long 0x0 7. " IMM ,Instruction Main TLB Match" "Ena,Dis"
|
|
bitfld.long 0x0 6. " DMM ,Data Main TLB Match" "Ena,Dis"
|
|
bitfld.long 0x0 5. " IML ,Instruction Main TLB Load" "Ena,Dis"
|
|
bitfld.long 0x0 4. " DML ,Data Main TLB Load" "Ena,Dis"
|
|
bitfld.long 0x0 3. " IUM ,Instruction MicroTLB Match" "Ena,Dis"
|
|
bitfld.long 0x0 2. " DUM ,Data MicroTLB Match" "Ena,Dis"
|
|
bitfld.long 0x0 1. " IUL ,Instruction MicroTLB Load and Flush" "Ena,Dis"
|
|
bitfld.long 0x0 0. " DUL ,Data MicroTLB Load and Flush" "Ena,Dis"
|
|
group c15:0x50ef--0x50ef
|
|
line.long 0x00 "RMTLBMVR,Read Main TLB Master Valid Register"
|
|
hexmask.long 0x00 0.--31. 1. " RMTLBMV ,Read Main TLB Master Valid"
|
|
group c15:0x51ef--0x51ef
|
|
line.long 0x00 "WMTLBMVR,Write Main TLB Master Valid Register"
|
|
hexmask.long 0x00 0.--31. 1. " WMTLBMV ,Write Main TLB Master Valid"
|
|
tree.end
|
|
width 11.
|
|
config 16. 8.
|
|
width 8.
|
|
tree "Debug Register"
|
|
rgroup c14:0x00--0x00
|
|
line.long 0x0 "DIDR,Debug ID Register"
|
|
bitfld.long 0x0 28.--31. " WRP ,Number of Watchpoint Register Pairs" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16"
|
|
bitfld.long 0x0 24.--27. " BRP ,Number of Breakpoint Register Pairs" "Res,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16"
|
|
bitfld.long 0x0 20.--23. " Context ,Number of BRPs with Context ID Comparison Capability" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16"
|
|
textline " "
|
|
bitfld.long 0x0 16.--19. " Version ,Debug Architecture Version" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 4.--7. " Variant ,Implementation-defined Variant Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x0 0.--3. " Revision ,Implementation-defined Revision Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group c14:0x10--0x10
|
|
line.long 0x0 "DSCR,Debug Status and Control Register"
|
|
bitfld.long 0x0 30. " rDTRfull ,rDTR Buffer Full Flag (core read)" "Empty,Full"
|
|
bitfld.long 0x0 29. " wDTRfull ,wDTR Buffer Full Flag (core write)" "Empty,Full"
|
|
bitfld.long 0x0 15. " MONITOR ,Monitor Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 14. " MODE ,Mode Select" "Monitor,Halt"
|
|
textline " "
|
|
bitfld.long 0x0 13. " ARM ,Execute ARM Instruction in ITR" "Disabled,Enabled"
|
|
bitfld.long 0x0 12. " COMMS ,User Mode Access to Comms Channel Disable" "Enabled,Disabled"
|
|
bitfld.long 0x0 11. " INTDIS ,Interrupts Disable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x0 10. " DBGACK ,Force DBGACK Signal High" "No,Yes"
|
|
bitfld.long 0x0 9. " DbgNoPwrdwn ,Powerdown Disable" "Enabled,Disabled"
|
|
bitfld.long 0x0 7. " IABORT ,Sticky Imprecise Data Abort" "No,Yes"
|
|
bitfld.long 0x0 6. " PABORT ,Sticky Precise Data Abort" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 2.--5. " ENTRY ,Method of Entry" "Halt,Breakpoint,Watchpoint,BKPT,EDBGRQ,Vector,DAbort,IAbort,?..."
|
|
bitfld.long 0x0 1. " RESTARTED ,Core Restarted" "No,Yes"
|
|
bitfld.long 0x0 0. " HALTED ,Core Halted" "No,Yes"
|
|
group c14:0x50--0x50
|
|
line.long 0x00 "DTR,Data Transfer Register"
|
|
group c14:0x70--0x70
|
|
line.long 0x0 "VCR,Vector Catch Register"
|
|
bitfld.long 0x0 7. " FIQ ,Vector Catch Enable FIQ" "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " IRQ ,Vector Catch Enable IRQ" "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " DABORT ,Vector Catch Enable Data Abort" "Disabled,Enabled"
|
|
bitfld.long 0x0 3. " PABORT ,Vector Catch Enable Prefetch Abort" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 2. " SWI ,Vector Catch Enable SWI" "Disabled,Enabled"
|
|
bitfld.long 0x0 1. " UNDEF ,Vector Catch Enable Undefined Instruction" "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " RESET ,Vector Catch Enable Reset" "Disabled,Enabled"
|
|
tree.end
|
|
tree "Breakpoints"
|
|
group c14:0x400--0x400
|
|
line.long 0x0 "BVR0,Breakpoint Value Register 0"
|
|
hexmask.long 0x0 2.--31. 0x4 " IVA ,Breakpoint address"
|
|
group c14:0x500--0x500
|
|
line.long 0x0 "BCR0,Breakpoint Control Register 0"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
group c14:0x410--0x410
|
|
line.long 0x0 "BVR1,Breakpoint Value Register 1"
|
|
hexmask.long 0x0 2.--31. 0x4 " IVA ,Breakpoint address"
|
|
group c14:0x510--0x510
|
|
line.long 0x0 "BCR1,Breakpoint Control Register 1"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
group c14:0x420--0x420
|
|
line.long 0x0 "BVR2,Breakpoint Value Register 2"
|
|
hexmask.long 0x0 2.--31. 0x4 " IVA ,Breakpoint address"
|
|
group c14:0x520--0x520
|
|
line.long 0x0 "BCR2,Breakpoint Control Register 2"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
group c14:0x430--0x430
|
|
line.long 0x0 "BVR3,Breakpoint Value Register 3"
|
|
hexmask.long 0x0 2.--31. 0x4 " IVA ,Breakpoint address"
|
|
group c14:0x530--0x530
|
|
line.long 0x0 "BCR3,Breakpoint Control Register 3"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
group c14:0x440--0x440
|
|
line.long 0x0 "BVR4,Breakpoint Value Register 4"
|
|
group c14:0x540--0x540
|
|
line.long 0x0 "BCR4,Breakpoint Control Register 4"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
group c14:0x450--0x450
|
|
line.long 0x0 "BVR5,Breakpoint Value Register 5"
|
|
group c14:0x550--0x550
|
|
line.long 0x0 "BCR5,Breakpoint Control Register 5"
|
|
bitfld.long 0x0 21. " M ,Meaning of the associated BVR" "Address,ContextID"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " B ,Breakpoint Enable" "Disabled,Enabled"
|
|
tree.end
|
|
width 8.
|
|
tree "Watchpoints"
|
|
group c14:0x600--0x600
|
|
line.long 0x0 "WVR0,Watchpoint Value Register 0"
|
|
hexmask.long 0x0 2.--31. 0x4 " WADD ,Watchpoint Address"
|
|
group c14:0x700--0x700
|
|
line.long 0x0 "WCR0,Watchpoint Control Register 0"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 3.--4. " L/S ,Load/Store Access" "Reserved,Load,Store,Load/Store"
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " W ,Watchpoint Enable" "Disabled,Enabled"
|
|
group c14:0x610--0x610
|
|
line.long 0x0 "WVR1,Watchpoint Value Register 1"
|
|
hexmask.long 0x0 2.--31. 0x4 " WADD ,Watchpoint Address"
|
|
group c14:0x710--0x710
|
|
line.long 0x0 "WCR1,Watchpoint Control Register 1"
|
|
bitfld.long 0x0 20. " E ,Enable Linking" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " Linked ,Linked BRP" "BRP0,BRP1,BRP2,BRP3,BRP4,BRP5,BRP6,BRP7,BRP8,BRP9,BRP10,BRP11,BRP12,BRP13,BRP14,BRP15"
|
|
textline " "
|
|
bitfld.long 0x0 8. " Byte3 ,Byte 3 Access Control" "No,Yes"
|
|
bitfld.long 0x0 7. " Byte2 ,Byte 2 Access Control" "No,Yes"
|
|
bitfld.long 0x0 6. " Byte1 ,Byte 1 Access Control" "No,Yes"
|
|
bitfld.long 0x0 5. " Byte0 ,Byte 0 Access Control" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x0 3.--4. " L/S ,Load/Store Access" "Reserved,Load,Store,Load/Store"
|
|
bitfld.long 0x0 1.--2. " S ,Supervisor Access" "Reserved,Privileged,User,Priv/User"
|
|
bitfld.long 0x0 0. " W ,Watchpoint Enable" "Disabled,Enabled"
|
|
tree.end
|
|
width 11.
|
|
width 0xb
|
|
tree.end
|
|
tree.open "IOMUXC (IOMUX Controller)"
|
|
base ad:0x43fac000
|
|
width 29.
|
|
tree "SW_MUX_CTL_PAD Registers"
|
|
group.long 0x04++0x323
|
|
line.long 0x00 "SW_MUX_CTL_PAD_CAPTURE,Software Multiplexer Control Registers (CAPTURE)"
|
|
bitfld.long 0x00 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x00 0.--2. " MUX_MODE ,MUX Mode Select Field" "CAPIN1:gpt,CMPOUT2:gpt,SS1:cspi2,EPITO:epit1,CLK32K:ccm,GPIO[4]:gpio1,?..."
|
|
line.long 0x04 "SW_MUX_CTL_PAD_COMPARE,Software Multiplexer Control Registers (COMPARE)"
|
|
bitfld.long 0x04 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x04 0.--2. " MUX_MODE ,MUX Mode Select Field" "CMPOUT1:gpt,CAPIN2:gpt,CMPOUT3:gpt,EPITO:epit2,Reserved,GPIO[5]:gpio1,Reserved,EXTDMA_2:sdma"
|
|
line.long 0x08 "SW_MUX_CTL_PAD_WDOG_RST,Software Multiplexer Control Registers (WDOG_RST)"
|
|
bitfld.long 0x08 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x08 0.--2. " MUX_MODE ,MUX Mode Select Field" "WDOG_B:wdog,Reserved,Reserved,FLASH_STROBE:ipu,Reserved,GPIO[6]:gpio1,?..."
|
|
line.long 0x0c "SW_MUX_CTL_PAD_GPIO1_0,Software Multiplexer Control Registers (GPIO1_0)"
|
|
bitfld.long 0x0c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x0c 0.--2. " MUX_MODE ,MUX Mode Select Field" "GPIO[0]:gpio1,PMIC_RDY:ccm,LINE:owire,Reserved,Reserved,Reserved,Reserved,EXTDMA_0:sdma"
|
|
line.long 0x10 "SW_MUX_CTL_PAD_GPIO1_1,Software Multiplexer Control Registers (GPIO1_1)"
|
|
bitfld.long 0x10 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x10 0.--2. " MUX_MODE ,MUX Mode Select Field" "GPIO[1]:gpio1,Reserved,PWMO:pwm,SS2:cspi1,Reserved,Reserved,TAMPER_DETECT:scc,EXTDMA_1:sdma"
|
|
line.long 0x14 "SW_MUX_CTL_PAD_GPIO2_0,Software Multiplexer Control Registers (GPIO2_0)"
|
|
bitfld.long 0x14 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x14 0. " MUX_MODE ,MUX Mode Select Field" "GPIO[0]:gpio2,USBOTG_CLK:usb_top"
|
|
line.long 0x18 "SW_MUX_CTL_PAD_GPIO3_0,Software Multiplexer Control Registers (GPIO3_0)"
|
|
bitfld.long 0x18 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x18 0. " MUX_MODE ,MUX Mode Select Field" "GPIO[0]:gpio3,USBH2_CLK:usb_top"
|
|
line.long 0x1c "SW_MUX_CTL_PAD_CLKO,Software Multiplexer Control Registers (CLKO)"
|
|
bitfld.long 0x1c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1c 0.--2. " MUX_MODE ,MUX Mode Select Field" "CLKO:ccm,Reserved,Reserved,Reserved,Reserved,GPIO[8]:gpio1,?..."
|
|
line.long 0x20 "SW_MUX_CTL_PAD_VSTBY,Software Multiplexer Control Registers (VSTBY)"
|
|
bitfld.long 0x20 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x20 0.--2. " MUX_MODE ,MUX Mode Select Field" "VSTBY:ccm,Reserved,Reserved,Reserved,Reserved,GPIO[7]:gpio1,?..."
|
|
line.long 0x24 "SW_MUX_CTL_PAD_A0,Software Multiplexer Control Registers (A0)"
|
|
bitfld.long 0x24 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x28 "SW_MUX_CTL_PAD_A1,Software Multiplexer Control Registers (A1)"
|
|
bitfld.long 0x28 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x2C "SW_MUX_CTL_PAD_A2,Software Multiplexer Control Registers (A2)"
|
|
bitfld.long 0x2C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x30 "SW_MUX_CTL_PAD_A3,Software Multiplexer Control Registers (A3)"
|
|
bitfld.long 0x30 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x34 "SW_MUX_CTL_PAD_A4,Software Multiplexer Control Registers (A4)"
|
|
bitfld.long 0x34 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x38 "SW_MUX_CTL_PAD_A5,Software Multiplexer Control Registers (A5)"
|
|
bitfld.long 0x38 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x3C "SW_MUX_CTL_PAD_A6,Software Multiplexer Control Registers (A6)"
|
|
bitfld.long 0x3C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x40 "SW_MUX_CTL_PAD_A7,Software Multiplexer Control Registers (A7)"
|
|
bitfld.long 0x40 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x44 "SW_MUX_CTL_PAD_A8,Software Multiplexer Control Registers (A8)"
|
|
bitfld.long 0x44 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x48 "SW_MUX_CTL_PAD_A9,Software Multiplexer Control Registers (A9)"
|
|
bitfld.long 0x48 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x4C "SW_MUX_CTL_PAD_A10,Software Multiplexer Control Registers (A10)"
|
|
bitfld.long 0x4C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x50 "SW_MUX_CTL_PAD_MA10,Software Multiplexer Control Registers (MA10)"
|
|
bitfld.long 0x50 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x54 "SW_MUX_CTL_PAD_A11,Software Multiplexer Control Registers (A11)"
|
|
bitfld.long 0x54 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x58 "SW_MUX_CTL_PAD_A12,Software Multiplexer Control Registers (A12)"
|
|
bitfld.long 0x58 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x5C "SW_MUX_CTL_PAD_A13,Software Multiplexer Control Registers (A13)"
|
|
bitfld.long 0x5C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x60 "SW_MUX_CTL_PAD_A14,Software Multiplexer Control Registers (A14)"
|
|
bitfld.long 0x60 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x64 "SW_MUX_CTL_PAD_A15,Software Multiplexer Control Registers (A15)"
|
|
bitfld.long 0x64 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x68 "SW_MUX_CTL_PAD_A16,Software Multiplexer Control Registers (A16)"
|
|
bitfld.long 0x68 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x6C "SW_MUX_CTL_PAD_A17,Software Multiplexer Control Registers (A17)"
|
|
bitfld.long 0x6C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x70 "SW_MUX_CTL_PAD_A18,Software Multiplexer Control Registers (A18)"
|
|
bitfld.long 0x70 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x74 "SW_MUX_CTL_PAD_A19,Software Multiplexer Control Registers (A19)"
|
|
bitfld.long 0x74 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x78 "SW_MUX_CTL_PAD_A20,Software Multiplexer Control Registers (A20)"
|
|
bitfld.long 0x78 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x7C "SW_MUX_CTL_PAD_A21,Software Multiplexer Control Registers (A21)"
|
|
bitfld.long 0x7C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x80 "SW_MUX_CTL_PAD_A22,Software Multiplexer Control Registers (A22)"
|
|
bitfld.long 0x80 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x84 "SW_MUX_CTL_PAD_A23,Software Multiplexer Control Registers (A23)"
|
|
bitfld.long 0x84 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x88 "SW_MUX_CTL_PAD_A24,Software Multiplexer Control Registers (A24)"
|
|
bitfld.long 0x88 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x8C "SW_MUX_CTL_PAD_A25,Software Multiplexer Control Registers (A25)"
|
|
bitfld.long 0x8C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x90 "SW_MUX_CTL_PAD_EB0,Software Multiplexer Control Registers (EB0)"
|
|
bitfld.long 0x90 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x94 "SW_MUX_CTL_PAD_EB1,Software Multiplexer Control Registers (EB1)"
|
|
bitfld.long 0x94 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x98 "SW_MUX_CTL_PAD_OE,Software Multiplexer Control Registers (OE)"
|
|
bitfld.long 0x98 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0x9C "SW_MUX_CTL_PAD_CS0,Software Multiplexer Control Registers (CS0)"
|
|
bitfld.long 0x9C 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xa0 "SW_MUX_CTL_PAD_CS1,Software Multiplexer Control Registers (CS1)"
|
|
bitfld.long 0xa0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xa0 0.--1. " MUX_MODE ,MUX Mode Select Field" "EIM_CS1:emi,Reserved,Reserved,NANDF_CE3:emi"
|
|
line.long 0xa4 "SW_MUX_CTL_PAD_CS2,Software Multiplexer Control Registers (CS2)"
|
|
bitfld.long 0xa4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xa8 "SW_MUX_CTL_PAD_CS3,Software Multiplexer Control Registers (CS3)"
|
|
bitfld.long 0xa8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xac "SW_MUX_CTL_PAD_CS4,Software Multiplexer Control Registers (CS4)"
|
|
bitfld.long 0xac 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xac 0.--2. " MUX_MODE ,MUX Mode Select Field" "EIM_CS4:emi,DTACK_B:emi,Reserved,NANDF_CE1:emi,Reserved,GPIO[20]:gpio1,?..."
|
|
line.long 0xb0 "SW_MUX_CTL_PAD_CS5,Software Multiplexer Control Registers (CS5)"
|
|
bitfld.long 0xb0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xb0 0.--2. " MUX_MODE ,MUX Mode Select Field" "EIM_CS5:emi,SS2:cspi2,SS2:cspi1,NANDF_CE2:emi,Reserved,GPIO[21]:gpio1,?..."
|
|
line.long 0xb4 "SW_MUX_CTL_PAD_NF_CE0,Software Multiplexer Control Registers (NF_CE0)"
|
|
bitfld.long 0xb4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xb4 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_CE0:emi,Reserved,Reserved,Reserved,Reserved,GPIO[22]:gpio1,?..."
|
|
line.long 0xb8 "SW_MUX_CTL_PAD_LBA,Software Multiplexer Control Registers (LBA)"
|
|
bitfld.long 0xb8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xbc "SW_MUX_CTL_PAD_BCLK,Software Multiplexer Control Registers (BCLK)"
|
|
bitfld.long 0xbc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xc0 "SW_MUX_CTL_PAD_RW,Software Multiplexer Control Registers (RW)"
|
|
bitfld.long 0xc0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
line.long 0xc4 "SW_MUX_CTL_PAD_NFWE_B,Software Multiplexer Control Registers (NFWE_B)"
|
|
bitfld.long 0xc4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xc4 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_WE_B:emi,USBH2_DATA[3]:usb_top,DISPB_D0_VSYNC:ipu,Reserved,Reserved,GPIO[18]:gpio2,Reserved,TRACE[0]:arm11p_top"
|
|
line.long 0xc8 "SW_MUX_CTL_PAD_NFRE_B,Software Multiplexer Control Registers (NFRE_B)"
|
|
bitfld.long 0xc8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xc8 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_RE_B:emi,USBH2_DIR:usb_top,DISPB_BCLK:ipu,Reserved,Reserved,GPIO[19]:gpio2,Reserved,TRACE[1]:arm11p_top"
|
|
line.long 0xcc "SW_MUX_CTL_PAD_NFALE,Software Multiplexer Control Registers (NFALE)"
|
|
bitfld.long 0xcc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xcc 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_ALE:emi,USBH2_STP:usb_top,DISPB_CS0:ipu,Reserved,Reserved,GPIO[20]:gpio2,Reserved,TRACE[2]:arm11p_top"
|
|
line.long 0xd0 "SW_MUX_CTL_PAD_NFCLE,Software Multiplexer Control Registers (NFCLE)"
|
|
bitfld.long 0xd0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xd0 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_CLE:emi,USBH2_NXT:usb_top,DISPB_PAR_RS:ipu,Reserved,Reserved,GPIO[21]:gpio2,Reserved,TRACE[3]:arm11p_top"
|
|
line.long 0xd4 "SW_MUX_CTL_PAD_NFWP_B,Software Multiplexer Control Registers (NFWP_B)"
|
|
bitfld.long 0xd4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xd4 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_WP_B:emi,USBH2_DATA[7]:usb_top,DISPB_WR:ipu,Reserved,Reserved,GPIO[22]:gpio2,Reserved,TRCTL:arm11p_top"
|
|
line.long 0xd8 "SW_MUX_CTL_PAD_NFRB,Software Multiplexer Control Registers (NFRB)"
|
|
bitfld.long 0xd8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xd8 0.--2. " MUX_MODE ,MUX Mode Select Field" "NANDF_RB:emi,Reserved,DISPB_RD:ipu,Reserved,Reserved,GPIO[23]:gpio2,Reserved,TRCLK:arm11p_top"
|
|
line.long 0xdc "SW_MUX_CTL_PAD_CSI_D8,Software Multiplexer Control Registers (CSI_D8)"
|
|
bitfld.long 0xdc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xdc 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[8]:ipu,COL[0]:kpp,Reserved,Reserved,Reserved,GPIO[20]:gpio1,Reserved,EVNTBUS[13]:arm11p_top"
|
|
line.long 0xe0 "SW_MUX_CTL_PAD_CSI_D9,Software Multiplexer Control Registers (CSI_D9)"
|
|
bitfld.long 0xe0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xe0 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[9]:ipu,COL[1]:kpp,Reserved,Reserved,Reserved,GPIO[21]:gpio1,Reserved,EVNTBUS[14]:arm11p_top"
|
|
line.long 0xe4 "SW_MUX_CTL_PAD_CSI_D10,Software Multiplexer Control Registers (CSI_D10)"
|
|
bitfld.long 0xe4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xe4 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[10]:ipu,COL[2]:kpp,Reserved,Reserved,Reserved,GPIO[22]:gpio1,Reserved,EVNTBUS[15]:arm11p_top"
|
|
line.long 0xe8 "SW_MUX_CTL_PAD_CSI_D11,Software Multiplexer Control Registers (CSI_D11)"
|
|
bitfld.long 0xe8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xe8 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[11]:ipu,COL[3]:kpp,Reserved,Reserved,Reserved,GPIO[23]:gpio1,?..."
|
|
line.long 0xec "SW_MUX_CTL_PAD_CSI_D12,Software Multiplexer Control Registers (CSI_D12)"
|
|
bitfld.long 0xec 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xec 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[12]:ipu,ROW[0]:kpp,Reserved,Reserved,Reserved,GPIO[24]:gpio1,?..."
|
|
line.long 0xf0 "SW_MUX_CTL_PAD_CSI_D13,Software Multiplexer Control Registers (CSI_D13)"
|
|
bitfld.long 0xf0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xf0 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[13]:ipu,ROW[1]:kpp,Reserved,Reserved,Reserved,GPIO[25]:gpio1,?..."
|
|
line.long 0xf4 "SW_MUX_CTL_PAD_CSI_D14,Software Multiplexer Control Registers (CSI_D14)"
|
|
bitfld.long 0xf4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xf4 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[14]:ipu,ROW[2]:kpp,Reserved,Reserved,Reserved,GPIO[26]:gpio1,?..."
|
|
line.long 0xf8 "SW_MUX_CTL_PAD_CSI_D15,Software Multiplexer Control Registers (CSI_D15)"
|
|
bitfld.long 0xf8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xf8 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_D[15]:ipu,ROW[3]:kpp,Reserved,Reserved,Reserved,GPIO[27]:gpio1,?..."
|
|
line.long 0xfc "SW_MUX_CTL_PAD_CSI_MCLK,Software Multiplexer Control Registers (CSI_MCLK)"
|
|
bitfld.long 0xfc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0xfc 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_MCLK:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[28]:gpio1,?..."
|
|
line.long 0x100 "SW_MUX_CTL_PAD_CSI_VSYNC,Software Multiplexer Control Registers (CSI_VSYNC)"
|
|
bitfld.long 0x100 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x100 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_VSYNC:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[29]:gpio1,?..."
|
|
line.long 0x104 "SW_MUX_CTL_PAD_CSI_HSYNC,Software Multiplexer Control Registers (CSI_HSYNC)"
|
|
bitfld.long 0x104 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x104 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_HSYNC:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[30]:gpio1,?..."
|
|
line.long 0x108 "SW_MUX_CTL_PAD_CSI_PIXCLK,Software Multiplexer Control Registers (CSI_PIXCLK)"
|
|
bitfld.long 0x108 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x108 0.--2. " MUX_MODE ,MUX Mode Select Field" "CSI_PIXCLK:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[31]:gpio1,?..."
|
|
line.long 0x10c "SW_MUX_CTL_PAD_I2C1_CLK,Software Multiplexer Control Registers (I2C1_CLK)"
|
|
bitfld.long 0x10c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x10c 0.--2. " MUX_MODE ,MUX Mode Select Field" "SCL:i2c1,Reserved,Reserved,Reserved,Reserved,GPIO[24]:gpio2,USB_BYP_CLK:ccm,?..."
|
|
line.long 0x110 "SW_MUX_CTL_PAD_I2C1_DAT,Software Multiplexer Control Registers (I2C1_DAT)"
|
|
bitfld.long 0x110 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x110 0.--2. " MUX_MODE ,MUX Mode Select Field" "SDA:i2c1,Reserved,Reserved,Reserved,Reserved,GPIO[25]:gpio2,?..."
|
|
line.long 0x114 "SW_MUX_CTL_PAD_I2C2_CLK,Software Multiplexer Control Registers (I2C2_CLK)"
|
|
bitfld.long 0x114 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x114 0.--2. " MUX_MODE ,MUX Mode Select Field" "SCL:i2c2,TXCAN:can1,USBH2_PWR:usb_top,Reserved,Reserved,GPIO[26]:gpio2,DEBUG_BUS_DEVICE[2]:sdma,?..."
|
|
line.long 0x118 "SW_MUX_CTL_PAD_I2C2_DAT,Software Multiplexer Control Registers (I2C2_DAT)"
|
|
bitfld.long 0x118 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x118 0.--2. " MUX_MODE ,MUX Mode Select Field" "SDA:i2c2,RXCAN:can1,USBH2_OC:usb_top,Reserved,Reserved,GPIO[27]:gpio2,DEBUG_BUS_DEVICE[3]:sdma,?..."
|
|
line.long 0x11c "SW_MUX_CTL_PAD_STXD4,Software Multiplexer Control Registers (STXD4)"
|
|
bitfld.long 0x11c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x11c 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD4_TXD:audmux,Reserved,Reserved,Reserved,Reserved,GPIO[28]:gpio2,Reserved,ARM_COREASID0:arm11p_top"
|
|
line.long 0x120 "SW_MUX_CTL_PAD_SRXD4,Software Multiplexer Control Registers (SRXD4)"
|
|
bitfld.long 0x120 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x120 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD4_RXD:audmux,Reserved,Reserved,Reserved,Reserved,GPIO[29]:gpio2,Reserved,ARM_COREASID1:arm11p_top"
|
|
line.long 0x124 "SW_MUX_CTL_PAD_SCK4,Software Multiplexer Control Registers (SCK4)"
|
|
bitfld.long 0x124 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x124 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD4_TXC:audmux,Reserved,Reserved,Reserved,Reserved,GPIO[30]:gpio2,Reserved,ARM_COREASID2:arm11p_top"
|
|
line.long 0x128 "SW_MUX_CTL_PAD_STXFS4,Software Multiplexer Control Registers (STXFS4)"
|
|
bitfld.long 0x128 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x128 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD4_TXFS:audmux,Reserved,Reserved,Reserved,Reserved,GPIO[31]:gpio2,Reserved,ARM_COREASID3:arm11p_top"
|
|
line.long 0x12c "SW_MUX_CTL_PAD_STXD5,Software Multiplexer Control Registers (STXD5)"
|
|
bitfld.long 0x12c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x12c 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD5_TXD:audmux,SPDIF_OUT1:spdif,MOSI:cspi2,Reserved,Reserved,GPIO[0]:gpio1,Reserved,ARM_COREASID4:arm11p_top"
|
|
line.long 0x130 "SW_MUX_CTL_PAD_SRXD5,Software Multiplexer Control Registers (SRXD5)"
|
|
bitfld.long 0x130 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x130 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD5_RXD:audmux,SPDIF_IN1:spdif,MISO:cspi2,Reserved,Reserved,GPIO[1]:gpio1,Reserved,ARM_COREASID5:arm11p_top"
|
|
line.long 0x134 "SW_MUX_CTL_PAD_SCK5,Software Multiplexer Control Registers (SCK5)"
|
|
bitfld.long 0x134 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x134 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD5_TXC:audmux,SPDIF_EXTCLK:spdif,SCLK:cspi2,Reserved,Reserved,GPIO[2]:gpio1,Reserved,ARM_COREASID6:arm11p_top"
|
|
line.long 0x138 "SW_MUX_CTL_PAD_STXFS5,Software Multiplexer Control Registers (STXFS5)"
|
|
bitfld.long 0x138 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x138 0.--2. " MUX_MODE ,MUX Mode Select Field" "AUD5_TXFS:audmux,Reserved,RDY:cspi2,Reserved,Reserved,GPIO[3]:gpio1,Reserved,ARM_COREASID7:arm11p_top"
|
|
line.long 0x13c "SW_MUX_CTL_PAD_SCKR,Software Multiplexer Control Registers (SCKR)"
|
|
bitfld.long 0x13c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x13c 0.--2. " MUX_MODE ,MUX Mode Select Field" "SCKR:esai,Reserved,Reserved,Reserved,Reserved,GPIO[4]:gpio1,Reserved,EVNTBUS[10]:arm11p_top"
|
|
line.long 0x140 "SW_MUX_CTL_PAD_FSR,Software Multiplexer Control Registers (FSR)"
|
|
bitfld.long 0x140 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x140 0.--2. " MUX_MODE ,MUX Mode Select Field" "FSR:esai,Reserved,Reserved,Reserved,Reserved,GPIO[5]:gpio1,Reserved,EVNTBUS[11]:arm11p_top"
|
|
line.long 0x144 "SW_MUX_CTL_PAD_HCKR,Software Multiplexer Control Registers (HCKR)"
|
|
bitfld.long 0x144 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x144 0.--2. " MUX_MODE ,MUX Mode Select Field" "HCKR:esai,AUD5_RXFS:audmux,SS0:cspi2,FLASH_STROBE:ipu,Reserved,GPIO[6]:gpio1,Reserved,EVNTBUS[12]:arm11p_top"
|
|
line.long 0x148 "SW_MUX_CTL_PAD_SCKT,Software Multiplexer Control Registers (SCKT)"
|
|
bitfld.long 0x148 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x148 0.--2. " MUX_MODE ,MUX Mode Select Field" "SCKT:esai,Reserved,Reserved,Reserved,Reserved,GPIO[7]:gpio1,CSI_D[0]:ipu,ROW[2]:kpp"
|
|
line.long 0x14c "SW_MUX_CTL_PAD_FST,Software Multiplexer Control Registers (FST)"
|
|
bitfld.long 0x14c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x14c 0.--2. " MUX_MODE ,MUX Mode Select Field" "FST:esai,Reserved,Reserved,Reserved,Reserved,GPIO[8]:gpio1,CSI_D[1]:ipu,ROW[3]:kpp"
|
|
line.long 0x150 "SW_MUX_CTL_PAD_HCKT,Software Multiplexer Control Registers (HCKT)"
|
|
bitfld.long 0x150 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x150 0.--2. " MUX_MODE ,MUX Mode Select Field" "HCKT:esai,AUD5_RXC:audmux,Reserved,Reserved,Reserved,GPIO[9]:gpio1,CSI_D[2]:ipu,COL[3]:kpp"
|
|
line.long 0x154 "SW_MUX_CTL_PAD_TX5_RX0,Software Multiplexer Control Registers (TX5_RX0)"
|
|
bitfld.long 0x154 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x154 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX5_RX0:esai,AUD4_RXC:audmux,SS2:cspi2,TXCAN:can2,DTR:uart2,GPIO[10]:gpio1,Reserved,M3IF_CHOSEN_MASTER_0:emi"
|
|
line.long 0x158 "SW_MUX_CTL_PAD_TX4_RX1,Software Multiplexer Control Registers (TX4_RX1)"
|
|
bitfld.long 0x158 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x158 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX4_RX1:esai,AUD4_RXFS:audmux,SS3:cspi2,RXCAN:can2,DSR:uart2,GPIO[11]:gpio1,CSI_D[3]:ipu,ROW[0]:kpp"
|
|
line.long 0x15c "SW_MUX_CTL_PAD_TX3_RX2,Software Multiplexer Control Registers (TX3_RX2)"
|
|
bitfld.long 0x15c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x15c 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX3_RX2:esai,SCL:i2c3,Reserved,NANDF_CE1:emi,Reserved,GPIO[12]:gpio1,CSI_D[4]:ipu,ROW[1]:kpp"
|
|
line.long 0x160 "SW_MUX_CTL_PAD_TX2_RX3,Software Multiplexer Control Registers (TX2_RX3)"
|
|
bitfld.long 0x160 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x160 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX2_RX3:esai,SDA:i2c3,Reserved,NANDF_CE2:emi,Reserved,GPIO[13]:gpio1,CSI_D[5]:ipu,COL[0]:kpp"
|
|
line.long 0x164 "SW_MUX_CTL_PAD_TX1,Software Multiplexer Control Registers (TX1)"
|
|
bitfld.long 0x164 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x164 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX1:esai,PMIC_RDY:ccm,SS2:cspi1,NANDF_CE3:emi,RI:uart2,GPIO[14]:gpio1,CSI_D[6]:ipu,COL[1]:kpp"
|
|
line.long 0x168 "SW_MUX_CTL_PAD_TX0,Software Multiplexer Control Registers (TX0)"
|
|
bitfld.long 0x168 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x168 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX0:esai,SPDIF_EXTCLK:spdif,SS3:cspi1,DTACK_B:emi,DCD:uart2,GPIO[15]:gpio1,CSI_D[7]:ipu,COL[2]:kpp"
|
|
line.long 0x16c "SW_MUX_CTL_PAD_CSPI1_MOSI,Software Multiplexer Control Registers (CSPI1_MOSI)"
|
|
bitfld.long 0x16c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x16c 0.--2. " MUX_MODE ,MUX Mode Select Field" "MOSI:cspi1,Reserved,Reserved,Reserved,Reserved,GPIO[16]:gpio1,Reserved,CTI_TRIG_OUT1_2:ect"
|
|
line.long 0x170 "SW_MUX_CTL_PAD_CSPI1_MISO,Software Multiplexer Control Registers (CSPI1_MISO)"
|
|
bitfld.long 0x170 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x170 0.--2. " MUX_MODE ,MUX Mode Select Field" "MISO:cspi1,Reserved,Reserved,Reserved,Reserved,GPIO[17]:gpio1,Reserved,CTI_TRIG_OUT1_3:ect"
|
|
line.long 0x174 "SW_MUX_CTL_PAD_CSPI1_SS0,Software Multiplexer Control Registers (CSPI1_SS0)"
|
|
bitfld.long 0x174 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x174 0.--2. " MUX_MODE ,MUX Mode Select Field" "SS0:cspi1,LINE:owire,SS3:cspi2,Reserved,Reserved,GPIO[18]:gpio1,Reserved,CTI_TRIG_OUT1_4:ect"
|
|
line.long 0x178 "SW_MUX_CTL_PAD_CSPI1_SS1,Software Multiplexer Control Registers (CSPI1_SS1)"
|
|
bitfld.long 0x178 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x178 0.--2. " MUX_MODE ,MUX Mode Select Field" "SS1:cspi1,PWMO:pwm,CLK32K:ccm,Reserved,Reserved,GPIO[19]:gpio1,DIAGB[29]:ipu,CTI_TRIG_OUT1_5:ect"
|
|
line.long 0x17c "SW_MUX_CTL_PAD_CSPI1_SCLK,Software Multiplexer Control Registers (CSPI1_SCLK)"
|
|
bitfld.long 0x17c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x17c 0.--2. " MUX_MODE ,MUX Mode Select Field" "SCLK:cspi1,Reserved,Reserved,Reserved,Reserved,GPIO[4]:gpio3,DIAGB[30]:ipu,M3IF_CHOSEN_MASTER_1:emi"
|
|
line.long 0x180 "SW_MUX_CTL_PAD_CSPI1_SPI_RDY,Software Multiplexer Control Registers (CSPI1_SPI_RDY)"
|
|
bitfld.long 0x180 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x180 0.--2. " MUX_MODE ,MUX Mode Select Field" "RDY:cspi1,Reserved,Reserved,Reserved,Reserved,GPIO[5]:gpio3,DIAGB[31]:ipu,M3IF_CHOSEN_MASTER_2:emi"
|
|
line.long 0x184 "SW_MUX_CTL_PAD_RXD1,Software Multiplexer Control Registers (RXD1)"
|
|
bitfld.long 0x184 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x184 0.--2. " MUX_MODE ,MUX Mode Select Field" "RXD_MUX:uart1,MOSI:cspi2,Reserved,Reserved,COL[4]:kpp,GPIO[6]:gpio3,Reserved,EVNTBUS[16]:arm11p_top"
|
|
line.long 0x188 "SW_MUX_CTL_PAD_TXD1,Software Multiplexer Control Registers (TXD1)"
|
|
bitfld.long 0x188 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x188 0.--2. " MUX_MODE ,MUX Mode Select Field" "TXD_MUX:uart1,MISO:cspi2,Reserved,Reserved,COL[5]:kpp,GPIO[7]:gpio3,Reserved,EVNTBUS[17]:arm11p_top"
|
|
line.long 0x18c "SW_MUX_CTL_PAD_RTS1,Software Multiplexer Control Registers (RTS1)"
|
|
bitfld.long 0x18c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x18c 0.--2. " MUX_MODE ,MUX Mode Select Field" "RTS:uart1,SCLK:cspi2,SCL:i2c3,CSI_D[0]:ipu,COL[6]:kpp,GPIO[8]:gpio3,NANDF_CE1:emi,EVNTBUS[18]:arm11p_top"
|
|
line.long 0x190 "SW_MUX_CTL_PAD_CTS1,Software Multiplexer Control Registers (CTS1)"
|
|
bitfld.long 0x190 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x190 0.--2. " MUX_MODE ,MUX Mode Select Field" "CTS:uart1,RDY:cspi2,SDA:i2c3,CSI_D[1]:ipu,COL[7]:kpp,GPIO[9]:gpio3,NANDF_CE2:emi,EVNTBUS[19]:arm11p_top"
|
|
line.long 0x194 "SW_MUX_CTL_PAD_RXD2,Software Multiplexer Control Registers (RXD2)"
|
|
bitfld.long 0x194 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x194 0.--2. " MUX_MODE ,MUX Mode Select Field" "RXD_MUX:uart2,Reserved,Reserved,Reserved,ROW[4]:kpp,GPIO[10]:gpio3,?..."
|
|
line.long 0x198 "SW_MUX_CTL_PAD_TXD2,Software Multiplexer Control Registers (TXD2)"
|
|
bitfld.long 0x198 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x198 0.--2. " MUX_MODE ,MUX Mode Select Field" "TXD_MUX:uart2,SPDIF_EXTCLK:spdif,Reserved,Reserved,ROW[5]:kpp,GPIO[11]:gpio3,?..."
|
|
line.long 0x19c "SW_MUX_CTL_PAD_RTS2,Software Multiplexer Control Registers (RTS2)"
|
|
bitfld.long 0x19c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x19c 0.--2. " MUX_MODE ,MUX Mode Select Field" "RTS:uart2,SPDIF_IN1:spdif,RXCAN:can2,CSI_D[2]:ipu,ROW[6]:kpp,GPIO[12]:gpio3,AUD5_RXC:audmux,RXD_MUX:uart3"
|
|
line.long 0x1a0 "SW_MUX_CTL_PAD_CTS2,Software Multiplexer Control Registers (CTS2)"
|
|
bitfld.long 0x1a0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1a0 0.--2. " MUX_MODE ,MUX Mode Select Field" "CTS:uart2,SPDIF_OUT1:spdif,TXCAN:can2,CSI_D[3]:ipu,ROW[7]:kpp,GPIO[13]:gpio3,AUD5_RXFS:audmux,TXD_MUX:uart3"
|
|
line.long 0x1a4 "SW_MUX_CTL_PAD_USBOTG_PWR,Software Multiplexer Control Registers (USBOTG_PWR)"
|
|
bitfld.long 0x1a4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1a4 0.--2. " MUX_MODE ,MUX Mode Select Field" "USBOTG_PWR:usb_top,USBH2_PWR:usb_top,Reserved,Reserved,Reserved,GPIO[14]:gpio3,?..."
|
|
line.long 0x1a8 "SW_MUX_CTL_PAD_USBOTG_OC,Software Multiplexer Control Registers (USBOTG_OC)"
|
|
bitfld.long 0x1a8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1a8 0.--2. " MUX_MODE ,MUX Mode Select Field" "USBOTG_OC:usb_top,USBH2_OC:usb_top,Reserved,Reserved,Reserved,GPIO[15]:gpio3,?..."
|
|
line.long 0x1ac "SW_MUX_CTL_PAD_LD0,Software Multiplexer Control Registers (LD0)"
|
|
bitfld.long 0x1ac 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1ac 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[0]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[0]:gpio2,SDMA_DEBUG_PC_0:sdma,?..."
|
|
line.long 0x1b0 "SW_MUX_CTL_PAD_LD1,Software Multiplexer Control Registers (LD1)"
|
|
bitfld.long 0x1b0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1b0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[1]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[1]:gpio2,SDMA_DEBUG_PC_1:sdma,?..."
|
|
line.long 0x1b4 "SW_MUX_CTL_PAD_LD2,Software Multiplexer Control Registers (LD2)"
|
|
bitfld.long 0x1b4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1b4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[2]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[2]:gpio2,SDMA_DEBUG_PC_2:sdma,?..."
|
|
line.long 0x1b8 "SW_MUX_CTL_PAD_LD3,Software Multiplexer Control Registers (LD3)"
|
|
bitfld.long 0x1b8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1b8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[3]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[3]:gpio2,SDMA_DEBUG_PC_3:sdma,?..."
|
|
line.long 0x1bc "SW_MUX_CTL_PAD_LD4,Software Multiplexer Control Registers (LD4)"
|
|
bitfld.long 0x1bc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1bc 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[4]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[4]:gpio2,SDMA_DEBUG_PC_4:sdma,?..."
|
|
line.long 0x1c0 "SW_MUX_CTL_PAD_LD5,Software Multiplexer Control Registers (LD5)"
|
|
bitfld.long 0x1c0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1c0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[5]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[5]:gpio2,SDMA_DEBUG_PC_5:sdma,?..."
|
|
line.long 0x1c4 "SW_MUX_CTL_PAD_LD6,Software Multiplexer Control Registers (LD6)"
|
|
bitfld.long 0x1c4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1c4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[6]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[6]:gpio2,SDMA_DEBUG_PC_6:sdma,?..."
|
|
line.long 0x1c8 "SW_MUX_CTL_PAD_LD7,Software Multiplexer Control Registers (LD7)"
|
|
bitfld.long 0x1c8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1c8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[7]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[7]:gpio2,SDMA_DEBUG_PC_7:sdma,?..."
|
|
line.long 0x1cc "SW_MUX_CTL_PAD_LD8,Software Multiplexer Control Registers (LD8)"
|
|
bitfld.long 0x1cc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1cc 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[8]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[8]:gpio2,SDMA_DEBUG_PC_8:sdma,?..."
|
|
line.long 0x1d0 "SW_MUX_CTL_PAD_LD9,Software Multiplexer Control Registers (LD9)"
|
|
bitfld.long 0x1d0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1d0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[9]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[9]:gpio2,SDMA_DEBUG_PC_9:sdma,?..."
|
|
line.long 0x1d4 "SW_MUX_CTL_PAD_LD10,Software Multiplexer Control Registers (LD10)"
|
|
bitfld.long 0x1d4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1d4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[10]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[10]:gpio2,SDMA_DEBUG_PC_10:sdma,?..."
|
|
line.long 0x1d8 "SW_MUX_CTL_PAD_LD11,Software Multiplexer Control Registers (LD11)"
|
|
bitfld.long 0x1d8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1d8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[11]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[11]:gpio2,SDMA_DEBUG_PC_11:sdma,TRACE[4]:arm11p_top"
|
|
line.long 0x1dc "SW_MUX_CTL_PAD_LD12,Software Multiplexer Control Registers (LD12)"
|
|
bitfld.long 0x1dc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1dc 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[12]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[12]:gpio2,SDMA_DEBUG_PC_12:sdma,TRACE[5]:arm11p_top"
|
|
line.long 0x1e0 "SW_MUX_CTL_PAD_LD13,Software Multiplexer Control Registers (LD13)"
|
|
bitfld.long 0x1e0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1e0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[13]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[13]:gpio2,SDMA_DEBUG_PC_13:sdma,TRACE[6]:arm11p_top"
|
|
line.long 0x1e4 "SW_MUX_CTL_PAD_LD14,Software Multiplexer Control Registers (LD14)"
|
|
bitfld.long 0x1e4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1e4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[14]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[14]:gpio2,SDMA_DEBUG_EVENT_CHANNEL_0:sdma,TRACE[7]:arm11p_top"
|
|
line.long 0x1e8 "SW_MUX_CTL_PAD_LD15,Software Multiplexer Control Registers (LD15)"
|
|
bitfld.long 0x1e8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1e8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[15]:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[15]:gpio2,SDMA_DEBUG_EVENT_CHANNEL_1:sdma,TRACE[8]:arm11p_top"
|
|
line.long 0x1ec "SW_MUX_CTL_PAD_LD16,Software Multiplexer Control Registers (LD16)"
|
|
bitfld.long 0x1ec 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1ec 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[16]:ipu,Reserved,DISPB_D12_VSYNC:ipu,Reserved,Reserved,GPIO[16]:gpio2,SDMA_DEBUG_EVENT_CHANNEL_2:sdma,TRACE[9]:arm11p_top"
|
|
line.long 0x1f0 "SW_MUX_CTL_PAD_LD17,Software Multiplexer Control Registers (LD17)"
|
|
bitfld.long 0x1f0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1f0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[17]:ipu,Reserved,DISPB_CS2:ipu,Reserved,Reserved,GPIO[17]:gpio2,SDMA_DEBUG_EVENT_CHANNEL_3:sdma,TRACE[10]:arm11p_top"
|
|
line.long 0x1f4 "SW_MUX_CTL_PAD_LD18,Software Multiplexer Control Registers (LD18)"
|
|
bitfld.long 0x1f4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1f4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[18]:ipu,DISPB_D0_VSYNC:ipu,DISPB_D12_VSYNC:ipu,CMD:esdhc3,USBOTG_DATA[3]:usb_top,GPIO[24]:gpio3,SDMA_DEBUG_EVENT_CHANNEL_4:sdma,TRACE[11]:arm11p_top"
|
|
line.long 0x1f8 "SW_MUX_CTL_PAD_LD19,Software Multiplexer Control Registers (LD19)"
|
|
bitfld.long 0x1f8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1f8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[19]:ipu,DISPB_BCLK:ipu,DISPB_CS1:ipu,CLK:esdhc3,USBOTG_DIR:usb_top,GPIO[25]:gpio3,SDMA_DEBUG_EVENT_CHANNEL_5:sdma,TRACE[12]:arm11p_top"
|
|
line.long 0x1fc "SW_MUX_CTL_PAD_LD20,Software Multiplexer Control Registers (LD20)"
|
|
bitfld.long 0x1fc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x1fc 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[20]ipu:,DISPB_CS0:ipu,DISPB_SD_CLK:ipu,DAT0:esdhc3,Reserved,GPIO[26]:gpio3,SDMA_DEBUG_CORE_STATUS_3:sdma,TRACE[13]:arm11p_top"
|
|
line.long 0x200 "SW_MUX_CTL_PAD_LD21,Software Multiplexer Control Registers (LD21)"
|
|
bitfld.long 0x200 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x200 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[21]:ipu,DISPB_PAR_RS:ipu,DISPB_SER_RS:ipu,DAT1:esdhc3,USBOTG_STP:usb_top,GPIO[27]:gpio3,DEBUG_EVENT_CHANNEL_SEL:sdma,TRACE[14]:arm11p_top"
|
|
line.long 0x204 "SW_MUX_CTL_PAD_LD22,Software Multiplexer Control Registers (LD22)"
|
|
bitfld.long 0x204 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x204 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[22]:ipu,DISPB_WR:ipu,DISPB_SD_D_I:ipu,DAT2:esdhc3,USBOTG_NXT:usb_top,GPIO[28]:gpio3,DEBUG_BUS_ERROR:sdma,TRCTL:arm11p_top"
|
|
line.long 0x208 "SW_MUX_CTL_PAD_LD23,Software Multiplexer Control Registers (LD23)"
|
|
bitfld.long 0x208 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x208 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_DAT[23]:ipu,DISPB_RD:ipu,DISPB_SD_D_IO:ipu,DAT3:esdhc3,USBOTG_DATA[7]:usb_top,GPIO[29]:gpio3,DEBUG_MATCHED_DMBUS:sdma,TRCLK:arm11p_top"
|
|
line.long 0x20c "SW_MUX_CTL_PAD_D3_HSYNC,Software Multiplexer Control Registers (D3_HSYNC)"
|
|
bitfld.long 0x20c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x20c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_HSYNC:ipu,Reserved,DISPB_SD_D_IO:ipu,Reserved,Reserved,GPIO[30]:gpio3,DEBUG_RTBUFFER_WRITE:sdma,TRACE[15]:arm11p_top"
|
|
line.long 0x210 "SW_MUX_CTL_PAD_D3_FPSHIFT,Software Multiplexer Control Registers (D3_FPSHIFT)"
|
|
bitfld.long 0x210 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x210 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_CLK:ipu,Reserved,DISPB_SD_CLK:ipu,Reserved,Reserved,GPIO[31]:gpio3,SDMA_DEBUG_CORE_STATUS_0:sdma,TRACE[16]:arm11p_top"
|
|
line.long 0x214 "SW_MUX_CTL_PAD_D3_DRDY,Software Multiplexer Control Registers (D3_DRDY)"
|
|
bitfld.long 0x214 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x214 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_DRDY:ipu,Reserved,DISPB_SD_D_O:ipu,Reserved,Reserved,GPIO[0]:gpio1,SDMA_DEBUG_CORE_STATUS_1:sdma,TRACE[17]:arm11p_top"
|
|
line.long 0x218 "SW_MUX_CTL_PAD_CONTRAST,Software Multiplexer Control Registers (CONTRAST)"
|
|
bitfld.long 0x218 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x218 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_CONTR:ipu,Reserved,Reserved,Reserved,Reserved,GPIO[1]:gpio1,SDMA_DEBUG_CORE_STATUS_2:sdma,TRACE[18]:arm11p_top"
|
|
line.long 0x21c "SW_MUX_CTL_PAD_D3_VSYNC,Software Multiplexer Control Registers (D3_VSYNC)"
|
|
bitfld.long 0x21c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x21c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_VSYNC:ipu,Reserved,DISPB_CS1:ipu,Reserved,Reserved,GPIO[2]:gpio1,DEBUG_YIELD:sdma,TRACE[19]:arm11p_top"
|
|
line.long 0x220 "SW_MUX_CTL_PAD_D3_REV,Software Multiplexer Control Registers (D3_REV)"
|
|
bitfld.long 0x220 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x220 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_REV:ipu,Reserved,DISPB_SER_RS:ipu,Reserved,Reserved,GPIO[3]:gpio1,DEBUG_BUS_RWB:sdma,TRACE[20]:arm11p_top"
|
|
line.long 0x224 "SW_MUX_CTL_PAD_D3_CLS,Software Multiplexer Control Registers (D3_CLS)"
|
|
bitfld.long 0x224 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x224 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_CLS:ipu,Reserved,DISPB_CS2:ipu,Reserved,Reserved,GPIO[4]:gpio1,DEBUG_BUS_DEVICE[0]:sdma,TRACE[21]:arm11p_top"
|
|
line.long 0x228 "SW_MUX_CTL_PAD_D3_SPL,Software Multiplexer Control Registers (D3_SPL)"
|
|
bitfld.long 0x228 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x228 0.--2. " MUX_MODE ,MUX Mode Select Field" "DISPB_D3_SPL:ipu,Reserved,DISPB_D12_VSYNC:ipu,Reserved,Reserved,GPIO[5]:gpio1,DEBUG_BUS_DEVICE[1]:sdma,TRACE[22]:arm11p_top"
|
|
line.long 0x22c "SW_MUX_CTL_PAD_SD1_CMD,Software Multiplexer Control Registers (SD1_CMD)"
|
|
bitfld.long 0x22c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x22c 0.--2. " MUX_MODE ,MUX Mode Select Field" "CMD:esdhc1,SCLK:mshc,Reserved,DISPB_D0_VSYNC:ipu,USBOTG_DATA[4]:usb_top,GPIO[6]:gpio1,Reserved,TRCTL:arm11p_top"
|
|
line.long 0x230 "SW_MUX_CTL_PAD_SD1_CLK,Software Multiplexer Control Registers (SD1_CLK)"
|
|
bitfld.long 0x230 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x230 0.--2. " MUX_MODE ,MUX Mode Select Field" "CLK:esdhc1,BS:mshc,Reserved,DISPB_BCLK:ipu,USBOTG_DATA[5]:usb_top,GPIO[7]:gpio1,Reserved,TRCLK:arm11p_top"
|
|
line.long 0x234 "SW_MUX_CTL_PAD_SD1_DATA0,Software Multiplexer Control Registers (SD1_DATA0)"
|
|
bitfld.long 0x234 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x234 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT0:esdhc1,DATA[0]:mshc,Reserved,DISPB_CS0:ipu,USBOTG_DATA[6]:usb_top,GPIO[8]:gpio1,Reserved,TRACE[23]:arm11p_top"
|
|
line.long 0x238 "SW_MUX_CTL_PAD_SD1_DATA1,Software Multiplexer Control Registers (SD1_DATA1)"
|
|
bitfld.long 0x238 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x238 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT1:esdhc1,DATA[1]:mshc,Reserved,DISPB_PAR_RS:ipu,USBOTG_DATA[0]:usb_top,GPIO[9]:gpio1,Reserved,TRACE[24]:arm11p_top"
|
|
line.long 0x23c "SW_MUX_CTL_PAD_SD1_DATA2,Software Multiplexer Control Registers (SD1_DATA2)"
|
|
bitfld.long 0x23c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x23c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT2:esdhc1,DATA[2]:mshc,Reserved,DISPB_WR:ipu,USBOTG_DATA[1]:usb_top,GPIO[10]:gpio1,Reserved,TRACE[25]:arm11p_top"
|
|
line.long 0x240 "SW_MUX_CTL_PAD_SD1_DATA3,Software Multiplexer Control Registers (SD1_DATA3)"
|
|
bitfld.long 0x240 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x240 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT3:esdhc1,DATA[3]:mshc,Reserved,DISPB_RD:ipu,USBOTG_DATA[2]:usb_top,GPIO[11]:gpio1,Reserved,TRACE[26]:arm11p_top"
|
|
line.long 0x244 "SW_MUX_CTL_PAD_SD2_CMD,Software Multiplexer Control Registers (SD2_CMD)"
|
|
bitfld.long 0x244 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x244 0.--2. " MUX_MODE ,MUX Mode Select Field" "CMD:esdhc2,SCL:i2c3,DAT4:esdhc1,CSI_D[2]:ipu,USBH2_DATA[4]:usb_top,GPIO[0]:gpio2,SPDIF_OUT1:spdif,DISPB_D12_VSYNC:ipu"
|
|
line.long 0x248 "SW_MUX_CTL_PAD_SD2_CLK,Software Multiplexer Control Registers (SD2_CLK)"
|
|
bitfld.long 0x248 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x248 0.--2. " MUX_MODE ,MUX Mode Select Field" "CLK:esdhc2,SDA:i2c3,DAT5:esdhc1,CSI_D[3]:ipu,USBH2_DATA[5]:usb_top,GPIO[1]:gpio2,SPDIF_IN1:spdif,DISPB_CS2:ipu"
|
|
line.long 0x24c "SW_MUX_CTL_PAD_SD2_DATA0,Software Multiplexer Control Registers (SD2_DATA0)"
|
|
bitfld.long 0x24c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x24c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT0:esdhc2,RXD_MUX:uart3,DAT6:esdhc1,CSI_D[4]:ipu,USBH2_DATA[6]:usb_top,GPIO[2]:gpio2,SPDIF_EXTCLK:spdif,?..."
|
|
line.long 0x250 "SW_MUX_CTL_PAD_SD2_DATA1,Software Multiplexer Control Registers (SD2_DATA1)"
|
|
bitfld.long 0x250 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x250 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT1:esdhc2,TXD_MUX:uart3,DAT7:esdhc1,CSI_D[5]:ipu,USBH2_DATA[0]:usb_top,GPIO[3]:gpio2,?..."
|
|
line.long 0x254 "SW_MUX_CTL_PAD_SD2_DATA2,Software Multiplexer Control Registers (SD2_DATA2)"
|
|
bitfld.long 0x254 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x254 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT2:esdhc2,RTS:uart3,RXCAN:can1,CSI_D[6]:ipu,USBH2_DATA[1]:usb_top,GPIO[4]:gpio2,?..."
|
|
line.long 0x258 "SW_MUX_CTL_PAD_SD2_DATA3,Software Multiplexer Control Registers (SD2_DATA3)"
|
|
bitfld.long 0x258 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x258 0.--2. " MUX_MODE ,MUX Mode Select Field" "DAT3:esdhc2,CTS:uart3,TXCAN:can1,CSI_D[7]:ipu,USBH2_DATA[2]:usb_top,GPIO[5]:gpio2,?..."
|
|
line.long 0x25c "SW_MUX_CTL_PAD_ATA_CS0,Software Multiplexer Control Registers (ATA_CS0)"
|
|
bitfld.long 0x25c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x25c 0.--2. " MUX_MODE ,MUX Mode Select Field" "CS0:ata,SS3:cspi1,Reserved,DISPB_CS1:ipu,Reserved,GPIO[6]:gpio2,DIAGB[0]:ipu,MAX1_HMASTER_0:arm11p_top"
|
|
line.long 0x260 "SW_MUX_CTL_PAD_ATA_CS1,Software Multiplexer Control Registers (ATA_CS1)"
|
|
bitfld.long 0x260 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x260 0.--2. " MUX_MODE ,MUX Mode Select Field" "CS1:ata,Reserved,Reserved,DISPB_CS2:ipu,SS0:cspi2,GPIO[7]:gpio2,DIAGB[1]:ipu,MAX1_HMASTER_1:arm11p_top"
|
|
line.long 0x264 "SW_MUX_CTL_PAD_ATA_DIOR,Software Multiplexer Control Registers (ATA_DIOR)"
|
|
bitfld.long 0x264 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x264 0.--2. " MUX_MODE ,MUX Mode Select Field" "DIOR:ata,DAT0:esdhc3,USBOTG_DIR:usb_top,DISPB_BE0:ipu,SS1:cspi2,GPIO[8]:gpio2,DIAGB[2]:ipu,MAX1_HMASTER_2:arm11p_top"
|
|
line.long 0x268 "SW_MUX_CTL_PAD_ATA_DIOW,Software Multiplexer Control Registers (ATA_DIOW)"
|
|
bitfld.long 0x268 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x268 0.--2. " MUX_MODE ,MUX Mode Select Field" "DIOW:ata,DAT1:esdhc3,USBOTG_STP:usb_top,DISPB_BE1:ipu,MOSI:cspi2,GPIO[9]:gpio2,DIAGB[3]:ipu,MAX1_HMASTER_3:arm11p_top"
|
|
line.long 0x26c "SW_MUX_CTL_PAD_ATA_DMACK,Software Multiplexer Control Registers (ATA_DMACK)"
|
|
bitfld.long 0x26c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x26c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DMACK:ata,DAT2:esdhc3,USBOTG_NXT:usb_top,Reserved,MISO:cspi2,GPIO[10]:gpio2,DIAGB[4]:ipu,MAX0_HMASTER_0:arm11p_top"
|
|
line.long 0x270 "SW_MUX_CTL_PAD_ATA_RESET_B,Software Multiplexer Control Registers (ATA_RESET_B)"
|
|
bitfld.long 0x270 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x270 0.--2. " MUX_MODE ,MUX Mode Select Field" "RESET_B:ata,DAT3:esdhc3,USBOTG_DATA[0]:usb_top,DISPB_SD_D_O:ipu,RDY:cspi2,GPIO[11]:gpio2,DIAGB[5]:ipu,MAX0_HMASTER_1:arm11p_top"
|
|
line.long 0x274 "SW_MUX_CTL_PAD_ATA_IORDY,Software Multiplexer Control Registers (ATA_IORDY)"
|
|
bitfld.long 0x274 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x274 0.--2. " MUX_MODE ,MUX Mode Select Field" "IORDY:ata,DAT4:esdhc3,esdhc3:usb_top,DISPB_SD_D_IO:ipu,DAT4:esdhc2,GPIO[12]:gpio2,DIAGB[6]:ipu,MAX0_HMASTER_2:arm11p_top"
|
|
line.long 0x278 "SW_MUX_CTL_PAD_ATA_DATA0,Software Multiplexer Control Registers (ATA_DATA0)"
|
|
bitfld.long 0x278 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x278 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[0]:ata,DAT5:esdhc3,USBOTG_DATA[2]:usb_top,DISPB_D12_VSYNC:ipu,DAT5:esdhc2,GPIO[13]:gpio2,DIAGB[7]:ipu,MAX0_HMASTER_3:arm11p_top"
|
|
line.long 0x27c "SW_MUX_CTL_PAD_ATA_DATA1,Software Multiplexer Control Registers (ATA_DATA1)"
|
|
bitfld.long 0x27c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x27c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[1]:ata,DAT6:esdhc3,USBOTG_DATA[3]:usb_top,DISPB_SD_CLK:ipu,DAT6:esdhc2,GPIO[14]:gpio2,DIAGB[8]:ipu,TRACE[27]:arm11p_top"
|
|
line.long 0x280 "SW_MUX_CTL_PAD_ATA_DATA2,Software Multiplexer Control Registers (ATA_DATA2)"
|
|
bitfld.long 0x280 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x280 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[2]:ata,DAT7:esdhc3,USBOTG_DATA[4]:usb_top,DISPB_SER_RS:ipu,DAT7:esdhc2,GPIO[15]:gpio2,DIAGB[9]:ipu,TRACE[28]:arm11p_top"
|
|
line.long 0x284 "SW_MUX_CTL_PAD_ATA_DATA3,Software Multiplexer Control Registers (ATA_DATA3)"
|
|
bitfld.long 0x284 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x284 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[3]:ata,CLK:esdhc3,USBOTG_DATA[5]:usb_top,Reserved,SCLK:cspi2,GPIO[16]:gpio2,DIAGB[10]:ipu,TRACE[29]:arm11p_top"
|
|
line.long 0x288 "SW_MUX_CTL_PAD_ATA_DATA4,Software Multiplexer Control Registers (ATA_DATA4)"
|
|
bitfld.long 0x288 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x288 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[4]:ata,CMD:esdhc3,USBOTG_DATA[6]:usb_top,Reserved,Reserved,GPIO[17]:gpio2,DIAGB[11]:ipu,TRACE[30]:arm11p_top"
|
|
line.long 0x28c "SW_MUX_CTL_PAD_ATA_DATA5,Software Multiplexer Control Registers (ATA_DATA5)"
|
|
bitfld.long 0x28c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x28c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[5]:ata,Reserved,USBOTG_DATA[7]:usb_top,Reserved,Reserved,GPIO[18]:gpio2,DIAGB[12]:ipu,TRACE[31]:arm11p_top"
|
|
line.long 0x290 "SW_MUX_CTL_PAD_ATA_DATA6,Software Multiplexer Control Registers (ATA_DATA6)"
|
|
bitfld.long 0x290 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x290 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[6]:ata,TXCAN:can1,DTR:uart1,AUD6_TXD:audmux,Reserved,GPIO[19]:gpio2,DIAGB[13]:ipu,?..."
|
|
line.long 0x294 "SW_MUX_CTL_PAD_ATA_DATA7,Software Multiplexer Control Registers (ATA_DATA7)"
|
|
bitfld.long 0x294 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x294 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[7]:ata,RXCAN:can1,DSR:uart1,AUD6_RXD:audmux,Reserved,GPIO[20]:gpio2,DIAGB[14]:ipu,?..."
|
|
line.long 0x298 "SW_MUX_CTL_PAD_ATA_DATA8,Software Multiplexer Control Registers (ATA_DATA8)"
|
|
bitfld.long 0x298 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x298 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[8]:ata,RTS:uart3,RI:uart1,AUD6_TXC:audmux,Reserved,GPIO[21]:gpio2,DIAGB[15]:ipu,?..."
|
|
line.long 0x29c "SW_MUX_CTL_PAD_ATA_DATA9,Software Multiplexer Control Registers (ATA_DATA9)"
|
|
bitfld.long 0x29c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x29c 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[9]:ata,CTS:uart3,DCD:uart1,AUD6_TXFS:audmux,Reserved,GPIO[22]:gpio2,DIAGB[16]:ipu,?..."
|
|
line.long 0x2a0 "SW_MUX_CTL_PAD_ATA_DATA10,Software Multiplexer Control Registers (ATA_DATA10)"
|
|
bitfld.long 0x2a0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2a0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[10]:ata,RXD_MUX:uart3,Reserved,AUD6_RXC:audmux,Reserved,GPIO[23]:gpio2,DIAGB[17]:ipu,?..."
|
|
line.long 0x2a4 "SW_MUX_CTL_PAD_ATA_DATA11,Software Multiplexer Control Registers (ATA_DATA11)"
|
|
bitfld.long 0x2a4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2a4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[11]:ata,TXD_MUX:uart3,Reserved,AUD6_RXFS:audmux,Reserved,GPIO[24]:gpio2,DIAGB[18]:ipu,?..."
|
|
line.long 0x2a8 "SW_MUX_CTL_PAD_ATA_DATA12,Software Multiplexer Control Registers (ATA_DATA12)"
|
|
bitfld.long 0x2a8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2a8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[12]:ata,SCL:i2c3,Reserved,Reserved,Reserved,GPIO[25]:gpio2,DIAGB[19]:ipu,?..."
|
|
line.long 0x2ac "SW_MUX_CTL_PAD_ATA_DATA13,Software Multiplexer Control Registers (ATA_DATA13)"
|
|
bitfld.long 0x2ac 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2ac 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[13]:ata,SDA:i2c3,Reserved,Reserved,Reserved,GPIO[26]:gpio2,DIAGB[20]:ipu,?..."
|
|
line.long 0x2b0 "SW_MUX_CTL_PAD_ATA_DATA14,Software Multiplexer Control Registers (ATA_DATA14)"
|
|
bitfld.long 0x2b0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2b0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[14]:ata,CSI_D[0]:ipu,Reserved,ROW[0]:kpp,Reserved,GPIO[27]:gpio2,DIAGB[21]:ipu,?..."
|
|
line.long 0x2b4 "SW_MUX_CTL_PAD_ATA_DATA15,Software Multiplexer Control Registers (ATA_DATA15)"
|
|
bitfld.long 0x2b4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2b4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DATA[15]:ata,CSI_D[1]:ipu,Reserved,ROW[1]:kpp,Reserved,GPIO[28]:gpio2,DIAGB[22]:ipu,?..."
|
|
line.long 0x2b8 "SW_MUX_CTL_PAD_ATA_INTRQ,Software Multiplexer Control Registers (ATA_INTRQ)"
|
|
bitfld.long 0x2b8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2b8 0.--2. " MUX_MODE ,MUX Mode Select Field" "INTRQ:ata,CSI_D[2]:ipu,Reserved,ROW[2]:kpp,Reserved,GPIO[29]:gpio2,DIAGB[23]:ipu,?..."
|
|
line.long 0x2bc "SW_MUX_CTL_PAD_ATA_BUFF_EN,Software Multiplexer Control Registers (ATA_BUFF_EN)"
|
|
bitfld.long 0x2bc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2bc 0.--2. " MUX_MODE ,MUX Mode Select Field" "BUFFER_EN:ata,CSI_D[3]:ipu,Reserved,ROW[3]:kpp,Reserved,GPIO[30]:gpio2,DIAGB[24]:ipu,?..."
|
|
line.long 0x2c0 "SW_MUX_CTL_PAD_ATA_DMARQ,Software Multiplexer Control Registers (ATA_DMARQ)"
|
|
bitfld.long 0x2c0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2c0 0.--2. " MUX_MODE ,MUX Mode Select Field" "DMARQ:ata,CSI_D[4]:ipu,Reserved,COL[0]:kpp,Reserved,GPIO[31]:gpio2,DIAGB[25]:ipu,CTI_TRIG_IN1_4:ect"
|
|
line.long 0x2c4 "SW_MUX_CTL_PAD_ATA_DA0,Software Multiplexer Control Registers (ATA_DA0)"
|
|
bitfld.long 0x2c4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2c4 0.--2. " MUX_MODE ,MUX Mode Select Field" "DA_0:ata,CSI_D[5]:ipu,Reserved,COL[1]:kpp,Reserved,GPIO[0]:gpio3,DIAGB[26]:ipu,CTI_TRIG_IN1_5:ect"
|
|
line.long 0x2c8 "SW_MUX_CTL_PAD_ATA_DA1,Software Multiplexer Control Registers (ATA_DA1)"
|
|
bitfld.long 0x2c8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2c8 0.--2. " MUX_MODE ,MUX Mode Select Field" "DA_1:ata,CSI_D[6]:ipu,Reserved,COL[2]:kpp,Reserved,GPIO[1]:gpio3,DIAGB[27]:ipu,CTI_TRIG_IN1_6:ect"
|
|
line.long 0x2cc "SW_MUX_CTL_PAD_ATA_DA2,Software Multiplexer Control Registers (ATA_DA2)"
|
|
bitfld.long 0x2cc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2cc 0.--2. " MUX_MODE ,MUX Mode Select Field" "DA_2:ata,CSI_D[7]:ipu,Reserved,COL[3]:kpp,Reserved,GPIO[2]:gpio3,DIAGB[28]:ipu,CTI_TRIG_IN1_7:ect"
|
|
line.long 0x2d0 "SW_MUX_CTL_PAD_MLB_CLK,Software Multiplexer Control Registers (MLB_CLK)"
|
|
bitfld.long 0x2d0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2d0 0.--2. " MUX_MODE ,MUX Mode Select Field" "MLBCLK:mlb,Reserved,Reserved,Reserved,Reserved,GPIO[3]:gpio3,?..."
|
|
line.long 0x2d4 "SW_MUX_CTL_PAD_MLB_DAT,Software Multiplexer Control Registers (MLB_DAT)"
|
|
bitfld.long 0x2d4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2d4 0.--2. " MUX_MODE ,MUX Mode Select Field" "MLBDAT,Reserved,Reserved,Reserved,Reserved,GPIO[4]:gpio3,?..."
|
|
line.long 0x2d8 "SW_MUX_CTL_PAD_MLB_SIG,Software Multiplexer Control Registers (MLB_SIG)"
|
|
bitfld.long 0x2d8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2d8 0.--2. " MUX_MODE ,MUX Mode Select Field" "MLBSIG:mlb,Reserved,Reserved,Reserved,Reserved,GPIO[5]:gpio3,?..."
|
|
line.long 0x2dc "SW_MUX_CTL_PAD_FEC_TX_CLK,Software Multiplexer Control Registers (FEC_TX_CLK)"
|
|
bitfld.long 0x2dc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2dc 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX_CLK:fec,DAT4:esdhc1,RXD_MUX:uart3,USBH2_DIR:usb_top,MOSI:cspi2,GPIO[6]:gpio3,DISPB_D12_VSYNC:ipu,EVNTBUS[0]:arm11p_top"
|
|
line.long 0x2e0 "SW_MUX_CTL_PAD_RX_CLK,Software Multiplexer Control Registers (RX_CLK)"
|
|
bitfld.long 0x2e0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2e0 0.--2. " MUX_MODE ,MUX Mode Select Field" "RX_CLK:fec,DAT5:esdhc1,TXD_MUX:uart3,USBH2_STP:usb_top,MISO:cspi2,GPIO[7]:gpio3,DISPB_SD_D_I:ipu,EVNTBUS[1]:arm11p_top"
|
|
line.long 0x2e4 "SW_MUX_CTL_PAD_FEC_RX_DV,Software Multiplexer Control Registers (FEC_RX_DV)"
|
|
bitfld.long 0x2e4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2e4 0.--2. " MUX_MODE ,MUX Mode Select Field" "RX_DV:fec,DAT6:esdhc1,RTS:uart3,USBH2_NXT:usb_top,SCLK:cspi2,GPIO[8]:gpio3,DISPB_SD_CLK:ipu,EVNTBUS[2]:arm11p_top"
|
|
line.long 0x2e8 "SW_MUX_CTL_PAD_FEC_COL,Software Multiplexer Control Registers (FEC_COL)"
|
|
bitfld.long 0x2e8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2e8 0.--2. " MUX_MODE ,MUX Mode Select Field" "COL:fec,DAT7:esdhc1,CTS:uart3,USBH2_DATA[0]:usb_top,RDY:cspi2,GPIO[9]:gpio3,DISPB_SER_RS:ipu,EVNTBUS[3]:arm11p_top"
|
|
line.long 0x2ec "SW_MUX_CTL_PAD_FEC_RDATA0,Software Multiplexer Control Registers (FEC_RDATA0)"
|
|
bitfld.long 0x2ec 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2ec 0.--2. " MUX_MODE ,MUX Mode Select Field" "RDATA[0]:fec,PWMO:pwm,DTR:uart3,USBH2_DATA[1]:usb_top,SS0:cspi2,GPIO[10]:gpio3,DISPB_CS1:ipu,EVNTBUS[4]:arm11p_top"
|
|
line.long 0x2f0 "SW_MUX_CTL_PAD_FEC_TDATA0,Software Multiplexer Control Registers (FEC_TDATA0)"
|
|
bitfld.long 0x2f0 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2f0 0.--2. " MUX_MODE ,MUX Mode Select Field" "TDATA[0]:fec,SPDIF_OUT1:spdif,DSR:uart3,USBH2_DATA[2]:usb_top,SS1:cspi2,GPIO[11]:gpio3,DISPB_CS0:ipu,EVNTBUS[5]:arm11p_top"
|
|
line.long 0x2f4 "SW_MUX_CTL_PAD_FEC_TX_EN,Software Multiplexer Control Registers (FEC_TX_EN)"
|
|
bitfld.long 0x2f4 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2f4 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX_EN:fec,SPDIF_IN1:spdif,RI:uart3,USBH2_DATA[3]:usb_top,Reserved,GPIO[12]:gpio3,DISPB_PAR_RS:ipu,EVNTBUS[6]:arm11p_top"
|
|
line.long 0x2f8 "SW_MUX_CTL_PAD_FEC_MDC,Software Multiplexer Control Registers (FEC_MDC)"
|
|
bitfld.long 0x2f8 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2f8 0.--2. " MUX_MODE ,MUX Mode Select Field" "MDC:fec,TXCAN:can2,DCD:uart3,USBH2_DATA[4]:usb_top,Reserved,GPIO[13]:gpio3,DISPB_WR:ipu,EVNTBUS[7]:arm11p_top"
|
|
line.long 0x2fc "SW_MUX_CTL_PAD_FEC_MDIO,Software Multiplexer Control Registers (FEC_MDIO)"
|
|
bitfld.long 0x2fc 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x2fc 0.--2. " MUX_MODE ,MUX Mode Select Field" "MDIO:fec,RXCAN:can2,Reserved,USBH2_DATA[5]:usb_top,Reserved,GPIO[14]:gpio3,DISPB_RD:ipu,EVNTBUS[8]:arm11p_top"
|
|
line.long 0x300 "SW_MUX_CTL_PAD_FEC_TX_ERR,Software Multiplexer Control Registers (FEC_TX_ERR)"
|
|
bitfld.long 0x300 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x300 0.--2. " MUX_MODE ,MUX Mode Select Field" "TX_ERR:fec,LINE:owire,SPDIF_EXTCLK:spdif,USBH2_DATA[6]:usb_top,Reserved,GPIO[15]:gpio3,DISPB_D0_VSYNC:ipu,EVNTBUS[9]:arm11p_top"
|
|
line.long 0x304 "SW_MUX_CTL_PAD_FEC_RX_ERR,Software Multiplexer Control Registers (FEC_RX_ERR)"
|
|
bitfld.long 0x304 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x304 0.--2. " MUX_MODE ,MUX Mode Select Field" "RX_ERR:fec,CSI_D[0]:ipu,Reserved,USBH2_DATA[7]:usb_top,COL[4]:kpp,GPIO[16]:gpio3,DISPB_SD_D_IO:ipu,?..."
|
|
line.long 0x308 "SW_MUX_CTL_PAD_FEC_CRS,Software Multiplexer Control Registers (FEC_CRS)"
|
|
bitfld.long 0x308 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x308 0.--2. " MUX_MODE ,MUX Mode Select Field" "CRS:fec,CSI_D[1]:ipu,Reserved,USBH2_PWR:usb_top,COL[5]:kpp,GPIO[17]:gpio3,FLASH_STROBE:ipu,?..."
|
|
line.long 0x30c "SW_MUX_CTL_PAD_FEC_RDATA1,Software Multiplexer Control Registers (FEC_RDATA1)"
|
|
bitfld.long 0x30c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x30c 0.--2. " MUX_MODE ,MUX Mode Select Field" "RDATA[1]:fec,CSI_D[2]:ipu,AUD6_RXC:audmux,USBH2_OC:usb_top,COL[6]:kpp,GPIO[18]:gpio3,DISPB_BE0:ipu,?..."
|
|
line.long 0x310 "SW_MUX_CTL_PAD_FEC_TDATA1,Software Multiplexer Control Registers (FEC_TDATA1)"
|
|
bitfld.long 0x310 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x310 0.--2. " MUX_MODE ,MUX Mode Select Field" "TDATA[1]:fec,CSI_D[3]:ipu,AUD6_RXFS:audmux,Reserved,COL[7]:kpp,GPIO[19]:gpio3,DISPB_BE1:ipu,?..."
|
|
line.long 0x314 "SW_MUX_CTL_PAD_FEC_RDATA2,Software Multiplexer Control Registers (FEC_RDATA2)"
|
|
bitfld.long 0x314 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x314 0.--2. " MUX_MODE ,MUX Mode Select Field" "RDATA[2]:fec,CSI_D[4]:ipu,AUD6_TXD:audmux,Reserved,ROW[4]:kpp,GPIO[20]:gpio3,?..."
|
|
line.long 0x318 "SW_MUX_CTL_PAD_FEC_TDATA2,Software Multiplexer Control Registers (FEC_TDATA2)"
|
|
bitfld.long 0x318 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x318 0.--2. " MUX_MODE ,MUX Mode Select Field" "TDATA[2]:fec,CSI_D[5]:ipu,AUD6_RXD:audmux,Reserved,ROW[5]:kpp,GPIO[21]:gpio3,?..."
|
|
line.long 0x31c "SW_MUX_CTL_PAD_FEC_RDATA3,Software Multiplexer Control Registers (FEC_RDATA3)"
|
|
bitfld.long 0x31c 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x31c 0.--2. " MUX_MODE ,MUX Mode Select Field" "RDATA[3]:fec,CSI_D[6]:ipu,AUD6_TXC:audmux,Reserved,ROW[6]:kpp,GPIO[22]:gpio3,?..."
|
|
line.long 0x320 "SW_MUX_CTL_PAD_FEC_TDATA3,Software Multiplexer Control Registers (FEC_TDATA3)"
|
|
bitfld.long 0x320 4. " SION ,Software Input On Field" "Normal,Loopback"
|
|
textline " "
|
|
bitfld.long 0x320 0.--2. " MUX_MODE ,MUX Mode Select Field" "TDATA[3]:fec,CSI_D[7]:ipu,AUD6_TXFS:audmux,Reserved,ROW[7]:kpp,GPIO[23]:gpio3,?..."
|
|
tree.end
|
|
width 42.
|
|
tree "SW_SELECT_INPUT Registers"
|
|
group.long 0x7a8++0x24f
|
|
line.long 0x00 "AUDMUX_P5_INPUT_RXCLK_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P5_INPUT_RXCLK_AMX)"
|
|
bitfld.long 0x00 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "HCKT:ALT1,RTS2: ALT6"
|
|
line.long 0x04 "AUDMUX_P5_INPUT_RXFS_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P5_INPUT_RXFS_AMX)"
|
|
bitfld.long 0x04 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "HCKR:ALT1,CTS2:ALT6"
|
|
line.long 0x08 "AUDMUX_P6_INPUT_DA_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_DA_AMX)"
|
|
bitfld.long 0x08 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA7:ALT3,FEC_TDATA2:ALT2"
|
|
line.long 0x0c "AUDMUX_P6_INPUT_DB_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_DB_AMX)"
|
|
bitfld.long 0x0c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA6:ALT3,FEC_RDATA2:ALT2"
|
|
line.long 0x10 "AUDMUX_P6_INPUT_RXCLK_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_RXCLK_AMX)"
|
|
bitfld.long 0x10 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA10:ALT3,FEC_RDATA1:ALT2"
|
|
line.long 0x14 "AUDMUX_P6_INPUT_RXFS_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_RXFS_AMX)"
|
|
bitfld.long 0x14 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA11:ALT3,FEC_TDATA1:ALT2"
|
|
line.long 0x18 "AUDMUX_P6_INPUT_TXCLK_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_TXCLK_AMX)"
|
|
bitfld.long 0x18 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA8:ALT3,FEC_RDATA3:ALT2"
|
|
line.long 0x1c "AUDMUX_P6_INPUT_TXFS_AMX_SELECT_INPUT,Software Select Input Control Registers (AUDMUX_P6_INPUT_TXFS_AMX)"
|
|
bitfld.long 0x1c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "ATA_DATA9:ALT3,FEC_TDATA3:ALT2"
|
|
line.long 0x20 "CAN1_IPP_IND_CANRX_SELECT_INPUT,Software Select Input Control Registers (CAN1_IPP_IND_CANRX)"
|
|
bitfld.long 0x20 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C2_DAT:ALT1,SD2_DATA2:ALT2,ATA_DATA7:ALT1,?..."
|
|
line.long 0x24 "CAN2_IPP_IND_CANRX_SELECT_INPUT,Software Select Input Control Registers (CAN2_IPP_IND_CANRX)"
|
|
bitfld.long 0x24 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX4_RX1:ALT3,RTS2:ALT2,FEC_MDIO:ALT1,?..."
|
|
line.long 0x28 "CCM_IPP_32K_MUXED_IN_SELECT_INPUT,Software Select Input Control Registers (CCM_IPP_32K_MUXED_IN)"
|
|
bitfld.long 0x28 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CAPTURE:ALT4,CSPI1_SS1:ALT2"
|
|
line.long 0x2c "CCM_IPP_PMIC_RDY_SELECT_INPUT,Software Select Input Control Registers (CCM_IPP_PMIC_RDY)"
|
|
bitfld.long 0x2c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO1_0:ALT1,TX1:ALT1"
|
|
line.long 0x30 "CSPI1_IPP_IND_SS2_B_SELECT_INPUT,Software Select Input Control Registers (CSPI1_IPP_IND_SS2_B)"
|
|
bitfld.long 0x30 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO1_1:ALT3,CS5:ALT2,TX1:ALT2,?..."
|
|
line.long 0x34 "CSPI1_IPP_IND_SS3_B_SELECT_INPUT,Software Select Input Control Registers (CSPI1_IPP_IND_SS3_B)"
|
|
bitfld.long 0x34 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX0:ALT2,ATA_CS0:ALT1"
|
|
line.long 0x38 "CSPI2_IPP_CSPI_CLK_IN_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_CSPI_CLK_IN)"
|
|
bitfld.long 0x38 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "SCK5:ALT2,RTS1:ALT1,ATA_DATA3:ALT4,FEC_RX_DV:ALT4"
|
|
line.long 0x3c "CSPI2_IPP_IND_DATAREADY_B_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_DATAREADY_B)"
|
|
bitfld.long 0x3c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "STXFS5:ALT2,CTS1:ALT1,ATA_RESET_B:ALT4,FEC_COL:ALT4"
|
|
line.long 0x40 "CSPI2_IPP_IND_MISO_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_MISO)"
|
|
bitfld.long 0x40 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "SRXD5:ALT2,TXD1:ALT1,ATA_DMACK:ALT4,FEC_RX_CLK:ALT4"
|
|
line.long 0x44 "CSPI2_IPP_IND_MOSI_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_MOSI)"
|
|
bitfld.long 0x44 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "STXD5:ALT2,RXD1:ALT1,ATA_DIOW:ALT4,FEC_TX_CLK:ALT4"
|
|
line.long 0x48 "CSPI2_IPP_IND_SS0_B_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_SS0_B)"
|
|
bitfld.long 0x48 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "HCKR:ALT2,ATA_CS1:ALT4,FEC_RDATA0:ALT4,?..."
|
|
line.long 0x4c "CSPI2_IPP_IND_SS1_B_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_SS1_B)"
|
|
bitfld.long 0x4c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CAPTURE:ALT2,ATA_DIOR:ALT4,FEC_TDATA0:ALT4,?..."
|
|
line.long 0x50 "CSPI2_IPP_IND_SS2_B_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_SS2_B)"
|
|
bitfld.long 0x50 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CS5:ALT1,TX5_RX0:ALT2"
|
|
line.long 0x54 "CSPI2_IPP_IND_SS3_B_SELECT_INPUT,Software Select Input Control Registers (CSPI2_IPP_IND_SS3_B)"
|
|
bitfld.long 0x54 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX4_RX1:ALT2,CSPI1_SS0:ALT2"
|
|
line.long 0x58 "EMI_IPP_IND_WEIM_DTACK_B_SELECT_INPUT,Software Select Input Control Registers (EMI_IPP_IND_WEIM_DTACK_B)"
|
|
bitfld.long 0x58 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CS4:ALT1,TX0:ALT3"
|
|
line.long 0x5c "ESDHC1_IPP_DAT4_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC1_IPP_DAT4_IN)"
|
|
bitfld.long 0x5c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_CMD:ALT2,FEC_TX_CLK:ALT1"
|
|
line.long 0x60 "ESDHC1_IPP_DAT5_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC1_IPP_DAT5_IN)"
|
|
bitfld.long 0x60 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_CLK:ALT2,FEC_RX_CLK:ALT1"
|
|
line.long 0x64 "ESDHC1_IPP_DAT6_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC1_IPP_DAT6_IN)"
|
|
bitfld.long 0x64 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA0:ALT2,FEC_RX_DV:ALT1"
|
|
line.long 0x68 "ESDHC1_IPP_DAT7_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC1_IPP_DAT7_IN)"
|
|
bitfld.long 0x68 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA1:ALT2,FEC_COL:ALT1"
|
|
line.long 0x6c "ESDHC3_IPP_CARD_CLK_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_CARD_CLK_IN)"
|
|
bitfld.long 0x6c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD19:ALT3,ATA_DATA3:ALT1"
|
|
line.long 0x70 "ESDHC3_IPP_CMD_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_CMD_IN)"
|
|
bitfld.long 0x70 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD18:ALT3,ATA_DATA4:ALT1"
|
|
line.long 0x74 "ESDHC3_IPP_DAT0_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_DAT0_IN)"
|
|
bitfld.long 0x74 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD20:ALT3,ATA_DIOR:ALT1"
|
|
line.long 0x78 "ESDHC3_IPP_DAT1_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_DAT1)"
|
|
bitfld.long 0x78 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD21:ALT3,ATA_DIOW:ALT1"
|
|
line.long 0x7c "ESDHC3_IPP_DAT2_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_DAT2)"
|
|
bitfld.long 0x7c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD22:ALT3,ATA_DMACK:ALT1"
|
|
line.long 0x80 "ESDHC3_IPP_DAT3_IN_SELECT_INPUT,Software Select Input Control Registers (ESDHC3_IPP_DAT3_IN)"
|
|
bitfld.long 0x80 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD23:ALT3,ATA_RESET_B:ALT1"
|
|
line.long 0x84 "GPIO1_IPP_IND_G_IN_0_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_0)"
|
|
bitfld.long 0x84 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO1_0:ALT0,STXD5:ALT5,D3_DRDY:ALT5,?..."
|
|
line.long 0x88 "GPIO1_IPP_IND_G_IN_10_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_10)"
|
|
bitfld.long 0x88 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX5_RX0:ALT5,SD1_DATA2:ALT5"
|
|
line.long 0x8c "GPIO1_IPP_IND_G_IN_11_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_11)"
|
|
bitfld.long 0x8c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX4_RX1:ALT5,SD1_DATA3:ALT5"
|
|
line.long 0x90 "GPIO1_IPP_IND_G_IN_1_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_1)"
|
|
bitfld.long 0x90 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO1_1:ALT0,SRXD5:ALT5,CONTRAST:ALT5,?..."
|
|
line.long 0x94 "GPIO1_IPP_IND_G_IN_20_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_20)"
|
|
bitfld.long 0x94 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CS4:ALT5,CSI_D8:ALT5"
|
|
line.long 0x98 "GPIO1_IPP_IND_G_IN_21_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_21)"
|
|
bitfld.long 0x98 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CS5:ALT5,CSI_D9:ALT5"
|
|
line.long 0x9c "GPIO1_IPP_IND_G_IN_22_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_22)"
|
|
bitfld.long 0x9c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NF_CE0:ALT5,CSI_D10:ALT5"
|
|
line.long 0xa0 "GPIO1_IPP_IND_G_IN_2_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_2)"
|
|
bitfld.long 0xa0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SCK5:ALT5,D3_VSYNC:ALT5"
|
|
line.long 0xa4 "GPIO1_IPP_IND_G_IN_3_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_3)"
|
|
bitfld.long 0xa4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "STXFS5:ALT5,D3_REV:ALT5"
|
|
line.long 0xa8 "GPIO1_IPP_IND_G_IN_4_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_4)"
|
|
bitfld.long 0xa8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CAPTURE:ALT5,SCKR:ALT5,D3_CLS:ALT5,?..."
|
|
line.long 0xac "GPIO1_IPP_IND_G_IN_5_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_5)"
|
|
bitfld.long 0xac 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "COMPARE:ALT5,FSR:ALT5,D3_SPL:ALT5,?..."
|
|
line.long 0xb0 "GPIO1_IPP_IND_G_IN_6_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_6)"
|
|
bitfld.long 0xb0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "WDOG_RST:ALT5,HCKR:ALT5,SD1_CMD:ALT5,?..."
|
|
line.long 0xb4 "GPIO1_IPP_IND_G_IN_7_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_7)"
|
|
bitfld.long 0xb4 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "VSTBY:ALT5,SCKT:ALT5,SD1_CLK:ALT5,?..."
|
|
line.long 0xb8 "GPIO1_IPP_IND_G_IN_8_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_8)"
|
|
bitfld.long 0xb8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CLKO:ALT5,FST:ALT5,SD1_DATA0:ALT5,?..."
|
|
line.long 0xbc "GPIO1_IPP_IND_G_IN_9_SELECT_INPUT,Software Select Input Control Registers (GPIO1_IPP_IND_G_IN_9)"
|
|
bitfld.long 0xbc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "HCKT:ALT5,SD1_DATA1:ALT5"
|
|
line.long 0xc0 "GPIO2_IPP_IND_G_IN_0_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_0)"
|
|
bitfld.long 0xc0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO2_0:ALT0,LD0:ALT5,SD2_CMD:ALT5,?..."
|
|
line.long 0xc4 "GPIO2_IPP_IND_G_IN_10_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_10)"
|
|
bitfld.long 0xc4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD10:ALT5,ATA_DMACK:ALT5"
|
|
line.long 0xc8 "GPIO2_IPP_IND_G_IN_11_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_11)"
|
|
bitfld.long 0xc8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD11:ALT5,ATA_RESET_B:ALT5"
|
|
line.long 0xcc "GPIO2_IPP_IND_G_IN_12_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_12)"
|
|
bitfld.long 0xcc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD12:ALT5,ATA_IORDY:ALT5"
|
|
line.long 0xd0 "GPIO2_IPP_IND_G_IN_13_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_13)"
|
|
bitfld.long 0xd0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD13:ALT5,ATA_DATA0:ALT5"
|
|
line.long 0xd4 "GPIO2_IPP_IND_G_IN_14_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_14)"
|
|
bitfld.long 0xd4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD14:ALT5,ATA_DATA1:ALT5"
|
|
line.long 0xd8 "GPIO2_IPP_IND_G_IN_15_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_15)"
|
|
bitfld.long 0xd8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD15:ALT5,ATA_DATA2:ALT5"
|
|
line.long 0xdc "GPIO2_IPP_IND_G_IN_16_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_16)"
|
|
bitfld.long 0xdc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD16:ALT5,ATA_DATA3:ALT5"
|
|
line.long 0xe0 "GPIO2_IPP_IND_G_IN_17_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_17)"
|
|
bitfld.long 0xe0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD17:ALT5,ATA_DATA4:ALT5"
|
|
line.long 0xe4 "GPIO2_IPP_IND_G_IN_18_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_18)"
|
|
bitfld.long 0xe4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFWE_B:ALT5,ATA_DATA5:ALT5"
|
|
line.long 0xe8 "GPIO2_IPP_IND_G_IN_19_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_19)"
|
|
bitfld.long 0xe8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFRE_B:ALT5,ATA_DATA6:ALT5"
|
|
line.long 0xec "GPIO2_IPP_IND_G_IN_1_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_1)"
|
|
bitfld.long 0xec 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD1:ALT5,SD2_CLK:ALT5"
|
|
line.long 0xf0 "GPIO2_IPP_IND_G_IN_20_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_20)"
|
|
bitfld.long 0xf0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFALE:ALT5,ATA_DATA7:ALT5"
|
|
line.long 0xf4 "GPIO2_IPP_IND_G_IN_21_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_21)"
|
|
bitfld.long 0xf4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFCLE:ALT5,ATA_DATA8:ALT5"
|
|
line.long 0xf8 "GPIO2_IPP_IND_G_IN_22_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_22)"
|
|
bitfld.long 0xf8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFWP_B:ALT5,ATA_DATA9:ALT5"
|
|
line.long 0xfc "GPIO2_IPP_IND_G_IN_23_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_23)"
|
|
bitfld.long 0xfc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFRB:ALT5,ATA_DATA10:ALT5"
|
|
line.long 0x100 "GPIO2_IPP_IND_G_IN_24_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_24)"
|
|
bitfld.long 0x100 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C1_CLK:ALT5,ATA_DATA11:ALT5"
|
|
line.long 0x104 "GPIO2_IPP_IND_G_IN_25_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_25)"
|
|
bitfld.long 0x104 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C1_DAT:ALT5,ATA_DATA12:ALT5"
|
|
line.long 0x108 "GPIO2_IPP_IND_G_IN_26_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_26)"
|
|
bitfld.long 0x108 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C2_CLK:ALT5,ATA_DATA13:ALT5"
|
|
line.long 0x10c "GPIO2_IPP_IND_G_IN_27_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_27)"
|
|
bitfld.long 0x10c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C2_DAT:ALT5,ATA_DATA14:ALT5"
|
|
line.long 0x110 "GPIO2_IPP_IND_G_IN_28_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_28)"
|
|
bitfld.long 0x110 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "STXD4:ALT5,ATA_DATA15:ALT5"
|
|
line.long 0x114 "GPIO2_IPP_IND_G_IN_29_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_29)"
|
|
bitfld.long 0x114 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SRXD4:ALT5,ATA_INTRQ:ALT5"
|
|
line.long 0x118 "GPIO2_IPP_IND_G_IN_2_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_2)"
|
|
bitfld.long 0x118 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD2:ALT5,SD2_DATA0:ALT5"
|
|
line.long 0x11c "GPIO2_IPP_IND_G_IN_30_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_30)"
|
|
bitfld.long 0x11c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SCK4:ALT5,ATA_BUFF_EN:ALT5"
|
|
line.long 0x120 "GPIO2_IPP_IND_G_IN_31_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_31)"
|
|
bitfld.long 0x120 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "STXFS4:ALT5,ATA_DMARQ:ALT5"
|
|
line.long 0x124 "GPIO2_IPP_IND_G_IN_3_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_3)"
|
|
bitfld.long 0x124 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD3:ALT5,SD2_DATA1:ALT5"
|
|
line.long 0x128 "GPIO2_IPP_IND_G_IN_4_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_4)"
|
|
bitfld.long 0x128 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD4:ALT5,SD2_DATA2:ALT5"
|
|
line.long 0x12c "GPIO2_IPP_IND_G_IN_5_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_5)"
|
|
bitfld.long 0x12c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD5:ALT5,SD2_DATA3:ALT5"
|
|
line.long 0x130 "GPIO2_IPP_IND_G_IN_6_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_6)"
|
|
bitfld.long 0x130 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD6:ALT5,ATA_CS0:ALT5"
|
|
line.long 0x134 "GPIO2_IPP_IND_G_IN_7_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_7)"
|
|
bitfld.long 0x134 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD7:ALT5,ATA_CS1:ALT5"
|
|
line.long 0x138 "GPIO2_IPP_IND_G_IN_8_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_8)"
|
|
bitfld.long 0x138 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD8:ALT5,ATA_DIOR:ALT5"
|
|
line.long 0x13c "GPIO2_IPP_IND_G_IN_9_SELECT_INPUT,Software Select Input Control Registers (GPIO2_IPP_IND_G_IN_9)"
|
|
bitfld.long 0x13c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD9:ALT5,ATA_DIOW:ALT5"
|
|
line.long 0x140 "GPIO3_IPP_IND_G_IN_0_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_0)"
|
|
bitfld.long 0x140 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO3_0:ALT0,ATA_DA0:ALT5"
|
|
line.long 0x144 "GPIO3_IPP_IND_G_IN_10_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_10)"
|
|
bitfld.long 0x144 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RXD2:ALT5,FEC_RDATA0:ALT5"
|
|
line.long 0x148 "GPIO3_IPP_IND_G_IN_11_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_11)"
|
|
bitfld.long 0x148 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TXD2:ALT5,FEC_TDATA0:ALT5"
|
|
line.long 0x14c "GPIO3_IPP_IND_G_IN_12_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_12)"
|
|
bitfld.long 0x14c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RTS2:ALT5,FEC_TX_EN:ALT5"
|
|
line.long 0x150 "GPIO3_IPP_IND_G_IN_13_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_13)"
|
|
bitfld.long 0x150 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CTS2:ALT5,FEC_MDC:ALT5"
|
|
line.long 0x154 "GPIO3_IPP_IND_G_IN_14_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_14)"
|
|
bitfld.long 0x154 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "USBOTG_PWR:ALT5,FEC_MDIO:ALT5"
|
|
line.long 0x158 "GPIO3_IPP_IND_G_IN_15_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_15)"
|
|
bitfld.long 0x158 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "USBOTG_OC:ALT5,FEC_TX_ERR:ALT5"
|
|
line.long 0x15c "GPIO3_IPP_IND_G_IN_4_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_4)"
|
|
bitfld.long 0x15c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSPI1_SCLK:ALT5,MLB_DAT:ALT5"
|
|
line.long 0x160 "GPIO3_IPP_IND_G_IN_5_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_5)"
|
|
bitfld.long 0x160 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSPI1_SPI_RDY:ALT5,MLB_SIG:ALT5"
|
|
line.long 0x164 "GPIO3_IPP_IND_G_IN_6_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_6)"
|
|
bitfld.long 0x164 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RXD1:ALT5,FEC_TX_CLK:ALT5"
|
|
line.long 0x168 "GPIO3_IPP_IND_G_IN_7_SELECT_INPUT,Software Select Input Control Registers (_GPIO3_IPP_IND_G_IN_7)"
|
|
bitfld.long 0x168 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TXD1:ALT5,FEC_RX_CLK:ALT5"
|
|
line.long 0x16c "GPIO3_IPP_IND_G_IN_8_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_8)"
|
|
bitfld.long 0x16c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RTS1:ALT5,FEC_RX_DV:ALT5"
|
|
line.long 0x170 "GPIO3_IPP_IND_G_IN_9_SELECT_INPUT,Software Select Input Control Registers (GPIO3_IPP_IND_G_IN_9)"
|
|
bitfld.long 0x170 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CTS1:ALT5,FEC_COL:ALT5"
|
|
line.long 0x174 "I2C3_IPP_SCL_IN_SELECT_INPUT,Software Select Input Control Registers (I2C3_IPP_SCL_IN)"
|
|
bitfld.long 0x174 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX3_RX2:ALT1,RTS1:ALT2,SD2_CMD:ALT1,ATA_DATA12:ALT1"
|
|
line.long 0x178 "I2C3_IPP_SDA_IN_SELECT_INPUT,Software Select Input Control Registers (I2C3_IPP_SDA_IN)"
|
|
bitfld.long 0x178 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX2_RX3:ALT1,CTS1:ALT2,SD2_CLK:ALT1,ATA_DATA13:ALT1"
|
|
line.long 0x17c "IPU_IPP_IND_DISPB_D0_VSYNC_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_DISPB_D0_VSYNC)"
|
|
bitfld.long 0x17c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFWE_B:ALT2,LD18:ALT1,SD1_CMD:ALT3,FEC_TX_ERR:ALT6"
|
|
line.long 0x180 "IPU_IPP_IND_DISPB_D12_VSYNC_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_DISPB_D12_VSYNC)"
|
|
bitfld.long 0x180 0.--2. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD16:ALT2,LD18:ALT2,D3_SPL:ALT2,SD2_CMD:ALT7,ATA_DATA0:ALT3,FEC_TX_CLK:ALT6,?..."
|
|
line.long 0x184 "IPU_IPP_IND_DISPB_SD_D_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_DISPB_SD_D)"
|
|
bitfld.long 0x184 0.--2. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD22:ALT2,LD23:ALT2,D3_HSYNC:ALT2,ATA_IORDY:ALT3,FEC_RX_CLK:ALT6,FEC_RX_ERR:ALT6,?..."
|
|
line.long 0x188 "IPU_IPP_IND_SENSB_DATA_0_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_0)"
|
|
bitfld.long 0x188 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "SCKT:ALT6,RTS1:ALT3,ATA_DATA14:ALT1,FEC_RX_ERR:ALT1"
|
|
line.long 0x18c "IPU_IPP_IND_SENSB_DATA_1_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_1)"
|
|
bitfld.long 0x18c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "FST:ALT6,CTS1:ALT3,ATA_DATA15:ALT1,FEC_CRS:ALT1"
|
|
line.long 0x190 "IPU_IPP_IND_SENSB_DATA_2_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_2)"
|
|
bitfld.long 0x190 0.--2. " DAISY ,Selecting Pads Involved in Daisy Chain" "HCKT:ALT6,RTS2:ALT3,SD2_CMD:ALT3,ATA_INTRQ:ALT1,FEC_RDATA1:ALT1,?..."
|
|
line.long 0x194 "IPU_IPP_IND_SENSB_DATA_3_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_3)"
|
|
bitfld.long 0x194 0.--2. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX4_RX1:ALT6,CTS2:ALT3,SD2_CLK:ALT3,ATA_BUFF_EN:ALT1,FEC_TDATA1:ALT1,?..."
|
|
line.long 0x198 "IPU_IPP_IND_SENSB_DATA_4_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_4)"
|
|
bitfld.long 0x198 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX3_RX2:ALT6,SD2_DATA0:ALT3,ATA_DMARQ:ALT1,FEC_RDATA2:ALT1"
|
|
line.long 0x19c "IPU_IPP_IND_SENSB_DATA_5_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_5)"
|
|
bitfld.long 0x19c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX2_RX3:ALT6,SD2_DATA1:ALT3,ATA_DA0:ALT1,FEC_TDATA2:ALT1"
|
|
line.long 0x1a0 "IPU_IPP_IND_SENSB_DATA_6_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_6)"
|
|
bitfld.long 0x1a0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX1:ALT6,SD2_DATA2:ALT3,ATA_DA1:ALT1,FEC_RDATA3:ALT1"
|
|
line.long 0x1a4 "IPU_IPP_IND_SENSB_DATA_7_SELECT_INPUT,Software Select Input Control Registers (IPU_IPP_IND_SENSB_DATA_7)"
|
|
bitfld.long 0x1a4 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "TX0:ALT6,SD2_DATA3:ALT3,ATA_DA2:ALT1,FEC_TDATA3:ALT1"
|
|
line.long 0x1a8 "KPP_IPP_IND_COL_0_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_0)"
|
|
bitfld.long 0x1a8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D8:ALT1,TX2_RX3:ALT7,ATA_DMARQ:ALT3,?..."
|
|
line.long 0x1ac "KPP_IPP_IND_COL_1_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_1)"
|
|
bitfld.long 0x1ac 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D9:ALT1,TX1:ALT7,ATA_DA0:ALT3,?..."
|
|
line.long 0x1b0 "KPP_IPP_IND_COL_2_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_2)"
|
|
bitfld.long 0x1b0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D10:ALT1,TX0:ALT7,ATA_DA1:ALT3,?..."
|
|
line.long 0x1b4 "KPP_IPP_IND_COL_3_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_3)"
|
|
bitfld.long 0x1b4 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D11:ALT1,HCKT:ALT7,ATA_DA2:ALT3,?..."
|
|
line.long 0x1b8 "KPP_IPP_IND_COL_4_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_4)"
|
|
bitfld.long 0x1b8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RXD1:ALT4,FEC_RX_ERR:ALT4"
|
|
line.long 0x1bc "KPP_IPP_IND_COL_5_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_5)"
|
|
bitfld.long 0x1bc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TXD1:ALT4,FEC_CRS:ALT4"
|
|
line.long 0x1c0 "KPP_IPP_IND_COL_6_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_6)"
|
|
bitfld.long 0x1c0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RTS1:ALT4,FEC_RDATA1:ALT4"
|
|
line.long 0x1c4 "KPP_IPP_IND_COL_7_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_COL_7)"
|
|
bitfld.long 0x1c4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CTS1:ALT4,FEC_TDATA1:ALT4"
|
|
line.long 0x1c8 "KPP_IPP_IND_ROW_0_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_0)"
|
|
bitfld.long 0x1c8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D12:ALT1,TX4_RX1:ALT7,ATA_DATA14:ALT3,?..."
|
|
line.long 0x1cc "KPP_IPP_IND_ROW_1_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_1)"
|
|
bitfld.long 0x1cc 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D13:ALT1,TX3_RX2:ALT7,ATA_DATA15:ALT3,?..."
|
|
line.long 0x1d0 "KPP_IPP_IND_ROW_2_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_2)"
|
|
bitfld.long 0x1d0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D14:ALT1,SCKT:ALT7,ATA_INTRQ:ALT3,?..."
|
|
line.long 0x1d4 "KPP_IPP_IND_ROW_3_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_3)"
|
|
bitfld.long 0x1d4 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "CSI_D15:ALT1,FST:ALT7,ATA_BUFF_EN:ALT3,?..."
|
|
line.long 0x1d8 "KPP_IPP_IND_ROW_4_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_4)"
|
|
bitfld.long 0x1d8 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RXD2:ALT4,FEC_RDATA2:ALT4"
|
|
line.long 0x1dc "KPP_IPP_IND_ROW_5_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_5)"
|
|
bitfld.long 0x1dc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "TXD2:ALT4,FEC_TDATA2:ALT4"
|
|
line.long 0x1e0 "KPP_IPP_IND_ROW_6_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_6)"
|
|
bitfld.long 0x1e0 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "RTS2:ALT4,FEC_RDATA3:ALT4"
|
|
line.long 0x1e4 "KPP_IPP_IND_ROW_7_SELECT_INPUT,Software Select Input Control Registers (KPP_IPP_IND_ROW_7)"
|
|
bitfld.long 0x1e4 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "CTS2:ALT4,FEC_TDATA3:ALT4"
|
|
line.long 0x1e8 "OWIRE_BATTERY_LINE_IN_SELECT_INPUT,Software Select Input Control Registers (OWIRE_BATTERY_LINE_IN)"
|
|
bitfld.long 0x1e8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "GPIO1_0:ALT2,CSPI1_SS0:ALT1,FEC_TX_ERR:ALT1,?..."
|
|
line.long 0x1ec "SPDIF_HCKT_CLK2_SELECT_SELECT_INPUT,Software Select Input Control Registers (SPDIF_HCKT_CLK2_SELECT)"
|
|
bitfld.long 0x1ec 0.--2. " DAISY ,Selecting Pads Involved in Daisy Chain" "SCK5:ALT1,TX0:ALT1,TXD2:ALT1,SD2_DATA0:ALT6,FEC_TX_ERR:ALT2,?..."
|
|
line.long 0x1f0 "SPDIF_SPDIF_IN1_SELECT_SELECT_INPUT,Software Select Input Control Registers (SPDIF_SPDIF_IN1_SELECT)"
|
|
bitfld.long 0x1f0 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "SRXD5:ALT1,RTS2:ALT1,SD2_CLK:ALT6,FEC_TX_EN:ALT1"
|
|
line.long 0x1f4 "UART3_IPP_UART_RTS_B_SELECT_SELECT_INPUT,Software Select Input Control Registers (UART3_IPP_UART_RTS_B_SELECT)"
|
|
bitfld.long 0x1f4 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA2:ALT1,ATA_DATA8:ALT1,FEC_RX_DV:ALT2,?..."
|
|
line.long 0x1f8 "UART3_IPP_UART_RXD_MUX_SELECT_INPUT,Software Select Input Control Registers (UART3_IPP_UART_RXD_MUX)"
|
|
bitfld.long 0x1f8 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "RTS2:ALT7,SD2_DATA0:ALT1,ATA_DATA10:ALT1,FEC_TX_CLK:ALT2"
|
|
line.long 0x1fc "USB_TOP_IPP_IND_OTG_DATA_0_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_0)"
|
|
bitfld.long 0x1fc 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_DATA1:ALT4,ATA_RESET_B:ALT2"
|
|
line.long 0x200 "USB_TOP_IPP_IND_OTG_DATA_1_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_1)"
|
|
bitfld.long 0x200 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_DATA2:ALT4,ATA_IORDY:ALT2"
|
|
line.long 0x204 "USB_TOP_IPP_IND_OTG_DATA_2_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_2)"
|
|
bitfld.long 0x204 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_DATA3:ALT4,ATA_DATA0:ALT2"
|
|
line.long 0x208 "USB_TOP_IPP_IND_OTG_DATA_3_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_3)"
|
|
bitfld.long 0x208 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD18:ALT4,ATA_DATA1:ALT2"
|
|
line.long 0x20c "USB_TOP_IPP_IND_OTG_DATA_4_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_4)"
|
|
bitfld.long 0x20c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_CMD:ALT4,ATA_DATA2:ALT2"
|
|
line.long 0x210 "USB_TOP_IPP_IND_OTG_DATA_5_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_5)"
|
|
bitfld.long 0x210 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_CLK:ALT4,ATA_DATA3:ALT2"
|
|
line.long 0x214 "USB_TOP_IPP_IND_OTG_DATA_6_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_6)"
|
|
bitfld.long 0x214 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD1_DATA0:ALT4,ATA_DATA4:ALT2"
|
|
line.long 0x218 "USB_TOP_IPP_IND_OTG_DATA_7_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DATA_7)"
|
|
bitfld.long 0x218 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD23:ALT4,ATA_DATA5:ALT2"
|
|
line.long 0x21c "USB_TOP_IPP_IND_OTG_DIR_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_DIR)"
|
|
bitfld.long 0x21c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD19:ALT4,ATA_DIOR:ALT2"
|
|
line.long 0x220 "USB_TOP_IPP_IND_OTG_NXT_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_OTG_NXT)"
|
|
bitfld.long 0x220 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "LD22:ALT4,ATA_DMACK:ALT2"
|
|
line.long 0x224 "USB_TOP_IPP_IND_UH2_DATA_0_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_0)"
|
|
bitfld.long 0x224 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA1:ALT4,FEC_COL:ALT3"
|
|
line.long 0x228 "USB_TOP_IPP_IND_UH2_DATA_1_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_1)"
|
|
bitfld.long 0x228 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA2:ALT4,FEC_RDATA0:ALT3"
|
|
line.long 0x22c "USB_TOP_IPP_IND_UH2_DATA_2_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_2)"
|
|
bitfld.long 0x22c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA3:ALT4,FEC_TDATA0:ALT3"
|
|
line.long 0x230 "USB_TOP_IPP_IND_UH2_DATA_3_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_3)"
|
|
bitfld.long 0x230 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFWE_B:ALT1,FEC_TX_EN:ALT3"
|
|
line.long 0x234 "USB_TOP_IPP_IND_UH2_DATA_4_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_4)"
|
|
bitfld.long 0x234 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_CMD:ALT4,FEC_MDC:ALT3"
|
|
line.long 0x238 "USB_TOP_IPP_IND_UH2_DATA_5_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_5)"
|
|
bitfld.long 0x238 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_CLK:ALT4,FEC_MDIO:ALT3"
|
|
line.long 0x23c "USB_TOP_IPP_IND_UH2_DATA_6_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_6)"
|
|
bitfld.long 0x23c 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "SD2_DATA0:ALT4,FEC_TX_ERR:ALT3"
|
|
line.long 0x240 "USB_TOP_IPP_IND_UH2_DATA_7_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DATA_7)"
|
|
bitfld.long 0x240 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFWP_B:ALT1,FEC_RX_ERR:ALT3"
|
|
line.long 0x244 "USB_TOP_IPP_IND_UH2_DIR_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_DIR)"
|
|
bitfld.long 0x244 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFRE_B:ALT1,FEC_TX_CLK:ALT3"
|
|
line.long 0x248 "USB_TOP_IPP_IND_UH2_NXT_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_NXT)"
|
|
bitfld.long 0x248 0. " DAISY ,Selecting Pads Involved in Daisy Chain" "NFCLE:ALT1,FEC_RX_DV:ALT3"
|
|
line.long 0x24c "USB_TOP_IPP_IND_UH2_USB_OC_SELECT_INPUT,Software Select Input Control Registers (USB_TOP_IPP_IND_UH2_USB_OC)"
|
|
bitfld.long 0x24c 0.--1. " DAISY ,Selecting Pads Involved in Daisy Chain" "I2C2_DAT:ALT2,USBOTG_OC:ALT1,FEC_RDATA1:ALT3,?..."
|
|
tree.end
|
|
width 29.
|
|
tree "SW_PAD_CTL Generic (GPIO Type) Registers"
|
|
group.long 0x328--0x367
|
|
line.long 0x0 "SW_PAD_CTL_PAD_CAPTURE,SW_PAD_CTL Generic (CAPTURE)"
|
|
bitfld.long 0x0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_COMPARE,SW_PAD_CTL Generic (COMPARE)"
|
|
bitfld.long 0x4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_WDOG_RST,SW_PAD_CTL Generic (WDOG_RST)"
|
|
bitfld.long 0x8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_GPIO1_0,SW_PAD_CTL Generic (GPIO1_0)"
|
|
bitfld.long 0xC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xC 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_GPIO1_1,SW_PAD_CTL Generic (GPIO1_1)"
|
|
bitfld.long 0x10 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x10 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x14 "SW_PAD_CTL_PAD_GPIO2_0,SW_PAD_CTL Generic (GPIO2_0)"
|
|
bitfld.long 0x14 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x14 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x14 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x18 "SW_PAD_CTL_PAD_GPIO3_0,SW_PAD_CTL Generic (GPIO3_0)"
|
|
bitfld.long 0x18 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x18 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x18 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1C "SW_PAD_CTL_PAD_RESET_IN_B,SW_PAD_CTL Generic (RESET_IN_B)"
|
|
bitfld.long 0x1C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_POR_B,SW_PAD_CTL Generic (POR_B)"
|
|
bitfld.long 0x20 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_CLKO,SW_PAD_CTL Generic (CLKO)"
|
|
bitfld.long 0x24 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x24 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x24 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x28 "SW_PAD_CTL_PAD_BOOT_MODE0,SW_PAD_CTL Generic (BOOT_MODE0)"
|
|
bitfld.long 0x28 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x28 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x2C "SW_PAD_CTL_PAD_BOOT_MODE1,SW_PAD_CTL Generic (BOOT_MODE1)"
|
|
bitfld.long 0x2C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x2C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x30 "SW_PAD_CTL_PAD_CLK_MODE0,SW_PAD_CTL Generic (CLK_MODE0)"
|
|
bitfld.long 0x30 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x30 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x34 "SW_PAD_CTL_PAD_CLK_MODE1,SW_PAD_CTL Generic (CLK_MODE1)"
|
|
bitfld.long 0x34 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x34 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x38 "SW_PAD_CTL_PAD_POWER_FAIL,SW_PAD_CTL Generic (POWER_FAIL)"
|
|
bitfld.long 0x38 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x38 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x3C "SW_PAD_CTL_PAD_VSTBY,SW_PAD_CTL Generic (VSTBY)"
|
|
bitfld.long 0x3C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x3C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x3C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x390++0x03
|
|
line.long 0x00 "SW_PAD_CTL_PAD_A10,SW_PAD_CTL Generic (A10)"
|
|
bitfld.long 0x00 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x00 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x00 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x3a4--0x3d3
|
|
line.long 0x0 "SW_PAD_CTL_PAD_A14,SW_PAD_CTL Generic (A14)"
|
|
bitfld.long 0x0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_A15,SW_PAD_CTL Generic (A15)"
|
|
bitfld.long 0x4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_A16,SW_PAD_CTL Generic (A16)"
|
|
bitfld.long 0x8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_A17,SW_PAD_CTL Generic (A17)"
|
|
bitfld.long 0xC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_A18,SW_PAD_CTL Generic (A18)"
|
|
bitfld.long 0x10 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x14 "SW_PAD_CTL_PAD_A19,SW_PAD_CTL Generic (A19)"
|
|
bitfld.long 0x14 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x18 "SW_PAD_CTL_PAD_A20,SW_PAD_CTL Generic (A20)"
|
|
bitfld.long 0x18 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x1C "SW_PAD_CTL_PAD_A21,SW_PAD_CTL Generic (A21)"
|
|
bitfld.long 0x1C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_A22,SW_PAD_CTL Generic (A22)"
|
|
bitfld.long 0x20 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_A23,SW_PAD_CTL Generic (A23)"
|
|
bitfld.long 0x24 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x28 "SW_PAD_CTL_PAD_A24,SW_PAD_CTL Generic (A24)"
|
|
bitfld.long 0x28 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x28 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x2C "SW_PAD_CTL_PAD_A25,SW_PAD_CTL Generic (A25)"
|
|
bitfld.long 0x2C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x2C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x46c--0x47f
|
|
line.long 0x0 "SW_PAD_CTL_PAD_EB0,SW_PAD_CTL Generic (EB0)"
|
|
bitfld.long 0x0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_EB1,SW_PAD_CTL Generic (EB1)"
|
|
bitfld.long 0x4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_OE,SW_PAD_CTL Generic (OE)"
|
|
bitfld.long 0x8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_CS0,SW_PAD_CTL Generic (CS0)"
|
|
bitfld.long 0xC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_CS1,SW_PAD_CTL Generic (CS1)"
|
|
bitfld.long 0x10 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x488--0x49b
|
|
line.long 0x0 "SW_PAD_CTL_PAD_CS4,SW_PAD_CTL Generic (CS4)"
|
|
bitfld.long 0x0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x4 "SW_PAD_CTL_PAD_CS5,SW_PAD_CTL Generic (CS5)"
|
|
bitfld.long 0x4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x8 "SW_PAD_CTL_PAD_NF_CE0,SW_PAD_CTL Generic (NF_CE0)"
|
|
bitfld.long 0x8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xC "SW_PAD_CTL_PAD_ECB,SW_PAD_CTL Generic (ECB)"
|
|
bitfld.long 0xC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_LBA,SW_PAD_CTL Generic (LBA)"
|
|
bitfld.long 0x10 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x4a0++0x03
|
|
line.long 0x00 "SW_PAD_CTL_PAD_RW,SW_PAD_CTL Generic (RW)"
|
|
bitfld.long 0x00 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x00 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
group.long 0x4cc++0x2c7
|
|
line.long 0x0 "SW_PAD_CTL_PAD_NFWE_B,SW_PAD_CTL Generic (NFWE_B)"
|
|
bitfld.long 0x0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x4 "SW_PAD_CTL_PAD_NFRE_B,SW_PAD_CTL Generic (NFRE_B)"
|
|
bitfld.long 0x4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x8 "SW_PAD_CTL_PAD_NFALE,SW_PAD_CTL Generic (NFALE)"
|
|
bitfld.long 0x8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xC "SW_PAD_CTL_PAD_NFCLE,SW_PAD_CTL Generic (NFCLE)"
|
|
bitfld.long 0xC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x10 "SW_PAD_CTL_PAD_NFWP_B,SW_PAD_CTL Generic (NFWP_B)"
|
|
bitfld.long 0x10 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x10 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x10 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x14 "SW_PAD_CTL_PAD_NFRB,SW_PAD_CTL Generic (NFRB)"
|
|
bitfld.long 0x14 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x14 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x14 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x18 "SW_PAD_CTL_PAD_D15,SW_PAD_CTL Generic (D15)"
|
|
bitfld.long 0x18 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x18 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x1C "SW_PAD_CTL_PAD_D14,SW_PAD_CTL Generic (D14)"
|
|
bitfld.long 0x1C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_D13,SW_PAD_CTL Generic (D13)"
|
|
bitfld.long 0x20 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x20 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_D12,SW_PAD_CTL Generic (D12)"
|
|
bitfld.long 0x24 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x24 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x28 "SW_PAD_CTL_PAD_D11,SW_PAD_CTL Generic (D11)"
|
|
bitfld.long 0x28 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x28 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x28 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x2C "SW_PAD_CTL_PAD_D10,SW_PAD_CTL Generic (D10)"
|
|
bitfld.long 0x2C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x2C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x30 "SW_PAD_CTL_PAD_D9,SW_PAD_CTL Generic (D9)"
|
|
bitfld.long 0x30 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x30 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x30 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x34 "SW_PAD_CTL_PAD_D8,SW_PAD_CTL Generic (D8)"
|
|
bitfld.long 0x34 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x34 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x34 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x38 "SW_PAD_CTL_PAD_D7,SW_PAD_CTL Generic (D7)"
|
|
bitfld.long 0x38 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x38 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x38 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x3C "SW_PAD_CTL_PAD_D6,SW_PAD_CTL Generic (D6)"
|
|
bitfld.long 0x3C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x3C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x3C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x40 "SW_PAD_CTL_PAD_D5,SW_PAD_CTL Generic (D5)"
|
|
bitfld.long 0x40 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x40 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x40 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x44 "SW_PAD_CTL_PAD_D4,SW_PAD_CTL Generic (D4)"
|
|
bitfld.long 0x44 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x44 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x44 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x48 "SW_PAD_CTL_PAD_D3,SW_PAD_CTL Generic (D3)"
|
|
bitfld.long 0x48 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x48 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x48 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x4C "SW_PAD_CTL_PAD_D2,SW_PAD_CTL Generic (D2)"
|
|
bitfld.long 0x4C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x4C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x4C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x50 "SW_PAD_CTL_PAD_D1,SW_PAD_CTL Generic (D1)"
|
|
bitfld.long 0x50 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x50 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x50 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x50 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x54 "SW_PAD_CTL_PAD_D0,SW_PAD_CTL Generic (D0)"
|
|
bitfld.long 0x54 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x54 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x54 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Keeper,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Pull/Kepper Disabled;Pull,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Keeper,Enabled;Pull,Enabled;Pull,Enabled;Pull,Enabled;Pull"
|
|
textline " "
|
|
bitfld.long 0x54 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x58 "SW_PAD_CTL_PAD_CSI_D8,SW_PAD_CTL Generic (CSI_D8)"
|
|
bitfld.long 0x58 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x58 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x58 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x58 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x58 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x58 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x5C "SW_PAD_CTL_PAD_CSI_D9,SW_PAD_CTL Generic (CSI_D9)"
|
|
bitfld.long 0x5C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x5C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x5C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x5C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x5C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x5C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x60 "SW_PAD_CTL_PAD_CSI_D10,SW_PAD_CTL Generic (CSI_D10)"
|
|
bitfld.long 0x60 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x60 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x60 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x60 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x60 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x60 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x64 "SW_PAD_CTL_PAD_CSI_D11,SW_PAD_CTL Generic (CSI_D11)"
|
|
bitfld.long 0x64 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x64 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x64 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x64 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x64 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x64 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x68 "SW_PAD_CTL_PAD_CSI_D12,SW_PAD_CTL Generic (CSI_D12)"
|
|
bitfld.long 0x68 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x68 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x68 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x68 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x68 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x6C "SW_PAD_CTL_PAD_CSI_D13,SW_PAD_CTL Generic (CSI_D13)"
|
|
bitfld.long 0x6C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x6C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x6C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x6C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x6C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x70 "SW_PAD_CTL_PAD_CSI_D14,SW_PAD_CTL Generic (CSI_D14)"
|
|
bitfld.long 0x70 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x70 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x70 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x70 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x70 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x74 "SW_PAD_CTL_PAD_CSI_D15,SW_PAD_CTL Generic (CSI_D15)"
|
|
bitfld.long 0x74 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x74 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x74 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x74 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x74 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x78 "SW_PAD_CTL_PAD_CSI_MCLK,SW_PAD_CTL Generic (CSI_MCLK)"
|
|
bitfld.long 0x78 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x78 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x78 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x78 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x7C "SW_PAD_CTL_PAD_CSI_VSYNC,SW_PAD_CTL Generic (CSI_VSYNC)"
|
|
bitfld.long 0x7C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x7C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x7C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x7C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x7C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x80 "SW_PAD_CTL_PAD_CSI_HSYNC,SW_PAD_CTL Generic (CSI_HSYNC)"
|
|
bitfld.long 0x80 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x80 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x80 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x80 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x80 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x84 "SW_PAD_CTL_PAD_CSI_PIXCLK,SW_PAD_CTL Generic (CSI_PIXCLK)"
|
|
bitfld.long 0x84 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x84 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x84 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x84 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x84 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x88 "SW_PAD_CTL_PAD_I2C1_CLK,SW_PAD_CTL Generic (I2C1_CLK)"
|
|
bitfld.long 0x88 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x88 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x88 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x88 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x88 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x88 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x8C "SW_PAD_CTL_PAD_I2C1_DAT,SW_PAD_CTL Generic (I2C1_DAT)"
|
|
bitfld.long 0x8C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x8C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x8C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x8C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x90 "SW_PAD_CTL_PAD_I2C2_CLK,SW_PAD_CTL Generic (I2C2_CLK)"
|
|
bitfld.long 0x90 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x90 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x90 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x90 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x90 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x90 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x94 "SW_PAD_CTL_PAD_I2C2_DAT,SW_PAD_CTL Generic (I2C2_DAT)"
|
|
bitfld.long 0x94 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x94 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x94 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x94 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x94 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x94 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x98 "SW_PAD_CTL_PAD_STXD4,SW_PAD_CTL Generic (STXD4)"
|
|
bitfld.long 0x98 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x98 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x98 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x98 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x9C "SW_PAD_CTL_PAD_SRXD4,SW_PAD_CTL Generic (SRXD4)"
|
|
bitfld.long 0x9C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x9C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x9C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x9C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xA0 "SW_PAD_CTL_PAD_SCK4,SW_PAD_CTL Generic (SCK4)"
|
|
bitfld.long 0xA0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xA0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xA0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xA0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xA4 "SW_PAD_CTL_PAD_STXFS4,SW_PAD_CTL Generic (STXFS4)"
|
|
bitfld.long 0xA4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xA4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xA4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xA4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xA8 "SW_PAD_CTL_PAD_STXD5,SW_PAD_CTL Generic (STXD5)"
|
|
bitfld.long 0xA8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xA8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xA8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xA8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xAC "SW_PAD_CTL_PAD_SRXD5,SW_PAD_CTL Generic (SRXD5)"
|
|
bitfld.long 0xAC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xAC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xAC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xAC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xB0 "SW_PAD_CTL_PAD_SCK5,SW_PAD_CTL Generic (SCK5)"
|
|
bitfld.long 0xB0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xB0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xB0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xB0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xB0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xB4 "SW_PAD_CTL_PAD_STXFS5,SW_PAD_CTL Generic (STXFS5)"
|
|
bitfld.long 0xB4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xB4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xB4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xB4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xB8 "SW_PAD_CTL_PAD_SCKR,SW_PAD_CTL Generic (SCKR)"
|
|
bitfld.long 0xB8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xB8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xB8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xB8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xB8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xBC "SW_PAD_CTL_PAD_FSR,SW_PAD_CTL Generic (FSR)"
|
|
bitfld.long 0xBC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xBC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xBC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xBC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xBC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xC0 "SW_PAD_CTL_PAD_HCKR,SW_PAD_CTL Generic (HCKR)"
|
|
bitfld.long 0xC0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xC0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xC0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xC4 "SW_PAD_CTL_PAD_SCKT,SW_PAD_CTL Generic (SCKT)"
|
|
bitfld.long 0xC4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xC4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xC4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xC8 "SW_PAD_CTL_PAD_FST,SW_PAD_CTL Generic (FST)"
|
|
bitfld.long 0xC8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xC8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xC8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xC8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xCC "SW_PAD_CTL_PAD_HCKT,SW_PAD_CTL Generic (HCKT)"
|
|
bitfld.long 0xCC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xCC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xCC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xCC 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xCC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xCC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xD0 "SW_PAD_CTL_PAD_TX5_RX0,SW_PAD_CTL Generic (TX5_RX0)"
|
|
bitfld.long 0xD0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xD0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xD0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xD0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xD0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xD4 "SW_PAD_CTL_PAD_TX4_RX1,SW_PAD_CTL Generic (TX4_RX1)"
|
|
bitfld.long 0xD4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xD4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xD4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xD4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xD4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xD8 "SW_PAD_CTL_PAD_TX3_RX2,SW_PAD_CTL Generic (TX3_RX2)"
|
|
bitfld.long 0xD8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xD8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xD8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xD8 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xD8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xD8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xDC "SW_PAD_CTL_PAD_TX2_RX3,SW_PAD_CTL Generic (TX2_RX3)"
|
|
bitfld.long 0xDC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xDC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xDC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xDC 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xDC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xDC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xE0 "SW_PAD_CTL_PAD_TX1,SW_PAD_CTL Generic (TX1)"
|
|
bitfld.long 0xE0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xE0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xE0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xE0 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xE0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xE0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xE4 "SW_PAD_CTL_PAD_TX0,SW_PAD_CTL Generic (TX0)"
|
|
bitfld.long 0xE4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xE4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xE4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xE4 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xE4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0xE4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0xE8 "SW_PAD_CTL_PAD_CSPI1_MOSI,SW_PAD_CTL Generic (CSPI1_MOSI)"
|
|
bitfld.long 0xE8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xE8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xE8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xE8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xEC "SW_PAD_CTL_PAD_CSPI1_MISO,SW_PAD_CTL Generic (CSPI1_MISO)"
|
|
bitfld.long 0xEC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xEC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xEC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xEC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xF0 "SW_PAD_CTL_PAD_CSPI1_SS0,SW_PAD_CTL Generic (CSPI1_SS0)"
|
|
bitfld.long 0xF0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xF0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xF0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xF0 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0xF0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xF4 "SW_PAD_CTL_PAD_CSPI1_SS1,SW_PAD_CTL Generic (CSPI1_SS1)"
|
|
bitfld.long 0xF4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xF4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xF4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xF4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xF8 "SW_PAD_CTL_PAD_CSPI1_SCLK,SW_PAD_CTL Generic (CSPI1_SCLK)"
|
|
bitfld.long 0xF8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xF8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xF8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xF8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0xFC "SW_PAD_CTL_PAD_CSPI1_SPI_RDY,SW_PAD_CTL Generic (CSPI1_SPI_RDY)"
|
|
bitfld.long 0xFC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0xFC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xFC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0xFC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x100 "SW_PAD_CTL_PAD_RXD1,SW_PAD_CTL Generic (RXD1)"
|
|
bitfld.long 0x100 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x100 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x100 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x100 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x100 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x104 "SW_PAD_CTL_PAD_TXD1,SW_PAD_CTL Generic (TXD1)"
|
|
bitfld.long 0x104 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x104 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x104 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x104 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x104 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x108 "SW_PAD_CTL_PAD_RTS1,SW_PAD_CTL Generic (RTS1)"
|
|
bitfld.long 0x108 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x108 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x108 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x108 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x108 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x108 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x10C "SW_PAD_CTL_PAD_CTS1,SW_PAD_CTL Generic (CTS1)"
|
|
bitfld.long 0x10C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x10C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x10C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x10C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x10C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x110 "SW_PAD_CTL_PAD_RXD2,SW_PAD_CTL Generic (RXD2)"
|
|
bitfld.long 0x110 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x110 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x110 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x110 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x114 "SW_PAD_CTL_PAD_TXD2,SW_PAD_CTL Generic (TXD2)"
|
|
bitfld.long 0x114 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x114 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x114 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x114 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x114 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x118 "SW_PAD_CTL_PAD_RTS2,SW_PAD_CTL Generic (RTS2)"
|
|
bitfld.long 0x118 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x118 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x118 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x118 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x118 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x11C "SW_PAD_CTL_PAD_CTS2,SW_PAD_CTL Generic (CTS2)"
|
|
bitfld.long 0x11C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x11C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x11C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x11C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x11C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x120 "SW_PAD_CTL_PAD_RTCK,SW_PAD_CTL Generic (RTCK)"
|
|
bitfld.long 0x120 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x120 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x120 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x120 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x124 "SW_PAD_CTL_PAD_TCK,SW_PAD_CTL Generic (TCK)"
|
|
bitfld.long 0x124 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x124 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x124 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x124 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x124 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x128 "SW_PAD_CTL_PAD_TMS,SW_PAD_CTL Generic (TMS)"
|
|
bitfld.long 0x128 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x128 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x128 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x128 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x128 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x12C "SW_PAD_CTL_PAD_TDI,SW_PAD_CTL Generic (TDI)"
|
|
bitfld.long 0x12C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x12C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x12C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x12C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x12C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x130 "SW_PAD_CTL_PAD_TDO,SW_PAD_CTL Generic (TDO)"
|
|
bitfld.long 0x130 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x130 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x130 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x130 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x130 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x134 "SW_PAD_CTL_PAD_TRSTB,SW_PAD_CTL Generic (TRSTB)"
|
|
bitfld.long 0x134 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x134 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x134 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x134 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x134 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x138 "SW_PAD_CTL_PAD_DE_B,SW_PAD_CTL Generic (DE_B)"
|
|
bitfld.long 0x138 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x138 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x138 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x138 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x138 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x13C "SW_PAD_CTL_PAD_SJC_MOD,SW_PAD_CTL Generic (SJC_MOD)"
|
|
bitfld.long 0x13C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x13C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x13C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x13C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x13C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x140 "SW_PAD_CTL_PAD_USBOTG_PWR,SW_PAD_CTL Generic (USBOTG_PWR)"
|
|
bitfld.long 0x140 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x140 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x140 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x140 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x144 "SW_PAD_CTL_PAD_USBOTG_OC,SW_PAD_CTL Generic (USBOTG_OC)"
|
|
bitfld.long 0x144 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x144 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x144 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x144 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x144 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x148 "SW_PAD_CTL_PAD_LD0,SW_PAD_CTL Generic (LD0)"
|
|
bitfld.long 0x148 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x148 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x148 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x148 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x148 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x14C "SW_PAD_CTL_PAD_LD1,SW_PAD_CTL Generic (LD1)"
|
|
bitfld.long 0x14C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x14C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x14C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x14C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x150 "SW_PAD_CTL_PAD_LD2,SW_PAD_CTL Generic (LD2)"
|
|
bitfld.long 0x150 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x150 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x150 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x150 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x150 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x154 "SW_PAD_CTL_PAD_LD3,SW_PAD_CTL Generic (LD3)"
|
|
bitfld.long 0x154 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x154 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x154 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x154 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x154 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x158 "SW_PAD_CTL_PAD_LD4,SW_PAD_CTL Generic (LD4)"
|
|
bitfld.long 0x158 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x158 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x158 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x158 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x158 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x15C "SW_PAD_CTL_PAD_LD5,SW_PAD_CTL Generic (LD5)"
|
|
bitfld.long 0x15C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x15C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x15C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x15C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x15C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x160 "SW_PAD_CTL_PAD_LD6,SW_PAD_CTL Generic (LD6)"
|
|
bitfld.long 0x160 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x160 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x160 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x160 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x160 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x164 "SW_PAD_CTL_PAD_LD7,SW_PAD_CTL Generic (LD7)"
|
|
bitfld.long 0x164 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x164 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x164 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x164 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x164 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x168 "SW_PAD_CTL_PAD_LD8,SW_PAD_CTL Generic (LD8)"
|
|
bitfld.long 0x168 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x168 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x168 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x168 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x168 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x16C "SW_PAD_CTL_PAD_LD9,SW_PAD_CTL Generic (LD9)"
|
|
bitfld.long 0x16C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x16C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x16C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x16C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x16C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x170 "SW_PAD_CTL_PAD_LD10,SW_PAD_CTL Generic (LD10)"
|
|
bitfld.long 0x170 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x170 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x170 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x170 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x170 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x174 "SW_PAD_CTL_PAD_LD11,SW_PAD_CTL Generic (LD11)"
|
|
bitfld.long 0x174 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x174 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x174 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x174 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x174 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x178 "SW_PAD_CTL_PAD_LD12,SW_PAD_CTL Generic (LD12)"
|
|
bitfld.long 0x178 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x178 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x178 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x178 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x178 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x17C "SW_PAD_CTL_PAD_LD13,SW_PAD_CTL Generic (LD13)"
|
|
bitfld.long 0x17C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x17C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x17C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x17C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x17C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x180 "SW_PAD_CTL_PAD_LD14,SW_PAD_CTL Generic (LD14)"
|
|
bitfld.long 0x180 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x180 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x180 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x180 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x180 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x184 "SW_PAD_CTL_PAD_LD15,SW_PAD_CTL Generic (LD15)"
|
|
bitfld.long 0x184 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x184 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x184 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x184 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x184 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x188 "SW_PAD_CTL_PAD_LD16,SW_PAD_CTL Generic (LD16)"
|
|
bitfld.long 0x188 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x188 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x188 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x188 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x188 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x18C "SW_PAD_CTL_PAD_LD17,SW_PAD_CTL Generic (LD17)"
|
|
bitfld.long 0x18C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x18C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x18C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x18C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x190 "SW_PAD_CTL_PAD_LD18,SW_PAD_CTL Generic (LD18)"
|
|
bitfld.long 0x190 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x190 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x190 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x190 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x190 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x194 "SW_PAD_CTL_PAD_LD19,SW_PAD_CTL Generic (LD19)"
|
|
bitfld.long 0x194 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x194 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x194 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x194 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x194 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x198 "SW_PAD_CTL_PAD_LD20,SW_PAD_CTL Generic (LD20)"
|
|
bitfld.long 0x198 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x198 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x198 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x198 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x198 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x19C "SW_PAD_CTL_PAD_LD21,SW_PAD_CTL Generic (LD21)"
|
|
bitfld.long 0x19C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x19C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x19C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x19C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x19C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1A0 "SW_PAD_CTL_PAD_LD22,SW_PAD_CTL Generic (LD22)"
|
|
bitfld.long 0x1A0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1A0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1A0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1A0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1A0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1A4 "SW_PAD_CTL_PAD_LD23,SW_PAD_CTL Generic (LD23)"
|
|
bitfld.long 0x1A4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1A4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1A4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1A4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1A4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1A8 "SW_PAD_CTL_PAD_D3_HSYNC,SW_PAD_CTL Generic (D3_HSYNC)"
|
|
bitfld.long 0x1A8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1A8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1A8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1A8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1A8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1AC "SW_PAD_CTL_PAD_D3_FPSHIFT,SW_PAD_CTL Generic (D3_FPSHIFT)"
|
|
bitfld.long 0x1AC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1AC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1AC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1AC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1B0 "SW_PAD_CTL_PAD_D3_DRDY,SW_PAD_CTL Generic (D3_DRDY)"
|
|
bitfld.long 0x1B0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1B0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1B0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1B0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1B4 "SW_PAD_CTL_PAD_CONTRAST,SW_PAD_CTL Generic (CONTRAST)"
|
|
bitfld.long 0x1B4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1B4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1B4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1B4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1B8 "SW_PAD_CTL_PAD_D3_VSYNC,SW_PAD_CTL Generic (D3_VSYNC)"
|
|
bitfld.long 0x1B8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1B8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1B8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1B8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1BC "SW_PAD_CTL_PAD_D3_REV,SW_PAD_CTL Generic (D3_REV)"
|
|
bitfld.long 0x1BC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1BC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1BC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1BC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1C0 "SW_PAD_CTL_PAD_D3_CLS,SW_PAD_CTL Generic (D3_CLS)"
|
|
bitfld.long 0x1C0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x1C0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1C0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1C0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1C4 "SW_PAD_CTL_PAD_D3_SPL,SW_PAD_CTL Generic (D3_SPL)"
|
|
bitfld.long 0x1C4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1C4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1C4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1C4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1C8 "SW_PAD_CTL_PAD_SD1_CMD,SW_PAD_CTL Generic (SD1_CMD)"
|
|
bitfld.long 0x1C8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1C8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1C8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1C8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1CC "SW_PAD_CTL_PAD_SD1_CLK,SW_PAD_CTL Generic (SD1_CLK)"
|
|
bitfld.long 0x1CC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1CC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1CC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1CC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1CC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1D0 "SW_PAD_CTL_PAD_SD1_DATA0,SW_PAD_CTL Generic (SD1_DATA0)"
|
|
bitfld.long 0x1D0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1D0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1D0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1D0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1D0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1D4 "SW_PAD_CTL_PAD_SD1_DATA1,SW_PAD_CTL Generic (SD1_DATA1)"
|
|
bitfld.long 0x1D4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1D4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1D4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1D4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1D4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1D8 "SW_PAD_CTL_PAD_SD1_DATA2,SW_PAD_CTL Generic (SD1_DATA2)"
|
|
bitfld.long 0x1D8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1D8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1D8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1D8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1D8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1DC "SW_PAD_CTL_PAD_SD1_DATA3,SW_PAD_CTL Generic (SD1_DATA3)"
|
|
bitfld.long 0x1DC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1DC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1DC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1DC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1DC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1E0 "SW_PAD_CTL_PAD_SD2_CMD,SW_PAD_CTL Generic (SD2_CMD)"
|
|
bitfld.long 0x1E0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1E0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1E0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1E0 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x1E0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1E0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1E4 "SW_PAD_CTL_PAD_SD2_CLK,SW_PAD_CTL Generic (SD2_CLK)"
|
|
bitfld.long 0x1E4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1E4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1E4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1E4 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x1E4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1E4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1E8 "SW_PAD_CTL_PAD_SD2_DATA0,SW_PAD_CTL Generic (SD2_DATA0)"
|
|
bitfld.long 0x1E8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1E8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1E8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1E8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1E8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1EC "SW_PAD_CTL_PAD_SD2_DATA1,SW_PAD_CTL Generic (SD2_DATA1)"
|
|
bitfld.long 0x1EC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1EC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1EC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1EC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1EC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1F0 "SW_PAD_CTL_PAD_SD2_DATA2,SW_PAD_CTL Generic (SD2_DATA2)"
|
|
bitfld.long 0x1F0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1F0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1F0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1F0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1F0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1F4 "SW_PAD_CTL_PAD_SD2_DATA3,SW_PAD_CTL Generic (SD2_DATA3)"
|
|
bitfld.long 0x1F4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1F4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1F4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1F4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1F4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1F8 "SW_PAD_CTL_PAD_ATA_CS0,SW_PAD_CTL Generic (ATA_CS0)"
|
|
bitfld.long 0x1F8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1F8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1F8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1F8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1F8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x1FC "SW_PAD_CTL_PAD_ATA_CS1,SW_PAD_CTL Generic (ATA_CS1)"
|
|
bitfld.long 0x1FC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x1FC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1FC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x1FC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x1FC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x200 "SW_PAD_CTL_PAD_ATA_DIOR,SW_PAD_CTL Generic (ATA_DIOR)"
|
|
bitfld.long 0x200 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x200 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x200 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x200 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x200 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x204 "SW_PAD_CTL_PAD_ATA_DIOW,SW_PAD_CTL Generic (ATA_DIOW)"
|
|
bitfld.long 0x204 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x204 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x204 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x204 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x204 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x208 "SW_PAD_CTL_PAD_ATA_DMACK,SW_PAD_CTL Generic (ATA_DMACK)"
|
|
bitfld.long 0x208 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x208 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x208 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x208 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x208 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x20C "SW_PAD_CTL_PAD_ATA_RESET_B,SW_PAD_CTL Generic (ATA_RESET_B)"
|
|
bitfld.long 0x20C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x20C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x20C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x20C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x210 "SW_PAD_CTL_PAD_ATA_IORDY,SW_PAD_CTL Generic (ATA_IORDY)"
|
|
bitfld.long 0x210 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x210 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x210 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x210 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x210 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x214 "SW_PAD_CTL_PAD_ATA_DATA0,SW_PAD_CTL Generic (ATA_DATA0)"
|
|
bitfld.long 0x214 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x214 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x214 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x214 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x214 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x218 "SW_PAD_CTL_PAD_ATA_DATA1,SW_PAD_CTL Generic (ATA_DATA1)"
|
|
bitfld.long 0x218 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x218 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x218 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x218 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x218 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x21C "SW_PAD_CTL_PAD_ATA_DATA2,SW_PAD_CTL Generic (ATA_DATA2)"
|
|
bitfld.long 0x21C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x21C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x21C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x21C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x21C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x220 "SW_PAD_CTL_PAD_ATA_DATA3,SW_PAD_CTL Generic (ATA_DATA3)"
|
|
bitfld.long 0x220 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x220 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x220 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x220 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x220 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x224 "SW_PAD_CTL_PAD_ATA_DATA4,SW_PAD_CTL Generic (ATA_DATA4)"
|
|
bitfld.long 0x224 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x224 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x224 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x224 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x224 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x228 "SW_PAD_CTL_PAD_ATA_DATA5,SW_PAD_CTL Generic (ATA_DATA5)"
|
|
bitfld.long 0x228 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x228 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x228 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x228 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x228 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x22C "SW_PAD_CTL_PAD_ATA_DATA6,SW_PAD_CTL Generic (ATA_DATA6)"
|
|
bitfld.long 0x22C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x22C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x22C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x22C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x230 "SW_PAD_CTL_PAD_ATA_DATA7,SW_PAD_CTL Generic (ATA_DATA7)"
|
|
bitfld.long 0x230 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x230 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x230 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x230 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x234 "SW_PAD_CTL_PAD_ATA_DATA8,SW_PAD_CTL Generic (ATA_DATA8)"
|
|
bitfld.long 0x234 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x234 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x234 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x234 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x238 "SW_PAD_CTL_PAD_ATA_DATA9,SW_PAD_CTL Generic (ATA_DATA9)"
|
|
bitfld.long 0x238 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x238 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x238 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x238 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x23C "SW_PAD_CTL_PAD_ATA_DATA10,SW_PAD_CTL Generic (ATA_DATA10)"
|
|
bitfld.long 0x23C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x23C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x23C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x23C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x240 "SW_PAD_CTL_PAD_ATA_DATA11,SW_PAD_CTL Generic (ATA_DATA11)"
|
|
bitfld.long 0x240 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x240 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x240 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x240 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x244 "SW_PAD_CTL_PAD_ATA_DATA12,SW_PAD_CTL Generic (ATA_DATA12)"
|
|
bitfld.long 0x244 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x244 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x244 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x244 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x244 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x248 "SW_PAD_CTL_PAD_ATA_DATA13,SW_PAD_CTL Generic (ATA_DATA13)"
|
|
bitfld.long 0x248 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x248 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x248 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x248 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x248 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x24C "SW_PAD_CTL_PAD_ATA_DATA14,SW_PAD_CTL Generic (ATA_DATA14)"
|
|
bitfld.long 0x24C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x24C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x24C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x24C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x250 "SW_PAD_CTL_PAD_ATA_DATA15,SW_PAD_CTL Generic (ATA_DATA15)"
|
|
bitfld.long 0x250 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x250 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x250 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x250 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x250 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x254 "SW_PAD_CTL_PAD_ATA_INTRQ,SW_PAD_CTL Generic (ATA_INTRQ)"
|
|
bitfld.long 0x254 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x254 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x254 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x254 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x254 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x258 "SW_PAD_CTL_PAD_ATA_BUFF_EN,SW_PAD_CTL Generic (ATA_BUFF_EN)"
|
|
bitfld.long 0x258 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x258 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x258 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x258 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x258 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x25C "SW_PAD_CTL_PAD_ATA_DMARQ,SW_PAD_CTL Generic (ATA_DMARQ)"
|
|
bitfld.long 0x25C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x25C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x25C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x25C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x25C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x25C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x260 "SW_PAD_CTL_PAD_ATA_DA0,SW_PAD_CTL Generic (ATA_DA0)"
|
|
bitfld.long 0x260 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x260 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x260 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x260 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x260 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x260 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x264 "SW_PAD_CTL_PAD_ATA_DA1,SW_PAD_CTL Generic (ATA_DA1)"
|
|
bitfld.long 0x264 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x264 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x264 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x264 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x264 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x264 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x268 "SW_PAD_CTL_PAD_ATA_DA2,SW_PAD_CTL Generic (ATA_DA2)"
|
|
bitfld.long 0x268 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x268 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x268 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x268 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x268 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x268 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x26C "SW_PAD_CTL_PAD_MLB_CLK,SW_PAD_CTL Generic (MLB_CLK)"
|
|
bitfld.long 0x26C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x26C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x26C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x26C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x26C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x270 "SW_PAD_CTL_PAD_MLB_DAT,SW_PAD_CTL Generic (MLB_DAT)"
|
|
bitfld.long 0x270 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x270 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x270 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x270 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x270 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x274 "SW_PAD_CTL_PAD_MLB_SIG,SW_PAD_CTL Generic (MLB_SIG)"
|
|
bitfld.long 0x274 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x274 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x274 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x274 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x274 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x278 "SW_PAD_CTL_PAD_FEC_TX_CLK,SW_PAD_CTL Generic (FEC_TX_CLK)"
|
|
bitfld.long 0x278 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x278 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x278 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x278 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x278 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x27C "SW_PAD_CTL_PAD_FEC_RX_CLK,SW_PAD_CTL Generic (FEC_RX_CLK)"
|
|
bitfld.long 0x27C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x27C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x27C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x27C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x27C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x280 "SW_PAD_CTL_PAD_FEC_RX_DV,SW_PAD_CTL Generic (FEC_RX_DV)"
|
|
bitfld.long 0x280 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x280 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x280 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x280 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x280 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x284 "SW_PAD_CTL_PAD_FEC_COL,SW_PAD_CTL Generic (FEC_COL)"
|
|
bitfld.long 0x284 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x284 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x284 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x284 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x284 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x288 "SW_PAD_CTL_PAD_FEC_RDATA0,SW_PAD_CTL Generic (FEC_RDATA0)"
|
|
bitfld.long 0x288 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x288 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x288 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x288 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x288 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x28C "SW_PAD_CTL_PAD_FEC_TDATA0,SW_PAD_CTL Generic (FEC_TDATA0)"
|
|
bitfld.long 0x28C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x28C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x28C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x28C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x290 "SW_PAD_CTL_PAD_FEC_TX_EN,SW_PAD_CTL Generic (FEC_TX_EN)"
|
|
bitfld.long 0x290 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x290 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x290 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x290 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x290 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x294 "SW_PAD_CTL_PAD_FEC_MDC,SW_PAD_CTL Generic (FEC_MDC)"
|
|
bitfld.long 0x294 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x294 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x294 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x294 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x294 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x298 "SW_PAD_CTL_PAD_FEC_MDIO,SW_PAD_CTL Generic (FEC_MDIO)"
|
|
bitfld.long 0x298 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x298 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x298 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x298 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x298 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x29C "SW_PAD_CTL_PAD_FEC_TX_ERR,SW_PAD_CTL Generic (FEC_TX_ERR)"
|
|
bitfld.long 0x29C 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x29C 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x29C 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x29C 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x29C 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x29C 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2A0 "SW_PAD_CTL_PAD_FEC_RX_ERR,SW_PAD_CTL Generic (FEC_RX_ERR)"
|
|
bitfld.long 0x2A0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2A0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2A0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2A0 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x2A0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2A0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2A4 "SW_PAD_CTL_PAD_FEC_CRS,SW_PAD_CTL Generic (FEC_CRS)"
|
|
bitfld.long 0x2A4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2A4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2A4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2A4 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x2A4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2A4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2A8 "SW_PAD_CTL_PAD_FEC_RDATA1,SW_PAD_CTL Generic (FEC_RDATA1)"
|
|
bitfld.long 0x2A8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2A8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2A8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2A8 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x2A8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2A8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2AC "SW_PAD_CTL_PAD_FEC_TDATA1,SW_PAD_CTL Generic (FEC_TDATA1)"
|
|
bitfld.long 0x2AC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2AC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2AC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2AC 3. " ODE ,Open drain enable" "Disabled,Enabled"
|
|
bitfld.long 0x2AC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2AC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2B0 "SW_PAD_CTL_PAD_FEC_RDATA2,SW_PAD_CTL Generic (FEC_RDATA2)"
|
|
bitfld.long 0x2B0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2B0 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2B0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2B0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2B0 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2B4 "SW_PAD_CTL_PAD_FEC_TDATA2,SW_PAD_CTL Generic (FEC_TDATA2)"
|
|
bitfld.long 0x2B4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2B4 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2B4 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2B4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2B4 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2B8 "SW_PAD_CTL_PAD_FEC_RDATA3,SW_PAD_CTL Generic (FEC_RDATA3)"
|
|
bitfld.long 0x2B8 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2B8 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2B8 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2B8 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2B8 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2BC "SW_PAD_CTL_PAD_FEC_TDATA3,SW_PAD_CTL Generic (FEC_TDATA3)"
|
|
bitfld.long 0x2BC 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
bitfld.long 0x2BC 8. " HYS ,Hysteresis Enable Field" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2BC 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled;Keeper;100KOhm Pull Down,Pull/Kepper Disabled;Keeper;47KOhm Pull Up,Pull/Kepper Disabled;Keeper;100KOhm Pull Up,Pull/Kepper Disabled;Keeper;22KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Down,Pull/Kepper Disabled;Pull;47KOhm Pull Up,Pull/Kepper Disabled;Pull;100KOhm Pull Up,Pull/Kepper Disabled;Pull;22KOhm Pull Up,Enabled;Keeper;100KOhm Pull Down,Enabled;Keeper;47KOhm Pull Up,Enabled;Keeper;100KOhm Pull Up,Enabled;Keeper;22KOhm Pull Up,Enabled;Pull;100KOhm Pull Down,Enabled;Pull;47KOhm Pull Up,Enabled;Pull;100KOhm Pull Up,Enabled;Pull;22KOhm Pull Up"
|
|
textline " "
|
|
bitfld.long 0x2BC 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
textline " "
|
|
bitfld.long 0x2BC 0. " SRE ,Slew Rate" "Slow,Fast"
|
|
line.long 0x2C0 "SW_PAD_CTL_PAD_EXT_ARMCLK,SW_PAD_CTL Generic (EXT_ARMCLK)"
|
|
bitfld.long 0x2C0 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x2C0 4.--7. " PULL_KEEP_CTL ,Pull Up/ Pull Down/ Keeper Control Field" "Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Pull/Kepper Disabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C0 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
line.long 0x2C4 "SW_PAD_CTL_PAD_TEST_MODE,SW_PAD_CTL Generic (TEST_MODE)"
|
|
bitfld.long 0x2C4 13. " DRIVE_VOLTAGE ,Drive Voltage Select Field" "3.3V,1.8V"
|
|
textline " "
|
|
bitfld.long 0x2C4 1.--2. " DSE ,Drive strength Enable Field" "Nominal,High,Max,?..."
|
|
tree.end
|
|
width 23.
|
|
tree "SW_PAD_CTL Generic (DDR Type) Registers"
|
|
group.long 0x368--0x38f
|
|
line.long 0x0 "SW_PAD_CTL_PAD_A0,SW_PAD_CTL Generic (A0)"
|
|
bitfld.long 0x0 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_A1,SW_PAD_CTL Generic (A1)"
|
|
bitfld.long 0x4 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_A2,SW_PAD_CTL Generic (A2)"
|
|
bitfld.long 0x8 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_A3,SW_PAD_CTL Generic (A3)"
|
|
bitfld.long 0xC 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_A4,SW_PAD_CTL Generic (A4)"
|
|
bitfld.long 0x10 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x14 "SW_PAD_CTL_PAD_A5,SW_PAD_CTL Generic (A5)"
|
|
bitfld.long 0x14 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x18 "SW_PAD_CTL_PAD_A6,SW_PAD_CTL Generic (A6)"
|
|
bitfld.long 0x18 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x1C "SW_PAD_CTL_PAD_A7,SW_PAD_CTL Generic (A7)"
|
|
bitfld.long 0x1C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_A8,SW_PAD_CTL Generic (A8)"
|
|
bitfld.long 0x20 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_A9,SW_PAD_CTL Generic (A9)"
|
|
bitfld.long 0x24 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
group.long 0x394--0x3a3
|
|
line.long 0x0 "SW_PAD_CTL_PAD_MA10,SW_PAD_CTL Generic (MA10)"
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_A11,SW_PAD_CTL Generic (A11)"
|
|
bitfld.long 0x4 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_A12,SW_PAD_CTL Generic (A12)"
|
|
bitfld.long 0x8 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_A13,SW_PAD_CTL Generic (A13)"
|
|
bitfld.long 0xC 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
group.long 0x3d4++0x97
|
|
line.long 0x0 "SW_PAD_CTL_PAD_SDBA1,SW_PAD_CTL Generic (SDBA1)"
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_SDBA0,SW_PAD_CTL Generic (SDBA0)"
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_SD0,SW_PAD_CTL Generic (SD0)"
|
|
bitfld.long 0x8 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_SD1,SW_PAD_CTL Generic (SD1)"
|
|
bitfld.long 0xC 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_SD2,SW_PAD_CTL Generic (SD2)"
|
|
bitfld.long 0x10 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x14 "SW_PAD_CTL_PAD_SD3,SW_PAD_CTL Generic (SD3)"
|
|
bitfld.long 0x14 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x18 "SW_PAD_CTL_PAD_SD4,SW_PAD_CTL Generic (SD4)"
|
|
bitfld.long 0x18 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x1C "SW_PAD_CTL_PAD_SD5,SW_PAD_CTL Generic (SD5)"
|
|
bitfld.long 0x1C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_SD6,SW_PAD_CTL Generic (SD6)"
|
|
bitfld.long 0x20 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_SD7,SW_PAD_CTL Generic (SD7)"
|
|
bitfld.long 0x24 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x28 "SW_PAD_CTL_PAD_SD8,SW_PAD_CTL Generic (SD8)"
|
|
bitfld.long 0x28 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x28 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x2C "SW_PAD_CTL_PAD_SD9,SW_PAD_CTL Generic (SD9)"
|
|
bitfld.long 0x2C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x2C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x30 "SW_PAD_CTL_PAD_SD10,SW_PAD_CTL Generic (SD10)"
|
|
bitfld.long 0x30 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x30 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x34 "SW_PAD_CTL_PAD_SD11,SW_PAD_CTL Generic (SD11)"
|
|
bitfld.long 0x34 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x34 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x38 "SW_PAD_CTL_PAD_SD12,SW_PAD_CTL Generic (SD12)"
|
|
bitfld.long 0x38 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x38 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x3C "SW_PAD_CTL_PAD_SD13,SW_PAD_CTL Generic (SD13)"
|
|
bitfld.long 0x3C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x3C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x40 "SW_PAD_CTL_PAD_SD14,SW_PAD_CTL Generic (SD14)"
|
|
bitfld.long 0x40 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x40 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x44 "SW_PAD_CTL_PAD_SD15,SW_PAD_CTL Generic (SD15)"
|
|
bitfld.long 0x44 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x44 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x48 "SW_PAD_CTL_PAD_SD16,SW_PAD_CTL Generic (SD16)"
|
|
bitfld.long 0x48 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x48 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4C "SW_PAD_CTL_PAD_SD17,SW_PAD_CTL Generic (SD17)"
|
|
bitfld.long 0x4C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x50 "SW_PAD_CTL_PAD_SD18,SW_PAD_CTL Generic (SD18)"
|
|
bitfld.long 0x50 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x50 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x54 "SW_PAD_CTL_PAD_SD19,SW_PAD_CTL Generic (SD19)"
|
|
bitfld.long 0x54 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x54 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x58 "SW_PAD_CTL_PAD_SD20,SW_PAD_CTL Generic (SD20)"
|
|
bitfld.long 0x58 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x58 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x5C "SW_PAD_CTL_PAD_SD21,SW_PAD_CTL Generic (SD21)"
|
|
bitfld.long 0x5C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x5C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x60 "SW_PAD_CTL_PAD_SD22,SW_PAD_CTL Generic (SD22)"
|
|
bitfld.long 0x60 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x60 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x64 "SW_PAD_CTL_PAD_SD23,SW_PAD_CTL Generic (SD23)"
|
|
bitfld.long 0x64 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x64 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x68 "SW_PAD_CTL_PAD_SD24,SW_PAD_CTL Generic (SD24)"
|
|
bitfld.long 0x68 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x68 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x6C "SW_PAD_CTL_PAD_SD25,SW_PAD_CTL Generic (SD25)"
|
|
bitfld.long 0x6C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x6C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x70 "SW_PAD_CTL_PAD_SD26,SW_PAD_CTL Generic (SD26)"
|
|
bitfld.long 0x70 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x70 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x74 "SW_PAD_CTL_PAD_SD27,SW_PAD_CTL Generic (SD27)"
|
|
bitfld.long 0x74 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x74 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x78 "SW_PAD_CTL_PAD_SD28,SW_PAD_CTL Generic (SD28)"
|
|
bitfld.long 0x78 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x78 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x7C "SW_PAD_CTL_PAD_SD29,SW_PAD_CTL Generic (SD29)"
|
|
bitfld.long 0x7C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x7C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x80 "SW_PAD_CTL_PAD_SD30,SW_PAD_CTL Generic (SD30)"
|
|
bitfld.long 0x80 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x80 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x84 "SW_PAD_CTL_PAD_SD31,SW_PAD_CTL Generic (SD31)"
|
|
bitfld.long 0x84 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x84 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x88 "SW_PAD_CTL_PAD_DQM0,SW_PAD_CTL Generic (DQM0)"
|
|
bitfld.long 0x88 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x8C "SW_PAD_CTL_PAD_DQM1,SW_PAD_CTL Generic (DQM1)"
|
|
bitfld.long 0x8C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x90 "SW_PAD_CTL_PAD_DQM2,SW_PAD_CTL Generic (DQM2)"
|
|
bitfld.long 0x90 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x94 "SW_PAD_CTL_PAD_DQM3,SW_PAD_CTL Generic (DQM3)"
|
|
bitfld.long 0x94 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
group.long 0x480++0x07
|
|
line.long 0x0 "SW_PAD_CTL_PAD_CS2,SW_PAD_CTL Generic (CS2)"
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_CS3,SW_PAD_CTL Generic (CS3)"
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
group.long 0x49c++0x03
|
|
line.long 0x00 "SW_PAD_CTL_PAD_BCLK,SW_PAD_CTL Generic (BCLK)"
|
|
bitfld.long 0x00 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
group.long 0x4a4++0x27
|
|
line.long 0x0 "SW_PAD_CTL_PAD_RAS,SW_PAD_CTL Generic (RAS)"
|
|
bitfld.long 0x0 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x4 "SW_PAD_CTL_PAD_CAS,SW_PAD_CTL Generic (CAS)"
|
|
bitfld.long 0x4 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x8 "SW_PAD_CTL_PAD_SDWE,SW_PAD_CTL Generic (SDWE)"
|
|
bitfld.long 0x8 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0xC "SW_PAD_CTL_PAD_SDCKE0,SW_PAD_CTL Generic (SDCKE0)"
|
|
bitfld.long 0xC 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x10 "SW_PAD_CTL_PAD_SDCKE1,SW_PAD_CTL Generic (SDCKE1)"
|
|
bitfld.long 0x10 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x14 "SW_PAD_CTL_PAD_SDCLK,SW_PAD_CTL Generic (SDCLK)"
|
|
bitfld.long 0x14 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x18 "SW_PAD_CTL_PAD_SDQS0,SW_PAD_CTL Generic (SDQS0)"
|
|
bitfld.long 0x18 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x1C "SW_PAD_CTL_PAD_SDQS1,SW_PAD_CTL Generic (SDQS1)"
|
|
bitfld.long 0x1C 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x20 "SW_PAD_CTL_PAD_SDQS2,SW_PAD_CTL Generic (SDQS2)"
|
|
bitfld.long 0x20 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x20 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
line.long 0x24 "SW_PAD_CTL_PAD_SDQS3,SW_PAD_CTL Generic (SDQS3)"
|
|
bitfld.long 0x24 7. " PKE ,Pull/Keep Enable" "Disabled,Enabled"
|
|
bitfld.long 0x24 1.--2. " DSE ,Drive Strength Control" "Nominal,High,Max,?..."
|
|
tree.end
|
|
width 6.
|
|
tree "IOMUC Registers"
|
|
group.long 0x00++0x03
|
|
line.long 0x00 "GPRA,General Purpose Register Usage"
|
|
bitfld.long 0x00 2. " TAMPERDETECT ,Tamper detect logic enable bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " SDCTL_CSD1_SEL_B ,Chip-Select bit for SDCTL over WEIM (sdctl_csd1_sel_b)" "SDCTL,WEIM"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SDCTL_CSD0_SEL_B ,Chip-Select bit for SDCTL over WEIM (sdctl_csd0_sel_b)" "SDCTL,WEIM"
|
|
width 29.
|
|
group.long 0x794++0x13
|
|
line.long 0x0 "SW_PAD_CTL_GRP_DDRTYPE_GRP4,DDR_TYPE Group 4 Control Register"
|
|
bitfld.long 0x0 11.--12. " DDR_TYPE ,DDR_TYPE Field" "Mobile DDR,3.3v SDRAM,DDR2,?..."
|
|
line.long 0x4 "SW_PAD_CTL_GRP_DDRTYPE_GRP5,DDR_TYPE Group 5 Control Register"
|
|
bitfld.long 0x4 11.--12. " DDR_TYPE ,DDR_TYPE Field" "Mobile DDR,3.3v SDRAM,DDR2,?..."
|
|
line.long 0x8 "SW_PAD_CTL_GRP_DDRTYPE_GRP1,DDR_TYPE Group 1 Control Register"
|
|
bitfld.long 0x8 11.--12. " DDR_TYPE ,DDR_TYPE Field" "Mobile DDR,3.3v SDRAM,DDR2,?..."
|
|
line.long 0xC "SW_PAD_CTL_GRP_DDRTYPE_GRP2,DDR_TYPE Group 2 Control Register"
|
|
bitfld.long 0xC 11.--12. " DDR_TYPE ,DDR_TYPE Field" "Mobile DDR,3.3v SDRAM,DDR2,?..."
|
|
line.long 0x10 "SW_PAD_CTL_GRP_DDRTYPE_GRP3,DDR_TYPE Group 3 Control Register"
|
|
bitfld.long 0x10 11.--12. " DDR_TYPE ,DDR_TYPE Field" "Mobile DDR,3.3v SDRAM,DDR2,?..."
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree "AVIC (ARM1136JF-S Interrupt Controller)"
|
|
base ad:0x68000000
|
|
width 15.
|
|
if (((d.l(ad:0x68000000))&0x1000000)==0x00)
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "INTCNTL,Interrupt Control Register"
|
|
bitfld.long 0x00 25. " ABFLAG ,Core Arbitration Prioritization Risen Flag" "No effect,Rising"
|
|
bitfld.long 0x00 24. " ABFEN ,ABFLAG Sticky Enable" "Normal,Sticky"
|
|
textline " "
|
|
bitfld.long 0x00 22. " NIDIS ,Normal Interrupt Disable" "No,Yes"
|
|
bitfld.long 0x00 21. " FIDIS ,Fast Interrupt Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 20. " NIAD ,Normal Interrupt Arbiter Rise ARM Level" "Disregarded,Increased"
|
|
bitfld.long 0x00 19. " FIAD ,Fast Interrupt Arbiter Rise ARM Level" "Disregarded,Increased"
|
|
textline " "
|
|
bitfld.long 0x00 18. " NM ,Normal Interrupt Mode Control" "Not accelerated,Accelerated"
|
|
else
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "INTCNTL,Interrupt Control Register"
|
|
eventfld.long 0x00 25. " ABFLAG ,Core Arbitration Prioritization Risen Flag" "No effect,Rising"
|
|
bitfld.long 0x00 24. " ABFEN ,ABFLAG Sticky Enable" "Normal,Sticky"
|
|
textline " "
|
|
bitfld.long 0x00 22. " NIDIS ,Normal Interrupt Disable" "No,Yes"
|
|
bitfld.long 0x00 21. " FIDIS ,Fast Interrupt Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 20. " NIAD ,Normal Interrupt Arbiter Rise ARM Level" "Disregarded,Increased"
|
|
bitfld.long 0x00 19. " FIAD ,Fast Interrupt Arbiter Rise ARM Level" "Disregarded,Increased"
|
|
textline " "
|
|
bitfld.long 0x00 18. " NM ,Normal Interrupt Mode Control" "Not accelerated,Accelerated"
|
|
endif
|
|
group.long 0x04++0x3b
|
|
line.long 0x00 "NIMASK,Normal Interrupt Mask Register"
|
|
bitfld.long 0x00 0.--4. " NIMASK ,Normal Interrupt Mask" "Level 0 disabled,<= level 1 disabled,<= level 2 disabled,<= level 3 disabled,<= level 4 disabled,<= level 5 disabled,<= level 6 disabled,<= level 7 disabled,<= level 8 disabled,<= level 9 disabled,<= level 10 disabled,<= level 11 disabled,<= level 12 disabled,<= level 13 disabled,<= level 14 disabled,All disabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled,All enabled"
|
|
line.long 0x04 "INTENNUM,Interrupt Enable Number Register"
|
|
bitfld.long 0x04 0.--5. " ENNUM ,Interrupt Enable Number" "Source 0,Source 1,Source 2,Source 3,Source 4,Source 5,Source 6,Source 7,Source 8,Source 9,Source 10,Source 11,Source 12,Source 13,Source 14,Source 15,Source 16,Source 17,Source 18,Source 19,Source 20,Source 21,Source 22,Source 23,Source 24,Source 25,Source 26,Source 27,Source 28,Source 29,Source 30,Source 31,Source 32,Source 33,Source 34,Source 35,Source 36,Source 37,Source 38,Source 39,Source 40,Source 41,Source 42,Source 43,Source 44,Source 45,Source 46,Source 47,Source 48,Source 49,Source 50,Source 51,Source 52,Source 53,Source 54,Source 55,Source 56,Source 57,Source 58,Source 59,Source 60,Source 61,Source 62,Source 63"
|
|
line.long 0x08 "INTDISNUM,Interrupt Disable Number Register"
|
|
bitfld.long 0x08 0.--5. " DISNUM ,Interrupt Disable Number" "Source 0,Source 1,Source 2,Source 3,Source 4,Source 5,Source 6,Source 7,Source 8,Source 9,Source 10,Source 11,Source 12,Source 13,Source 14,Source 15,Source 16,Source 17,Source 18,Source 19,Source 20,Source 21,Source 22,Source 23,Source 24,Source 25,Source 26,Source 27,Source 28,Source 29,Source 30,Source 31,Source 32,Source 33,Source 34,Source 35,Source 36,Source 37,Source 38,Source 39,Source 40,Source 41,Source 42,Source 43,Source 44,Source 45,Source 46,Source 47,Source 48,Source 49,Source 50,Source 51,Source 52,Source 53,Source 54,Source 55,Source 56,Source 57,Source 58,Source 59,Source 60,Source 61,Source 62,Source 63"
|
|
line.long 0x0c "INTENABLEH,Interrupt Enable Register High"
|
|
bitfld.long 0x0c 31. " INTENABLE63 ,EXT_INT0 Interrupt 63 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 30. " INTENABLE62 ,EXT_INT1 Interrupt 62 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 29. " INTENABLE61 ,EXT_INT2 Interrupt 61 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 28. " INTENABLE60 ,EXT_INT3 Interrupt 60 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 27. " INTENABLE59 ,EXT_INT4 Interrupt 59 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 26. " INTENABLE58 ,EXT_INT5 Interrupt 58 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " INTENABLE57 ,FEC Interrupt 57 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 24. " INTENABLE56 ,GPIO-3 Interrupt 56 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 23. " INTENABLE55 ,WDOG Interrupt 55 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 20. " INTENABLE52 ,GPIO-1 Interrupt 52 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " INTENABLE51 ,GPIO-2 Interrupt 51 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 18. " INTENABLE50 ,SCC SMN Interrupt 50 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 17. " INTENABLE49 ,SCC SCM Interrupt 49 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 16. " INTENABLE48 ,ARM ECT0/ECT1 Interrupt 48 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 15. " INTENABLE47 ,SPDIF Interrupt 47 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 14. " INTENABLE46 ,MLB Interrupt 46 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " INTENABLE45 ,UART-1 Interrupt 45 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 12. " INTENABLE44 ,CAN-2 Interrupt 44 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 11. " INTENABLE43 ,CAN-1 Interrupt 43 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 10. " INTENABLE42 ,IPU Func Interrupt 42 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 9. " INTENABLE41 ,IPU Error Interrupt 41 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 8. " INTENABLE40 ,ESAI Interrupt 40 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " INTENABLE39 ,MSHC Interrupt 39 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 5. " INTENABLE37 ,USB-OTG Interrupt 37 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 3. " INTENABLE35 ,USB-HS Interrupt 35 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 2. " INTENABLE34 ,SDMA Interrupt 34 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " INTENABLE33 ,NANDFC Interrupt 33 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 0. " INTENABLE32 ,UART2 Interrupt 32 Enable" "Disabled,Enabled"
|
|
line.long 0x10 "INTENABLEL,Interrupt Enable Register Low"
|
|
bitfld.long 0x10 31. " INTENABLE31 ,CCM Interrupt 31 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 30. " INTENABLE30 ,POWER FAIL Interrupt 30 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 29. " INTENABLE29 ,GPT Interrupt 29 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 28. " INTENABLE28 ,EPIT-1 Interrupt 28 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 27. " INTENABLE27 ,EPIT-2 Interrupt 27 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 26. " INTENABLE26 ,PWM Interrupt 26 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 25. " INTENABLE25 ,RTC Interrupt 25 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 24. " INTENABLE24 ,KPP Interrupt 24 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 23. " INTENABLE23 ,PMU/EVTMON Interrupt 23 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 22. " INTENABLE22 ,RNGC Interrupt 22 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 19. " INTENABLE19 ,IIM Interrupt 19 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 18. " INTENABLE18 ,UART3 Interrupt 18 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 17. " INTENABLE17 ,ASRC Interrupt 17 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 16. " INTENABLE16 ,GPU2D Interrupt 16 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 15. " INTENABLE15 ,ATA Interrupt 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 14. " INTENABLE14 ,CSPI-1 Interrupt 14 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 13. " INTENABLE13 ,CSPI-2 Interrupt 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 12. " INTENABLE12 ,SSI-2 Interrupt 12 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 11. " INTENABLE11 ,SSI-1 Interrupt 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 10. " INTENABLE10 ,I2C-1 Interrupt 10 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 9. " INTENABLE9 ,ESDHC3 Interrupt 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 8. " INTENABLE8 ,ESDHC2 Interrupt 8 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " INTENABLE7 ,ESDHC-1 Interrupt 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 6. " INTENABLE6 ,RTIC Interrupt 6 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 4. " INTENABLE4 ,I2C-2 Interrupt 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 3. " INTENABLE3 ,I2C-3 Interrupt 3 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 2. " INTENABLE2 ,OWIRE Interrupt 2 Enable" "Disabled,Enabled"
|
|
line.long 0x14 "INTTYPEH,Interrupt Type Register High"
|
|
bitfld.long 0x14 31. " INTTYPE63 ,EXT_INT0 Interrupt 63 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 30. " INTTYPE62 ,EXT_INT1 Interrupt 62 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 29. " INTTYPE61 ,EXT_INT2 Interrupt 61 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 28. " INTTYPE60 ,EXT_INT3 Interrupt 60 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 27. " INTTYPE59 ,EXT_INT4 EXT_INT4 Interrupt 59 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 26. " INTTYPE58 ,EXT_INT5 Interrupt 58 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 25. " INTTYPE57 ,FEC Interrupt 57 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 24. " INTTYPE56 ,GPIO-3 Interrupt 56 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 23. " INTTYPE55 ,WDOG Interrupt 55 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 20. " INTTYPE52 ,GPIO-1 Interrupt 52 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 19. " INTTYPE51 ,GPIO-2 Interrupt 51 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 18. " INTTYPE50 ,SCC SMN Interrupt 50 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 17. " INTTYPE49 ,SCC SCM Interrupt 49 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 16. " INTTYPE48 ,ARM ECT0/ECT1 Interrupt 48 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 15. " INTTYPE47 ,SPDIF Interrupt 47 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 14. " INTTYPE46 ,MLB Interrupt 46 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 13. " INTTYPE45 ,UART-1 Interrupt 45 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 12. " INTTYPE44 ,CAN-2 Interrupt 44 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 11. " INTTYPE43 ,CAN-1 Interrupt 43 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 10. " INTTYPE42 ,IPU Func Interrupt 42 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 9. " INTTYPE41 ,IPU Error Interrupt 41 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 8. " INTTYPE40 ,ESAI Interrupt 40 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 7. " INTTYPE39 ,MSHC Interrupt 39 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 5. " INTTYPE37 ,USB-OTG Interrupt 37 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 3. " INTTYPE35 ,USB-HS Interrupt 35 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 2. " INTTYPE34 ,SDMA Interrupt 34 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x14 1. " INTTYPE33 ,NANDFC Interrupt 33 Type" "IRQ,FIQ"
|
|
bitfld.long 0x14 0. " INTTYPE32 ,UART2 Interrupt 32 Type" "IRQ,FIQ"
|
|
line.long 0x18 "INTTYPEL,Interrupt Type Register Low"
|
|
bitfld.long 0x18 31. " INTTYPE31 ,CCM Interrupt 31 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 30. " INTTYPE30 ,POWER FAIL Interrupt 30 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 29. " INTTYPE29 ,GPT Interrupt 29 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 28. " INTTYPE28 ,EPIT-1 Interrupt 28 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 27. " INTTYPE27 ,EPIT-2 Interrupt 27 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 26. " INTTYPE26 ,PWM Interrupt 26 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 25. " INTTYPE25 ,RTC Interrupt 25 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 24. " INTTYPE24 ,KPP Interrupt 24 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 23. " INTTYPE23 ,PMU/EVTMON Interrupt 23 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 22. " INTTYPE22 ,RNGC Interrupt 22 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 19. " INTTYPE19 ,IIM Interrupt 19 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 18. " INTTYPE18 ,UART3 Interrupt 18 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 17. " INTTYPE17 ,ASRC Interrupt 17 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 16. " INTTYPE16 ,GPU2D Interrupt 16 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 15. " INTTYPE15 ,ATA Interrupt 15 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 14. " INTTYPE14 ,CSPI-1 Interrupt 14 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 13. " INTTYPE13 ,CSPI-2 Interrupt 13 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 12. " INTTYPE12 ,SSI-2 Interrupt 12 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 11. " INTTYPE11 ,SSI-1 Interrupt 11 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 10. " INTTYPE10 ,I2C-1 Interrupt 10 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 9. " INTTYPE9 ,ESDHC3 Interrupt 9 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 8. " INTTYPE8 ,ESDHC2 Interrupt 8 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 7. " INTTYPE7 ,ESDHC-1 Interrupt 7 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 6. " INTTYPE6 ,RTIC Interrupt 6 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 4. " INTTYPE4 ,I2C-2 Interrupt 4 Type" "IRQ,FIQ"
|
|
bitfld.long 0x18 3. " INTTYPE3 ,I2C-3 Interrupt 3 Type" "IRQ,FIQ"
|
|
textline " "
|
|
bitfld.long 0x18 2. " INTTYPE2 ,OWIRE Interrupt 2 Type" "IRQ,FIQ"
|
|
line.long 0x1c "NIPRIORITY7,Normal Interrupt Priority Level Register 7"
|
|
bitfld.long 0x1c 28.--31. " NIPR63 ,Normal Interrupt 63 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x1c 24.--27. " NIPR62 ,Normal Interrupt 62 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x1c 20.--23. " NIPR61 ,Normal Interrupt 61 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x1c 16.--19. " NIPR60 ,Normal Interrupt 60 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x1c 12.--15. " NIPR59 ,Normal Interrupt 59 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x1c 8.--11. " NIPR58 ,Normal Interrupt 58 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x1c 4.--7. " NIPR57 ,Normal Interrupt 57 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x1c 0.--3. " NIPR56 ,Normal Interrupt 56 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x20 "NIPRIORITY6,Normal Interrupt Priority Level Register 6"
|
|
bitfld.long 0x20 28.--31. " NIPR55 ,Normal Interrupt 55 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x20 16.--19. " NIPR52 ,Normal Interrupt 52 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x20 12.--15. " NIPR51 ,Normal Interrupt 51 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x20 8.--11. " NIPR50 ,Normal Interrupt 50 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x20 4.--7. " NIPR49 ,Normal Interrupt 49 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x20 0.--3. " NIPR48 ,Normal Interrupt 48 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x24 "NIPRIORITY5,Normal Interrupt Priority Level Register 5"
|
|
bitfld.long 0x24 28.--31. " NIPR47 ,Normal Interrupt 47 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x24 24.--27. " NIPR46 ,Normal Interrupt 46 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x24 20.--23. " NIPR45 ,Normal Interrupt 45 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x24 16.--19. " NIPR44 ,Normal Interrupt 44 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x24 12.--15. " NIPR43 ,Normal Interrupt 43 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x24 8.--11. " NIPR42 ,Normal Interrupt 42 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x24 4.--7. " NIPR41 ,Normal Interrupt 41 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x24 0.--3. " NIPR40 ,Normal Interrupt 40 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x28 "NIPRIORITY4,Normal Interrupt Priority Level Register 4"
|
|
bitfld.long 0x28 28.--31. " NIPR39 ,Normal Interrupt 39 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x28 20.--23. " NIPR37 ,Normal Interrupt 37 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x28 12.--15. " NIPR35 ,Normal Interrupt 35 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x28 8.--11. " NIPR34 ,Normal Interrupt 34 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x28 4.--7. " NIPR33 ,Normal Interrupt 33 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x28 0.--3. " NIPR32 ,Normal Interrupt 32 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x2c "NIPRIORITY3,Normal Interrupt Priority Level Register 3"
|
|
bitfld.long 0x2c 28.--31. " NIPR31 ,Normal Interrupt 31 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x2c 24.--27. " NIPR30 ,Normal Interrupt 30 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x2c 20.--23. " NIPR29 ,Normal Interrupt 29 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x2c 16.--19. " NIPR28 ,Normal Interrupt 28 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x2c 12.--15. " NIPR27 ,Normal Interrupt 27 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x2c 8.--11. " NIPR26 ,Normal Interrupt 26 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x2c 4.--7. " NIPR25 ,Normal Interrupt 25 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x2c 0.--3. " NIPR24 ,Normal Interrupt 24 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x30 "NIPRIORITY2,Normal Interrupt Priority Level Register 2"
|
|
bitfld.long 0x30 28.--31. " NIPR23 ,Normal Interrupt 23 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x30 24.--27. " NIPR22 ,Normal Interrupt 22 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x30 12.--15. " NIPR19 ,Normal Interrupt 19 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x30 8.--11. " NIPR18 ,Normal Interrupt 18 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x30 4.--7. " NIPR17 ,Normal Interrupt 17 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x30 0.--3. " NIPR16 ,Normal Interrupt 16 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x34 "NIPRIORITY1,Normal Interrupt Priority Level Register 1"
|
|
bitfld.long 0x34 28.--31. " NIPR15 ,Normal Interrupt 15 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x34 24.--27. " NIPR14 ,Normal Interrupt 14 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x34 20.--23. " NIPR13 ,Normal Interrupt 13 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x34 16.--19. " NIPR12 ,Normal Interrupt 12 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x34 12.--15. " NIPR11 ,Normal Interrupt 11 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x34 8.--11. " NIPR10 ,Normal Interrupt 10 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x34 4.--7. " NIPR9 ,Normal Interrupt 9 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x34 0.--3. " NIPR8 ,Normal Interrupt 8 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
line.long 0x38 "NIPRIORITY0,Normal Interrupt Priority Level Register 0"
|
|
bitfld.long 0x38 28.--31. " NIPR7 ,Normal Interrupt 7 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x38 24.--27. " NIPR6 ,Normal Interrupt 6 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x38 16.--19. " NIPR4 ,Normal Interrupt 4 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
bitfld.long 0x38 12.--15. " NIPR3 ,Normal Interrupt 3 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
textline " "
|
|
bitfld.long 0x38 8.--11. " NIPR2 ,Normal Interrupt 2 Priority Level" "Lowest,1,2,3,4,5,6,7,8,9,10,11,12,13,14,Highest"
|
|
rgroup.long 0x40++0xf
|
|
line.long 0x00 "NIVECSR,Normal Interrupt Vector and Status Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " NIVECTOR ,Normal Interrupt Vector"
|
|
hexmask.long.word 0x00 0.--15. 1. " NIPRILVL ,Normal Interrupt Priority Level"
|
|
line.long 0x04 "FIVECSR,Fast Interrupt Vector and Status Register"
|
|
line.long 0x08 "INTSRCH,Interrupt Source Register High"
|
|
bitfld.long 0x08 31. " INTIN63 ,EXT_INT0 Interrupt 63 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 30. " INTIN62 ,EXT_INT1 Interrupt 62 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 29. " INTIN61 ,EXT_INT2 Interrupt 61 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 28. " INTIN60 ,EXT_INT3 Interrupt 60 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 27. " INTIN59 ,EXT_INT4 Interrupt 59 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 26. " INTIN58 ,EXT_INT5 Interrupt 58 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 25. " INTIN57 ,FEC Interrupt 57 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 24. " INTIN56 ,GPIO-3 Interrupt 56 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 23. " INTIN55 ,WDOG Interrupt 55 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 20. " INTIN52 ,GPIO-1 Interrupt 52 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 19. " INTIN51 ,GPIO-2 Interrupt 51 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 18. " INTIN50 ,SCC SMN Interrupt 50 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 17. " INTIN49 ,SCC SCM Interrupt 49 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 16. " INTIN48 ,ARM ECT0/ECT1 Interrupt 48 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 15. " INTIN47 ,SPDIF Interrupt 47 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 14. " INTIN46 ,MLB Interrupt 46 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 13. " INTIN45 ,UART-1 Interrupt 45 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 12. " INTIN44 ,CAN-2 Interrupt 44 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 11. " INTIN43 ,CAN-1 Interrupt 43 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 10. " INTIN42 ,IPU Func Interrupt 42 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 9. " INTIN41 ,IPU Error Interrupt 41 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 8. " INTIN40 ,ESAI Interrupt 40 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 7. " INTIN39 ,MSHC Interrupt 39 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 5. " INTIN37 ,USB-OTG Interrupt 37 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 3. " INTIN35 ,USB-HS Interrupt 35 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 2. " INTIN34 ,SDMA Interrupt 34 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x08 1. " INTIN33 ,NANDFC Interrupt 33 Source" "Negated,Asserted"
|
|
bitfld.long 0x08 0. " INTIN32 ,UART2 Interrupt 32 Source" "Negated,Asserted"
|
|
line.long 0x0c "INTSRCL,Interrupt Source Register Low"
|
|
bitfld.long 0x0c 31. " INTIN31 ,CCM Interrupt 31 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 30. " INTIN30 ,POWER FAIL Interrupt 30 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 29. " INTIN29 ,GPT Interrupt 29 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 28. " INTIN28 ,EPIT-1 Interrupt 28 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 27. " INTIN27 ,EPIT-2 Interrupt 27 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 26. " INTIN26 ,PWM Interrupt 26 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " INTIN25 ,RTC Interrupt 25 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 24. " INTIN24 ,KPP Interrupt 24 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 23. " INTIN23 ,PMU/EVTMON Interrupt 23 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 22. " INTIN22 ,RNGC Interrupt 22 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " INTIN19 ,IIM Interrupt 19 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 18. " INTIN18 ,UART3 Interrupt 18 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 17. " INTIN17 ,ASRC Interrupt 17 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 16. " INTIN16 ,GPU2D Interrupt 16 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 15. " INTIN15 ,ATA Interrupt 15 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 14. " INTIN14 ,CSPI-1 Interrupt 14 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " INTIN13 ,CSPI-2 Interrupt 13 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 12. " INTIN12 ,SSI-2 Interrupt 12 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 11. " INTIN11 ,SSI-1 Interrupt 11 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 10. " INTIN10 ,I2C-1 Interrupt 10 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 9. " INTIN9 ,ESDHC3 Interrupt 9 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 8. " INTIN8 ,ESDHC2 Interrupt 8 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " INTIN7 ,ESDHC-1 Interrupt 7 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 6. " INTIN6 ,RTIC Interrupt 6 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 4. " INTIN4 ,I2C-2 Interrupt 4 Source" "Negated,Asserted"
|
|
bitfld.long 0x0c 3. " INTIN3 ,I2C-3 Interrupt 3 Source" "Negated,Asserted"
|
|
textline " "
|
|
bitfld.long 0x0c 2. " INTIN2 ,OWIRE Interrupt 2 Source" "Negated,Asserted"
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "INTFRCH,Interrupt Force Register High"
|
|
bitfld.long 0x00 31. " FORCE63 ,EXT_INT0 Interrupt 63 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 30. " FORCE62 ,EXT_INT1 Interrupt 62 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 29. " FORCE61 ,EXT_INT2 Interrupt 61 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 28. " FORCE60 ,EXT_INT3 Interrupt 60 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 27. " FORCE59 ,EXT_INT4 Interrupt 59 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 26. " FORCE58 ,EXT_INT5 Interrupt 58 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 25. " FORCE57 ,FEC Interrupt 57 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 24. " FORCE56 ,GPIO-3 Interrupt 56 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 23. " FORCE55 ,WDOG Interrupt 55 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 20. " FORCE52 ,GPIO-1 Interrupt 52 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 19. " FORCE51 ,GPIO-2 Interrupt 51 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 18. " FORCE50 ,SCC SMN Interrupt 50 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 17. " FORCE49 ,SCC SCM Interrupt 49 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 16. " FORCE48 ,ARM ECT0/ECT1 Interrupt 48 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FORCE47 ,SPDIF Interrupt 47 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 14. " FORCE46 ,MLB Interrupt 46 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 13. " FORCE45 ,UART-1 Interrupt 45 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 12. " FORCE44 ,CAN-2 Interrupt 44 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FORCE43 ,CAN-1 Interrupt 43 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 10. " FORCE42 ,IPU Func Interrupt 42 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 9. " FORCE41 ,IPU Error Interrupt 41 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 8. " FORCE40 ,ESAI Interrupt 40 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 7. " FORCE39 ,MSHC Interrupt 39 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 5. " FORCE37 ,USB-OTG Interrupt 37 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 3. " FORCE35 ,USB-HS Interrupt 35 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 2. " FORCE34 ,SDMA Interrupt 34 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 1. " FORCE33 ,NANDFC Interrupt 33 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x00 0. " FORCE32 ,UART2 Interrupt 32 Source Force Request" "Standard,Forced"
|
|
line.long 0x04 "INTFRCL,Interrupt Force Register Low"
|
|
bitfld.long 0x04 31. " FORCE31 ,CCM Interrupt 31 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 30. " FORCE30 ,POWER FAIL Interrupt 30 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 29. " FORCE29 ,GPT Interrupt 29 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 28. " FORCE28 ,EPIT-1 Interrupt 28 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 27. " FORCE27 ,EPIT-2 Interrupt 27 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 26. " FORCE26 ,PWM Interrupt 26 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 25. " FORCE25 ,RTC Interrupt 25 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 24. " FORCE24 ,KPP Interrupt 24 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 23. " FORCE23 ,PMU/EVTMON Interrupt 23 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 22. " FORCE22 ,RNGC Interrupt 22 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 19. " FORCE19 ,IIM Interrupt 19 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 18. " FORCE18 ,UART3 Interrupt 18 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 17. " FORCE17 ,ASRC Interrupt 17 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 16. " FORCE16 ,GPU2D Interrupt 16 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 15. " FORCE15 ,ATA Interrupt 15 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 14. " FORCE14 ,CSPI-1 Interrupt 14 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 13. " FORCE13 ,CSPI-2 Interrupt 13 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 12. " FORCE12 ,SSI-2 Interrupt 12 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 11. " FORCE11 ,SSI-1 Interrupt 11 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 10. " FORCE10 ,I2C-1 Interrupt 10 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 9. " FORCE9 ,ESDHC3 Interrupt 9 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 8. " FORCE8 ,ESDHC2 Interrupt 8 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 7. " FORCE7 ,ESDHC-1 Interrupt 7 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 6. " FORCE6 ,RTIC Interrupt 6 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 4. " FORCE4 ,I2C-2 Interrupt 4 Source Force Request" "Standard,Forced"
|
|
bitfld.long 0x04 3. " FORCE3 ,I2C-3 Interrupt 3 Source Force Request" "Standard,Forced"
|
|
textline " "
|
|
bitfld.long 0x04 2. " FORCE2 ,OWIRE Interrupt 2 Source Force Request" "Standard,Forced"
|
|
rgroup.long 0x58++0xf
|
|
line.long 0x00 "NIPNDH,Normal Interrupt Pending Register High"
|
|
bitfld.long 0x00 31. " NIPEND63 ,EXT_INT0 Normal Interrupt 63 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 30. " NIPEND62 ,EXT_INT1 Normal Interrupt 62 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 29. " NIPEND61 ,EXT_INT2 Normal Interrupt 61 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 28. " NIPEND60 ,EXT_INT3 Normal Interrupt 60 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 27. " NIPEND59 ,EXT_INT4 Normal Interrupt 59 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 26. " NIPEND58 ,EXT_INT5 Normal Interrupt 58 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 25. " NIPEND57 ,FEC Normal Interrupt 57 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 24. " NIPEND56 ,GPIO-3 Normal Interrupt 56 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 23. " NIPEND55 ,WDOG Normal Interrupt 55 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 20. " NIPEND52 ,GPIO-1 Normal Interrupt 52 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 19. " NIPEND51 ,GPIO-2 Normal Interrupt 51 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 18. " NIPEND50 ,SCC SMN Normal Interrupt 50 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 17. " NIPEND49 ,SCC SCM Normal Interrupt 49 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 16. " NIPEND48 ,ARM ECT0/ECT1 Normal Interrupt 48 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 15. " NIPEND47 ,SPDIF Normal Interrupt 47 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 14. " NIPEND46 ,MLB Normal Interrupt 46 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 13. " NIPEND45 ,UART-1 Normal Interrupt 45 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 12. " NIPEND44 ,CAN-2 Normal Interrupt 44 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 11. " NIPEND43 ,CAN-1 Normal Interrupt 43 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 10. " NIPEND42 ,IPU Func Normal Interrupt 42 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 9. " NIPEND41 ,IPU Error Normal Interrupt 41 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 8. " NIPEND40 ,ESAI Normal Interrupt 40 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 7. " NIPEND39 ,MSHC Normal Interrupt 39 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 5. " NIPEND37 ,USB-OTG Normal Interrupt 37 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 3. " NIPEND35 ,USB-HS Normal Interrupt 35 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 2. " NIPEND34 ,SDMA Normal Interrupt 34 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 1. " NIPEND33 ,NANDFC Normal Interrupt 33 Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 0. " NIPEND32 ,UART2 Normal Interrupt 32 Pending" "Not pending,Pending"
|
|
line.long 0x04 "NIPNDL,Normal Interrupt Pending Register Low"
|
|
bitfld.long 0x04 31. " NIPEND31 ,CCM Normal Interrupt 31 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 30. " NIPEND30 ,POWER FAIL Normal Interrupt 30 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 29. " NIPEND29 ,GPT Normal Interrupt 29 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 28. " NIPEND28 ,EPIT-1 Normal Interrupt 28 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 27. " NIPEND27 ,EPIT-2 Normal Interrupt 27 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 26. " NIPEND26 ,PWM Normal Interrupt 26 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 25. " NIPEND25 ,RTC Normal Interrupt 25 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 24. " NIPEND24 ,KPP Normal Interrupt 24 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 23. " NIPEND23 ,PMU/EVTMON Normal Interrupt 23 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 22. " NIPEND22 ,RNGC Normal Interrupt 22 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 19. " NIPEND19 ,IIM Normal Interrupt 19 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 18. " NIPEND18 ,UART3 Normal Interrupt 18 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 17. " NIPEND17 ,ASRC Normal Interrupt 17 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 16. " NIPEND16 ,GPU2D Normal Interrupt 16 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 15. " NIPEND15 ,ATA Normal Interrupt 15 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 14. " NIPEND14 ,CSPI-1 Normal Interrupt 14 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 13. " NIPEND13 ,CSPI-2 Normal Interrupt 13 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 12. " NIPEND12 ,SSI-2 Normal Interrupt 12 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 11. " NIPEND11 ,SSI-1 Normal Interrupt 11 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 10. " NIPEND10 ,I2C-1 Normal Interrupt 10 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 9. " NIPEND9 ,ESDHC3 Normal Interrupt 9 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 8. " NIPEND8 ,ESDHC2 Normal Interrupt 8 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 7. " NIPEND7 ,ESDHC-1 Normal Interrupt 7 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 6. " NIPEND6 ,RTIC Normal Interrupt 6 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 4. " NIPEND4 ,I2C-2 Normal Interrupt 4 Pending" "Not pending,Pending"
|
|
bitfld.long 0x04 3. " NIPEND3 ,I2C-3 Normal Interrupt 3 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 2. " NIPEND2 ,OWIRE Normal Interrupt 2 Pending" "Not pending,Pending"
|
|
line.long 0x08 "FIPNDH,Fast Interrupt Pending Register High"
|
|
bitfld.long 0x08 31. " FIPEND63 ,EXT_INT0 Fast Interrupt 63 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 30. " FIPEND62 ,EXT_INT1 Fast Interrupt 62 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 29. " FIPEND61 ,EXT_INT2 Fast Interrupt 61 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 28. " FIPEND60 ,EXT_INT3 Fast Interrupt 60 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 27. " FIPEND59 ,EXT_INT4 Fast Interrupt 59 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 26. " FIPEND58 ,EXT_INT5 Fast Interrupt 58 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 25. " FIPEND57 ,FEC Fast Interrupt 57 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 24. " FIPEND56 ,GPIO-3 Fast Interrupt 56 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 23. " FIPEND55 ,WDOG Fast Interrupt 55 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 20. " FIPEND52 ,GPIO-1 Fast Interrupt 52 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 19. " FIPEND51 ,GPIO-2 Fast Interrupt 51 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 18. " FIPEND50 ,SCC SMN Fast Interrupt 50 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 17. " FIPEND49 ,SCC SCM Fast Interrupt 49 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 16. " FIPEND48 ,ARM ECT0/ECT1 Fast Interrupt 48 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 15. " FIPEND47 ,SPDIF Fast Interrupt 47 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 14. " FIPEND46 ,MLB Fast Interrupt 46 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 13. " FIPEND45 ,UART-1 Fast Interrupt 45 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 12. " FIPEND44 ,CAN-2 Fast Interrupt 44 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 11. " FIPEND43 ,CAN-1 Fast Interrupt 43 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 10. " FIPEND42 ,IPU Func Fast Interrupt 42 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 9. " FIPEND41 ,IPU Error Fast Interrupt 41 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 8. " FIPEND40 ,ESAI Fast Interrupt 40 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 7. " FIPEND39 ,MSHC Fast Interrupt 39 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 5. " FIPEND37 ,USB-OTG Fast Interrupt 37 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 3. " FIPEND35 ,USB-HS Fast Interrupt 35 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 2. " FIPEND34 ,SDMA Fast Interrupt 34 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x08 1. " FIPEND33 ,NANDFC Fast Interrupt 33 Pending" "Not pending,Pending"
|
|
bitfld.long 0x08 0. " FIPEND32 ,UART2 Fast Interrupt 32 Pending" "Not pending,Pending"
|
|
line.long 0x0c "FIPNDL,Fast Interrupt Pending Register Low"
|
|
bitfld.long 0x0c 31. " FIPEND31 ,CCM Fast Interrupt 31 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 30. " FIPEND30 ,POWER FAIL Fast Interrupt 30 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 29. " FIPEND29 ,GPT Fast Interrupt 29 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 28. " FIPEND28 ,EPIT-1 Fast Interrupt 28 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 27. " FIPEND27 ,EPIT-2 Fast Interrupt 27 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 26. " FIPEND26 ,PWM Fast Interrupt 26 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " FIPEND25 ,RTC Fast Interrupt 25 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 24. " FIPEND24 ,KPP Fast Interrupt 24 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 23. " FIPEND23 ,PMU/EVTMON Fast Interrupt 23 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 22. " FIPEND22 ,RNGC Fast Interrupt 22 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " FIPEND19 ,IIM Fast Interrupt 19 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 18. " FIPEND18 ,UART3 Fast Interrupt 18 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 17. " FIPEND17 ,ASRC Fast Interrupt 17 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 16. " FIPEND16 ,GPU2D Fast Interrupt 16 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 15. " FIPEND15 ,ATA Fast Interrupt 15 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 14. " FIPEND14 ,CSPI-1 Fast Interrupt 14 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " FIPEND13 ,CSPI-2 Fast Interrupt 13 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 12. " FIPEND12 ,SSI-2 Fast Interrupt 12 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 11. " FIPEND11 ,SSI-1 Fast Interrupt 11 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 10. " FIPEND10 ,I2C-1 Fast Interrupt 10 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 9. " FIPEND9 ,ESDHC3 Fast Interrupt 9 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 8. " FIPEND8 ,ESDHC2 Fast Interrupt 8 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " FIPEND7 ,ESDHC-1 Fast Interrupt 7 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 6. " FIPEND6 ,RTIC Fast Interrupt 6 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 4. " FIPEND4 ,I2C-2 Fast Interrupt 4 Pending" "Not pending,Pending"
|
|
bitfld.long 0x0c 3. " FIPEND3 ,I2C-3 Fast Interrupt 3 Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x0c 2. " FIPEND2 ,OWIRE Fast Interrupt 2 Pending" "Not pending,Pending"
|
|
group.long 0x100++0xff
|
|
line.long 0x0 "VECTOR0 ,AVIC Vector Register 0 "
|
|
hexmask.long 0x0 2.--31. 0x4 " VECTOR0 ,AVIC Vector"
|
|
line.long 0x4 "VECTOR1 ,AVIC Vector Register 1 "
|
|
hexmask.long 0x4 2.--31. 0x4 " VECTOR1 ,AVIC Vector"
|
|
line.long 0x8 "VECTOR2 ,AVIC Vector Register 2 "
|
|
hexmask.long 0x8 2.--31. 0x4 " VECTOR2 ,AVIC Vector"
|
|
line.long 0xC "VECTOR3 ,AVIC Vector Register 3 "
|
|
hexmask.long 0xC 2.--31. 0x4 " VECTOR3 ,AVIC Vector"
|
|
line.long 0x10 "VECTOR4 ,AVIC Vector Register 4 "
|
|
hexmask.long 0x10 2.--31. 0x4 " VECTOR4 ,AVIC Vector"
|
|
line.long 0x14 "VECTOR5 ,AVIC Vector Register 5 "
|
|
hexmask.long 0x14 2.--31. 0x4 " VECTOR5 ,AVIC Vector"
|
|
line.long 0x18 "VECTOR6 ,AVIC Vector Register 6 "
|
|
hexmask.long 0x18 2.--31. 0x4 " VECTOR6 ,AVIC Vector"
|
|
line.long 0x1C "VECTOR7 ,AVIC Vector Register 7 "
|
|
hexmask.long 0x1C 2.--31. 0x4 " VECTOR7 ,AVIC Vector"
|
|
line.long 0x20 "VECTOR8 ,AVIC Vector Register 8 "
|
|
hexmask.long 0x20 2.--31. 0x4 " VECTOR8 ,AVIC Vector"
|
|
line.long 0x24 "VECTOR9 ,AVIC Vector Register 9 "
|
|
hexmask.long 0x24 2.--31. 0x4 " VECTOR9 ,AVIC Vector"
|
|
line.long 0x28 "VECTOR10,AVIC Vector Register 10"
|
|
hexmask.long 0x28 2.--31. 0x4 " VECTOR10 ,AVIC Vector"
|
|
line.long 0x2C "VECTOR11,AVIC Vector Register 11"
|
|
hexmask.long 0x2C 2.--31. 0x4 " VECTOR11 ,AVIC Vector"
|
|
line.long 0x30 "VECTOR12,AVIC Vector Register 12"
|
|
hexmask.long 0x30 2.--31. 0x4 " VECTOR12 ,AVIC Vector"
|
|
line.long 0x34 "VECTOR13,AVIC Vector Register 13"
|
|
hexmask.long 0x34 2.--31. 0x4 " VECTOR13 ,AVIC Vector"
|
|
line.long 0x38 "VECTOR14,AVIC Vector Register 14"
|
|
hexmask.long 0x38 2.--31. 0x4 " VECTOR14 ,AVIC Vector"
|
|
line.long 0x3C "VECTOR15,AVIC Vector Register 15"
|
|
hexmask.long 0x3C 2.--31. 0x4 " VECTOR15 ,AVIC Vector"
|
|
line.long 0x40 "VECTOR16,AVIC Vector Register 16"
|
|
hexmask.long 0x40 2.--31. 0x4 " VECTOR16 ,AVIC Vector"
|
|
line.long 0x44 "VECTOR17,AVIC Vector Register 17"
|
|
hexmask.long 0x44 2.--31. 0x4 " VECTOR17 ,AVIC Vector"
|
|
line.long 0x48 "VECTOR18,AVIC Vector Register 18"
|
|
hexmask.long 0x48 2.--31. 0x4 " VECTOR18 ,AVIC Vector"
|
|
line.long 0x4C "VECTOR19,AVIC Vector Register 19"
|
|
hexmask.long 0x4C 2.--31. 0x4 " VECTOR19 ,AVIC Vector"
|
|
line.long 0x50 "VECTOR20,AVIC Vector Register 20"
|
|
hexmask.long 0x50 2.--31. 0x4 " VECTOR20 ,AVIC Vector"
|
|
line.long 0x54 "VECTOR21,AVIC Vector Register 21"
|
|
hexmask.long 0x54 2.--31. 0x4 " VECTOR21 ,AVIC Vector"
|
|
line.long 0x58 "VECTOR22,AVIC Vector Register 22"
|
|
hexmask.long 0x58 2.--31. 0x4 " VECTOR22 ,AVIC Vector"
|
|
line.long 0x5C "VECTOR23,AVIC Vector Register 23"
|
|
hexmask.long 0x5C 2.--31. 0x4 " VECTOR23 ,AVIC Vector"
|
|
line.long 0x60 "VECTOR24,AVIC Vector Register 24"
|
|
hexmask.long 0x60 2.--31. 0x4 " VECTOR24 ,AVIC Vector"
|
|
line.long 0x64 "VECTOR25,AVIC Vector Register 25"
|
|
hexmask.long 0x64 2.--31. 0x4 " VECTOR25 ,AVIC Vector"
|
|
line.long 0x68 "VECTOR26,AVIC Vector Register 26"
|
|
hexmask.long 0x68 2.--31. 0x4 " VECTOR26 ,AVIC Vector"
|
|
line.long 0x6C "VECTOR27,AVIC Vector Register 27"
|
|
hexmask.long 0x6C 2.--31. 0x4 " VECTOR27 ,AVIC Vector"
|
|
line.long 0x70 "VECTOR28,AVIC Vector Register 28"
|
|
hexmask.long 0x70 2.--31. 0x4 " VECTOR28 ,AVIC Vector"
|
|
line.long 0x74 "VECTOR29,AVIC Vector Register 29"
|
|
hexmask.long 0x74 2.--31. 0x4 " VECTOR29 ,AVIC Vector"
|
|
line.long 0x78 "VECTOR30,AVIC Vector Register 30"
|
|
hexmask.long 0x78 2.--31. 0x4 " VECTOR30 ,AVIC Vector"
|
|
line.long 0x7C "VECTOR31,AVIC Vector Register 31"
|
|
hexmask.long 0x7C 2.--31. 0x4 " VECTOR31 ,AVIC Vector"
|
|
line.long 0x80 "VECTOR32,AVIC Vector Register 32"
|
|
hexmask.long 0x80 2.--31. 0x4 " VECTOR32 ,AVIC Vector"
|
|
line.long 0x84 "VECTOR33,AVIC Vector Register 33"
|
|
hexmask.long 0x84 2.--31. 0x4 " VECTOR33 ,AVIC Vector"
|
|
line.long 0x88 "VECTOR34,AVIC Vector Register 34"
|
|
hexmask.long 0x88 2.--31. 0x4 " VECTOR34 ,AVIC Vector"
|
|
line.long 0x8C "VECTOR35,AVIC Vector Register 35"
|
|
hexmask.long 0x8C 2.--31. 0x4 " VECTOR35 ,AVIC Vector"
|
|
line.long 0x90 "VECTOR36,AVIC Vector Register 36"
|
|
hexmask.long 0x90 2.--31. 0x4 " VECTOR36 ,AVIC Vector"
|
|
line.long 0x94 "VECTOR37,AVIC Vector Register 37"
|
|
hexmask.long 0x94 2.--31. 0x4 " VECTOR37 ,AVIC Vector"
|
|
line.long 0x98 "VECTOR38,AVIC Vector Register 38"
|
|
hexmask.long 0x98 2.--31. 0x4 " VECTOR38 ,AVIC Vector"
|
|
line.long 0x9C "VECTOR39,AVIC Vector Register 39"
|
|
hexmask.long 0x9C 2.--31. 0x4 " VECTOR39 ,AVIC Vector"
|
|
line.long 0xA0 "VECTOR40,AVIC Vector Register 40"
|
|
hexmask.long 0xA0 2.--31. 0x4 " VECTOR40 ,AVIC Vector"
|
|
line.long 0xA4 "VECTOR41,AVIC Vector Register 41"
|
|
hexmask.long 0xA4 2.--31. 0x4 " VECTOR41 ,AVIC Vector"
|
|
line.long 0xA8 "VECTOR42,AVIC Vector Register 42"
|
|
hexmask.long 0xA8 2.--31. 0x4 " VECTOR42 ,AVIC Vector"
|
|
line.long 0xAC "VECTOR43,AVIC Vector Register 43"
|
|
hexmask.long 0xAC 2.--31. 0x4 " VECTOR43 ,AVIC Vector"
|
|
line.long 0xB0 "VECTOR44,AVIC Vector Register 44"
|
|
hexmask.long 0xB0 2.--31. 0x4 " VECTOR44 ,AVIC Vector"
|
|
line.long 0xB4 "VECTOR45,AVIC Vector Register 45"
|
|
hexmask.long 0xB4 2.--31. 0x4 " VECTOR45 ,AVIC Vector"
|
|
line.long 0xB8 "VECTOR46,AVIC Vector Register 46"
|
|
hexmask.long 0xB8 2.--31. 0x4 " VECTOR46 ,AVIC Vector"
|
|
line.long 0xBC "VECTOR47,AVIC Vector Register 47"
|
|
hexmask.long 0xBC 2.--31. 0x4 " VECTOR47 ,AVIC Vector"
|
|
line.long 0xC0 "VECTOR48,AVIC Vector Register 48"
|
|
hexmask.long 0xC0 2.--31. 0x4 " VECTOR48 ,AVIC Vector"
|
|
line.long 0xC4 "VECTOR49,AVIC Vector Register 49"
|
|
hexmask.long 0xC4 2.--31. 0x4 " VECTOR49 ,AVIC Vector"
|
|
line.long 0xC8 "VECTOR50,AVIC Vector Register 50"
|
|
hexmask.long 0xC8 2.--31. 0x4 " VECTOR50 ,AVIC Vector"
|
|
line.long 0xCC "VECTOR51,AVIC Vector Register 51"
|
|
hexmask.long 0xCC 2.--31. 0x4 " VECTOR51 ,AVIC Vector"
|
|
line.long 0xD0 "VECTOR52,AVIC Vector Register 52"
|
|
hexmask.long 0xD0 2.--31. 0x4 " VECTOR52 ,AVIC Vector"
|
|
line.long 0xD4 "VECTOR53,AVIC Vector Register 53"
|
|
hexmask.long 0xD4 2.--31. 0x4 " VECTOR53 ,AVIC Vector"
|
|
line.long 0xD8 "VECTOR54,AVIC Vector Register 54"
|
|
hexmask.long 0xD8 2.--31. 0x4 " VECTOR54 ,AVIC Vector"
|
|
line.long 0xDC "VECTOR55,AVIC Vector Register 55"
|
|
hexmask.long 0xDC 2.--31. 0x4 " VECTOR55 ,AVIC Vector"
|
|
line.long 0xE0 "VECTOR56,AVIC Vector Register 56"
|
|
hexmask.long 0xE0 2.--31. 0x4 " VECTOR56 ,AVIC Vector"
|
|
line.long 0xE4 "VECTOR57,AVIC Vector Register 57"
|
|
hexmask.long 0xE4 2.--31. 0x4 " VECTOR57 ,AVIC Vector"
|
|
line.long 0xE8 "VECTOR58,AVIC Vector Register 58"
|
|
hexmask.long 0xE8 2.--31. 0x4 " VECTOR58 ,AVIC Vector"
|
|
line.long 0xEC "VECTOR59,AVIC Vector Register 59"
|
|
hexmask.long 0xEC 2.--31. 0x4 " VECTOR59 ,AVIC Vector"
|
|
line.long 0xF0 "VECTOR60,AVIC Vector Register 60"
|
|
hexmask.long 0xF0 2.--31. 0x4 " VECTOR60 ,AVIC Vector"
|
|
line.long 0xF4 "VECTOR61,AVIC Vector Register 61"
|
|
hexmask.long 0xF4 2.--31. 0x4 " VECTOR61 ,AVIC Vector"
|
|
line.long 0xF8 "VECTOR62,AVIC Vector Register 62"
|
|
hexmask.long 0xF8 2.--31. 0x4 " VECTOR62 ,AVIC Vector"
|
|
line.long 0xFC "VECTOR63,AVIC Vector Register 63"
|
|
hexmask.long 0xFC 2.--31. 0x4 " VECTOR63 ,AVIC Vector"
|
|
width 0xb
|
|
tree.end
|
|
tree "CLKCTL (Clock Control Module)"
|
|
base ad:0x43f0c000
|
|
width 17.
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "GP_CTRL_SET/CLR,General Purpose Control Set/Clear Register"
|
|
setclrfld.long 0x00 12. 0x04 12. 0x08 12. " JSS_EN ,a11p_clk_off signal in the JSYNC enable" "Disabled,Enabled"
|
|
setclrfld.long 0x00 10. 0x04 10. 0x08 10. " AIPSB ,AIPS B's aips_byte_config[0] input" "Low,High"
|
|
textline " "
|
|
setclrfld.long 0x00 9. 0x04 9. 0x08 9. " AIPSA ,AIPS A's aips_byte_config[0] input" "Low,High"
|
|
setclrfld.long 0x00 8. 0x04 8. 0x08 8. " L2CC_EN ,Module level clock gating enable" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x04 7. 0x08 7. " DVFS_EN ,High speed DVFS enable" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x04 6. 0x08 6. " ETB_EN ,Clocks to ETB enable" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 5. 0x04 5. 0x08 5. " CTI_EN ,Clocks to CTI module enable" "Disabled,Enabled"
|
|
setclrfld.long 0x00 4. 0x04 4. 0x08 4. " TIM_EN ,Peripheral bus timeout monitors enable" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 3. 0x04 3. 0x08 3. " DOP[3] ,Driven Off-Platform" "Low,High"
|
|
setclrfld.long 0x00 2. 0x04 2. 0x08 2. " DOP[2] ,Driven Off-Platform" "Low,High"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x04 1. 0x08 1. " DOP[1] ,Driven Off-Platform" "Low,High"
|
|
setclrfld.long 0x00 0. 0x04 0. 0x08 0. " DOP[0] ,Driven Off-Platform" "Low,High"
|
|
rgroup.long 0x0c++0x3
|
|
line.long 0x00 "GP_STAT,General Purpose Status Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " GP_STAT ,Status"
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "L2_MEM_VAL,L2 Data Memory Val Register"
|
|
bitfld.long 0x00 12. " OFFSET ,VAL_OFFSET parameter in the level 2 cache RAM" "0,1"
|
|
bitfld.long 0x00 8.--11. " WVAL ,WVAL parameters in the level 2 cache RAM" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " RVAL2 ,RVAL2 parameters in the level 2 cache RAM" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 0.--3. " RVAL ,RVAL parameters in the level 2 cache RAM" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
group.long 0x14++0x3
|
|
line.long 0x00 "DBG_CTRL1,Debug Control Register 1"
|
|
bitfld.long 0x00 24. " EPS ,ETM11 ext_etm_extin3 Pulse Select" "Routed,Forced"
|
|
bitfld.long 0x00 19. " TIMS[7] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " TIMS[6] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " TIMS[5] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 16. " TIMS[4] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TIMS[1] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " TIMS[0] ,Controls trigger input multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
bitfld.long 0x00 11. " TOMS[7] ,Controls trigger output multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 10. " TOMS[6] ,Controls trigger output multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
bitfld.long 0x00 9. " TOMS[5] ,Controls trigger output multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " TOMS[4] ,Controls trigger output multiplexors in the ECTCTI wrapper" "Disabled,Enabled"
|
|
rgroup.long 0x20++0x03
|
|
line.long 0x00 "PLAT_ID,Platform ID Register"
|
|
hexmask.long.byte 0x00 28.--31. 1. " SPEC ,Describes the IP specification and defintion revision"
|
|
hexmask.long.byte 0x00 24.--27. 1. " IMPL ,Describes the IP implementation revision"
|
|
hexmask.long.byte 0x00 16.--23. 1. " MINOR ,Two-digit (BCD) field that describes the IP revision level"
|
|
hexmask.long.byte 0x00 8.--15. 1. " ECO ,Two-digit (BCD) field that describes changes to the implementation"
|
|
width 0xb
|
|
tree.end
|
|
tree "EVTMON (ARM11 Event Monitor)"
|
|
base ad:0x43f08000
|
|
width 7.
|
|
group.long 0x00++0x1f
|
|
line.long 0x00 "EMMC,Event Monitor Control Register"
|
|
bitfld.long 0x00 13. " EMC5_RST ,Counter Reset" "No reset,Reset"
|
|
bitfld.long 0x00 12. " EMC4_RST ,Counter Reset" "No reset,Reset"
|
|
bitfld.long 0x00 11. " EMC3_RST ,Counter Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 10. " EMC2_RST ,Counter Reset" "No reset,Reset"
|
|
bitfld.long 0x00 9. " EMC1_RST ,Counter Reset" "No reset,Reset"
|
|
bitfld.long 0x00 8. " EMC0_RST ,Counter Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 3.--5. " ESIPD ,Edge Sensitive Interrupt Pulse Duration" "1 cycle,2 cycles,4 cycles,8 cycles,16 cycles,32 cycles,64 cycles,128 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 2. " INT_POL ,Interrupt Polarity" "Active low,Active high"
|
|
bitfld.long 0x00 1. " INT_TYPE ,Interrupt Type" "Level,Edge"
|
|
bitfld.long 0x00 0. " ENABLE ,Event Monitor Enable" "Disabled,Enabled"
|
|
line.long 0x04 "EMCS,Counter Status Register"
|
|
eventfld.long 0x04 5. " EMC5_FLAG ,Event Counter 5 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x04 4. " EMC4_FLAG ,Event Counter 4 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x04 3. " EMC3_FLAG ,Event Counter 3 Flag" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x04 2. " EMC2_FLAG ,Event Counter 2 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x04 1. " EMC1_FLAG ,Event Counter 1 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x04 0. " EMC0_FLAG ,Event Counter 0 Flag" "Not occurred,Occurred"
|
|
line.long 0x8 "EMCC0,Counter Configuration Register 0"
|
|
bitfld.long 0x8 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0x8 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0x8 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
line.long 0xC "EMCC1,Counter Configuration Register 1"
|
|
bitfld.long 0xC 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0xC 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0xC 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
line.long 0x10 "EMCC2,Counter Configuration Register 2"
|
|
bitfld.long 0x10 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0x10 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0x10 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
line.long 0x14 "EMCC3,Counter Configuration Register 3"
|
|
bitfld.long 0x14 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0x14 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0x14 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
line.long 0x18 "EMCC4,Counter Configuration Register 4"
|
|
bitfld.long 0x18 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0x18 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0x18 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
line.long 0x1C "EMCC5,Counter Configuration Register 5"
|
|
bitfld.long 0x1C 2.--6. " CNT_EV_SRC ,Counter Event Source" "Disabled,Buffered write abort,L2 cache half-line eviction,Data read hit,Data read request,Data write hit,Data write request,Data write request (write through),Instruction read hit,Instruction read request,Write allocate,EMC5 overflow,EMC4 overflow,EMC3 overflow,EMC2 overflow,EMC1 overflow,EMC0 overflow,CLK cycle,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 1. " SET_COND ,Set Condition" "Overflow,Increment"
|
|
bitfld.long 0x1C 0. " INT_EN ,Interrupt Generation Enable" "Disabled,Enabled"
|
|
rgroup.long 0x20++0x17
|
|
line.long 0x00 "EMC0,Counter Register 0"
|
|
line.long 0x04 "EMC1,Counter Register 1"
|
|
line.long 0x08 "EMC2,Counter Register 2"
|
|
line.long 0x0c "EMC3,Counter Register 3"
|
|
line.long 0x10 "EMC4,Counter Register 4"
|
|
line.long 0x14 "EMC5,Counter Register 5"
|
|
width 0xb
|
|
tree.end
|
|
tree "MAX (Multi-Layer AHB Crossbar Switch)"
|
|
base ad:0x43F04000
|
|
width 8.
|
|
if (((data.long(asd:0x43F04000+0x10))&0x80000000)==0x00)
|
|
group.long 0x00++0x3 "Slave Port 0"
|
|
line.long 0x00 "MPR0,Master Priority Register 0"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "SGPCR0,General Purpose Control Register 0"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
else
|
|
rgroup.long 0x00++0x3 "Slave Port 0"
|
|
line.long 0x00 "MPR0,Master Priority Register 0"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "SGPCR0,General Purpose Control Register 0"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
endif
|
|
if (((data.long(asd:0x43F04000+0x110))&0x80000000)==0x00)
|
|
group.long 0x100++0x3 "Slave Port 1"
|
|
line.long 0x00 "MPR1,Master Priority Register 1"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
group.long 0x110++0x3
|
|
line.long 0x00 "SGPCR1,General Purpose Control Register 1"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
else
|
|
rgroup.long 0x100++0x3 "Slave Port 1"
|
|
line.long 0x00 "MPR1,Master Priority Register 1"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
rgroup.long 0x110++0x3
|
|
line.long 0x00 "SGPCR1,General Purpose Control Register 1"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
endif
|
|
if (((data.long(asd:0x43F04000+0x210))&0x80000000)==0x00)
|
|
group.long 0x200++0x3 "Slave Port 2"
|
|
line.long 0x00 "MPR2,Master Priority Register 2"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
group.long 0x210++0x3
|
|
line.long 0x00 "SGPCR2,General Purpose Control Register 2"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
else
|
|
rgroup.long 0x200++0x3 "Slave Port 2"
|
|
line.long 0x00 "MPR2,Master Priority Register 2"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
rgroup.long 0x210++0x3
|
|
line.long 0x00 "SGPCR2,General Purpose Control Register 2"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
endif
|
|
if (((data.long(asd:0x43F04000+0x310))&0x80000000)==0x00)
|
|
group.long 0x300++0x3 "Slave Port 3"
|
|
line.long 0x00 "MPR3,Master Priority Register 3"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
group.long 0x310++0x3
|
|
line.long 0x00 "SGPCR3,General Purpose Control Register 3"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
else
|
|
rgroup.long 0x300++0x3 "Slave Port 3"
|
|
line.long 0x00 "MPR3,Master Priority Register 3"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
rgroup.long 0x310++0x3
|
|
line.long 0x00 "SGPCR3,General Purpose Control Register 3"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
endif
|
|
if (((data.long(asd:0x43F04000+0x410))&0x80000000)==0x00)
|
|
group.long 0x400++0x3 "Slave Port 4"
|
|
line.long 0x00 "MPR4,Master Priority Register 4"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
group.long 0x410++0x3
|
|
line.long 0x00 "SGPCR4,General Purpose Control Register 4"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
else
|
|
rgroup.long 0x400++0x3 "Slave Port 4"
|
|
line.long 0x00 "MPR4,Master Priority Register 4"
|
|
bitfld.long 0x00 20.--22. " MSTR_5 ,Master 5 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 16.--18. " MSTR_4 ,Master 4 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 12.--14. " MSTR_3 ,Master 3 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MSTR_2 ,Master 2 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 4.--6. " MSTR_1 ,Master 1 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
bitfld.long 0x00 0.--2. " MSTR_0 ,Master 0 Priority" "Highest,1,2,3,4,5,6,Lowest"
|
|
rgroup.long 0x410++0x3
|
|
line.long 0x00 "SGPCR4,General Purpose Control Register 4"
|
|
bitfld.long 0x00 31. " RO ,Read Only" "Read/Write,Read only"
|
|
bitfld.long 0x00 30. " HLP ,Halt Low Priority" "Highest,Lowest"
|
|
bitfld.long 0x00 8.--9. " ARB ,Arbitration Mode" "Fixed,Round robin,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " PCTL ,Parking Control" "PARK,Last master,No master,?..."
|
|
bitfld.long 0x00 0.--2. " PARK ,Parking master" "Port 0,Port 1,Port 2,Port 3,Port 4,Port 5,?..."
|
|
endif
|
|
group.long 0x800++0x3 "Master Port 0"
|
|
line.long 0x00 "MGPCR0,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
group.long 0x900++0x3 "Master Port 1"
|
|
line.long 0x00 "MGPCR1,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
group.long 0xa00++0x3 "Master Port 2"
|
|
line.long 0x00 "MGPCR2,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
group.long 0xb00++0x3 "Master Port 3"
|
|
line.long 0x00 "MGPCR3,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
group.long 0xc00++0x3 "Master Port 4"
|
|
line.long 0x00 "MGPCR4,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
group.long 0xd00++0x3 "Master Port 5"
|
|
line.long 0x00 "MGPCR5,Master General Purpose Control Register"
|
|
bitfld.long 0x00 0.--2. " AULB ,Arbitrate on Undefined Length Bursts" "No arbitration,Any time,After 4 beats,After 8 beats,After 16 beats,?..."
|
|
width 0xb
|
|
tree.end
|
|
tree.open "IIM (IC Identification)"
|
|
base ad:0x53FF0000
|
|
width 7.
|
|
tree "Common Registers"
|
|
group.long 0x00++0x1b
|
|
line.byte 0x00 "STAT,Status Register"
|
|
bitfld.byte 0x00 7. " BUSY ,IIM busy" "Not busy,Busy"
|
|
eventfld.byte 0x00 1. " PRGD ,Program Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.byte 0x00 0. " SNSD ,Explicit Sense Cycle Done" "Not finished,Finished"
|
|
line.byte 0x04 "STATM,Status IRQ Mask Register"
|
|
bitfld.byte 0x04 1. " PRGD_M ,Program Done Mask" "Masked,Not masked"
|
|
bitfld.byte 0x04 0. " SNSD_M ,Explicit Sense Cycle Done Mask" "Masked,Not masked"
|
|
line.byte 0x08 "ERR,Module Errors Register"
|
|
eventfld.byte 0x08 7. " PRGE ,Program Error" "No error,Error"
|
|
eventfld.byte 0x08 6. " WPE ,Write Protect Error" "No error,Error"
|
|
textline " "
|
|
eventfld.byte 0x08 5. " OPE ,Override Protect Error" "No error,Error"
|
|
eventfld.byte 0x08 4. " RPE ,Read Protect Error" "No error,Error"
|
|
textline " "
|
|
eventfld.byte 0x08 3. " WLRE ,Write to Locked Register Error" "No error,Error"
|
|
eventfld.byte 0x08 2. " SNSE ,Explicit Sense Cycle Error" "No error,Error"
|
|
textline " "
|
|
eventfld.byte 0x08 1. " PARITYE ,Parity Error of cache" "No error,Error"
|
|
line.byte 0x0c "EMASK,Error IRQ Mask Register"
|
|
bitfld.byte 0x0c 7. " PRGE_M ,Program Error Mask" "Masked,Not masked"
|
|
bitfld.byte 0x0c 6. " WPE_M ,Write Protect Error Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.byte 0x0c 5. " OPE_M ,Override Protect Error Mask" "Masked,Not masked"
|
|
bitfld.byte 0x0c 4. " RPE_M ,Read Protect Error Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.byte 0x0c 3. " WLRE_M ,Write to Locked Register Error Mask" "Masked,Not masked"
|
|
bitfld.byte 0x0c 2. " SNSE_M ,Explicit Sense Cycle Error Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.byte 0x0c 1. " PARITYE_M ,Parity Error Mask" "Masked,Not masked"
|
|
line.byte 0x10 "FCTL,Fuse Control Register"
|
|
bitfld.byte 0x10 7. " DPC ,Delayed Program Cycle" "Not delayed,Delayed"
|
|
bitfld.byte 0x10 4.--6. " PRG_LENGTH ,Program Pulse Length" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.byte 0x10 3. " ESNS_N ,Explicit Sense Normal" "Normal,Initiated"
|
|
bitfld.byte 0x10 2. " ESNS_0 ,Explicit Sense 0-stressed" "Normal,Initiated"
|
|
textline " "
|
|
bitfld.byte 0x10 1. " ESNS_1 ,Explicit Sense 1-stressed" "Normal,Initiated"
|
|
bitfld.byte 0x10 0. " PRG ,Program" "Normal,Initiated"
|
|
line.byte 0x14 "UA,Upper Address"
|
|
hexmask.byte 0x14 0.--5. 1. " A[13:8] ,Top six bits of address"
|
|
line.byte 0x18 "LA,Lower Address"
|
|
hexmask.byte 0x18 0.--7. 1. " A[7:0] ,Bottom bits of address"
|
|
rgroup.long 0x1c++0xb
|
|
line.byte 0x00 "SDAT,Explicit Sense Data Register"
|
|
line.byte 0x04 "PREV,Product Revision Register"
|
|
hexmask.byte 0x04 3.--7. 1. " PROD_REV ,Product Revision"
|
|
hexmask.byte 0x04 0.--2. 1. " PROD_VT ,Product vendor or technology"
|
|
line.byte 0x08 "SREV,Silicon Revision Register"
|
|
hexmask.byte 0x08 0.--7. 1. " SILICON_REV ,Mask Set Revision"
|
|
group.long 0x28++0x13
|
|
line.byte 0x00 "PRG_P,Program Protection Register"
|
|
line.byte 0x04 "SCS0,Software-Controllable Signals Register 0"
|
|
bitfld.byte 0x04 7. " LOCK ,Register Lock" "Not locked,Locked"
|
|
bitfld.byte 0x04 6. " HAB_JDE ,HAB JTAG Debug Enable" "Disabled,Enabled"
|
|
textline " "
|
|
hexmask.byte 0x04 0.--5. 1. " SCS[26:21] ,These bits may be used in an implementation-defined way"
|
|
line.byte 0x08 "SCS1,Software-Controllable Signals Register 1"
|
|
bitfld.byte 0x08 7. " LOCK ,Register Lock" "Not locked,Locked"
|
|
hexmask.byte 0x08 0.--6. 1. " SCS[20:14] ,These bits may be used in an implementation-defined way"
|
|
line.byte 0x0c "SCS2,Software-Controllable Signals Register 2"
|
|
bitfld.byte 0x0c 7. " LOCK ,Register Lock" "Not locked,Locked"
|
|
hexmask.byte 0x0c 0.--6. 1. " SCS[13:7] ,These bits may be used in an implementation-defined way"
|
|
line.byte 0x10 "SCS3,Software-Controllable Signals Register 3"
|
|
bitfld.byte 0x10 7. " LOCK ,Register Lock" "Not locked,Locked"
|
|
hexmask.byte 0x10 0.--6. 1. " SCS[6:0] ,These bits may be used in an implementation-defined way"
|
|
tree.end
|
|
tree "Fuse Bank 0"
|
|
width 5.
|
|
group.long 0x800++0x7
|
|
line.byte 0x00 "FBAC0,Fuse Bank 0 Access Protection Register"
|
|
bitfld.byte 0x00 7. " FBWP ,Fuse Bank Write Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 6. " FBOP ,Fuse Bank Override Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FBRP ,Fuse Bank Read Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 4. " FBSP ,Fuse Bank Scan Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 3. " FBESP ,Fuse Banks Explicit Sense Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 2. " CRC_LOCK ,Rows 0018 and 0040 lock" "Low,High"
|
|
textline " "
|
|
bitfld.byte 0x00 1. " SIREV_LOCK ,SI_REV[7:0] field lock" "Unlocked,Locked"
|
|
line.byte 0x04 "JAC,JTAG Access Control Register"
|
|
bitfld.byte 0x04 7. " JTAG_LOCK ,Word Lock" "Unlocked,Locked"
|
|
bitfld.byte 0x04 5.--6. " JTAG_SMODE ,JTAG Security Mode" "JTAG enable,Secure JTAG,Reserved,No debug"
|
|
textline " "
|
|
bitfld.byte 0x04 3. " JTAG_HEO ,JTAG HAB Enable Override" "Disabled,Enabled"
|
|
bitfld.byte 0x04 2. " KTE ,Kill Trace Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x04 1. " SEC_JTAG_RE ,Secure JTAG Re-enable" "Not overridden,Overridden"
|
|
bitfld.byte 0x04 0. " JTAG_BP ,JTAG Debug Security Bypass" "Not activated,Activated"
|
|
if ((d.l(ad:0x53FF0000+0x814)&0x6)==0x0)
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 4. " BT_WEIM_MUXED ,WEIM muxed mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,Device select" "EEPROM,?..."
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "NOR,?..."
|
|
textline " "
|
|
bitfld.byte 0x08 4. " BT_EEPROM_CFG ,Use EEPROM DCD" "Used,Not used"
|
|
bitfld.byte 0x08 3. " BT_BUS_WIDTH ,WEIM NOR Bus Width" "16-bit,?..."
|
|
textline " "
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
elif ((d.l(ad:0x53FF0000+0x814)&0x6)==0x2)
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 5. " BT_ECC_SEL ,4/8-bit ECC" "4-bit,8-bit"
|
|
textline " "
|
|
bitfld.byte 0x00 2.--3. " BT_SPARE_SIZE ,Spare area size" "16-bytes,64-bytes,128-bytes,218-bytes"
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 5.--6. " BT_PAGE_SIZE ,NAND Flash Page Size" "512-bytes,2K-bytes,4K-bytes,?..."
|
|
textline " "
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,Device select" "EEPROM,?..."
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "3 addr. cycle,4 addr. cycle,5 addr. cycle,6 addr. cycle"
|
|
textline " "
|
|
bitfld.byte 0x08 3. " BT_BUS_WIDTH ,NAND Bus Width" "8-bit,16-bit"
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
textline " "
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
elif ((d.l(ad:0x53FF0000+0x814)&0x6)==0x4)
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
textline " "
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,Device select" "EEPROM,?..."
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "Reserved,P-ATA HDD,?..."
|
|
textline " "
|
|
bitfld.byte 0x08 4. " BT_EEPROM_CFG ,Use EEPROM DCD" "Used,Not used"
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
textline " "
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
elif ((d.l(ad:0x53FF0000+0x814)&0x66)==(0x26||0x46))
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
textline " "
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,Device select" "EEPROM,?..."
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "SD/MMC,Reserved,Serial ROM (I2C),Serial ROM (SPI)"
|
|
textline " "
|
|
bitfld.byte 0x08 4. " BT_EEPROM_CFG ,Use EEPROM DCD" "Used,Not used"
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
textline " "
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
elif ((d.l(ad:0x53FF0000+0x814)&0x66)==0x66)
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
textline " "
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,SPI type" "EEPROM,Serial Flash"
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "SD/MMC,Reserved,Serial ROM (I2C),Serial ROM (SPI)"
|
|
textline " "
|
|
bitfld.byte 0x08 4. " BT_EEPROM_CFG ,Use EEPROM DCD" "Used,Not used"
|
|
bitfld.byte 0x08 3. " BT_BUS_WIDTH ,SPI Bus Width" "16-bit,24-bit"
|
|
textline " "
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
elif ((d.l(ad:0x53FF0000+0x814)&0x66)==0x06)
|
|
group.long 0x80C++0xB
|
|
line.byte 0x00 "FC0,Fuse Control Register 0"
|
|
bitfld.byte 0x00 6.--7. " BT_SDMMC_SRC ,eSDHC controller for booting from" "eSDHC-1,eSDHC-2,eSDHC-3,?..."
|
|
bitfld.byte 0x00 5. " BT_ECC_SEL ,eMMC fast boot mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 2.--3. " BT_SPARE_SIZE ,SD fast boot mode" "Low,High,?..."
|
|
bitfld.byte 0x00 0.--1. " BT_USB_SRC ,USB PHY select" "UTMI PHY,ULPI PHY,ATLAS,PHILIPS 1301"
|
|
line.byte 0x04 "FC1,Fuse Control Register 1"
|
|
bitfld.byte 0x04 7. " BT_SPARE_FUSE ,Spare fuse" "Low,High"
|
|
bitfld.byte 0x04 3. " GPIO_BT_SEL ,GPIO Boot Select" "GPIO,Fuses"
|
|
textline " "
|
|
bitfld.byte 0x04 0.--2. " HAB_TYPE ,Security Type" "Enabled,Engineering,Enabled,Enabled,Disabled,Enabled,Enabled,Enabled"
|
|
line.byte 0x08 "FC2,Fuse Control Register 2"
|
|
bitfld.byte 0x08 7. " BT_SPI_TYPE ,SPI type" "EEPROM,Serial Flash"
|
|
bitfld.byte 0x08 5.--6. " BT_MEM_TYPE ,Boot Memory Type" "SD/MMC,Reserved,Serial ROM (I2C),Serial ROM (SPI)"
|
|
textline " "
|
|
bitfld.byte 0x08 4. " BT_EEPROM_CFG ,Use EEPROM DCD" "Used,Not used"
|
|
bitfld.byte 0x08 1.--2. " BT_MEM_CTL ,Boot Memory Control Type" "WEIM,NAND Flash,ATA HDD,Device"
|
|
textline " "
|
|
bitfld.byte 0x08 0. " DIR_BT_DIS ,Direct External Memory Boot Disable" "No,Yes"
|
|
endif
|
|
width 11.
|
|
group.long 0x81C++0x3
|
|
line.byte 0x00 "SREV_FUSE,Silicon Revision"
|
|
group.long 0x844++0x13
|
|
line.byte 0x00 "FUSE_LCK,Fuse Lock Register"
|
|
bitfld.byte 0x00 7. " RES0_LOCK ,Lock for rows 0048 -004C of fusebank 0" "Unlocked,Locked"
|
|
bitfld.byte 0x00 6. " TESTER_LOCK ,Lock for reserved fuses in rows 0058-007C of fusebank 0" "Unlocked,Locked"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " SRK0_LOCK ,Lock for SRK0_HASH[255:248] fuses in row 0050 of fusebank 0" "Unlocked,Locked"
|
|
bitfld.byte 0x00 4. " HAB_CUS_LOCK ,Lock for HAB_CUS[7:0] fuses in row 0054 of fusebank 0" "Unlocked,Locked"
|
|
textline " "
|
|
bitfld.byte 0x00 0. " BOOT_LOCK ,Lock for boot fuses in rows 000C-0018 of fusebank 0" "Unlocked,Locked"
|
|
line.byte 0x04 "BI_VER0, BI_VER[15:8] Value Register"
|
|
line.byte 0x08 "BI_VER1, BI_VER[7:0] Value Register"
|
|
line.byte 0x0C "HVR,SRK0_HASH[255:248] Value Register"
|
|
line.byte 0x10 "HAB_CC,HAB_CUS[7:0] Value Register"
|
|
tree.end
|
|
tree "Fuse Bank 1"
|
|
width 7.
|
|
group.long 0xC00++0x3
|
|
line.byte 0x00 "FBAC1,Fuse Bank Access Control 1"
|
|
bitfld.byte 0x00 7. " FBWP ,Fuse Bank Write Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 6. " FBOP ,Fuse Bank Override Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FBRP ,Fuse Bank Read Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 4. " FBSP ,Fuse Bank Scan Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 3. " FBESP ,Fuse Banks Explicit Sense Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 2. " L2VAL_LOCK ,Lock for rows 0078-007C of fusebank 1" "Unlocked,Locked"
|
|
textline " "
|
|
bitfld.byte 0x00 1. " SJC_RESP_LOCK ,SJC_RESP lock" "Unlocked,Locked"
|
|
bitfld.byte 0x00 0. " SCC_LOCK ,SCC_KEY lock" "Unlocked,Locked"
|
|
width 17.
|
|
wgroup.long 0xC04++0x53
|
|
line.byte 0x0 "KEY[167:160],SCC Key [167:160]"
|
|
line.byte 0x4 "KEY[159:152],SCC Key [159:152]"
|
|
line.byte 0x8 "KEY[151:144],SCC Key [151:144]"
|
|
line.byte 0xC "KEY[143:136],SCC Key [143:136]"
|
|
line.byte 0x10 "KEY[135:128],SCC Key [135:128]"
|
|
line.byte 0x14 "KEY[127:120],SCC Key [127:120]"
|
|
line.byte 0x18 "KEY[119:112],SCC Key [119:112]"
|
|
line.byte 0x1C "KEY[111:104],SCC Key [111:104]"
|
|
line.byte 0x20 "KEY[103:96],SCC Key [103:96]"
|
|
line.byte 0x24 "KEY[95:88],SCC Key [95:88]"
|
|
line.byte 0x28 "KEY[87:80],SCC Key [87:80]"
|
|
line.byte 0x2C "KEY[79:72],SCC Key [79:72]"
|
|
line.byte 0x30 "KEY[71:64],SCC Key [71:64]"
|
|
line.byte 0x34 "KEY[63:56],SCC Key [63:56]"
|
|
line.byte 0x38 "KEY[55:48],SCC Key [55:48]"
|
|
line.byte 0x3C "KEY[47:40],SCC Key [47:40]"
|
|
line.byte 0x40 "KEY[39:32],SCC Key [39:32]"
|
|
line.byte 0x44 "KEY[31:24],SCC Key [31:24]"
|
|
line.byte 0x48 "KEY[23:16],SCC Key [23:16]"
|
|
line.byte 0x4C "KEY[15:8],SCC Key [15:8]"
|
|
line.byte 0x50 "KEY[7:0],SCC Key [7:0]"
|
|
width 17.
|
|
group.long 0xC5C++0x1f
|
|
line.byte 0x0 "SJC_RESP[55:48],SJC_response[55:48] Register"
|
|
line.byte 0x4 "SJC_RESP[47:40],SJC_response[47:40] Register"
|
|
line.byte 0x8 "SJC_RESP[39:32],SJC_response[39:32] Register"
|
|
line.byte 0xC "SJC_RESP[31:24],SJC_response[31:24] Register"
|
|
line.byte 0x10 "SJC_RESP[23:16],SJC_response[23:16] Register"
|
|
line.byte 0x14 "SJC_RESP[15:8],SJC_response[15:8] Register"
|
|
line.byte 0x18 "SJC_RESP[7:0],SJC_response[7:0] Register"
|
|
tree.end
|
|
tree "Fuse Bank 2"
|
|
width 7.
|
|
group.long 0x1000++0x3
|
|
line.byte 0x00 "FBAC2,Fuse Bank 2 Access Protection Register"
|
|
bitfld.byte 0x00 7. " FBWP ,Fuse Bank Write Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 6. " FBOP ,Fuse Bank Override Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FBRP ,Fuse Bank Read Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 4. " FBSP ,Fuse Bank Scan Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 3. " FBESP ,Fuse Banks Explicit Sense Protect" "Not protected,Protected"
|
|
bitfld.byte 0x00 1. " SRK0_LOCK88 ,Fuse Banks Explicit Sense Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.byte 0x00 0. " SRK0_LOCK160 ,Fuse Banks Explicit Sense Protect" "Not protected,Protected"
|
|
width 19.
|
|
group.long 0x1004++0x7F
|
|
line.byte 0x0 "SRK0_HASH[247:240],SRK0_HASH[247:240]"
|
|
line.byte 0x4 "SRK0_HASH[239:232],SRK0_HASH[239:232]"
|
|
line.byte 0x8 "SRK0_HASH[231:224],SRK0_HASH[231:224]"
|
|
line.byte 0xC "SRK0_HASH[223:216],SRK0_HASH[223:216]"
|
|
line.byte 0x10 "SRK0_HASH[215:208],SRK0_HASH[215:208]"
|
|
line.byte 0x14 "SRK0_HASH[207:200],SRK0_HASH[207:200]"
|
|
line.byte 0x18 "SRK0_HASH[199:192],SRK0_HASH[199:192]"
|
|
line.byte 0x1C "SRK0_HASH[191:184],SRK0_HASH[191:184]"
|
|
line.byte 0x20 "SRK0_HASH[183:176],SRK0_HASH[183:176]"
|
|
line.byte 0x24 "SRK0_HASH[175:168],SRK0_HASH[175:168]"
|
|
line.byte 0x28 "SRK0_HASH[167:160],SRK0_HASH[167:160]"
|
|
line.byte 0x2C "SRK0_HASH[159:152],SRK0_HASH[159:152]"
|
|
line.byte 0x30 "SRK0_HASH[151:144],SRK0_HASH[151:144]"
|
|
line.byte 0x34 "SRK0_HASH[143:136],SRK0_HASH[143:136]"
|
|
line.byte 0x38 "SRK0_HASH[135:128],SRK0_HASH[135:128]"
|
|
line.byte 0x3C "SRK0_HASH[127:120],SRK0_HASH[127:120]"
|
|
line.byte 0x40 "SRK0_HASH[119:112],SRK0_HASH[119:112]"
|
|
line.byte 0x44 "SRK0_HASH[111:104],SRK0_HASH[111:104]"
|
|
line.byte 0x48 "SRK0_HASH[103:96],SRK0_HASH[103:96]"
|
|
line.byte 0x4C "SRK0_HASH[95:88],SRK0_HASH[95:88]"
|
|
line.byte 0x50 "SRK0_HASH[87:80],SRK0_HASH[87:80]"
|
|
line.byte 0x54 "SRK0_HASH[79:72],SRK0_HASH[79:72]"
|
|
line.byte 0x58 "SRK0_HASH[71:64],SRK0_HASH[71:64]"
|
|
line.byte 0x5C "SRK0_HASH[63:56],SRK0_HASH[63:56]"
|
|
line.byte 0x60 "SRK0_HASH[55:48],SRK0_HASH[55:48]"
|
|
line.byte 0x64 "SRK0_HASH[47:40],SRK0_HASH[47:40]"
|
|
line.byte 0x68 "SRK0_HASH[39:32],SRK0_HASH[39:32]"
|
|
line.byte 0x6C "SRK0_HASH[31:24],SRK0_HASH[31:24]"
|
|
line.byte 0x70 "SRK0_HASH[23:16],SRK0_HASH[23:16]"
|
|
line.byte 0x74 "SRK0_HASH[15:8],SRK0_HASH[15:8]"
|
|
line.byte 0x78 "SRK0_HASH[7:0],SRK0_HASH[7:0]"
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree.open "EMI (External Memory Interface)"
|
|
tree "ESDCTL (Enhanced SDRAM Controller)"
|
|
base ad:0xb8001000
|
|
width 0xB
|
|
if ((data.long(asd:0xb8001000+0x00)&0xc00)==(0x000||0x400))
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "ESDCTL0,Enhanced SDRAM Control Register 0"
|
|
bitfld.long 0x00 31. " SDE ,Enhanced SDRAM Controller Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28.--30. " SMODE ,SDRAM Controller Operating Mode" "Normal R/W,Precharge Command,Auto-Refresh Command,Load Mode Register Command,Manual Self Refresh,?..."
|
|
textline " "
|
|
bitfld.long 0x00 27. " SP ,Supervisor Protect" "Allowed,Prohibited"
|
|
bitfld.long 0x00 24.--26. " ROW ,Row Address Width" "11,12,13,14,?..."
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " COL ,Column Address Width" "8,9,10,?..."
|
|
bitfld.long 0x00 16.--17. " DSIZ ,SDRAM Memory Data Width" "16-bit D[31:16],16-bit D[15:0],32-bit,?..."
|
|
textline " "
|
|
bitfld.long 0x00 13.--15. " SREFR ,SDRAM Refresh Rate" "Disabled,1,2,4,8,16,?..."
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " PWDT ,Power Down Timer" "Disabled/Run Mode,No banks active/Precharge power down,64 clocks/Active power down,128 clocks/Active power down"
|
|
textline " "
|
|
bitfld.long 0x00 8. " FP ,Full Page" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BL ,Burst Length" "4,8"
|
|
bitfld.long 0x00 0.--5. " PRCT ,Precharge Timer" "Disabled,2 clocks,4 clocks,6 clocks,8 clocks,10 clocks,12 clocks,14 clocks,16 clocks,18 clocks,20 clocks,22 clocks,24 clocks,26 clocks,28 clocks,30 clocks,32 clocks,34 clocks,36 clocks,38 clocks,40 clocks,42 clocks,44 clocks,46 clocks,48 clocks,50 clocks,52 clocks,54 clocks,56 clocks,58 clocks,60 clocks,62 clocks,64 clocks,66 clocks,68 clocks,70 clocks,72 clocks,74 clocks,76 clocks,78 clocks,80 clocks,82 clocks,84 clocks,86 clocks,88 clocks,90 clocks,92 clocks,94 clocks,96 clocks,98 clocks,100 clocks,102 clocks,104 clocks,106 clocks,108 clocks,110 clocks,112 clocks,114 clocks,116 clocks,118 clocks,120 clocks,122 clocks,124 clocks,126 clocks"
|
|
else
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "ESDCTL0,Enhanced SDRAM Control Register 0"
|
|
bitfld.long 0x00 31. " SDE ,Enhanced SDRAM Controller Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28.--30. " SMODE ,SDRAM Controller Operating Mode" "Normal R/W,Precharge Command,Auto-Refresh Command,Load Mode Register Command,Manual Self Refresh,?..."
|
|
textline " "
|
|
bitfld.long 0x00 27. " SP ,Supervisor Protect" "Allowed,Prohibited"
|
|
bitfld.long 0x00 24.--26. " ROW ,Row Address Width" "11,12,13,14,?..."
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " COL ,Column Address Width" "8,9,10,?..."
|
|
bitfld.long 0x00 16.--17. " DSIZ ,SDRAM Memory Data Width" "16-bit D[31:16],16-bit D[15:0],32-bit,?..."
|
|
textline " "
|
|
bitfld.long 0x00 13.--15. " SREFR ,SDRAM Refresh Rate" "Disabled,1,2,4,8,16,?..."
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " PWDT ,Power Down Timer" "Disabled/Run Mode,No banks active/Precharge power down,64 clocks/Active power down,128 clocks/Active power down"
|
|
textline " "
|
|
bitfld.long 0x00 8. " FP ,Full Page" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BL ,Burst Length" "4,8"
|
|
endif
|
|
group.long 0x04++0x3
|
|
line.long 0x00 "ESDCFG0,Enhanced SDRAM Configuration Register 0"
|
|
bitfld.long 0x00 21.--22. " TXP_0 ,LPDDR exit power down to next valid command delay" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
bitfld.long 0x00 20. " TWTR_0 ,tLPDDR WRITE to READ Command Delay" "1 clock,2 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " TRP_0 ,SDRAM Row Precharge Delay" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
bitfld.long 0x00 16.--17. " TMRD_0 ,tMRD - SDRAM Load Mode Register to ACTIVE Command" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 15. " TWR_0 ,SDRAM WRITE to PRECHARGE Command" "2 clocks,3 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 12.--14. " TRAS_0 ,SDRAM ACTIVE to PRECHARGE Command" "1 clock,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks"
|
|
bitfld.long 0x00 10.--11. " TRRD_0 ,ACTIVE Bank A to ACTIVE Bank B Command" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " TCAS_0 ,SDRAM CAS Latency" "3 clocks only for LPDDR SDRAM,Reserved,2 clocks SDR and LPDDR SDRAM,3 clocks SDR and LPDDR SDRAM"
|
|
textline " "
|
|
bitfld.long 0x00 4.--6. " TRCD_0 ,SDRAM Row to Column Delay" "1 clock,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks"
|
|
bitfld.long 0x00 0.--3. " TRC_0 ,SDRAM Row Cycle Delay" "20 clocks,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks,9 clocks,10 clocks,11 clocks,12 clocks,13 clocks,14 clocks,15 clocks,16 clocks"
|
|
if ((data.long(asd:0xb8001000+0x08)&0xc00)==(0x000||0x400))
|
|
group.long 0x08++0x3
|
|
line.long 0x00 "ESDCTL1,Enhanced SDRAM Control Register 1"
|
|
bitfld.long 0x00 31. " SDE ,Enhanced SDRAM Controller Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28.--30. " SMODE ,SDRAM Controller Operating Mode" "Normal R/W,Precharge Command,Auto-Refresh Command,Load Mode Register Command,Manual Self Refresh,?..."
|
|
textline " "
|
|
bitfld.long 0x00 27. " SP ,Supervisor Protect" "Allowed,Prohibited"
|
|
bitfld.long 0x00 24.--26. " ROW ,Row Address Width" "11,12,13,14,?..."
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " COL ,Column Address Width" "8,9,10,?..."
|
|
bitfld.long 0x00 16.--17. " DSIZ ,SDRAM Memory Data Width" "16-bit D[31:16],16-bit D[15:0],32-bit,?..."
|
|
textline " "
|
|
bitfld.long 0x00 13.--15. " SREFR ,SDRAM Refresh Rate" "Disabled,1,2,4,8,16,?..."
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " PWDT ,Power Down Timer" "Disabled/Run Mode,No banks active/Precharge power down,64 clocks/Active power down,128 clocks/Active power down"
|
|
textline " "
|
|
bitfld.long 0x00 8. " FP ,Full Page" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BL ,Burst Length" "4,8"
|
|
bitfld.long 0x00 0.--5. " PRCT ,Precharge Timer" "Disabled,2 clocks,4 clocks,6 clocks,8 clocks,10 clocks,12 clocks,14 clocks,16 clocks,18 clocks,20 clocks,22 clocks,24 clocks,26 clocks,28 clocks,30 clocks,32 clocks,34 clocks,36 clocks,38 clocks,40 clocks,42 clocks,44 clocks,46 clocks,48 clocks,50 clocks,52 clocks,54 clocks,56 clocks,58 clocks,60 clocks,62 clocks,64 clocks,66 clocks,68 clocks,70 clocks,72 clocks,74 clocks,76 clocks,78 clocks,80 clocks,82 clocks,84 clocks,86 clocks,88 clocks,90 clocks,92 clocks,94 clocks,96 clocks,98 clocks,100 clocks,102 clocks,104 clocks,106 clocks,108 clocks,110 clocks,112 clocks,114 clocks,116 clocks,118 clocks,120 clocks,122 clocks,124 clocks,126 clocks"
|
|
else
|
|
group.long 0x08++0x3
|
|
line.long 0x00 "ESDCTL1,Enhanced SDRAM Control Register 1"
|
|
bitfld.long 0x00 31. " SDE ,Enhanced SDRAM Controller Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28.--30. " SMODE ,SDRAM Controller Operating Mode" "Normal R/W,Precharge Command,Auto-Refresh Command,Load Mode Register Command,Manual Self Refresh,?..."
|
|
textline " "
|
|
bitfld.long 0x00 27. " SP ,Supervisor Protect" "Allowed,Prohibited"
|
|
bitfld.long 0x00 24.--26. " ROW ,Row Address Width" "11,12,13,14,?..."
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " COL ,Column Address Width" "8,9,10,?..."
|
|
bitfld.long 0x00 16.--17. " DSIZ ,SDRAM Memory Data Width" "16-bit D[31:16],16-bit D[15:0],32-bit,?..."
|
|
textline " "
|
|
bitfld.long 0x00 13.--15. " SREFR ,SDRAM Refresh Rate" "Disabled,1,2,4,8,16,?..."
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " PWDT ,Power Down Timer" "Disabled/Run Mode,No banks active/Precharge power down,64 clocks/Active power down,128 clocks/Active power down"
|
|
textline " "
|
|
bitfld.long 0x00 8. " FP ,Full Page" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BL ,Burst Length" "4,8"
|
|
endif
|
|
group.long 0x0c++0x3
|
|
line.long 0x00 "ESDCFG1,Enhanced SDRAM Configuration Register 1"
|
|
bitfld.long 0x00 21.--22. " TXP_1 ,LPDDR exit power down to next valid command delay" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
bitfld.long 0x00 20. " TWTR_1 ,tLPDDR WRITE to READ Command Delay" "1 clock,2 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " TRP_1 ,SDRAM Row Precharge Delay" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
bitfld.long 0x00 16.--17. " TMRD_1 ,tMRD - SDRAM Load Mode Register to ACTIVE Command" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 15. " TWR_1 ,SDRAM WRITE to PRECHARGE Command" "2 clocks,3 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 12.--14. " TRAS_1 ,SDRAM ACTIVE to PRECHARGE Command" "1 clock,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks"
|
|
bitfld.long 0x00 10.--11. " TRRD_1 ,ACTIVE Bank A to ACTIVE Bank B Command" "1 clock,2 clocks,3 clocks,4 clocks"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " TCAS_1 ,SDRAM CAS Latency" "3 clocks only for LPDDR SDRAM,Reserved,2 clocks SDR and LPDDR SDRAM,3 clocks SDR and LPDDR SDRAM"
|
|
textline " "
|
|
bitfld.long 0x00 4.--6. " TRCD_1 ,SDRAM Row to Column Delay" "1 clock,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks"
|
|
bitfld.long 0x00 0.--3. " TRC_1 ,SDRAM Row Cycle Delay" "20 clocks,2 clocks,3 clocks,4 clocks,5 clocks,6 clocks,7 clocks,8 clocks,9 clocks,10 clocks,11 clocks,12 clocks,13 clocks,14 clocks,15 clocks,16 clocks"
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "ESDMISC,ESDMISC Miscellaneous Register"
|
|
bitfld.long 0x00 31. " SDRAMRDY ,External SDRAM/LPDDR Device Status" "Not ready,Ready"
|
|
bitfld.long 0x00 9. " DDR2_EN ,Regular (non-mobile) DDR2 device is connected" "Not used,Used"
|
|
textline " "
|
|
bitfld.long 0x00 8. " DDR_EN ,Regular (non mobile) DDR1 device is connected" "Not used,Used"
|
|
bitfld.long 0x00 7. " FRC_MSR ,Force measurement" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x00 6. " MA10_SHARE ,MA10 share" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " LHD ,Latency Hiding Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 4. " MDDR_MDIS ,LPDDR Delay Line Measure Disable" "No,Yes"
|
|
bitfld.long 0x00 3. " MDDR_DL_RST ,LPDDR Delay Line Soft Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 2. " MDDREN ,Enable DDR SDRAM device" "SDR,DDR"
|
|
bitfld.long 0x00 1. " RST ,Software Initiated Local Module Reset" "Disabled,Initiated"
|
|
group.long 0x20++0x13
|
|
line.long 0x00 "ESDCDLY1,MDDR Delay Line 1 Configuration Debug Register"
|
|
bitfld.long 0x00 31. " SEL_DLY_REG_1 ,Line 1 Delay" "1/4 cycle,DLY_REG_1"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DLY_OFFSET_1 ,Delay Line 1 offset value"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " DLY_ABS_OFFSET_1 ,Absolute delay offset"
|
|
hexmask.long.byte 0x00 0.--7. 1. " DLY_REG_1 ,Line 1 Delay"
|
|
line.long 0x04 "ESDCDLY2,MDDR Delay Line 2 Configuration Debug Register"
|
|
bitfld.long 0x04 31. " SEL_DLY_REG_2 ,Line 2 Delay" "1/4 cycle,DLY_REG_2"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DLY_OFFSET_2 ,Delay Line 2 offset value"
|
|
textline " "
|
|
hexmask.long.byte 0x04 8.--15. 1. " DLY_ABS_OFFSET_2 ,Absolute delay offset"
|
|
hexmask.long.byte 0x04 0.--7. 1. " DLY_REG_2 ,Line 2 Delay"
|
|
line.long 0x08 "ESDCDLY3,MDDR Delay Line 3 Configuration Debug Register"
|
|
bitfld.long 0x08 31. " SEL_DLY_REG_3 ,Line 3 Delay" "1/4 cycle,DLY_REG_3"
|
|
hexmask.long.byte 0x08 16.--23. 1. " DLY_OFFSET_3 ,Delay Line 3 offset value"
|
|
textline " "
|
|
hexmask.long.byte 0x08 8.--15. 1. " DLY_ABS_OFFSET_3 ,Absolute delay offset"
|
|
hexmask.long.byte 0x08 0.--7. 1. " DLY_REG_3 ,Line 3 Delay"
|
|
line.long 0x0c "ESDCDLY4,MDDR Delay Line 4 Configuration Debug Register"
|
|
bitfld.long 0x0c 31. " SEL_DLY_REG_4 ,Line 4 Delay" "1/4 cycle,DLY_REG_4"
|
|
hexmask.long.byte 0x0c 16.--23. 1. " DLY_OFFSET_4 ,Delay Line 4 offset value"
|
|
textline " "
|
|
hexmask.long.byte 0x0c 8.--15. 1. " DLY_ABS_OFFSET_4 ,Absolute delay offset"
|
|
hexmask.long.byte 0x0c 0.--7. 1. " DLY_REG_4 ,Line 4 Delay"
|
|
line.long 0x10 "ESDCDLY5,MDDR Delay Line 5 Configuration Debug Register"
|
|
bitfld.long 0x10 31. " SEL_DLY_REG_5 ,Line 5 Delay" "1/4 cycle,DLY_REG_5"
|
|
hexmask.long.byte 0x10 16.--23. 1. " DLY_OFFSET_5 ,Delay Line 5 offset value"
|
|
textline " "
|
|
hexmask.long.byte 0x10 8.--15. 1. " DLY_ABS_OFFSET_5 ,Absolute delay offset"
|
|
hexmask.long.byte 0x10 0.--7. 1. " DLY_REG_5 ,Line 5 Delay"
|
|
rgroup.long 0x34++0x3
|
|
line.long 0x00 "ESDCDLYL,MDDR Delay Line Cycle Debug Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " QTR_CYCLE_LENGTH ,Small Delay Number"
|
|
width 6.
|
|
base asd:0x80000000
|
|
group.long 0x00++0x3 "Memory"
|
|
line.long 0x00 "CSD0,CSD0 SDRAM/MDDR Memory Region"
|
|
button "CSD0" "d asd:0x80000000--asd:0x8fffffff /long"
|
|
base asd:0x90000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CSD1,CSD1 SDRAM/MDDR Memory Region"
|
|
button "CSD1" "d asd:0x90000000--asd:0x9fffffff /long"
|
|
;
|
|
;base ad:0xa0000000
|
|
;group.long 0x00++0x3 "Memory"
|
|
; line.long 0x00 "CSD0,CSD0 SDRAM/MDDR Memory Region"
|
|
; button "CSD0" "d ad:0xa0000000--ad:0xafffffff /long"
|
|
;base ad:0xb0000000
|
|
;group.long 0x00++0x3
|
|
; line.long 0x00 "CSD1,CSD1 SDRAM/MDDR Memory Region"
|
|
; button "CSD1" "d ad:0xb0000000--ad:0xbfffffff /long"
|
|
width 0xb
|
|
tree.end
|
|
tree "M3IF (Multi-Master Memory Interface)"
|
|
base ad:0xb8003000
|
|
width 11.
|
|
group.long 0x00++0x3 "Registers Space"
|
|
line.long 0x00 "M3IFCTL,M3IF Control Register"
|
|
bitfld.long 0x00 31. " SDA ,SDRAM/LPDDR/DDR2 Memory Active" "Not active,Active"
|
|
bitfld.long 0x00 11. " MLSD_EN ,Master Lock SDRAM/LPDDR/DDR2 Access" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " MLSD ,Master Lock SDRAM/LPDDR/DDR2 Access" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x00 7. " MRRP[7] ,Master 7 Round Robin Priority" "Not added,Added"
|
|
textline " "
|
|
bitfld.long 0x00 6. " MRRP[6] ,Master 6 Round Robin Priority" "Not added,Added"
|
|
bitfld.long 0x00 5. " MRRP[5] ,Master 5 Round Robin Priority" "Not added,Added"
|
|
textline " "
|
|
bitfld.long 0x00 4. " MRRP[4] ,Master 4 Round Robin Priority" "Not added,Added"
|
|
bitfld.long 0x00 3. " MRRP[3] ,Master 3 Round Robin Priority" "Not added,Added"
|
|
textline " "
|
|
bitfld.long 0x00 2. " MRRP[2] ,Master 2 Round Robin Priority" "Not added,Added"
|
|
bitfld.long 0x00 1. " MRRP[1] ,Master 1 Round Robin Priority" "Not added,Added"
|
|
textline " "
|
|
bitfld.long 0x00 0. " MRRP[0] ,Master 0 Round Robin Priority" "Not added,Added"
|
|
group.long 0x04++0x1f
|
|
line.long 0x0 "M3IFWCFG0,M3IF WaterMark Configuration Register 0"
|
|
hexmask.long 0x0 10.--31. 0x400 " WBA0 ,WaterMark Memory Region 0 Base Address"
|
|
line.long 0x4 "M3IFWCFG1,M3IF WaterMark Configuration Register 1"
|
|
hexmask.long 0x4 10.--31. 0x400 " WBA1 ,WaterMark Memory Region 1 Base Address"
|
|
line.long 0x8 "M3IFWCFG2,M3IF WaterMark Configuration Register 2"
|
|
hexmask.long 0x8 10.--31. 0x400 " WBA2 ,WaterMark Memory Region 2 Base Address"
|
|
line.long 0xC "M3IFWCFG3,M3IF WaterMark Configuration Register 3"
|
|
hexmask.long 0xC 10.--31. 0x400 " WBA3 ,WaterMark Memory Region 3 Base Address"
|
|
line.long 0x10 "M3IFWCFG4,M3IF WaterMark Configuration Register 4"
|
|
hexmask.long 0x10 10.--31. 0x400 " WBA4 ,WaterMark Memory Region 4 Base Address"
|
|
line.long 0x14 "M3IFWCFG5,M3IF WaterMark Configuration Register 5"
|
|
hexmask.long 0x14 10.--31. 0x400 " WBA5 ,WaterMark Memory Region 5 Base Address"
|
|
line.long 0x18 "M3IFWCFG6,M3IF WaterMark Configuration Register 6"
|
|
hexmask.long 0x18 10.--31. 0x400 " WBA6 ,WaterMark Memory Region 6 Base Address"
|
|
line.long 0x1C "M3IFWCFG7,M3IF WaterMark Configuration Register 7"
|
|
hexmask.long 0x1C 10.--31. 0x400 " WBA7 ,WaterMark Memory Region 7 Base Address"
|
|
group.long 0x24++0x17
|
|
line.long 0x00 "M3IFWCSR,M3IF WaterMark Control and Status Register"
|
|
bitfld.long 0x00 31. " WIE ,WaterMark Interrupt Enable" "Disabled,Enabled"
|
|
eventfld.long 0x00 7. " WS7 ,WaterMark Status 7" "Not occurred,Occurred"
|
|
eventfld.long 0x00 6. " WS6 ,WaterMark Status 6" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 5. " WS5 ,WaterMark Status 5" "Not occurred,Occurred"
|
|
eventfld.long 0x00 4. " WS4 ,WaterMark Status 4" "Not occurred,Occurred"
|
|
eventfld.long 0x00 3. " WS3 ,WaterMark Status 3" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 2. " WS2 ,WaterMark Status 2" "Not occurred,Occurred"
|
|
eventfld.long 0x00 1. " WS1 ,WaterMark Status 1" "Not occurred,Occurred"
|
|
eventfld.long 0x00 0. " WS0 ,WaterMark Status 0" "Not occurred,Occurred"
|
|
line.long 0x04 "M3IFSCFG0,M3IF Snooping Configuration Register 0"
|
|
hexmask.long 0x04 11.--31. 0x800 " SWBA ,Snooping Window Base Address"
|
|
bitfld.long 0x04 1.--4. " SWSZ ,Snooping Window Size" "2 KB,4 KB,8 KB,16 KB,32 KB,64 KB,128 KB,256 KB,512 KB,1 MB,2 MB,4 MB,8 MB,16 MB,?..."
|
|
bitfld.long 0x04 0. " SE ,Snooping Enable" "Disabled,Enabled"
|
|
line.long 0x08 "M3IFSCFG1,M3IF Snooping Configuration Register 1"
|
|
bitfld.long 0x08 31. " SSE0[31] ,Snooping Segment 31 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 30. " SSE0[30] ,Snooping Segment 30 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 29. " SSE0[29] ,Snooping Segment 29 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 28. " SSE0[28] ,Snooping Segment 28 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 27. " SSE0[27] ,Snooping Segment 27 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 26. " SSE0[26] ,Snooping Segment 26 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 25. " SSE0[25] ,Snooping Segment 25 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " SSE0[24] ,Snooping Segment 24 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 23. " SSE0[23] ,Snooping Segment 23 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 22. " SSE0[22] ,Snooping Segment 22 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 21. " SSE0[21] ,Snooping Segment 21 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 20. " SSE0[20] ,Snooping Segment 20 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 19. " SSE0[19] ,Snooping Segment 19 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 18. " SSE0[18] ,Snooping Segment 18 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 17. " SSE0[17] ,Snooping Segment 17 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 16. " SSE0[16] ,Snooping Segment 16 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 15. " SSE0[15] ,Snooping Segment 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 14. " SSE0[14] ,Snooping Segment 14 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 13. " SSE0[13] ,Snooping Segment 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 12. " SSE0[12] ,Snooping Segment 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 11. " SSE0[11] ,Snooping Segment 11 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 10. " SSE0[10] ,Snooping Segment 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 9. " SSE0[9] ,Snooping Segment 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " SSE0[8] ,Snooping Segment 8 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " SSE0[7] ,Snooping Segment 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " SSE0[6] ,Snooping Segment 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 5. " SSE0[5] ,Snooping Segment 5 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 4. " SSE0[4] ,Snooping Segment 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 3. " SSE0[3] ,Snooping Segment 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " SSE0[2] ,Snooping Segment 2 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " SSE0[1] ,Snooping Segment 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " SSE0[0] ,Snooping Segment 0 Enable" "Disabled,Enabled"
|
|
line.long 0x0c "M3IFSCFG2,M3IF Snooping Configuration Register 2"
|
|
bitfld.long 0x0c 31. " SSE1[63] ,Snooping Segment 63 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 30. " SSE1[62] ,Snooping Segment 62 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 29. " SSE1[61] ,Snooping Segment 61 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 28. " SSE1[60] ,Snooping Segment 60 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 27. " SSE1[59] ,Snooping Segment 59 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 26. " SSE1[58] ,Snooping Segment 58 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 25. " SSE1[57] ,Snooping Segment 57 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 24. " SSE1[56] ,Snooping Segment 56 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 23. " SSE1[55] ,Snooping Segment 55 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 22. " SSE1[54] ,Snooping Segment 54 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 21. " SSE1[53] ,Snooping Segment 53 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 20. " SSE1[52] ,Snooping Segment 52 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 19. " SSE1[51] ,Snooping Segment 51 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 18. " SSE1[50] ,Snooping Segment 50 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 17. " SSE1[49] ,Snooping Segment 49 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 16. " SSE1[48] ,Snooping Segment 48 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 15. " SSE1[47] ,Snooping Segment 47 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 14. " SSE1[46] ,Snooping Segment 46 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 13. " SSE1[45] ,Snooping Segment 45 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 12. " SSE1[44] ,Snooping Segment 44 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 11. " SSE1[43] ,Snooping Segment 43 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 10. " SSE1[42] ,Snooping Segment 42 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 9. " SSE1[41] ,Snooping Segment 41 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 8. " SSE1[40] ,Snooping Segment 40 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " SSE1[39] ,Snooping Segment 39 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 6. " SSE1[38] ,Snooping Segment 38 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 5. " SSE1[37] ,Snooping Segment 37 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 4. " SSE1[36] ,Snooping Segment 36 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 3. " SSE1[35] ,Snooping Segment 35 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 2. " SSE1[34] ,Snooping Segment 34 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " SSE1[33] ,Snooping Segment 33 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 0. " SSE1[32] ,Snooping Segment 32 Enable" "Disabled,Enabled"
|
|
line.long 0x10 "M3IFSSR0,M3IF Snooping Status Register 0"
|
|
bitfld.long 0x10 31. " SSS0[31] ,Snooping Segment 31 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 30. " SSS0[30] ,Snooping Segment 30 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 29. " SSS0[29] ,Snooping Segment 29 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 28. " SSS0[28] ,Snooping Segment 28 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 27. " SSS0[27] ,Snooping Segment 27 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 26. " SSS0[26] ,Snooping Segment 26 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 25. " SSS0[25] ,Snooping Segment 25 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 24. " SSS0[24] ,Snooping Segment 24 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 23. " SSS0[23] ,Snooping Segment 23 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 22. " SSS0[22] ,Snooping Segment 22 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 21. " SSS0[21] ,Snooping Segment 21 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 20. " SSS0[20] ,Snooping Segment 20 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 19. " SSS0[19] ,Snooping Segment 19 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 18. " SSS0[18] ,Snooping Segment 18 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 17. " SSS0[17] ,Snooping Segment 17 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 16. " SSS0[16] ,Snooping Segment 16 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 15. " SSS0[15] ,Snooping Segment 15 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 14. " SSS0[14] ,Snooping Segment 14 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 13. " SSS0[13] ,Snooping Segment 13 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 12. " SSS0[12] ,Snooping Segment 12 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 11. " SSS0[11] ,Snooping Segment 11 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 10. " SSS0[10] ,Snooping Segment 10 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 9. " SSS0[9] ,Snooping Segment 9 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 8. " SSS0[8] ,Snooping Segment 8 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 7. " SSS0[7] ,Snooping Segment 7 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 6. " SSS0[6] ,Snooping Segment 6 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 5. " SSS0[5] ,Snooping Segment 5 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 4. " SSS0[4] ,Snooping Segment 4 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 3. " SSS0[3] ,Snooping Segment 3 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 2. " SSS0[2] ,Snooping Segment 2 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x10 1. " SSS0[1] ,Snooping Segment 1 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x10 0. " SSS0[0] ,Snooping Segment 0 Status" "Not occurred,Occurred"
|
|
line.long 0x14 "M3IFSSR1,M3IF Snooping Status Register 1"
|
|
bitfld.long 0x14 31. " SSS1[63] ,Snooping Segment 63 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 30. " SSS1[62] ,Snooping Segment 62 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 29. " SSS1[61] ,Snooping Segment 61 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 28. " SSS1[60] ,Snooping Segment 60 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 27. " SSS1[59] ,Snooping Segment 59 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 26. " SSS1[58] ,Snooping Segment 58 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 25. " SSS1[57] ,Snooping Segment 57 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 24. " SSS1[56] ,Snooping Segment 56 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 23. " SSS1[55] ,Snooping Segment 55 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 22. " SSS1[54] ,Snooping Segment 54 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 21. " SSS1[53] ,Snooping Segment 53 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 20. " SSS1[52] ,Snooping Segment 52 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 19. " SSS1[51] ,Snooping Segment 51 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 18. " SSS1[50] ,Snooping Segment 50 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 17. " SSS1[49] ,Snooping Segment 49 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 16. " SSS1[48] ,Snooping Segment 48 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 15. " SSS1[47] ,Snooping Segment 47 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 14. " SSS1[46] ,Snooping Segment 46 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 13. " SSS1[45] ,Snooping Segment 45 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 12. " SSS1[44] ,Snooping Segment 44 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 11. " SSS1[43] ,Snooping Segment 43 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 10. " SSS1[42] ,Snooping Segment 42 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 9. " SSS1[41] ,Snooping Segment 41 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 8. " SSS1[40] ,Snooping Segment 40 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 7. " SSS1[39] ,Snooping Segment 39 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 6. " SSS1[38] ,Snooping Segment 38 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 5. " SSS1[37] ,Snooping Segment 37 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 4. " SSS1[36] ,Snooping Segment 36 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 3. " SSS1[35] ,Snooping Segment 35 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 2. " SSS1[34] ,Snooping Segment 34 Status" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 1. " SSS1[33] ,Snooping Segment 33 Status" "Not occurred,Occurred"
|
|
bitfld.long 0x14 0. " SSS1[32] ,Snooping Segment 32 Status" "Not occurred,Occurred"
|
|
group.long 0x40++0x17
|
|
line.long 0x0 "M3IFMLWE0,M3IF Master Lock WEIM CS0 Register"
|
|
bitfld.long 0x0 31. " WEMA0 ,WEIM CS0 Memory Active" "Not active,Active"
|
|
bitfld.long 0x0 3. " MLWE0_EN ,Master Lock WEIM CS0 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 0.--2. " MLWE0 ,Master Lock WEIM CS0 Access" "0,1,2,3,4,5,6,7"
|
|
line.long 0x4 "M3IFMLWE1,M3IF Master Lock WEIM CS1 Register"
|
|
bitfld.long 0x4 31. " WEMA1 ,WEIM CS1 Memory Active" "Not active,Active"
|
|
bitfld.long 0x4 3. " MLWE1_EN ,Master Lock WEIM CS1 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 0.--2. " MLWE1 ,Master Lock WEIM CS1 Access" "0,1,2,3,4,5,6,7"
|
|
line.long 0x8 "M3IFMLWE2,M3IF Master Lock WEIM CS2 Register"
|
|
bitfld.long 0x8 31. " WEMA2 ,WEIM CS2 Memory Active" "Not active,Active"
|
|
bitfld.long 0x8 3. " MLWE2_EN ,Master Lock WEIM CS2 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 0.--2. " MLWE2 ,Master Lock WEIM CS2 Access" "0,1,2,3,4,5,6,7"
|
|
line.long 0xC "M3IFMLWE3,M3IF Master Lock WEIM CS3 Register"
|
|
bitfld.long 0xC 31. " WEMA3 ,WEIM CS3 Memory Active" "Not active,Active"
|
|
bitfld.long 0xC 3. " MLWE3_EN ,Master Lock WEIM CS3 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 0.--2. " MLWE3 ,Master Lock WEIM CS3 Access" "0,1,2,3,4,5,6,7"
|
|
line.long 0x10 "M3IFMLWE4,M3IF Master Lock WEIM CS4 Register"
|
|
bitfld.long 0x10 31. " WEMA4 ,WEIM CS4 Memory Active" "Not active,Active"
|
|
bitfld.long 0x10 3. " MLWE4_EN ,Master Lock WEIM CS4 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 0.--2. " MLWE4 ,Master Lock WEIM CS4 Access" "0,1,2,3,4,5,6,7"
|
|
line.long 0x14 "M3IFMLWE5,M3IF Master Lock WEIM CS5 Register"
|
|
bitfld.long 0x14 31. " WEMA5 ,WEIM CS5 Memory Active" "Not active,Active"
|
|
bitfld.long 0x14 3. " MLWE5_EN ,Master Lock WEIM CS5 Access Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 0.--2. " MLWE5 ,Master Lock WEIM CS5 Access" "0,1,2,3,4,5,6,7"
|
|
width 0xb
|
|
tree.end
|
|
tree "NANDFC (NAND Flash Controller)"
|
|
base ad:0xbb001e00
|
|
width 23.
|
|
group.word 0x04++0x07
|
|
line.word 0x00 "RAM_BUFFER_ADDRESS,RAM Buffer Address Register"
|
|
bitfld.word 0x00 4.--5. " ACTIVE_CS ,Active Chip Select" "0,1,2,3"
|
|
bitfld.word 0x00 0.--2. " RBA ,RAM Buffer Address" "1st,2nd,3rd,4th,5th,6th,7th,8th"
|
|
line.word 0x02 "NAND_FLASH_ADDR,NAND Flash Address Register"
|
|
line.word 0x04 "NAND_FLASH_CMD,NAND Flash Command Register"
|
|
line.word 0x06 "NFC_CONFIGURATION,NFC Internal Buffer Lock Control Register"
|
|
bitfld.word 0x06 0.--1. " BLS ,Buffer Lock Set" "Locked,Locked,Unlocked,Locked"
|
|
rgroup.word 0x0c++0x3
|
|
line.word 0x00 "ECC_STATUS_RESULT1,Controller Status and Result of Flash Operation Register 1"
|
|
bitfld.word 0x00 12.--15. " NOSER4 ,Number of symbol errors for fourth 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
bitfld.word 0x00 8.--11. " NOSER3 ,Number of symbol errors for third 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
textline " "
|
|
bitfld.word 0x00 4.--7. " NOSER2 ,Number of symbol errors for second 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
bitfld.word 0x00 0.--3. " NOSER1 ,Number of symbol errors for first 528 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
line.word 0x02 "ECC_STATUS_RESULT2,Controller Status and Result of Flash Operation Register 2"
|
|
bitfld.word 0x02 12.--15. " NOSER8 ,Number of symbol errors for eighth 538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
bitfld.word 0x02 8.--11. " NOSER7 ,Number of symbol errors for seventh 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
textline " "
|
|
bitfld.word 0x02 4.--7. " NOSER6 ,Number of symbol errors for sixth 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
bitfld.word 0x02 0.--3. " NOSER5 ,Number of symbol errors for fifth 528/538 bytes" "No error,1-Symbol Error,2-Symbol Error,3-Symbol Error,4-Symbol Error,5-Symbol Error,6-Symbol Error,7-Symbol Error,8-Symbol Error,Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,Uncorrectable error"
|
|
group.word 0x10++0x3
|
|
line.word 0x00 "SPAS,SPare Area Size Register"
|
|
hexmask.word.byte 0x00 0.--7. 1. " SPAS ,Spare Area Size"
|
|
line.word 0x02 "NF_WR_PROT,Nand Flash Write Protection Register"
|
|
bitfld.word 0x02 0.--2. " WPC ,Write Protection Command" "Reserved,Lock-tight,Lock all,Reserved,Unlock,?..."
|
|
rgroup.word 0x18++0x01
|
|
line.word 0x00 "NAND_FLASH_WR_PR_ST,NAND Flash Write Protection Status Register"
|
|
bitfld.word 0x00 11. " US3 ,Unlocked Status " "No unlocked,Unlocked"
|
|
bitfld.word 0x00 10. " LS3 ,Locked Status" "No locked,Locked"
|
|
textline " "
|
|
bitfld.word 0x00 9. " LTS3 ,Lock-tight Status" "Not lock-tight,Lock-tight"
|
|
bitfld.word 0x00 8. " US2 ,Unlocked Status" "No unlocked,Unlocked"
|
|
textline " "
|
|
bitfld.word 0x00 7. " LS2 ,Locked Status" "No locked,Locked"
|
|
bitfld.word 0x00 6. " LTS2 ,Lock-tight Status" "Not lock-tight,Lock-tight"
|
|
textline " "
|
|
bitfld.word 0x00 5. " US1 ,Unlocked Status" "No unlocked,Unlocked"
|
|
bitfld.word 0x00 4. " LS1 ,Locked Status " "No locked,Locked"
|
|
textline " "
|
|
bitfld.word 0x00 3. " LTS1 ,Lock-tight Status" "Not lock-tight,Lock-tight"
|
|
bitfld.word 0x00 2. " US0 ,Unlocked Status" "No unlocked,Unlocked"
|
|
textline " "
|
|
bitfld.word 0x00 1. " LS0 ,Locked Status" "No locked,Locked"
|
|
bitfld.word 0x00 0. " LTS0 ,Lock-tight Status" "Not lock-tight,Lock-tight"
|
|
group.word 0x1a++0x03
|
|
line.word 0x00 "NAND_FLASH_CONFIG1,NAND Flash Operation Configuration Register"
|
|
bitfld.word 0x00 11. " FP_INT ,Full Page interrupt" "No interrupt,Interrupt"
|
|
bitfld.word 0x00 9.--10. " PPB ,Pages Per Block" "32,64,128,256"
|
|
textline " "
|
|
bitfld.word 0x00 8. " SYM ,Symmetric mode" "2,1"
|
|
bitfld.word 0x00 7. " NF_CE ,NAND Flash Force CE" "Normal,Forced 0"
|
|
textline " "
|
|
bitfld.word 0x00 6. " NFC_RST ,NFC Reset" "Not reset,Reset"
|
|
bitfld.word 0x00 5. " NF_BIG ,NAND FLASH Big Endian Mode" "Little endian,Big endian"
|
|
textline " "
|
|
bitfld.word 0x00 4. " INT_MASK ,Interrupt Mask" "Disabled,Enabled"
|
|
bitfld.word 0x00 3. " ECC_EN ,ECC Operation Enable" "Bypassed,Executed"
|
|
textline " "
|
|
bitfld.word 0x00 2. " SP_EN ,Spare Area Enable" "Main and spare,Spare only"
|
|
bitfld.word 0x00 1. " DMA_MODE ,Dma_req signal mode of operation during a page read" "Each section,End of a page"
|
|
textline " "
|
|
bitfld.word 0x00 0. " ECC_MODE ,ECC capabilities" "8,4"
|
|
line.word 0x02 "NAND_FLASH_CONFIG2,NAND Flash Operation Configuration 2 Register"
|
|
bitfld.word 0x02 15. " INT ,Interrupt" "Still running,Done"
|
|
textline " "
|
|
bitfld.word 0x02 3.--5. " FDO ,NAND Flash Data Output" "Reserved,One page,NAND Flash ID,Reserved,NAND Flash status,?..."
|
|
bitfld.word 0x02 2. " FDI ,NAND Flash Data Input" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x02 1. " FADD ,NAND Flash Address Input" "Disabled,Enabled"
|
|
bitfld.word 0x02 0. " FCMD ,NAND Flash Command Input" "Disabled,Enabled"
|
|
group.word 0x20++0x0f
|
|
line.word 0x00 "UNLOCK_START_BLK_ADD0,Address to Unlock in Write Protection Mode - Start"
|
|
line.word 0x02 "UNLOCK_END_BLK_ADD0,Address to Unlock in Write Protection Mode - End"
|
|
line.word 0x04 "UNLOCK_START_BLK_ADD1,Address to Unlock in Write Protection Mode - Start"
|
|
line.word 0x06 "UNLOCK_END_BLK_ADD1,Address to Unlock in Write Protection Mode - End"
|
|
line.word 0x08 "UNLOCK_START_BLK_ADD2,Address to Unlock in Write Protection Mode - Start"
|
|
line.word 0x0a "UNLOCK_END_BLK_ADD2,Address to Unlock in Write Protection Mode - End"
|
|
line.word 0x0c "UNLOCK_START_BLK_ADD3,Address to Unlock in Write Protection Mode - Start"
|
|
line.word 0x0e "UNLOCK_END_BLK_ADD3,Address to Unlock in Write Protection Mode - End"
|
|
width 0x16
|
|
tree.end
|
|
tree.open "WEIM (Wireless External Interface Module)"
|
|
base ad:0xb8002000
|
|
width 8.
|
|
tree "Registers Space"
|
|
if (((d.l(asd:0xB8002000))&0x200000)==0x0)
|
|
group.long (0x00+0x0)++0x3 "CS0"
|
|
line.long 0x00 "CSCR0U,Chip Select 0 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x0)++0x3 "CS0"
|
|
line.long 0x00 "CSCR0U,Chip Select 0 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002008))&0x8000)==0x0)
|
|
group.long (0x04+0x0)++0x3
|
|
line.long 0x00 "CSCR0L,Chip Select 0 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x0)++0x3
|
|
line.long 0x00 "CSCR0L,Chip Select 0 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002008))&0x8000)==0x0)
|
|
group.long (0x08+0x0)++0x3
|
|
line.long 0x00 "CSCR0A,Chip Select 0 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x0)++0x3
|
|
line.long 0x00 "CSCR0A,Chip Select 0 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
if (((d.l(asd:0xB8002010))&0x200000)==0x0)
|
|
group.long (0x00+0x10)++0x3 "CS1"
|
|
line.long 0x00 "CSCR1U,Chip Select 1 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x10)++0x3 "CS1"
|
|
line.long 0x00 "CSCR1U,Chip Select 1 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002018))&0x8000)==0x0)
|
|
group.long (0x04+0x10)++0x3
|
|
line.long 0x00 "CSCR1L,Chip Select 1 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x10)++0x3
|
|
line.long 0x00 "CSCR1L,Chip Select 1 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002018))&0x8000)==0x0)
|
|
group.long (0x08+0x10)++0x3
|
|
line.long 0x00 "CSCR1A,Chip Select 1 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x10)++0x3
|
|
line.long 0x00 "CSCR1A,Chip Select 1 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
if (((d.l(asd:0xB8002020))&0x200000)==0x0)
|
|
group.long (0x00+0x20)++0x3 "CS2"
|
|
line.long 0x00 "CSCR2U,Chip Select 2 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x20)++0x3 "CS2"
|
|
line.long 0x00 "CSCR2U,Chip Select 2 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002028))&0x8000)==0x0)
|
|
group.long (0x04+0x20)++0x3
|
|
line.long 0x00 "CSCR2L,Chip Select 2 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x20)++0x3
|
|
line.long 0x00 "CSCR2L,Chip Select 2 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002028))&0x8000)==0x0)
|
|
group.long (0x08+0x20)++0x3
|
|
line.long 0x00 "CSCR2A,Chip Select 2 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x20)++0x3
|
|
line.long 0x00 "CSCR2A,Chip Select 2 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
if (((d.l(asd:0xB8002030))&0x200000)==0x0)
|
|
group.long (0x00+0x30)++0x3 "CS3"
|
|
line.long 0x00 "CSCR3U,Chip Select 3 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x30)++0x3 "CS3"
|
|
line.long 0x00 "CSCR3U,Chip Select 3 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002038))&0x8000)==0x0)
|
|
group.long (0x04+0x30)++0x3
|
|
line.long 0x00 "CSCR3L,Chip Select 3 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x30)++0x3
|
|
line.long 0x00 "CSCR3L,Chip Select 3 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002038))&0x8000)==0x0)
|
|
group.long (0x08+0x30)++0x3
|
|
line.long 0x00 "CSCR3A,Chip Select 3 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x30)++0x3
|
|
line.long 0x00 "CSCR3A,Chip Select 3 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
if (((d.l(asd:0xB8002040))&0x200000)==0x0)
|
|
group.long (0x00+0x40)++0x3 "CS4"
|
|
line.long 0x00 "CSCR4U,Chip Select 4 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x40)++0x3 "CS4"
|
|
line.long 0x00 "CSCR4U,Chip Select 4 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002048))&0x8000)==0x0)
|
|
group.long (0x04+0x40)++0x3
|
|
line.long 0x00 "CSCR4L,Chip Select 4 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x40)++0x3
|
|
line.long 0x00 "CSCR4L,Chip Select 4 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002048))&0x8000)==0x0)
|
|
group.long (0x08+0x40)++0x3
|
|
line.long 0x00 "CSCR4A,Chip Select 4 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x40)++0x3
|
|
line.long 0x00 "CSCR4A,Chip Select 4 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
if (((d.l(asd:0xB8002050))&0x200000)==0x0)
|
|
group.long (0x00+0x50)++0x3 "CS5"
|
|
line.long 0x00 "CSCR5U,Chip Select 5 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,Continuous"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
else
|
|
group.long (0x00+0x50)++0x3 "CS5"
|
|
line.long 0x00 "CSCR5U,Chip Select 5 Upper Control Register"
|
|
bitfld.long 0x00 31. " SP ,Supervisor Protect" "Not protected,Protected"
|
|
bitfld.long 0x00 30. " WP ,Write Protect" "Not protected,Protected"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " BCD ,Burst Clock Divisor" "1,2,3,4"
|
|
bitfld.long 0x00 24.--27. " BCS ,Burst Clock Start" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PSZ ,Page Size" "4,8,16,32"
|
|
bitfld.long 0x00 21. " PME ,Page Mode Emulation" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " SYNC ,Synchronous Burst Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " DOL ,Data Output Length" "1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,1 cycles/Fixed write latency,2 cycles/Fixed write latency,3 cycles/Fixed write latency,4 cycles/Fixed write latency,5 cycles/Fixed write latency,6 cycles/Fixed write latency,7 cycles/Fixed write latency,8 cycles/Fixed write latency"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " CNC ,Chip Select Negation Clock Cycles" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
hexmask.long.byte 0x00 8.--13. 1. " WSC ,Wait State Control"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EW ,/ECB|WAIT" "Low,High"
|
|
bitfld.long 0x00 4.--6. " WWS ,Write Wait State" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " EDC ,Extra Dead Cycles" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
endif
|
|
if (((d.l(asd:0xB8002058))&0x8000)==0x0)
|
|
group.long (0x04+0x50)++0x3
|
|
line.long 0x00 "CSCR5L,Chip Select 5 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,DATA_IN/OUT [15:8] pins,DATA_IN/OUT [7:0] pins,Reserved,DATA_IN/OUT [15:0] pins,Reserved,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
else
|
|
group.long (0x04+0x50)++0x3
|
|
line.long 0x00 "CSCR5L,Chip Select 5 Lower Control Register"
|
|
bitfld.long 0x00 28.--31. " OEA ,/OE Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " OEN ,/OE Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " EBWA ,Enable Byte Write Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " EBWN ,Enable Byte Write Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " CSA ,Chip Select Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 11. " EBC ,Enable Byte Control" "Read/Write,Write"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " DSZ ,Data Port Size" "Reserved,Reserved,Reserved,Reserved,Reserved,Reserved,ADDR / M_DATA_IN/OUT [31:0]| M_DATA_IN/OUT [31:16] pins,Same"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " CSN ,Chip Select Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 3. " PSR ,Pseudo SRAM Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " CRE ,Control Register Enable" "Pin 0,Pin 1"
|
|
bitfld.long 0x00 1. " WRAP ,WRAP memory mode" "No wrap,Wrap"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSEN ,Chip Select Enable" "Disabled,Enabled"
|
|
endif
|
|
if (((d.l(asd:0xB8002058))&0x8000)==0x0)
|
|
group.long (0x08+0x50)++0x3
|
|
line.long 0x00 "CSCR5A,Chip Select 5 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
else
|
|
group.long (0x08+0x50)++0x3
|
|
line.long 0x00 "CSCR5A,Chip Select 5 Addition Control Register"
|
|
bitfld.long 0x00 28.--31. " EBRA ,Enable Byte Read Assert" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 24.--27. " EBRN ,Enable Byte Read Negate" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " RWA ,Read/Write Assertion" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
bitfld.long 0x00 16.--19. " RWN ,Read/Write Negation" "0 cycles,1 cycle,2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 15. " MUM ,Multiplexed Mode" "Non-multiplexed,Multiplexed"
|
|
bitfld.long 0x00 13.--14. " LAH ,/LBA to Address Hold" "2 cycles,13 cycles,24 cycles,35 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 10.--12. " LBN ,/LBA Negation" "2 cycles,3 cycles,4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles"
|
|
bitfld.long 0x00 8.--9. " LBA ,/LBA Assertion" "0 cycles,1 cycle,2 cycles,3 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DWW ,Decrease Write Wait State" "0,1,2,3"
|
|
bitfld.long 0x00 4.--5. " DCT ,/DTACK Check Time" "2 cycles,6 cycles,8 cycles,12 cycles"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WWU ,Write Wrap Unmask" "Masked,Unmasked"
|
|
bitfld.long 0x00 2. " AGE ,Acknowledge Glue Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CNC2 ,Chip Select Negation Clock Cycles" "Low,High"
|
|
bitfld.long 0x00 0. " FCE ,Feedback Clock Enable" "AHB clock,BCLK_FB"
|
|
endif
|
|
textline ""
|
|
textline ""
|
|
width 5.
|
|
group.long 0x60++0x3
|
|
line.long 0x00 "WCR,WEIM Configuration Register"
|
|
bitfld.long 0x00 19. " ECP5 ,/ECB Capture Phase 5" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 18. " ECP4 ,/ECB Capture Phase 4" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 17. " ECP3 ,/ECB Capture Phase 3" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 16. " ECP2 ,/ECB Capture Phase 2" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 15. " ECP1 ,/ECB Capture Phase 1" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 14. " ECP0 ,/ECB Capture Phase 0" "BCS[0],Opposite BCS[0] for write only"
|
|
textline " "
|
|
bitfld.long 0x00 13. " AUS5 ,Address Unshifted for CS5" "Shifted,Unshifted"
|
|
bitfld.long 0x00 12. " AUS4 ,Address Unshifted for CS4" "Shifted,Unshifted"
|
|
textline " "
|
|
bitfld.long 0x00 11. " AUS3 ,Address Unshifted for CS3" "Shifted,Unshifted"
|
|
bitfld.long 0x00 10. " AUS2 ,Address Unshifted for CS2" "Shifted,Unshifted"
|
|
textline " "
|
|
bitfld.long 0x00 9. " AUS1 ,Address Unshifted for CS1" "Shifted,Unshifted"
|
|
bitfld.long 0x00 8. " AUS0 ,Address Unshifted for CS0" "Shifted,Unshifted"
|
|
textline " "
|
|
bitfld.long 0x00 2. " BCM ,Burst Clock Mode" "CS accessing,All time"
|
|
bitfld.long 0x00 1. " CRER ,CRE output Relocation" "ADDR[23],ADDR[25]"
|
|
textline " "
|
|
bitfld.long 0x00 0. " MAS ,Merged Address Mode" "Standard,Merged"
|
|
tree.end
|
|
tree "Memory"
|
|
width 5.
|
|
base asd:0xa0000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS0,WEIM CS0 Memory Region"
|
|
button "CS0 " "d asd:0xa0000000--asd:0xa7ffffff /long"
|
|
base asd:0xa8000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS1,WEIM CS1 Memory Region"
|
|
button "CS1 " "d asd:0xa8000000--asd:0xafffffff /long"
|
|
base asd:0xb0000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS2,WEIM CS2 Memory Region"
|
|
button "CS2 " "d asd:0xb0000000--asd:0xb1ffffff /long"
|
|
base asd:0xb2000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS3,WEIM CS3 Memory Region"
|
|
button "CS3 " "d asd:0xb2000000--asd:0xb3ffffff /long"
|
|
base asd:0xb4000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS4,WEIM CS4 Memory Region"
|
|
button "CS4 " "d asd:0xb4000000--asd:0xb5ffffff /long"
|
|
base asd:0xb6000000
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CS5,WEIM CS5 Memory Region"
|
|
button "CS5 " "d asd:0xb6000000--asd:0xb7ffffff /long"
|
|
tree.end
|
|
tree.end
|
|
tree.end
|
|
tree "1-Wire"
|
|
base ad:0x43F9C000
|
|
width 14.
|
|
group.byte 0x00++0x1
|
|
line.word 0x00 "CONTROL,Control Register"
|
|
bitfld.word 0x00 7. " RPP ,Reset Presence Pulse" "Reset,Not completed"
|
|
bitfld.word 0x00 6. " PST ,Presence Status" "Not present,Present"
|
|
bitfld.word 0x00 5. " WR0 ,Write 0" "Written,Not completed"
|
|
textline " "
|
|
bitfld.word 0x00 4. " WR1 ,Write 1 / Read" "Completed,Not completed"
|
|
bitfld.word 0x00 3. " RDST ,Read Status" "0,1"
|
|
group.byte 0x02++0x1
|
|
line.word 0x00 "TIME_DIVIDER,Time Divider Register"
|
|
hexmask.word.byte 0x00 0.--7. 1. " DVDR ,Divider Factor"
|
|
group.byte 0x04++0x1
|
|
line.word 0x00 "RESET,Reset Register"
|
|
bitfld.word 0x00 0. " RST ,Software Reset" "No reset,Reset"
|
|
group.byte 0x06++0x1
|
|
line.word 0x0 "COMMAND,Command Register"
|
|
bitfld.word 0x0 1. " SRA ,Search ROM Accelerator" "Disabled,Enabled"
|
|
hgroup.byte 0x8++0x1
|
|
hide.word 0x0 "TX/RX,Transmit/Receive Register"
|
|
in
|
|
hgroup.byte 0xA++0x1
|
|
hide.word 0x0 "INTERRUPT,Interrupt Register"
|
|
in
|
|
group.byte 0xC++0x1
|
|
line.word 0x0 "INTERRUPT_EN,Interrupt Enable Register"
|
|
bitfld.word 0x00 5. " ERSF ,Enable Receive Shift Register Full Interrupt" "Disabled,Enabled"
|
|
bitfld.word 0x00 4. " ERBF ,Enable Receive Buffer Full Interrupt" "Disabled,Enabled"
|
|
bitfld.word 0x00 3. " ETSE ,Enable Transmit Shift Register Empty Interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 2. " ETBE ,Enable Transmit Buffer Empty Interrupt" "Disabled,Enabled"
|
|
bitfld.word 0x00 1. " IAS ,Interrupt Trigger Active State" "High,Low"
|
|
bitfld.word 0x00 0. " EPD ,Enable Presence Detect" "Disabled,Enabled"
|
|
width 0xb
|
|
tree.end
|
|
tree "ATA (Advanced Technology Attachment)"
|
|
base ad:0x50020000
|
|
width 18.
|
|
tree "Timing Registers"
|
|
group.byte 0x00--0x18
|
|
line.byte 0x00 "TIME_OFF,TIME OFF Register"
|
|
line.byte 0x01 "TIME_ON,TIME ON Register"
|
|
line.byte 0x02 "TIME_1,TIME 1 Register"
|
|
line.byte 0x03 "TIME_2W,TIME 2W Register"
|
|
line.byte 0x04 "TIME_2R,TIME 2R Register"
|
|
line.byte 0x05 "TIME_AX,TIME AX Register"
|
|
line.byte 0x06 "TIME_PIO_RDX,TIME PIO RDX Register"
|
|
line.byte 0x07 "TIME_4,TIME 4 Register"
|
|
line.byte 0x08 "TIME_9,TIME 9 Register"
|
|
line.byte 0x09 "TIME_M,TIME M Register"
|
|
line.byte 0x0a "TIME_JN,TIME JN Register"
|
|
line.byte 0x0b "TIME_D,TIME D Register"
|
|
line.byte 0x0c "TIME_K,TIME K Register"
|
|
line.byte 0x0d "TIME_ACK,TIME ACK Register"
|
|
line.byte 0x0e "TIME_ENV,TIME ENV Register"
|
|
line.byte 0x0f "TIME_RPX,TIME RPX Register"
|
|
line.byte 0x10 "TIME_ZAH,TIME ZAH Register"
|
|
line.byte 0x11 "TIME_MLIX,TIME MLIX Register"
|
|
line.byte 0x12 "TIME_DVH,TIME DVH Register"
|
|
line.byte 0x13 "TIME_DZFS,TIME DZFS Register"
|
|
line.byte 0x14 "TIME_DVS,TIME DVS Register"
|
|
line.byte 0x15 "TIME_CVH,Time CVH Register"
|
|
line.byte 0x16 "TIME_SS,TIME SS Register"
|
|
line.byte 0x17 "TIME_CYC,TIME CYC Register"
|
|
tree.end
|
|
width 20.
|
|
hgroup.word 0x1c++0x01
|
|
hide.word 0x00 "FIFO_DATA_16,FIFO DATA Register In 16-bit Mode"
|
|
in
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "FIFO_DATA_32,FIFO_DATA Register In 32-bit Mode"
|
|
in
|
|
rgroup.byte 0x20++0x00
|
|
line.byte 0x00 "FIFO_FILL,FIFO_FILL Register"
|
|
group.word 0x24++0x01
|
|
line.word 0x00 "ATA_CONTROL,ATA Control Register"
|
|
bitfld.word 0x00 12. " DMA_SRST ,Internal DMA controller is in reset or enabled" "Normal,Reset"
|
|
textline " "
|
|
bitfld.word 0x00 10.--11. " DMA_SELECT ,DMA mode selected" "Single DMA,32-bit ADMA,64-bit ADMA,?..."
|
|
textline " "
|
|
bitfld.word 0x00 9. " DMA_START_STOP ,DMA master start or stop" "Stopped,Started"
|
|
textline " "
|
|
bitfld.word 0x00 8. " DMA_ENABLE ,DMA master enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 7. " FIFO_RST_B ,Controls the internal FIFO reset" "Reset,Normal"
|
|
textline " "
|
|
bitfld.word 0x00 6. " ATA_RST_B ,Controls the level on the ata_reset_b pin" "Reset,Normal"
|
|
textline " "
|
|
bitfld.word 0x00 5. " FIFO_TX_EN ,FIFO Transmit Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 4. " FIFO_RCV_EN ,FIFO Receive Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 3. " DMA_PENDING ,DMA Pending Bit" "Not start,Start"
|
|
textline " "
|
|
bitfld.word 0x00 2. " DMA_ULTRA_SELECTED ,UDMA Or MDMA Protocol Is used" "MDMA,UDMA"
|
|
textline " "
|
|
bitfld.word 0x00 1. " DMA_WRITE ,Data Direction On Any DMA" "In burst,Out burst"
|
|
textline " "
|
|
bitfld.word 0x00 0. " IORDY_EN ,IORDY Handshake Or Disregarded" "Disregarded,Handshake"
|
|
rgroup.byte 0x28++0x00
|
|
line.byte 0x00 "INT_PENDING,Interrupt Pending Register"
|
|
bitfld.byte 0x00 7. " ATA_INTRQ1 ,ATA Interrupt Request 1" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.byte 0x00 6. " FIFO_UNDERFLOW ,FIFO Underflow" "No underflow,Underflow"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FIFO_OVERFLOW ,FIFO Overflow" "No overflow,Overflow"
|
|
textline " "
|
|
bitfld.byte 0x00 4. " CONTROLLER_IDLE ,Controller Idle" "Active,Idle"
|
|
textline " "
|
|
bitfld.byte 0x00 3. " ATA_INTRQ2 ,ATA interrupt request 2" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.byte 0x00 2. " DMA_ERR ,Dma error" "No error,Error"
|
|
textline " "
|
|
bitfld.byte 0x00 1. " DMA_TRANS_OVER ,Dma transfer over" "Not finished,Finished"
|
|
group.byte 0x2c++0x00
|
|
line.byte 0x00 "INT_ENABLE,Interrupt_Enable Register"
|
|
bitfld.byte 0x00 7. " ATA_INTRQ1 ,ATA Interrupt Request 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 6. " FIFO_UNDERFLOW ,FIFO Underflow" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FIFO_OVERFLOW ,FIFO Overflow" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 4. " CONTROLLER_IDLE ,Controller Idle" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 3. " ATA_INTRQ2 ,ATA Interrupt Request 2" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 2. " DMA_ERR ,Dma error" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.byte 0x00 1. " DMA_TRANS_OVER ,Dma transfer over" "Disabled,Enabled"
|
|
wgroup.byte 0x30++0x00
|
|
line.byte 0x00 "INTERRUPT_CLEAR,Interrupt Clear Register"
|
|
bitfld.byte 0x00 6. " FIFO_UNDERFLOW ,FIFO Underflow Interrupt Clear" "Not clear,Clear"
|
|
textline " "
|
|
bitfld.byte 0x00 5. " FIFO_OVERFLOW ,FIFO Overflow Interrupt Clear" "Not clear,Clear"
|
|
textline " "
|
|
bitfld.byte 0x00 2. " DMA_ERR ,Dma error Interrupt Clear" "Not clear,Clear"
|
|
textline " "
|
|
bitfld.byte 0x00 1. " DMA_TRANS_OVER ,Dma transfer over Interrupt Clear" "Not clear,Clear"
|
|
group.byte 0x34++0x00
|
|
line.byte 0x00 "FIFO_ALARM,FIFO Alarm Register"
|
|
group.byte 0x38++0x00
|
|
line.byte 0x00 "ADMA_ERR_STATUS,ADMA Error States Register"
|
|
bitfld.byte 0x00 2. " ADMA_LEN_MISMATCH ,ADMA length mismatch" "No error,Error"
|
|
textline " "
|
|
bitfld.byte 0x00 0.--1. " ADMA_ERR_STATE ,ADMA error state" "ST_STOP,ST_FDS,ST_CARD,ST_TFR"
|
|
group.long 0x3C++0x03
|
|
line.long 0x00 "SYS_DMA_BADDR,Single DMA Transfer Start Base Address Register"
|
|
group.long 0x40++0x3
|
|
line.long 0x00 "ADMA_SYS_ADDR,ADMA Descriptor Table Start Address Register"
|
|
group.word 0x48++0x01
|
|
line.word 0x00 "BLOCK_CNT,Block count Register"
|
|
group.byte 0x4C++0x0
|
|
line.byte 0x00 "BURST_LENGTH,Burst length Register"
|
|
bitfld.byte 0x00 0.--5. " BURST_LENGTH ,Burst length" "Reserved,1 words,2 words,2 words,4 words,4 words,4 words,4 words,8 words,8 words,8 words,8 words,8 words,8 words,8 words,8 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,16 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words,32 words"
|
|
group.byte 0x50++0x00
|
|
line.byte 0x00 "SECTOR_SIZE,Sector Size Register"
|
|
group.word 0xa0++0x01 "Drive Registers"
|
|
line.word 0x00 "DRIVE_DATA,Drive Data Register"
|
|
group.byte 0xa4++0x00
|
|
line.byte 0x00 "DRIVE_FEATURES,Drive Features Register"
|
|
group.byte 0xa8++0x00
|
|
line.byte 0x00 "DRIVE_SECTOR_COUNT,Drive Sector Count Register"
|
|
group.byte 0xac++0x00
|
|
line.byte 0x00 "DRIVE_SECTOR_NUM,Drive Sector Number Register"
|
|
group.byte 0xb0++0x00
|
|
line.byte 0x00 "DRIVE_CYL_LOW,Drive Cylinder Low Register"
|
|
group.byte 0xb4++0x00
|
|
line.byte 0x00 "DRIVE_CYL_HIGH,Drive Cylinder High Register"
|
|
group.byte 0xb8++0x00
|
|
line.byte 0x00 "DRIVE_DEV_HEAD,Drive Device Head Register"
|
|
wgroup.byte 0xbc++0x00
|
|
line.byte 0x00 "DRIVE_COMMAND,Drive Command Register"
|
|
rgroup.byte 0xbc++0x00
|
|
line.byte 0x00 "DRIVE_STATUS,Drive Status Register"
|
|
rgroup.byte 0xc8++0x00
|
|
line.byte 0x00 "DRIVE_ALT_STATUS,Drive Alternate Status Register"
|
|
wgroup.byte 0xc8++0x00
|
|
line.byte 0x00 "DRIVE_CONTROL,Drive Control Register"
|
|
width 0xb
|
|
tree.end
|
|
tree.open "FlexCAN (Controller Area Network)"
|
|
tree "CAN 1"
|
|
base ad:0x53FE4000
|
|
width 12.
|
|
tree "Message Buffer Registers 0-15"
|
|
group.long (0x0080+0x0)++0x03 "Message Buffer Register 0"
|
|
line.long 0x00 "C/S0,Control and Status 0"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x0)++0x03
|
|
line.long 0x00 "ID0,Identifier Field 0"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x0)++0x03
|
|
line.long 0x00 "ID0,Identifier Field 0"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x0)++0x07
|
|
line.long 0x00 "DATA0-3_0,Data Field 0-3 0"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_0,Data Field 4-7 0"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x10)++0x03 "Message Buffer Register 1"
|
|
line.long 0x00 "C/S1,Control and Status 1"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x10)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x10)++0x03
|
|
line.long 0x00 "ID1,Identifier Field 1"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x10)++0x03
|
|
line.long 0x00 "ID1,Identifier Field 1"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x10)++0x07
|
|
line.long 0x00 "DATA0-3_1,Data Field 0-3 1"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_1,Data Field 4-7 1"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x20)++0x03 "Message Buffer Register 2"
|
|
line.long 0x00 "C/S2,Control and Status 2"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x20)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x20)++0x03
|
|
line.long 0x00 "ID2,Identifier Field 2"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x20)++0x03
|
|
line.long 0x00 "ID2,Identifier Field 2"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x20)++0x07
|
|
line.long 0x00 "DATA0-3_2,Data Field 0-3 2"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_2,Data Field 4-7 2"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x30)++0x03 "Message Buffer Register 3"
|
|
line.long 0x00 "C/S3,Control and Status 3"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x30)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x30)++0x03
|
|
line.long 0x00 "ID3,Identifier Field 3"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x30)++0x03
|
|
line.long 0x00 "ID3,Identifier Field 3"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x30)++0x07
|
|
line.long 0x00 "DATA0-3_3,Data Field 0-3 3"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_3,Data Field 4-7 3"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x40)++0x03 "Message Buffer Register 4"
|
|
line.long 0x00 "C/S4,Control and Status 4"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x40)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x40)++0x03
|
|
line.long 0x00 "ID4,Identifier Field 4"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x40)++0x03
|
|
line.long 0x00 "ID4,Identifier Field 4"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x40)++0x07
|
|
line.long 0x00 "DATA0-3_4,Data Field 0-3 4"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_4,Data Field 4-7 4"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x50)++0x03 "Message Buffer Register 5"
|
|
line.long 0x00 "C/S5,Control and Status 5"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x50)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x50)++0x03
|
|
line.long 0x00 "ID5,Identifier Field 5"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x50)++0x03
|
|
line.long 0x00 "ID5,Identifier Field 5"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x50)++0x07
|
|
line.long 0x00 "DATA0-3_5,Data Field 0-3 5"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_5,Data Field 4-7 5"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x60)++0x03 "Message Buffer Register 6"
|
|
line.long 0x00 "C/S6,Control and Status 6"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x60)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x60)++0x03
|
|
line.long 0x00 "ID6,Identifier Field 6"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x60)++0x03
|
|
line.long 0x00 "ID6,Identifier Field 6"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x60)++0x07
|
|
line.long 0x00 "DATA0-3_6,Data Field 0-3 6"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_6,Data Field 4-7 6"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x70)++0x03 "Message Buffer Register 7"
|
|
line.long 0x00 "C/S7,Control and Status 7"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x70)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x70)++0x03
|
|
line.long 0x00 "ID7,Identifier Field 7"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x70)++0x03
|
|
line.long 0x00 "ID7,Identifier Field 7"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x70)++0x07
|
|
line.long 0x00 "DATA0-3_7,Data Field 0-3 7"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_7,Data Field 4-7 7"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x80)++0x03 "Message Buffer Register 8"
|
|
line.long 0x00 "C/S8,Control and Status 8"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x80)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x80)++0x03
|
|
line.long 0x00 "ID8,Identifier Field 8"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x80)++0x03
|
|
line.long 0x00 "ID8,Identifier Field 8"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x80)++0x07
|
|
line.long 0x00 "DATA0-3_8,Data Field 0-3 8"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_8,Data Field 4-7 8"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x90)++0x03 "Message Buffer Register 9"
|
|
line.long 0x00 "C/S9,Control and Status 9"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x90)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x90)++0x03
|
|
line.long 0x00 "ID9,Identifier Field 9"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x90)++0x03
|
|
line.long 0x00 "ID9,Identifier Field 9"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x90)++0x07
|
|
line.long 0x00 "DATA0-3_9,Data Field 0-3 9"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_9,Data Field 4-7 9"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xA0)++0x03 "Message Buffer Register 10"
|
|
line.long 0x00 "C/S10,Control and Status 10"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xA0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xA0)++0x03
|
|
line.long 0x00 "ID10,Identifier Field 10"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xA0)++0x03
|
|
line.long 0x00 "ID10,Identifier Field 10"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xA0)++0x07
|
|
line.long 0x00 "DATA0-3_10,Data Field 0-3 10"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_10,Data Field 4-7 10"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xB0)++0x03 "Message Buffer Register 11"
|
|
line.long 0x00 "C/S11,Control and Status 11"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xB0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xB0)++0x03
|
|
line.long 0x00 "ID11,Identifier Field 11"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xB0)++0x03
|
|
line.long 0x00 "ID11,Identifier Field 11"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xB0)++0x07
|
|
line.long 0x00 "DATA0-3_11,Data Field 0-3 11"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_11,Data Field 4-7 11"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xC0)++0x03 "Message Buffer Register 12"
|
|
line.long 0x00 "C/S12,Control and Status 12"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xC0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xC0)++0x03
|
|
line.long 0x00 "ID12,Identifier Field 12"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xC0)++0x03
|
|
line.long 0x00 "ID12,Identifier Field 12"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xC0)++0x07
|
|
line.long 0x00 "DATA0-3_12,Data Field 0-3 12"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_12,Data Field 4-7 12"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xD0)++0x03 "Message Buffer Register 13"
|
|
line.long 0x00 "C/S13,Control and Status 13"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xD0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xD0)++0x03
|
|
line.long 0x00 "ID13,Identifier Field 13"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xD0)++0x03
|
|
line.long 0x00 "ID13,Identifier Field 13"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xD0)++0x07
|
|
line.long 0x00 "DATA0-3_13,Data Field 0-3 13"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_13,Data Field 4-7 13"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xE0)++0x03 "Message Buffer Register 14"
|
|
line.long 0x00 "C/S14,Control and Status 14"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xE0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xE0)++0x03
|
|
line.long 0x00 "ID14,Identifier Field 14"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xE0)++0x03
|
|
line.long 0x00 "ID14,Identifier Field 14"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xE0)++0x07
|
|
line.long 0x00 "DATA0-3_14,Data Field 0-3 14"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_14,Data Field 4-7 14"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xF0)++0x03 "Message Buffer Register 15"
|
|
line.long 0x00 "C/S15,Control and Status 15"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0xF0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xF0)++0x03
|
|
line.long 0x00 "ID15,Identifier Field 15"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xF0)++0x03
|
|
line.long 0x00 "ID15,Identifier Field 15"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xF0)++0x07
|
|
line.long 0x00 "DATA0-3_15,Data Field 0-3 15"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_15,Data Field 4-7 15"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 16-31"
|
|
group.long (0x0080+0x100)++0x03 "Message Buffer Register 16"
|
|
line.long 0x00 "C/S16,Control and Status 16"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x100)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x100)++0x03
|
|
line.long 0x00 "ID16,Identifier Field 16"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x100)++0x03
|
|
line.long 0x00 "ID16,Identifier Field 16"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x100)++0x07
|
|
line.long 0x00 "DATA0-3_16,Data Field 0-3 16"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_16,Data Field 4-7 16"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x110)++0x03 "Message Buffer Register 17"
|
|
line.long 0x00 "C/S17,Control and Status 17"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x110)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x110)++0x03
|
|
line.long 0x00 "ID17,Identifier Field 17"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x110)++0x03
|
|
line.long 0x00 "ID17,Identifier Field 17"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x110)++0x07
|
|
line.long 0x00 "DATA0-3_17,Data Field 0-3 17"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_17,Data Field 4-7 17"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x120)++0x03 "Message Buffer Register 18"
|
|
line.long 0x00 "C/S18,Control and Status 18"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x120)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x120)++0x03
|
|
line.long 0x00 "ID18,Identifier Field 18"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x120)++0x03
|
|
line.long 0x00 "ID18,Identifier Field 18"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x120)++0x07
|
|
line.long 0x00 "DATA0-3_18,Data Field 0-3 18"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_18,Data Field 4-7 18"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x130)++0x03 "Message Buffer Register 19"
|
|
line.long 0x00 "C/S19,Control and Status 19"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x130)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x130)++0x03
|
|
line.long 0x00 "ID19,Identifier Field 19"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x130)++0x03
|
|
line.long 0x00 "ID19,Identifier Field 19"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x130)++0x07
|
|
line.long 0x00 "DATA0-3_19,Data Field 0-3 19"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_19,Data Field 4-7 19"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x140)++0x03 "Message Buffer Register 20"
|
|
line.long 0x00 "C/S20,Control and Status 20"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x140)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x140)++0x03
|
|
line.long 0x00 "ID20,Identifier Field 20"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x140)++0x03
|
|
line.long 0x00 "ID20,Identifier Field 20"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x140)++0x07
|
|
line.long 0x00 "DATA0-3_20,Data Field 0-3 20"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_20,Data Field 4-7 20"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x150)++0x03 "Message Buffer Register 21"
|
|
line.long 0x00 "C/S21,Control and Status 21"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x150)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x150)++0x03
|
|
line.long 0x00 "ID21,Identifier Field 21"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x150)++0x03
|
|
line.long 0x00 "ID21,Identifier Field 21"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x150)++0x07
|
|
line.long 0x00 "DATA0-3_21,Data Field 0-3 21"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_21,Data Field 4-7 21"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x160)++0x03 "Message Buffer Register 22"
|
|
line.long 0x00 "C/S22,Control and Status 22"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x160)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x160)++0x03
|
|
line.long 0x00 "ID22,Identifier Field 22"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x160)++0x03
|
|
line.long 0x00 "ID22,Identifier Field 22"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x160)++0x07
|
|
line.long 0x00 "DATA0-3_22,Data Field 0-3 22"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_22,Data Field 4-7 22"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x170)++0x03 "Message Buffer Register 23"
|
|
line.long 0x00 "C/S23,Control and Status 23"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x170)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x170)++0x03
|
|
line.long 0x00 "ID23,Identifier Field 23"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x170)++0x03
|
|
line.long 0x00 "ID23,Identifier Field 23"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x170)++0x07
|
|
line.long 0x00 "DATA0-3_23,Data Field 0-3 23"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_23,Data Field 4-7 23"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x180)++0x03 "Message Buffer Register 24"
|
|
line.long 0x00 "C/S24,Control and Status 24"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x180)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x180)++0x03
|
|
line.long 0x00 "ID24,Identifier Field 24"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x180)++0x03
|
|
line.long 0x00 "ID24,Identifier Field 24"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x180)++0x07
|
|
line.long 0x00 "DATA0-3_24,Data Field 0-3 24"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_24,Data Field 4-7 24"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x190)++0x03 "Message Buffer Register 25"
|
|
line.long 0x00 "C/S25,Control and Status 25"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x190)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x190)++0x03
|
|
line.long 0x00 "ID25,Identifier Field 25"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x190)++0x03
|
|
line.long 0x00 "ID25,Identifier Field 25"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x190)++0x07
|
|
line.long 0x00 "DATA0-3_25,Data Field 0-3 25"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_25,Data Field 4-7 25"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1A0)++0x03 "Message Buffer Register 26"
|
|
line.long 0x00 "C/S26,Control and Status 26"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1A0)++0x03
|
|
line.long 0x00 "ID26,Identifier Field 26"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1A0)++0x03
|
|
line.long 0x00 "ID26,Identifier Field 26"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1A0)++0x07
|
|
line.long 0x00 "DATA0-3_26,Data Field 0-3 26"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_26,Data Field 4-7 26"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1B0)++0x03 "Message Buffer Register 27"
|
|
line.long 0x00 "C/S27,Control and Status 27"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1B0)++0x03
|
|
line.long 0x00 "ID27,Identifier Field 27"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1B0)++0x03
|
|
line.long 0x00 "ID27,Identifier Field 27"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1B0)++0x07
|
|
line.long 0x00 "DATA0-3_27,Data Field 0-3 27"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_27,Data Field 4-7 27"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1C0)++0x03 "Message Buffer Register 28"
|
|
line.long 0x00 "C/S28,Control and Status 28"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1C0)++0x03
|
|
line.long 0x00 "ID28,Identifier Field 28"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1C0)++0x03
|
|
line.long 0x00 "ID28,Identifier Field 28"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1C0)++0x07
|
|
line.long 0x00 "DATA0-3_28,Data Field 0-3 28"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_28,Data Field 4-7 28"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1D0)++0x03 "Message Buffer Register 29"
|
|
line.long 0x00 "C/S29,Control and Status 29"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1D0)++0x03
|
|
line.long 0x00 "ID29,Identifier Field 29"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1D0)++0x03
|
|
line.long 0x00 "ID29,Identifier Field 29"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1D0)++0x07
|
|
line.long 0x00 "DATA0-3_29,Data Field 0-3 29"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_29,Data Field 4-7 29"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1E0)++0x03 "Message Buffer Register 30"
|
|
line.long 0x00 "C/S30,Control and Status 30"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1E0)++0x03
|
|
line.long 0x00 "ID30,Identifier Field 30"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1E0)++0x03
|
|
line.long 0x00 "ID30,Identifier Field 30"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1E0)++0x07
|
|
line.long 0x00 "DATA0-3_30,Data Field 0-3 30"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_30,Data Field 4-7 30"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1F0)++0x03 "Message Buffer Register 31"
|
|
line.long 0x00 "C/S31,Control and Status 31"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x1F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1F0)++0x03
|
|
line.long 0x00 "ID31,Identifier Field 31"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1F0)++0x03
|
|
line.long 0x00 "ID31,Identifier Field 31"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1F0)++0x07
|
|
line.long 0x00 "DATA0-3_31,Data Field 0-3 31"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_31,Data Field 4-7 31"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 32-47"
|
|
group.long (0x0080+0x200)++0x03 "Message Buffer Register 32"
|
|
line.long 0x00 "C/S32,Control and Status 32"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x200)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x200)++0x03
|
|
line.long 0x00 "ID32,Identifier Field 32"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x200)++0x03
|
|
line.long 0x00 "ID32,Identifier Field 32"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x200)++0x07
|
|
line.long 0x00 "DATA0-3_32,Data Field 0-3 32"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_32,Data Field 4-7 32"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x210)++0x03 "Message Buffer Register 33"
|
|
line.long 0x00 "C/S33,Control and Status 33"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x210)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x210)++0x03
|
|
line.long 0x00 "ID33,Identifier Field 33"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x210)++0x03
|
|
line.long 0x00 "ID33,Identifier Field 33"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x210)++0x07
|
|
line.long 0x00 "DATA0-3_33,Data Field 0-3 33"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_33,Data Field 4-7 33"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x220)++0x03 "Message Buffer Register 34"
|
|
line.long 0x00 "C/S34,Control and Status 34"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x220)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x220)++0x03
|
|
line.long 0x00 "ID34,Identifier Field 34"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x220)++0x03
|
|
line.long 0x00 "ID34,Identifier Field 34"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x220)++0x07
|
|
line.long 0x00 "DATA0-3_34,Data Field 0-3 34"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_34,Data Field 4-7 34"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x230)++0x03 "Message Buffer Register 35"
|
|
line.long 0x00 "C/S35,Control and Status 35"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x230)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x230)++0x03
|
|
line.long 0x00 "ID35,Identifier Field 35"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x230)++0x03
|
|
line.long 0x00 "ID35,Identifier Field 35"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x230)++0x07
|
|
line.long 0x00 "DATA0-3_35,Data Field 0-3 35"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_35,Data Field 4-7 35"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x240)++0x03 "Message Buffer Register 36"
|
|
line.long 0x00 "C/S36,Control and Status 36"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x240)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x240)++0x03
|
|
line.long 0x00 "ID36,Identifier Field 36"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x240)++0x03
|
|
line.long 0x00 "ID36,Identifier Field 36"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x240)++0x07
|
|
line.long 0x00 "DATA0-3_36,Data Field 0-3 36"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_36,Data Field 4-7 36"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x250)++0x03 "Message Buffer Register 37"
|
|
line.long 0x00 "C/S37,Control and Status 37"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x250)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x250)++0x03
|
|
line.long 0x00 "ID37,Identifier Field 37"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x250)++0x03
|
|
line.long 0x00 "ID37,Identifier Field 37"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x250)++0x07
|
|
line.long 0x00 "DATA0-3_37,Data Field 0-3 37"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_37,Data Field 4-7 37"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x260)++0x03 "Message Buffer Register 38"
|
|
line.long 0x00 "C/S38,Control and Status 38"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x260)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x260)++0x03
|
|
line.long 0x00 "ID38,Identifier Field 38"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x260)++0x03
|
|
line.long 0x00 "ID38,Identifier Field 38"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x260)++0x07
|
|
line.long 0x00 "DATA0-3_38,Data Field 0-3 38"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_38,Data Field 4-7 38"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x270)++0x03 "Message Buffer Register 39"
|
|
line.long 0x00 "C/S39,Control and Status 39"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x270)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x270)++0x03
|
|
line.long 0x00 "ID39,Identifier Field 39"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x270)++0x03
|
|
line.long 0x00 "ID39,Identifier Field 39"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x270)++0x07
|
|
line.long 0x00 "DATA0-3_39,Data Field 0-3 39"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_39,Data Field 4-7 39"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x280)++0x03 "Message Buffer Register 40"
|
|
line.long 0x00 "C/S40,Control and Status 40"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x280)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x280)++0x03
|
|
line.long 0x00 "ID40,Identifier Field 40"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x280)++0x03
|
|
line.long 0x00 "ID40,Identifier Field 40"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x280)++0x07
|
|
line.long 0x00 "DATA0-3_40,Data Field 0-3 40"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_40,Data Field 4-7 40"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x290)++0x03 "Message Buffer Register 41"
|
|
line.long 0x00 "C/S41,Control and Status 41"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x290)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x290)++0x03
|
|
line.long 0x00 "ID41,Identifier Field 41"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x290)++0x03
|
|
line.long 0x00 "ID41,Identifier Field 41"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x290)++0x07
|
|
line.long 0x00 "DATA0-3_41,Data Field 0-3 41"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_41,Data Field 4-7 41"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2A0)++0x03 "Message Buffer Register 42"
|
|
line.long 0x00 "C/S42,Control and Status 42"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2A0)++0x03
|
|
line.long 0x00 "ID42,Identifier Field 42"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2A0)++0x03
|
|
line.long 0x00 "ID42,Identifier Field 42"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2A0)++0x07
|
|
line.long 0x00 "DATA0-3_42,Data Field 0-3 42"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_42,Data Field 4-7 42"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2B0)++0x03 "Message Buffer Register 43"
|
|
line.long 0x00 "C/S43,Control and Status 43"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2B0)++0x03
|
|
line.long 0x00 "ID43,Identifier Field 43"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2B0)++0x03
|
|
line.long 0x00 "ID43,Identifier Field 43"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2B0)++0x07
|
|
line.long 0x00 "DATA0-3_43,Data Field 0-3 43"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_43,Data Field 4-7 43"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2C0)++0x03 "Message Buffer Register 44"
|
|
line.long 0x00 "C/S44,Control and Status 44"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2C0)++0x03
|
|
line.long 0x00 "ID44,Identifier Field 44"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2C0)++0x03
|
|
line.long 0x00 "ID44,Identifier Field 44"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2C0)++0x07
|
|
line.long 0x00 "DATA0-3_44,Data Field 0-3 44"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_44,Data Field 4-7 44"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2D0)++0x03 "Message Buffer Register 45"
|
|
line.long 0x00 "C/S45,Control and Status 45"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2D0)++0x03
|
|
line.long 0x00 "ID45,Identifier Field 45"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2D0)++0x03
|
|
line.long 0x00 "ID45,Identifier Field 45"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2D0)++0x07
|
|
line.long 0x00 "DATA0-3_45,Data Field 0-3 45"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_45,Data Field 4-7 45"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2E0)++0x03 "Message Buffer Register 46"
|
|
line.long 0x00 "C/S46,Control and Status 46"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2E0)++0x03
|
|
line.long 0x00 "ID46,Identifier Field 46"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2E0)++0x03
|
|
line.long 0x00 "ID46,Identifier Field 46"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2E0)++0x07
|
|
line.long 0x00 "DATA0-3_46,Data Field 0-3 46"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_46,Data Field 4-7 46"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2F0)++0x03 "Message Buffer Register 47"
|
|
line.long 0x00 "C/S47,Control and Status 47"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x2F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2F0)++0x03
|
|
line.long 0x00 "ID47,Identifier Field 47"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2F0)++0x03
|
|
line.long 0x00 "ID47,Identifier Field 47"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2F0)++0x07
|
|
line.long 0x00 "DATA0-3_47,Data Field 0-3 47"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_47,Data Field 4-7 47"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 48-63"
|
|
group.long (0x0080+0x300)++0x03 "Message Buffer Register 48"
|
|
line.long 0x00 "C/S48,Control and Status 48"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x300)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x300)++0x03
|
|
line.long 0x00 "ID48,Identifier Field 48"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x300)++0x03
|
|
line.long 0x00 "ID48,Identifier Field 48"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x300)++0x07
|
|
line.long 0x00 "DATA0-3_48,Data Field 0-3 48"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_48,Data Field 4-7 48"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x310)++0x03 "Message Buffer Register 49"
|
|
line.long 0x00 "C/S49,Control and Status 49"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x310)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x310)++0x03
|
|
line.long 0x00 "ID49,Identifier Field 49"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x310)++0x03
|
|
line.long 0x00 "ID49,Identifier Field 49"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x310)++0x07
|
|
line.long 0x00 "DATA0-3_49,Data Field 0-3 49"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_49,Data Field 4-7 49"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x320)++0x03 "Message Buffer Register 50"
|
|
line.long 0x00 "C/S50,Control and Status 50"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x320)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x320)++0x03
|
|
line.long 0x00 "ID50,Identifier Field 50"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x320)++0x03
|
|
line.long 0x00 "ID50,Identifier Field 50"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x320)++0x07
|
|
line.long 0x00 "DATA0-3_50,Data Field 0-3 50"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_50,Data Field 4-7 50"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x330)++0x03 "Message Buffer Register 51"
|
|
line.long 0x00 "C/S51,Control and Status 51"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x330)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x330)++0x03
|
|
line.long 0x00 "ID51,Identifier Field 51"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x330)++0x03
|
|
line.long 0x00 "ID51,Identifier Field 51"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x330)++0x07
|
|
line.long 0x00 "DATA0-3_51,Data Field 0-3 51"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_51,Data Field 4-7 51"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x340)++0x03 "Message Buffer Register 52"
|
|
line.long 0x00 "C/S52,Control and Status 52"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x340)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x340)++0x03
|
|
line.long 0x00 "ID52,Identifier Field 52"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x340)++0x03
|
|
line.long 0x00 "ID52,Identifier Field 52"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x340)++0x07
|
|
line.long 0x00 "DATA0-3_52,Data Field 0-3 52"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_52,Data Field 4-7 52"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x350)++0x03 "Message Buffer Register 53"
|
|
line.long 0x00 "C/S53,Control and Status 53"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x350)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x350)++0x03
|
|
line.long 0x00 "ID53,Identifier Field 53"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x350)++0x03
|
|
line.long 0x00 "ID53,Identifier Field 53"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x350)++0x07
|
|
line.long 0x00 "DATA0-3_53,Data Field 0-3 53"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_53,Data Field 4-7 53"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x360)++0x03 "Message Buffer Register 54"
|
|
line.long 0x00 "C/S54,Control and Status 54"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x360)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x360)++0x03
|
|
line.long 0x00 "ID54,Identifier Field 54"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x360)++0x03
|
|
line.long 0x00 "ID54,Identifier Field 54"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x360)++0x07
|
|
line.long 0x00 "DATA0-3_54,Data Field 0-3 54"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_54,Data Field 4-7 54"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x370)++0x03 "Message Buffer Register 55"
|
|
line.long 0x00 "C/S55,Control and Status 55"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x370)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x370)++0x03
|
|
line.long 0x00 "ID55,Identifier Field 55"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x370)++0x03
|
|
line.long 0x00 "ID55,Identifier Field 55"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x370)++0x07
|
|
line.long 0x00 "DATA0-3_55,Data Field 0-3 55"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_55,Data Field 4-7 55"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x380)++0x03 "Message Buffer Register 56"
|
|
line.long 0x00 "C/S56,Control and Status 56"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x380)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x380)++0x03
|
|
line.long 0x00 "ID56,Identifier Field 56"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x380)++0x03
|
|
line.long 0x00 "ID56,Identifier Field 56"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x380)++0x07
|
|
line.long 0x00 "DATA0-3_56,Data Field 0-3 56"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_56,Data Field 4-7 56"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x390)++0x03 "Message Buffer Register 57"
|
|
line.long 0x00 "C/S57,Control and Status 57"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x390)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x390)++0x03
|
|
line.long 0x00 "ID57,Identifier Field 57"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x390)++0x03
|
|
line.long 0x00 "ID57,Identifier Field 57"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x390)++0x07
|
|
line.long 0x00 "DATA0-3_57,Data Field 0-3 57"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_57,Data Field 4-7 57"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3A0)++0x03 "Message Buffer Register 58"
|
|
line.long 0x00 "C/S58,Control and Status 58"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3A0)++0x03
|
|
line.long 0x00 "ID58,Identifier Field 58"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3A0)++0x03
|
|
line.long 0x00 "ID58,Identifier Field 58"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3A0)++0x07
|
|
line.long 0x00 "DATA0-3_58,Data Field 0-3 58"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_58,Data Field 4-7 58"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3B0)++0x03 "Message Buffer Register 59"
|
|
line.long 0x00 "C/S59,Control and Status 59"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3B0)++0x03
|
|
line.long 0x00 "ID59,Identifier Field 59"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3B0)++0x03
|
|
line.long 0x00 "ID59,Identifier Field 59"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3B0)++0x07
|
|
line.long 0x00 "DATA0-3_59,Data Field 0-3 59"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_59,Data Field 4-7 59"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3C0)++0x03 "Message Buffer Register 60"
|
|
line.long 0x00 "C/S60,Control and Status 60"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3C0)++0x03
|
|
line.long 0x00 "ID60,Identifier Field 60"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3C0)++0x03
|
|
line.long 0x00 "ID60,Identifier Field 60"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3C0)++0x07
|
|
line.long 0x00 "DATA0-3_60,Data Field 0-3 60"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_60,Data Field 4-7 60"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3D0)++0x03 "Message Buffer Register 61"
|
|
line.long 0x00 "C/S61,Control and Status 61"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3D0)++0x03
|
|
line.long 0x00 "ID61,Identifier Field 61"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3D0)++0x03
|
|
line.long 0x00 "ID61,Identifier Field 61"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3D0)++0x07
|
|
line.long 0x00 "DATA0-3_61,Data Field 0-3 61"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_61,Data Field 4-7 61"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3E0)++0x03 "Message Buffer Register 62"
|
|
line.long 0x00 "C/S62,Control and Status 62"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3E0)++0x03
|
|
line.long 0x00 "ID62,Identifier Field 62"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3E0)++0x03
|
|
line.long 0x00 "ID62,Identifier Field 62"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3E0)++0x07
|
|
line.long 0x00 "DATA0-3_62,Data Field 0-3 62"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_62,Data Field 4-7 62"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3F0)++0x03 "Message Buffer Register 63"
|
|
line.long 0x00 "C/S63,Control and Status 63"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE4000+0x0080+0x3F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3F0)++0x03
|
|
line.long 0x00 "ID63,Identifier Field 63"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3F0)++0x03
|
|
line.long 0x00 "ID63,Identifier Field 63"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3F0)++0x07
|
|
line.long 0x00 "DATA0-3_63,Data Field 0-3 63"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_63,Data Field 4-7 63"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
width 10.
|
|
tree "Common Registers"
|
|
group.long 0x0000++0x0b
|
|
line.long 0x00 "MCR,Module Configuration Register"
|
|
bitfld.long 0x00 31. " MDIS ,Module disable" "No,Yes"
|
|
bitfld.long 0x00 30. " FRZ ,Freeze enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " FEN ,FIFO feature enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " HALT ,FlexCAN freeze mode" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 27. " NOT_RDY ,FlexCAN not ready" "Normal/listen-only/loopback,Disable/doze/stop/freeze"
|
|
bitfld.long 0x00 26. " WAK_MSK ,Wake-up interrupt mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " SOFT_RST ,Soft reset" "No reset,Reset"
|
|
bitfld.long 0x00 24. " FRZ_ACK ,Freeze mode acknowledge" "Not acknowledged,Acknowledged"
|
|
textline " "
|
|
bitfld.long 0x00 23. " SUPV ,Supervisor mode" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " SLF_WAK ,Self wake-up" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " WRN_EN ,Warning Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " LPM_ACK ,Low power mode acknowledge" "No low-power,Disable/doze/stop"
|
|
textline " "
|
|
bitfld.long 0x00 19. " WAK_SRC ,Wake-up source" "Unfiltered Rx,Filtered Rx"
|
|
bitfld.long 0x00 18. " DOZE ,Doze mode enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRX_DIS ,Self Reception Disable" "No,Yes"
|
|
bitfld.long 0x00 16. " BCC ,Backwards Compatibility Configuration" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " LPRIO_EN ,Local priority feature enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " AEN ,Tx abort feature enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " IDAM ,Format of the elements of the Rx FIFO filter table" "A,B,C,D"
|
|
hexmask.long.byte 0x00 00.--05. 1. " MAXMB ,Maximum number of message buffers"
|
|
line.long 0x04 "CTRL,Control Register"
|
|
hexmask.long.byte 0x04 24.--31. 1. " PRESDIV ,Prescaler division factor"
|
|
bitfld.long 0x04 22.--23. " RJW ,Resync jump width" "1,2,3,4"
|
|
textline " "
|
|
bitfld.long 0x04 19.--21. " PSEG1 ,Phase Buffer Segment 1" "1,2,3,4,5,6,7,8"
|
|
bitfld.long 0x04 16.--18. " PSEG2 ,Phase Buffer Segment 2" "1,2,3,4,5,6,7,8"
|
|
textline " "
|
|
bitfld.long 0x04 15. " BOFF_MSK , Bus off mask" "Disabled,Enabled"
|
|
bitfld.long 0x04 14. " ERR_MSK , Error mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 13. " CLK_SRC ,CAN engine clock source" "Osc clk,Bus clk"
|
|
bitfld.long 0x04 12. " LPB ,Loop back" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 11. " TWRN_MSK ,Tx Warning interrupt mask" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " RWRN_MSK ,Rx Warning Interrupt Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 07. " SMP ,Sampling mode" "1 sample,3 samples"
|
|
bitfld.long 0x04 06. " BOFF_REC ,Bus off recovery mode" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x04 05. " TSYN ,Timer sync mode" "Disabled,Enabled"
|
|
bitfld.long 0x04 04. " LBUF ,Lowest buffer transmitted first" "With highest priority,Lowest number"
|
|
textline " "
|
|
bitfld.long 0x04 03. " LOM ,Listen-only mode" "Disabled,Enabled"
|
|
bitfld.long 0x04 00.--02. " PROPSEG ,Propagation segment" "1,2,3,4,5,6,7,8"
|
|
line.long 0x08 "TIMER,Free-Running Timer Register"
|
|
hexmask.long.word 0x08 00.--15. 1. " TIMER ,Timer value"
|
|
group.long 0x0010++0x0F
|
|
line.long 0x00 "RXGMASK,Rx Global Mask Register"
|
|
bitfld.long 0x00 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x00 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x00 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x00 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x00 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x00 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x00 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x00 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x00 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x00 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x00 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x00 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x00 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x00 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x00 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x00 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x00 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x00 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x00 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x00 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x00 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x00 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x00 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x00 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x00 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x00 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x00 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x00 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x00 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x04 "RX14MASK,Rx Buffer 14 Mask Register"
|
|
bitfld.long 0x04 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x04 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x04 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x04 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x04 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x04 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x04 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x04 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x04 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x04 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x04 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x04 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x04 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x04 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x04 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x04 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x04 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x04 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x04 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x04 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x04 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x04 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x04 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x04 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x04 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x04 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x04 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x04 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x04 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x08 "RX15MASK,Rx Buffer 15 Mask Register"
|
|
bitfld.long 0x08 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x08 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x08 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x08 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x08 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x08 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x08 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x08 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x08 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x08 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x08 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x08 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x08 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x08 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x08 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x08 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x08 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x08 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x08 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x08 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x08 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x08 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x08 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x08 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x08 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x08 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x08 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x08 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x08 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x0C "ECR,Error Counter Register"
|
|
hexmask.long.byte 0x0C 08.--15. 1. " RX_ERR_COUNTER ,Rx Error Counter"
|
|
hexmask.long.byte 0x0C 00.--07. 1. " TX_ERR_COUNTER ,Tx Error Counter"
|
|
hgroup.long 0x0020++0x03
|
|
hide.long 0x00 "ESR,Error and Status Register"
|
|
in
|
|
group.long 0x0028++0x03
|
|
line.long 0x00 "IMASK1,Interrupt Masks Register 1"
|
|
bitfld.long 0x00 31. " BUF31M ,Buffer 31 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " BUF30M ,Buffer 30 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " BUF29M ,Buffer 29 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " BUF28M ,Buffer 28 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 27. " BUF27M ,Buffer 27 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 26. " BUF26M ,Buffer 26 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " BUF25M ,Buffer 25 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 24. " BUF24M ,Buffer 24 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 23. " BUF23M ,Buffer 23 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " BUF22M ,Buffer 22 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " BUF21M ,Buffer 21 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " BUF20M ,Buffer 20 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " BUF19M ,Buffer 19 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " BUF18M ,Buffer 18 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " BUF17M ,Buffer 17 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " BUF16M ,Buffer 16 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " BUF15M ,Buffer 15 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " BUF14M ,Buffer 14 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " BUF13M ,Buffer 13 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " BUF12M ,Buffer 12 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BUF11M ,Buffer 11 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BUF10M ,Buffer 10 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 09. " BUF9M ,Buffer 9 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 08. " BUF8M ,Buffer 8 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 07. " BUF7M ,Buffer 7 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 06. " BUF6M ,Buffer 6 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 05. " BUF5M ,Buffer 5 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 04. " BUF4M ,Buffer 4 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 03. " BUF3M ,Buffer 3 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 02. " BUF2M ,Buffer 2 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 01. " BUF1M ,Buffer 1 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 00. " BUF0M ,Buffer 0 MB Mask" "Disabled,Enabled"
|
|
if (((data.long(asd:0x53FE4000))&0x20000000)==0x00)
|
|
group.long 0x0030++0x03
|
|
line.long 0x00 "IFLAG1,Interrupt Flags 1 Register"
|
|
eventfld.long 0x00 31. " BUF31I ,Buffer 31 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF30I ,Buffer 30 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF29I ,Buffer 29 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF28I ,Buffer 28 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF27I ,Buffer 27 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF26I ,Buffer 26 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF25I ,Buffer 25 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF24I ,Buffer 24 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF23I ,Buffer 23 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF22I ,Buffer 22 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF21I ,Buffer 21 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF20I ,Buffer 20 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF19I ,Buffer 19 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF18I ,Buffer 18 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF17I ,Buffer 17 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF16I ,Buffer 16 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF15I ,Buffer 15 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF14I ,Buffer 14 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF13I ,Buffer 13 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF12I ,Buffer 12 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF11I ,Buffer 11 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF10I ,Buffer 10 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 09. " BUF9I ,Buffer 9 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 08. " BUF8I ,Buffer 8 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 07. " BUF7I ,Buffer 7 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 06. " BUF6I ,Buffer 6 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 05. " BUF5I ,Buffer 5 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 04. " BUF4I ,Buffer 4 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 03. " BUF3I ,Buffer 3 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 02. " BUF2I ,Buffer 2 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 01. " BUF1I ,Buffer 1 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 00. " BUF0I ,Buffer 0 MB Interrupt" "Not occurred,Occurred"
|
|
else
|
|
group.long 0x0030++0x03
|
|
line.long 0x00 "IFLAG1,Interrupt Flags 1 Register"
|
|
eventfld.long 0x00 31. " BUF31I ,Buffer 31 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF30I ,Buffer 30 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF29I ,Buffer 29 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF28I ,Buffer 28 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF27I ,Buffer 27 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF26I ,Buffer 26 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF25I ,Buffer 25 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF24I ,Buffer 24 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF23I ,Buffer 23 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF22I ,Buffer 22 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF21I ,Buffer 21 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF20I ,Buffer 20 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF19I ,Buffer 19 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF18I ,Buffer 18 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF17I ,Buffer 17 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF16I ,Buffer 16 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF15I ,Buffer 15 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF14I ,Buffer 14 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF13I ,Buffer 13 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF12I ,Buffer 12 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF11I ,Buffer 11 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF10I ,Buffer 10 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 09. " BUF9I ,Buffer 9 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 08. " BUF8I ,Buffer 8 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 07. " BUF7I ,FIFO overflow condition" "No overflow,Overflow"
|
|
textline " "
|
|
eventfld.long 0x00 06. " BUF6I ,4 out of 6 buffers of the FIFO are already occupied" "Not occupied,Occupied"
|
|
textline " "
|
|
eventfld.long 0x00 05. " BUF5I ,Least one frame is available to be read from the FIFO" "Not available,Available"
|
|
endif
|
|
group.long 0x0024++0x03
|
|
line.long 0x00 "IMASK2,Interrupt Mask Register 2"
|
|
bitfld.long 0x00 31. " BUF63M ,Buffer 63 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " BUF62M ,Buffer 62 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " BUF61M ,Buffer 61 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " BUF60M ,Buffer 60 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 27. " BUF59M ,Buffer 59 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 26. " BUF58M ,Buffer 58 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " BUF57M ,Buffer 57 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 24. " BUF56M ,Buffer 56 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 23. " BUF55M ,Buffer 55 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " BUF54M ,Buffer 54 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " BUF53M ,Buffer 53 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " BUF52M ,Buffer 52 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " BUF51M ,Buffer 51 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " BUF50M ,Buffer 50 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " BUF49M ,Buffer 49 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " BUF48M ,Buffer 48 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " BUF47M ,Buffer 47 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " BUF46M ,Buffer 46 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " BUF45M ,Buffer 45 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " BUF44M ,Buffer 44 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BUF43M ,Buffer 43 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BUF42M ,Buffer 42 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " BUF41M ,Buffer 41 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " BUF40M ,Buffer 40 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BUF39M ,Buffer 39 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " BUF38M ,Buffer 38 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " BUF37M ,Buffer 37 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " BUF36M ,Buffer 36 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " BUF35M ,Buffer 35 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " BUF34M ,Buffer 34 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " BUF33M ,Buffer 33 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " BUF32M ,Buffer 32 MB Mask" "Disabled,Enabled"
|
|
group.long 0x002c++0x03
|
|
line.long 0x00 "IFLAG2,Interrupt Flags 2 Register"
|
|
eventfld.long 0x00 31. " BUF63I ,Buffer 63 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF62I ,Buffer 62 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF61I ,Buffer 61 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF60I ,Buffer 60 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF59I ,Buffer 59 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF58I ,Buffer 58 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF57I ,Buffer 57 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF56I ,Buffer 56 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF55I ,Buffer 55 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF54I ,Buffer 54 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF53I ,Buffer 53 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF52I ,Buffer 52 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF51I ,Buffer 51 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF50I ,Buffer 50 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF49I ,Buffer 49 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF48I ,Buffer 48 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF47I ,Buffer 47 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF46I ,Buffer 46 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF45I ,Buffer 45 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF44I ,Buffer 44 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF43I ,Buffer 43 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF42I ,Buffer 42 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 9. " BUF41I ,Buffer 41 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 8. " BUF40I ,Buffer 40 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 7. " BUF39I ,Buffer 39 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 6. " BUF38I ,Buffer 38 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 5. " BUF37I ,Buffer 37 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 4. " BUF36I ,Buffer 36 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 3. " BUF35I ,Buffer 35 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 2. " BUF34I ,Buffer 34 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 1. " BUF33I ,Buffer 33 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 0. " BUF32I ,Buffer 32 MB Interrupt" "Not occurred,Occurred"
|
|
tree.end
|
|
width 9.
|
|
tree "Rx Individual Mask Registers 0-15"
|
|
if (((data.long(d:0x53FE4000+0x80))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x0)++0x3
|
|
line.long 0x0 "RXIMR0,Rx Individual Mask Register 0"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x0)++0x3
|
|
line.long 0x0 "RXIMR0,Rx Individual Mask Register 0"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x90))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x4)++0x3
|
|
line.long 0x0 "RXIMR1,Rx Individual Mask Register 1"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x4)++0x3
|
|
line.long 0x0 "RXIMR1,Rx Individual Mask Register 1"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xA0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x8)++0x3
|
|
line.long 0x0 "RXIMR2,Rx Individual Mask Register 2"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x8)++0x3
|
|
line.long 0x0 "RXIMR2,Rx Individual Mask Register 2"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xB0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC)++0x3
|
|
line.long 0x0 "RXIMR3,Rx Individual Mask Register 3"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC)++0x3
|
|
line.long 0x0 "RXIMR3,Rx Individual Mask Register 3"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xC0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x10)++0x3
|
|
line.long 0x0 "RXIMR4,Rx Individual Mask Register 4"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x10)++0x3
|
|
line.long 0x0 "RXIMR4,Rx Individual Mask Register 4"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xD0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x14)++0x3
|
|
line.long 0x0 "RXIMR5,Rx Individual Mask Register 5"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x14)++0x3
|
|
line.long 0x0 "RXIMR5,Rx Individual Mask Register 5"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xE0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x18)++0x3
|
|
line.long 0x0 "RXIMR6,Rx Individual Mask Register 6"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x18)++0x3
|
|
line.long 0x0 "RXIMR6,Rx Individual Mask Register 6"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0xF0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x1C)++0x3
|
|
line.long 0x0 "RXIMR7,Rx Individual Mask Register 7"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x1C)++0x3
|
|
line.long 0x0 "RXIMR7,Rx Individual Mask Register 7"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x100))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x20)++0x3
|
|
line.long 0x0 "RXIMR8,Rx Individual Mask Register 8"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x20)++0x3
|
|
line.long 0x0 "RXIMR8,Rx Individual Mask Register 8"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x110))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x24)++0x3
|
|
line.long 0x0 "RXIMR9,Rx Individual Mask Register 9"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x24)++0x3
|
|
line.long 0x0 "RXIMR9,Rx Individual Mask Register 9"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x120))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x28)++0x3
|
|
line.long 0x0 "RXIMR10,Rx Individual Mask Register 10"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x28)++0x3
|
|
line.long 0x0 "RXIMR10,Rx Individual Mask Register 10"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x130))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x2C)++0x3
|
|
line.long 0x0 "RXIMR11,Rx Individual Mask Register 11"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x2C)++0x3
|
|
line.long 0x0 "RXIMR11,Rx Individual Mask Register 11"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x140))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x30)++0x3
|
|
line.long 0x0 "RXIMR12,Rx Individual Mask Register 12"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x30)++0x3
|
|
line.long 0x0 "RXIMR12,Rx Individual Mask Register 12"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x150))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x34)++0x3
|
|
line.long 0x0 "RXIMR13,Rx Individual Mask Register 13"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x34)++0x3
|
|
line.long 0x0 "RXIMR13,Rx Individual Mask Register 13"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x160))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x38)++0x3
|
|
line.long 0x0 "RXIMR14,Rx Individual Mask Register 14"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x38)++0x3
|
|
line.long 0x0 "RXIMR14,Rx Individual Mask Register 14"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x170))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x3C)++0x3
|
|
line.long 0x0 "RXIMR15,Rx Individual Mask Register 15"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x3C)++0x3
|
|
line.long 0x0 "RXIMR15,Rx Individual Mask Register 15"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 16-31"
|
|
if (((data.long(d:0x53FE4000+0x180))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x40)++0x3
|
|
line.long 0x0 "RXIMR16,Rx Individual Mask Register 16"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x40)++0x3
|
|
line.long 0x0 "RXIMR16,Rx Individual Mask Register 16"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x190))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x44)++0x3
|
|
line.long 0x0 "RXIMR17,Rx Individual Mask Register 17"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x44)++0x3
|
|
line.long 0x0 "RXIMR17,Rx Individual Mask Register 17"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x48)++0x3
|
|
line.long 0x0 "RXIMR18,Rx Individual Mask Register 18"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x48)++0x3
|
|
line.long 0x0 "RXIMR18,Rx Individual Mask Register 18"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x4C)++0x3
|
|
line.long 0x0 "RXIMR19,Rx Individual Mask Register 19"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x4C)++0x3
|
|
line.long 0x0 "RXIMR19,Rx Individual Mask Register 19"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x50)++0x3
|
|
line.long 0x0 "RXIMR20,Rx Individual Mask Register 20"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x50)++0x3
|
|
line.long 0x0 "RXIMR20,Rx Individual Mask Register 20"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x54)++0x3
|
|
line.long 0x0 "RXIMR21,Rx Individual Mask Register 21"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x54)++0x3
|
|
line.long 0x0 "RXIMR21,Rx Individual Mask Register 21"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x58)++0x3
|
|
line.long 0x0 "RXIMR22,Rx Individual Mask Register 22"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x58)++0x3
|
|
line.long 0x0 "RXIMR22,Rx Individual Mask Register 22"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x1F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x5C)++0x3
|
|
line.long 0x0 "RXIMR23,Rx Individual Mask Register 23"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x5C)++0x3
|
|
line.long 0x0 "RXIMR23,Rx Individual Mask Register 23"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x200))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x60)++0x3
|
|
line.long 0x0 "RXIMR24,Rx Individual Mask Register 24"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x60)++0x3
|
|
line.long 0x0 "RXIMR24,Rx Individual Mask Register 24"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x210))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x64)++0x3
|
|
line.long 0x0 "RXIMR25,Rx Individual Mask Register 25"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x64)++0x3
|
|
line.long 0x0 "RXIMR25,Rx Individual Mask Register 25"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x220))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x68)++0x3
|
|
line.long 0x0 "RXIMR26,Rx Individual Mask Register 26"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x68)++0x3
|
|
line.long 0x0 "RXIMR26,Rx Individual Mask Register 26"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x230))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x6C)++0x3
|
|
line.long 0x0 "RXIMR27,Rx Individual Mask Register 27"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x6C)++0x3
|
|
line.long 0x0 "RXIMR27,Rx Individual Mask Register 27"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x240))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x70)++0x3
|
|
line.long 0x0 "RXIMR28,Rx Individual Mask Register 28"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x70)++0x3
|
|
line.long 0x0 "RXIMR28,Rx Individual Mask Register 28"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x250))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x74)++0x3
|
|
line.long 0x0 "RXIMR29,Rx Individual Mask Register 29"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x74)++0x3
|
|
line.long 0x0 "RXIMR29,Rx Individual Mask Register 29"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x260))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x78)++0x3
|
|
line.long 0x0 "RXIMR30,Rx Individual Mask Register 30"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x78)++0x3
|
|
line.long 0x0 "RXIMR30,Rx Individual Mask Register 30"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x270))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x7C)++0x3
|
|
line.long 0x0 "RXIMR31,Rx Individual Mask Register 31"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x7C)++0x3
|
|
line.long 0x0 "RXIMR31,Rx Individual Mask Register 31"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 32-47"
|
|
if (((data.long(d:0x53FE4000+0x280))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x80)++0x3
|
|
line.long 0x0 "RXIMR32,Rx Individual Mask Register 32"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x80)++0x3
|
|
line.long 0x0 "RXIMR32,Rx Individual Mask Register 32"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x290))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x84)++0x3
|
|
line.long 0x0 "RXIMR33,Rx Individual Mask Register 33"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x84)++0x3
|
|
line.long 0x0 "RXIMR33,Rx Individual Mask Register 33"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x88)++0x3
|
|
line.long 0x0 "RXIMR34,Rx Individual Mask Register 34"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x88)++0x3
|
|
line.long 0x0 "RXIMR34,Rx Individual Mask Register 34"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x8C)++0x3
|
|
line.long 0x0 "RXIMR35,Rx Individual Mask Register 35"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x8C)++0x3
|
|
line.long 0x0 "RXIMR35,Rx Individual Mask Register 35"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x90)++0x3
|
|
line.long 0x0 "RXIMR36,Rx Individual Mask Register 36"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x90)++0x3
|
|
line.long 0x0 "RXIMR36,Rx Individual Mask Register 36"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x94)++0x3
|
|
line.long 0x0 "RXIMR37,Rx Individual Mask Register 37"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x94)++0x3
|
|
line.long 0x0 "RXIMR37,Rx Individual Mask Register 37"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x98)++0x3
|
|
line.long 0x0 "RXIMR38,Rx Individual Mask Register 38"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x98)++0x3
|
|
line.long 0x0 "RXIMR38,Rx Individual Mask Register 38"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x2F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x9C)++0x3
|
|
line.long 0x0 "RXIMR39,Rx Individual Mask Register 39"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x9C)++0x3
|
|
line.long 0x0 "RXIMR39,Rx Individual Mask Register 39"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x300))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA0)++0x3
|
|
line.long 0x0 "RXIMR40,Rx Individual Mask Register 40"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA0)++0x3
|
|
line.long 0x0 "RXIMR40,Rx Individual Mask Register 40"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x310))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA4)++0x3
|
|
line.long 0x0 "RXIMR41,Rx Individual Mask Register 41"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA4)++0x3
|
|
line.long 0x0 "RXIMR41,Rx Individual Mask Register 41"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x320))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA8)++0x3
|
|
line.long 0x0 "RXIMR42,Rx Individual Mask Register 42"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA8)++0x3
|
|
line.long 0x0 "RXIMR42,Rx Individual Mask Register 42"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x330))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xAC)++0x3
|
|
line.long 0x0 "RXIMR43,Rx Individual Mask Register 43"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xAC)++0x3
|
|
line.long 0x0 "RXIMR43,Rx Individual Mask Register 43"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x340))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB0)++0x3
|
|
line.long 0x0 "RXIMR44,Rx Individual Mask Register 44"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB0)++0x3
|
|
line.long 0x0 "RXIMR44,Rx Individual Mask Register 44"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x350))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB4)++0x3
|
|
line.long 0x0 "RXIMR45,Rx Individual Mask Register 45"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB4)++0x3
|
|
line.long 0x0 "RXIMR45,Rx Individual Mask Register 45"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x360))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB8)++0x3
|
|
line.long 0x0 "RXIMR46,Rx Individual Mask Register 46"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB8)++0x3
|
|
line.long 0x0 "RXIMR46,Rx Individual Mask Register 46"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x370))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xBC)++0x3
|
|
line.long 0x0 "RXIMR47,Rx Individual Mask Register 47"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xBC)++0x3
|
|
line.long 0x0 "RXIMR47,Rx Individual Mask Register 47"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 48-63"
|
|
if (((data.long(d:0x53FE4000+0x380))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC0)++0x3
|
|
line.long 0x0 "RXIMR48,Rx Individual Mask Register 48"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC0)++0x3
|
|
line.long 0x0 "RXIMR48,Rx Individual Mask Register 48"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x390))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC4)++0x3
|
|
line.long 0x0 "RXIMR49,Rx Individual Mask Register 49"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC4)++0x3
|
|
line.long 0x0 "RXIMR49,Rx Individual Mask Register 49"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC8)++0x3
|
|
line.long 0x0 "RXIMR50,Rx Individual Mask Register 50"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC8)++0x3
|
|
line.long 0x0 "RXIMR50,Rx Individual Mask Register 50"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xCC)++0x3
|
|
line.long 0x0 "RXIMR51,Rx Individual Mask Register 51"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xCC)++0x3
|
|
line.long 0x0 "RXIMR51,Rx Individual Mask Register 51"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD0)++0x3
|
|
line.long 0x0 "RXIMR52,Rx Individual Mask Register 52"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD0)++0x3
|
|
line.long 0x0 "RXIMR52,Rx Individual Mask Register 52"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD4)++0x3
|
|
line.long 0x0 "RXIMR53,Rx Individual Mask Register 53"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD4)++0x3
|
|
line.long 0x0 "RXIMR53,Rx Individual Mask Register 53"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD8)++0x3
|
|
line.long 0x0 "RXIMR54,Rx Individual Mask Register 54"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD8)++0x3
|
|
line.long 0x0 "RXIMR54,Rx Individual Mask Register 54"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x3F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xDC)++0x3
|
|
line.long 0x0 "RXIMR55,Rx Individual Mask Register 55"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xDC)++0x3
|
|
line.long 0x0 "RXIMR55,Rx Individual Mask Register 55"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x400))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE0)++0x3
|
|
line.long 0x0 "RXIMR56,Rx Individual Mask Register 56"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE0)++0x3
|
|
line.long 0x0 "RXIMR56,Rx Individual Mask Register 56"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x410))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE4)++0x3
|
|
line.long 0x0 "RXIMR57,Rx Individual Mask Register 57"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE4)++0x3
|
|
line.long 0x0 "RXIMR57,Rx Individual Mask Register 57"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x420))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE8)++0x3
|
|
line.long 0x0 "RXIMR58,Rx Individual Mask Register 58"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE8)++0x3
|
|
line.long 0x0 "RXIMR58,Rx Individual Mask Register 58"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x430))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xEC)++0x3
|
|
line.long 0x0 "RXIMR59,Rx Individual Mask Register 59"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xEC)++0x3
|
|
line.long 0x0 "RXIMR59,Rx Individual Mask Register 59"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x440))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF0)++0x3
|
|
line.long 0x0 "RXIMR60,Rx Individual Mask Register 60"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF0)++0x3
|
|
line.long 0x0 "RXIMR60,Rx Individual Mask Register 60"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x450))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF4)++0x3
|
|
line.long 0x0 "RXIMR61,Rx Individual Mask Register 61"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF4)++0x3
|
|
line.long 0x0 "RXIMR61,Rx Individual Mask Register 61"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x460))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF8)++0x3
|
|
line.long 0x0 "RXIMR62,Rx Individual Mask Register 62"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF8)++0x3
|
|
line.long 0x0 "RXIMR62,Rx Individual Mask Register 62"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE4000+0x470))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xFC)++0x3
|
|
line.long 0x0 "RXIMR63,Rx Individual Mask Register 63"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xFC)++0x3
|
|
line.long 0x0 "RXIMR63,Rx Individual Mask Register 63"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
width 0xB
|
|
tree.end
|
|
tree "CAN 2"
|
|
base ad:0x53FE8000
|
|
width 12.
|
|
tree "Message Buffer Registers 0-15"
|
|
group.long (0x0080+0x0)++0x03 "Message Buffer Register 0"
|
|
line.long 0x00 "C/S0,Control and Status 0"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x0)++0x03
|
|
line.long 0x00 "ID0,Identifier Field 0"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x0)++0x03
|
|
line.long 0x00 "ID0,Identifier Field 0"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x0)++0x07
|
|
line.long 0x00 "DATA0-3_0,Data Field 0-3 0"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_0,Data Field 4-7 0"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x10)++0x03 "Message Buffer Register 1"
|
|
line.long 0x00 "C/S1,Control and Status 1"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x10)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x10)++0x03
|
|
line.long 0x00 "ID1,Identifier Field 1"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x10)++0x03
|
|
line.long 0x00 "ID1,Identifier Field 1"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x10)++0x07
|
|
line.long 0x00 "DATA0-3_1,Data Field 0-3 1"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_1,Data Field 4-7 1"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x20)++0x03 "Message Buffer Register 2"
|
|
line.long 0x00 "C/S2,Control and Status 2"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x20)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x20)++0x03
|
|
line.long 0x00 "ID2,Identifier Field 2"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x20)++0x03
|
|
line.long 0x00 "ID2,Identifier Field 2"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x20)++0x07
|
|
line.long 0x00 "DATA0-3_2,Data Field 0-3 2"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_2,Data Field 4-7 2"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x30)++0x03 "Message Buffer Register 3"
|
|
line.long 0x00 "C/S3,Control and Status 3"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x30)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x30)++0x03
|
|
line.long 0x00 "ID3,Identifier Field 3"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x30)++0x03
|
|
line.long 0x00 "ID3,Identifier Field 3"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x30)++0x07
|
|
line.long 0x00 "DATA0-3_3,Data Field 0-3 3"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_3,Data Field 4-7 3"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x40)++0x03 "Message Buffer Register 4"
|
|
line.long 0x00 "C/S4,Control and Status 4"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x40)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x40)++0x03
|
|
line.long 0x00 "ID4,Identifier Field 4"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x40)++0x03
|
|
line.long 0x00 "ID4,Identifier Field 4"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x40)++0x07
|
|
line.long 0x00 "DATA0-3_4,Data Field 0-3 4"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_4,Data Field 4-7 4"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x50)++0x03 "Message Buffer Register 5"
|
|
line.long 0x00 "C/S5,Control and Status 5"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x50)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x50)++0x03
|
|
line.long 0x00 "ID5,Identifier Field 5"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x50)++0x03
|
|
line.long 0x00 "ID5,Identifier Field 5"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x50)++0x07
|
|
line.long 0x00 "DATA0-3_5,Data Field 0-3 5"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_5,Data Field 4-7 5"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x60)++0x03 "Message Buffer Register 6"
|
|
line.long 0x00 "C/S6,Control and Status 6"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x60)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x60)++0x03
|
|
line.long 0x00 "ID6,Identifier Field 6"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x60)++0x03
|
|
line.long 0x00 "ID6,Identifier Field 6"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x60)++0x07
|
|
line.long 0x00 "DATA0-3_6,Data Field 0-3 6"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_6,Data Field 4-7 6"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x70)++0x03 "Message Buffer Register 7"
|
|
line.long 0x00 "C/S7,Control and Status 7"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x70)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x70)++0x03
|
|
line.long 0x00 "ID7,Identifier Field 7"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x70)++0x03
|
|
line.long 0x00 "ID7,Identifier Field 7"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x70)++0x07
|
|
line.long 0x00 "DATA0-3_7,Data Field 0-3 7"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_7,Data Field 4-7 7"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x80)++0x03 "Message Buffer Register 8"
|
|
line.long 0x00 "C/S8,Control and Status 8"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x80)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x80)++0x03
|
|
line.long 0x00 "ID8,Identifier Field 8"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x80)++0x03
|
|
line.long 0x00 "ID8,Identifier Field 8"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x80)++0x07
|
|
line.long 0x00 "DATA0-3_8,Data Field 0-3 8"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_8,Data Field 4-7 8"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x90)++0x03 "Message Buffer Register 9"
|
|
line.long 0x00 "C/S9,Control and Status 9"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x90)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x90)++0x03
|
|
line.long 0x00 "ID9,Identifier Field 9"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x90)++0x03
|
|
line.long 0x00 "ID9,Identifier Field 9"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x90)++0x07
|
|
line.long 0x00 "DATA0-3_9,Data Field 0-3 9"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_9,Data Field 4-7 9"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xA0)++0x03 "Message Buffer Register 10"
|
|
line.long 0x00 "C/S10,Control and Status 10"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xA0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xA0)++0x03
|
|
line.long 0x00 "ID10,Identifier Field 10"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xA0)++0x03
|
|
line.long 0x00 "ID10,Identifier Field 10"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xA0)++0x07
|
|
line.long 0x00 "DATA0-3_10,Data Field 0-3 10"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_10,Data Field 4-7 10"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xB0)++0x03 "Message Buffer Register 11"
|
|
line.long 0x00 "C/S11,Control and Status 11"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xB0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xB0)++0x03
|
|
line.long 0x00 "ID11,Identifier Field 11"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xB0)++0x03
|
|
line.long 0x00 "ID11,Identifier Field 11"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xB0)++0x07
|
|
line.long 0x00 "DATA0-3_11,Data Field 0-3 11"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_11,Data Field 4-7 11"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xC0)++0x03 "Message Buffer Register 12"
|
|
line.long 0x00 "C/S12,Control and Status 12"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xC0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xC0)++0x03
|
|
line.long 0x00 "ID12,Identifier Field 12"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xC0)++0x03
|
|
line.long 0x00 "ID12,Identifier Field 12"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xC0)++0x07
|
|
line.long 0x00 "DATA0-3_12,Data Field 0-3 12"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_12,Data Field 4-7 12"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xD0)++0x03 "Message Buffer Register 13"
|
|
line.long 0x00 "C/S13,Control and Status 13"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xD0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xD0)++0x03
|
|
line.long 0x00 "ID13,Identifier Field 13"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xD0)++0x03
|
|
line.long 0x00 "ID13,Identifier Field 13"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xD0)++0x07
|
|
line.long 0x00 "DATA0-3_13,Data Field 0-3 13"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_13,Data Field 4-7 13"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xE0)++0x03 "Message Buffer Register 14"
|
|
line.long 0x00 "C/S14,Control and Status 14"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xE0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xE0)++0x03
|
|
line.long 0x00 "ID14,Identifier Field 14"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xE0)++0x03
|
|
line.long 0x00 "ID14,Identifier Field 14"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xE0)++0x07
|
|
line.long 0x00 "DATA0-3_14,Data Field 0-3 14"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_14,Data Field 4-7 14"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0xF0)++0x03 "Message Buffer Register 15"
|
|
line.long 0x00 "C/S15,Control and Status 15"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0xF0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0xF0)++0x03
|
|
line.long 0x00 "ID15,Identifier Field 15"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0xF0)++0x03
|
|
line.long 0x00 "ID15,Identifier Field 15"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0xF0)++0x07
|
|
line.long 0x00 "DATA0-3_15,Data Field 0-3 15"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_15,Data Field 4-7 15"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 16-31"
|
|
group.long (0x0080+0x100)++0x03 "Message Buffer Register 16"
|
|
line.long 0x00 "C/S16,Control and Status 16"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x100)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x100)++0x03
|
|
line.long 0x00 "ID16,Identifier Field 16"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x100)++0x03
|
|
line.long 0x00 "ID16,Identifier Field 16"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x100)++0x07
|
|
line.long 0x00 "DATA0-3_16,Data Field 0-3 16"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_16,Data Field 4-7 16"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x110)++0x03 "Message Buffer Register 17"
|
|
line.long 0x00 "C/S17,Control and Status 17"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x110)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x110)++0x03
|
|
line.long 0x00 "ID17,Identifier Field 17"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x110)++0x03
|
|
line.long 0x00 "ID17,Identifier Field 17"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x110)++0x07
|
|
line.long 0x00 "DATA0-3_17,Data Field 0-3 17"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_17,Data Field 4-7 17"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x120)++0x03 "Message Buffer Register 18"
|
|
line.long 0x00 "C/S18,Control and Status 18"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x120)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x120)++0x03
|
|
line.long 0x00 "ID18,Identifier Field 18"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x120)++0x03
|
|
line.long 0x00 "ID18,Identifier Field 18"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x120)++0x07
|
|
line.long 0x00 "DATA0-3_18,Data Field 0-3 18"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_18,Data Field 4-7 18"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x130)++0x03 "Message Buffer Register 19"
|
|
line.long 0x00 "C/S19,Control and Status 19"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x130)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x130)++0x03
|
|
line.long 0x00 "ID19,Identifier Field 19"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x130)++0x03
|
|
line.long 0x00 "ID19,Identifier Field 19"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x130)++0x07
|
|
line.long 0x00 "DATA0-3_19,Data Field 0-3 19"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_19,Data Field 4-7 19"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x140)++0x03 "Message Buffer Register 20"
|
|
line.long 0x00 "C/S20,Control and Status 20"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x140)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x140)++0x03
|
|
line.long 0x00 "ID20,Identifier Field 20"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x140)++0x03
|
|
line.long 0x00 "ID20,Identifier Field 20"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x140)++0x07
|
|
line.long 0x00 "DATA0-3_20,Data Field 0-3 20"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_20,Data Field 4-7 20"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x150)++0x03 "Message Buffer Register 21"
|
|
line.long 0x00 "C/S21,Control and Status 21"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x150)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x150)++0x03
|
|
line.long 0x00 "ID21,Identifier Field 21"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x150)++0x03
|
|
line.long 0x00 "ID21,Identifier Field 21"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x150)++0x07
|
|
line.long 0x00 "DATA0-3_21,Data Field 0-3 21"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_21,Data Field 4-7 21"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x160)++0x03 "Message Buffer Register 22"
|
|
line.long 0x00 "C/S22,Control and Status 22"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x160)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x160)++0x03
|
|
line.long 0x00 "ID22,Identifier Field 22"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x160)++0x03
|
|
line.long 0x00 "ID22,Identifier Field 22"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x160)++0x07
|
|
line.long 0x00 "DATA0-3_22,Data Field 0-3 22"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_22,Data Field 4-7 22"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x170)++0x03 "Message Buffer Register 23"
|
|
line.long 0x00 "C/S23,Control and Status 23"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x170)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x170)++0x03
|
|
line.long 0x00 "ID23,Identifier Field 23"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x170)++0x03
|
|
line.long 0x00 "ID23,Identifier Field 23"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x170)++0x07
|
|
line.long 0x00 "DATA0-3_23,Data Field 0-3 23"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_23,Data Field 4-7 23"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x180)++0x03 "Message Buffer Register 24"
|
|
line.long 0x00 "C/S24,Control and Status 24"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x180)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x180)++0x03
|
|
line.long 0x00 "ID24,Identifier Field 24"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x180)++0x03
|
|
line.long 0x00 "ID24,Identifier Field 24"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x180)++0x07
|
|
line.long 0x00 "DATA0-3_24,Data Field 0-3 24"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_24,Data Field 4-7 24"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x190)++0x03 "Message Buffer Register 25"
|
|
line.long 0x00 "C/S25,Control and Status 25"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x190)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x190)++0x03
|
|
line.long 0x00 "ID25,Identifier Field 25"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x190)++0x03
|
|
line.long 0x00 "ID25,Identifier Field 25"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x190)++0x07
|
|
line.long 0x00 "DATA0-3_25,Data Field 0-3 25"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_25,Data Field 4-7 25"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1A0)++0x03 "Message Buffer Register 26"
|
|
line.long 0x00 "C/S26,Control and Status 26"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1A0)++0x03
|
|
line.long 0x00 "ID26,Identifier Field 26"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1A0)++0x03
|
|
line.long 0x00 "ID26,Identifier Field 26"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1A0)++0x07
|
|
line.long 0x00 "DATA0-3_26,Data Field 0-3 26"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_26,Data Field 4-7 26"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1B0)++0x03 "Message Buffer Register 27"
|
|
line.long 0x00 "C/S27,Control and Status 27"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1B0)++0x03
|
|
line.long 0x00 "ID27,Identifier Field 27"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1B0)++0x03
|
|
line.long 0x00 "ID27,Identifier Field 27"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1B0)++0x07
|
|
line.long 0x00 "DATA0-3_27,Data Field 0-3 27"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_27,Data Field 4-7 27"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1C0)++0x03 "Message Buffer Register 28"
|
|
line.long 0x00 "C/S28,Control and Status 28"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1C0)++0x03
|
|
line.long 0x00 "ID28,Identifier Field 28"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1C0)++0x03
|
|
line.long 0x00 "ID28,Identifier Field 28"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1C0)++0x07
|
|
line.long 0x00 "DATA0-3_28,Data Field 0-3 28"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_28,Data Field 4-7 28"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1D0)++0x03 "Message Buffer Register 29"
|
|
line.long 0x00 "C/S29,Control and Status 29"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1D0)++0x03
|
|
line.long 0x00 "ID29,Identifier Field 29"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1D0)++0x03
|
|
line.long 0x00 "ID29,Identifier Field 29"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1D0)++0x07
|
|
line.long 0x00 "DATA0-3_29,Data Field 0-3 29"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_29,Data Field 4-7 29"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1E0)++0x03 "Message Buffer Register 30"
|
|
line.long 0x00 "C/S30,Control and Status 30"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1E0)++0x03
|
|
line.long 0x00 "ID30,Identifier Field 30"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1E0)++0x03
|
|
line.long 0x00 "ID30,Identifier Field 30"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1E0)++0x07
|
|
line.long 0x00 "DATA0-3_30,Data Field 0-3 30"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_30,Data Field 4-7 30"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x1F0)++0x03 "Message Buffer Register 31"
|
|
line.long 0x00 "C/S31,Control and Status 31"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x1F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x1F0)++0x03
|
|
line.long 0x00 "ID31,Identifier Field 31"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x1F0)++0x03
|
|
line.long 0x00 "ID31,Identifier Field 31"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x1F0)++0x07
|
|
line.long 0x00 "DATA0-3_31,Data Field 0-3 31"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_31,Data Field 4-7 31"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 32-47"
|
|
group.long (0x0080+0x200)++0x03 "Message Buffer Register 32"
|
|
line.long 0x00 "C/S32,Control and Status 32"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x200)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x200)++0x03
|
|
line.long 0x00 "ID32,Identifier Field 32"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x200)++0x03
|
|
line.long 0x00 "ID32,Identifier Field 32"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x200)++0x07
|
|
line.long 0x00 "DATA0-3_32,Data Field 0-3 32"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_32,Data Field 4-7 32"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x210)++0x03 "Message Buffer Register 33"
|
|
line.long 0x00 "C/S33,Control and Status 33"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x210)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x210)++0x03
|
|
line.long 0x00 "ID33,Identifier Field 33"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x210)++0x03
|
|
line.long 0x00 "ID33,Identifier Field 33"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x210)++0x07
|
|
line.long 0x00 "DATA0-3_33,Data Field 0-3 33"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_33,Data Field 4-7 33"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x220)++0x03 "Message Buffer Register 34"
|
|
line.long 0x00 "C/S34,Control and Status 34"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x220)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x220)++0x03
|
|
line.long 0x00 "ID34,Identifier Field 34"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x220)++0x03
|
|
line.long 0x00 "ID34,Identifier Field 34"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x220)++0x07
|
|
line.long 0x00 "DATA0-3_34,Data Field 0-3 34"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_34,Data Field 4-7 34"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x230)++0x03 "Message Buffer Register 35"
|
|
line.long 0x00 "C/S35,Control and Status 35"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x230)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x230)++0x03
|
|
line.long 0x00 "ID35,Identifier Field 35"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x230)++0x03
|
|
line.long 0x00 "ID35,Identifier Field 35"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x230)++0x07
|
|
line.long 0x00 "DATA0-3_35,Data Field 0-3 35"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_35,Data Field 4-7 35"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x240)++0x03 "Message Buffer Register 36"
|
|
line.long 0x00 "C/S36,Control and Status 36"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x240)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x240)++0x03
|
|
line.long 0x00 "ID36,Identifier Field 36"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x240)++0x03
|
|
line.long 0x00 "ID36,Identifier Field 36"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x240)++0x07
|
|
line.long 0x00 "DATA0-3_36,Data Field 0-3 36"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_36,Data Field 4-7 36"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x250)++0x03 "Message Buffer Register 37"
|
|
line.long 0x00 "C/S37,Control and Status 37"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x250)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x250)++0x03
|
|
line.long 0x00 "ID37,Identifier Field 37"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x250)++0x03
|
|
line.long 0x00 "ID37,Identifier Field 37"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x250)++0x07
|
|
line.long 0x00 "DATA0-3_37,Data Field 0-3 37"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_37,Data Field 4-7 37"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x260)++0x03 "Message Buffer Register 38"
|
|
line.long 0x00 "C/S38,Control and Status 38"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x260)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x260)++0x03
|
|
line.long 0x00 "ID38,Identifier Field 38"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x260)++0x03
|
|
line.long 0x00 "ID38,Identifier Field 38"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x260)++0x07
|
|
line.long 0x00 "DATA0-3_38,Data Field 0-3 38"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_38,Data Field 4-7 38"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x270)++0x03 "Message Buffer Register 39"
|
|
line.long 0x00 "C/S39,Control and Status 39"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x270)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x270)++0x03
|
|
line.long 0x00 "ID39,Identifier Field 39"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x270)++0x03
|
|
line.long 0x00 "ID39,Identifier Field 39"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x270)++0x07
|
|
line.long 0x00 "DATA0-3_39,Data Field 0-3 39"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_39,Data Field 4-7 39"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x280)++0x03 "Message Buffer Register 40"
|
|
line.long 0x00 "C/S40,Control and Status 40"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x280)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x280)++0x03
|
|
line.long 0x00 "ID40,Identifier Field 40"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x280)++0x03
|
|
line.long 0x00 "ID40,Identifier Field 40"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x280)++0x07
|
|
line.long 0x00 "DATA0-3_40,Data Field 0-3 40"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_40,Data Field 4-7 40"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x290)++0x03 "Message Buffer Register 41"
|
|
line.long 0x00 "C/S41,Control and Status 41"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x290)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x290)++0x03
|
|
line.long 0x00 "ID41,Identifier Field 41"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x290)++0x03
|
|
line.long 0x00 "ID41,Identifier Field 41"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x290)++0x07
|
|
line.long 0x00 "DATA0-3_41,Data Field 0-3 41"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_41,Data Field 4-7 41"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2A0)++0x03 "Message Buffer Register 42"
|
|
line.long 0x00 "C/S42,Control and Status 42"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2A0)++0x03
|
|
line.long 0x00 "ID42,Identifier Field 42"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2A0)++0x03
|
|
line.long 0x00 "ID42,Identifier Field 42"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2A0)++0x07
|
|
line.long 0x00 "DATA0-3_42,Data Field 0-3 42"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_42,Data Field 4-7 42"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2B0)++0x03 "Message Buffer Register 43"
|
|
line.long 0x00 "C/S43,Control and Status 43"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2B0)++0x03
|
|
line.long 0x00 "ID43,Identifier Field 43"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2B0)++0x03
|
|
line.long 0x00 "ID43,Identifier Field 43"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2B0)++0x07
|
|
line.long 0x00 "DATA0-3_43,Data Field 0-3 43"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_43,Data Field 4-7 43"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2C0)++0x03 "Message Buffer Register 44"
|
|
line.long 0x00 "C/S44,Control and Status 44"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2C0)++0x03
|
|
line.long 0x00 "ID44,Identifier Field 44"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2C0)++0x03
|
|
line.long 0x00 "ID44,Identifier Field 44"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2C0)++0x07
|
|
line.long 0x00 "DATA0-3_44,Data Field 0-3 44"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_44,Data Field 4-7 44"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2D0)++0x03 "Message Buffer Register 45"
|
|
line.long 0x00 "C/S45,Control and Status 45"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2D0)++0x03
|
|
line.long 0x00 "ID45,Identifier Field 45"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2D0)++0x03
|
|
line.long 0x00 "ID45,Identifier Field 45"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2D0)++0x07
|
|
line.long 0x00 "DATA0-3_45,Data Field 0-3 45"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_45,Data Field 4-7 45"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2E0)++0x03 "Message Buffer Register 46"
|
|
line.long 0x00 "C/S46,Control and Status 46"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2E0)++0x03
|
|
line.long 0x00 "ID46,Identifier Field 46"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2E0)++0x03
|
|
line.long 0x00 "ID46,Identifier Field 46"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2E0)++0x07
|
|
line.long 0x00 "DATA0-3_46,Data Field 0-3 46"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_46,Data Field 4-7 46"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x2F0)++0x03 "Message Buffer Register 47"
|
|
line.long 0x00 "C/S47,Control and Status 47"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x2F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x2F0)++0x03
|
|
line.long 0x00 "ID47,Identifier Field 47"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x2F0)++0x03
|
|
line.long 0x00 "ID47,Identifier Field 47"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x2F0)++0x07
|
|
line.long 0x00 "DATA0-3_47,Data Field 0-3 47"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_47,Data Field 4-7 47"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
tree "Message Buffer Registers 48-63"
|
|
group.long (0x0080+0x300)++0x03 "Message Buffer Register 48"
|
|
line.long 0x00 "C/S48,Control and Status 48"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x300)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x300)++0x03
|
|
line.long 0x00 "ID48,Identifier Field 48"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x300)++0x03
|
|
line.long 0x00 "ID48,Identifier Field 48"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x300)++0x07
|
|
line.long 0x00 "DATA0-3_48,Data Field 0-3 48"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_48,Data Field 4-7 48"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x310)++0x03 "Message Buffer Register 49"
|
|
line.long 0x00 "C/S49,Control and Status 49"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x310)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x310)++0x03
|
|
line.long 0x00 "ID49,Identifier Field 49"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x310)++0x03
|
|
line.long 0x00 "ID49,Identifier Field 49"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x310)++0x07
|
|
line.long 0x00 "DATA0-3_49,Data Field 0-3 49"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_49,Data Field 4-7 49"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x320)++0x03 "Message Buffer Register 50"
|
|
line.long 0x00 "C/S50,Control and Status 50"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x320)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x320)++0x03
|
|
line.long 0x00 "ID50,Identifier Field 50"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x320)++0x03
|
|
line.long 0x00 "ID50,Identifier Field 50"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x320)++0x07
|
|
line.long 0x00 "DATA0-3_50,Data Field 0-3 50"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_50,Data Field 4-7 50"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x330)++0x03 "Message Buffer Register 51"
|
|
line.long 0x00 "C/S51,Control and Status 51"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x330)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x330)++0x03
|
|
line.long 0x00 "ID51,Identifier Field 51"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x330)++0x03
|
|
line.long 0x00 "ID51,Identifier Field 51"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x330)++0x07
|
|
line.long 0x00 "DATA0-3_51,Data Field 0-3 51"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_51,Data Field 4-7 51"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x340)++0x03 "Message Buffer Register 52"
|
|
line.long 0x00 "C/S52,Control and Status 52"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x340)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x340)++0x03
|
|
line.long 0x00 "ID52,Identifier Field 52"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x340)++0x03
|
|
line.long 0x00 "ID52,Identifier Field 52"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x340)++0x07
|
|
line.long 0x00 "DATA0-3_52,Data Field 0-3 52"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_52,Data Field 4-7 52"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x350)++0x03 "Message Buffer Register 53"
|
|
line.long 0x00 "C/S53,Control and Status 53"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x350)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x350)++0x03
|
|
line.long 0x00 "ID53,Identifier Field 53"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x350)++0x03
|
|
line.long 0x00 "ID53,Identifier Field 53"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x350)++0x07
|
|
line.long 0x00 "DATA0-3_53,Data Field 0-3 53"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_53,Data Field 4-7 53"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x360)++0x03 "Message Buffer Register 54"
|
|
line.long 0x00 "C/S54,Control and Status 54"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x360)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x360)++0x03
|
|
line.long 0x00 "ID54,Identifier Field 54"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x360)++0x03
|
|
line.long 0x00 "ID54,Identifier Field 54"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x360)++0x07
|
|
line.long 0x00 "DATA0-3_54,Data Field 0-3 54"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_54,Data Field 4-7 54"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x370)++0x03 "Message Buffer Register 55"
|
|
line.long 0x00 "C/S55,Control and Status 55"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x370)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x370)++0x03
|
|
line.long 0x00 "ID55,Identifier Field 55"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x370)++0x03
|
|
line.long 0x00 "ID55,Identifier Field 55"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x370)++0x07
|
|
line.long 0x00 "DATA0-3_55,Data Field 0-3 55"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_55,Data Field 4-7 55"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x380)++0x03 "Message Buffer Register 56"
|
|
line.long 0x00 "C/S56,Control and Status 56"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x380)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x380)++0x03
|
|
line.long 0x00 "ID56,Identifier Field 56"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x380)++0x03
|
|
line.long 0x00 "ID56,Identifier Field 56"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x380)++0x07
|
|
line.long 0x00 "DATA0-3_56,Data Field 0-3 56"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_56,Data Field 4-7 56"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x390)++0x03 "Message Buffer Register 57"
|
|
line.long 0x00 "C/S57,Control and Status 57"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x390)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x390)++0x03
|
|
line.long 0x00 "ID57,Identifier Field 57"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x390)++0x03
|
|
line.long 0x00 "ID57,Identifier Field 57"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x390)++0x07
|
|
line.long 0x00 "DATA0-3_57,Data Field 0-3 57"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_57,Data Field 4-7 57"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3A0)++0x03 "Message Buffer Register 58"
|
|
line.long 0x00 "C/S58,Control and Status 58"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3A0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3A0)++0x03
|
|
line.long 0x00 "ID58,Identifier Field 58"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3A0)++0x03
|
|
line.long 0x00 "ID58,Identifier Field 58"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3A0)++0x07
|
|
line.long 0x00 "DATA0-3_58,Data Field 0-3 58"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_58,Data Field 4-7 58"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3B0)++0x03 "Message Buffer Register 59"
|
|
line.long 0x00 "C/S59,Control and Status 59"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3B0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3B0)++0x03
|
|
line.long 0x00 "ID59,Identifier Field 59"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3B0)++0x03
|
|
line.long 0x00 "ID59,Identifier Field 59"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3B0)++0x07
|
|
line.long 0x00 "DATA0-3_59,Data Field 0-3 59"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_59,Data Field 4-7 59"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3C0)++0x03 "Message Buffer Register 60"
|
|
line.long 0x00 "C/S60,Control and Status 60"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3C0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3C0)++0x03
|
|
line.long 0x00 "ID60,Identifier Field 60"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3C0)++0x03
|
|
line.long 0x00 "ID60,Identifier Field 60"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3C0)++0x07
|
|
line.long 0x00 "DATA0-3_60,Data Field 0-3 60"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_60,Data Field 4-7 60"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3D0)++0x03 "Message Buffer Register 61"
|
|
line.long 0x00 "C/S61,Control and Status 61"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3D0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3D0)++0x03
|
|
line.long 0x00 "ID61,Identifier Field 61"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3D0)++0x03
|
|
line.long 0x00 "ID61,Identifier Field 61"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3D0)++0x07
|
|
line.long 0x00 "DATA0-3_61,Data Field 0-3 61"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_61,Data Field 4-7 61"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3E0)++0x03 "Message Buffer Register 62"
|
|
line.long 0x00 "C/S62,Control and Status 62"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3E0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3E0)++0x03
|
|
line.long 0x00 "ID62,Identifier Field 62"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3E0)++0x03
|
|
line.long 0x00 "ID62,Identifier Field 62"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3E0)++0x07
|
|
line.long 0x00 "DATA0-3_62,Data Field 0-3 62"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_62,Data Field 4-7 62"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
group.long (0x0080+0x3F0)++0x03 "Message Buffer Register 63"
|
|
line.long 0x00 "C/S63,Control and Status 63"
|
|
hexmask.long.byte 0x00 24.--27. 1. " CODE ,Message buffer code"
|
|
bitfld.long 0x00 22. " SRR ,Substitute remote request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21. " IDE ,ID extended bit" "Standard,Extended"
|
|
bitfld.long 0x00 20. " RTR ,Remote transmission request" "Data frame,Remote frame"
|
|
textline " "
|
|
hexmask.long.byte 0x00 16.--19. 1. " LENGTH ,Length of data in bytes"
|
|
hexmask.long.word 0x00 00.--15. 1. " TIMESTAMP ,Free-running counter time stamp"
|
|
if (((data.long(d:(0x53FE8000+0x0080+0x3F0)))&0x00200000)==0x00000000)
|
|
group.long (0x0084+0x3F0)++0x03
|
|
line.long 0x00 "ID63,Identifier Field 63"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.word 0x00 18.--28. 1. " ID ,Standard frame identifier"
|
|
else
|
|
group.long (0x0084+0x3F0)++0x03
|
|
line.long 0x00 "ID63,Identifier Field 63"
|
|
bitfld.long 0x00 29.--31. " PRIO ,Local priority" "0,1,2,3,4,5,6,7"
|
|
hexmask.long 0x00 00.--28. 1. " ID ,Extended Frame identifier"
|
|
endif
|
|
group.long (0x0088+0x3F0)++0x07
|
|
line.long 0x00 "DATA0-3_63,Data Field 0-3 63"
|
|
hexmask.long.byte 0x00 24.--31. 1. " DATA0 ,Data Byte 0"
|
|
hexmask.long.byte 0x00 16.--23. 1. " DATA1 ,Data Byte 1"
|
|
hexmask.long.byte 0x00 08.--15. 1. " DATA2 ,Data Byte 2"
|
|
hexmask.long.byte 0x00 00.--07. 1. " DATA3 ,Data Byte 3"
|
|
line.long 0x04 "DATA4-7_63,Data Field 4-7 63"
|
|
hexmask.long.byte 0x04 24.--31. 1. " DATA4 ,Data Byte 4"
|
|
hexmask.long.byte 0x04 16.--23. 1. " DATA5 ,Data Byte 5"
|
|
hexmask.long.byte 0x04 08.--15. 1. " DATA6 ,Data Byte 6"
|
|
hexmask.long.byte 0x04 00.--07. 1. " DATA7 ,Data Byte 7"
|
|
tree.end
|
|
width 10.
|
|
tree "Common Registers"
|
|
group.long 0x0000++0x0b
|
|
line.long 0x00 "MCR,Module Configuration Register"
|
|
bitfld.long 0x00 31. " MDIS ,Module disable" "No,Yes"
|
|
bitfld.long 0x00 30. " FRZ ,Freeze enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " FEN ,FIFO feature enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " HALT ,FlexCAN freeze mode" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 27. " NOT_RDY ,FlexCAN not ready" "Normal/listen-only/loopback,Disable/doze/stop/freeze"
|
|
bitfld.long 0x00 26. " WAK_MSK ,Wake-up interrupt mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " SOFT_RST ,Soft reset" "No reset,Reset"
|
|
bitfld.long 0x00 24. " FRZ_ACK ,Freeze mode acknowledge" "Not acknowledged,Acknowledged"
|
|
textline " "
|
|
bitfld.long 0x00 23. " SUPV ,Supervisor mode" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " SLF_WAK ,Self wake-up" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " WRN_EN ,Warning Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " LPM_ACK ,Low power mode acknowledge" "No low-power,Disable/doze/stop"
|
|
textline " "
|
|
bitfld.long 0x00 19. " WAK_SRC ,Wake-up source" "Unfiltered Rx,Filtered Rx"
|
|
bitfld.long 0x00 18. " DOZE ,Doze mode enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRX_DIS ,Self Reception Disable" "No,Yes"
|
|
bitfld.long 0x00 16. " BCC ,Backwards Compatibility Configuration" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " LPRIO_EN ,Local priority feature enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " AEN ,Tx abort feature enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " IDAM ,Format of the elements of the Rx FIFO filter table" "A,B,C,D"
|
|
hexmask.long.byte 0x00 00.--05. 1. " MAXMB ,Maximum number of message buffers"
|
|
line.long 0x04 "CTRL,Control Register"
|
|
hexmask.long.byte 0x04 24.--31. 1. " PRESDIV ,Prescaler division factor"
|
|
bitfld.long 0x04 22.--23. " RJW ,Resync jump width" "1,2,3,4"
|
|
textline " "
|
|
bitfld.long 0x04 19.--21. " PSEG1 ,Phase Buffer Segment 1" "1,2,3,4,5,6,7,8"
|
|
bitfld.long 0x04 16.--18. " PSEG2 ,Phase Buffer Segment 2" "1,2,3,4,5,6,7,8"
|
|
textline " "
|
|
bitfld.long 0x04 15. " BOFF_MSK , Bus off mask" "Disabled,Enabled"
|
|
bitfld.long 0x04 14. " ERR_MSK , Error mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 13. " CLK_SRC ,CAN engine clock source" "Osc clk,Bus clk"
|
|
bitfld.long 0x04 12. " LPB ,Loop back" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 11. " TWRN_MSK ,Tx Warning interrupt mask" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " RWRN_MSK ,Rx Warning Interrupt Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 07. " SMP ,Sampling mode" "1 sample,3 samples"
|
|
bitfld.long 0x04 06. " BOFF_REC ,Bus off recovery mode" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x04 05. " TSYN ,Timer sync mode" "Disabled,Enabled"
|
|
bitfld.long 0x04 04. " LBUF ,Lowest buffer transmitted first" "With highest priority,Lowest number"
|
|
textline " "
|
|
bitfld.long 0x04 03. " LOM ,Listen-only mode" "Disabled,Enabled"
|
|
bitfld.long 0x04 00.--02. " PROPSEG ,Propagation segment" "1,2,3,4,5,6,7,8"
|
|
line.long 0x08 "TIMER,Free-Running Timer Register"
|
|
hexmask.long.word 0x08 00.--15. 1. " TIMER ,Timer value"
|
|
group.long 0x0010++0x0F
|
|
line.long 0x00 "RXGMASK,Rx Global Mask Register"
|
|
bitfld.long 0x00 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x00 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x00 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x00 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x00 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x00 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x00 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x00 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x00 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x00 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x00 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x00 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x00 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x00 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x00 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x00 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x00 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x00 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x00 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x00 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x00 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x00 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x00 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x00 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x00 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x00 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x00 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x00 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x00 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x04 "RX14MASK,Rx Buffer 14 Mask Register"
|
|
bitfld.long 0x04 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x04 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x04 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x04 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x04 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x04 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x04 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x04 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x04 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x04 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x04 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x04 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x04 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x04 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x04 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x04 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x04 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x04 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x04 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x04 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x04 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x04 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x04 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x04 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x04 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x04 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x04 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x04 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x04 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x08 "RX15MASK,Rx Buffer 15 Mask Register"
|
|
bitfld.long 0x08 28. " MI[28:0] ,Standard and Extended ID mask bit 28" "0,1"
|
|
bitfld.long 0x08 27. ",Standard and Extended ID mask bit 27" "0,1"
|
|
bitfld.long 0x08 26. ",Standard and Extended ID mask bit 26" "0,1"
|
|
bitfld.long 0x08 25. ",Standard and Extended ID mask bit 25" "0,1"
|
|
bitfld.long 0x08 24. ",Standard and Extended ID mask bit 24" "0,1"
|
|
bitfld.long 0x08 23. ",Standard and Extended ID mask bit 23" "0,1"
|
|
bitfld.long 0x08 22. ",Standard and Extended ID mask bit 22" "0,1"
|
|
bitfld.long 0x08 21. ",Standard and Extended ID mask bit 21" "0,1"
|
|
bitfld.long 0x08 20. ",Standard and Extended ID mask bit 20" "0,1"
|
|
bitfld.long 0x08 19. ",Standard and Extended ID mask bit 19" "0,1"
|
|
bitfld.long 0x08 18. ",Standard and Extended ID mask bit 18" "0,1"
|
|
bitfld.long 0x08 17. ",Extended ID mask bit 17" "0,1"
|
|
bitfld.long 0x08 16. ",Extended ID mask bit 16" "0,1"
|
|
bitfld.long 0x08 15. ",Extended ID mask bit 15" "0,1"
|
|
bitfld.long 0x08 14. ",Extended ID mask bit 14" "0,1"
|
|
bitfld.long 0x08 13. ",Extended ID mask bit 13" "0,1"
|
|
bitfld.long 0x08 12. ",Extended ID mask bit 12" "0,1"
|
|
bitfld.long 0x08 11. ",Extended ID mask bit 11" "0,1"
|
|
bitfld.long 0x08 10. ",Extended ID mask bit 10" "0,1"
|
|
bitfld.long 0x08 09. ",Extended ID mask bit 9" "0,1"
|
|
bitfld.long 0x08 08. ",Extended ID mask bit 8" "0,1"
|
|
bitfld.long 0x08 07. ",Extended ID mask bit 7" "0,1"
|
|
bitfld.long 0x08 06. ",Extended ID mask bit 6" "0,1"
|
|
bitfld.long 0x08 05. ",Extended ID mask bit 5" "0,1"
|
|
bitfld.long 0x08 04. ",Extended ID mask bit 4" "0,1"
|
|
bitfld.long 0x08 03. ",Extended ID mask bit 3" "0,1"
|
|
bitfld.long 0x08 02. ",Extended ID mask bit 2" "0,1"
|
|
bitfld.long 0x08 01. ",Extended ID mask bit 1" "0,1"
|
|
bitfld.long 0x08 00. ",Extended ID mask bit 0" "0,1"
|
|
line.long 0x0C "ECR,Error Counter Register"
|
|
hexmask.long.byte 0x0C 08.--15. 1. " RX_ERR_COUNTER ,Rx Error Counter"
|
|
hexmask.long.byte 0x0C 00.--07. 1. " TX_ERR_COUNTER ,Tx Error Counter"
|
|
hgroup.long 0x0020++0x03
|
|
hide.long 0x00 "ESR,Error and Status Register"
|
|
in
|
|
group.long 0x0028++0x03
|
|
line.long 0x00 "IMASK1,Interrupt Masks Register 1"
|
|
bitfld.long 0x00 31. " BUF31M ,Buffer 31 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " BUF30M ,Buffer 30 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " BUF29M ,Buffer 29 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " BUF28M ,Buffer 28 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 27. " BUF27M ,Buffer 27 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 26. " BUF26M ,Buffer 26 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " BUF25M ,Buffer 25 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 24. " BUF24M ,Buffer 24 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 23. " BUF23M ,Buffer 23 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " BUF22M ,Buffer 22 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " BUF21M ,Buffer 21 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " BUF20M ,Buffer 20 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " BUF19M ,Buffer 19 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " BUF18M ,Buffer 18 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " BUF17M ,Buffer 17 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " BUF16M ,Buffer 16 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " BUF15M ,Buffer 15 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " BUF14M ,Buffer 14 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " BUF13M ,Buffer 13 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " BUF12M ,Buffer 12 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BUF11M ,Buffer 11 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BUF10M ,Buffer 10 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 09. " BUF9M ,Buffer 9 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 08. " BUF8M ,Buffer 8 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 07. " BUF7M ,Buffer 7 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 06. " BUF6M ,Buffer 6 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 05. " BUF5M ,Buffer 5 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 04. " BUF4M ,Buffer 4 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 03. " BUF3M ,Buffer 3 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 02. " BUF2M ,Buffer 2 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 01. " BUF1M ,Buffer 1 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 00. " BUF0M ,Buffer 0 MB Mask" "Disabled,Enabled"
|
|
if (((data.long(asd:0x53FE8000))&0x20000000)==0x00)
|
|
group.long 0x0030++0x03
|
|
line.long 0x00 "IFLAG1,Interrupt Flags 1 Register"
|
|
eventfld.long 0x00 31. " BUF31I ,Buffer 31 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF30I ,Buffer 30 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF29I ,Buffer 29 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF28I ,Buffer 28 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF27I ,Buffer 27 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF26I ,Buffer 26 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF25I ,Buffer 25 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF24I ,Buffer 24 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF23I ,Buffer 23 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF22I ,Buffer 22 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF21I ,Buffer 21 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF20I ,Buffer 20 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF19I ,Buffer 19 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF18I ,Buffer 18 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF17I ,Buffer 17 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF16I ,Buffer 16 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF15I ,Buffer 15 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF14I ,Buffer 14 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF13I ,Buffer 13 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF12I ,Buffer 12 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF11I ,Buffer 11 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF10I ,Buffer 10 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 09. " BUF9I ,Buffer 9 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 08. " BUF8I ,Buffer 8 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 07. " BUF7I ,Buffer 7 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 06. " BUF6I ,Buffer 6 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 05. " BUF5I ,Buffer 5 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 04. " BUF4I ,Buffer 4 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 03. " BUF3I ,Buffer 3 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 02. " BUF2I ,Buffer 2 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 01. " BUF1I ,Buffer 1 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 00. " BUF0I ,Buffer 0 MB Interrupt" "Not occurred,Occurred"
|
|
else
|
|
group.long 0x0030++0x03
|
|
line.long 0x00 "IFLAG1,Interrupt Flags 1 Register"
|
|
eventfld.long 0x00 31. " BUF31I ,Buffer 31 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF30I ,Buffer 30 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF29I ,Buffer 29 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF28I ,Buffer 28 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF27I ,Buffer 27 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF26I ,Buffer 26 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF25I ,Buffer 25 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF24I ,Buffer 24 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF23I ,Buffer 23 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF22I ,Buffer 22 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF21I ,Buffer 21 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF20I ,Buffer 20 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF19I ,Buffer 19 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF18I ,Buffer 18 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF17I ,Buffer 17 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF16I ,Buffer 16 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF15I ,Buffer 15 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF14I ,Buffer 14 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF13I ,Buffer 13 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF12I ,Buffer 12 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF11I ,Buffer 11 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF10I ,Buffer 10 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 09. " BUF9I ,Buffer 9 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 08. " BUF8I ,Buffer 8 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 07. " BUF7I ,FIFO overflow condition" "No overflow,Overflow"
|
|
textline " "
|
|
eventfld.long 0x00 06. " BUF6I ,4 out of 6 buffers of the FIFO are already occupied" "Not occupied,Occupied"
|
|
textline " "
|
|
eventfld.long 0x00 05. " BUF5I ,Least one frame is available to be read from the FIFO" "Not available,Available"
|
|
endif
|
|
group.long 0x0024++0x03
|
|
line.long 0x00 "IMASK2,Interrupt Mask Register 2"
|
|
bitfld.long 0x00 31. " BUF63M ,Buffer 63 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " BUF62M ,Buffer 62 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " BUF61M ,Buffer 61 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " BUF60M ,Buffer 60 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 27. " BUF59M ,Buffer 59 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 26. " BUF58M ,Buffer 58 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " BUF57M ,Buffer 57 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 24. " BUF56M ,Buffer 56 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 23. " BUF55M ,Buffer 55 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " BUF54M ,Buffer 54 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " BUF53M ,Buffer 53 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " BUF52M ,Buffer 52 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " BUF51M ,Buffer 51 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " BUF50M ,Buffer 50 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " BUF49M ,Buffer 49 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " BUF48M ,Buffer 48 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " BUF47M ,Buffer 47 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " BUF46M ,Buffer 46 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " BUF45M ,Buffer 45 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " BUF44M ,Buffer 44 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BUF43M ,Buffer 43 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BUF42M ,Buffer 42 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " BUF41M ,Buffer 41 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " BUF40M ,Buffer 40 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " BUF39M ,Buffer 39 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " BUF38M ,Buffer 38 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " BUF37M ,Buffer 37 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " BUF36M ,Buffer 36 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " BUF35M ,Buffer 35 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " BUF34M ,Buffer 34 MB Mask" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " BUF33M ,Buffer 33 MB Mask" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " BUF32M ,Buffer 32 MB Mask" "Disabled,Enabled"
|
|
group.long 0x002c++0x03
|
|
line.long 0x00 "IFLAG2,Interrupt Flags 2 Register"
|
|
eventfld.long 0x00 31. " BUF63I ,Buffer 63 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " BUF62I ,Buffer 62 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " BUF61I ,Buffer 61 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " BUF60I ,Buffer 60 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " BUF59I ,Buffer 59 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " BUF58I ,Buffer 58 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " BUF57I ,Buffer 57 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " BUF56I ,Buffer 56 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " BUF55I ,Buffer 55 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " BUF54I ,Buffer 54 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " BUF53I ,Buffer 53 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " BUF52I ,Buffer 52 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BUF51I ,Buffer 51 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " BUF50I ,Buffer 50 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " BUF49I ,Buffer 49 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " BUF48I ,Buffer 48 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " BUF47I ,Buffer 47 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " BUF46I ,Buffer 46 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " BUF45I ,Buffer 45 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " BUF44I ,Buffer 44 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " BUF43I ,Buffer 43 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " BUF42I ,Buffer 42 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 9. " BUF41I ,Buffer 41 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 8. " BUF40I ,Buffer 40 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 7. " BUF39I ,Buffer 39 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 6. " BUF38I ,Buffer 38 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 5. " BUF37I ,Buffer 37 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 4. " BUF36I ,Buffer 36 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 3. " BUF35I ,Buffer 35 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 2. " BUF34I ,Buffer 34 MB Interrupt" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 1. " BUF33I ,Buffer 33 MB Interrupt" "Not occurred,Occurred"
|
|
eventfld.long 0x00 0. " BUF32I ,Buffer 32 MB Interrupt" "Not occurred,Occurred"
|
|
tree.end
|
|
width 9.
|
|
tree "Rx Individual Mask Registers 0-15"
|
|
if (((data.long(d:0x53FE8000+0x80))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x0)++0x3
|
|
line.long 0x0 "RXIMR0,Rx Individual Mask Register 0"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x0)++0x3
|
|
line.long 0x0 "RXIMR0,Rx Individual Mask Register 0"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x90))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x4)++0x3
|
|
line.long 0x0 "RXIMR1,Rx Individual Mask Register 1"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x4)++0x3
|
|
line.long 0x0 "RXIMR1,Rx Individual Mask Register 1"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xA0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x8)++0x3
|
|
line.long 0x0 "RXIMR2,Rx Individual Mask Register 2"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x8)++0x3
|
|
line.long 0x0 "RXIMR2,Rx Individual Mask Register 2"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xB0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC)++0x3
|
|
line.long 0x0 "RXIMR3,Rx Individual Mask Register 3"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC)++0x3
|
|
line.long 0x0 "RXIMR3,Rx Individual Mask Register 3"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xC0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x10)++0x3
|
|
line.long 0x0 "RXIMR4,Rx Individual Mask Register 4"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x10)++0x3
|
|
line.long 0x0 "RXIMR4,Rx Individual Mask Register 4"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xD0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x14)++0x3
|
|
line.long 0x0 "RXIMR5,Rx Individual Mask Register 5"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x14)++0x3
|
|
line.long 0x0 "RXIMR5,Rx Individual Mask Register 5"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xE0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x18)++0x3
|
|
line.long 0x0 "RXIMR6,Rx Individual Mask Register 6"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x18)++0x3
|
|
line.long 0x0 "RXIMR6,Rx Individual Mask Register 6"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0xF0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x1C)++0x3
|
|
line.long 0x0 "RXIMR7,Rx Individual Mask Register 7"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x1C)++0x3
|
|
line.long 0x0 "RXIMR7,Rx Individual Mask Register 7"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x100))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x20)++0x3
|
|
line.long 0x0 "RXIMR8,Rx Individual Mask Register 8"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x20)++0x3
|
|
line.long 0x0 "RXIMR8,Rx Individual Mask Register 8"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x110))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x24)++0x3
|
|
line.long 0x0 "RXIMR9,Rx Individual Mask Register 9"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x24)++0x3
|
|
line.long 0x0 "RXIMR9,Rx Individual Mask Register 9"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x120))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x28)++0x3
|
|
line.long 0x0 "RXIMR10,Rx Individual Mask Register 10"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x28)++0x3
|
|
line.long 0x0 "RXIMR10,Rx Individual Mask Register 10"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x130))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x2C)++0x3
|
|
line.long 0x0 "RXIMR11,Rx Individual Mask Register 11"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x2C)++0x3
|
|
line.long 0x0 "RXIMR11,Rx Individual Mask Register 11"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x140))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x30)++0x3
|
|
line.long 0x0 "RXIMR12,Rx Individual Mask Register 12"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x30)++0x3
|
|
line.long 0x0 "RXIMR12,Rx Individual Mask Register 12"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x150))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x34)++0x3
|
|
line.long 0x0 "RXIMR13,Rx Individual Mask Register 13"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x34)++0x3
|
|
line.long 0x0 "RXIMR13,Rx Individual Mask Register 13"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x160))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x38)++0x3
|
|
line.long 0x0 "RXIMR14,Rx Individual Mask Register 14"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x38)++0x3
|
|
line.long 0x0 "RXIMR14,Rx Individual Mask Register 14"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x170))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x3C)++0x3
|
|
line.long 0x0 "RXIMR15,Rx Individual Mask Register 15"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x3C)++0x3
|
|
line.long 0x0 "RXIMR15,Rx Individual Mask Register 15"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 16-31"
|
|
if (((data.long(d:0x53FE8000+0x180))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x40)++0x3
|
|
line.long 0x0 "RXIMR16,Rx Individual Mask Register 16"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x40)++0x3
|
|
line.long 0x0 "RXIMR16,Rx Individual Mask Register 16"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x190))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x44)++0x3
|
|
line.long 0x0 "RXIMR17,Rx Individual Mask Register 17"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x44)++0x3
|
|
line.long 0x0 "RXIMR17,Rx Individual Mask Register 17"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x48)++0x3
|
|
line.long 0x0 "RXIMR18,Rx Individual Mask Register 18"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x48)++0x3
|
|
line.long 0x0 "RXIMR18,Rx Individual Mask Register 18"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x4C)++0x3
|
|
line.long 0x0 "RXIMR19,Rx Individual Mask Register 19"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x4C)++0x3
|
|
line.long 0x0 "RXIMR19,Rx Individual Mask Register 19"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x50)++0x3
|
|
line.long 0x0 "RXIMR20,Rx Individual Mask Register 20"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x50)++0x3
|
|
line.long 0x0 "RXIMR20,Rx Individual Mask Register 20"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x54)++0x3
|
|
line.long 0x0 "RXIMR21,Rx Individual Mask Register 21"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x54)++0x3
|
|
line.long 0x0 "RXIMR21,Rx Individual Mask Register 21"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x58)++0x3
|
|
line.long 0x0 "RXIMR22,Rx Individual Mask Register 22"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x58)++0x3
|
|
line.long 0x0 "RXIMR22,Rx Individual Mask Register 22"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x1F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x5C)++0x3
|
|
line.long 0x0 "RXIMR23,Rx Individual Mask Register 23"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x5C)++0x3
|
|
line.long 0x0 "RXIMR23,Rx Individual Mask Register 23"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x200))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x60)++0x3
|
|
line.long 0x0 "RXIMR24,Rx Individual Mask Register 24"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x60)++0x3
|
|
line.long 0x0 "RXIMR24,Rx Individual Mask Register 24"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x210))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x64)++0x3
|
|
line.long 0x0 "RXIMR25,Rx Individual Mask Register 25"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x64)++0x3
|
|
line.long 0x0 "RXIMR25,Rx Individual Mask Register 25"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x220))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x68)++0x3
|
|
line.long 0x0 "RXIMR26,Rx Individual Mask Register 26"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x68)++0x3
|
|
line.long 0x0 "RXIMR26,Rx Individual Mask Register 26"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x230))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x6C)++0x3
|
|
line.long 0x0 "RXIMR27,Rx Individual Mask Register 27"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x6C)++0x3
|
|
line.long 0x0 "RXIMR27,Rx Individual Mask Register 27"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x240))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x70)++0x3
|
|
line.long 0x0 "RXIMR28,Rx Individual Mask Register 28"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x70)++0x3
|
|
line.long 0x0 "RXIMR28,Rx Individual Mask Register 28"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x250))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x74)++0x3
|
|
line.long 0x0 "RXIMR29,Rx Individual Mask Register 29"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x74)++0x3
|
|
line.long 0x0 "RXIMR29,Rx Individual Mask Register 29"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x260))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x78)++0x3
|
|
line.long 0x0 "RXIMR30,Rx Individual Mask Register 30"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x78)++0x3
|
|
line.long 0x0 "RXIMR30,Rx Individual Mask Register 30"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x270))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x7C)++0x3
|
|
line.long 0x0 "RXIMR31,Rx Individual Mask Register 31"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x7C)++0x3
|
|
line.long 0x0 "RXIMR31,Rx Individual Mask Register 31"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 32-47"
|
|
if (((data.long(d:0x53FE8000+0x280))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x80)++0x3
|
|
line.long 0x0 "RXIMR32,Rx Individual Mask Register 32"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x80)++0x3
|
|
line.long 0x0 "RXIMR32,Rx Individual Mask Register 32"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x290))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x84)++0x3
|
|
line.long 0x0 "RXIMR33,Rx Individual Mask Register 33"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x84)++0x3
|
|
line.long 0x0 "RXIMR33,Rx Individual Mask Register 33"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x88)++0x3
|
|
line.long 0x0 "RXIMR34,Rx Individual Mask Register 34"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x88)++0x3
|
|
line.long 0x0 "RXIMR34,Rx Individual Mask Register 34"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x8C)++0x3
|
|
line.long 0x0 "RXIMR35,Rx Individual Mask Register 35"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x8C)++0x3
|
|
line.long 0x0 "RXIMR35,Rx Individual Mask Register 35"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x90)++0x3
|
|
line.long 0x0 "RXIMR36,Rx Individual Mask Register 36"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x90)++0x3
|
|
line.long 0x0 "RXIMR36,Rx Individual Mask Register 36"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x94)++0x3
|
|
line.long 0x0 "RXIMR37,Rx Individual Mask Register 37"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x94)++0x3
|
|
line.long 0x0 "RXIMR37,Rx Individual Mask Register 37"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x98)++0x3
|
|
line.long 0x0 "RXIMR38,Rx Individual Mask Register 38"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x98)++0x3
|
|
line.long 0x0 "RXIMR38,Rx Individual Mask Register 38"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x2F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0x9C)++0x3
|
|
line.long 0x0 "RXIMR39,Rx Individual Mask Register 39"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0x9C)++0x3
|
|
line.long 0x0 "RXIMR39,Rx Individual Mask Register 39"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x300))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA0)++0x3
|
|
line.long 0x0 "RXIMR40,Rx Individual Mask Register 40"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA0)++0x3
|
|
line.long 0x0 "RXIMR40,Rx Individual Mask Register 40"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x310))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA4)++0x3
|
|
line.long 0x0 "RXIMR41,Rx Individual Mask Register 41"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA4)++0x3
|
|
line.long 0x0 "RXIMR41,Rx Individual Mask Register 41"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x320))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xA8)++0x3
|
|
line.long 0x0 "RXIMR42,Rx Individual Mask Register 42"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xA8)++0x3
|
|
line.long 0x0 "RXIMR42,Rx Individual Mask Register 42"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x330))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xAC)++0x3
|
|
line.long 0x0 "RXIMR43,Rx Individual Mask Register 43"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xAC)++0x3
|
|
line.long 0x0 "RXIMR43,Rx Individual Mask Register 43"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x340))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB0)++0x3
|
|
line.long 0x0 "RXIMR44,Rx Individual Mask Register 44"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB0)++0x3
|
|
line.long 0x0 "RXIMR44,Rx Individual Mask Register 44"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x350))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB4)++0x3
|
|
line.long 0x0 "RXIMR45,Rx Individual Mask Register 45"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB4)++0x3
|
|
line.long 0x0 "RXIMR45,Rx Individual Mask Register 45"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x360))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xB8)++0x3
|
|
line.long 0x0 "RXIMR46,Rx Individual Mask Register 46"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xB8)++0x3
|
|
line.long 0x0 "RXIMR46,Rx Individual Mask Register 46"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x370))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xBC)++0x3
|
|
line.long 0x0 "RXIMR47,Rx Individual Mask Register 47"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xBC)++0x3
|
|
line.long 0x0 "RXIMR47,Rx Individual Mask Register 47"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
tree "Rx Individual Mask Registers 48-63"
|
|
if (((data.long(d:0x53FE8000+0x380))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC0)++0x3
|
|
line.long 0x0 "RXIMR48,Rx Individual Mask Register 48"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC0)++0x3
|
|
line.long 0x0 "RXIMR48,Rx Individual Mask Register 48"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x390))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC4)++0x3
|
|
line.long 0x0 "RXIMR49,Rx Individual Mask Register 49"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC4)++0x3
|
|
line.long 0x0 "RXIMR49,Rx Individual Mask Register 49"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3A0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xC8)++0x3
|
|
line.long 0x0 "RXIMR50,Rx Individual Mask Register 50"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xC8)++0x3
|
|
line.long 0x0 "RXIMR50,Rx Individual Mask Register 50"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3B0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xCC)++0x3
|
|
line.long 0x0 "RXIMR51,Rx Individual Mask Register 51"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xCC)++0x3
|
|
line.long 0x0 "RXIMR51,Rx Individual Mask Register 51"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3C0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD0)++0x3
|
|
line.long 0x0 "RXIMR52,Rx Individual Mask Register 52"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD0)++0x3
|
|
line.long 0x0 "RXIMR52,Rx Individual Mask Register 52"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3D0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD4)++0x3
|
|
line.long 0x0 "RXIMR53,Rx Individual Mask Register 53"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD4)++0x3
|
|
line.long 0x0 "RXIMR53,Rx Individual Mask Register 53"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3E0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xD8)++0x3
|
|
line.long 0x0 "RXIMR54,Rx Individual Mask Register 54"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xD8)++0x3
|
|
line.long 0x0 "RXIMR54,Rx Individual Mask Register 54"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x3F0))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xDC)++0x3
|
|
line.long 0x0 "RXIMR55,Rx Individual Mask Register 55"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xDC)++0x3
|
|
line.long 0x0 "RXIMR55,Rx Individual Mask Register 55"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x400))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE0)++0x3
|
|
line.long 0x0 "RXIMR56,Rx Individual Mask Register 56"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE0)++0x3
|
|
line.long 0x0 "RXIMR56,Rx Individual Mask Register 56"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x410))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE4)++0x3
|
|
line.long 0x0 "RXIMR57,Rx Individual Mask Register 57"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE4)++0x3
|
|
line.long 0x0 "RXIMR57,Rx Individual Mask Register 57"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x420))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xE8)++0x3
|
|
line.long 0x0 "RXIMR58,Rx Individual Mask Register 58"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xE8)++0x3
|
|
line.long 0x0 "RXIMR58,Rx Individual Mask Register 58"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x430))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xEC)++0x3
|
|
line.long 0x0 "RXIMR59,Rx Individual Mask Register 59"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xEC)++0x3
|
|
line.long 0x0 "RXIMR59,Rx Individual Mask Register 59"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x440))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF0)++0x3
|
|
line.long 0x0 "RXIMR60,Rx Individual Mask Register 60"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF0)++0x3
|
|
line.long 0x0 "RXIMR60,Rx Individual Mask Register 60"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x450))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF4)++0x3
|
|
line.long 0x0 "RXIMR61,Rx Individual Mask Register 61"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF4)++0x3
|
|
line.long 0x0 "RXIMR61,Rx Individual Mask Register 61"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x460))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xF8)++0x3
|
|
line.long 0x0 "RXIMR62,Rx Individual Mask Register 62"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xF8)++0x3
|
|
line.long 0x0 "RXIMR62,Rx Individual Mask Register 62"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
if (((data.long(d:0x53FE8000+0x470))&0x00200000)==0x00000000)
|
|
group.long (0x880+0xFC)++0x3
|
|
line.long 0x0 "RXIMR63,Rx Individual Mask Register 63"
|
|
bitfld.long 0x0 28. " MI[28:18] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
else
|
|
group.long (0x880+0xFC)++0x3
|
|
line.long 0x0 "RXIMR63,Rx Individual Mask Register 63"
|
|
bitfld.long 0x0 28. " MI[28:0] ,Standard ID Mask Bit 28" "0,1"
|
|
bitfld.long 0x0 27. ",Standard ID Mask Bit 27" "0,1"
|
|
bitfld.long 0x0 26. ",Standard ID Mask Bit 26" "0,1"
|
|
bitfld.long 0x0 25. ",Standard ID Mask Bit 25" "0,1"
|
|
bitfld.long 0x0 24. ",Standard ID Mask Bit 24" "0,1"
|
|
bitfld.long 0x0 23. ",Standard ID Mask Bit 23" "0,1"
|
|
bitfld.long 0x0 22. ",Standard ID Mask Bit 22" "0,1"
|
|
bitfld.long 0x0 21. ",Standard ID Mask Bit 21" "0,1"
|
|
bitfld.long 0x0 20. ",Standard ID Mask Bit 20" "0,1"
|
|
bitfld.long 0x0 19. ",Standard ID Mask Bit 19" "0,1"
|
|
bitfld.long 0x0 18. ",Standard ID Mask Bit 18" "0,1"
|
|
bitfld.long 0x0 17. ",Extended ID Mask Bit 17" "0,1"
|
|
bitfld.long 0x0 16. ",Extended ID Mask Bit 16" "0,1"
|
|
bitfld.long 0x0 15. ",Extended ID Mask Bit 15" "0,1"
|
|
bitfld.long 0x0 14. ",Extended ID Mask Bit 14" "0,1"
|
|
bitfld.long 0x0 13. ",Extended ID Mask Bit 13" "0,1"
|
|
bitfld.long 0x0 12. ",Extended ID Mask Bit 12" "0,1"
|
|
bitfld.long 0x0 11. ",Extended ID Mask Bit 11" "0,1"
|
|
bitfld.long 0x0 10. ",Extended ID Mask Bit 10" "0,1"
|
|
bitfld.long 0x0 9. ",Extended ID Mask Bit 9" "0,1"
|
|
bitfld.long 0x0 8. ",Extended ID Mask Bit 8" "0,1"
|
|
bitfld.long 0x0 7. ",Extended ID Mask Bit 7" "0,1"
|
|
bitfld.long 0x0 6. ",Extended ID Mask Bit 6" "0,1"
|
|
bitfld.long 0x0 5. ",Extended ID Mask Bit 5" "0,1"
|
|
bitfld.long 0x0 4. ",Extended ID Mask Bit 4" "0,1"
|
|
bitfld.long 0x0 3. ",Extended ID Mask Bit 3" "0,1"
|
|
bitfld.long 0x0 2. ",Extended ID Mask Bit 2" "0,1"
|
|
bitfld.long 0x0 1. ",Extended ID Mask Bit 1" "0,1"
|
|
bitfld.long 0x0 0. ",Extended ID Mask Bit 0" "0,1"
|
|
endif
|
|
tree.end
|
|
width 0xB
|
|
tree.end
|
|
tree.end
|
|
tree.open "CSPI (Configurable Serial Peripheral Interface)"
|
|
tree "CSPI 1"
|
|
base ad:0x43FA4000
|
|
width 10.
|
|
hgroup.long 0x00++0x03
|
|
hide.long 0x00 "RXDATA1,Receive Data Register 1"
|
|
in
|
|
wgroup.long 0x04++0x03
|
|
line.long 0x00 "TXDATA1,Transmit Data Register 1"
|
|
hexmask.long 0x00 0.--31. 1. " TXDATA ,Transmit Data"
|
|
if ((data.long(asd:0x43FA4000+0x8)&0x02)==0x02)
|
|
group.long 0x08++0x03
|
|
line.long 0x00 "CONREG1,Control Register 1"
|
|
hexmask.long.word 0x00 20.--31. 1. " BURST_LENGTH ,Burst Length"
|
|
bitfld.long 0x00 16.--18. " DATA_RATE ,SPI Data Rate Control" "Div by 4,Div by 8,Div by 16,Div by 32,Div by 64,Div by 128,Div by 256,Div by 512"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " CHIP_SELECT ,Select one of four external SPI Master/Slave Devices" "SS0,SS1,SS2,SS3"
|
|
bitfld.long 0x00 8.--9. " DRCTL ,SPI Data Ready Control" "Ignore,Falling /SPI_RDY,Low level /SPI_RDY,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " SSPOL ,SPI SS Polarity Select" "Low,High"
|
|
bitfld.long 0x00 6. " SSCTL ,SPI SS Wave Form Select" "Only one,Multiple"
|
|
textline " "
|
|
bitfld.long 0x00 5. " PHA ,SPI Clock/Data Phase Control" "Phase 0,Phase 1"
|
|
bitfld.long 0x00 4. " POL ,SPI Clock Polarity Control" "High,Low"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SMC ,Start Mode Control" "SPI b. started,Immediately"
|
|
bitfld.long 0x00 2. " XCH ,SPI Exchange Bit" "Idle,Exchanged/Busy"
|
|
textline " "
|
|
bitfld.long 0x00 1. " MODE ,SPI Function Mode Select" "Slave,Master"
|
|
bitfld.long 0x00 0. " EN ,SPI Module Enable Control" "Disabled,Enabled"
|
|
else
|
|
group.long 0x08++0x03
|
|
line.long 0x00 "CONREG1,Control Register 1"
|
|
hexmask.long.word 0x00 20.--31. 1. " BURST_LENGTH ,Burst Length"
|
|
bitfld.long 0x00 16.--18. " DATA_RATE ,SPI Data Rate Control" "Div by 4,Div by 8,Div by 16,Div by 32,Div by 64,Div by 128,Div by 256,Div by 512"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " CHIP_SELECT ,Select one of four external SPI Master/Slave Devices" "SS0,SS1,SS2,SS3"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SSPOL ,SPI SS Polarity Select" "Low,High"
|
|
bitfld.long 0x00 6. " SSCTL ,SPI SS Wave Form Select" "BURST LENGTH+1,SS edge"
|
|
textline " "
|
|
bitfld.long 0x00 5. " PHA ,SPI Clock/Data Phase Control" "Phase 0,Phase 1"
|
|
bitfld.long 0x00 4. " POL ,SPI Clock Polarity Control" "High,Low"
|
|
textline " "
|
|
bitfld.long 0x00 2. " XCH ,SPI Exchange Bit" "Idle,Exchange or busy"
|
|
textline " "
|
|
bitfld.long 0x00 1. " MODE ,SPI Function Mode Select" "Slave,Master"
|
|
bitfld.long 0x00 0. " EN ,SPI Module Enable Control" "Disabled,Enabled"
|
|
endif
|
|
group.long 0x0c++0x03
|
|
line.long 0x00 "INTREG1,Interrupt Control Register 1"
|
|
bitfld.long 0x00 7. " TCEN ,Transfer Completed Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " ROEN ,RXFIFO Overflow Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " RFEN ,RXFIFO Full Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RHEN ,RXFIFO Half Full Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " RREN ,RXFIFO Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " TFEN ,TXFIFO Full Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " THEN ,TXFIFO Half Empty Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " TEEN ,TXFIFO Empty Interrupt Enable" "Disabled,Enabled"
|
|
group.long 0x10++0x03
|
|
line.long 0x00 "DMAREG1,DMA Control Register 1"
|
|
bitfld.long 0x00 5. " RFDEN ,RXFIFO Full DMA Request Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " RHDEN ,RXFIFO Half Full DMA Request Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " THDEN ,TXFIFO Half Empty DMA Request Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TEDEN ,TXFIFO Empty DMA Request Enable" "Disabled,Enabled"
|
|
group.long 0x14++0x03
|
|
line.long 0x00 "STATREG1,Status Register 1"
|
|
eventfld.long 0x00 7. " TC , Transfer Completed" "In progress,Completed"
|
|
bitfld.long 0x00 6. " RO ,RXFIFO Overflow" "No overflow,Overflow"
|
|
bitfld.long 0x00 5. " RF ,RXFIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RH ,RXFIFO Half Full" "<4,>=4"
|
|
bitfld.long 0x00 3. " RR ,RXFIFO Ready" "No data,>1 word"
|
|
bitfld.long 0x00 2. " TF ,TXFIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 1. " TH ,TXFIFO Half Empty" ">4 words,<=4"
|
|
bitfld.long 0x00 0. " TE ,TXFIFO Empty" "Not empty,Empty"
|
|
group.long 0x18++0x03
|
|
line.long 0x00 "PERIODREG1,Sample Period Control Register 1"
|
|
bitfld.long 0x00 15. " CSRC ,Clock Source Control" "SPI Clock,Low-Frequency Reference Clock"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--14. 1. " SAMPLEPERIOD ,Sample Period Control"
|
|
group.long 0x1c++0x03
|
|
line.long 0x00 "TESTREG1,Test Control Register 1"
|
|
bitfld.long 0x00 15. " SWAP ,Data Swap" "Unchanged,Swapped"
|
|
bitfld.long 0x00 14. " LBC ,Loop Back Control" "Not connected,Connected"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " RXCNT ,RXFIFO Counter" "0 words,1 word,2 words,3 words,4 words,5 words,6 words,7 words,8 words,?..."
|
|
bitfld.long 0x00 0.--3. " TXCNT ,TXFIFO Counter" "0 words,1 word,2 words,3 words,4 words,5 words,6 words,7 words,8 words,?..."
|
|
width 0x0b
|
|
tree.end
|
|
tree "CSPI 2"
|
|
base ad:0x50010000
|
|
width 10.
|
|
hgroup.long 0x00++0x03
|
|
hide.long 0x00 "RXDATA2,Receive Data Register 2"
|
|
in
|
|
wgroup.long 0x04++0x03
|
|
line.long 0x00 "TXDATA2,Transmit Data Register 2"
|
|
hexmask.long 0x00 0.--31. 1. " TXDATA ,Transmit Data"
|
|
if ((data.long(asd:0x50010000+0x8)&0x02)==0x02)
|
|
group.long 0x08++0x03
|
|
line.long 0x00 "CONREG2,Control Register 2"
|
|
hexmask.long.word 0x00 20.--31. 1. " BURST_LENGTH ,Burst Length"
|
|
bitfld.long 0x00 16.--18. " DATA_RATE ,SPI Data Rate Control" "Div by 4,Div by 8,Div by 16,Div by 32,Div by 64,Div by 128,Div by 256,Div by 512"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " CHIP_SELECT ,Select one of four external SPI Master/Slave Devices" "SS0,SS1,SS2,SS3"
|
|
bitfld.long 0x00 8.--9. " DRCTL ,SPI Data Ready Control" "Ignore,Falling /SPI_RDY,Low level /SPI_RDY,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " SSPOL ,SPI SS Polarity Select" "Low,High"
|
|
bitfld.long 0x00 6. " SSCTL ,SPI SS Wave Form Select" "Only one,Multiple"
|
|
textline " "
|
|
bitfld.long 0x00 5. " PHA ,SPI Clock/Data Phase Control" "Phase 0,Phase 1"
|
|
bitfld.long 0x00 4. " POL ,SPI Clock Polarity Control" "High,Low"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SMC ,Start Mode Control" "SPI b. started,Immediately"
|
|
bitfld.long 0x00 2. " XCH ,SPI Exchange Bit" "Idle,Exchanged/Busy"
|
|
textline " "
|
|
bitfld.long 0x00 1. " MODE ,SPI Function Mode Select" "Slave,Master"
|
|
bitfld.long 0x00 0. " EN ,SPI Module Enable Control" "Disabled,Enabled"
|
|
else
|
|
group.long 0x08++0x03
|
|
line.long 0x00 "CONREG2,Control Register 2"
|
|
hexmask.long.word 0x00 20.--31. 1. " BURST_LENGTH ,Burst Length"
|
|
bitfld.long 0x00 16.--18. " DATA_RATE ,SPI Data Rate Control" "Div by 4,Div by 8,Div by 16,Div by 32,Div by 64,Div by 128,Div by 256,Div by 512"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " CHIP_SELECT ,Select one of four external SPI Master/Slave Devices" "SS0,SS1,SS2,SS3"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SSPOL ,SPI SS Polarity Select" "Low,High"
|
|
bitfld.long 0x00 6. " SSCTL ,SPI SS Wave Form Select" "BURST LENGTH+1,SS edge"
|
|
textline " "
|
|
bitfld.long 0x00 5. " PHA ,SPI Clock/Data Phase Control" "Phase 0,Phase 1"
|
|
bitfld.long 0x00 4. " POL ,SPI Clock Polarity Control" "High,Low"
|
|
textline " "
|
|
bitfld.long 0x00 2. " XCH ,SPI Exchange Bit" "Idle,Exchange or busy"
|
|
textline " "
|
|
bitfld.long 0x00 1. " MODE ,SPI Function Mode Select" "Slave,Master"
|
|
bitfld.long 0x00 0. " EN ,SPI Module Enable Control" "Disabled,Enabled"
|
|
endif
|
|
group.long 0x0c++0x03
|
|
line.long 0x00 "INTREG2,Interrupt Control Register 2"
|
|
bitfld.long 0x00 7. " TCEN ,Transfer Completed Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " ROEN ,RXFIFO Overflow Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " RFEN ,RXFIFO Full Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RHEN ,RXFIFO Half Full Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " RREN ,RXFIFO Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " TFEN ,TXFIFO Full Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " THEN ,TXFIFO Half Empty Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " TEEN ,TXFIFO Empty Interrupt Enable" "Disabled,Enabled"
|
|
group.long 0x10++0x03
|
|
line.long 0x00 "DMAREG2,DMA Control Register 2"
|
|
bitfld.long 0x00 5. " RFDEN ,RXFIFO Full DMA Request Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " RHDEN ,RXFIFO Half Full DMA Request Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " THDEN ,TXFIFO Half Empty DMA Request Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TEDEN ,TXFIFO Empty DMA Request Enable" "Disabled,Enabled"
|
|
group.long 0x14++0x03
|
|
line.long 0x00 "STATREG2,Status Register 2"
|
|
eventfld.long 0x00 7. " TC , Transfer Completed" "In progress,Completed"
|
|
bitfld.long 0x00 6. " RO ,RXFIFO Overflow" "No overflow,Overflow"
|
|
bitfld.long 0x00 5. " RF ,RXFIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RH ,RXFIFO Half Full" "<4,>=4"
|
|
bitfld.long 0x00 3. " RR ,RXFIFO Ready" "No data,>1 word"
|
|
bitfld.long 0x00 2. " TF ,TXFIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 1. " TH ,TXFIFO Half Empty" ">4 words,<=4"
|
|
bitfld.long 0x00 0. " TE ,TXFIFO Empty" "Not empty,Empty"
|
|
group.long 0x18++0x03
|
|
line.long 0x00 "PERIODREG2,Sample Period Control Register 2"
|
|
bitfld.long 0x00 15. " CSRC ,Clock Source Control" "SPI Clock,Low-Frequency Reference Clock"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--14. 1. " SAMPLEPERIOD ,Sample Period Control"
|
|
group.long 0x1c++0x03
|
|
line.long 0x00 "TESTREG2,Test Control Register 2"
|
|
bitfld.long 0x00 15. " SWAP ,Data Swap" "Unchanged,Swapped"
|
|
bitfld.long 0x00 14. " LBC ,Loop Back Control" "Not connected,Connected"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " RXCNT ,RXFIFO Counter" "0 words,1 word,2 words,3 words,4 words,5 words,6 words,7 words,8 words,?..."
|
|
bitfld.long 0x00 0.--3. " TXCNT ,TXFIFO Counter" "0 words,1 word,2 words,3 words,4 words,5 words,6 words,7 words,8 words,?..."
|
|
width 0x0b
|
|
tree.end
|
|
tree.end
|
|
tree.open "eSDHC (Enhanced Secure Digital Host Controller)"
|
|
tree "eSDHC 1"
|
|
base ad:0x53FB4000
|
|
width 15.
|
|
group.long 0x00++0xF
|
|
line.long 0x00 "DSADDR,DMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " DS_ADDR[31:2] ,DMA system address"
|
|
line.long 0x04 "BLKATTR,Block Attributes Register"
|
|
hexmask.long.word 0x04 16.--31. 1. " BLKCNT ,Blocks Count For Current Transfer"
|
|
hexmask.long.word 0x04 0.--12. 1. " BLKSZE ,Transfer Block Size"
|
|
line.long 0x08 "CMDARG,Command Argument Register"
|
|
line.long 0x0C "XFERTYP,Transfer Type Register"
|
|
hexmask.long.byte 0x0C 24.--29. 1. " CMDINX ,Command Index"
|
|
bitfld.long 0x0C 22.--23. " CMDTYP ,Command Type" "Normal,Suspend,Resume,Abort"
|
|
textline " "
|
|
bitfld.long 0x0C 21. " DPSEL ,Data Present Select" "No data,Data present"
|
|
bitfld.long 0x0C 20. " CICEN ,Command Index Check Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 19. " CCCEN ,Command CRC Check Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 16.--17. " RSPTYP ,Response Type Select" "No Response,Length 136,Length 48,Length 48 check busy"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " MSBSEL ,Multi / Single Block Select" "Single,Multiple"
|
|
bitfld.long 0x0C 4. " DTDSEL ,Data Transfer Direction Select" "Write,Read"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " AC12EN ,Auto CMD12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 1. " BCEN ,Block Count Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 0. " DMAEN ,DMA Enable" "Disabled,Enabled"
|
|
if (((data.long(ad:0x53FB4000+0x0c))&0x30000)==0x00)
|
|
hgroup.long 0x10++0x03
|
|
hide.long 0x00 "CMDRSP0,Command Response 0"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
elif (((data.long(ad:0x53FB4000+0x0c))&0x30000)==0x10000)
|
|
rgroup.long 0x10++0xF
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R2 response"
|
|
line.long 0x04 "CMDRSP1,Command Response 1"
|
|
hexmask.long 0x04 0.--31. 1. " CMDRSP1 ,R2 response"
|
|
line.long 0x08 "CMDRSP2,Command Response 2"
|
|
hexmask.long 0x08 0.--31. 1. " CMDRSP2 ,R2 response"
|
|
line.long 0x0C "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x0c 0.--23. 1. " CMDRSP3 ,R2[23:0] response"
|
|
elif (((data.long(ad:0x53FB4000+0x0c))&0x30000)==0x20000)
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1/R3/R4/R5/R6 response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
else
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1b/R5b response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP3 ,R1b response"
|
|
endif
|
|
group.long 0x20++0x3
|
|
line.long 0x00 "DATPORT,Buffer Data Port Register"
|
|
rgroup.long 0x24++0x3
|
|
line.long 0x00 "PRSSTAT,Present State Register"
|
|
bitfld.long 0x00 31. " DLSL[7] ,Line 7 Signal Level" "Low,High"
|
|
bitfld.long 0x00 30. " DLSL[6] ,Line 6 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DLSL[5] ,Line 5 Signal Level" "Low,High"
|
|
bitfld.long 0x00 28. " DLSL[4] ,Line 4 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DLSL[3] ,Line 3 Signal Level" "Low,High"
|
|
bitfld.long 0x00 26. " DLSL[2] ,Line 2 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DLSL[1] ,Line 1 Signal Level" "Low,High"
|
|
bitfld.long 0x00 24. " DLSL[0] ,Line 0 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 23. " CLSL ,CMD Line Signal Level" "Pull-down,Pull-up"
|
|
bitfld.long 0x00 19. " WPSPL ,Write Protect Switch Pin Level" "Protected,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " CDPL ,Card Detect Pin Level" "No card,Card present"
|
|
bitfld.long 0x00 16. " CINS ,Card Inserted" "No card/Reset/Power on,Card inserted"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BREN ,Buffer Read Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BWEN ,Buffer Write Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RTA ,Read Transfer Active" "No data,Transferring"
|
|
bitfld.long 0x00 8. " WTA ,Write Transfer Active" "No data,Transferring"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SDOFF ,SD Clock Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 6. " PEROFF ,IPG_PERCLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 5. " HCKOFF ,HCLK Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 4. " IPGOFF ,IPG_CLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SDSTB ,SD clock stable" "Not stable,Stable"
|
|
bitfld.long 0x00 2. " DLA ,Data Line Active" "Inactive,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CDIHB ,Command Inhibit (DAT)" "Can issue,Cannot issue"
|
|
bitfld.long 0x00 0. " CIHB ,Command Inhibit (CMD)" "Can issue,Cannot issue"
|
|
group.long 0x28++0x13
|
|
line.long 0x00 "PROCTL,Protocol Control Register"
|
|
bitfld.long 0x00 26. " WECRM ,Wakeup Event Enable On SD Card Removal" "Disabled,Enabled"
|
|
bitfld.long 0x00 25. " WECINS ,Wakeup Event Enable On SD Card Insertion" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " WECINT ,Wakeup Event Enable On Card Interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " IABG ,Interrupt At Block Gap" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " RWCTL ,Read Wait Control" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " CREQ ,Continue Request" "No effect,Restart"
|
|
textline " "
|
|
bitfld.long 0x00 16. " SABGREQ ,Stop At Block Gap Request" "Transfer,Stop"
|
|
bitfld.long 0x00 8.--9. " DMAS ,DMA Select" "No/Simple DMA,ADMA1,ADMA2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " CDSS ,Card Detect Signal Selection" "Level,Test level"
|
|
bitfld.long 0x00 6. " CDTL ,Card Detect Test Level" "No card,Card present"
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " EMODE ,Endian Mode" "Big endian,Half word big endian,Little endian,?..."
|
|
bitfld.long 0x00 3. " D3CD ,DAT3 as Card Detection Pin" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1.--2. " DTW ,Data Transfer Width" "1-bit,4-bit,8-bit,?..."
|
|
bitfld.long 0x00 0. " LCTL ,LED Control" "Off,On"
|
|
line.long 0x04 "SYSCTL,System Control Register"
|
|
bitfld.long 0x04 27. " INITA ,Initialization Active" "No effect,Active"
|
|
textline " "
|
|
bitfld.long 0x04 26. " RSTD ,Software Reset For DAT Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 25. " RSTC ,Software Reset For CMD Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 24. " RSTA ,Software Reset For ALL" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 16.--19. " DTOCV ,Data Timeout Counter Value" "SDCLKx2^13,SDCLKx2^14,SDCLKx2^15,SDCLKx2^16,SDCLKx2^17,SDCLKx2^18,SDCLKx2^19,SDCLKx2^20,SDCLKx2^21,SDCLKx2^22,SDCLKx2^23,SDCLKx2^24,SDCLKx2^25,SDCLKx2^26,SDCLKx2^27,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x04 8.--15. 1. " SDCLKFS ,SDCLK Frequency Select"
|
|
textline " "
|
|
bitfld.long 0x04 4.--7. " DVS ,Divisor" "Divisor by 1,Divisor by 2,Divisor by 3,Divisor by 4,Divisor by 5,Divisor by 6,Divisor by 7,Divisor by 8,Divisor by 9,Divisor by 10,Divisor by 11,Divisor by 12,Divisor by 13,Divisor by 14,Divisor by 15,Divisor by 16"
|
|
textline " "
|
|
bitfld.long 0x04 3. " SDCLKEN ,SD clock enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 2. " PEREN ,Peripheral Clock Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 1. " HCKEN ,HCLK Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 0. " IPGEN ,IPG Clock Enable" "Internally gated off,No auto gated off"
|
|
line.long 0x08 "IRQSTAT,Interrupt Status Register"
|
|
eventfld.long 0x08 28. " DMAE ,DMA Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 24. " AC12E ,Auto CMD12 Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 22. " DEBE ,Data End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 21. " DCE ,Data CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 20. " DTOE ,Data Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 19. " CIE ,Command Index Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 18. " CEBE ,Command End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 17. " CCE ,Command CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 16. " CTOE ,Command Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 8. " CINT ,Card Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 7. " CRM ,Card Removal" "Unstable/Inserted,Removed"
|
|
textline " "
|
|
eventfld.long 0x08 6. " CINS ,Card Insertion" "Unstable/Removed,Inserted"
|
|
textline " "
|
|
eventfld.long 0x08 5. " BRR ,Buffer Read Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 4. " BWR ,Buffer Write Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 3. " DINT ,DMA Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 2. " BGE ,Block Gap Event" "No event,Event occurred"
|
|
textline " "
|
|
eventfld.long 0x08 1. " TC ,Transfer Complete" "Not completed,Completed"
|
|
textline " "
|
|
eventfld.long 0x08 0. " CC ,Command Complete" "Not completed,Completed"
|
|
width 15.
|
|
line.long 0x0C "IRQSTATEN,Interrupt Status Enable Register"
|
|
bitfld.long 0x0C 28. " DMAESEN ,DMA Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 24. " AC12ESEN ,Auto CMD12 Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 22. " DEBESEN ,Data End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 21. " DCESEN ,Data CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 20. " DTOESEN ,Data Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 19. " CIESEN ,Command Index Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 18. " CEBESEN ,Command End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 17. " CCESEN ,Command CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 16. " CTOESEN ,Command Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 8. " CINTSEN ,Card Interrupt Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 7. " CRMSEN ,Card Removal Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 6. " CINSSEN ,Card Insertion Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " BRRSEN ,Buffer Read Ready Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 4. " BWRSEN ,Buffer Write Ready Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 3. " DINTSEN ,DMA Interrupt Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 2. " BGESEN ,Block Gap Event Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 1. " TCSEN ,Transfer Complete Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 0. " CCSEN ,Command Complete Status Enable" "Masked,Enabled"
|
|
line.long 0x10 "IRQSIGEN,Interrupt Signal Enable Register"
|
|
bitfld.long 0x10 28. " DMAEIEN ,DMA Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 24. " AC12EIEN ,Auto CMD12 Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 22. " DEBEIEN ,Data End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 21. " DCEIEN ,Data CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 20. " DTOEIEN ,Data Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 19. " CIEIEN ,Command Index Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 18. " CEBEIEN ,Command End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 17. " CCEIEN ,Command CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 16. " CTOEIEN ,Command Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 8. " CINTIEN ,Card Interrupt Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " CRMIEN ,Card Removal Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 6. " CINSIEN ,Card Insertion Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 5. " BRRIEN ,Buffer Read Ready Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 4. " BWRIEN ,Buffer Write Ready Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " DINTIEN ,DMA Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 2. " BGEIEN ,Block Gap Event Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 1. " TCIEN ,Transfer Complete Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 0. " CCIEN ,Command Complete Interrupt Enable" "Masked,Enabled"
|
|
if (((data.long(ad:0x53FB4000+0x30))&0x1000000)==0x1000000)
|
|
rgroup.long 0x3C++0x3
|
|
line.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
bitfld.long 0x00 7. " CNIBAC12E ,Command Not Issued By Auto CMD12 Error" "No error,Not Issued"
|
|
bitfld.long 0x00 4. " AC12IE ,Auto CMD12 Index Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 3. " AC12CE ,Auto CMD12 CRC Error" "No error,Error"
|
|
bitfld.long 0x00 2. " AC12EBE ,Auto CMD12 End Bit Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 1. " AC12TOE ,Auto CMD12 Timeout Error" "No error,Error"
|
|
bitfld.long 0x00 0. " AC12NE ,Auto CMD12 Not Executed" "Executed,Not executed"
|
|
else
|
|
hgroup.long 0x3C++0x3
|
|
hide.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
endif
|
|
rgroup.long 0x40++0x3
|
|
line.long 0x00 "HOSTCAPBLT,Host Controller Capabilities"
|
|
bitfld.long 0x00 26. " VS18 ,Voltage Support 1.8V" "Not supported,Supported"
|
|
bitfld.long 0x00 25. " VS30 ,Voltage Support 3.0V" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 24. " VS33 ,Voltage Support 3.3V" "Not supported,Supported"
|
|
bitfld.long 0x00 23. " SRS ,Suspend / Resume Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DMAS ,DMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 21. " HSS ,High Speed Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 20. " ADMAS ,ADMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 16.--18. " MBL ,Max Block Length" "512 bytes,1024 bytes,2048 bytes,4096 bytes,?..."
|
|
group.long 0x44++0x3
|
|
line.long 0x00 "WML,Watermark Level Register"
|
|
hexmask.long.byte 0x00 24.--28. 1. " WR_BRST_LEN ,Write Burst Length"
|
|
hexmask.long.byte 0x00 16.--23. 1. " WR_WML ,Write Watermark Level"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--12. 1. " RD_BRST_LEN ,Read Burst Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RD_WML ,Read Watermark Level"
|
|
wgroup.long 0x50++0x3
|
|
line.long 0x00 "FEVT,Force Event Register"
|
|
bitfld.long 0x00 31. " FEVTCINT ,Force Event Card Interrupt" "No effect,Force"
|
|
bitfld.long 0x00 28. " FEVTDMAE ,Force Event DMA Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 24. " FEVTAC12E ,Force Event Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 22. " FEVTDEBE ,Force Event Data End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 21. " FEVTDCE ,Force Event Data CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 20. " FEVTDTOE ,Force Event Data Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 19. " FEVTCIE ,Force Event Command Index Error" "No effect,Force"
|
|
bitfld.long 0x00 18. " FEVTCEBE ,Force Event Command End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 17. " FEVTCCE ,Force Event Command CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 16. " FEVTCTOE ,Force Event Command Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 7. " FEVTCNIBAC12E ,Force Event Command Not Executed By Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 4. " FEVTAC12IE ,Force Event Auto Command 12 Index Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 3. " FEVTAC12EBE ,Force Event Auto Command 12 End Bit Error" "No effect,Force"
|
|
bitfld.long 0x00 2. " FEVTAC12CE ,Force Event Auto Command 12 CRC Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 1. " FEVTAC12TOE ,Force Event Auto Command 12 Time Out Error" "No effect,Force"
|
|
bitfld.long 0x00 0. " FEVTAC12NE ,Force Event Auto Command 12 Not Executed" "No effect,Force"
|
|
rgroup.long 0x54++0x3
|
|
line.long 0x00 "ADMAES,ADMA Error Status Register"
|
|
bitfld.long 0x00 3. " ADMADCE ,ADMA Descriptor Error" "No error,Error"
|
|
bitfld.long 0x00 2. " ADMALME ,ADMA Length Mismatch Error" "No error,Error"
|
|
bitfld.long 0x00 0.--1. " ADMAES ,ADMA Error State" "Stop DMA,Fetch Descriptor,Change Address,Transfer Data"
|
|
group.long 0x58++0x3
|
|
line.long 0x00 "ADSADDR,ADMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " ADS_ADDR[31:0] ,ADMA system address"
|
|
group.long 0xC0++0x03
|
|
line.long 0x00 "VENDOR,Vendor Specific Register"
|
|
bitfld.long 0x00 24.--27. " DBG_SEL[3:0] ,Debug select" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
hexmask.long.byte 0x00 16.--23. 1. " INT_ST_VAL[7:0] ,Internal state value"
|
|
textline " "
|
|
bitfld.long 0x00 1. " VOLT_SEL ,Voltage selection" "Low,High"
|
|
bitfld.long 0x00 0. " EXT_DMA_EN ,External DMA request enable" "Disabled,Enabled"
|
|
rgroup.long 0xfc++0x3
|
|
line.long 0x00 "HCV,Host Controller Version"
|
|
hexmask.long.byte 0x00 8.--15. 1. " VVN[7:0] ,Vendor Version Number"
|
|
hexmask.long.byte 0x00 0.--7. 1. " SVN[7:0] ,Specification Version Number"
|
|
tree.end
|
|
tree "eSDHC 2"
|
|
base ad:0x53FB8000
|
|
width 15.
|
|
group.long 0x00++0xF
|
|
line.long 0x00 "DSADDR,DMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " DS_ADDR[31:2] ,DMA system address"
|
|
line.long 0x04 "BLKATTR,Block Attributes Register"
|
|
hexmask.long.word 0x04 16.--31. 1. " BLKCNT ,Blocks Count For Current Transfer"
|
|
hexmask.long.word 0x04 0.--12. 1. " BLKSZE ,Transfer Block Size"
|
|
line.long 0x08 "CMDARG,Command Argument Register"
|
|
line.long 0x0C "XFERTYP,Transfer Type Register"
|
|
hexmask.long.byte 0x0C 24.--29. 1. " CMDINX ,Command Index"
|
|
bitfld.long 0x0C 22.--23. " CMDTYP ,Command Type" "Normal,Suspend,Resume,Abort"
|
|
textline " "
|
|
bitfld.long 0x0C 21. " DPSEL ,Data Present Select" "No data,Data present"
|
|
bitfld.long 0x0C 20. " CICEN ,Command Index Check Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 19. " CCCEN ,Command CRC Check Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 16.--17. " RSPTYP ,Response Type Select" "No Response,Length 136,Length 48,Length 48 check busy"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " MSBSEL ,Multi / Single Block Select" "Single,Multiple"
|
|
bitfld.long 0x0C 4. " DTDSEL ,Data Transfer Direction Select" "Write,Read"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " AC12EN ,Auto CMD12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 1. " BCEN ,Block Count Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 0. " DMAEN ,DMA Enable" "Disabled,Enabled"
|
|
if (((data.long(ad:0x53FB8000+0x0c))&0x30000)==0x00)
|
|
hgroup.long 0x10++0x03
|
|
hide.long 0x00 "CMDRSP0,Command Response 0"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
elif (((data.long(ad:0x53FB8000+0x0c))&0x30000)==0x10000)
|
|
rgroup.long 0x10++0xF
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R2 response"
|
|
line.long 0x04 "CMDRSP1,Command Response 1"
|
|
hexmask.long 0x04 0.--31. 1. " CMDRSP1 ,R2 response"
|
|
line.long 0x08 "CMDRSP2,Command Response 2"
|
|
hexmask.long 0x08 0.--31. 1. " CMDRSP2 ,R2 response"
|
|
line.long 0x0C "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x0c 0.--23. 1. " CMDRSP3 ,R2[23:0] response"
|
|
elif (((data.long(ad:0x53FB8000+0x0c))&0x30000)==0x20000)
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1/R3/R4/R5/R6 response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
else
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1b/R5b response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP3 ,R1b response"
|
|
endif
|
|
group.long 0x20++0x3
|
|
line.long 0x00 "DATPORT,Buffer Data Port Register"
|
|
rgroup.long 0x24++0x3
|
|
line.long 0x00 "PRSSTAT,Present State Register"
|
|
bitfld.long 0x00 31. " DLSL[7] ,Line 7 Signal Level" "Low,High"
|
|
bitfld.long 0x00 30. " DLSL[6] ,Line 6 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DLSL[5] ,Line 5 Signal Level" "Low,High"
|
|
bitfld.long 0x00 28. " DLSL[4] ,Line 4 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DLSL[3] ,Line 3 Signal Level" "Low,High"
|
|
bitfld.long 0x00 26. " DLSL[2] ,Line 2 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DLSL[1] ,Line 1 Signal Level" "Low,High"
|
|
bitfld.long 0x00 24. " DLSL[0] ,Line 0 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 23. " CLSL ,CMD Line Signal Level" "Pull-down,Pull-up"
|
|
bitfld.long 0x00 19. " WPSPL ,Write Protect Switch Pin Level" "Protected,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " CDPL ,Card Detect Pin Level" "No card,Card present"
|
|
bitfld.long 0x00 16. " CINS ,Card Inserted" "No card/Reset/Power on,Card inserted"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BREN ,Buffer Read Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BWEN ,Buffer Write Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RTA ,Read Transfer Active" "No data,Transferring"
|
|
bitfld.long 0x00 8. " WTA ,Write Transfer Active" "No data,Transferring"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SDOFF ,SD Clock Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 6. " PEROFF ,IPG_PERCLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 5. " HCKOFF ,HCLK Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 4. " IPGOFF ,IPG_CLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SDSTB ,SD clock stable" "Not stable,Stable"
|
|
bitfld.long 0x00 2. " DLA ,Data Line Active" "Inactive,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CDIHB ,Command Inhibit (DAT)" "Can issue,Cannot issue"
|
|
bitfld.long 0x00 0. " CIHB ,Command Inhibit (CMD)" "Can issue,Cannot issue"
|
|
group.long 0x28++0x13
|
|
line.long 0x00 "PROCTL,Protocol Control Register"
|
|
bitfld.long 0x00 26. " WECRM ,Wakeup Event Enable On SD Card Removal" "Disabled,Enabled"
|
|
bitfld.long 0x00 25. " WECINS ,Wakeup Event Enable On SD Card Insertion" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " WECINT ,Wakeup Event Enable On Card Interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " IABG ,Interrupt At Block Gap" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " RWCTL ,Read Wait Control" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " CREQ ,Continue Request" "No effect,Restart"
|
|
textline " "
|
|
bitfld.long 0x00 16. " SABGREQ ,Stop At Block Gap Request" "Transfer,Stop"
|
|
bitfld.long 0x00 8.--9. " DMAS ,DMA Select" "No/Simple DMA,ADMA1,ADMA2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " CDSS ,Card Detect Signal Selection" "Level,Test level"
|
|
bitfld.long 0x00 6. " CDTL ,Card Detect Test Level" "No card,Card present"
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " EMODE ,Endian Mode" "Big endian,Half word big endian,Little endian,?..."
|
|
bitfld.long 0x00 3. " D3CD ,DAT3 as Card Detection Pin" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1.--2. " DTW ,Data Transfer Width" "1-bit,4-bit,8-bit,?..."
|
|
bitfld.long 0x00 0. " LCTL ,LED Control" "Off,On"
|
|
line.long 0x04 "SYSCTL,System Control Register"
|
|
bitfld.long 0x04 27. " INITA ,Initialization Active" "No effect,Active"
|
|
textline " "
|
|
bitfld.long 0x04 26. " RSTD ,Software Reset For DAT Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 25. " RSTC ,Software Reset For CMD Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 24. " RSTA ,Software Reset For ALL" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 16.--19. " DTOCV ,Data Timeout Counter Value" "SDCLKx2^13,SDCLKx2^14,SDCLKx2^15,SDCLKx2^16,SDCLKx2^17,SDCLKx2^18,SDCLKx2^19,SDCLKx2^20,SDCLKx2^21,SDCLKx2^22,SDCLKx2^23,SDCLKx2^24,SDCLKx2^25,SDCLKx2^26,SDCLKx2^27,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x04 8.--15. 1. " SDCLKFS ,SDCLK Frequency Select"
|
|
textline " "
|
|
bitfld.long 0x04 4.--7. " DVS ,Divisor" "Divisor by 1,Divisor by 2,Divisor by 3,Divisor by 4,Divisor by 5,Divisor by 6,Divisor by 7,Divisor by 8,Divisor by 9,Divisor by 10,Divisor by 11,Divisor by 12,Divisor by 13,Divisor by 14,Divisor by 15,Divisor by 16"
|
|
textline " "
|
|
bitfld.long 0x04 3. " SDCLKEN ,SD clock enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 2. " PEREN ,Peripheral Clock Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 1. " HCKEN ,HCLK Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 0. " IPGEN ,IPG Clock Enable" "Internally gated off,No auto gated off"
|
|
line.long 0x08 "IRQSTAT,Interrupt Status Register"
|
|
eventfld.long 0x08 28. " DMAE ,DMA Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 24. " AC12E ,Auto CMD12 Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 22. " DEBE ,Data End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 21. " DCE ,Data CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 20. " DTOE ,Data Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 19. " CIE ,Command Index Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 18. " CEBE ,Command End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 17. " CCE ,Command CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 16. " CTOE ,Command Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 8. " CINT ,Card Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 7. " CRM ,Card Removal" "Unstable/Inserted,Removed"
|
|
textline " "
|
|
eventfld.long 0x08 6. " CINS ,Card Insertion" "Unstable/Removed,Inserted"
|
|
textline " "
|
|
eventfld.long 0x08 5. " BRR ,Buffer Read Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 4. " BWR ,Buffer Write Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 3. " DINT ,DMA Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 2. " BGE ,Block Gap Event" "No event,Event occurred"
|
|
textline " "
|
|
eventfld.long 0x08 1. " TC ,Transfer Complete" "Not completed,Completed"
|
|
textline " "
|
|
eventfld.long 0x08 0. " CC ,Command Complete" "Not completed,Completed"
|
|
width 15.
|
|
line.long 0x0C "IRQSTATEN,Interrupt Status Enable Register"
|
|
bitfld.long 0x0C 28. " DMAESEN ,DMA Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 24. " AC12ESEN ,Auto CMD12 Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 22. " DEBESEN ,Data End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 21. " DCESEN ,Data CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 20. " DTOESEN ,Data Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 19. " CIESEN ,Command Index Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 18. " CEBESEN ,Command End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 17. " CCESEN ,Command CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 16. " CTOESEN ,Command Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 8. " CINTSEN ,Card Interrupt Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 7. " CRMSEN ,Card Removal Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 6. " CINSSEN ,Card Insertion Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " BRRSEN ,Buffer Read Ready Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 4. " BWRSEN ,Buffer Write Ready Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 3. " DINTSEN ,DMA Interrupt Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 2. " BGESEN ,Block Gap Event Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 1. " TCSEN ,Transfer Complete Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 0. " CCSEN ,Command Complete Status Enable" "Masked,Enabled"
|
|
line.long 0x10 "IRQSIGEN,Interrupt Signal Enable Register"
|
|
bitfld.long 0x10 28. " DMAEIEN ,DMA Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 24. " AC12EIEN ,Auto CMD12 Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 22. " DEBEIEN ,Data End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 21. " DCEIEN ,Data CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 20. " DTOEIEN ,Data Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 19. " CIEIEN ,Command Index Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 18. " CEBEIEN ,Command End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 17. " CCEIEN ,Command CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 16. " CTOEIEN ,Command Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 8. " CINTIEN ,Card Interrupt Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " CRMIEN ,Card Removal Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 6. " CINSIEN ,Card Insertion Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 5. " BRRIEN ,Buffer Read Ready Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 4. " BWRIEN ,Buffer Write Ready Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " DINTIEN ,DMA Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 2. " BGEIEN ,Block Gap Event Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 1. " TCIEN ,Transfer Complete Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 0. " CCIEN ,Command Complete Interrupt Enable" "Masked,Enabled"
|
|
if (((data.long(ad:0x53FB8000+0x30))&0x1000000)==0x1000000)
|
|
rgroup.long 0x3C++0x3
|
|
line.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
bitfld.long 0x00 7. " CNIBAC12E ,Command Not Issued By Auto CMD12 Error" "No error,Not Issued"
|
|
bitfld.long 0x00 4. " AC12IE ,Auto CMD12 Index Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 3. " AC12CE ,Auto CMD12 CRC Error" "No error,Error"
|
|
bitfld.long 0x00 2. " AC12EBE ,Auto CMD12 End Bit Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 1. " AC12TOE ,Auto CMD12 Timeout Error" "No error,Error"
|
|
bitfld.long 0x00 0. " AC12NE ,Auto CMD12 Not Executed" "Executed,Not executed"
|
|
else
|
|
hgroup.long 0x3C++0x3
|
|
hide.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
endif
|
|
rgroup.long 0x40++0x3
|
|
line.long 0x00 "HOSTCAPBLT,Host Controller Capabilities"
|
|
bitfld.long 0x00 26. " VS18 ,Voltage Support 1.8V" "Not supported,Supported"
|
|
bitfld.long 0x00 25. " VS30 ,Voltage Support 3.0V" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 24. " VS33 ,Voltage Support 3.3V" "Not supported,Supported"
|
|
bitfld.long 0x00 23. " SRS ,Suspend / Resume Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DMAS ,DMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 21. " HSS ,High Speed Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 20. " ADMAS ,ADMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 16.--18. " MBL ,Max Block Length" "512 bytes,1024 bytes,2048 bytes,4096 bytes,?..."
|
|
group.long 0x44++0x3
|
|
line.long 0x00 "WML,Watermark Level Register"
|
|
hexmask.long.byte 0x00 24.--28. 1. " WR_BRST_LEN ,Write Burst Length"
|
|
hexmask.long.byte 0x00 16.--23. 1. " WR_WML ,Write Watermark Level"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--12. 1. " RD_BRST_LEN ,Read Burst Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RD_WML ,Read Watermark Level"
|
|
wgroup.long 0x50++0x3
|
|
line.long 0x00 "FEVT,Force Event Register"
|
|
bitfld.long 0x00 31. " FEVTCINT ,Force Event Card Interrupt" "No effect,Force"
|
|
bitfld.long 0x00 28. " FEVTDMAE ,Force Event DMA Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 24. " FEVTAC12E ,Force Event Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 22. " FEVTDEBE ,Force Event Data End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 21. " FEVTDCE ,Force Event Data CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 20. " FEVTDTOE ,Force Event Data Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 19. " FEVTCIE ,Force Event Command Index Error" "No effect,Force"
|
|
bitfld.long 0x00 18. " FEVTCEBE ,Force Event Command End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 17. " FEVTCCE ,Force Event Command CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 16. " FEVTCTOE ,Force Event Command Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 7. " FEVTCNIBAC12E ,Force Event Command Not Executed By Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 4. " FEVTAC12IE ,Force Event Auto Command 12 Index Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 3. " FEVTAC12EBE ,Force Event Auto Command 12 End Bit Error" "No effect,Force"
|
|
bitfld.long 0x00 2. " FEVTAC12CE ,Force Event Auto Command 12 CRC Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 1. " FEVTAC12TOE ,Force Event Auto Command 12 Time Out Error" "No effect,Force"
|
|
bitfld.long 0x00 0. " FEVTAC12NE ,Force Event Auto Command 12 Not Executed" "No effect,Force"
|
|
rgroup.long 0x54++0x3
|
|
line.long 0x00 "ADMAES,ADMA Error Status Register"
|
|
bitfld.long 0x00 3. " ADMADCE ,ADMA Descriptor Error" "No error,Error"
|
|
bitfld.long 0x00 2. " ADMALME ,ADMA Length Mismatch Error" "No error,Error"
|
|
bitfld.long 0x00 0.--1. " ADMAES ,ADMA Error State" "Stop DMA,Fetch Descriptor,Change Address,Transfer Data"
|
|
group.long 0x58++0x3
|
|
line.long 0x00 "ADSADDR,ADMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " ADS_ADDR[31:0] ,ADMA system address"
|
|
group.long 0xC0++0x03
|
|
line.long 0x00 "VENDOR,Vendor Specific Register"
|
|
bitfld.long 0x00 24.--27. " DBG_SEL[3:0] ,Debug select" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
hexmask.long.byte 0x00 16.--23. 1. " INT_ST_VAL[7:0] ,Internal state value"
|
|
textline " "
|
|
bitfld.long 0x00 1. " VOLT_SEL ,Voltage selection" "Low,High"
|
|
bitfld.long 0x00 0. " EXT_DMA_EN ,External DMA request enable" "Disabled,Enabled"
|
|
rgroup.long 0xfc++0x3
|
|
line.long 0x00 "HCV,Host Controller Version"
|
|
hexmask.long.byte 0x00 8.--15. 1. " VVN[7:0] ,Vendor Version Number"
|
|
hexmask.long.byte 0x00 0.--7. 1. " SVN[7:0] ,Specification Version Number"
|
|
tree.end
|
|
tree "eSDHC 3"
|
|
base ad:0x53FBC000
|
|
width 15.
|
|
group.long 0x00++0xF
|
|
line.long 0x00 "DSADDR,DMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " DS_ADDR[31:2] ,DMA system address"
|
|
line.long 0x04 "BLKATTR,Block Attributes Register"
|
|
hexmask.long.word 0x04 16.--31. 1. " BLKCNT ,Blocks Count For Current Transfer"
|
|
hexmask.long.word 0x04 0.--12. 1. " BLKSZE ,Transfer Block Size"
|
|
line.long 0x08 "CMDARG,Command Argument Register"
|
|
line.long 0x0C "XFERTYP,Transfer Type Register"
|
|
hexmask.long.byte 0x0C 24.--29. 1. " CMDINX ,Command Index"
|
|
bitfld.long 0x0C 22.--23. " CMDTYP ,Command Type" "Normal,Suspend,Resume,Abort"
|
|
textline " "
|
|
bitfld.long 0x0C 21. " DPSEL ,Data Present Select" "No data,Data present"
|
|
bitfld.long 0x0C 20. " CICEN ,Command Index Check Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 19. " CCCEN ,Command CRC Check Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 16.--17. " RSPTYP ,Response Type Select" "No Response,Length 136,Length 48,Length 48 check busy"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " MSBSEL ,Multi / Single Block Select" "Single,Multiple"
|
|
bitfld.long 0x0C 4. " DTDSEL ,Data Transfer Direction Select" "Write,Read"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " AC12EN ,Auto CMD12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 1. " BCEN ,Block Count Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 0. " DMAEN ,DMA Enable" "Disabled,Enabled"
|
|
if (((data.long(ad:0x53FBC000+0x0c))&0x30000)==0x00)
|
|
hgroup.long 0x10++0x03
|
|
hide.long 0x00 "CMDRSP0,Command Response 0"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
elif (((data.long(ad:0x53FBC000+0x0c))&0x30000)==0x10000)
|
|
rgroup.long 0x10++0xF
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R2 response"
|
|
line.long 0x04 "CMDRSP1,Command Response 1"
|
|
hexmask.long 0x04 0.--31. 1. " CMDRSP1 ,R2 response"
|
|
line.long 0x08 "CMDRSP2,Command Response 2"
|
|
hexmask.long 0x08 0.--31. 1. " CMDRSP2 ,R2 response"
|
|
line.long 0x0C "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x0c 0.--23. 1. " CMDRSP3 ,R2[23:0] response"
|
|
elif (((data.long(ad:0x53FBC000+0x0c))&0x30000)==0x20000)
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1/R3/R4/R5/R6 response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
hgroup.long 0x1c++0x03
|
|
hide.long 0x00 "CMDRSP3,Command Response 3"
|
|
else
|
|
rgroup.long 0x10++0x3
|
|
line.long 0x00 "CMDRSP0,Command Response 0"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP0 ,R1b/R5b response"
|
|
hgroup.long 0x14++0x03
|
|
hide.long 0x00 "CMDRSP1,Command Response 1"
|
|
hgroup.long 0x18++0x03
|
|
hide.long 0x00 "CMDRSP2,Command Response 2"
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "CMDRSP3,Command Response 3"
|
|
hexmask.long 0x00 0.--31. 1. " CMDRSP3 ,R1b response"
|
|
endif
|
|
group.long 0x20++0x3
|
|
line.long 0x00 "DATPORT,Buffer Data Port Register"
|
|
rgroup.long 0x24++0x3
|
|
line.long 0x00 "PRSSTAT,Present State Register"
|
|
bitfld.long 0x00 31. " DLSL[7] ,Line 7 Signal Level" "Low,High"
|
|
bitfld.long 0x00 30. " DLSL[6] ,Line 6 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DLSL[5] ,Line 5 Signal Level" "Low,High"
|
|
bitfld.long 0x00 28. " DLSL[4] ,Line 4 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DLSL[3] ,Line 3 Signal Level" "Low,High"
|
|
bitfld.long 0x00 26. " DLSL[2] ,Line 2 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DLSL[1] ,Line 1 Signal Level" "Low,High"
|
|
bitfld.long 0x00 24. " DLSL[0] ,Line 0 Signal Level" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 23. " CLSL ,CMD Line Signal Level" "Pull-down,Pull-up"
|
|
bitfld.long 0x00 19. " WPSPL ,Write Protect Switch Pin Level" "Protected,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " CDPL ,Card Detect Pin Level" "No card,Card present"
|
|
bitfld.long 0x00 16. " CINS ,Card Inserted" "No card/Reset/Power on,Card inserted"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BREN ,Buffer Read Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BWEN ,Buffer Write Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RTA ,Read Transfer Active" "No data,Transferring"
|
|
bitfld.long 0x00 8. " WTA ,Write Transfer Active" "No data,Transferring"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SDOFF ,SD Clock Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 6. " PEROFF ,IPG_PERCLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 5. " HCKOFF ,HCLK Gated Off Internally" "Active,Gated off"
|
|
bitfld.long 0x00 4. " IPGOFF ,IPG_CLK Gated Off Internally" "Active,Gated off"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SDSTB ,SD clock stable" "Not stable,Stable"
|
|
bitfld.long 0x00 2. " DLA ,Data Line Active" "Inactive,Active"
|
|
textline " "
|
|
bitfld.long 0x00 1. " CDIHB ,Command Inhibit (DAT)" "Can issue,Cannot issue"
|
|
bitfld.long 0x00 0. " CIHB ,Command Inhibit (CMD)" "Can issue,Cannot issue"
|
|
group.long 0x28++0x13
|
|
line.long 0x00 "PROCTL,Protocol Control Register"
|
|
bitfld.long 0x00 26. " WECRM ,Wakeup Event Enable On SD Card Removal" "Disabled,Enabled"
|
|
bitfld.long 0x00 25. " WECINS ,Wakeup Event Enable On SD Card Insertion" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " WECINT ,Wakeup Event Enable On Card Interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " IABG ,Interrupt At Block Gap" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " RWCTL ,Read Wait Control" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " CREQ ,Continue Request" "No effect,Restart"
|
|
textline " "
|
|
bitfld.long 0x00 16. " SABGREQ ,Stop At Block Gap Request" "Transfer,Stop"
|
|
bitfld.long 0x00 8.--9. " DMAS ,DMA Select" "No/Simple DMA,ADMA1,ADMA2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " CDSS ,Card Detect Signal Selection" "Level,Test level"
|
|
bitfld.long 0x00 6. " CDTL ,Card Detect Test Level" "No card,Card present"
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " EMODE ,Endian Mode" "Big endian,Half word big endian,Little endian,?..."
|
|
bitfld.long 0x00 3. " D3CD ,DAT3 as Card Detection Pin" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1.--2. " DTW ,Data Transfer Width" "1-bit,4-bit,8-bit,?..."
|
|
bitfld.long 0x00 0. " LCTL ,LED Control" "Off,On"
|
|
line.long 0x04 "SYSCTL,System Control Register"
|
|
bitfld.long 0x04 27. " INITA ,Initialization Active" "No effect,Active"
|
|
textline " "
|
|
bitfld.long 0x04 26. " RSTD ,Software Reset For DAT Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 25. " RSTC ,Software Reset For CMD Line" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 24. " RSTA ,Software Reset For ALL" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 16.--19. " DTOCV ,Data Timeout Counter Value" "SDCLKx2^13,SDCLKx2^14,SDCLKx2^15,SDCLKx2^16,SDCLKx2^17,SDCLKx2^18,SDCLKx2^19,SDCLKx2^20,SDCLKx2^21,SDCLKx2^22,SDCLKx2^23,SDCLKx2^24,SDCLKx2^25,SDCLKx2^26,SDCLKx2^27,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x04 8.--15. 1. " SDCLKFS ,SDCLK Frequency Select"
|
|
textline " "
|
|
bitfld.long 0x04 4.--7. " DVS ,Divisor" "Divisor by 1,Divisor by 2,Divisor by 3,Divisor by 4,Divisor by 5,Divisor by 6,Divisor by 7,Divisor by 8,Divisor by 9,Divisor by 10,Divisor by 11,Divisor by 12,Divisor by 13,Divisor by 14,Divisor by 15,Divisor by 16"
|
|
textline " "
|
|
bitfld.long 0x04 3. " SDCLKEN ,SD clock enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 2. " PEREN ,Peripheral Clock Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 1. " HCKEN ,HCLK Enable" "Internally gated off,No auto gated off"
|
|
textline " "
|
|
bitfld.long 0x04 0. " IPGEN ,IPG Clock Enable" "Internally gated off,No auto gated off"
|
|
line.long 0x08 "IRQSTAT,Interrupt Status Register"
|
|
eventfld.long 0x08 28. " DMAE ,DMA Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 24. " AC12E ,Auto CMD12 Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 22. " DEBE ,Data End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 21. " DCE ,Data CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 20. " DTOE ,Data Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 19. " CIE ,Command Index Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 18. " CEBE ,Command End Bit Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 17. " CCE ,Command CRC Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 16. " CTOE ,Command Timeout Error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x08 8. " CINT ,Card Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 7. " CRM ,Card Removal" "Unstable/Inserted,Removed"
|
|
textline " "
|
|
eventfld.long 0x08 6. " CINS ,Card Insertion" "Unstable/Removed,Inserted"
|
|
textline " "
|
|
eventfld.long 0x08 5. " BRR ,Buffer Read Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 4. " BWR ,Buffer Write Ready" "Not ready,Ready"
|
|
textline " "
|
|
eventfld.long 0x08 3. " DINT ,DMA Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 2. " BGE ,Block Gap Event" "No event,Event occurred"
|
|
textline " "
|
|
eventfld.long 0x08 1. " TC ,Transfer Complete" "Not completed,Completed"
|
|
textline " "
|
|
eventfld.long 0x08 0. " CC ,Command Complete" "Not completed,Completed"
|
|
width 15.
|
|
line.long 0x0C "IRQSTATEN,Interrupt Status Enable Register"
|
|
bitfld.long 0x0C 28. " DMAESEN ,DMA Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 24. " AC12ESEN ,Auto CMD12 Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 22. " DEBESEN ,Data End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 21. " DCESEN ,Data CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 20. " DTOESEN ,Data Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 19. " CIESEN ,Command Index Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 18. " CEBESEN ,Command End Bit Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 17. " CCESEN ,Command CRC Error Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 16. " CTOESEN ,Command Timeout Error Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 8. " CINTSEN ,Card Interrupt Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 7. " CRMSEN ,Card Removal Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 6. " CINSSEN ,Card Insertion Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " BRRSEN ,Buffer Read Ready Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 4. " BWRSEN ,Buffer Write Ready Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 3. " DINTSEN ,DMA Interrupt Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 2. " BGESEN ,Block Gap Event Status Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 1. " TCSEN ,Transfer Complete Status Enable" "Masked,Enabled"
|
|
bitfld.long 0x0C 0. " CCSEN ,Command Complete Status Enable" "Masked,Enabled"
|
|
line.long 0x10 "IRQSIGEN,Interrupt Signal Enable Register"
|
|
bitfld.long 0x10 28. " DMAEIEN ,DMA Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 24. " AC12EIEN ,Auto CMD12 Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 22. " DEBEIEN ,Data End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 21. " DCEIEN ,Data CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 20. " DTOEIEN ,Data Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 19. " CIEIEN ,Command Index Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 18. " CEBEIEN ,Command End Bit Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 17. " CCEIEN ,Command CRC Error Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 16. " CTOEIEN ,Command Timeout Error Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 8. " CINTIEN ,Card Interrupt Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " CRMIEN ,Card Removal Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 6. " CINSIEN ,Card Insertion Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 5. " BRRIEN ,Buffer Read Ready Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 4. " BWRIEN ,Buffer Write Ready Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " DINTIEN ,DMA Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 2. " BGEIEN ,Block Gap Event Interrupt Enable" "Masked,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 1. " TCIEN ,Transfer Complete Interrupt Enable" "Masked,Enabled"
|
|
bitfld.long 0x10 0. " CCIEN ,Command Complete Interrupt Enable" "Masked,Enabled"
|
|
if (((data.long(ad:0x53FBC000+0x30))&0x1000000)==0x1000000)
|
|
rgroup.long 0x3C++0x3
|
|
line.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
bitfld.long 0x00 7. " CNIBAC12E ,Command Not Issued By Auto CMD12 Error" "No error,Not Issued"
|
|
bitfld.long 0x00 4. " AC12IE ,Auto CMD12 Index Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 3. " AC12CE ,Auto CMD12 CRC Error" "No error,Error"
|
|
bitfld.long 0x00 2. " AC12EBE ,Auto CMD12 End Bit Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 1. " AC12TOE ,Auto CMD12 Timeout Error" "No error,Error"
|
|
bitfld.long 0x00 0. " AC12NE ,Auto CMD12 Not Executed" "Executed,Not executed"
|
|
else
|
|
hgroup.long 0x3C++0x3
|
|
hide.long 0x00 "AUTOC12ERR,Auto CMD12 Error Status Register"
|
|
endif
|
|
rgroup.long 0x40++0x3
|
|
line.long 0x00 "HOSTCAPBLT,Host Controller Capabilities"
|
|
bitfld.long 0x00 26. " VS18 ,Voltage Support 1.8V" "Not supported,Supported"
|
|
bitfld.long 0x00 25. " VS30 ,Voltage Support 3.0V" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 24. " VS33 ,Voltage Support 3.3V" "Not supported,Supported"
|
|
bitfld.long 0x00 23. " SRS ,Suspend / Resume Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DMAS ,DMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 21. " HSS ,High Speed Support" "Not supported,Supported"
|
|
textline " "
|
|
bitfld.long 0x00 20. " ADMAS ,ADMA Support" "Not supported,Supported"
|
|
bitfld.long 0x00 16.--18. " MBL ,Max Block Length" "512 bytes,1024 bytes,2048 bytes,4096 bytes,?..."
|
|
group.long 0x44++0x3
|
|
line.long 0x00 "WML,Watermark Level Register"
|
|
hexmask.long.byte 0x00 24.--28. 1. " WR_BRST_LEN ,Write Burst Length"
|
|
hexmask.long.byte 0x00 16.--23. 1. " WR_WML ,Write Watermark Level"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--12. 1. " RD_BRST_LEN ,Read Burst Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RD_WML ,Read Watermark Level"
|
|
wgroup.long 0x50++0x3
|
|
line.long 0x00 "FEVT,Force Event Register"
|
|
bitfld.long 0x00 31. " FEVTCINT ,Force Event Card Interrupt" "No effect,Force"
|
|
bitfld.long 0x00 28. " FEVTDMAE ,Force Event DMA Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 24. " FEVTAC12E ,Force Event Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 22. " FEVTDEBE ,Force Event Data End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 21. " FEVTDCE ,Force Event Data CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 20. " FEVTDTOE ,Force Event Data Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 19. " FEVTCIE ,Force Event Command Index Error" "No effect,Force"
|
|
bitfld.long 0x00 18. " FEVTCEBE ,Force Event Command End Bit Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 17. " FEVTCCE ,Force Event Command CRC Error" "No effect,Force"
|
|
bitfld.long 0x00 16. " FEVTCTOE ,Force Event Command Time Out Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 7. " FEVTCNIBAC12E ,Force Event Command Not Executed By Auto Command 12 Error" "No effect,Force"
|
|
bitfld.long 0x00 4. " FEVTAC12IE ,Force Event Auto Command 12 Index Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 3. " FEVTAC12EBE ,Force Event Auto Command 12 End Bit Error" "No effect,Force"
|
|
bitfld.long 0x00 2. " FEVTAC12CE ,Force Event Auto Command 12 CRC Error" "No effect,Force"
|
|
textline " "
|
|
bitfld.long 0x00 1. " FEVTAC12TOE ,Force Event Auto Command 12 Time Out Error" "No effect,Force"
|
|
bitfld.long 0x00 0. " FEVTAC12NE ,Force Event Auto Command 12 Not Executed" "No effect,Force"
|
|
rgroup.long 0x54++0x3
|
|
line.long 0x00 "ADMAES,ADMA Error Status Register"
|
|
bitfld.long 0x00 3. " ADMADCE ,ADMA Descriptor Error" "No error,Error"
|
|
bitfld.long 0x00 2. " ADMALME ,ADMA Length Mismatch Error" "No error,Error"
|
|
bitfld.long 0x00 0.--1. " ADMAES ,ADMA Error State" "Stop DMA,Fetch Descriptor,Change Address,Transfer Data"
|
|
group.long 0x58++0x3
|
|
line.long 0x00 "ADSADDR,ADMA System Address Register"
|
|
hexmask.long 0x00 2.--31. 1. " ADS_ADDR[31:0] ,ADMA system address"
|
|
group.long 0xC0++0x03
|
|
line.long 0x00 "VENDOR,Vendor Specific Register"
|
|
bitfld.long 0x00 24.--27. " DBG_SEL[3:0] ,Debug select" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
hexmask.long.byte 0x00 16.--23. 1. " INT_ST_VAL[7:0] ,Internal state value"
|
|
textline " "
|
|
bitfld.long 0x00 1. " VOLT_SEL ,Voltage selection" "Low,High"
|
|
bitfld.long 0x00 0. " EXT_DMA_EN ,External DMA request enable" "Disabled,Enabled"
|
|
rgroup.long 0xfc++0x3
|
|
line.long 0x00 "HCV,Host Controller Version"
|
|
hexmask.long.byte 0x00 8.--15. 1. " VVN[7:0] ,Vendor Version Number"
|
|
hexmask.long.byte 0x00 0.--7. 1. " SVN[7:0] ,Specification Version Number"
|
|
tree.end
|
|
tree.end
|
|
tree.open "FEC (Fast Ethernet Controller)"
|
|
base ad:0x50038000
|
|
width 8.
|
|
tree "Control/Status Registers"
|
|
group.long 0x04++0x7
|
|
line.long 0x00 "EIR,Ethernet Interrupt Event Register"
|
|
eventfld.long 0x00 31. " HBERR ,Heartbeat error" "No error,Error"
|
|
eventfld.long 0x00 30. " BABR ,Babbling receive error" "No error,Error"
|
|
eventfld.long 0x00 29. " BABT ,Babbling transmit error" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x00 28. " GRA ,Graceful stop complete" "Not completed,Completed"
|
|
eventfld.long 0x00 27. " TXF ,Transmit frame interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 26. " TXB ,Transmit buffer interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 25. " RXF ,Receive frame interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 24. " RXB ,Receive buffer interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 23. " MII ,MII interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 22. " EBERR ,Ethernet bus error" "No error,Error"
|
|
eventfld.long 0x00 21. " LC ,Late collision" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " RL ,Collision retry limit" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " UN ,Transmit FIFO underrun" "Not empty,Empty"
|
|
line.long 0x04 "EIMR,Interrupt Mask Register"
|
|
bitfld.long 0x04 31. " HBERR ,Heartbeat error" "Masked,Not masked"
|
|
bitfld.long 0x04 30. " BABR ,Babbling receive error" "Masked,Not masked"
|
|
bitfld.long 0x04 29. " BABT ,Babbling receive error" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x04 28. " GRA ,Graceful stop complete" "Masked,Not masked"
|
|
bitfld.long 0x04 27. " TXF ,Transmit frame interrupt" "Masked,Not masked"
|
|
bitfld.long 0x04 26. " TXB ,Transmit buffer interrupt" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x04 25. " RXF ,Receive frame interrupt" "Masked,Not masked"
|
|
bitfld.long 0x04 24. " RXB ,Receive buffer interrupt" "Masked,Not masked"
|
|
bitfld.long 0x04 23. " MII ,MII interrupt" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x04 22. " EBERR ,Ethernet bus error" "Masked,Not masked"
|
|
bitfld.long 0x04 21. " LC ,Late collision" "Masked,Not masked"
|
|
bitfld.long 0x04 20. " RL ,Collision retry limit" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x04 19. " UN ,Transmit FIFO underrun" "Masked,Not masked"
|
|
width 14.
|
|
group.long 0x10++0x07
|
|
line.long 0x00 "RDAR,Receive Descriptor Active Register"
|
|
bitfld.long 0x00 24. " R_DES_ACTIVE ,Indicates that the receive descriptor ring has been updated" "Not received,Recived"
|
|
line.long 0x04 "TDAR,Transmit Descriptor Active Register"
|
|
bitfld.long 0x04 24. " X_DES_ACTIVE ,Indicates that the transmit descriptor ring has been updated" "Not transmitted,Transmitted"
|
|
width 12.
|
|
group.long 0x24++0x03
|
|
line.long 0x00 "ECR,Ethernet Control Register"
|
|
bitfld.long 0x00 1. " ETHER_EN ,Ethernet enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " RESET ,Reset" "No reset,Reset"
|
|
group.long 0x40++0x07
|
|
line.long 0x00 "MMFR,MII Management Frame Register"
|
|
bitfld.long 0x00 30.--31. " ST ,Start of frame delimiter" "0,1,2,3"
|
|
bitfld.long 0x00 28.--29. " OP ,Operation code" "Write,Write for MII frame,Read for MII frame,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23.--27. " PA ,PHY address" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
bitfld.long 0x00 18.--22. " RA ,Register address" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
bitfld.long 0x00 16.--17. " TA ,Turn around" "0,1,2,3"
|
|
hexmask.long.word 0x00 0.--15. 1. " DATA ,Management frame data"
|
|
line.long 0x04 "MSCR,MII Speed Control Register"
|
|
bitfld.long 0x04 7. " DIS_PREAMBLE ,Causes preamble not to be prepended to the MII management frame" "Low,High"
|
|
bitfld.long 0x04 1.--6. " MII_SPEED ,Controls the frequency of the MII management interface clock" "Turned off,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
group.long 0x64++0x03
|
|
line.long 0x00 "MIBC,MIB Control Register"
|
|
bitfld.long 0x00 31. " MIB_DISABLE ,A read/write control bit" "Not halted,Halted"
|
|
bitfld.long 0x00 30. " MIB_IDLE ,MIB counters update" "Updated,Not updated"
|
|
group.long 0x84++0x03
|
|
line.long 0x00 "RCR,Receive Control Register"
|
|
hexmask.long.word 0x00 16.--26. 1. " MAX_FL ,Maximum frame length"
|
|
bitfld.long 0x00 5. " FCE ,Flow control enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " BC_REJ ,Broadcast frame reject" "Not rejected,Rejected"
|
|
bitfld.long 0x00 3. " PROM ,Promiscuous mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " MII_MODE ,Media independent interface mode" "7-wire,MII"
|
|
bitfld.long 0x00 1. " DRT ,Disable receive on transmit" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 0. " LOOP ,Internal loopback" "Not looped,Looped"
|
|
group.long 0xC4++0x03
|
|
line.long 0x00 "TCR,Transmit Control Register"
|
|
bitfld.long 0x00 4. " RFC_PAUSE ,Receive frame control pause" "Not received,Recived"
|
|
bitfld.long 0x00 3. " TFC_PAUSE ,Transmit frame control pause" "Not transmitted,Transmitted"
|
|
textline " "
|
|
bitfld.long 0x00 2. " FDEN ,Full duplex enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " HBC ,Heartbeat contro" "Not checked,Checked"
|
|
textline " "
|
|
bitfld.long 0x00 0. " GTS ,Graceful transmit stop" "Not stopped,Stopped"
|
|
group.long 0xE4++0x7
|
|
line.long 0x00 "PALR,Physical Address Low Register"
|
|
hexmask.long.byte 0x00 24.--31. 1. " PADDR1_0 ,Byte 0 of the 6 byte destination address"
|
|
hexmask.long.byte 0x00 16.--23. 1. " PADDR1_1 ,Byte 1 of the 6 byte destination address"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " PADDR1_2 ,Byte 2 of the 6 byte destination address"
|
|
hexmask.long.byte 0x00 0.--7. 1. " PADDR1_3 ,Byte 3 of the 6 byte destination address"
|
|
line.long 0x04 "PAUR,Physical Address High Register"
|
|
hexmask.long.byte 0x04 24.--31. 1. " PADDR2_4 ,Byte 4 of the 6 byte destination address"
|
|
hexmask.long.byte 0x04 16.--23. 1. " PADDR2_5 ,Byte 5 of the 6 byte destination address"
|
|
textline " "
|
|
hexmask.long.word 0x04 0.--15. 1. " TYPE ,Type field in PAUSE frames"
|
|
rgroup.long 0xEC++0x3
|
|
line.long 0x00 "OPDR,Opcode/Pause Duration Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " OPCODE ,Opcode field used in PAUSE frames"
|
|
hexmask.long.word 0x00 0.--15. 1. " PAUSE_DUR ,Pause Duration field used in PAUSE frames"
|
|
width 18.
|
|
group.long 0x118++0xF
|
|
line.long 0x00 "IAUR,Descriptor Individual Address Upper Register"
|
|
line.long 0x04 "IALR,Descriptor Individual Address Lower Register"
|
|
line.long 0x08 "GAUR,Descriptor Group Address Upper Register"
|
|
line.long 0x0C "GALR,Descriptor Group Address Lower Register"
|
|
group.long 0x144++0x3
|
|
line.long 0x00 "TFWR,Transmit fifo watermark Register"
|
|
bitfld.long 0x00 0.--1. " X_WMRK ,Number of bytes written to transmit FIFO before transmission of a frame begins" "64 bytes,64 bytes,128 bytes,192 bytes"
|
|
rgroup.long 0x14c++0x03
|
|
line.long 0x00 "FRBR,FIFO Receive Bound Register"
|
|
hexmask.long.word 0x00 2.--9. 0x04 " R_BOUND ,Highest valid FIFO RAM address"
|
|
group.long 0x150++0x03
|
|
line.long 0x00 "FRSR,FIFO Receive Start Register"
|
|
hexmask.long.word 0x00 2.--9. 0x04 " R_FSTART ,Address of first receive FIFO location"
|
|
group.long 0x180++0xb
|
|
line.long 0x00 "ERDSR,Receive Buffer Descriptor Ring Start Register"
|
|
hexmask.long 0x00 2.--31. 0x4 " R_DES_START ,Pointer to start of receive buffer descriptor queue"
|
|
line.long 0x04 "ETDSR,Transmit Buffer Descriptor Ring Start Register"
|
|
hexmask.long 0x04 2.--31. 0x4 " X_DES_START ,Pointer to start of transmit buffer descriptor queue"
|
|
line.long 0x08 "EMRBR,Maximum Receive Buffer Size Register"
|
|
hexmask.long.byte 0x08 4.--10. 1. " R_BUF_SIZE ,Receive buffer size in bytes"
|
|
tree.end
|
|
tree "MIB Block Counters"
|
|
width 20.
|
|
group.long 0x200++0x77
|
|
line.long 0x00 "RMON_T_DROP,Count of frames not counted correctly"
|
|
line.long 0x04 "RMON_T_PACKETS,RMON Tx packet count"
|
|
line.long 0x08 "RMON_T_BC_PKT,RMON Tx Broadcast Packets"
|
|
line.long 0x0c "RMON_T_MC_PKT,RMON Tx Multicast Packets"
|
|
line.long 0x10 "RMON_T_CRC_ALIGN,RMON Tx Packets w CRC/Align error"
|
|
line.long 0x14 "RMON_T_UNDERSIZE,RMON Tx Packets < 64 bytes"
|
|
line.long 0x18 "RMON_T_OVERSIZE,RMON Tx Packets > MAX_FL bytes"
|
|
line.long 0x1c "RMON_T_FRAG,RMON Tx Packets < 64 bytes"
|
|
line.long 0x20 "RMON_T_JAB,RMON Tx Packets > MAX_FL bytes"
|
|
line.long 0x24 "RMON_T_COL,RMON Tx collision count"
|
|
line.long 0x28 "RMON_T_P64,RMON Tx 64 byte packets"
|
|
line.long 0x2c "RMON_T_P65TO127,RMON Tx 65 to 127 byte packets"
|
|
line.long 0x30 "RMON_T_P128TO255,RMON Tx 128 to 255 byte packets"
|
|
line.long 0x34 "RMON_T_P256TO511,RMON Tx 256 to 511 byte packets"
|
|
line.long 0x38 "RMON_T_P512TO1023,RMON Tx 512 to 1023 byte packets"
|
|
line.long 0x3c "RMON_T_P1024TO2047,RMON Tx 1024 to 2047 byte packets"
|
|
line.long 0x40 "RMON_T_P_GTE2048,RMON Tx packets w > 2048 bytes"
|
|
line.long 0x44 "RMON_T_OCTETS,RMON Tx Octets"
|
|
line.long 0x48 "IEEE_T_DROP,Count of frames not counted correctly"
|
|
line.long 0x4c "IEEE_T_FRAME_OK,Frames Transmitted OK"
|
|
line.long 0x50 "IEEE_T_1COL,Frames Transmitted with Single Collision"
|
|
line.long 0x54 "IEEE_T_MCOL,Frames Transmitted with Multiple Collisions"
|
|
line.long 0x58 "IEEE_T_DEF,Frames Transmitted after Deferral Delay"
|
|
line.long 0x5c "IEEE_T_LCOL,Frames Transmitted with Late Collision"
|
|
line.long 0x60 "IEEE_T_EXCOL,Frames Transmitted with Excessive Collisions"
|
|
line.long 0x64 "IEEE_T_MACERR,Frames Transmitted with Tx FIFO Underrun"
|
|
line.long 0x68 "IEEE_T_CSERR,Frames Transmitted with Carrier Sense Error"
|
|
line.long 0x6c "IEEE_T_SQE,Frames Transmitted with SQE Error"
|
|
line.long 0x70 "IEEE_T_FDXFC,Flow Control Pause frames transmitted"
|
|
line.long 0x74 "IEEE_T_OCTETS_OK,Octet count for Frames Transmitted w/o Error"
|
|
group.long 0x284++0x5f
|
|
line.long 0x00 "RMON_R_PACKETS,RMON Rx packet count"
|
|
line.long 0x04 "RMON_R_BC_PKT,RMON Rx Broadcast Packets"
|
|
line.long 0x08 "RMON_R_MC_PKT,RMON Rx Multicast Packets"
|
|
line.long 0x0c "RMON_R_CRC_ALIGN,RMON Rx Packets w CRC/Align error"
|
|
line.long 0x10 "RMON_R_UNDERSIZE,RMON Rx Packets < 64 bytes"
|
|
line.long 0x14 "RMON_R_OVERSIZE,RMON Rx Packets > MAX_FL bytes"
|
|
line.long 0x18 "RMON_R_FRAG,RMON Rx Packets < 64 bytes"
|
|
line.long 0x1c "RMON_R_JAB,RMON Rx Packets > MAX_FL bytes"
|
|
line.long 0x20 "RMON_R_RESVD_0,RMON_R_RESVD_0"
|
|
line.long 0x24 "RMON_R_P64,RMON Rx 64 byte packets"
|
|
line.long 0x28 "RMON_R_P65TO127,RMON Rx 65 to 127 byte packets"
|
|
line.long 0x2c "RMON_R_P128TO255,RMON Rx 128 to 255 byte packets"
|
|
line.long 0x30 "RMON_R_P256TO511,RMON Rx 256 to 511 byte packets"
|
|
line.long 0x34 "RMON_R_P512TO1023,RMON Rx 512 to 1023 byte packets"
|
|
line.long 0x38 "RMON_R_P1024TO2047,RMON Rx 1024 to 2047 byte packets"
|
|
line.long 0x3c "RMON_R_P_GTE2048,RMON Rx packets w > 2048 bytes"
|
|
line.long 0x40 "RMON_R_OCTETS,RMON Rx Octets"
|
|
line.long 0x44 "IEEE_R_DROP,Count of frames not counted correctly"
|
|
line.long 0x48 "IEEE_R_FRAME_OK,Frames Received OK"
|
|
line.long 0x4c "IEEE_R_CRC,Frames Received with CRC Error"
|
|
line.long 0x50 "IEEE_R_ALIGN,Frames Received with Alignment Error"
|
|
line.long 0x54 "IEEE_R_MACERR,Receive Fifo Overflow count"
|
|
line.long 0x58 "IEEE_R_FDXFC,Flow Control Pause frames received"
|
|
line.long 0x5c "IEEE_R_OCTETS_OK,Octet count for Frames Rcvd w/o Error"
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree.open "GPIO (General Purpose Input/Output)"
|
|
tree "GPIO 1"
|
|
base ad:0x53fcc000
|
|
width 0x7
|
|
group.long 0x00++0x7
|
|
line.long 0x00 "DR,GPIO Data Register"
|
|
bitfld.long 0x00 31. " DR31 ,Data bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " DR30 ,Data bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " DR29 ,Data bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " DR28 ,Data bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " DR27 ,Data bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " DR26 ,Data bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DR25 ,Data bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " DR24 ,Data bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " DR23 ,Data bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DR22 ,Data bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " DR21 ,Data bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " DR20 ,Data bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " DR19 ,Data bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " DR18 ,Data bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " DR17 ,Data bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " DR16 ,Data bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " DR15 ,Data bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " DR14 ,Data bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " DR13 ,Data bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " DR12 ,Data bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " DR11 ,Data bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " DR10 ,Data bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " DR9 ,Data bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " DR8 ,Data bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " DR7 ,Data bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " DR6 ,Data bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " DR5 ,Data bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " DR4 ,Data bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " DR3 ,Data bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " DR2 ,Data bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " DR1 ,Data bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " DR0 ,Data bit 0" "Low,High"
|
|
line.long 0x04 "GDIR,GPIO Direction Register"
|
|
bitfld.long 0x04 31. " GDIR31 ,GPIO Direction 31 bit" "Input,Output"
|
|
bitfld.long 0x04 30. " GDIR30 ,GPIO Direction 30 bit" "Input,Output"
|
|
bitfld.long 0x04 29. " GDIR29 ,GPIO Direction 29 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 28. " GDIR28 ,GPIO Direction 28 bit" "Input,Output"
|
|
bitfld.long 0x04 27. " GDIR27 ,GPIO Direction 27 bit" "Input,Output"
|
|
bitfld.long 0x04 26. " GDIR26 ,GPIO Direction 26 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 25. " GDIR25 ,GPIO Direction 25 bit" "Input,Output"
|
|
bitfld.long 0x04 24. " GDIR24 ,GPIO Direction 24 bit" "Input,Output"
|
|
bitfld.long 0x04 23. " GDIR23 ,GPIO Direction 23 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 22. " GDIR22 ,GPIO Direction 22 bit" "Input,Output"
|
|
bitfld.long 0x04 21. " GDIR21 ,GPIO Direction 21 bit" "Input,Output"
|
|
bitfld.long 0x04 20. " GDIR20 ,GPIO Direction 20 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 19. " GDIR19 ,GPIO Direction 19 bit" "Input,Output"
|
|
bitfld.long 0x04 18. " GDIR18 ,GPIO Direction 18 bit" "Input,Output"
|
|
bitfld.long 0x04 17. " GDIR17 ,GPIO Direction 17 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 16. " GDIR16 ,GPIO Direction 16 bit" "Input,Output"
|
|
bitfld.long 0x04 15. " GDIR15 ,GPIO Direction 15 bit" "Input,Output"
|
|
bitfld.long 0x04 14. " GDIR14 ,GPIO Direction 14 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 13. " GDIR13 ,GPIO Direction 13 bit" "Input,Output"
|
|
bitfld.long 0x04 12. " GDIR12 ,GPIO Direction 12 bit" "Input,Output"
|
|
bitfld.long 0x04 11. " GDIR11 ,GPIO Direction 11 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 10. " GDIR10 ,GPIO Direction 10 bit" "Input,Output"
|
|
bitfld.long 0x04 9. " GDIR9 ,GPIO Direction 9 bit" "Input,Output"
|
|
bitfld.long 0x04 8. " GDIR8 ,GPIO Direction 8 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 7. " GDIR7 ,GPIO Direction 7 bit" "Input,Output"
|
|
bitfld.long 0x04 6. " GDIR6 ,GPIO Direction 6 bit" "Input,Output"
|
|
bitfld.long 0x04 5. " GDIR5 ,GPIO Direction 5 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 4. " GDIR4 ,GPIO Direction 4 bit" "Input,Output"
|
|
bitfld.long 0x04 3. " GDIR3 ,GPIO Direction 3 bit" "Input,Output"
|
|
bitfld.long 0x04 2. " GDIR2 ,GPIO Direction 2 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 1. " GDIR1 ,GPIO Direction 1 bit" "Input,Output"
|
|
bitfld.long 0x04 0. " GDIR0 ,GPIO Direction 0 bit" "Input,Output"
|
|
rgroup.long 0x08++0x3
|
|
line.long 0x00 "PSR,GPIO Pad Status Register"
|
|
bitfld.long 0x00 31. " PSR31 ,GPIO Pad Status bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " PSR30 ,GPIO Pad Status bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " PSR29 ,GPIO Pad Status bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " PSR28 ,GPIO Pad Status bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " PSR27 ,GPIO Pad Status bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " PSR26 ,GPIO Pad Status bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " PSR25 ,GPIO Pad Status bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " PSR24 ,GPIO Pad Status bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " PSR23 ,GPIO Pad Status bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " PSR22 ,GPIO Pad Status bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " PSR21 ,GPIO Pad Status bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " PSR20 ,GPIO Pad Status bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " PSR19 ,GPIO Pad Status bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " PSR18 ,GPIO Pad Status bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " PSR17 ,GPIO Pad Status bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PSR16 ,GPIO Pad Status bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " PSR15 ,GPIO Pad Status bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " PSR14 ,GPIO Pad Status bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " PSR13 ,GPIO Pad Status bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " PSR12 ,GPIO Pad Status bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " PSR11 ,GPIO Pad Status bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " PSR10 ,GPIO Pad Status bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " PSR9 ,GPIO Pad Status bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " PSR8 ,GPIO Pad Status bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " PSR7 ,GPIO Pad Status bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " PSR6 ,GPIO Pad Status bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " PSR5 ,GPIO Pad Status bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " PSR4 ,GPIO Pad Status bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " PSR3 ,GPIO Pad Status bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " PSR2 ,GPIO Pad Status bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " PSR1 ,GPIO Pad Status bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " PSR0 ,GPIO Pad Status bit 0" "Low,High"
|
|
tree "GPIO Interrupt Registers"
|
|
textline " "
|
|
group.long 0x0c++0xF
|
|
line.long 0x00 "ICR1,GPIO Interrupt Configuration Register 1"
|
|
bitfld.long 0x00 30.--31. " ICR1_15 ,Interrupt 15 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 28.--29. " ICR1_14 ,Interrupt 14 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 26.--27. " ICR1_13 ,Interrupt 13 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 24.--25. " ICR1_12 ,Interrupt 12 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " ICR1_11 ,Interrupt 11 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 20.--21. " ICR1_10 ,Interrupt 10 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " ICR1_9 ,Interrupt 9 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 16.--17. " ICR1_8 ,Interrupt 8 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " ICR1_7 ,Interrupt 7 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 12.--13. " ICR1_6 ,Interrupt 6 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " ICR1_5 ,Interrupt 5 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 8.--9. " ICR1_4 ,Interrupt 4 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " ICR1_3 ,Interrupt 3 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 4.--5. " ICR1_2 ,Interrupt 2 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " ICR1_1 ,Interrupt 1 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 0.--1. " ICR1_0 ,Interrupt 0 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x04 "ICR2,GPIO Interrupt Configuration Register 2"
|
|
bitfld.long 0x04 30.--31. " ICR2_31 ,Interrupt 31 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 28.--29. " ICR2_30 ,Interrupt 30 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 26.--27. " ICR2_29 ,Interrupt 29 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 24.--25. " ICR2_28 ,Interrupt 28 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 22.--23. " ICR2_27 ,Interrupt 27 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 20.--21. " ICR2_26 ,Interrupt 26 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " ICR2_25 ,Interrupt 25 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 16.--17. " ICR2_24 ,Interrupt 24 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 14.--15. " ICR2_23 ,Interrupt 23 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 12.--13. " ICR2_22 ,Interrupt 22 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 10.--11. " ICR2_21 ,Interrupt 21 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 8.--9. " ICR2_20 ,Interrupt 20 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 6.--7. " ICR2_19 ,Interrupt 19 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 4.--5. " ICR2_18 ,Interrupt 18 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 2.--3. " ICR2_17 ,Interrupt 17 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 0.--1. " ICR2_16 ,Interrupt 16 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x08 "IMR,GPIO Interrupt Mask Register"
|
|
bitfld.long 0x08 31. " IMR31 ,Interrupt 31 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 30. " IMR30 ,Interrupt 30 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 29. " IMR29 ,Interrupt 29 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 28. " IMR28 ,Interrupt 28 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 27. " IMR27 ,Interrupt 27 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 26. " IMR26 ,Interrupt 26 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 25. " IMR25 ,Interrupt 25 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " IMR24 ,Interrupt 24 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 23. " IMR23 ,Interrupt 23 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 22. " IMR22 ,Interrupt 22 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 21. " IMR21 ,Interrupt 21 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 20. " IMR20 ,Interrupt 20 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 19. " IMR19 ,Interrupt 19 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 18. " IMR18 ,Interrupt 18 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 17. " IMR17 ,Interrupt 17 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 16. " IMR16 ,Interrupt 16 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 15. " IMR15 ,Interrupt 15 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 14. " IMR14 ,Interrupt 14 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 13. " IMR13 ,Interrupt 13 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 12. " IMR12 ,Interrupt 12 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 11. " IMR11 ,Interrupt 11 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 10. " IMR10 ,Interrupt 10 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 9. " IMR9 ,Interrupt 9 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " IMR8 ,Interrupt 8 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " IMR7 ,Interrupt 7 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " IMR6 ,Interrupt 6 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 5. " IMR5 ,Interrupt 5 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 4. " IMR4 ,Interrupt 4 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 3. " IMR3 ,Interrupt 3 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " IMR2 ,Interrupt 2 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " IMR1 ,Interrupt 1 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " IMR0 ,Interrupt 0 Mask bit" "Disabled,Enabled"
|
|
line.long 0x0c "ISR,GPIO Interrupt Status Register"
|
|
eventfld.long 0x0c 31. " ISR31 ,Interrupt 31 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 30. " ISR30 ,Interrupt 30 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 29. " ISR29 ,Interrupt 29 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 28. " ISR28 ,Interrupt 28 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 27. " ISR27 ,Interrupt 27 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 26. " ISR26 ,Interrupt 26 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 25. " ISR25 ,Interrupt 25 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 24. " ISR24 ,Interrupt 24 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 23. " ISR23 ,Interrupt 23 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 22. " ISR22 ,Interrupt 22 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 21. " ISR21 ,Interrupt 21 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 20. " ISR20 ,Interrupt 20 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 19. " ISR19 ,Interrupt 19 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 18. " ISR18 ,Interrupt 18 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 17. " ISR17 ,Interrupt 17 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 16. " ISR16 ,Interrupt 16 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 15. " ISR15 ,Interrupt 15 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 14. " ISR14 ,Interrupt 14 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 13. " ISR13 ,Interrupt 13 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 12. " ISR12 ,Interrupt 12 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 11. " ISR11 ,Interrupt 11 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 10. " ISR10 ,Interrupt 10 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 9. " ISR9 ,Interrupt 9 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 8. " ISR8 ,Interrupt 8 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 7. " ISR7 ,Interrupt 7 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 6. " ISR6 ,Interrupt 6 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 5. " ISR5 ,Interrupt 5 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 4. " ISR4 ,Interrupt 4 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 3. " ISR3 ,Interrupt 3 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 2. " ISR2 ,Interrupt 2 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 1. " ISR1 ,Interrupt 1 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 0. " ISR0 ,Interrupt 0 Status bit" "No interrupt,Interrupt"
|
|
tree.end
|
|
width 0xB
|
|
group.long 0x1c++0x3
|
|
line.long 0x0 "EDGE_SEL,GPIO Edge Select Register"
|
|
bitfld.long 0x0 31. " EDGE_SEL31 ,Edge Selection 31" "ICR_2_31,Any edge"
|
|
bitfld.long 0x0 30. " EDGE_SEL30 ,Edge Selection 30" "ICR_2_30,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 29. " EDGE_SEL29 ,Edge Selection 29" "ICR_2_29,Any edge"
|
|
bitfld.long 0x0 28. " EDGE_SEL28 ,Edge Selection 28" "ICR_2_28,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 27. " EDGE_SEL27 ,Edge Selection 27" "ICR_2_27,Any edge"
|
|
bitfld.long 0x0 26. " EDGE_SEL26 ,Edge Selection 26" "ICR_2_26,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 25. " EDGE_SEL25 ,Edge Selection 25" "ICR_2_25,Any edge"
|
|
bitfld.long 0x0 24. " EDGE_SEL24 ,Edge Selection 24" "ICR_2_24,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 23. " EDGE_SEL23 ,Edge Selection 23" "ICR_2_23,Any edge"
|
|
bitfld.long 0x0 22. " EDGE_SEL22 ,Edge Selection 22" "ICR_2_22,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 21. " EDGE_SEL21 ,Edge Selection 21" "ICR_2_21,Any edge"
|
|
bitfld.long 0x0 20. " EDGE_SEL20 ,Edge Selection 20" "ICR_2_20,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 19. " EDGE_SEL19 ,Edge Selection 19" "ICR_2_19,Any edge"
|
|
bitfld.long 0x0 18. " EDGE_SEL18 ,Edge Selection 18" "ICR_2_18,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 17. " EDGE_SEL17 ,Edge Selection 17" "ICR_2_17,Any edge"
|
|
bitfld.long 0x0 16. " EDGE_SEL16 ,Edge Selection 16" "ICR_2_16,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 15. " EDGE_SEL15 ,Edge Selection 15" "ICR_1_15,Any edge"
|
|
bitfld.long 0x0 14. " EDGE_SEL14 ,Edge Selection 14" "ICR_1_14,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 13. " EDGE_SEL13 ,Edge Selection 13" "ICR_1_13,Any edge"
|
|
bitfld.long 0x0 12. " EDGE_SEL12 ,Edge Selection 12" "ICR_1_12,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 11. " EDGE_SEL11 ,Edge Selection 11" "ICR_1_11,Any edge"
|
|
bitfld.long 0x0 10. " EDGE_SEL10 ,Edge Selection 10" "ICR_1_10,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 9. " EDGE_SEL9 ,Edge Selection 9" "ICR_1_9,Any edge"
|
|
bitfld.long 0x0 8. " EDGE_SEL8 ,Edge Selection 8" "ICR_1_8,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 7. " EDGE_SEL7 ,Edge Selection 7" "ICR_1_7,Any edge"
|
|
bitfld.long 0x0 6. " EDGE_SEL6 ,Edge Selection 6" "ICR_1_6,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 5. " EDGE_SEL5 ,Edge Selection 5" "ICR_1_5,Any edge"
|
|
bitfld.long 0x0 4. " EDGE_SEL4 ,Edge Selection 4" "ICR_1_4,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 3. " EDGE_SEL3 ,Edge Selection 3" "ICR_1_3,Any edge"
|
|
bitfld.long 0x0 2. " EDGE_SEL2 ,Edge Selection 2" "ICR_1_2,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 1. " EDGE_SEL1 ,Edge Selection 1" "ICR_1_1,Any edge"
|
|
bitfld.long 0x0 0. " EDGE_SEL0 ,Edge Selection 0" "ICR_1_0,Any edge"
|
|
width 0xb
|
|
tree.end
|
|
tree "GPIO 2"
|
|
base ad:0x53fd0000
|
|
width 0x7
|
|
group.long 0x00++0x7
|
|
line.long 0x00 "DR,GPIO Data Register"
|
|
bitfld.long 0x00 31. " DR31 ,Data bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " DR30 ,Data bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " DR29 ,Data bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " DR28 ,Data bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " DR27 ,Data bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " DR26 ,Data bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DR25 ,Data bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " DR24 ,Data bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " DR23 ,Data bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DR22 ,Data bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " DR21 ,Data bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " DR20 ,Data bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " DR19 ,Data bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " DR18 ,Data bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " DR17 ,Data bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " DR16 ,Data bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " DR15 ,Data bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " DR14 ,Data bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " DR13 ,Data bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " DR12 ,Data bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " DR11 ,Data bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " DR10 ,Data bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " DR9 ,Data bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " DR8 ,Data bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " DR7 ,Data bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " DR6 ,Data bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " DR5 ,Data bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " DR4 ,Data bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " DR3 ,Data bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " DR2 ,Data bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " DR1 ,Data bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " DR0 ,Data bit 0" "Low,High"
|
|
line.long 0x04 "GDIR,GPIO Direction Register"
|
|
bitfld.long 0x04 31. " GDIR31 ,GPIO Direction 31 bit" "Input,Output"
|
|
bitfld.long 0x04 30. " GDIR30 ,GPIO Direction 30 bit" "Input,Output"
|
|
bitfld.long 0x04 29. " GDIR29 ,GPIO Direction 29 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 28. " GDIR28 ,GPIO Direction 28 bit" "Input,Output"
|
|
bitfld.long 0x04 27. " GDIR27 ,GPIO Direction 27 bit" "Input,Output"
|
|
bitfld.long 0x04 26. " GDIR26 ,GPIO Direction 26 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 25. " GDIR25 ,GPIO Direction 25 bit" "Input,Output"
|
|
bitfld.long 0x04 24. " GDIR24 ,GPIO Direction 24 bit" "Input,Output"
|
|
bitfld.long 0x04 23. " GDIR23 ,GPIO Direction 23 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 22. " GDIR22 ,GPIO Direction 22 bit" "Input,Output"
|
|
bitfld.long 0x04 21. " GDIR21 ,GPIO Direction 21 bit" "Input,Output"
|
|
bitfld.long 0x04 20. " GDIR20 ,GPIO Direction 20 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 19. " GDIR19 ,GPIO Direction 19 bit" "Input,Output"
|
|
bitfld.long 0x04 18. " GDIR18 ,GPIO Direction 18 bit" "Input,Output"
|
|
bitfld.long 0x04 17. " GDIR17 ,GPIO Direction 17 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 16. " GDIR16 ,GPIO Direction 16 bit" "Input,Output"
|
|
bitfld.long 0x04 15. " GDIR15 ,GPIO Direction 15 bit" "Input,Output"
|
|
bitfld.long 0x04 14. " GDIR14 ,GPIO Direction 14 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 13. " GDIR13 ,GPIO Direction 13 bit" "Input,Output"
|
|
bitfld.long 0x04 12. " GDIR12 ,GPIO Direction 12 bit" "Input,Output"
|
|
bitfld.long 0x04 11. " GDIR11 ,GPIO Direction 11 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 10. " GDIR10 ,GPIO Direction 10 bit" "Input,Output"
|
|
bitfld.long 0x04 9. " GDIR9 ,GPIO Direction 9 bit" "Input,Output"
|
|
bitfld.long 0x04 8. " GDIR8 ,GPIO Direction 8 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 7. " GDIR7 ,GPIO Direction 7 bit" "Input,Output"
|
|
bitfld.long 0x04 6. " GDIR6 ,GPIO Direction 6 bit" "Input,Output"
|
|
bitfld.long 0x04 5. " GDIR5 ,GPIO Direction 5 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 4. " GDIR4 ,GPIO Direction 4 bit" "Input,Output"
|
|
bitfld.long 0x04 3. " GDIR3 ,GPIO Direction 3 bit" "Input,Output"
|
|
bitfld.long 0x04 2. " GDIR2 ,GPIO Direction 2 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 1. " GDIR1 ,GPIO Direction 1 bit" "Input,Output"
|
|
bitfld.long 0x04 0. " GDIR0 ,GPIO Direction 0 bit" "Input,Output"
|
|
rgroup.long 0x08++0x3
|
|
line.long 0x00 "PSR,GPIO Pad Status Register"
|
|
bitfld.long 0x00 31. " PSR31 ,GPIO Pad Status bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " PSR30 ,GPIO Pad Status bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " PSR29 ,GPIO Pad Status bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " PSR28 ,GPIO Pad Status bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " PSR27 ,GPIO Pad Status bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " PSR26 ,GPIO Pad Status bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " PSR25 ,GPIO Pad Status bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " PSR24 ,GPIO Pad Status bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " PSR23 ,GPIO Pad Status bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " PSR22 ,GPIO Pad Status bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " PSR21 ,GPIO Pad Status bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " PSR20 ,GPIO Pad Status bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " PSR19 ,GPIO Pad Status bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " PSR18 ,GPIO Pad Status bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " PSR17 ,GPIO Pad Status bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PSR16 ,GPIO Pad Status bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " PSR15 ,GPIO Pad Status bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " PSR14 ,GPIO Pad Status bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " PSR13 ,GPIO Pad Status bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " PSR12 ,GPIO Pad Status bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " PSR11 ,GPIO Pad Status bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " PSR10 ,GPIO Pad Status bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " PSR9 ,GPIO Pad Status bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " PSR8 ,GPIO Pad Status bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " PSR7 ,GPIO Pad Status bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " PSR6 ,GPIO Pad Status bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " PSR5 ,GPIO Pad Status bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " PSR4 ,GPIO Pad Status bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " PSR3 ,GPIO Pad Status bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " PSR2 ,GPIO Pad Status bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " PSR1 ,GPIO Pad Status bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " PSR0 ,GPIO Pad Status bit 0" "Low,High"
|
|
tree "GPIO Interrupt Registers"
|
|
textline " "
|
|
group.long 0x0c++0xF
|
|
line.long 0x00 "ICR1,GPIO Interrupt Configuration Register 1"
|
|
bitfld.long 0x00 30.--31. " ICR1_15 ,Interrupt 15 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 28.--29. " ICR1_14 ,Interrupt 14 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 26.--27. " ICR1_13 ,Interrupt 13 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 24.--25. " ICR1_12 ,Interrupt 12 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " ICR1_11 ,Interrupt 11 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 20.--21. " ICR1_10 ,Interrupt 10 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " ICR1_9 ,Interrupt 9 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 16.--17. " ICR1_8 ,Interrupt 8 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " ICR1_7 ,Interrupt 7 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 12.--13. " ICR1_6 ,Interrupt 6 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " ICR1_5 ,Interrupt 5 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 8.--9. " ICR1_4 ,Interrupt 4 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " ICR1_3 ,Interrupt 3 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 4.--5. " ICR1_2 ,Interrupt 2 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " ICR1_1 ,Interrupt 1 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 0.--1. " ICR1_0 ,Interrupt 0 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x04 "ICR2,GPIO Interrupt Configuration Register 2"
|
|
bitfld.long 0x04 30.--31. " ICR2_31 ,Interrupt 31 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 28.--29. " ICR2_30 ,Interrupt 30 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 26.--27. " ICR2_29 ,Interrupt 29 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 24.--25. " ICR2_28 ,Interrupt 28 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 22.--23. " ICR2_27 ,Interrupt 27 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 20.--21. " ICR2_26 ,Interrupt 26 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " ICR2_25 ,Interrupt 25 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 16.--17. " ICR2_24 ,Interrupt 24 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 14.--15. " ICR2_23 ,Interrupt 23 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 12.--13. " ICR2_22 ,Interrupt 22 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 10.--11. " ICR2_21 ,Interrupt 21 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 8.--9. " ICR2_20 ,Interrupt 20 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 6.--7. " ICR2_19 ,Interrupt 19 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 4.--5. " ICR2_18 ,Interrupt 18 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 2.--3. " ICR2_17 ,Interrupt 17 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 0.--1. " ICR2_16 ,Interrupt 16 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x08 "IMR,GPIO Interrupt Mask Register"
|
|
bitfld.long 0x08 31. " IMR31 ,Interrupt 31 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 30. " IMR30 ,Interrupt 30 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 29. " IMR29 ,Interrupt 29 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 28. " IMR28 ,Interrupt 28 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 27. " IMR27 ,Interrupt 27 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 26. " IMR26 ,Interrupt 26 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 25. " IMR25 ,Interrupt 25 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " IMR24 ,Interrupt 24 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 23. " IMR23 ,Interrupt 23 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 22. " IMR22 ,Interrupt 22 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 21. " IMR21 ,Interrupt 21 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 20. " IMR20 ,Interrupt 20 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 19. " IMR19 ,Interrupt 19 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 18. " IMR18 ,Interrupt 18 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 17. " IMR17 ,Interrupt 17 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 16. " IMR16 ,Interrupt 16 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 15. " IMR15 ,Interrupt 15 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 14. " IMR14 ,Interrupt 14 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 13. " IMR13 ,Interrupt 13 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 12. " IMR12 ,Interrupt 12 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 11. " IMR11 ,Interrupt 11 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 10. " IMR10 ,Interrupt 10 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 9. " IMR9 ,Interrupt 9 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " IMR8 ,Interrupt 8 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " IMR7 ,Interrupt 7 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " IMR6 ,Interrupt 6 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 5. " IMR5 ,Interrupt 5 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 4. " IMR4 ,Interrupt 4 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 3. " IMR3 ,Interrupt 3 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " IMR2 ,Interrupt 2 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " IMR1 ,Interrupt 1 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " IMR0 ,Interrupt 0 Mask bit" "Disabled,Enabled"
|
|
line.long 0x0c "ISR,GPIO Interrupt Status Register"
|
|
eventfld.long 0x0c 31. " ISR31 ,Interrupt 31 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 30. " ISR30 ,Interrupt 30 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 29. " ISR29 ,Interrupt 29 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 28. " ISR28 ,Interrupt 28 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 27. " ISR27 ,Interrupt 27 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 26. " ISR26 ,Interrupt 26 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 25. " ISR25 ,Interrupt 25 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 24. " ISR24 ,Interrupt 24 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 23. " ISR23 ,Interrupt 23 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 22. " ISR22 ,Interrupt 22 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 21. " ISR21 ,Interrupt 21 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 20. " ISR20 ,Interrupt 20 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 19. " ISR19 ,Interrupt 19 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 18. " ISR18 ,Interrupt 18 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 17. " ISR17 ,Interrupt 17 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 16. " ISR16 ,Interrupt 16 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 15. " ISR15 ,Interrupt 15 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 14. " ISR14 ,Interrupt 14 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 13. " ISR13 ,Interrupt 13 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 12. " ISR12 ,Interrupt 12 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 11. " ISR11 ,Interrupt 11 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 10. " ISR10 ,Interrupt 10 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 9. " ISR9 ,Interrupt 9 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 8. " ISR8 ,Interrupt 8 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 7. " ISR7 ,Interrupt 7 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 6. " ISR6 ,Interrupt 6 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 5. " ISR5 ,Interrupt 5 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 4. " ISR4 ,Interrupt 4 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 3. " ISR3 ,Interrupt 3 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 2. " ISR2 ,Interrupt 2 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 1. " ISR1 ,Interrupt 1 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 0. " ISR0 ,Interrupt 0 Status bit" "No interrupt,Interrupt"
|
|
tree.end
|
|
width 0xB
|
|
group.long 0x1c++0x3
|
|
line.long 0x0 "EDGE_SEL,GPIO Edge Select Register"
|
|
bitfld.long 0x0 31. " EDGE_SEL31 ,Edge Selection 31" "ICR_2_31,Any edge"
|
|
bitfld.long 0x0 30. " EDGE_SEL30 ,Edge Selection 30" "ICR_2_30,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 29. " EDGE_SEL29 ,Edge Selection 29" "ICR_2_29,Any edge"
|
|
bitfld.long 0x0 28. " EDGE_SEL28 ,Edge Selection 28" "ICR_2_28,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 27. " EDGE_SEL27 ,Edge Selection 27" "ICR_2_27,Any edge"
|
|
bitfld.long 0x0 26. " EDGE_SEL26 ,Edge Selection 26" "ICR_2_26,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 25. " EDGE_SEL25 ,Edge Selection 25" "ICR_2_25,Any edge"
|
|
bitfld.long 0x0 24. " EDGE_SEL24 ,Edge Selection 24" "ICR_2_24,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 23. " EDGE_SEL23 ,Edge Selection 23" "ICR_2_23,Any edge"
|
|
bitfld.long 0x0 22. " EDGE_SEL22 ,Edge Selection 22" "ICR_2_22,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 21. " EDGE_SEL21 ,Edge Selection 21" "ICR_2_21,Any edge"
|
|
bitfld.long 0x0 20. " EDGE_SEL20 ,Edge Selection 20" "ICR_2_20,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 19. " EDGE_SEL19 ,Edge Selection 19" "ICR_2_19,Any edge"
|
|
bitfld.long 0x0 18. " EDGE_SEL18 ,Edge Selection 18" "ICR_2_18,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 17. " EDGE_SEL17 ,Edge Selection 17" "ICR_2_17,Any edge"
|
|
bitfld.long 0x0 16. " EDGE_SEL16 ,Edge Selection 16" "ICR_2_16,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 15. " EDGE_SEL15 ,Edge Selection 15" "ICR_1_15,Any edge"
|
|
bitfld.long 0x0 14. " EDGE_SEL14 ,Edge Selection 14" "ICR_1_14,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 13. " EDGE_SEL13 ,Edge Selection 13" "ICR_1_13,Any edge"
|
|
bitfld.long 0x0 12. " EDGE_SEL12 ,Edge Selection 12" "ICR_1_12,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 11. " EDGE_SEL11 ,Edge Selection 11" "ICR_1_11,Any edge"
|
|
bitfld.long 0x0 10. " EDGE_SEL10 ,Edge Selection 10" "ICR_1_10,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 9. " EDGE_SEL9 ,Edge Selection 9" "ICR_1_9,Any edge"
|
|
bitfld.long 0x0 8. " EDGE_SEL8 ,Edge Selection 8" "ICR_1_8,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 7. " EDGE_SEL7 ,Edge Selection 7" "ICR_1_7,Any edge"
|
|
bitfld.long 0x0 6. " EDGE_SEL6 ,Edge Selection 6" "ICR_1_6,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 5. " EDGE_SEL5 ,Edge Selection 5" "ICR_1_5,Any edge"
|
|
bitfld.long 0x0 4. " EDGE_SEL4 ,Edge Selection 4" "ICR_1_4,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 3. " EDGE_SEL3 ,Edge Selection 3" "ICR_1_3,Any edge"
|
|
bitfld.long 0x0 2. " EDGE_SEL2 ,Edge Selection 2" "ICR_1_2,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 1. " EDGE_SEL1 ,Edge Selection 1" "ICR_1_1,Any edge"
|
|
bitfld.long 0x0 0. " EDGE_SEL0 ,Edge Selection 0" "ICR_1_0,Any edge"
|
|
width 0xb
|
|
tree.end
|
|
tree "GPIO 3"
|
|
base ad:0x53fa4000
|
|
width 0x7
|
|
group.long 0x00++0x7
|
|
line.long 0x00 "DR,GPIO Data Register"
|
|
bitfld.long 0x00 31. " DR31 ,Data bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " DR30 ,Data bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " DR29 ,Data bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " DR28 ,Data bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " DR27 ,Data bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " DR26 ,Data bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DR25 ,Data bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " DR24 ,Data bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " DR23 ,Data bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DR22 ,Data bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " DR21 ,Data bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " DR20 ,Data bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " DR19 ,Data bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " DR18 ,Data bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " DR17 ,Data bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " DR16 ,Data bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " DR15 ,Data bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " DR14 ,Data bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " DR13 ,Data bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " DR12 ,Data bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " DR11 ,Data bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " DR10 ,Data bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " DR9 ,Data bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " DR8 ,Data bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " DR7 ,Data bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " DR6 ,Data bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " DR5 ,Data bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " DR4 ,Data bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " DR3 ,Data bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " DR2 ,Data bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " DR1 ,Data bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " DR0 ,Data bit 0" "Low,High"
|
|
line.long 0x04 "GDIR,GPIO Direction Register"
|
|
bitfld.long 0x04 31. " GDIR31 ,GPIO Direction 31 bit" "Input,Output"
|
|
bitfld.long 0x04 30. " GDIR30 ,GPIO Direction 30 bit" "Input,Output"
|
|
bitfld.long 0x04 29. " GDIR29 ,GPIO Direction 29 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 28. " GDIR28 ,GPIO Direction 28 bit" "Input,Output"
|
|
bitfld.long 0x04 27. " GDIR27 ,GPIO Direction 27 bit" "Input,Output"
|
|
bitfld.long 0x04 26. " GDIR26 ,GPIO Direction 26 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 25. " GDIR25 ,GPIO Direction 25 bit" "Input,Output"
|
|
bitfld.long 0x04 24. " GDIR24 ,GPIO Direction 24 bit" "Input,Output"
|
|
bitfld.long 0x04 23. " GDIR23 ,GPIO Direction 23 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 22. " GDIR22 ,GPIO Direction 22 bit" "Input,Output"
|
|
bitfld.long 0x04 21. " GDIR21 ,GPIO Direction 21 bit" "Input,Output"
|
|
bitfld.long 0x04 20. " GDIR20 ,GPIO Direction 20 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 19. " GDIR19 ,GPIO Direction 19 bit" "Input,Output"
|
|
bitfld.long 0x04 18. " GDIR18 ,GPIO Direction 18 bit" "Input,Output"
|
|
bitfld.long 0x04 17. " GDIR17 ,GPIO Direction 17 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 16. " GDIR16 ,GPIO Direction 16 bit" "Input,Output"
|
|
bitfld.long 0x04 15. " GDIR15 ,GPIO Direction 15 bit" "Input,Output"
|
|
bitfld.long 0x04 14. " GDIR14 ,GPIO Direction 14 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 13. " GDIR13 ,GPIO Direction 13 bit" "Input,Output"
|
|
bitfld.long 0x04 12. " GDIR12 ,GPIO Direction 12 bit" "Input,Output"
|
|
bitfld.long 0x04 11. " GDIR11 ,GPIO Direction 11 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 10. " GDIR10 ,GPIO Direction 10 bit" "Input,Output"
|
|
bitfld.long 0x04 9. " GDIR9 ,GPIO Direction 9 bit" "Input,Output"
|
|
bitfld.long 0x04 8. " GDIR8 ,GPIO Direction 8 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 7. " GDIR7 ,GPIO Direction 7 bit" "Input,Output"
|
|
bitfld.long 0x04 6. " GDIR6 ,GPIO Direction 6 bit" "Input,Output"
|
|
bitfld.long 0x04 5. " GDIR5 ,GPIO Direction 5 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 4. " GDIR4 ,GPIO Direction 4 bit" "Input,Output"
|
|
bitfld.long 0x04 3. " GDIR3 ,GPIO Direction 3 bit" "Input,Output"
|
|
bitfld.long 0x04 2. " GDIR2 ,GPIO Direction 2 bit" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x04 1. " GDIR1 ,GPIO Direction 1 bit" "Input,Output"
|
|
bitfld.long 0x04 0. " GDIR0 ,GPIO Direction 0 bit" "Input,Output"
|
|
rgroup.long 0x08++0x3
|
|
line.long 0x00 "PSR,GPIO Pad Status Register"
|
|
bitfld.long 0x00 31. " PSR31 ,GPIO Pad Status bit 31" "Low,High"
|
|
bitfld.long 0x00 30. " PSR30 ,GPIO Pad Status bit 30" "Low,High"
|
|
bitfld.long 0x00 29. " PSR29 ,GPIO Pad Status bit 29" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 28. " PSR28 ,GPIO Pad Status bit 28" "Low,High"
|
|
bitfld.long 0x00 27. " PSR27 ,GPIO Pad Status bit 27" "Low,High"
|
|
bitfld.long 0x00 26. " PSR26 ,GPIO Pad Status bit 26" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 25. " PSR25 ,GPIO Pad Status bit 25" "Low,High"
|
|
bitfld.long 0x00 24. " PSR24 ,GPIO Pad Status bit 24" "Low,High"
|
|
bitfld.long 0x00 23. " PSR23 ,GPIO Pad Status bit 23" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 22. " PSR22 ,GPIO Pad Status bit 22" "Low,High"
|
|
bitfld.long 0x00 21. " PSR21 ,GPIO Pad Status bit 21" "Low,High"
|
|
bitfld.long 0x00 20. " PSR20 ,GPIO Pad Status bit 20" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 19. " PSR19 ,GPIO Pad Status bit 19" "Low,High"
|
|
bitfld.long 0x00 18. " PSR18 ,GPIO Pad Status bit 18" "Low,High"
|
|
bitfld.long 0x00 17. " PSR17 ,GPIO Pad Status bit 17" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PSR16 ,GPIO Pad Status bit 16" "Low,High"
|
|
bitfld.long 0x00 15. " PSR15 ,GPIO Pad Status bit 15" "Low,High"
|
|
bitfld.long 0x00 14. " PSR14 ,GPIO Pad Status bit 14" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 13. " PSR13 ,GPIO Pad Status bit 13" "Low,High"
|
|
bitfld.long 0x00 12. " PSR12 ,GPIO Pad Status bit 12" "Low,High"
|
|
bitfld.long 0x00 11. " PSR11 ,GPIO Pad Status bit 11" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " PSR10 ,GPIO Pad Status bit 10" "Low,High"
|
|
bitfld.long 0x00 9. " PSR9 ,GPIO Pad Status bit 9" "Low,High"
|
|
bitfld.long 0x00 8. " PSR8 ,GPIO Pad Status bit 8" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 7. " PSR7 ,GPIO Pad Status bit 7" "Low,High"
|
|
bitfld.long 0x00 6. " PSR6 ,GPIO Pad Status bit 6" "Low,High"
|
|
bitfld.long 0x00 5. " PSR5 ,GPIO Pad Status bit 5" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 4. " PSR4 ,GPIO Pad Status bit 4" "Low,High"
|
|
bitfld.long 0x00 3. " PSR3 ,GPIO Pad Status bit 3" "Low,High"
|
|
bitfld.long 0x00 2. " PSR2 ,GPIO Pad Status bit 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 1. " PSR1 ,GPIO Pad Status bit 1" "Low,High"
|
|
bitfld.long 0x00 0. " PSR0 ,GPIO Pad Status bit 0" "Low,High"
|
|
tree "GPIO Interrupt Registers"
|
|
textline " "
|
|
group.long 0x0c++0xF
|
|
line.long 0x00 "ICR1,GPIO Interrupt Configuration Register 1"
|
|
bitfld.long 0x00 30.--31. " ICR1_15 ,Interrupt 15 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 28.--29. " ICR1_14 ,Interrupt 14 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 26.--27. " ICR1_13 ,Interrupt 13 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 24.--25. " ICR1_12 ,Interrupt 12 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " ICR1_11 ,Interrupt 11 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 20.--21. " ICR1_10 ,Interrupt 10 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " ICR1_9 ,Interrupt 9 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 16.--17. " ICR1_8 ,Interrupt 8 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " ICR1_7 ,Interrupt 7 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 12.--13. " ICR1_6 ,Interrupt 6 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " ICR1_5 ,Interrupt 5 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 8.--9. " ICR1_4 ,Interrupt 4 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " ICR1_3 ,Interrupt 3 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 4.--5. " ICR1_2 ,Interrupt 2 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " ICR1_1 ,Interrupt 1 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x00 0.--1. " ICR1_0 ,Interrupt 0 Configuration 1 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x04 "ICR2,GPIO Interrupt Configuration Register 2"
|
|
bitfld.long 0x04 30.--31. " ICR2_31 ,Interrupt 31 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 28.--29. " ICR2_30 ,Interrupt 30 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 26.--27. " ICR2_29 ,Interrupt 29 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 24.--25. " ICR2_28 ,Interrupt 28 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 22.--23. " ICR2_27 ,Interrupt 27 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 20.--21. " ICR2_26 ,Interrupt 26 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " ICR2_25 ,Interrupt 25 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 16.--17. " ICR2_24 ,Interrupt 24 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 14.--15. " ICR2_23 ,Interrupt 23 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 12.--13. " ICR2_22 ,Interrupt 22 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 10.--11. " ICR2_21 ,Interrupt 21 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 8.--9. " ICR2_20 ,Interrupt 20 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 6.--7. " ICR2_19 ,Interrupt 19 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 4.--5. " ICR2_18 ,Interrupt 18 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
textline " "
|
|
bitfld.long 0x04 2.--3. " ICR2_17 ,Interrupt 17 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
bitfld.long 0x04 0.--1. " ICR2_16 ,Interrupt 16 Configuration 2 bits" "Low-level,High-level,Rise-edge,Fall-edge"
|
|
line.long 0x08 "IMR,GPIO Interrupt Mask Register"
|
|
bitfld.long 0x08 31. " IMR31 ,Interrupt 31 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 30. " IMR30 ,Interrupt 30 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 29. " IMR29 ,Interrupt 29 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 28. " IMR28 ,Interrupt 28 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 27. " IMR27 ,Interrupt 27 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 26. " IMR26 ,Interrupt 26 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 25. " IMR25 ,Interrupt 25 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " IMR24 ,Interrupt 24 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 23. " IMR23 ,Interrupt 23 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 22. " IMR22 ,Interrupt 22 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 21. " IMR21 ,Interrupt 21 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 20. " IMR20 ,Interrupt 20 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 19. " IMR19 ,Interrupt 19 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 18. " IMR18 ,Interrupt 18 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 17. " IMR17 ,Interrupt 17 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 16. " IMR16 ,Interrupt 16 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 15. " IMR15 ,Interrupt 15 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 14. " IMR14 ,Interrupt 14 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 13. " IMR13 ,Interrupt 13 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 12. " IMR12 ,Interrupt 12 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 11. " IMR11 ,Interrupt 11 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 10. " IMR10 ,Interrupt 10 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 9. " IMR9 ,Interrupt 9 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " IMR8 ,Interrupt 8 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " IMR7 ,Interrupt 7 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " IMR6 ,Interrupt 6 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 5. " IMR5 ,Interrupt 5 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 4. " IMR4 ,Interrupt 4 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 3. " IMR3 ,Interrupt 3 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " IMR2 ,Interrupt 2 Mask bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " IMR1 ,Interrupt 1 Mask bit" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " IMR0 ,Interrupt 0 Mask bit" "Disabled,Enabled"
|
|
line.long 0x0c "ISR,GPIO Interrupt Status Register"
|
|
eventfld.long 0x0c 31. " ISR31 ,Interrupt 31 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 30. " ISR30 ,Interrupt 30 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 29. " ISR29 ,Interrupt 29 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 28. " ISR28 ,Interrupt 28 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 27. " ISR27 ,Interrupt 27 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 26. " ISR26 ,Interrupt 26 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 25. " ISR25 ,Interrupt 25 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 24. " ISR24 ,Interrupt 24 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 23. " ISR23 ,Interrupt 23 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 22. " ISR22 ,Interrupt 22 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 21. " ISR21 ,Interrupt 21 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 20. " ISR20 ,Interrupt 20 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 19. " ISR19 ,Interrupt 19 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 18. " ISR18 ,Interrupt 18 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 17. " ISR17 ,Interrupt 17 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 16. " ISR16 ,Interrupt 16 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 15. " ISR15 ,Interrupt 15 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 14. " ISR14 ,Interrupt 14 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 13. " ISR13 ,Interrupt 13 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 12. " ISR12 ,Interrupt 12 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 11. " ISR11 ,Interrupt 11 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 10. " ISR10 ,Interrupt 10 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 9. " ISR9 ,Interrupt 9 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 8. " ISR8 ,Interrupt 8 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 7. " ISR7 ,Interrupt 7 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 6. " ISR6 ,Interrupt 6 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 5. " ISR5 ,Interrupt 5 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 4. " ISR4 ,Interrupt 4 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 3. " ISR3 ,Interrupt 3 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 2. " ISR2 ,Interrupt 2 Status bit" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0c 1. " ISR1 ,Interrupt 1 Status bit" "No interrupt,Interrupt"
|
|
eventfld.long 0x0c 0. " ISR0 ,Interrupt 0 Status bit" "No interrupt,Interrupt"
|
|
tree.end
|
|
width 0xB
|
|
group.long 0x1c++0x3
|
|
line.long 0x0 "EDGE_SEL,GPIO Edge Select Register"
|
|
bitfld.long 0x0 31. " EDGE_SEL31 ,Edge Selection 31" "ICR_2_31,Any edge"
|
|
bitfld.long 0x0 30. " EDGE_SEL30 ,Edge Selection 30" "ICR_2_30,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 29. " EDGE_SEL29 ,Edge Selection 29" "ICR_2_29,Any edge"
|
|
bitfld.long 0x0 28. " EDGE_SEL28 ,Edge Selection 28" "ICR_2_28,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 27. " EDGE_SEL27 ,Edge Selection 27" "ICR_2_27,Any edge"
|
|
bitfld.long 0x0 26. " EDGE_SEL26 ,Edge Selection 26" "ICR_2_26,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 25. " EDGE_SEL25 ,Edge Selection 25" "ICR_2_25,Any edge"
|
|
bitfld.long 0x0 24. " EDGE_SEL24 ,Edge Selection 24" "ICR_2_24,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 23. " EDGE_SEL23 ,Edge Selection 23" "ICR_2_23,Any edge"
|
|
bitfld.long 0x0 22. " EDGE_SEL22 ,Edge Selection 22" "ICR_2_22,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 21. " EDGE_SEL21 ,Edge Selection 21" "ICR_2_21,Any edge"
|
|
bitfld.long 0x0 20. " EDGE_SEL20 ,Edge Selection 20" "ICR_2_20,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 19. " EDGE_SEL19 ,Edge Selection 19" "ICR_2_19,Any edge"
|
|
bitfld.long 0x0 18. " EDGE_SEL18 ,Edge Selection 18" "ICR_2_18,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 17. " EDGE_SEL17 ,Edge Selection 17" "ICR_2_17,Any edge"
|
|
bitfld.long 0x0 16. " EDGE_SEL16 ,Edge Selection 16" "ICR_2_16,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 15. " EDGE_SEL15 ,Edge Selection 15" "ICR_1_15,Any edge"
|
|
bitfld.long 0x0 14. " EDGE_SEL14 ,Edge Selection 14" "ICR_1_14,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 13. " EDGE_SEL13 ,Edge Selection 13" "ICR_1_13,Any edge"
|
|
bitfld.long 0x0 12. " EDGE_SEL12 ,Edge Selection 12" "ICR_1_12,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 11. " EDGE_SEL11 ,Edge Selection 11" "ICR_1_11,Any edge"
|
|
bitfld.long 0x0 10. " EDGE_SEL10 ,Edge Selection 10" "ICR_1_10,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 9. " EDGE_SEL9 ,Edge Selection 9" "ICR_1_9,Any edge"
|
|
bitfld.long 0x0 8. " EDGE_SEL8 ,Edge Selection 8" "ICR_1_8,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 7. " EDGE_SEL7 ,Edge Selection 7" "ICR_1_7,Any edge"
|
|
bitfld.long 0x0 6. " EDGE_SEL6 ,Edge Selection 6" "ICR_1_6,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 5. " EDGE_SEL5 ,Edge Selection 5" "ICR_1_5,Any edge"
|
|
bitfld.long 0x0 4. " EDGE_SEL4 ,Edge Selection 4" "ICR_1_4,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 3. " EDGE_SEL3 ,Edge Selection 3" "ICR_1_3,Any edge"
|
|
bitfld.long 0x0 2. " EDGE_SEL2 ,Edge Selection 2" "ICR_1_2,Any edge"
|
|
textline " "
|
|
bitfld.long 0x0 1. " EDGE_SEL1 ,Edge Selection 1" "ICR_1_1,Any edge"
|
|
bitfld.long 0x0 0. " EDGE_SEL0 ,Edge Selection 0" "ICR_1_0,Any edge"
|
|
width 0xb
|
|
tree.end
|
|
tree.end
|
|
tree.open "I2C (Inter IC)"
|
|
tree "I2C1"
|
|
base ad:0x43f80000
|
|
width 6.
|
|
group.word 0x00++0x1
|
|
line.word 0x00 "IADR,I2C Address Register"
|
|
hexmask.word.byte 0x00 1.--7. 0x2 " ADR ,Slave Address"
|
|
group.word 0x04++0x1
|
|
line.word 0x00 "IFDR,I2C Frequency Divider Register"
|
|
bitfld.word 0x00 0.--5. " IC ,I2C Clock Rate" "30,32,36,42,48,52,60,72,80,88,104,128,144,160,192,240,288,320,384,480,576,640,768,960,1152,1280,1536,1920,2304,2560,3072,3840,22,24,26,28,32,36,40,44,48,56,64,72,80,96,112,128,160,192,224,256,320,384,448,512,640,768,896,1024,1280,1536,1792,2048"
|
|
group.word 0x08++0x1
|
|
line.word 0x00 "I2CR,I2C Control Register"
|
|
bitfld.word 0x00 7. " IEN ,I2C Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 6. " IIEN ,I2C Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 5. " MSTA ,Master/Slave Mode Select" "Slave,Master"
|
|
textline " "
|
|
bitfld.word 0x00 4. " MTX ,Transmit/Receive Mode Select bit" "Receive,Transmit"
|
|
bitfld.word 0x00 3. " TXAK ,Transmit Acknowledge Enable" "Enabled,Disabled"
|
|
bitfld.word 0x00 2. " RSTA ,Repeat Start" "Not repeated,Repeated"
|
|
group.word 0x0c++0x1
|
|
line.word 0x00 "I2SR,I2C Status Register"
|
|
bitfld.word 0x00 7. " ICF ,Data transferring bit" "In progress,Completed"
|
|
bitfld.word 0x00 6. " IAAS ,I2C addressed as a slave bit" "Not addressed,Addressed"
|
|
bitfld.word 0x00 5. " IBB ,I2C bus busy bit" "Idle,Busy"
|
|
textline " "
|
|
bitfld.word 0x00 4. " IAL ,Arbitration lost" "Not lost,Lost"
|
|
bitfld.word 0x00 2. " SRW ,Slave read/write" "Write,Read"
|
|
bitfld.word 0x00 1. " IIF ,I2C interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.word 0x00 0. " RXAK ,Received acknowledge" "ACK,NACK"
|
|
group.word 0x10++0x1
|
|
line.word 0x00 "I2DR,I2C Data I/O Register"
|
|
hexmask.word.byte 0x00 0.--7. 1. " DATA ,Data Byte"
|
|
width 0xb
|
|
tree.end
|
|
tree "I2C2"
|
|
base ad:0x43f98000
|
|
width 6.
|
|
group.word 0x00++0x1
|
|
line.word 0x00 "IADR,I2C Address Register"
|
|
hexmask.word.byte 0x00 1.--7. 0x2 " ADR ,Slave Address"
|
|
group.word 0x04++0x1
|
|
line.word 0x00 "IFDR,I2C Frequency Divider Register"
|
|
bitfld.word 0x00 0.--5. " IC ,I2C Clock Rate" "30,32,36,42,48,52,60,72,80,88,104,128,144,160,192,240,288,320,384,480,576,640,768,960,1152,1280,1536,1920,2304,2560,3072,3840,22,24,26,28,32,36,40,44,48,56,64,72,80,96,112,128,160,192,224,256,320,384,448,512,640,768,896,1024,1280,1536,1792,2048"
|
|
group.word 0x08++0x1
|
|
line.word 0x00 "I2CR,I2C Control Register"
|
|
bitfld.word 0x00 7. " IEN ,I2C Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 6. " IIEN ,I2C Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 5. " MSTA ,Master/Slave Mode Select" "Slave,Master"
|
|
textline " "
|
|
bitfld.word 0x00 4. " MTX ,Transmit/Receive Mode Select bit" "Receive,Transmit"
|
|
bitfld.word 0x00 3. " TXAK ,Transmit Acknowledge Enable" "Enabled,Disabled"
|
|
bitfld.word 0x00 2. " RSTA ,Repeat Start" "Not repeated,Repeated"
|
|
group.word 0x0c++0x1
|
|
line.word 0x00 "I2SR,I2C Status Register"
|
|
bitfld.word 0x00 7. " ICF ,Data transferring bit" "In progress,Completed"
|
|
bitfld.word 0x00 6. " IAAS ,I2C addressed as a slave bit" "Not addressed,Addressed"
|
|
bitfld.word 0x00 5. " IBB ,I2C bus busy bit" "Idle,Busy"
|
|
textline " "
|
|
bitfld.word 0x00 4. " IAL ,Arbitration lost" "Not lost,Lost"
|
|
bitfld.word 0x00 2. " SRW ,Slave read/write" "Write,Read"
|
|
bitfld.word 0x00 1. " IIF ,I2C interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.word 0x00 0. " RXAK ,Received acknowledge" "ACK,NACK"
|
|
group.word 0x10++0x1
|
|
line.word 0x00 "I2DR,I2C Data I/O Register"
|
|
hexmask.word.byte 0x00 0.--7. 1. " DATA ,Data Byte"
|
|
width 0xb
|
|
tree.end
|
|
tree "I2C3"
|
|
base ad:0x43f84000
|
|
width 6.
|
|
group.word 0x00++0x1
|
|
line.word 0x00 "IADR,I2C Address Register"
|
|
hexmask.word.byte 0x00 1.--7. 0x2 " ADR ,Slave Address"
|
|
group.word 0x04++0x1
|
|
line.word 0x00 "IFDR,I2C Frequency Divider Register"
|
|
bitfld.word 0x00 0.--5. " IC ,I2C Clock Rate" "30,32,36,42,48,52,60,72,80,88,104,128,144,160,192,240,288,320,384,480,576,640,768,960,1152,1280,1536,1920,2304,2560,3072,3840,22,24,26,28,32,36,40,44,48,56,64,72,80,96,112,128,160,192,224,256,320,384,448,512,640,768,896,1024,1280,1536,1792,2048"
|
|
group.word 0x08++0x1
|
|
line.word 0x00 "I2CR,I2C Control Register"
|
|
bitfld.word 0x00 7. " IEN ,I2C Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 6. " IIEN ,I2C Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.word 0x00 5. " MSTA ,Master/Slave Mode Select" "Slave,Master"
|
|
textline " "
|
|
bitfld.word 0x00 4. " MTX ,Transmit/Receive Mode Select bit" "Receive,Transmit"
|
|
bitfld.word 0x00 3. " TXAK ,Transmit Acknowledge Enable" "Enabled,Disabled"
|
|
bitfld.word 0x00 2. " RSTA ,Repeat Start" "Not repeated,Repeated"
|
|
group.word 0x0c++0x1
|
|
line.word 0x00 "I2SR,I2C Status Register"
|
|
bitfld.word 0x00 7. " ICF ,Data transferring bit" "In progress,Completed"
|
|
bitfld.word 0x00 6. " IAAS ,I2C addressed as a slave bit" "Not addressed,Addressed"
|
|
bitfld.word 0x00 5. " IBB ,I2C bus busy bit" "Idle,Busy"
|
|
textline " "
|
|
bitfld.word 0x00 4. " IAL ,Arbitration lost" "Not lost,Lost"
|
|
bitfld.word 0x00 2. " SRW ,Slave read/write" "Write,Read"
|
|
bitfld.word 0x00 1. " IIF ,I2C interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.word 0x00 0. " RXAK ,Received acknowledge" "ACK,NACK"
|
|
group.word 0x10++0x1
|
|
line.word 0x00 "I2DR,I2C Data I/O Register"
|
|
hexmask.word.byte 0x00 0.--7. 1. " DATA ,Data Byte"
|
|
width 0xb
|
|
tree.end
|
|
tree.end
|
|
tree "KPP (Keypad Port)"
|
|
base ad:0x43fa8000
|
|
width 6.
|
|
group.word 0x00++0x7
|
|
line.word 0x00 "KPCR,Keypad Control Register"
|
|
bitfld.word 0x00 15. " KCO7 ,Keypad Column Strobe Open-Drain Enable 7" "Totem pole,Open drain"
|
|
bitfld.word 0x00 14. " KCO6 ,Keypad Column Strobe Open-Drain Enable 6" "Totem pole,Open drain"
|
|
bitfld.word 0x00 13. " KCO5 ,Keypad Column Strobe Open-Drain Enable 5" "Totem pole,Open drain"
|
|
textline " "
|
|
bitfld.word 0x00 12. " KCO4 ,Keypad Column Strobe Open-Drain Enable 4" "Totem pole,Open drain"
|
|
bitfld.word 0x00 11. " KCO3 ,Keypad Column Strobe Open-Drain Enable 3" "Totem pole,Open drain"
|
|
bitfld.word 0x00 10. " KCO2 ,Keypad Column Strobe Open-Drain Enable 2" "Totem pole,Open drain"
|
|
textline " "
|
|
bitfld.word 0x00 9. " KCO1 ,Keypad Column Strobe Open-Drain Enable 1" "Totem pole,Open drain"
|
|
bitfld.word 0x00 8. " KCO0 ,Keypad Column Strobe Open-Drain Enable 0" "Totem pole,Open drain"
|
|
bitfld.word 0x00 7. " KRE7 ,Keypad Row Enable 7" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 6. " KRE6 ,Keypad Row Enable 6" "Disabled,Enabled"
|
|
bitfld.word 0x00 5. " KRE5 ,Keypad Row Enable 5" "Disabled,Enabled"
|
|
bitfld.word 0x00 4. " KRE4 ,Keypad Row Enable 4" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 3. " KRE3 ,Keypad Row Enable 3" "Disabled,Enabled"
|
|
bitfld.word 0x00 2. " KRE2 ,Keypad Row Enable 2" "Disabled,Enabled"
|
|
bitfld.word 0x00 1. " KRE1 ,Keypad Row Enable 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 0. " KRE0 ,Keypad Row Enable 0" "Disabled,Enabled"
|
|
line.word 0x02 "KPSR,Keypad Status Register"
|
|
bitfld.word 0x02 9. " KRIE ,Keypad Release Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.word 0x02 8. " KDIE ,Keypad Key Depress Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x02 3. " KRSS ,Key Release Synchronizer Set" "No effect,Set"
|
|
bitfld.word 0x02 2. " KDSC ,Key Depress Synchronizer Clear" "No effect,Cleared"
|
|
eventfld.word 0x02 1. " KPKR ,Keypad Key Release" "Not released,Released"
|
|
textline " "
|
|
eventfld.word 0x02 0. " KPKD ,Keypad Key Depress" "Not depressed,Depressed"
|
|
line.word 0x04 "KDDR,Keypad Data Direction Register"
|
|
bitfld.word 0x04 15. " KCDD7 ,Keypad Column Data Direction 7" "Input,Output"
|
|
bitfld.word 0x04 14. " KCDD6 ,Keypad Column Data Direction 6" "Input,Output"
|
|
bitfld.word 0x04 13. " KCDD5 ,Keypad Column Data Direction 5" "Input,Output"
|
|
textline " "
|
|
bitfld.word 0x04 12. " KCDD4 ,Keypad Column Data Direction 4" "Input,Output"
|
|
bitfld.word 0x04 11. " KCDD3 ,Keypad Column Data Direction 3" "Input,Output"
|
|
bitfld.word 0x04 10. " KCDD2 ,Keypad Column Data Direction 2" "Input,Output"
|
|
textline " "
|
|
bitfld.word 0x04 9. " KCDD1 ,Keypad Column Data Direction 1" "Input,Output"
|
|
bitfld.word 0x04 8. " KCDD0 ,Keypad Column Data Direction 0" "Input,Output"
|
|
bitfld.word 0x04 7. " KRDD7 ,Keypad Row Data Direction 7" "Input,Output"
|
|
textline " "
|
|
bitfld.word 0x04 6. " KRDD6 ,Keypad Row Data Direction 6" "Input,Output"
|
|
bitfld.word 0x04 5. " KRDD5 ,Keypad Row Data Direction 5" "Input,Output"
|
|
bitfld.word 0x04 4. " KRDD4 ,Keypad Row Data Direction 4" "Input,Output"
|
|
textline " "
|
|
bitfld.word 0x04 3. " KRDD3 ,Keypad Row Data Direction 3" "Input,Output"
|
|
bitfld.word 0x04 2. " KRDD2 ,Keypad Row Data Direction 2" "Input,Output"
|
|
bitfld.word 0x04 1. " KRDD1 ,Keypad Row Data Direction 1" "Input,Output"
|
|
textline " "
|
|
bitfld.word 0x04 0. " KRDD0 ,Keypad Row Data Direction 0" "Input,Output"
|
|
line.word 0x06 "KPDR,Keypad Data Register"
|
|
bitfld.word 0x06 15. " KCD7 ,Keypad Column Data 7" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 14. " KCD6 ,Keypad Column Data 6" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 13. " KCD5 ,Keypad Column Data 5" "Pin=0,Pin=1"
|
|
textline " "
|
|
bitfld.word 0x06 12. " KCD4 ,Keypad Column Data 4" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 11. " KCD3 ,Keypad Column Data 3" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 10. " KCD2 ,Keypad Column Data 2" "Pin=0,Pin=1"
|
|
textline " "
|
|
bitfld.word 0x06 9. " KCD1 ,Keypad Column Data 1" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 8. " KCD0 ,Keypad Column Data 0" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 7. " KRD7 ,Keypad Row Data 7" "Pin=0,Pin=1"
|
|
textline " "
|
|
bitfld.word 0x06 6. " KRD6 ,Keypad Row Data 6" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 5. " KRD5 ,Keypad Row Data 5" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 4. " KRD4 ,Keypad Row Data 4" "Pin=0,Pin=1"
|
|
textline " "
|
|
bitfld.word 0x06 3. " KRD3 ,Keypad Row Data 3" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 2. " KRD2 ,Keypad Row Data 2" "Pin=0,Pin=1"
|
|
bitfld.word 0x06 1. " KRD1 ,Keypad Row Data 1" "Pin=0,Pin=1"
|
|
textline " "
|
|
bitfld.word 0x06 0. " KRD0 ,Keypad Row Data 0" "Pin=0,Pin=1"
|
|
width 0xb
|
|
tree.end
|
|
tree "MLB DIM (Media Local Bus Device Interface Macro)"
|
|
base ad:0x53ff8000
|
|
width 9.
|
|
group.long 0x00++0x07
|
|
line.long 0x00 "DCCR,Device Control Cfg Register"
|
|
bitfld.long 0x00 31. " MDE ,MediaLB Device Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " LBM ,Loop-Back Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " MCS ,MediaLB Clock Select" "256Fs,512Fs,1024Fs,?..."
|
|
bitfld.long 0x00 26. " MLK ,MediaLB Lock" "Not synchronized,Synchronized"
|
|
textline " "
|
|
bitfld.long 0x00 24. " MHRE ,MediaLB Hardware Reset Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 23. " MRS ,MediaLB Software Reset" "No reset,Reset"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " MDA ,MediaLB Device Address"
|
|
line.long 0x04 "SSCR,System Status Cfg Register"
|
|
bitfld.long 0x04 7. " SSRE ,System Service Request Enable" "Device Present,Device Service Request"
|
|
textline " "
|
|
bitfld.long 0x04 6. " SDMU ,System Detects MediaLB Unlock" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " SDML ,System Detects MediaLB Lock" "Not detected,Detected"
|
|
bitfld.long 0x04 4. " SDSC ,System Detects SubCommand" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 3. " SDCS ,System Detects Channel Scan" "Not detected,Detected"
|
|
bitfld.long 0x04 2. " SDNU ,System Detects Network Unlock" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 1. " SDNL ,System Detects Network Lock" "Not detected,Detected"
|
|
bitfld.long 0x04 0. " SDR ,System Detects Reset" "Not detected,Detected"
|
|
rgroup.long 0x08++0x03
|
|
line.long 0x00 "SDCR,System Data Cfg Register"
|
|
group.long 0x0c++0x03
|
|
line.long 0x00 "SMCR,System Mask Cfg Register"
|
|
bitfld.long 0x00 6. " SMMU ,System Masks MediaLB Unlock" "Not masked,Masked"
|
|
bitfld.long 0x00 5. " SMML ,System Masks MediaLB Lock" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 4. " SMSC ,System Masks SubCommand" "Not masked,Masked"
|
|
bitfld.long 0x00 3. " SMCS ,System Masks Channel Scan" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 2. " SMNU ,System Masks Network Unlock" "Not masked,Masked"
|
|
bitfld.long 0x00 1. " SMNL ,System Masks Network Lock" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SMR ,System Masks Reset" "Not masked,Masked"
|
|
rgroup.long 0x1c++0x13
|
|
line.long 0x00 "VCCR,Version Control Configuration Register"
|
|
hexmask.long.byte 0x00 24.--31. 1. " UMA ,User Major Revision Code"
|
|
hexmask.long.byte 0x00 16.--23. 1. " UMI ,User Minor Revision Code"
|
|
hexmask.long.byte 0x00 8.--15. 1. " MMA ,MediaLB Major Revision Code"
|
|
hexmask.long.byte 0x00 0.--7. 1. " MMI ,MediaLB Minor Revision Code"
|
|
line.long 0x04 "SBCR,Synchronous Base Address Cfg Register"
|
|
hexmask.long.word 0x04 16.--31. 1. " SRBA ,Synchronous Receive Base Address"
|
|
hexmask.long.word 0x04 0.--15. 1. " STBA ,Synchronous Transmit Base Address"
|
|
line.long 0x08 "ABCR,Asynchronous Base Address Cfg Register"
|
|
hexmask.long.word 0x08 16.--31. 1. " ARBA ,Asynchronous Receive Base Address"
|
|
hexmask.long.word 0x08 0.--15. 1. " ATBA ,Asynchronous Transmit Base Address"
|
|
line.long 0x0c "CBCR,Control Base Address Cfg Register"
|
|
hexmask.long.word 0x0c 16.--31. 1. " CRBA ,Control Receive Base Address"
|
|
hexmask.long.word 0x0c 0.--15. 1. " CTBA ,Control Transmit Base Address"
|
|
line.long 0x10 "IBCR,Isochronous Base Address Cfg Register"
|
|
hexmask.long.word 0x10 16.--31. 1. " IRBA ,Isochronous Receive Base Address"
|
|
hexmask.long.word 0x10 0.--15. 1. " ITBA ,Isochronous Transmit Base Address"
|
|
group.long 0x30++0x03
|
|
line.long 0x00 "CICR,Channel Interrupt Cfg Register"
|
|
bitfld.long 0x00 15. " C15SU ,Channel 15 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 14. " C14SU ,Channel 14 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 13. " C13SU ,Channel 13 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 12. " C12SU ,Channel 12 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 11. " C11SU ,Channel 11 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 10. " C10SU ,Channel 10 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 9. " C09SU ,Channel 9 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 8. " C08SU ,Channel 8 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 7. " C07SU ,Channel 7 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 6. " C06SU ,Channel 6 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 5. " C05SU ,Channel 5 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 4. " C04SU ,Channel 4 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 3. " C03SU ,Channel 3 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 2. " C02SU ,Channel 2 Status Update" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 1. " C01SU ,Channel 1 Status Update" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 0. " C00SU ,Channel 0 Status Update" "No interrupt,Interrupt"
|
|
tree "Channel 0"
|
|
if (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x00)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x40000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x10000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x50000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x20000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x60000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x40))&0x70000000)==0x30000000)
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x40++0x7
|
|
line.long 0x00 "CECR0,Channel 0 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 0 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 0 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 0 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 0 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR0,Channel 0 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x40+0x08)++0x03
|
|
line.long 0x00 "CCBCR0,Channel 0 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x40+0x0c)++0x03
|
|
line.long 0x00 "CNBCR0,Channel 0 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x280++0x03 "Local Channel 0"
|
|
line.long 0x00 "LCBCR0,Local Channel 0 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 1"
|
|
if (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x00)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x40000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x10000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x50000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x20000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x60000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x50))&0x70000000)==0x30000000)
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "CECR1,Channel 1 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 1 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 1 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 1 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR1,Channel 1 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x50+0x08)++0x03
|
|
line.long 0x00 "CCBCR1,Channel 1 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x50+0x0c)++0x03
|
|
line.long 0x00 "CNBCR1,Channel 1 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x284++0x03 "Local Channel 1"
|
|
line.long 0x00 "LCBCR1,Local Channel 1 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 2"
|
|
if (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x00)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x40000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x10000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x50000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x20000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x60000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x60))&0x70000000)==0x30000000)
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x60++0x7
|
|
line.long 0x00 "CECR2,Channel 2 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 2 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 2 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 2 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 2 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR2,Channel 2 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x60+0x08)++0x03
|
|
line.long 0x00 "CCBCR2,Channel 2 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x60+0x0c)++0x03
|
|
line.long 0x00 "CNBCR2,Channel 2 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x288++0x03 "Local Channel 2"
|
|
line.long 0x00 "LCBCR2,Local Channel 2 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 3"
|
|
if (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x00)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x40000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x10000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x50000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x20000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x60000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x70))&0x70000000)==0x30000000)
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "CECR3,Channel 3 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 3 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 3 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 3 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR3,Channel 3 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x70+0x08)++0x03
|
|
line.long 0x00 "CCBCR3,Channel 3 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x70+0x0c)++0x03
|
|
line.long 0x00 "CNBCR3,Channel 3 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x28C++0x03 "Local Channel 3"
|
|
line.long 0x00 "LCBCR3,Local Channel 3 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 4"
|
|
if (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x00)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x40000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x10000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x50000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x20000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x60000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x80))&0x70000000)==0x30000000)
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x80++0x7
|
|
line.long 0x00 "CECR4,Channel 4 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 4 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 4 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 4 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 4 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR4,Channel 4 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x80+0x08)++0x03
|
|
line.long 0x00 "CCBCR4,Channel 4 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x80+0x0c)++0x03
|
|
line.long 0x00 "CNBCR4,Channel 4 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x290++0x03 "Local Channel 4"
|
|
line.long 0x00 "LCBCR4,Local Channel 4 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 5"
|
|
if (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x00)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x40000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x10000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x50000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x20000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x60000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x90))&0x70000000)==0x30000000)
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x90++0x7
|
|
line.long 0x00 "CECR5,Channel 5 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 5 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 5 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 5 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR5,Channel 5 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x90+0x08)++0x03
|
|
line.long 0x00 "CCBCR5,Channel 5 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x90+0x0c)++0x03
|
|
line.long 0x00 "CNBCR5,Channel 5 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x294++0x03 "Local Channel 5"
|
|
line.long 0x00 "LCBCR5,Local Channel 5 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 6"
|
|
if (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x00)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x40000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x10000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x50000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x20000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x60000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xA0))&0x70000000)==0x30000000)
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xA0++0x7
|
|
line.long 0x00 "CECR6,Channel 6 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 6 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 6 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 6 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 6 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR6,Channel 6 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xA0+0x08)++0x03
|
|
line.long 0x00 "CCBCR6,Channel 6 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xA0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR6,Channel 6 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x298++0x03 "Local Channel 6"
|
|
line.long 0x00 "LCBCR6,Local Channel 6 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 7"
|
|
if (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x00)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x40000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x10000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x50000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x20000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x60000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xB0))&0x70000000)==0x30000000)
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xB0++0x7
|
|
line.long 0x00 "CECR7,Channel 7 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 7 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 7 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 7 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR7,Channel 7 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xB0+0x08)++0x03
|
|
line.long 0x00 "CCBCR7,Channel 7 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xB0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR7,Channel 7 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x29C++0x03 "Local Channel 7"
|
|
line.long 0x00 "LCBCR7,Local Channel 7 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 8"
|
|
if (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x00)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x40000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x10000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x50000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x20000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x60000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xC0))&0x70000000)==0x30000000)
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xC0++0x7
|
|
line.long 0x00 "CECR8,Channel 8 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 8 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 8 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 8 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 8 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR8,Channel 8 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xC0+0x08)++0x03
|
|
line.long 0x00 "CCBCR8,Channel 8 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xC0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR8,Channel 8 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2A0++0x03 "Local Channel 8"
|
|
line.long 0x00 "LCBCR8,Local Channel 8 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 9"
|
|
if (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x00)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x40000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x10000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x50000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x20000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x60000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xD0))&0x70000000)==0x30000000)
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xD0++0x7
|
|
line.long 0x00 "CECR9,Channel 9 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 9 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 9 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 9 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR9,Channel 9 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xD0+0x08)++0x03
|
|
line.long 0x00 "CCBCR9,Channel 9 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xD0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR9,Channel 9 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2A4++0x03 "Local Channel 9"
|
|
line.long 0x00 "LCBCR9,Local Channel 9 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 10"
|
|
if (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x00)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x40000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x10000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x50000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x20000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x60000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xE0))&0x70000000)==0x30000000)
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xE0++0x7
|
|
line.long 0x00 "CECR10,Channel 10 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 10 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 10 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 10 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 10 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR10,Channel 10 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xE0+0x08)++0x03
|
|
line.long 0x00 "CCBCR10,Channel 10 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xE0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR10,Channel 10 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2A8++0x03 "Local Channel 10"
|
|
line.long 0x00 "LCBCR10,Local Channel 10 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 11"
|
|
if (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x00)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x40000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x10000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x50000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x20000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x60000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0xF0))&0x70000000)==0x30000000)
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0xF0++0x7
|
|
line.long 0x00 "CECR11,Channel 11 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 11 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 11 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 11 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR11,Channel 11 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0xF0+0x08)++0x03
|
|
line.long 0x00 "CCBCR11,Channel 11 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0xF0+0x0c)++0x03
|
|
line.long 0x00 "CNBCR11,Channel 11 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2AC++0x03 "Local Channel 11"
|
|
line.long 0x00 "LCBCR11,Local Channel 11 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 12"
|
|
if (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x00)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x40000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x10000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x50000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x20000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x60000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x100))&0x70000000)==0x30000000)
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x100++0x7
|
|
line.long 0x00 "CECR12,Channel 12 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 12 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 12 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 12 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 12 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR12,Channel 12 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x100+0x08)++0x03
|
|
line.long 0x00 "CCBCR12,Channel 12 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x100+0x0c)++0x03
|
|
line.long 0x00 "CNBCR12,Channel 12 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2B0++0x03 "Local Channel 12"
|
|
line.long 0x00 "LCBCR12,Local Channel 12 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 13"
|
|
if (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x00)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x40000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x10000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x50000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x20000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x60000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x110))&0x70000000)==0x30000000)
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x110++0x7
|
|
line.long 0x00 "CECR13,Channel 13 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 13 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 13 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 13 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR13,Channel 13 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x110+0x08)++0x03
|
|
line.long 0x00 "CCBCR13,Channel 13 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x110+0x0c)++0x03
|
|
line.long 0x00 "CNBCR13,Channel 13 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2B4++0x03 "Local Channel 13"
|
|
line.long 0x00 "LCBCR13,Local Channel 13 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 14"
|
|
if (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x00)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x40000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x10000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x50000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x20000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x60000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x120))&0x70000000)==0x30000000)
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x120++0x7
|
|
line.long 0x00 "CECR14,Channel 14 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 14 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 14 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 14 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 14 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR14,Channel 14 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x120+0x08)++0x03
|
|
line.long 0x00 "CCBCR14,Channel 14 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x120+0x0c)++0x03
|
|
line.long 0x00 "CNBCR14,Channel 14 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2B8++0x03 "Local Channel 14"
|
|
line.long 0x00 "LCBCR14,Local Channel 14 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
tree "Channel 15"
|
|
if (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x00)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x40000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FSE ,Frame Synchronization Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " FSCD ,Frame Synchronization Channel Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " FSPC ,Frame Synchronization Physical Channel Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " LFS ,Lost Frame Synchronization" "Not lost,Lost"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x10000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 18.--19. " IVB ,Isochronous Valid Bytes" "BCA-5,BCA-4,BCA-3,BCA-2"
|
|
bitfld.long 0x04 17. " GIRB ,Generate Isochronous Receive Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
eventfld.long 0x04 4. " BE ,Buffer Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x50000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
bitfld.long 0x00 27. " FCE ,Flow Control Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
textline " "
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " IPL ,Isochronous Packet Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BCA ,Buffer Current Address"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--15. 1. " BFA ,Buffer Final Address"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x20000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x60000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
elif (((data.long(asd:0x53ff8000+0x130))&0x70000000)==0x30000000)
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
else
|
|
group.long 0x130++0x7
|
|
line.long 0x00 "CECR15,Channel 15 Entry Cfg Register"
|
|
bitfld.long 0x00 31. " CE ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " TR ,Channel 15 Transmit Select" "Receive,Transmit"
|
|
textline " "
|
|
bitfld.long 0x00 28.--29. " CT ,Channel 15 Type Select" "Synchronous,Isochronous,Asynchronous,Control"
|
|
textline " "
|
|
bitfld.long 0x00 25.--26. " MDS ,Channel 15 Mode Select" "Ping-pong buffering,Circular buffering,?..."
|
|
bitfld.long 0x00 22. " MLFS ,Mask Lost Frame Synchronization" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20. " MBE ,Mask Buffer Error" "Not masked,Masked"
|
|
bitfld.long 0x00 19. " MBS ,Mask Buffer Start" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 18. " MBD ,Mask Buffer Done" "Not masked,Masked"
|
|
bitfld.long 0x00 17. " MDB ,Mask Detect Break" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 16. " MPE ,Mask Protocol Error" "Not masked,Masked"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CA ,Channel Address"
|
|
line.long 0x04 "CSCR15,Channel 15 Status Cfg Register"
|
|
bitfld.long 0x04 31. " BM ,Buffer Empty" "Not empty,Empty"
|
|
bitfld.long 0x04 30. " BF ,Buffer Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x04 17. " GB ,Generate Break" "Not generated,Generated"
|
|
textline " "
|
|
bitfld.long 0x04 16. " RDY ,Next Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x04 11. " PBS ,Previous Buffer Start" "Not started,Started"
|
|
textline " "
|
|
bitfld.long 0x04 10. " PBD ,Previous Buffer Done" "Not finished,Finished"
|
|
eventfld.long 0x04 9. " PBDB ,Previous Buffer Detect Break" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 8. " PBPE ,Previous Buffer Protocol Error" "Not detected,Detected"
|
|
textline " "
|
|
bitfld.long 0x04 5. " ABE ,AHB Bus Error" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 3. " CBS ,Current Buffer Start" "Not started,Started"
|
|
eventfld.long 0x04 2. " CBD ,Current Buffer Done" "Not finished,Finished"
|
|
textline " "
|
|
eventfld.long 0x04 1. " CBDB ,Current Buffer Detect Break" "Not detected,Detected"
|
|
eventfld.long 0x04 0. " CBPE ,Current Buffer Protocol Error" "Not detected,Detected"
|
|
rgroup.long (0x130+0x08)++0x03
|
|
line.long 0x00 "CCBCR15,Channel 15 Current Buffer Cfg Register"
|
|
hexmask.long.word 0x00 18.--31. 0x04 " BCA ,Buffer Current Address"
|
|
hexmask.long.byte 0x00 16.--17. 1. " HW1 ,Hard-wired to 00"
|
|
textline " "
|
|
hexmask.long.word 0x00 2.--15. 0x04 " BFA ,Buffer Final Address"
|
|
hexmask.long.byte 0x00 0.--1. 1. " HW0 ,Hard-wired to 00"
|
|
endif
|
|
group.long (0x130+0x0c)++0x03
|
|
line.long 0x00 "CNBCR15,Channel 15 Next Buffer Cfg Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " BSA ,Buffer Start Address"
|
|
hexmask.long.word 0x00 0.--15. 1. " BEA ,Buffer End Address"
|
|
group.long 0x2BC++0x03 "Local Channel 15"
|
|
line.long 0x00 "LCBCR15,Local Channel 15 Buffer Cfg Register"
|
|
hexmask.long.word 0x00 22.--31. 1. " TH ,Buffer Threshold"
|
|
hexmask.long.word 0x00 13.--21. 1. " BD ,Buffer Depth"
|
|
hexmask.long.word 0x00 0.--12. 1. " SA ,Buffer Start Address"
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree "MSHC (Memory Stick Host Controller)"
|
|
base ad:0x50024000
|
|
width 6.
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "CMDR,Command register"
|
|
hexmask.long.byte 0x00 16.--23. 1. " TOVW ,Time Out Value for Wait"
|
|
hexmask.long.byte 0x00 8.--15. 1. " DSZ[7:0] ,Data Size [7:0] bits (If DSZ[9:0] = 0 than Size = 1024)"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " TPC ,Transfer Protocol Code" "Reserved,Reserved,READ_LONG_DATA,READ_SHORT_DATA,READ_REG,Reserved,Reserved,GET_INT,SET_RW_REG_ADRS,EX_SET_CMD,Reserved,WRITE_REG,WRITE_SHORT_DATA,WRITE_LONG_DATA,SET_CMD,?..."
|
|
bitfld.long 0x00 2. " DSL ,Data Select" "Internal FIFO,Not supported"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--1. 1. " DSZ[9:8] ,Data Size [9:8] bits (If DSZ[9:0] = 0 than Size = 1024)"
|
|
hgroup.long 0x08++0x3
|
|
hide.long 0x00 "DATR,Data register"
|
|
in
|
|
if ((d.l(asd:(0x50024000+0x18))&0x40)==0x0)
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "STAR,Status register"
|
|
eventfld.long 0x00 23. " IDA ,Illegal Data Access" "Legal,Illegal"
|
|
eventfld.long 0x00 22. " IXFR ,Illegal Transfer" "Legal,Illegal"
|
|
textline " "
|
|
eventfld.long 0x00 19. " WFUL ,Write to FIFO when Full" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " REMP ,Read from FIFO when Empty" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " Hresp_Error ,Hresp Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 13. " EMP ,FIFO Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 12. " FUL ,FIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 11. " CED ,MSPro Command End" "Not ended,Ended"
|
|
bitfld.long 0x00 10. " ERR ,MSPro Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 9. " BRQ ,MSPro Data Buffer Request" "Not requested,Requested"
|
|
bitfld.long 0x00 8. " CNK ,MSPro Command No Acknowledge" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x00 6. " DRQ ,DMA Request" "Not requested,Requested"
|
|
bitfld.long 0x00 5. " MSINT ,MS/Pro I/F Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RDY ,Ready for protocol execution" "Not ready,Ready"
|
|
bitfld.long 0x00 1. " CRC ,CRC Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TOE ,Time Out Error" "No error,Error"
|
|
else
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "STAR,Status register"
|
|
eventfld.long 0x00 23. " IDA ,Illegal Data Access" "Legal,Illegal"
|
|
eventfld.long 0x00 22. " IXFR ,Illegal Transfer" "Legal,Illegal"
|
|
textline " "
|
|
eventfld.long 0x00 19. " WFUL ,Write to FIFO when Full" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " REMP ,Read from FIFO when Empty" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " Hresp_Error ,Hresp Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 13. " EMP ,FIFO Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 12. " FUL ,FIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 6. " DRQ ,DMA Request" "Not requested,Requested"
|
|
bitfld.long 0x00 5. " MSINT ,MS/Pro I/F Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 4. " RDY ,Ready for protocol execution" "Not ready,Ready"
|
|
bitfld.long 0x00 1. " CRC ,CRC Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TOE ,Time Out Error" "No error,Error"
|
|
endif
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "SYSR,System register"
|
|
bitfld.long 0x00 23. " INTEN_IDA ,Illegal Data Access Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " INTEN_IXFR ,Illegal Transfer Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " INTEN_WFUL ,Interrupt Enable for a write transfer to FIFO with full" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " INTEN_REMP ,Interrupt Enable for a read transfer from FIFO with empty" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17. " INTEN_HRESP_ERR ,Interrupt Enable for hresponse error" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 16. " EDMA_EN ,Embedded DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 15. " DAM ,DMA Access Mode" "Dual,Not supported"
|
|
textline " "
|
|
bitfld.long 0x00 14. " DRM ,DMA Request Mode" "Level,Edge"
|
|
bitfld.long 0x00 13. " DRQSL ,DRQ Select" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " REI ,Rise Edge Input" "Falling,Rising"
|
|
bitfld.long 0x00 11. " REO ,Rise Edge Output" "Falling,Rising"
|
|
textline " "
|
|
bitfld.long 0x00 8.--10. " BSY ,Busy Count" "Disabled,1,2,3,4,5,6,7"
|
|
bitfld.long 0x00 7. " RST ,Sync Reset" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " SRAC ,Serial Access Mode" "Parallel,Serial"
|
|
bitfld.long 0x00 5. " INTEN ,Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " NOCRC ,No CRC" "No,Yes"
|
|
bitfld.long 0x00 3. " INTCLR ,INT Clear" "No effect,Clear"
|
|
textline " "
|
|
bitfld.long 0x00 2. " MSIEN ,MS/Pro Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " FCLR ,FIFO Clear" "No effect,Clear"
|
|
textline " "
|
|
bitfld.long 0x00 0. " FDIR ,FIFO Direction" "Receive,Transmit"
|
|
group.long 0x20++0x3
|
|
line.long 0x00 "DSAR,Embedded DMA start address register"
|
|
hexmask.long 0x00 2.--31. 0x4 " EDMA_START_ADRS ,Embedded DMA Start Address"
|
|
width 0xb
|
|
tree.end
|
|
tree "PWM (Pulse-Width Modulator)"
|
|
base ad:0x53FE0000
|
|
width 8.
|
|
group.long 0x00--0x13
|
|
line.long 0x00 "PWMCR,PWM Control Register"
|
|
bitfld.long 0x00 26.--27. " FWM ,FIFO Water Mark" "More or equal to 1,More or equal to 2,More or equal to 3,More or equal to 4"
|
|
bitfld.long 0x00 25. " STOPEN ,Stop Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " DOZEN ,Doze Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 23. " WAITEN ,Wait Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 22. " DBGEN ,Debug Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 21. " BCTR ,Byte Data Swap Control" "Normal,Reversed"
|
|
textline " "
|
|
bitfld.long 0x00 20. " HCTR ,Half-Word Data Swap Control" "Not swapped,Swapped"
|
|
bitfld.long 0x00 18.--19. " POUTC ,PWM Output Configuration" "Output set,Output cleared,Disconnected,Disconnected"
|
|
textline " "
|
|
bitfld.long 0x00 16.--17. " CLKSRC ,Select Clock Source" "Disabled,ipg_clk,ipg_clk_highfreq,ipg_clk_32k"
|
|
hexmask.long.word 0x00 4.--15. 1. 1. " PRESCALER ,Counter Clock Prescaler Value"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SWR ,Software Reset" "No reset,Reset"
|
|
bitfld.long 0x00 1.--2. " REPEAT ,Sample Repeat" "Once,Twice,Four times,Eight times"
|
|
textline " "
|
|
bitfld.long 0x00 0. " EN ,PWM Enable" "Disabled,Enabled"
|
|
line.long 0x04 "PWMSR,PWM Status Register"
|
|
eventfld.long 0x04 6. " FWE ,FIFO Write Error Status" "No error,Error"
|
|
eventfld.long 0x04 5. " CMP ,Compare Status" "Not occurred,Occurred"
|
|
eventfld.long 0x04 4. " ROV ,Roll-Over Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x04 3. " FE ,FIFO Empty Status Bit" "Above,Below"
|
|
bitfld.long 0x04 0.--2. " FIFOAV ,FIFO Available" "Not available,1 word,2 words,3 words,4 words,?..."
|
|
line.long 0x08 "PWMIR,PWM Interrupt Register"
|
|
bitfld.long 0x08 2. " CIE ,Compare Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 1. " RIE ,Roll-Over Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " FIE ,FIFO Empty Interrupt Enable" "Disabled,Enabled"
|
|
line.long 0x0c "PWMSAR,PWM Sample Register"
|
|
hexmask.long.word 0x0c 0.--15. 1. " SAMPLE ,Sample Value"
|
|
line.long 0x10 "PWMPR,PWM Period Register"
|
|
hexmask.long.word 0x10 0.--15. 1. " PERIOD ,Period Value"
|
|
rgroup.long 0x14++0x03
|
|
line.long 0x00 "PWMCNR,PWM Counter Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " COUNT ,Counter Value"
|
|
width 0xb
|
|
tree.end
|
|
tree.open "UART (Universal Asynchronous Receiver/Transmitter)"
|
|
tree "UART1"
|
|
base ad:0x43f90000
|
|
width 7.
|
|
hgroup.long 0x00++0x3
|
|
hide.long 0x00 "URXD,UART Receiver Register"
|
|
in
|
|
if (((data.long(asd:0x43f90000+0x84))&0x20)==0x20)
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " TX_DATA ,Transmit Data"
|
|
else
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--6. 1. " TX_DATA ,Transmit Data"
|
|
endif
|
|
group.long 0x80++0x3
|
|
line.long 0x00 "UCR1,UART Control Register 1"
|
|
bitfld.long 0x00 15. " ADEN ,Automatic Baud Rate Detection Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " ADBR ,Automatic Detection of Baud Rate" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TRDYEN ,Transmitter Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " IDEN ,Idle Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10.--11. " ICD ,Idle Condition Detect" "4 frames,8 frames,16 frames,32 frames"
|
|
bitfld.long 0x00 9. " RRDYEN ,Receiver Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RXDMAEN ,Receive Ready DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " IREN ,Infrared Interface Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " TXMPTYEN ,Transmitter Empty Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RTSDEN ,RTS Delta Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " SNDBRK ,Send BREAK" "Not sent,Sent"
|
|
bitfld.long 0x00 3. " TXDMAEN ,Transmitter Ready DMA Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ATDMAEN ,Aging DMA Timer Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " DOZE ,DOZE" "UART enabled,UART disabled"
|
|
bitfld.long 0x00 0. " UARTEN ,UART Enable" "Disabled,Enabled"
|
|
group.long 0x84++0x3
|
|
line.long 0x00 "UCR2,UART Control Register 2"
|
|
bitfld.long 0x00 15. " ESCI ,Escape Sequence Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " IRTS ,Ignore RTS Pin" "Not ignored,Ignored"
|
|
bitfld.long 0x00 13. " CTSC ,CTS Pin Control" "CTS,Receiver"
|
|
textline " "
|
|
bitfld.long 0x00 12. " CTS ,Clear to Send" "High,Low"
|
|
bitfld.long 0x00 11. " ESCEN ,Escape Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 9.--10. " RTEC ,Request to Send Edge Control" "Rising,Falling,Any,Any"
|
|
textline " "
|
|
bitfld.long 0x00 8. " PREN ,Parity Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " PROE ,Parity Odd/Even" "Even,Odd"
|
|
bitfld.long 0x00 6. " STPB ,Stop" "1 bit,2 bits"
|
|
textline " "
|
|
bitfld.long 0x00 5. " WS ,Word Size" "7-bit,8-bit"
|
|
bitfld.long 0x00 4. " RTSEN ,Request to Send Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " ATEN ,Aging Timer Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TXEN ,Transmitter Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " RXEN ,Receiver Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " SRST ,Software Reset" "Reset,No reset"
|
|
if (((d.l(asd:(0x43f90000+0x90)))&0x40)==0x0)
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,Data Carrier Detect" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,Ring Indicator" "Low,High"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
else
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,DCDDELT Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,RIDELT Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
endif
|
|
group.long 0x8c++0x3
|
|
line.long 0x00 "UCR4,UART Control Register 4"
|
|
bitfld.long 0x00 10.--15. " CTSTL ,CTS Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 9. " INVR ,Inverted Infrared Reception" "Active low,Active high"
|
|
bitfld.long 0x00 8. " ENIRI ,Serial Infrared Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " WKEN ,WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " IDDMAEN ,DMA IDLE Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " IRSC ,IR Special Case" "Sampling clock,Reference clock"
|
|
textline " "
|
|
bitfld.long 0x00 4. " LPBYP ,Low Power Bypass" "Enabled,Disabled"
|
|
bitfld.long 0x00 3. " TCEN ,Transmit Complete Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " BKEN ,BREAK Condition Detected Interrupt Enabled" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " OREN ,Receiver Overrun Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " DREN ,Receive Data Ready Interrupt Enable" "Disabled,Enabled"
|
|
group.long 0x90++0x3
|
|
line.long 0x00 "UFCR,UART FIFO Control Register"
|
|
bitfld.long 0x00 10.--15. " TXTL ,Transmitter Trigger Level" "Reserved,Reserved,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 7.--9. " RFDIV ,Reference Frequency Divider" "Div by 6,Div by 5,Div by 4,Div by 3,Div by 2,Div by 1,Div by 7,?..."
|
|
bitfld.long 0x00 6. " DCEDTE ,DCE/DTE Mode Select" "DCE,DTE"
|
|
textline " "
|
|
bitfld.long 0x00 0.--5. " RXTL ,Receiver Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
group.long 0x94++0x3
|
|
line.long 0x00 "USR1,UART Status Register 1"
|
|
eventfld.long 0x00 15. " PARITYERR ,Parity Error Interrupt Flag" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 14. " RTSS ,/RTS Pin Status" "Inactive,Active"
|
|
bitfld.long 0x00 13. " TRDY ,Transmitter Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 12. " RTSD ,RTS Delta" "Not changed,Changed"
|
|
eventfld.long 0x00 11. " ESCF ,Escape Sequence Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 10. " FRAMERR ,Frame Error Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RRDY ,Receiver Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 8. " AGTIM ,Ageing Timer Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " DTRD ,DTR Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RXDS ,Receiver IDLE Interrupt Flag" "In progress,Idle"
|
|
eventfld.long 0x00 5. " AIRINT ,Asynchronous IR WAKE Interrupt Flag" "Not detected,Detected"
|
|
eventfld.long 0x00 4. " AWAKE ,Asynchronous WAKE Interrupt Flag" "Not detected,Detected"
|
|
group.long 0x98++0x3
|
|
line.long 0x00 "USR2,UART Status Register 2"
|
|
eventfld.long 0x00 15. " ADET ,Automatic Baud Rate Detect Complete" "Not received,Received"
|
|
bitfld.long 0x00 14. " TXFE ,Transmit Buffer FIFO Empty" "Not empty,Empty"
|
|
eventfld.long 0x00 13. " DTRF ,DTR Edge Triggered Interrupt Flag" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 12. " IDLE ,Idle Condition" "Not detected,Detected"
|
|
eventfld.long 0x00 11. " ACST ,Autobaud Counter Stopped" "Not finished,Finished"
|
|
eventfld.long 0x00 10. " RIDELT ,Ring Indicator Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RIIN ,Ring Indicator Input" "Detected,Not detected"
|
|
eventfld.long 0x00 8. " IRINT ,Serial Infrared Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " WAKE ,Wake" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 6. " DCDDELT ,Data Carrier Detect Delta" "Not changed,Changed"
|
|
bitfld.long 0x00 5. " DCDIN ,Data Carrier Detect Input" "Detected,Not detected"
|
|
eventfld.long 0x00 4. " RTSF ,RTS Edge Triggered Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 3. " TXDC ,Transmitter Complete" "Not completed,Completed"
|
|
eventfld.long 0x00 2. " BRCD ,BREAK Condition Detected" "Not detected,Detected"
|
|
eventfld.long 0x00 1. " ORE ,Overrun Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 0. " RDR ,Receive Data Ready" "Not ready,Ready"
|
|
group.long 0x9c++0x3
|
|
line.long 0x00 "UESC,UART Escape Character Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ESC_CHAR ,UART Escape Character"
|
|
group.long 0xa0++0x3
|
|
line.long 0x00 "UTIM,UART Escape Timer Register"
|
|
hexmask.long.word 0x00 0.--11. 1. " TIM ,UART Escape Timer"
|
|
group.long 0xa4++0x3
|
|
line.long 0x00 "UBIR,UART BRM Incremental Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " INC ,UART BRM Incremental Register"
|
|
group.long 0xa8++0x3
|
|
line.long 0x00 "UBMR,Modulator Dominator"
|
|
hexmask.long.word 0x00 0.--15. 1. " MOD ,Modulator Dominator"
|
|
rgroup.long 0xac++0x3
|
|
line.long 0x00 "UBRC,UART Baud Rate Count Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " BCNT ,UART Baud Rate Count Register"
|
|
group.long 0xb0++0x3
|
|
line.long 0x00 "ONEMS,UART One Millisecond Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " ONEMS ,UART One Millisecond Register"
|
|
group.long 0xb4++0x3
|
|
line.long 0x00 "UTS,UART Test Register"
|
|
bitfld.long 0x00 13. " FRCPERR ,Force Parity Error" "Not forced,Forced"
|
|
bitfld.long 0x00 12. " LOOP ,Loop TX and RX for Test" "Normal,Loop"
|
|
bitfld.long 0x00 11. " DBGEN ,/debug_enable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 10. " LOOPIR ,Loop Tx and RX for IR Test" "Normal,Loop"
|
|
bitfld.long 0x00 9. " RXDBG ,RX_fifo_debug_mode" "Not incremented,Incremented"
|
|
bitfld.long 0x00 6. " TXEMPTY ,Tx FIFO Empty" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RXEMPTY ,Rx FIFO Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 4. " TXFULL ,Tx FIFO Full" "Not full,Full"
|
|
bitfld.long 0x00 3. " RXFULL ,Rx FIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SOFTRST ,Software Reset" "No reset,Reset"
|
|
width 0xb
|
|
tree.end
|
|
tree "UART2"
|
|
base ad:0x43f94000
|
|
width 7.
|
|
hgroup.long 0x00++0x3
|
|
hide.long 0x00 "URXD,UART Receiver Register"
|
|
in
|
|
if (((data.long(asd:0x43f94000+0x84))&0x20)==0x20)
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " TX_DATA ,Transmit Data"
|
|
else
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--6. 1. " TX_DATA ,Transmit Data"
|
|
endif
|
|
group.long 0x80++0x3
|
|
line.long 0x00 "UCR1,UART Control Register 1"
|
|
bitfld.long 0x00 15. " ADEN ,Automatic Baud Rate Detection Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " ADBR ,Automatic Detection of Baud Rate" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TRDYEN ,Transmitter Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " IDEN ,Idle Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10.--11. " ICD ,Idle Condition Detect" "4 frames,8 frames,16 frames,32 frames"
|
|
bitfld.long 0x00 9. " RRDYEN ,Receiver Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RXDMAEN ,Receive Ready DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " IREN ,Infrared Interface Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " TXMPTYEN ,Transmitter Empty Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RTSDEN ,RTS Delta Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " SNDBRK ,Send BREAK" "Not sent,Sent"
|
|
bitfld.long 0x00 3. " TXDMAEN ,Transmitter Ready DMA Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ATDMAEN ,Aging DMA Timer Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " DOZE ,DOZE" "UART enabled,UART disabled"
|
|
bitfld.long 0x00 0. " UARTEN ,UART Enable" "Disabled,Enabled"
|
|
group.long 0x84++0x3
|
|
line.long 0x00 "UCR2,UART Control Register 2"
|
|
bitfld.long 0x00 15. " ESCI ,Escape Sequence Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " IRTS ,Ignore RTS Pin" "Not ignored,Ignored"
|
|
bitfld.long 0x00 13. " CTSC ,CTS Pin Control" "CTS,Receiver"
|
|
textline " "
|
|
bitfld.long 0x00 12. " CTS ,Clear to Send" "High,Low"
|
|
bitfld.long 0x00 11. " ESCEN ,Escape Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 9.--10. " RTEC ,Request to Send Edge Control" "Rising,Falling,Any,Any"
|
|
textline " "
|
|
bitfld.long 0x00 8. " PREN ,Parity Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " PROE ,Parity Odd/Even" "Even,Odd"
|
|
bitfld.long 0x00 6. " STPB ,Stop" "1 bit,2 bits"
|
|
textline " "
|
|
bitfld.long 0x00 5. " WS ,Word Size" "7-bit,8-bit"
|
|
bitfld.long 0x00 4. " RTSEN ,Request to Send Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " ATEN ,Aging Timer Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TXEN ,Transmitter Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " RXEN ,Receiver Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " SRST ,Software Reset" "Reset,No reset"
|
|
if (((d.l(asd:(0x43f94000+0x90)))&0x40)==0x0)
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,Data Carrier Detect" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,Ring Indicator" "Low,High"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
else
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,DCDDELT Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,RIDELT Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
endif
|
|
group.long 0x8c++0x3
|
|
line.long 0x00 "UCR4,UART Control Register 4"
|
|
bitfld.long 0x00 10.--15. " CTSTL ,CTS Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 9. " INVR ,Inverted Infrared Reception" "Active low,Active high"
|
|
bitfld.long 0x00 8. " ENIRI ,Serial Infrared Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " WKEN ,WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " IDDMAEN ,DMA IDLE Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " IRSC ,IR Special Case" "Sampling clock,Reference clock"
|
|
textline " "
|
|
bitfld.long 0x00 4. " LPBYP ,Low Power Bypass" "Enabled,Disabled"
|
|
bitfld.long 0x00 3. " TCEN ,Transmit Complete Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " BKEN ,BREAK Condition Detected Interrupt Enabled" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " OREN ,Receiver Overrun Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " DREN ,Receive Data Ready Interrupt Enable" "Disabled,Enabled"
|
|
group.long 0x90++0x3
|
|
line.long 0x00 "UFCR,UART FIFO Control Register"
|
|
bitfld.long 0x00 10.--15. " TXTL ,Transmitter Trigger Level" "Reserved,Reserved,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 7.--9. " RFDIV ,Reference Frequency Divider" "Div by 6,Div by 5,Div by 4,Div by 3,Div by 2,Div by 1,Div by 7,?..."
|
|
bitfld.long 0x00 6. " DCEDTE ,DCE/DTE Mode Select" "DCE,DTE"
|
|
textline " "
|
|
bitfld.long 0x00 0.--5. " RXTL ,Receiver Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
group.long 0x94++0x3
|
|
line.long 0x00 "USR1,UART Status Register 1"
|
|
eventfld.long 0x00 15. " PARITYERR ,Parity Error Interrupt Flag" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 14. " RTSS ,/RTS Pin Status" "Inactive,Active"
|
|
bitfld.long 0x00 13. " TRDY ,Transmitter Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 12. " RTSD ,RTS Delta" "Not changed,Changed"
|
|
eventfld.long 0x00 11. " ESCF ,Escape Sequence Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 10. " FRAMERR ,Frame Error Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RRDY ,Receiver Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 8. " AGTIM ,Ageing Timer Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " DTRD ,DTR Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RXDS ,Receiver IDLE Interrupt Flag" "In progress,Idle"
|
|
eventfld.long 0x00 5. " AIRINT ,Asynchronous IR WAKE Interrupt Flag" "Not detected,Detected"
|
|
eventfld.long 0x00 4. " AWAKE ,Asynchronous WAKE Interrupt Flag" "Not detected,Detected"
|
|
group.long 0x98++0x3
|
|
line.long 0x00 "USR2,UART Status Register 2"
|
|
eventfld.long 0x00 15. " ADET ,Automatic Baud Rate Detect Complete" "Not received,Received"
|
|
bitfld.long 0x00 14. " TXFE ,Transmit Buffer FIFO Empty" "Not empty,Empty"
|
|
eventfld.long 0x00 13. " DTRF ,DTR Edge Triggered Interrupt Flag" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 12. " IDLE ,Idle Condition" "Not detected,Detected"
|
|
eventfld.long 0x00 11. " ACST ,Autobaud Counter Stopped" "Not finished,Finished"
|
|
eventfld.long 0x00 10. " RIDELT ,Ring Indicator Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RIIN ,Ring Indicator Input" "Detected,Not detected"
|
|
eventfld.long 0x00 8. " IRINT ,Serial Infrared Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " WAKE ,Wake" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 6. " DCDDELT ,Data Carrier Detect Delta" "Not changed,Changed"
|
|
bitfld.long 0x00 5. " DCDIN ,Data Carrier Detect Input" "Detected,Not detected"
|
|
eventfld.long 0x00 4. " RTSF ,RTS Edge Triggered Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 3. " TXDC ,Transmitter Complete" "Not completed,Completed"
|
|
eventfld.long 0x00 2. " BRCD ,BREAK Condition Detected" "Not detected,Detected"
|
|
eventfld.long 0x00 1. " ORE ,Overrun Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 0. " RDR ,Receive Data Ready" "Not ready,Ready"
|
|
group.long 0x9c++0x3
|
|
line.long 0x00 "UESC,UART Escape Character Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ESC_CHAR ,UART Escape Character"
|
|
group.long 0xa0++0x3
|
|
line.long 0x00 "UTIM,UART Escape Timer Register"
|
|
hexmask.long.word 0x00 0.--11. 1. " TIM ,UART Escape Timer"
|
|
group.long 0xa4++0x3
|
|
line.long 0x00 "UBIR,UART BRM Incremental Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " INC ,UART BRM Incremental Register"
|
|
group.long 0xa8++0x3
|
|
line.long 0x00 "UBMR,Modulator Dominator"
|
|
hexmask.long.word 0x00 0.--15. 1. " MOD ,Modulator Dominator"
|
|
rgroup.long 0xac++0x3
|
|
line.long 0x00 "UBRC,UART Baud Rate Count Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " BCNT ,UART Baud Rate Count Register"
|
|
group.long 0xb0++0x3
|
|
line.long 0x00 "ONEMS,UART One Millisecond Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " ONEMS ,UART One Millisecond Register"
|
|
group.long 0xb4++0x3
|
|
line.long 0x00 "UTS,UART Test Register"
|
|
bitfld.long 0x00 13. " FRCPERR ,Force Parity Error" "Not forced,Forced"
|
|
bitfld.long 0x00 12. " LOOP ,Loop TX and RX for Test" "Normal,Loop"
|
|
bitfld.long 0x00 11. " DBGEN ,/debug_enable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 10. " LOOPIR ,Loop Tx and RX for IR Test" "Normal,Loop"
|
|
bitfld.long 0x00 9. " RXDBG ,RX_fifo_debug_mode" "Not incremented,Incremented"
|
|
bitfld.long 0x00 6. " TXEMPTY ,Tx FIFO Empty" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RXEMPTY ,Rx FIFO Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 4. " TXFULL ,Tx FIFO Full" "Not full,Full"
|
|
bitfld.long 0x00 3. " RXFULL ,Rx FIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SOFTRST ,Software Reset" "No reset,Reset"
|
|
width 0xb
|
|
tree.end
|
|
tree "UART3"
|
|
base ad:0x5000c000
|
|
width 7.
|
|
hgroup.long 0x00++0x3
|
|
hide.long 0x00 "URXD,UART Receiver Register"
|
|
in
|
|
if (((data.long(asd:0x5000c000+0x84))&0x20)==0x20)
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " TX_DATA ,Transmit Data"
|
|
else
|
|
wgroup.long 0x40++0x3
|
|
line.long 0x00 "UTXD,UART Transmitter Register"
|
|
hexmask.long.byte 0x00 0.--6. 1. " TX_DATA ,Transmit Data"
|
|
endif
|
|
group.long 0x80++0x3
|
|
line.long 0x00 "UCR1,UART Control Register 1"
|
|
bitfld.long 0x00 15. " ADEN ,Automatic Baud Rate Detection Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " ADBR ,Automatic Detection of Baud Rate" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TRDYEN ,Transmitter Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " IDEN ,Idle Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10.--11. " ICD ,Idle Condition Detect" "4 frames,8 frames,16 frames,32 frames"
|
|
bitfld.long 0x00 9. " RRDYEN ,Receiver Ready Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RXDMAEN ,Receive Ready DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " IREN ,Infrared Interface Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " TXMPTYEN ,Transmitter Empty Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RTSDEN ,RTS Delta Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " SNDBRK ,Send BREAK" "Not sent,Sent"
|
|
bitfld.long 0x00 3. " TXDMAEN ,Transmitter Ready DMA Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ATDMAEN ,Aging DMA Timer Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " DOZE ,DOZE" "UART enabled,UART disabled"
|
|
bitfld.long 0x00 0. " UARTEN ,UART Enable" "Disabled,Enabled"
|
|
group.long 0x84++0x3
|
|
line.long 0x00 "UCR2,UART Control Register 2"
|
|
bitfld.long 0x00 15. " ESCI ,Escape Sequence Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " IRTS ,Ignore RTS Pin" "Not ignored,Ignored"
|
|
bitfld.long 0x00 13. " CTSC ,CTS Pin Control" "CTS,Receiver"
|
|
textline " "
|
|
bitfld.long 0x00 12. " CTS ,Clear to Send" "High,Low"
|
|
bitfld.long 0x00 11. " ESCEN ,Escape Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 9.--10. " RTEC ,Request to Send Edge Control" "Rising,Falling,Any,Any"
|
|
textline " "
|
|
bitfld.long 0x00 8. " PREN ,Parity Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " PROE ,Parity Odd/Even" "Even,Odd"
|
|
bitfld.long 0x00 6. " STPB ,Stop" "1 bit,2 bits"
|
|
textline " "
|
|
bitfld.long 0x00 5. " WS ,Word Size" "7-bit,8-bit"
|
|
bitfld.long 0x00 4. " RTSEN ,Request to Send Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " ATEN ,Aging Timer Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TXEN ,Transmitter Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " RXEN ,Receiver Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " SRST ,Software Reset" "Reset,No reset"
|
|
if (((d.l(asd:(0x5000c000+0x90)))&0x40)==0x0)
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,Data Carrier Detect" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,Ring Indicator" "Low,High"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
else
|
|
group.long 0x88++0x3
|
|
line.long 0x00 "UCR3,UART Control Register 3"
|
|
bitfld.long 0x00 14.--15. " DPEC ,DTR/DSR Interrupt Edge Control" "Rising,Falling,Either,Either"
|
|
bitfld.long 0x00 13. " DTREN ,Data Terminal Ready Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PARERREN ,Parity Error Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " FRAERREN ,Frame Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " DSR ,Data Set Ready" "Low,High"
|
|
bitfld.long 0x00 9. " DCD ,DCDDELT Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8. " RI ,RIDELT Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " ADNIMP ,Autoband Detection Not improved" "New,Old"
|
|
bitfld.long 0x00 6. " RXDSEN ,Receive Status Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AIRINTEN ,Asynchronous IR WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " AWAKEN ,Asynchronous WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " DTRDEN ,Data Terminal Ready Delta Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RXDMUXSEL ,RXD Muxed Input Selected" "Not muxed,Muxed"
|
|
bitfld.long 0x00 1. " INVT ,Inverted Infrared Transmission" "Active low,Active high"
|
|
bitfld.long 0x00 0. " ACIEN ,Autobaud Counter Interrupt Enable" "Disabled,Enabled"
|
|
endif
|
|
group.long 0x8c++0x3
|
|
line.long 0x00 "UCR4,UART Control Register 4"
|
|
bitfld.long 0x00 10.--15. " CTSTL ,CTS Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 9. " INVR ,Inverted Infrared Reception" "Active low,Active high"
|
|
bitfld.long 0x00 8. " ENIRI ,Serial Infrared Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " WKEN ,WAKE Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " IDDMAEN ,DMA IDLE Condition Detected Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " IRSC ,IR Special Case" "Sampling clock,Reference clock"
|
|
textline " "
|
|
bitfld.long 0x00 4. " LPBYP ,Low Power Bypass" "Enabled,Disabled"
|
|
bitfld.long 0x00 3. " TCEN ,Transmit Complete Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " BKEN ,BREAK Condition Detected Interrupt Enabled" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " OREN ,Receiver Overrun Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " DREN ,Receive Data Ready Interrupt Enable" "Disabled,Enabled"
|
|
group.long 0x90++0x3
|
|
line.long 0x00 "UFCR,UART FIFO Control Register"
|
|
bitfld.long 0x00 10.--15. " TXTL ,Transmitter Trigger Level" "Reserved,Reserved,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
bitfld.long 0x00 7.--9. " RFDIV ,Reference Frequency Divider" "Div by 6,Div by 5,Div by 4,Div by 3,Div by 2,Div by 1,Div by 7,?..."
|
|
bitfld.long 0x00 6. " DCEDTE ,DCE/DTE Mode Select" "DCE,DTE"
|
|
textline " "
|
|
bitfld.long 0x00 0.--5. " RXTL ,Receiver Trigger Level" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,?..."
|
|
group.long 0x94++0x3
|
|
line.long 0x00 "USR1,UART Status Register 1"
|
|
eventfld.long 0x00 15. " PARITYERR ,Parity Error Interrupt Flag" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 14. " RTSS ,/RTS Pin Status" "Inactive,Active"
|
|
bitfld.long 0x00 13. " TRDY ,Transmitter Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 12. " RTSD ,RTS Delta" "Not changed,Changed"
|
|
eventfld.long 0x00 11. " ESCF ,Escape Sequence Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 10. " FRAMERR ,Frame Error Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RRDY ,Receiver Ready Interrupt / DMA Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 8. " AGTIM ,Ageing Timer Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " DTRD ,DTR Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RXDS ,Receiver IDLE Interrupt Flag" "In progress,Idle"
|
|
eventfld.long 0x00 5. " AIRINT ,Asynchronous IR WAKE Interrupt Flag" "Not detected,Detected"
|
|
eventfld.long 0x00 4. " AWAKE ,Asynchronous WAKE Interrupt Flag" "Not detected,Detected"
|
|
group.long 0x98++0x3
|
|
line.long 0x00 "USR2,UART Status Register 2"
|
|
eventfld.long 0x00 15. " ADET ,Automatic Baud Rate Detect Complete" "Not received,Received"
|
|
bitfld.long 0x00 14. " TXFE ,Transmit Buffer FIFO Empty" "Not empty,Empty"
|
|
eventfld.long 0x00 13. " DTRF ,DTR Edge Triggered Interrupt Flag" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 12. " IDLE ,Idle Condition" "Not detected,Detected"
|
|
eventfld.long 0x00 11. " ACST ,Autobaud Counter Stopped" "Not finished,Finished"
|
|
eventfld.long 0x00 10. " RIDELT ,Ring Indicator Delta" "Not changed,Changed"
|
|
textline " "
|
|
bitfld.long 0x00 9. " RIIN ,Ring Indicator Input" "Detected,Not detected"
|
|
eventfld.long 0x00 8. " IRINT ,Serial Infrared Interrupt Flag" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 7. " WAKE ,Wake" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x00 6. " DCDDELT ,Data Carrier Detect Delta" "Not changed,Changed"
|
|
bitfld.long 0x00 5. " DCDIN ,Data Carrier Detect Input" "Detected,Not detected"
|
|
eventfld.long 0x00 4. " RTSF ,RTS Edge Triggered Interrupt Flag" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 3. " TXDC ,Transmitter Complete" "Not completed,Completed"
|
|
eventfld.long 0x00 2. " BRCD ,BREAK Condition Detected" "Not detected,Detected"
|
|
eventfld.long 0x00 1. " ORE ,Overrun Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 0. " RDR ,Receive Data Ready" "Not ready,Ready"
|
|
group.long 0x9c++0x3
|
|
line.long 0x00 "UESC,UART Escape Character Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ESC_CHAR ,UART Escape Character"
|
|
group.long 0xa0++0x3
|
|
line.long 0x00 "UTIM,UART Escape Timer Register"
|
|
hexmask.long.word 0x00 0.--11. 1. " TIM ,UART Escape Timer"
|
|
group.long 0xa4++0x3
|
|
line.long 0x00 "UBIR,UART BRM Incremental Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " INC ,UART BRM Incremental Register"
|
|
group.long 0xa8++0x3
|
|
line.long 0x00 "UBMR,Modulator Dominator"
|
|
hexmask.long.word 0x00 0.--15. 1. " MOD ,Modulator Dominator"
|
|
rgroup.long 0xac++0x3
|
|
line.long 0x00 "UBRC,UART Baud Rate Count Register"
|
|
hexmask.long.word 0x00 0.--15. 1. " BCNT ,UART Baud Rate Count Register"
|
|
group.long 0xb0++0x3
|
|
line.long 0x00 "ONEMS,UART One Millisecond Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " ONEMS ,UART One Millisecond Register"
|
|
group.long 0xb4++0x3
|
|
line.long 0x00 "UTS,UART Test Register"
|
|
bitfld.long 0x00 13. " FRCPERR ,Force Parity Error" "Not forced,Forced"
|
|
bitfld.long 0x00 12. " LOOP ,Loop TX and RX for Test" "Normal,Loop"
|
|
bitfld.long 0x00 11. " DBGEN ,/debug_enable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 10. " LOOPIR ,Loop Tx and RX for IR Test" "Normal,Loop"
|
|
bitfld.long 0x00 9. " RXDBG ,RX_fifo_debug_mode" "Not incremented,Incremented"
|
|
bitfld.long 0x00 6. " TXEMPTY ,Tx FIFO Empty" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RXEMPTY ,Rx FIFO Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 4. " TXFULL ,Tx FIFO Full" "Not full,Full"
|
|
bitfld.long 0x00 3. " RXFULL ,Rx FIFO Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SOFTRST ,Software Reset" "No reset,Reset"
|
|
width 0xb
|
|
tree.end
|
|
tree.end
|
|
tree.open "USBOH (Universal Serial Bus OTG HOST)"
|
|
base ad:0x53FF4000
|
|
width 19.
|
|
tree "Common Registers"
|
|
group.long 0x600++0x13
|
|
line.long 0x00 "USB_CTRL,USB Control Register"
|
|
bitfld.long 0x00 31. " OWIR ,OTG Wake up Interrupt Request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 29.--30. " OSIC ,OTG Serial Interface Configuration" "Differential/Unidirectional,Differential/Bidirectional,Single Ended/Unidirectional,Single Ended/Bidirectional"
|
|
textline " "
|
|
bitfld.long 0x00 28. " OUIE ,OTG ULPI Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 27. " OWIE ,OTG Wake-up Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 26. " HEX_TEN ,Host external ULPI clock enable" "Internal,External"
|
|
bitfld.long 0x00 25. " OEX_TEN ,OTG external ULPI clock enable" "Internal,External"
|
|
textline " "
|
|
bitfld.long 0x00 24. " OPM ,OTG Power Mask" "Not masked,Masked"
|
|
bitfld.long 0x00 23. " HWIR ,Host Wake-up Interrupt Request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 21.--22. " HSIC ,Host Serial Interface Configuration" "Differential/Unidirectional,Differential/Bidirectional,Single Ended/Unidirectional,Single Ended/Bidirectional"
|
|
textline " "
|
|
bitfld.long 0x00 20. " HUIE ,Host ULPI Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " HWIE ,Host Wake-up Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " PP_HST ,Power polarity for Host" "Low,High"
|
|
bitfld.long 0x00 17. " OV_EN ,AHB override enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 16. " HPM ,Host Power Mask" "Not masked,Masked"
|
|
bitfld.long 0x00 15. " VBUS_WKEN ,OTG VBUS wakeup enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 14. " ID_WKEN ,OTG ID wakeup enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " OLKEN ,OTG AHB lock enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " HLKEN ,Host AHB lock enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 11. " PP_OTG ,Power polarity" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 10. " XCSO ,Xcvr Clock Select for OTG port to use internal 60Mhz" "Not forced,Forced"
|
|
bitfld.long 0x00 9. " XCSH ,Xcvr Clock Select for Host port to use the internal 60 Mhz" "Not forced,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 8. " IP_PUIDP ,Controls Ipp_Puimpel_Pullup_Dp signal" "Not forced,Forced"
|
|
bitfld.long 0x00 7. " IP_PUE_UP ,Controls ipp_pue_pullup_dp signal" "Not forced,Forced"
|
|
textline " "
|
|
bitfld.long 0x00 6. " IP_PUE_DWN ,Controls ipp_pue_pulldwn_dpdm signal" "Not forced,Forced"
|
|
bitfld.long 0x00 5. " HSDT ,Host Serial TLL Disable" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 4. " USBTE ,USBT Transciever enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " OCPOL_OTG ,OverCurrent Polarity" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x00 2. " OCPOL_HST ,OverCurrent Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " HOCS ,Host OverCurrent State" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x00 0. " OOCS ,OTG OverCurrent State" "Not occurred,Occurred"
|
|
width 19.
|
|
line.long 0x04 "USB_OTG_MIRROR,OTG Port Mirror Register"
|
|
bitfld.long 0x04 8. " OUTMICLK ,OTG UTMI PHY Clock on detection" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 7. " OULPICLK ,OTG ULPI PHY Clock on detection" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 6. " HULPICLK ,HOST ULPI fPHY Clock on detection" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 4. " SESEND ,B Device Session End" "Active,End"
|
|
textline " "
|
|
bitfld.long 0x04 3. " VBUSVAL ,Vbus Valid" "Invalid,Valid"
|
|
textline " "
|
|
bitfld.long 0x04 2. " BSESVLD ,B Session Valid" "Not valid,Valid"
|
|
textline " "
|
|
bitfld.long 0x04 1. " ASESVLD ,A Session Valid" "Not valid,Valid"
|
|
textline " "
|
|
bitfld.long 0x04 0. " IDDIG ,OTG ID-pin Status" "Low(A-device),High(B-device)"
|
|
line.long 0x08 "USB_PHY_CTRL_FUNC, OTG UTMI PHY Function Control Register"
|
|
bitfld.long 0x08 27. " CLKVLD ,Clk from the PHY is within the spec" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x08 26. " SUSP ,Software suspend to the PHY" "Suspended,Not suspended"
|
|
textline " "
|
|
bitfld.long 0x08 25. " RESET ,Software reset to the PHY" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x08 24. " USBEN ,Enables the USB UTMI PHY" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 23. " EVDO ,Enables off chip resistor divider for vbus" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 22. " LSFE ,Enables filtering of LineState to account for skew between D+/D- signals" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 20. " VCTL_LD ,Enables signal to load the Vendor Control Reg from the VControl pins" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 16.--19. " VCTL_ADDR ,Vendor defined control used to address the Vendor control registers" "0.,1.,2.,3.,4.,5.,6.,7.,8.,9.,10.,11.,12.,13.,14.,15."
|
|
textline " "
|
|
hexmask.long.byte 0x08 8.--15. 1. " VCTL_DATA ,Output data to be written into the Vendor Control Reg"
|
|
textline " "
|
|
hexmask.long.byte 0x08 0.--7. 1. " VSTS ,Data present at the Vendor Control register"
|
|
line.long 0x0C "USB_PHY_CTRL_TEST, USB PHY Test Register"
|
|
bitfld.long 0x0C 3.--4. " TM ,utmi test mode" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " LB ,Enables the PHY to receive its own packeds" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 1. " NFC ,Disregards the UTMI spec for clock accuracy" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x0C 0. " FT ,Enables PHY to use the ipt_scan_clk instead of the internally generated PLL clocks" "Disabled,Enabled"
|
|
tree.end
|
|
width 18.
|
|
tree "OTG USB"
|
|
rgroup.long 0x00++0x17
|
|
line.long 0x00 "UOG_ID,Identification Register"
|
|
hexmask.long.byte 0x00 16.--23. 1. " REVISION ,Revision Number of the Core"
|
|
hexmask.long.byte 0x00 8.--13. 1. " NID ,Ones complement version of ID"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--5. 1. " ID ,Configuration Number"
|
|
line.long 0x04 "UOG_HWGENERAL,General Hardware Register"
|
|
bitfld.long 0x04 9. " SM ,VUSB_HS_PHY_SERIAL" "0,1"
|
|
bitfld.long 0x04 6.--8. " PHYM ,VUSB_HS_PHY_TYPE" "000,001,010,011,100,101,110,111"
|
|
textline " "
|
|
bitfld.long 0x04 4.--5. " PHYW ,VUSB_HS_PHY16_8" "00,01,10,11"
|
|
bitfld.long 0x04 3. " BWT ,Reserved for Internal Testing" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 1.--2. " CLKC ,VUSB_HS_CLOCK_CONFIGURATION" "00,01,10,11"
|
|
bitfld.long 0x04 0. " RT ,VUSB_HS_RESET_TYPE" "0,1"
|
|
line.long 0x08 "UOG_HWHOST,Host Hardware Parameters Register"
|
|
hexmask.long.byte 0x08 24.--31. 1. " TTPER ,VUSB_HS_TT_PERIODIC_CONTEXTS"
|
|
hexmask.long.byte 0x08 16.--23. 1. " TTASY ,VUSB_HS_TT_ASYNC_CONTEXTS"
|
|
textline " "
|
|
bitfld.long 0x08 1.--3. " NPORT ,VUSB_HS_NUM_PORT-1" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x08 0. " HC ,VUSB_HS_HOST" "0,1"
|
|
line.long 0x0c "UOG_HWDEVICE,Device Hardware Parameters Register"
|
|
hexmask.long.byte 0x0c 1.--5. 1. " DEVEP ,VUSB_HS_DEV_EP"
|
|
bitfld.long 0x0c 0. " DC ,VUSB_HS_DEV" "0,1"
|
|
line.long 0x10 "UOG_HWTXBUF,TX Buffer Hardware Parameters Register"
|
|
bitfld.long 0x10 31. " TXLCR ,VUSB_HS_TX_LOCAL_CONTEXT_REGISTERS" "0,1"
|
|
hexmask.long.byte 0x10 16.--23. 1. " TXCHANADD ,VUSB_HS_TX_CHAN_ADD"
|
|
textline " "
|
|
hexmask.long.byte 0x10 8.--15. 1. " TXADD ,VUSB_HS_TX_ADD"
|
|
hexmask.long.byte 0x10 0.--7. 1. " TCBURST ,VUSB_HS_TX_BURST"
|
|
line.long 0x14 "UOG_HWRXBUF,RX Buffer Hardware Parameters Register"
|
|
hexmask.long.byte 0x14 8.--15. 1. " RXADD ,VUSB_HS_RX_ADD"
|
|
hexmask.long.byte 0x14 0.--7. 1. " RXBURST ,VUSB_HS_RX_BURST"
|
|
rgroup.byte 0x100++0x00
|
|
line.byte 0x00 "UOG_CAPLENGTH,EHCI Compliant Register"
|
|
hexmask.byte 0x00 0.--7. 1. " CAPLENGTH ,Capability Length"
|
|
rgroup.word 0x102++0x01
|
|
line.word 0x00 "UOG_HCIVERSION,EHCI Compliant Register"
|
|
hexmask.word 0x00 0.--15. 1. " HCIVERSION ,Host Interface Version Number"
|
|
rgroup.long 0x104++0x07
|
|
line.long 0x00 "UOG_HCSPARAMS,EHCI Compliant With Extensions Register"
|
|
bitfld.long 0x00 24.--27. " N_TT ,Number of Transaction Translators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 20.--23. " N_PTT ,Number of Ports per Transaction Translator" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PI ,Port Indicators" "0,1"
|
|
bitfld.long 0x00 12.--15. " N_CC ,Number of Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 8.--11. " N_PCC ,Number of Ports per Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 4. " PPC ,Port Power Control" "Not included,Included"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " N_PORTS ,Number of Downstream Ports" "Reserved,1,2,3,4,5,6,7,8,?..."
|
|
line.long 0x04 "UOG_HCCPARAMS,EHCI Compliant Register"
|
|
hexmask.long.byte 0x04 8.--15. 1. " EECP ,EHCI Extended Capabilities Pointer"
|
|
bitfld.long 0x04 4.--7. " IST ,Isochronous Scheduling Threshold" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x04 2. " ASP ,Asynchronous Schedule Park Capability" "Disabled,Enabled"
|
|
bitfld.long 0x04 1. " PFL ,Programmable Frame List Flag" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 0. " ADC ,64-bit Addressing Capability" "Disabled,Enabled"
|
|
rgroup.word 0x120++0x01
|
|
line.word 0x00 "UOG_DCIVERSION,Device Interface Version Number Register"
|
|
hexmask.word 0x00 0.--15. 1. " DCIVERSION ,Device Interface Version Number"
|
|
rgroup.long 0x124++0x03
|
|
line.long 0x00 "UOG_DCCPARAMS,Device Control Capability Parameters Register"
|
|
bitfld.long 0x00 8. " HC ,Host Capable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " DC ,Device Capable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--4. " DEN ,Device Endpoint Number" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,?..."
|
|
group.long 0x80++0x13
|
|
line.long 0x00 "UOG_GPTIMER0LD,General Purpose Timer 0 Load Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " GPTLD ,General Purpose Timer Load Value"
|
|
line.long 0x04 "UOG_GPTIMER0CTRL,Timer 0 Control Register"
|
|
bitfld.long 0x04 31. " GPTRUN ,General Purpose Timer Run" "Stopped,Started"
|
|
bitfld.long 0x04 30. " GPTRST ,General Purpose Timer Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 24. " GPMOD ,General Purpose Timer Mode" "One Shot,Repeat"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " GPTCNT ,General Purpose Timer Counter."
|
|
line.long 0x08 "UOG_GPTIMER1LD,General Purpose Timer 1 Load Register"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " GPTLD ,General Purpose Timer Load Value"
|
|
line.long 0x0C "UOG_GPTIMER1CTRL,Timer 1 Control Register"
|
|
bitfld.long 0x0C 31. " GPTRUN ,General Purpose Timer Run" "Stopped,Started"
|
|
bitfld.long 0x0C 30. " GPTRST ,General Purpose Timer Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x0C 24. " GPTMOD ,General Purpose Timer Mode" "One Shot,Repeat"
|
|
hexmask.long.tbyte 0x0C 0.--23. 1. " GPCNT ,General Purpose Timer Counter."
|
|
line.long 0x10 "UOG_SBUSCFG,Control for the system bus interface Register"
|
|
bitfld.long 0x10 0.--2. " AHBBRST ,AMBA AHB BURST" "INCR unspecified burst length,INCR4 non-multiple transfer/Singles,INCR8 non-multiple transfer/INCR4 or singles,INCR16 non-multiple transfer/INCR8 4 or singles,Reserved,INCR4 non-multiple transfer/Unspecified length,INCR8 non-multiple transfer/Unspecified length,INCR16 non-multiple transfer/Unspecified length"
|
|
group.long 0x140++0xF
|
|
line.long 0x00 "UOG_USBCMD,USB Command Register"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control"
|
|
textline " "
|
|
bitfld.long 0x00 14. " ATDTW ,ATDTW" "Cleared,Set"
|
|
bitfld.long 0x00 13. " SUTW ,Setup TripWire" "Hazard,No hazard"
|
|
textline " "
|
|
bitfld.long 0x00 11. " ASPE ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 8.--9. " ASP ,Asynchronous Schedule Park Mode Count" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 7. " LR ,Light Host/Device Controller Reset" "No effect,Reset"
|
|
bitfld.long 0x00 6. " IAA ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. 3. 15. " FS[2:0] ,Frame List Size" "1024,512,256,128,64,32,16,8"
|
|
bitfld.long 0x00 1. " RST ,Controller Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run"
|
|
line.long 0x04 "UOG_USBSTS,USB Status Register"
|
|
eventfld.long 0x04 25. " TI1 ,General Purpose Timer Interrupt 1" "No interrupt,Interrupt"
|
|
eventfld.long 0x04 24. " TI2 ,General Purpose Timer Interrupt 0" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x04 16. " NAKI ,NAK Interrupt Bit" "Cleared,Set"
|
|
bitfld.long 0x04 15. " AS ,Asynchronous Schedule Status" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 14. " PS ,Periodic Schedule Status" "Disabled,Enabled"
|
|
bitfld.long 0x04 13. " RCL ,Reclamation" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x04 12. " HCH ,HCHaIted" "Not halted,Halted"
|
|
eventfld.long 0x04 10. " ULPII ,ULPI Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 8. " SLI ,DCSuspend" "Not suspended,Suspended"
|
|
eventfld.long 0x04 7. " SRI ,SOF Received" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " URI ,USB Reset Received" "No reset,Reset"
|
|
eventfld.long 0x04 5. " AAI ,Interrupt on Async Advance" "Not requested,Requested"
|
|
textline " "
|
|
eventfld.long 0x04 4. " SEI ,System Error (Reserved))" "No error,Error"
|
|
eventfld.long 0x04 3. " FRI ,Frame List Rollover" "Not rollover,Rollover"
|
|
textline " "
|
|
eventfld.long 0x04 2. " PCI ,Port Change Detect" "Not changed,Changed"
|
|
eventfld.long 0x04 1. " UEI ,USB Error Interrupt" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x04 0. " UI ,USB Interrupt" "No interrupt,Interrupt"
|
|
line.long 0x08 "UOG_USBINTR,USB Interrupt Enable"
|
|
bitfld.long 0x08 25. " TIE1 ,General Purpose Timer Interrupt 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " TIE2 ,General Purpose Timer Interrupt 0 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 10. " ULPIE ,ULPI Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " SLE ,Sleep Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " SRE ,SOF Received Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " URE ,USB Reset Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 5. " AAE ,Interrupt on Async Advance Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 4. " SEE ,System Error Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 3. " FRE ,Frame List Rollover Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " PCE ,Port Change Detect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " UEE ,USB Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " UE ,USB Interrupt Enable" "Disabled,Enabled"
|
|
width 22.
|
|
line.long 0x0c "UOG_FRINDEX,USB Frame Index Register"
|
|
hexmask.long.word 0x0c 0.--13. 1. " FRINDEX ,Frame Index"
|
|
;if for host
|
|
if ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x3)
|
|
group.long 0x154++0x03
|
|
line.long 0x00 "UOG_PERIODICLISTBASE,Host Controller Frame List Base Address Register"
|
|
hexmask.long.tbyte 0x00 12.--31. 0x10 " BASEADR ,Base Address (Low)"
|
|
;if for device
|
|
elif ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x2)
|
|
group.long 0x154++0x03
|
|
line.long 0x00 "UOG_DEVICEADDR,Device Controller USB Device Address Register"
|
|
hexmask.long.byte 0x00 25.--31. 0x2 " USBADR ,Device Address"
|
|
else
|
|
hgroup.long 0x154++0x03
|
|
hide.long 0x00 "UOG_PERIODICLISTBASE,Device Controller USB Device Address Register"
|
|
endif
|
|
if ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x3)
|
|
group.long 0x158++0x03
|
|
line.long 0x00 "UOG_ASYNCLISTADDR,Host Controller Next Asynch Address Register"
|
|
hexmask.long 0x00 5.--31. 0x20 " ASYBASE ,Link Pointer Low"
|
|
elif ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x2)
|
|
group.long 0x158++0x03
|
|
line.long 0x00 "UOG_ENDPOINTLISTADDR,Device Controller Endpoint List Address Register"
|
|
hexmask.long.tbyte 0x00 11.--31. 0x8 " EPBASE ,Device Controller Endpoint List Address"
|
|
else
|
|
hgroup.long 0x158++0x03
|
|
hide.long 0x00 "UOG_ASYNCLISTADDR,Device Controller Endpoint List Address Register"
|
|
endif
|
|
group.long 0x160++0x7
|
|
line.long 0x00 "UOG_BURSTSIZE,Host Controller Embedded TT Async Buffer Status Register"
|
|
hexmask.long.word 0x00 8.--16. 1. " TXPBURST ,Programmable TX Burst Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RXPBURST ,Programmable RX Burst Length"
|
|
line.long 0x04 "UOG_TXFILLTUNING,TX FIFO Fill Tuning Register"
|
|
hexmask.long.byte 0x04 16.--21. 1. " TXFIFOTHRES ,TXFIFOTHRES"
|
|
hexmask.long.byte 0x04 8.--12. 1. " TXSCHEALTH ,TXSCHEALTH"
|
|
textline " "
|
|
hexmask.long.byte 0x04 0.--7. 1. " TXSCHOH ,TXSCHOH"
|
|
width 13.
|
|
if ((data.long(asd:(0x53FF4000+0x170))&0x20000000)==0x20000000)
|
|
group.long 0x170++0x03
|
|
line.long 0x00 "UOG_ULPIVIEW,ULPI Vieport Register"
|
|
bitfld.long 0x00 31. " ULPIWU ,ULPI Wakeup" "No wakeup,Wakeup"
|
|
bitfld.long 0x00 30. " ULPIRUN ,ULPI Read/Write Run" "No operation,Write"
|
|
textline " "
|
|
bitfld.long 0x00 29. " ULPIRW ,ULPI Read/Write Control" "Read,Write"
|
|
bitfld.long 0x00 27. " ULPISS ,ULPI Sync State" "Not normal,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 24.--26. " ULPIPORT ,ULPI Port Number" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ULPIADDR ,ULPI Data Address"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " ULPIDATRD ,ULPI Data Read"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ULPIDATWR ,ULPI Data Write"
|
|
else
|
|
group.long 0x170++0x03
|
|
line.long 0x00 "UOG_ULPIVIEW,ULPI Vieport Register"
|
|
bitfld.long 0x00 31. " ULPIWU ,ULPI Wakeup" "No wakeup,Wakeup"
|
|
bitfld.long 0x00 30. " ULPIRUN ,ULPI Read/Write Run" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 29. " ULPIRW ,ULPI Read/Write Control" "Read,Write"
|
|
bitfld.long 0x00 27. " ULPISS ,ULPI Sync State" "Not normal,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 24.--26. " ULPIPORT ,ULPI Port Number" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ULPIADDR ,ULPI Data Address"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " ULPIDATRD ,ULPI Data Read"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ULPIDATWR ,ULPI Data Write"
|
|
endif
|
|
group.long 0x178++0x07
|
|
line.long 0x00 "ENDPTNAK,Endpoint NAK"
|
|
eventfld.long 0x00 23. " EPTN ,Endpoint 7" "Not sent,Sent"
|
|
eventfld.long 0x00 22. " EPTN ,Endpoint 6" "Not sent,Sent"
|
|
eventfld.long 0x00 21. " EPTN ,Endpoint 5" "Not sent,Sent"
|
|
eventfld.long 0x00 20. " EPTN ,Endpoint 4" "Not sent,Sent"
|
|
textline " "
|
|
eventfld.long 0x00 19. " EPTN ,Endpoint 3" "Not sent,Sent"
|
|
eventfld.long 0x00 18. " EPTN ,Endpoint 2" "Not sent,Sent"
|
|
eventfld.long 0x00 17. " EPTN ,Endpoint 1" "Not sent,Sent"
|
|
eventfld.long 0x00 16. " EPTN ,Endpoint 0" "Not sent,Sent"
|
|
textline " "
|
|
eventfld.long 0x00 7. " EPRN ,Endpoint 7" "Not sent,Sent"
|
|
eventfld.long 0x00 6. " EPRN ,Endpoint 6" "Not sent,Sent"
|
|
eventfld.long 0x00 5. " EPRN ,Endpoint 5" "Not sent,Sent"
|
|
eventfld.long 0x00 4. " EPRN ,Endpoint 4" "Not sent,Sent"
|
|
textline " "
|
|
eventfld.long 0x00 3. " EPRN ,Endpoint 3" "Not sent,Sent"
|
|
eventfld.long 0x00 2. " EPRN ,Endpoint 2" "Not sent,Sent"
|
|
eventfld.long 0x00 1. " EPRN ,Endpoint 1" "Not sent,Sent"
|
|
eventfld.long 0x00 0. " EPRN ,Endpoint 0" "Not sent,Sent"
|
|
line.long 0x04 "ENDPTNAKEN,Endpoint NAK Enable"
|
|
bitfld.long 0x04 23. " EPTNE ,Endpoint 7" "Disabled,Enabled"
|
|
bitfld.long 0x04 22. " EPTNE ,Endpoint 6" "Disabled,Enabled"
|
|
bitfld.long 0x04 21. " EPTNE ,Endpoint 5" "Disabled,Enabled"
|
|
bitfld.long 0x04 20. " EPTNE ,Endpoint 4" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 19. " EPTNE ,Endpoint 3" "Disabled,Enabled"
|
|
bitfld.long 0x04 18. " EPTNE ,Endpoint 2" "Disabled,Enabled"
|
|
bitfld.long 0x04 17. " EPTNE ,Endpoint 1" "Disabled,Enabled"
|
|
bitfld.long 0x04 16. " EPTNE ,Endpoint 0" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 7. " EPRNE ,Endpoint 7" "Disabled,Enabled"
|
|
bitfld.long 0x04 6. " EPRNE ,Endpoint 6" "Disabled,Enabled"
|
|
bitfld.long 0x04 5. " EPRNE ,Endpoint 5" "Disabled,Enabled"
|
|
bitfld.long 0x04 4. " EPRNE ,Endpoint 4" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 3. " EPRNE ,Endpoint 3" "Disabled,Enabled"
|
|
bitfld.long 0x04 2. " EPRNE ,Endpoint 2" "Disabled,Enabled"
|
|
bitfld.long 0x04 1. " EPRNE ,Endpoint 1" "Disabled,Enabled"
|
|
bitfld.long 0x04 0. " EPRNE ,Endpoint 0" "Disabled,Enabled"
|
|
;if for host
|
|
if ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x3)
|
|
group.long 0x184++0x1F
|
|
line.long 0x0 "UOG_PORTSC1,Port 1 Status and Control Register"
|
|
bitfld.long 0x0 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x0 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x0 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x0 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x0 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x0 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x0 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x0 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x0 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x0 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x0 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x0 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x0 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x0 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x0 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x0 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x0 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x0 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x0 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x0 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x0 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x4 "UOG_PORTSC2,Port 2 Status and Control Register"
|
|
bitfld.long 0x4 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x4 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x4 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x4 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x4 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x4 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x4 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x4 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x4 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x4 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x4 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x4 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x4 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x4 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x4 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x4 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x4 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x4 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x4 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x4 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x4 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x8 "UOG_PORTSC3,Port 3 Status and Control Register"
|
|
bitfld.long 0x8 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x8 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x8 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x8 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x8 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x8 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x8 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x8 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x8 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x8 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x8 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x8 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x8 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x8 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x8 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x8 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x8 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x8 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x8 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x8 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0xC "UOG_PORTSC4,Port 4 Status and Control Register"
|
|
bitfld.long 0xC 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0xC 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0xC 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0xC 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0xC 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0xC 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0xC 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0xC 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0xC 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0xC 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0xC 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0xC 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0xC 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0xC 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0xC 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0xC 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0xC 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0xC 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0xC 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0xC 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0xC 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x10 "UOG_PORTSC5,Port 5 Status and Control Register"
|
|
bitfld.long 0x10 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x10 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x10 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x10 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x10 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x10 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x10 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x10 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x10 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x10 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x10 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x10 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x10 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x10 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x10 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x10 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x10 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x10 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x10 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x10 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x10 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x14 "UOG_PORTSC6,Port 6 Status and Control Register"
|
|
bitfld.long 0x14 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x14 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x14 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x14 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x14 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x14 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x14 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x14 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x14 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x14 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x14 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x14 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x14 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x14 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x14 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x14 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x14 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x14 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x14 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x14 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x14 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x18 "UOG_PORTSC7,Port 7 Status and Control Register"
|
|
bitfld.long 0x18 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x18 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x18 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x18 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x18 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x18 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x18 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x18 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x18 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x18 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x18 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x18 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x18 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x18 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x18 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x18 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x18 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x18 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x18 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x18 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x18 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x1C "UOG_PORTSC8,Port 8 Status and Control Register"
|
|
bitfld.long 0x1C 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x1C 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x1C 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x1C 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x1C 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x1C 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x1C 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x1C 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x1C 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x1C 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x1C 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x1C 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x1C 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x1C 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x1C 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 0. " CCS ,Current Connect Status" "No device,Device"
|
|
;if for device
|
|
elif ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x2)
|
|
group.long 0x184++0x03
|
|
line.long 0x00 "UOG_PORTSC1,Port 1 Status and Control Register"
|
|
bitfld.long 0x00 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x00 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x00 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x00 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x00 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x00 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x00 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,NAK,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x00 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x00 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x00 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x00 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x00 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x00 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x00 5. " OCO ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x00 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x00 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x00 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x00 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not attached,Attached"
|
|
else
|
|
hgroup.long 0x184++0x1F
|
|
hide.long 0x00 "UOG_PORTSC1,Port 1 Status and Control Register"
|
|
hide.long 0x04 "UOG_PORTSC2,Port 2 Status and Control Register"
|
|
hide.long 0x08 "UOG_PORTSC3,Port 3 Status and Control Register"
|
|
hide.long 0x0c "UOG_PORTSC4,Port 4 Status and Control Register"
|
|
hide.long 0x10 "UOG_PORTSC5,Port 5 Status and Control Register"
|
|
hide.long 0x14 "UOG_PORTSC6,Port 6 Status and Control Register"
|
|
hide.long 0x18 "UOG_PORTSC7,Port 7 Status and Control Register"
|
|
hide.long 0x1c "UOG_PORTSC8,Port 8 Status and Control Register"
|
|
endif
|
|
group.long 0x1a4++0x03
|
|
line.long 0x00 "UOG_OTGSC,OTG Status Control Register"
|
|
bitfld.long 0x00 30. " DPIE ,Data Pulse Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 29. " 1MSE ,1 Milisecond Timer Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 28. " BSEIE ,B Session End Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 27. " BSVIE ,B Session Valid Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 26. " ASVIE ,A Session Valid Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 25. " AVVIE ,A VBus Valid Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " IDIE ,USB ID Interrupt Enable" "Disabled,Enabled"
|
|
eventfld.long 0x00 22. " DPIS ,Data Pulse Interrupt Status" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 21. " 1MSS ,1 Milisecond Timer Interrupt Status" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 20. " BSEIS ,B Session End Interrupt Status" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 19. " BSVIS ,B Session Valid Interrupt Status" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 18. " ASVIS ,A Session Valid Interrupt Status" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x00 17. " AVVIS ,A VBus Valid Interrupt Status" "No interrupt,Interrupt"
|
|
eventfld.long 0x00 16. " IDIS ,USB ID Interrupt Status" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 14. " DPS ,Data Bus Pulsing Status" "Not detected,Detected"
|
|
bitfld.long 0x00 13. " 1MST ,1 Milisecond Timer Toggle" "Not toggled,Toggled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " BSE ,B Session End" "Not ended,Ended"
|
|
bitfld.long 0x00 11. " BSV ,B Session Valid" "Not valid,Valid"
|
|
textline " "
|
|
bitfld.long 0x00 10. " ASV ,A Session Valid" "Not valid,Valid"
|
|
bitfld.long 0x00 9. " AVV ,A VBus Valid" "Not valid,Valid"
|
|
textline " "
|
|
bitfld.long 0x00 8. " ID ,USB ID" "A device,B device"
|
|
bitfld.long 0x00 7. " HABA ,Hardware Assist B-Disconnect to A-connect Read/Write" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " HADP ,Hardware Assist Data-Pulse Write to Set" "Not started,Started"
|
|
bitfld.long 0x00 5. " IDPU ,ID Pullup" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " DP ,Data Pulsing" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " OT ,OTG Termination" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " VC ,VBUS Charge" "Not charged,Charged"
|
|
bitfld.long 0x00 0. " VD ,VBUS Discharge" "Not discharged,Discharged"
|
|
group.long 0x1a8++0x3
|
|
line.long 0x00 "UOG_USBMODE,USB Device Mode Register"
|
|
bitfld.long 0x00 4. " SDIS ,Stream Disable Mode" "Inactive,Active"
|
|
bitfld.long 0x00 3. " SLOM ,Setup Lockout Mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ES ,Endian Select" "Little,Big"
|
|
bitfld.long 0x00 0.--1. " CM ,Controller Mode" "Idle,Reserved,Device,Host"
|
|
width 20.
|
|
if ((data.long(asd:(0x53FF4000+0x1a8))&0x3)==0x2)
|
|
group.long 0x1ac++0xB
|
|
line.long 0x00 "UOG_ENDPTSETUPSTAT,Endpoint Setup Status Register"
|
|
eventfld.long 0x00 15. " ENDPTSETUPSTAT[15] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 14. " ENDPTSETUPSTAT[14] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " ENDPTSETUPSTAT[13] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 12. " ENDPTSETUPSTAT[12] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " ENDPTSETUPSTAT[11] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 10. " ENDPTSETUPSTAT[10] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 9. " ENDPTSETUPSTAT[9] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 8. " ENDPTSETUPSTAT[8] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 7. " ENDPTSETUPSTAT[7] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 6. " ENDPTSETUPSTAT[6] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 5. " ENDPTSETUPSTAT[5] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 4. " ENDPTSETUPSTAT[4] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 3. " ENDPTSETUPSTAT[3] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 2. " ENDPTSETUPSTAT[2] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 1. " ENDPTSETUPSTAT[1] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 0. " ENDPTSETUPSTAT[0] ,Setup Endpoint Status" "Not occurred,Occurred"
|
|
line.long 0x04 "UOG_ENDPTPRIME,Endpoint Initialization Register"
|
|
bitfld.long 0x04 31. " PETB15 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 30. " PETB14 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 29. " PETB13 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 28. " PETB12 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 27. " PETB11 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 26. " PETB10 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 25. " PETB9 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 24. " PETB8 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 23. " PETB7 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 22. " PETB6 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 21. " PETB5 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 20. " PETB4 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 19. " PETB3 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 18. " PETB2 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 17. " PETB1 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 16. " PETB0 ,Prime Endpoint Transmit Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 15. " PERB15 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 14. " PERB14 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 13. " PERB13 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 12. " PERB12 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 11. " PERB11 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 10. " PERB10 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 9. " PERB9 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 8. " PERB8 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 7. " PERB7 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 6. " PERB6 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 5. " PERB5 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 4. " PERB4 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 3. " PERB3 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 2. " PERB2 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
textline " "
|
|
bitfld.long 0x04 1. " PERB1 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
bitfld.long 0x04 0. " PERB0 ,Prime Endpoint Receive Buffer" "Not prime,Prime"
|
|
line.long 0x08 "UOG_ENDPTFLUSH,Endpoint De-Initialize Register"
|
|
bitfld.long 0x08 31. " FETB15 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 30. " FETB14 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 29. " FETB13 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 28. " FETB12 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 27. " FETB11 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 26. " FETB10 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 25. " FETB9 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 24. " FETB8 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 23. " FETB7 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 22. " FETB6 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 21. " FETB5 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 20. " FETB4 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 19. " FETB3 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 18. " FETB2 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 17. " FETB1 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 16. " FETB0 ,Flush Endpoint Transmit Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 15. " FERB15 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 14. " FERB14 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 13. " FERB13 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 12. " FERB12 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 11. " FERB11 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 10. " FERB10 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 9. " FERB9 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 8. " FERB8 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 7. " FERB7 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 6. " FERB6 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 5. " FERB5 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 4. " FERB4 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 3. " FERB3 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 2. " FERB2 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
textline " "
|
|
bitfld.long 0x08 1. " FERB1 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
bitfld.long 0x08 0. " FERB0 ,Flush Endpoint Receive Buffer" "Not flushed,Flushed"
|
|
rgroup.long 0x1b8++0x03
|
|
line.long 0x00 "UOG_ENDPTSTAT,Endpoint Status Register"
|
|
bitfld.long 0x00 31. " ETBR15 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 30. " ETBR14 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 29. " ETBR13 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 28. " ETBR12 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 27. " ETBR11 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 26. " ETBR10 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 25. " ETBR9 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 24. " ETBR8 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 23. " ETBR7 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 22. " ETBR6 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 21. " ETBR5 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 20. " ETBR4 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 19. " ETBR3 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 18. " ETBR2 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 17. " ETBR1 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 16. " ETBR0 ,Endpoint Transmit Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 15. " ERBR15 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 14. " ERBR14 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 13. " ERBR13 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 12. " ERBR12 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 11. " ERBR11 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 10. " ERBR10 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 9. " ERBR9 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 8. " ERBR8 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 7. " ERBR7 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 6. " ERBR6 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 5. " ERBR5 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 4. " ERBR4 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 3. " ERBR3 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 2. " ERBR2 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ERBR1 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
bitfld.long 0x00 0. " ERBR0 ,Endpoint Receive Buffer Ready" "Not ready,Ready"
|
|
group.long 0x1bc++0x03
|
|
line.long 0x00 "UOG_ENDPTCOMPLETE,Endpoint Compete Register"
|
|
eventfld.long 0x00 31. " ETCE15 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 30. " ETCE14 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 29. " ETCE13 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 28. " ETCE12 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 27. " ETCE11 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 26. " ETCE10 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 25. " ETCE9 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 24. " ETCE8 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 23. " ETCE7 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 22. " ETCE6 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 21. " ETCE5 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 20. " ETCE4 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 19. " ETCE3 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 18. " ETCE2 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 17. " ETCE1 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 16. " ETCE0 ,Endpoint Transmit Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 15. " ERCE15 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 14. " ERCE14 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 13. " ERCE13 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 12. " ERCE12 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 11. " ERCE11 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 10. " ERCE10 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 9. " ERCE9 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 8. " ERCE8 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 7. " ERCE7 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 6. " ERCE6 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 5. " ERCE5 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 4. " ERCE4 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 3. " ERCE3 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 2. " ERCE2 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 1. " ERCE1 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
eventfld.long 0x00 0. " ERCE0 ,Endpoint Receive Complete Event" "Not occurred,Occurred"
|
|
else
|
|
hgroup.long 0x1ac++0x13
|
|
hide.long 0x00 "UOG_ENDPTSETUPSTAT,Endpoint Setup Status Register"
|
|
hide.long 0x04 "UOG_ENDPTPRIME,Endpoint Initialization Register"
|
|
hide.long 0x08 "UOG_ENDPTFLUSH,Endpoint De-Initialize Register"
|
|
hide.long 0x0C "UOG_ENDPTSTAT,Endpoint Status Register"
|
|
hide.long 0x10 "UOG_ENDPTCOMPLETE,Endpoint Compete Register"
|
|
endif
|
|
group.long 0x1c0++0x3f
|
|
line.long 0x00 "UOG_ENDPTCTRL0,Endpoint Control 0 Register"
|
|
bitfld.long 0x00 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 18.--19. " TXT ,TX Endpoint Type" "Control,?..."
|
|
textline " "
|
|
bitfld.long 0x00 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
bitfld.long 0x00 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " RXT ,RX Endpoint Type" "Control,?..."
|
|
bitfld.long 0x00 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x4 "UOG_ENDPTCTRL1,Endpoint Control 1 Register"
|
|
bitfld.long 0x4 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x4 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x4 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x4 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x4 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x4 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x4 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x4 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x4 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x8 "UOG_ENDPTCTRL2,Endpoint Control 2 Register"
|
|
bitfld.long 0x8 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x8 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x8 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x8 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x8 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x8 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x8 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x8 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x8 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x8 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0xC "UOG_ENDPTCTRL3,Endpoint Control 3 Register"
|
|
bitfld.long 0xC 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0xC 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0xC 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0xC 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0xC 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0xC 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0xC 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0xC 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0xC 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0xC 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x10 "UOG_ENDPTCTRL4,Endpoint Control 4 Register"
|
|
bitfld.long 0x10 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x10 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x10 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x10 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x10 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x10 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x10 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x10 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x10 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x14 "UOG_ENDPTCTRL5,Endpoint Control 5 Register"
|
|
bitfld.long 0x14 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x14 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x14 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x14 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x14 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x14 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x14 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x14 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x14 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x14 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x18 "UOG_ENDPTCTRL6,Endpoint Control 6 Register"
|
|
bitfld.long 0x18 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x18 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x18 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x18 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x18 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x18 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x18 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x18 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x18 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x18 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x1C "UOG_ENDPTCTRL7,Endpoint Control 7 Register"
|
|
bitfld.long 0x1C 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x1C 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x1C 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x1C 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x1C 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x1C 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x1C 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x1C 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x1C 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x20 "UOG_ENDPTCTRL8,Endpoint Control 8 Register"
|
|
bitfld.long 0x20 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x20 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x20 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x20 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x20 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x20 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x20 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x20 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x20 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x20 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x20 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x20 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x24 "UOG_ENDPTCTRL9,Endpoint Control 9 Register"
|
|
bitfld.long 0x24 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x24 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x24 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x24 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x24 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x24 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x24 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x24 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x24 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x24 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x24 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x24 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x28 "UOG_ENDPTCTRL10,Endpoint Control 10 Register"
|
|
bitfld.long 0x28 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x28 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x28 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x28 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x28 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x28 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x28 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x28 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x28 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x28 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x28 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x28 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x2C "UOG_ENDPTCTRL11,Endpoint Control 11 Register"
|
|
bitfld.long 0x2C 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x2C 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x2C 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x2C 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x2C 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x2C 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x2C 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x2C 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x2C 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x2C 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x2C 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x2C 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x30 "UOG_ENDPTCTRL12,Endpoint Control 12 Register"
|
|
bitfld.long 0x30 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x30 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x30 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x30 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x30 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x30 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x30 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x30 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x30 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x30 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x30 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x30 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x34 "UOG_ENDPTCTRL13,Endpoint Control 13 Register"
|
|
bitfld.long 0x34 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x34 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x34 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x34 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x34 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x34 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x34 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x34 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x34 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x34 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x34 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x34 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x38 "UOG_ENDPTCTRL14,Endpoint Control 14 Register"
|
|
bitfld.long 0x38 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x38 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x38 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x38 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x38 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x38 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x38 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x38 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x38 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x38 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x38 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x38 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
line.long 0x3C "UOG_ENDPTCTRL15,Endpoint Control 15 Register"
|
|
bitfld.long 0x3C 23. " TXE ,TX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x3C 22. " TXR ,TX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x3C 21. " TXI ,TX Data Toggle Inhibit" "Enabled,Disabled"
|
|
bitfld.long 0x3C 18.--19. " TXT ,TX Endpoint Type" "Control,Isochronous,Bulk,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x3C 17. " TXD ,TX Endpoint Data Source" "Memory buffer,Undefined"
|
|
bitfld.long 0x3C 16. " TXS ,TX Endpoint Stall" "Not stalled,Stalled"
|
|
textline " "
|
|
bitfld.long 0x3C 7. " RXE ,RX Endpoint Enable" "Disabled,Enabled"
|
|
bitfld.long 0x3C 6. " RXR ,RX Data Toggle Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x3C 5. " RXI ,RX Data Toggle Inhibit" "Disabled,Enabled"
|
|
bitfld.long 0x3C 2.--3. " RXT ,RX Endpoint Type" "Control,Isochronous,Bulk,?..."
|
|
textline " "
|
|
bitfld.long 0x3C 1. " RXD ,RX Endpoint Data Sink" "Memory buffer,Undefined"
|
|
bitfld.long 0x3C 0. " RXS ,RX Endpoint Stall" "Not stalled,Stalled"
|
|
tree.end
|
|
width 18.
|
|
tree "HOST"
|
|
rgroup.long 0x400++0x17
|
|
line.long 0x00 "UH1_ID,Identification Register"
|
|
hexmask.long.byte 0x00 16.--23. 1. " REVISION ,Revision Number of the Core"
|
|
hexmask.long.byte 0x00 8.--13. 1. " NID ,Ones complement version of ID"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--5. 1. " ID ,Configuration Number"
|
|
line.long 0x04 "UH1_HWGENERAL,General Hardware Register"
|
|
bitfld.long 0x04 9. " SM ,VUSB_HS_PHY_SERIAL" "0,1"
|
|
bitfld.long 0x04 6.--8. " PHYM ,VUSB_HS_PHY_TYPE" "000,001,010,011,100,101,110,111"
|
|
textline " "
|
|
bitfld.long 0x04 4.--5. " PHYW ,VUSB_HS_PHY16_8" "00,01,10,11"
|
|
bitfld.long 0x04 3. " BWT ,Reserved for Internal Testing" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 1.--2. " CLKC ,VUSB_HS_CLOCK_CONFIGURATION" "00,01,10,11"
|
|
bitfld.long 0x04 0. " RT ,VUSB_HS_RESET_TYPE" "0,1"
|
|
line.long 0x08 "UH1_HWHOST,Host Hardware Parameters Register"
|
|
hexmask.long.byte 0x08 24.--31. 1. " TTPER ,VUSB_HS_TT_PERIODIC_CONTEXTS"
|
|
hexmask.long.byte 0x08 16.--23. 1. " TTASY ,VUSB_HS_TT_ASYNC_CONTEXTS"
|
|
textline " "
|
|
bitfld.long 0x08 1.--3. " NPORT ,VUSB_HS_NUM_PORT-1" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x08 0. " HC ,VUSB_HS_HOST" "0,1"
|
|
line.long 0x0c "UH1_HWDEVICE,Device Hardware Parameters Register"
|
|
hexmask.long.byte 0x0c 1.--5. 1. " DEVEP ,VUSB_HS_DEV_EP"
|
|
bitfld.long 0x0c 0. " DC ,VUSB_HS_DEV" "0,1"
|
|
line.long 0x10 "UH1_HWTXBUF,TX Buffer Hardware Parameters Register"
|
|
bitfld.long 0x10 31. " TXLCR ,VUSB_HS_TX_LOCAL_CONTEXT_REGISTERS" "0,1"
|
|
hexmask.long.byte 0x10 16.--23. 1. " TXCHANADD ,VUSB_HS_TX_CHAN_ADD"
|
|
textline " "
|
|
hexmask.long.byte 0x10 8.--15. 1. " TXADD ,VUSB_HS_TX_ADD"
|
|
hexmask.long.byte 0x10 0.--7. 1. " TCBURST ,VUSB_HS_TX_BURST"
|
|
line.long 0x14 "UH1_HWRXBUF,RX Buffer Hardware Parameters Register"
|
|
hexmask.long.byte 0x14 8.--15. 1. " RXADD ,VUSB_HS_RX_ADD"
|
|
hexmask.long.byte 0x14 0.--7. 1. " RXBURST ,VUSB_HS_RX_BURST"
|
|
rgroup.byte 0x500++0x00
|
|
line.byte 0x00 "UH1_CAPLENGTH,EHCI Compliant Register"
|
|
hexmask.byte 0x00 0.--7. 1. " CAPLENGTH ,Capability Length"
|
|
rgroup.word 0x502++0x01
|
|
line.word 0x00 "UH1_HCIVERSION,EHCI Compliant Register"
|
|
hexmask.word 0x00 0.--15. 1. " HCIVERSION ,Host Interface Version Number"
|
|
rgroup.long 0x504++0x07
|
|
line.long 0x00 "UH1_HCSPARAMS,EHCI Compliant With Extensions Register"
|
|
bitfld.long 0x00 24.--27. " N_TT ,Number of Transaction Translators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 20.--23. " N_PTT ,Number of Ports per Transaction Translator" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PI ,Port Indicators" "0,1"
|
|
bitfld.long 0x00 12.--15. " N_CC ,Number of Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x00 8.--11. " N_PCC ,Number of Ports per Companion Controller" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 4. " PPC ,Port Power Control" "Not included,Included"
|
|
textline " "
|
|
bitfld.long 0x00 0.--3. " N_PORTS ,Number of Downstream Ports" "Reserved,1,2,3,4,5,6,7,8,?..."
|
|
line.long 0x04 "UH1_HCCPARAMS,EHCI Compliant Register"
|
|
hexmask.long.byte 0x04 8.--15. 1. " EECP ,EHCI Extended Capabilities Pointer"
|
|
bitfld.long 0x04 4.--7. " IST ,Isochronous Scheduling Threshold" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x04 2. " ASP ,Asynchronous Schedule Park Capability" "Disabled,Enabled"
|
|
bitfld.long 0x04 1. " PFL ,Programmable Frame List Flag" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 0. " ADC ,64-bit Addressing Capability" "Disabled,Enabled"
|
|
group.long 0x480++0x0f
|
|
line.long 0x00 "UH1_GPTIMER0LD,General Purpose Timer 0 Load Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " GPTLD ,General Purpose Timer Load Value"
|
|
line.long 0x04 "UH1_GPTIMER0CTRL,Timer 0 Control Register"
|
|
bitfld.long 0x04 31. " GPTRUN ,General Purpose Timer Run" "Stopped,Started"
|
|
bitfld.long 0x04 30. " GPTRST ,General Purpose Timer Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x04 24. " GPMOD ,General Purpose Timer Mode" "One Shot,Repeat"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " GPTCNT ,General Purpose Timer Counter."
|
|
line.long 0x08 "UH1_GPTIMER1LD,General Purpose Timer 1 Load Register"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " GPTLD ,General Purpose Timer Load Value"
|
|
line.long 0x0C "UH1_GPTIMER1CTRL,Timer 1 Control Register"
|
|
bitfld.long 0x0C 31. " GPTRUN ,General Purpose Timer Run" "Stopped,Started"
|
|
bitfld.long 0x0C 30. " GPTRST ,General Purpose Timer Reset" "No effect,Reset"
|
|
textline " "
|
|
bitfld.long 0x0C 24. " GPTMOD ,General Purpose Timer Mode" "One Shot,Repeat"
|
|
hexmask.long.tbyte 0x0C 0.--23. 1. " GPCNT ,General Purpose Timer Counter."
|
|
group.long 0x540++0xF
|
|
line.long 0x00 "UH1_USBCMD,USB Command Register"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ITC ,Interrupt Threshold Control"
|
|
textline " "
|
|
bitfld.long 0x00 14. " ATDTW ,ATDTW" "Cleared,Set"
|
|
bitfld.long 0x00 13. " SUTW ,Setup TripWire" "Hazard,No hazard"
|
|
textline " "
|
|
bitfld.long 0x00 11. " ASPE ,Asynchronous Schedule Park Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 8.--9. " ASP ,Asynchronous Schedule Park Mode Count" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 7. " LR ,Light Host/Device Controller Reset" "No effect,Reset"
|
|
bitfld.long 0x00 6. " IAA ,Interrupt on Async Advance Doorbell" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 5. " ASE ,Asynchronous Schedule Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " PSE ,Periodic Schedule Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. 3. 15. " FS[2:0] ,Frame List Size" "1024,512,256,128,64,32,16,8"
|
|
textline " "
|
|
bitfld.long 0x00 1. " RST ,Controller Reset" "No effect,Reset"
|
|
bitfld.long 0x00 0. " RS ,Run/Stop" "Stop,Run"
|
|
line.long 0x04 "UH1_USBSTS,USB Status Register"
|
|
eventfld.long 0x04 25. " TI1 ,General Purpose Timer Interrupt 1" "No interrupt,Interrupt"
|
|
eventfld.long 0x04 24. " TI2 ,General Purpose Timer Interrupt 0" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x04 16. " NAKI ,NAK Interrupt Bit" "Cleared,Set"
|
|
bitfld.long 0x04 15. " AS ,Asynchronous Schedule Status" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 14. " PS ,Periodic Schedule Status" "Disabled,Enabled"
|
|
bitfld.long 0x04 13. " RCL ,Reclamation" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x04 12. " HCH ,HCHaIted" "Not halted,Halted"
|
|
eventfld.long 0x04 10. " ULPII ,ULPI Interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 8. " SLI ,DCSuspend" "Not suspended,Suspended"
|
|
eventfld.long 0x04 7. " SRI ,SOF Received" "Not detected,Detected"
|
|
textline " "
|
|
eventfld.long 0x04 6. " URI ,USB Reset Received" "No reset,Reset"
|
|
eventfld.long 0x04 5. " AAI ,Interrupt on Async Advance" "Not requested,Requested"
|
|
textline " "
|
|
eventfld.long 0x04 4. " SEI ,System Error (Reserved))" "No error,Error"
|
|
eventfld.long 0x04 3. " FRI ,Frame List Rollover" "Not rollover,Rollover"
|
|
textline " "
|
|
eventfld.long 0x04 2. " PCI ,Port Change Detect" "Not changed,Changed"
|
|
eventfld.long 0x04 1. " UEI ,USB Error Interrupt" "No error,Error"
|
|
textline " "
|
|
eventfld.long 0x04 0. " UI ,USB Interrupt" "No interrupt,Interrupt"
|
|
line.long 0x08 "UH1_USBINTR,USB Interrupt Enable"
|
|
bitfld.long 0x08 25. " TIE1 ,General Purpose Timer Interrupt 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 24. " TIE2 ,General Purpose Timer Interrupt 0 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 10. " ULPIE ,ULPI Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 8. " SLE ,Sleep Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " SRE ,SOF Received Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " URE ,USB Reset Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 5. " AAE ,Interrupt on Async Advance Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 4. " SEE ,System Error Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 3. " FRE ,Frame List Rollover Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 2. " PCE ,Port Change Detect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 1. " UEE ,USB Error Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x08 0. " UE ,USB Interrupt Enable" "Disabled,Enabled"
|
|
width 22.
|
|
line.long 0x0c "UH1_FRINDEX,USB Frame Index Register"
|
|
hexmask.long.word 0x0c 0.--13. 1. " FRINDEX ,Frame Index"
|
|
;if for host
|
|
if ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x3)
|
|
group.long 0x554++0x03
|
|
line.long 0x00 "UH1_PERIODICLISTBASE,Host Controller Frame List Base Address Register"
|
|
hexmask.long.tbyte 0x00 12.--31. 0x10 " BASEADR ,Base Address (Low)"
|
|
;if for device
|
|
elif ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x2)
|
|
group.long 0x554++0x03
|
|
line.long 0x00 "UH1_DEVICEADDR,Device Controller USB Device Address Register"
|
|
hexmask.long.byte 0x00 25.--31. 0x2 " USBADR ,Device Address"
|
|
else
|
|
hgroup.long 0x554++0x03
|
|
hide.long 0x00 "UH1_PERIODICLISTBASE,Device Controller USB Device Address Register"
|
|
endif
|
|
if ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x3)
|
|
group.long 0x558++0x03
|
|
line.long 0x00 "UH1_ASYNCLISTADDR,Host Controller Next Asynch Address Register"
|
|
hexmask.long 0x00 5.--31. 0x20 " ASYBASE ,Link Pointer Low"
|
|
elif ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x2)
|
|
group.long 0x558++0x03
|
|
line.long 0x00 "UH1_ENDPOINTLISTADDR,Device Controller Endpoint List Address Register"
|
|
hexmask.long.tbyte 0x00 11.--31. 0x8 " EPBASE ,Device Controller Endpoint List Address"
|
|
else
|
|
hgroup.long 0x558++0x03
|
|
hide.long 0x00 "UH1_ASYNCLISTADDR,Device Controller Endpoint List Address Register"
|
|
endif
|
|
group.long 0x560++0x7
|
|
line.long 0x00 "UH1_BURSTSIZE,Host Controller Embedded TT Async Buffer Status Register"
|
|
hexmask.long.word 0x00 8.--16. 1. " TXPBURST ,Programmable TX Burst Length"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RXPBURST ,Programmable RX Burst Length"
|
|
line.long 0x04 "UH1_TXFILLTUNING,TX FIFO Fill Tuning Register"
|
|
hexmask.long.byte 0x04 16.--21. 1. " TXFIFOTHRES ,TXFIFOTHRES"
|
|
hexmask.long.byte 0x04 8.--12. 1. " TXSCHEALTH ,TXSCHEALTH"
|
|
textline " "
|
|
hexmask.long.byte 0x04 0.--7. 1. " TXSCHOH ,TXSCHOH"
|
|
width 13.
|
|
if ((data.long(asd:(0x53FF4000+0x570))&0x20000000)==0x20000000)
|
|
group.long 0x570++0x03
|
|
line.long 0x00 "UH1_ULPIVIEW,ULPI Vieport Register"
|
|
bitfld.long 0x00 31. " ULPIWU ,ULPI Wakeup" "No wakeup,Wakeup"
|
|
bitfld.long 0x00 30. " ULPIRUN ,ULPI Read/Write Run" "No operation,Write "
|
|
textline " "
|
|
bitfld.long 0x00 29. " ULPIRW ,ULPI Read/Write Control" "Read,Write"
|
|
bitfld.long 0x00 27. " ULPISS ,ULPI Sync State" "Not normal,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 24.--26. " ULPIPORT ,ULPI Port Number" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ULPIADDR ,ULPI Data Address"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " ULPIDATRD ,ULPI Data Read"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ULPIDATWR ,ULPI Data Write"
|
|
else
|
|
group.long 0x570++0x03
|
|
line.long 0x00 "UH1_ULPIVIEW,ULPI Vieport Register"
|
|
bitfld.long 0x00 31. " ULPIWU ,ULPI Wakeup" "No wakeup,Wakeup"
|
|
bitfld.long 0x00 30. " ULPIRUN ,ULPI Read/Write Run" "Not read,Read "
|
|
textline " "
|
|
bitfld.long 0x00 29. " ULPIRW ,ULPI Read/Write Control" "Read,Write"
|
|
bitfld.long 0x00 27. " ULPISS ,ULPI Sync State" "Not normal,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 24.--26. " ULPIPORT ,ULPI Port Number" "0,1,2,3,4,5,6,7"
|
|
hexmask.long.byte 0x00 16.--23. 1. " ULPIADDR ,ULPI Data Address"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " ULPIDATRD ,ULPI Data Read"
|
|
hexmask.long.byte 0x00 0.--7. 1. " ULPIDATWR ,ULPI Data Write"
|
|
endif
|
|
;if for host
|
|
if ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x3)
|
|
group.long 0x584++0x1F
|
|
line.long 0x0 "UH1_PORTSC1,Port 1 Status and Control Register"
|
|
bitfld.long 0x0 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x0 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x0 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x0 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x0 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x0 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x0 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x0 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x0 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x0 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x0 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x0 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x0 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x0 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x0 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x0 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x0 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x0 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x0 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x0 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x0 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x4 "UH1_PORTSC2,Port 2 Status and Control Register"
|
|
bitfld.long 0x4 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x4 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x4 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x4 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x4 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x4 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x4 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x4 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x4 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x4 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x4 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x4 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x4 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x4 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x4 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x4 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x4 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x4 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x4 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x4 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x4 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x8 "UH1_PORTSC3,Port 3 Status and Control Register"
|
|
bitfld.long 0x8 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x8 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x8 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x8 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x8 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x8 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x8 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x8 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x8 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x8 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x8 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x8 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x8 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x8 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x8 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x8 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x8 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x8 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x8 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x8 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x8 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0xC "UH1_PORTSC4,Port 4 Status and Control Register"
|
|
bitfld.long 0xC 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0xC 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0xC 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0xC 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0xC 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0xC 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0xC 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0xC 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0xC 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0xC 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0xC 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0xC 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0xC 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0xC 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0xC 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0xC 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0xC 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0xC 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0xC 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0xC 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0xC 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x10 "UH1_PORTSC5,Port 5 Status and Control Register"
|
|
bitfld.long 0x10 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x10 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x10 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x10 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x10 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x10 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x10 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x10 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x10 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x10 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x10 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x10 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x10 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x10 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x10 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x10 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x10 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x10 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x10 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x10 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x10 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x10 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x14 "UH1_PORTSC6,Port 6 Status and Control Register"
|
|
bitfld.long 0x14 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x14 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x14 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x14 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x14 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x14 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x14 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x14 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x14 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x14 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x14 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x14 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x14 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x14 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x14 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x14 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x14 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x14 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x14 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x14 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x14 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x14 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x18 "UH1_PORTSC7,Port 7 Status and Control Register"
|
|
bitfld.long 0x18 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x18 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x18 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x18 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x18 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x18 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x18 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x18 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x18 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x18 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x18 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x18 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x18 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x18 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x18 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x18 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x18 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x18 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x18 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x18 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x18 0. " CCS ,Current Connect Status" "No device,Device"
|
|
line.long 0x1C "UH1_PORTSC8,Port 8 Status and Control Register"
|
|
bitfld.long 0x1C 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x1C 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x1C 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x1C 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x1C 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x1C 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x1C 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,SE0,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x1C 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x1C 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x1C 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x1C 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x1C 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x1C 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x1C 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x1C 5. " OCC ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x1C 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x1C 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x1C 0. " CCS ,Current Connect Status" "No device,Device"
|
|
;if for device
|
|
elif ((data.long(asd:(0x53FF4000+0x5a8))&0x3)==0x2)
|
|
group.long 0x584++0x03
|
|
line.long 0x00 "UH1_PORTSC1,Port 1 Status and Control Register"
|
|
bitfld.long 0x00 30.--31. " PTS ,Parallel Transceiver Select" "UTMI/UTMI+,Reserved,ULPI,Serial"
|
|
bitfld.long 0x00 29. " STS ,Serial Transceiver Select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x00 28. " PTW ,Parallel Transceiver Width" "8-bit,16-bit"
|
|
bitfld.long 0x00 26.--27. " PSPD ,Port Speed" "Full,Low,High,?..."
|
|
textline " "
|
|
bitfld.long 0x00 24. " PFSC ,Port Force Full Speed Connect" "Not forced,Forced"
|
|
bitfld.long 0x00 23. " PHCD ,PHY Low Power Suspend" "Not suspended,Suspended"
|
|
textline " "
|
|
bitfld.long 0x00 22. " WKOC ,Wake on Over-current Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 21. " WKDS ,Wake on Disconnect Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20. " WKCN ,Wake on Connect Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--19. " PTC ,Port Test Control" "Disabled,J_STATE,K_STATE,NAK,Packet,FORCE_ENABLE_HS,FORCE_ENABLE_FS,FORCE_ENABLE_LS,?..."
|
|
textline " "
|
|
bitfld.long 0x00 14.--15. " PIC ,Port Indicator Control" "Disabled,Amber,Green,?..."
|
|
bitfld.long 0x00 13. " PO ,Port Owner (Reserved)" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x00 12. " PP ,Port Power" "Not available,Available"
|
|
bitfld.long 0x00 10.--11. " LS ,Line Status" "SE0,J-state,K-state,?..."
|
|
textline " "
|
|
bitfld.long 0x00 9. " HSP ,High-Speed Port" "No high-speed,High-speed"
|
|
bitfld.long 0x00 8. " PR ,Port Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SUSP ,Suspend" "Not suspended,Suspended"
|
|
bitfld.long 0x00 6. " FPR ,Force Port Resume" "Not forced,Forced"
|
|
textline " "
|
|
eventfld.long 0x00 5. " OCO ,Over-current Change" "Not changed,Changed"
|
|
bitfld.long 0x00 4. " OCA ,Over-current Active" "No over-current,Over-current"
|
|
textline " "
|
|
eventfld.long 0x00 3. " PEC ,Port Enable/Disable Change" "Not changed,Changed"
|
|
bitfld.long 0x00 2. " PE ,Port Enabled/Disabled" "Disabled,Enabled"
|
|
textline " "
|
|
eventfld.long 0x00 1. " CSC ,Connect Status Change" "Not changed,Changed"
|
|
bitfld.long 0x00 0. " CCS ,Current Connect Status" "Not attached,Attached"
|
|
else
|
|
hgroup.long 0x584++0x1F
|
|
hide.long 0x00 "UH1_PORTSC1,Port 1 Status and Control Register"
|
|
hide.long 0x04 "UH1_PORTSC2,Port 2 Status and Control Register"
|
|
hide.long 0x08 "UH1_PORTSC3,Port 3 Status and Control Register"
|
|
hide.long 0x0c "UH1_PORTSC4,Port 4 Status and Control Register"
|
|
hide.long 0x10 "UH1_PORTSC5,Port 5 Status and Control Register"
|
|
hide.long 0x14 "UH1_PORTSC6,Port 6 Status and Control Register"
|
|
hide.long 0x18 "UH1_PORTSC7,Port 7 Status and Control Register"
|
|
hide.long 0x1c "UH1_PORTSC8,Port 8 Status and Control Register"
|
|
endif
|
|
group.long 0x5a8++0x3
|
|
line.long 0x00 "UH1_USBMODE,USB Device Mode Register"
|
|
bitfld.long 0x00 4. " SDIS ,Stream Disable Mode" "Inactive,Active"
|
|
bitfld.long 0x00 3. " SLOM ,Setup Lockout Mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ES ,Endian Select" "Little,Big"
|
|
bitfld.long 0x00 0.--1. " CM ,Controller Mode" "Idle,Reserved,Device,Host"
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree.open "EPIT (Enhanced Periodic Interrupt Timer)"
|
|
tree "EPIT 1"
|
|
base ad:0x53f94000
|
|
width 11.
|
|
group.long 0x00++0x03
|
|
line.long 0x00 "EPITCR1,EPIT Control Register"
|
|
bitfld.long 0x00 24.--25. " CLKSRC ,Select Clock Source" "Clock is off,Peripheral clock,High-frequency clock,Low-frequency clock"
|
|
bitfld.long 0x00 22.--23. " OM ,EPIT Output Configuration" "Disconnected,Toggled,Cleared,Set"
|
|
bitfld.long 0x00 21. " STOPEN ,EPIT Stop Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " EPIT ,EPIT Wait Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " DBGEN ,Debug Mode Enable" "Inactive,Active"
|
|
textline " "
|
|
bitfld.long 0x00 17. " IOVW ,EPIT Counter Overwrite Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " SWR ,Software Reset" "Out of reset,Reset"
|
|
hexmask.long.word 0x00 4.--15. 1. " PRESCALER ,Counter Clock Prescaler Value"
|
|
textline " "
|
|
bitfld.long 0x00 3. " RLD ,Counter Reload Control" "0xFFFFFFFF,Modulus register"
|
|
bitfld.long 0x00 2. " OCIEN ,Output Compare Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " ENMOD ,EPIT Enable Mode" "Current value,Load value"
|
|
textline " "
|
|
bitfld.long 0x00 0. " EN ,EPIT Enable" "Disabled,Enabled"
|
|
group.long 0x04++0x0b
|
|
line.long 0x00 "EPITSR1,EPIT Status Register"
|
|
eventfld.long 0x00 0. " OCIF ,Output Compare Interrupt Flag" "Not occurred,Occurred"
|
|
line.long 0x04 "EPITLR1,EPIT Load Register"
|
|
line.long 0x08 "EPITCMPR1,EPIT Compare Register"
|
|
rgroup.long 0x10++0x03
|
|
line.long 0x00 "EPITCNR1,EPIT Counter Register"
|
|
width 0xb
|
|
tree.end
|
|
tree "EPIT 2"
|
|
base ad:0x53f98000
|
|
width 11.
|
|
group.long 0x00++0x03
|
|
line.long 0x00 "EPITCR2,EPIT Control Register"
|
|
bitfld.long 0x00 24.--25. " CLKSRC ,Select Clock Source" "Clock is off,Peripheral clock,High-frequency clock,Low-frequency clock"
|
|
bitfld.long 0x00 22.--23. " OM ,EPIT Output Configuration" "Disconnected,Toggled,Cleared,Set"
|
|
bitfld.long 0x00 21. " STOPEN ,EPIT Stop Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 19. " EPIT ,EPIT Wait Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 18. " DBGEN ,Debug Mode Enable" "Inactive,Active"
|
|
textline " "
|
|
bitfld.long 0x00 17. " IOVW ,EPIT Counter Overwrite Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " SWR ,Software Reset" "Out of reset,Reset"
|
|
hexmask.long.word 0x00 4.--15. 1. " PRESCALER ,Counter Clock Prescaler Value"
|
|
textline " "
|
|
bitfld.long 0x00 3. " RLD ,Counter Reload Control" "0xFFFFFFFF,Modulus register"
|
|
bitfld.long 0x00 2. " OCIEN ,Output Compare Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " ENMOD ,EPIT Enable Mode" "Current value,Load value"
|
|
textline " "
|
|
bitfld.long 0x00 0. " EN ,EPIT Enable" "Disabled,Enabled"
|
|
group.long 0x04++0x0b
|
|
line.long 0x00 "EPITSR2,EPIT Status Register"
|
|
eventfld.long 0x00 0. " OCIF ,Output Compare Interrupt Flag" "Not occurred,Occurred"
|
|
line.long 0x04 "EPITLR2,EPIT Load Register"
|
|
line.long 0x08 "EPITCMPR2,EPIT Compare Register"
|
|
rgroup.long 0x10++0x03
|
|
line.long 0x00 "EPITCNR2,EPIT Counter Register"
|
|
width 0xb
|
|
tree.end
|
|
tree.end
|
|
tree "GPT (General Purpose Timer)"
|
|
base ad:0x53f90000
|
|
width 9.
|
|
group.long 0x00--0x1b
|
|
line.long 0x00 "GPTCR,GPT Control Register"
|
|
bitfld.long 0x00 31. " FO3 ,Force Output Compare Channel 3" "No effect,Compared"
|
|
bitfld.long 0x00 30. " F02 ,Force Output Compare Channel 2" "No effect,Compared"
|
|
bitfld.long 0x00 29. " FO1 ,Force Output Compare Channel 1" "No effect,Compared"
|
|
textline " "
|
|
bitfld.long 0x00 26.--28. " OM3 ,Output Compare Channel 3 Operating Mode" "Disconnected,Toggled,Cleared,Set,Pulse,Pulse,Pulse,Pulse"
|
|
bitfld.long 0x00 23.--25. " OM2 ,Output Compare Channel 2 Operating Mode" "Disconnected,Toggled,Cleared,Set,Pulse,Pulse,Pulse,Pulse"
|
|
bitfld.long 0x00 20.--22. " OM1 ,Output Compare Channel 1 Operating Mode" "Disconnected,Toggled,Cleared,Set,Pulse,Pulse,Pulse,Pulse"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " IM2 ,Input Capture Channel 2 Operating Mode" "Disabled,Rising edge,Falling edge,Both edges"
|
|
bitfld.long 0x00 16.--17. " IM1 ,Input Capture Channel 1 Operating Mode" "Disabled,Rising edge,Falling edge,Both edges"
|
|
bitfld.long 0x00 15. " SWR ,Software Reset" "Normal,Reset"
|
|
textline " "
|
|
bitfld.long 0x00 9. " FRR ,Freerun Or Restart Mode" "Reset,Freerun"
|
|
bitfld.long 0x00 6.--8. " CLKSRC ,Clock Source Select" "No clock,ipg_clk,ipg_clk_highfreq,ipp_ind_clkin,ipg_clk_32k,ipg_clk_32k,ipg_clk_32k,ipg_clk_32k"
|
|
bitfld.long 0x00 5. " STOPEN ,GPT Stop Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " WAITEN ,GPT Wait Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " DBGEN ,GPT Debug Mode Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ENMODE ,GPT Enable Mode" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " EN ,GPT Enable" "Disabled,Enabled"
|
|
line.long 0x04 "GPTPR,GPT Prescaler Register"
|
|
hexmask.long.word 0x04 0.--11. 1. " PRESCALER ,Prescaler"
|
|
line.long 0x08 "GPTSR,GPT Status Register"
|
|
eventfld.long 0x08 5. " ROV ,Rollover Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x08 4. " IF2 ,Input Capture 2 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x08 3. " IF1 ,Input Capture 1 Flag" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x08 2. " OF3 ,Output Compare 3 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x08 1. " OF2 ,Output Compare 2 Flag" "Not occurred,Occurred"
|
|
eventfld.long 0x08 0. " OF1 ,Output Compare 1Flag" "Not occurred,Occurred"
|
|
line.long 0x0c "GPTIR,GPT Interrupt Register"
|
|
bitfld.long 0x0C 5. " ROVIE ,Rollover Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 4. " IF2IE ,Input Capture 2 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 3. " IF1IE ,Input Capture 1 Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " OF3IE ,Output Compare 3 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 1. " OF2IE ,Output Compare 2Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 0. " OF1IE ,Output Compare 1Interrupt Enable" "Disabled,Enabled"
|
|
line.long 0x10 "GPTOCR1,GPT Output Compare Register 1"
|
|
line.long 0x14 "GPTOCR2,GPT Output Compare Register 2"
|
|
line.long 0x18 "GPTOCR3,GPT Output Compare Register 3"
|
|
rgroup.long 0x1c++0x0b
|
|
line.long 0x00 "GPTICR1,GPT Input Capture Register 1"
|
|
line.long 0x04 "GPTICR2,GPT Input Capture Register 2"
|
|
line.long 0x08 "GPTCNT,GPT Counter Register"
|
|
tree.end
|
|
tree "RTC (Real Time Clock)"
|
|
base ad:0x53fd8000
|
|
width 10.
|
|
group.long 0x00++0x27
|
|
line.long 0x00 "HOURMIN,RTC Hours And Minutes Counter Register"
|
|
bitfld.long 0x00 8.--12. " HOUR ,Hours Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,-,-,-,-,-,?..."
|
|
bitfld.long 0x00 0.--5. " MINUTES ,Minutes Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,?..."
|
|
line.long 0x04 "SECONDS,RTC Seconds Counter Register"
|
|
bitfld.long 0x04 0.--5. " SECONDS ,Seconds Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,?..."
|
|
line.long 0x08 "ALRM_HM,RTC Hours And Minutes Alarm Register"
|
|
bitfld.long 0x08 8.--12. " HOUR ,Hours Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,-,-,-,-,-,?..."
|
|
bitfld.long 0x08 0.--5. " MINUTES ,Minutes Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,?..."
|
|
line.long 0x0c "ALRM_SEC,RTC Seconds Alarm Register"
|
|
bitfld.long 0x0c 0.--5. " SECONDS ,Seconds Counter" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,?..."
|
|
line.long 0x10 "RTCCTL,RTC Control Register"
|
|
bitfld.long 0x10 7. " EN ,Enables/Disables The Real-Time Clock" "Disabled,Enabled"
|
|
bitfld.long 0x10 5.--6. " XTL ,Crystal Selection" "32.768 kHz,32 kHz,38.4 kHz,32.768 kHz"
|
|
bitfld.long 0x10 1. " GEN ,IPG_CLK Gating Enable" "Enabled,Disabled"
|
|
bitfld.long 0x10 0. " SWR ,Software Reset" "No effect,Reset"
|
|
line.long 0x14 "RTCISR,RTC Interrupt Status Register"
|
|
bitfld.long 0x14 15. " SAM7 ,Sampling Timer Interrupt Flag At SAM7 Frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 14. " SAM6 ,Sampling Timer Interrupt Flag At SAM6 Frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 13. " SAM5 ,Sampling Timer Interrupt Flag At SAM5 Frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 12. " SAM4 ,Sampling Timer Interrupt Flag At SAM4 Frequency" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 11. " SAM3 ,Sampling Timer Interrupt Flag At SAM3 Frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 10. " SAM2 ,Sampling Timer Interrupt Flag At SAM2 frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 9. " SAM1 ,Sampling Timer Interrupt Flag At SAM1 Frequency" "Not occurred,Occurred"
|
|
bitfld.long 0x14 8. " SAM0 ,Sampling Timer Interrupt Flag At SAM0 Frequency" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 7. " 2HZ ,2 Hz Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x14 5. " HR ,Hour Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x14 4. " 1HZ ,1 Hz Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x14 3. " DAY ,Day Flag" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x14 2. " ALM ,Alarm Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x14 1. " MIN ,Minute Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x14 0. " SW ,Stopwatch Flag" "Not time out,Timed out"
|
|
line.long 0x18 "RTCIENR,RTC Interrupt Enable Register"
|
|
bitfld.long 0x18 15. " SAM7 ,SAM7 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 14. " SAM6 ,SAM6 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 13. " SAM5 ,SAM5 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 12. " SAM4 ,SAM4 Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 11. " SAM3 ,SAM3 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 10. " SAM2 ,SAM2 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 9. " SAM1 ,SAM1 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 8. " SAM0 ,SAM0 Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 7. " 2HZ ,2HZ Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 5. " HR ,Hour Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 4. " 1HZ ,1HZ Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 3. " DAY ,DAY Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 2. " ALM ,Alarm Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 1. " MIN ,Minute Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x18 0. " SW ,Stopwatch Interrupt Enable" "Disabled,Enabled"
|
|
line.long 0x1c "STPWCH,RTC Stopwatch Minutes Register"
|
|
bitfld.long 0x1c 0.--5. " CNT ,Stopwatch Count" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
line.long 0x20 "DAYR,RTC Days Counter Register"
|
|
hexmask.long.word 0x20 0.--15. 1. " DAYS ,Day Setting"
|
|
line.long 0x24 "DAYALARM,RTC Day Alarm Register"
|
|
hexmask.long.word 0x24 0.--15. 1. " DAYSAL ,Day Setting Of The Alarm"
|
|
width 14.
|
|
tree.end
|
|
tree "WDOG (Watchdog Timer)"
|
|
base ad:0x53fdc000
|
|
width 0x6
|
|
group.word 0x00++0x3
|
|
line.word 0x00 "WCR,Watchdog Control Register"
|
|
hexmask.word.byte 0x00 8.--15. 1. " WT ,Watchdog Time-Out Field"
|
|
bitfld.word 0x00 7. " WDW ,Watchdog Disable for Wait" "Continue,Suspend"
|
|
bitfld.word 0x00 5. " WDA ,/Watchdog Assertion" "Asserted ,No effect"
|
|
textline " "
|
|
bitfld.word 0x00 4. " SRS ,/Software Reset Signal" "Reset,No effect"
|
|
bitfld.word 0x00 3. " WDT ,/WDOG Timeout assertion" "No effect,Asserted"
|
|
bitfld.word 0x00 2. " WDE ,Watchdog Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.word 0x00 1. " WDBG ,Watchdog DEBUG Enable" "Disabled,Suspend watchdog"
|
|
bitfld.word 0x00 0. " WDZST ,Watchdog Low Power" "Continue,Suspend"
|
|
line.word 0x02 "WSR,Watchdog Service Register"
|
|
hexmask.word 0x02 0.--15. 1. " WSR ,Watchdog Service"
|
|
rgroup.long 0x04++0x01
|
|
line.word 0x00 "WRSR,Watchdog Reset Status Register"
|
|
bitfld.word 0x00 1. " TOUT ,Time-Out" "No WDOG time-out,WDOG time-out"
|
|
bitfld.word 0x00 0. " SFTW ,Software Reset" "No software reset,Software reset"
|
|
group.word 0x6++0x3
|
|
line.word 0x0 "WICR,Watchdog Interrupt Control Register"
|
|
bitfld.word 0x0 15. " WIE ,Watchdog Timer Interrupt enable bit" "Disabled,Enabled"
|
|
eventfld.word 0x0 14. " WTIS ,Watchdog Timer Interrupt Status bit" "No interrupt,Interrupt"
|
|
hexmask.word.byte 0x0 0.--7. 1. " WICT ,Watchdog Interrupt Count Timeout (WICT) field"
|
|
line.word 0x2 "WMCR,Watchdog Miscellaneous Control Register"
|
|
bitfld.word 0x2 0. " PDE ,Power Down Counter Enable" "Disabled,Enabled"
|
|
width 0x16
|
|
tree.end
|
|
tree "CCM (Clock Controller Module)"
|
|
base ad:0x53f80000
|
|
width 6.
|
|
group.long 0x00++0x17
|
|
line.long 0x00 "CCMR,Control Register"
|
|
bitfld.long 0x00 30. " WFI ,Controls ccm_in_hold_off mode" "arm_wfi_pending,Never assert back"
|
|
bitfld.long 0x00 29. " STBY_EXIT_SRC ,Source of verification if external PMIC has put the voltage back to normal" "pmic_ready,Counter finished"
|
|
textline " "
|
|
bitfld.long 0x00 28. " VSTBY ,Supply Regulator Standby Mode Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 27. " WBEN ,ARM/EMI Domain well Bias Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 20.--23. " VOL_RDY_CNT ,Value of counter which need to wait for power supply ready" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 18.--19. " ROMW ,Wait State Control Bit from ARM ROM" "0-ARM/0-Alter,0-ARM/1-Alter,1-ARM/0-Alter,1-ARM/1-Alter"
|
|
textline " "
|
|
bitfld.long 0x00 16.--17. " RAMW ,Wait State Control Bits for ARM RAM" "0-ARM/0-Alter,?..."
|
|
bitfld.long 0x00 14.--15. " LPM ,Low Power Mode" "Run,Wait,Doze,Sleep"
|
|
textline " "
|
|
bitfld.long 0x00 9. " UPE ,USB PLL Enable Bit" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " MPE ,MCU PLL Enable" "Disabled,Enabled"
|
|
line.long 0x04 "PDR0,Post Divider Register"
|
|
bitfld.long 0x04 26. " PER_SEL ,Selects the synch perclk source" "ahb divided clock,arm high freq clock"
|
|
bitfld.long 0x04 23. " IPU_HND_BYP ,Controls the ipu handshake process bypass" "Not bypassed,Bypassed"
|
|
textline " "
|
|
bitfld.long 0x04 20.--21. " HSP_PODF ,Hsp root clock (532 MHz/400 MHz)" "133Mhz,66.5Mhz,178Mhz/133MHz,?..."
|
|
bitfld.long 0x04 16.--19. " CON_MUX_DIV ,ARM clock/Ahb clock" "532Mhz/133Mhz,399Mhz/133Mhz,266Mhz/133Mhz,Reserved,Reserved,Reserved,133Mhz/133Mhz,665Mhz/133Mhz,532Mhz/66.5Mhz,399Mhz/66.5Mhz,266Mhz/66.5Mhz,Reserved,Reserved,Reserved,133Mhz/66.5Mhz,?..."
|
|
textline " "
|
|
bitfld.long 0x04 15. " CKIL_SEL ,Select the 32k source" "24Mhz divided,Muxed io input"
|
|
bitfld.long 0x04 12.--14. " CCM_PER_AHB ,Controls the divider value from ahb clock to per_clk" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8"
|
|
textline " "
|
|
bitfld.long 0x04 0. " AUTO_CON ,Clock source" "Auto,Consumer"
|
|
line.long 0x08 "PDR1,Post Divider Register 1"
|
|
bitfld.long 0x08 28.--30. " MSHC_DIV_PRE ,MSHC baud clk pre divider value" "Reserved,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8"
|
|
bitfld.long 0x08 22.--27. " MSHC_DIV ,MSHC baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x08 7. " MSHC_M_U ,MSHC baud clk source" "Peripheral PLL,MPLL"
|
|
line.long 0x0C "PDR2,Post Divider Register 2"
|
|
bitfld.long 0x0C 27.--29. " SSI2_DIV_PRE ,SSI2 baud clk Pre divider value" "Reserved,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8"
|
|
bitfld.long 0x0C 24.--26. " SSI1_DIV_PRE ,SSI1 baud clk Pre divider value" "Reserved,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8"
|
|
textline " "
|
|
bitfld.long 0x0C 16.--21. " CSI_DIV ,CSI baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
bitfld.long 0x0C 8.--13. " SSI2_DIV ,SSI2 divider" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x0C 7. " CSI_M_U ,Selects the CSI baud clk source" "Peripheral PLL,MPLL"
|
|
bitfld.long 0x0C 6. " SSI_M_U ,Selects the SSI baud clk source" "Peripheral PLL,MPLL"
|
|
textline " "
|
|
bitfld.long 0x0C 0.--5. " SSI1_DIV ,SSI1 baud divider" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
line.long 0x10 "PDR3,Post Divider Register 3"
|
|
bitfld.long 0x10 29.--31. " SPDIF_DIV_PRE ,SPDIF baud clk pre divider value" "Reserved,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8"
|
|
bitfld.long 0x10 23.--28. " SPDIF_DIV ,SPDIF baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x10 22. " SPDIF_M_U ,Selects SPDIF baud clk source" "Peripheral PLL,MPLL"
|
|
bitfld.long 0x10 16.--21. " ESDHC3_DIV ,ESDHC3 baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x10 14. " UART_M_U ,Selects the UART baud clk source" "Peripheral PLL,MPLL"
|
|
bitfld.long 0x10 8.--13. " ESDHC2_DIV ,ESDHC3 baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x10 6. " ESDHC_M_U ,Selects the ESDHC baud clk source" "Peripheral PLL,MPLL"
|
|
bitfld.long 0x10 0.--5. " ESDHC1_DIV ,ESDHC3 baud clk divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
line.long 0x14 "PDR4,Post Divider Register 4"
|
|
bitfld.long 0x14 28.--31. " NFC_DIV ,NFC clock divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16"
|
|
bitfld.long 0x14 22.--27. " USB_DIV ,usb clock divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x14 16.--21. " PER0_DIV ,The synched per clock value from arm core clock" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
bitfld.long 0x14 10.--15. " UART_DIV ,uart baud clock divider value" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x14 9. " USB_M_U ,Selects the usb clk source" "Peripheral PLL,MPLL"
|
|
width 6.
|
|
if ((d.l(asd:(0x53f80000+0x18))&0x6000000)==0x0)
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "RCSR,Reset Control and Source Register"
|
|
bitfld.long 0x00 30.--31. " BT_USB_SRC ,USB SRC fuse/gpio value" "UTMI PHY,External ULPI PHY,ATLAS,PHILIPS ISP1301"
|
|
bitfld.long 0x00 29. " BUT_WIDTH ,Nand Bus Width from pad or fuse value" "8-bit,16-bit"
|
|
textline " "
|
|
bitfld.long 0x00 27.--28. " PAGE_SIZE ,Nand Flash Page Size from pad or fuse value" "512B,2kB,4kB/128B spare,4kB/218B spare"
|
|
bitfld.long 0x00 25.--26. " MEM_CTRL ,Boot memory type from pad or fuse value" "WEIM,NAND FLASH,Reserved,SD/MMC"
|
|
textline " "
|
|
bitfld.long 0x00 23.--24. " MEM_TYPE ,Boot memory type from pad or fuse value" "NOR,Reserved,Samsung OneNand,?..."
|
|
bitfld.long 0x00 22. " BT_ECC ,Boot ECC value" "4-bit,8-bit"
|
|
textline " "
|
|
bitfld.long 0x00 14. " NFC_16bit_SEL0 ,Software config for Nand Falsh width" "8-bit,16-bit"
|
|
bitfld.long 0x00 10.--11. " BOOT_REG ,Boot mode from boot mode pin" "Internal Boot,Function Test,External Boot,Boot Strap"
|
|
textline " "
|
|
bitfld.long 0x00 9. " NFC_4K ,NandFlash page size" "not 4k page,4k page"
|
|
bitfld.long 0x00 8. " NFC_FMS ,NandFlash page size" "not 2k page,2k page"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " GPF ,General purpose Flag Bits" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 0.--3. " REST ,Reset status" "POR external,Reserved,Jtag (s/w or ieee ),Reserved,Qualified external,Reserved,Reserved,Reserved,Watchdog timeout,?..."
|
|
elif ((d.l(asd:(0x53f80000+0x18))&0x6000000)==0x2000000)
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "RCSR,Reset Control and Source Register"
|
|
bitfld.long 0x00 30.--31. " BT_USB_SRC ,USB SRC fuse/gpio value" "UTMI PHY,External ULPI PHY,ATLAS,PHILIPS ISP1301"
|
|
bitfld.long 0x00 29. " BUT_WIDTH ,Nand Bus Width from pad or fuse value" "8-bit,16-bit"
|
|
textline " "
|
|
bitfld.long 0x00 27.--28. " PAGE_SIZE ,Nand Flash Page Size from pad or fuse value" "512B,2kB,4kB/128B spare,4kB/218B spare"
|
|
bitfld.long 0x00 25.--26. " MEM_CTRL ,Boot memory type from pad or fuse value" "WEIM,NAND FLASH,Reserved,SD/MMC"
|
|
textline " "
|
|
bitfld.long 0x00 23.--24. " MEM_TYPE ,Boot memory type from pad or fuse value" "3 address cycles,4 address cycles,5 address cycles,?..."
|
|
bitfld.long 0x00 22. " BT_ECC ,Boot ECC value" "4-bit,8-bit"
|
|
textline " "
|
|
bitfld.long 0x00 14. " NFC_16bit_SEL0 ,Software config for Nand Falsh width" "8-bit,16-bit"
|
|
bitfld.long 0x00 10.--11. " BOOT_REG ,Boot mode from boot mode pin" "Internal Boot,Function Test,External Boot,Boot Strap"
|
|
textline " "
|
|
bitfld.long 0x00 9. " NFC_4K ,NandFlash page size" "not 4k page,4k page"
|
|
bitfld.long 0x00 8. " NFC_FMS ,NandFlash page size" "not 2k page,2k page"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " GPF ,General purpose Flag Bits" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 0.--3. " REST ,Reset status" "POR external,Reserved,Jtag (s/w or ieee ),Reserved,Qualified external,Reserved,Reserved,Reserved,Watchdog timeout,?..."
|
|
elif ((d.l(asd:(0x53f80000+0x18))&0x6000000)==0x4000000)
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "RCSR,Reset Control and Source Register"
|
|
bitfld.long 0x00 30.--31. " BT_USB_SRC ,USB SRC fuse/gpio value" "UTMI PHY,External ULPI PHY,ATLAS,PHILIPS ISP1301"
|
|
bitfld.long 0x00 29. " BUT_WIDTH ,Nand Bus Width from pad or fuse value" "8-bit,16-bit"
|
|
textline " "
|
|
bitfld.long 0x00 27.--28. " PAGE_SIZE ,Nand Flash Page Size from pad or fuse value" "512B,2kB,4kB/128B spare,4kB/218B spare"
|
|
bitfld.long 0x00 25.--26. " MEM_CTRL ,Boot memory type from pad or fuse value" "WEIM,NAND FLASH,Reserved,SD/MMC"
|
|
textline " "
|
|
bitfld.long 0x00 23.--24. " MEM_TYPE ,Boot memory type from pad or fuse value" "CE-ATA HDD,P-ATA HDD,?..."
|
|
bitfld.long 0x00 22. " BT_ECC ,Boot ECC value" "4-bit,8-bit"
|
|
textline " "
|
|
bitfld.long 0x00 14. " NFC_16bit_SEL0 ,Software config for Nand Falsh width" "8-bit,16-bit"
|
|
bitfld.long 0x00 10.--11. " BOOT_REG ,Boot mode from boot mode pin" "Internal Boot,Function Test,External Boot,Boot Strap"
|
|
textline " "
|
|
bitfld.long 0x00 9. " NFC_4K ,NandFlash page size" "not 4k page,4k page"
|
|
bitfld.long 0x00 8. " NFC_FMS ,NandFlash page size" "not 2k page,2k page"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " GPF ,General purpose Flag Bits" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 0.--3. " REST ,Reset status" "POR external,Reserved,Jtag (s/w or ieee ),Reserved,Qualified external,Reserved,Reserved,Reserved,Watchdog timeout,?..."
|
|
else
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "RCSR,Reset Control and Source Register"
|
|
bitfld.long 0x00 30.--31. " BT_USB_SRC ,USB SRC fuse/gpio value" "UTMI PHY,External ULPI PHY,ATLAS,PHILIPS ISP1301"
|
|
bitfld.long 0x00 29. " BUT_WIDTH ,Nand Bus Width from pad or fuse value" "8-bit,16-bit"
|
|
textline " "
|
|
bitfld.long 0x00 27.--28. " PAGE_SIZE ,Nand Flash Page Size from pad or fuse value" "512B,2kB,4kB/128B spare,4kB/218B spare"
|
|
bitfld.long 0x00 25.--26. " MEM_CTRL ,Boot memory type from pad or fuse value" "WEIM,NAND FLASH,Reserved,SD/MMC"
|
|
textline " "
|
|
bitfld.long 0x00 23.--24. " MEM_TYPE ,Boot memory type from pad or fuse value" "SD/MMC,Reserved,Serial ROM via I2C,Serial ROM via SPI"
|
|
bitfld.long 0x00 22. " BT_ECC ,Boot ECC value" "4-bit,8-bit"
|
|
textline " "
|
|
bitfld.long 0x00 14. " NFC_16bit_SEL0 ,Software config for Nand Falsh width" "8-bit,16-bit"
|
|
bitfld.long 0x00 10.--11. " BOOT_REG ,Boot mode from boot mode pin" "Internal Boot,Function Test,External Boot,Boot Strap"
|
|
textline " "
|
|
bitfld.long 0x00 9. " NFC_4K ,NandFlash page size" "not 4k page,4k page"
|
|
bitfld.long 0x00 8. " NFC_FMS ,NandFlash page size" "not 2k page,2k page"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " GPF ,General purpose Flag Bits" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 0.--3. " REST ,Reset status" "POR external,Reserved,Jtag (s/w or ieee ),Reserved,Qualified external,Reserved,Reserved,Reserved,Watchdog timeout,?..."
|
|
endif
|
|
width 6.
|
|
group.long 0x1C++0x3F
|
|
line.long 0x00 "MPCTL,MCU PLL Control Register"
|
|
bitfld.long 0x00 31. " BRMO ,BRM Order Bit" "First,Second"
|
|
bitfld.long 0x00 26.--29. " PD ,Pre-Divider Factor" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16"
|
|
textline " "
|
|
hexmask.long.word 0x00 16.--25. 1. " MFD ,Multiplication Factor (Denominator Part)"
|
|
bitfld.long 0x00 10.--13. " MFI ,Multiplication Factor (Integer part)" "5,5,5,5,5,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--9. 1. " MFN ,Multiplication Factor (Numerator part)"
|
|
line.long 0x04 "PPCTL,Peripheral PLL Control Register"
|
|
bitfld.long 0x04 31. " BRMO ,BRM Order Bit" "First,Second"
|
|
bitfld.long 0x04 26.--29. " PD ,Pre-Divider Factor" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16"
|
|
textline " "
|
|
hexmask.long.word 0x04 16.--25. 1. " MFD ,Multiplication Factor (Denominator Part)"
|
|
bitfld.long 0x04 10.--13. " MFI ,Multiplication Factor (Integer part)" "5,5,5,5,5,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x04 0.--9. 1. " MFN ,Multiplication Factor (Numerator part)"
|
|
width 6.
|
|
line.long 0x08 "ACMR,AUDIO CLOCK MUX REGISTER"
|
|
hexmask.long.word 0x08 16.--27. 1. " CKILH_PODF ,EMI quick-refresh clock-divider value from 24 MHz oscillator input"
|
|
textline " "
|
|
bitfld.long 0x08 12.--15. " ESAI_AUDIO_CLK_SEL ,Selects audio source from ex ,Selects audio source from external 15 source and internal osc" "osc audio out,esai_ipp_do_sckt,esai_ipp_do_sckr,iomux_spdif_hckt_clk2,ssi1_output_ssi_srck,ssi1_output_ssi_stck,ssi2_output_ssi_srck,ssi2_output_ssi_stck,ccm_output_osc_audio_out,spdif_output_spdif_outclock,spdif_output_spdif_srclk,?..."
|
|
textline " "
|
|
bitfld.long 0x08 8.--11. " SPDIF_AUDIO_CLK_SEL ,Selects audio source from external 14 source and internal osc,ccm generating clk" "ccm clk,osc audio out,esai_ipp_do_sckt,esai_ipp_do_sckr,iomux_spdif_hckt_clk2,ssi1_output_ssi_srck,ssi1_output_ssi_stck,ssi2_output_ssi_srck,ssi2_output_ssi_stck,ccm_output_osc_audio_out,spdif_output_spdif_outclock,spdif_output_spdif_srclk,?..."
|
|
textline " "
|
|
bitfld.long 0x08 4.--7. " SSI1_AUDIO_CLK_SEL ,Selects audio source from external 14 source and internal osc,ccm generating clk" "ccm clk,osc audio out,esai_ipp_do_sckt,esai_ipp_do_sckr,iomux_spdif_hckt_clk2,ssi1_output_ssi_srck,ssi1_output_ssi_stck,ssi2_output_ssi_srck,ssi2_output_ssi_stck,ccm_output_osc_audio_out,spdif_output_spdif_outclock,spdif_output_spdif_srclk,?..."
|
|
textline " "
|
|
bitfld.long 0x08 0.--3. " SS2_AUDIO_CLK_SEL ,Selects audio source from external 14 source and internal osc,ccm generating clk" "ccm clk,osc audio out,esai_ipp_do_sckt,esai_ipp_do_sckr,iomux_spdif_hckt_clk2,ssi1_output_ssi_srck,ssi1_output_ssi_stck,ssi2_output_ssi_srck,ssi2_output_ssi_stck,ccm_output_osc_audio_out,spdif_output_spdif_outclock,spdif_output_spdif_srclk,?..."
|
|
line.long 0x0C "COSR,Clock Out Source Register"
|
|
bitfld.long 0x0C 26.--31. " ASRC_AUDIO_PODF ,Divider value from osc audio(24.576Mhz) to asrc clk input" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 9,Div by 10,Div by 11,Div by 12,Div by 13,Div by 14,Div by 15,Div by 16,Div by 17,Div by 18,Div by 19,Div by 20,Div by 21,Div by 22,Div by 23,Div by 24,Div by 25,Div by 26,Div by 27,Div by 28,Div by 29,Div by 30,Div by 31,Div by 32,Div by 33,Div by 34,Div by 35,Div by 36,Div by 37,Div by 38,Div by 39,Div by 40,Div by 41,Div by 42,Div by 43,Div by 44,Div by 45,Div by 46,Div by 47,Div by 48,Div by 49,Div by 50,Div by 51,Div by 52,Div by 53,Div by 54,Div by 55,Div by 56,Div by 57,Div by 58,Div by 59,Div by 60,Div by 61,Div by 62,Div by 63,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x0C 24. " ASRC_AUDIO_EN ,Enables the asrc clock from osc audio out " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 10.--15. " CLKO_DIV ,Divider value for CLKO" "Div by 1,Div by 2,Div by 3,Div by 4,Div by 5,Div by 6,Div by 7,Div by 8,Div by 2,Div by 4,Div by 6,Div by 8,Div by 10,Div by 12,Div by 14,Div by 16,Div by 3,Div by 6,Div by 9,Div by 12,Div by 15,Div by 18,Div by 21,Div by 24,Div by 4,Div by 8,Div by 12,Div by 16,Div by 20,Div by 24,Div by 28,Div by 32,Div by 5,Div by 10,Div by 15,Div by 20,Div by 25,Div by 30,Div by 35,Div by 40,Div by 6,Div by 12,Div by 18,Div by 24,Div by 30,Div by 36,Div by 42,Div by 48,Div by 7,Div by 14,Div by 21,Div by 28,Div by 35,Div by 42,Div by 49,Div by 56,Div by 8,Div by 16,Div by 24,Div by 32,Div by 40,Div by 48,Div by 56,Div by 64"
|
|
textline " "
|
|
bitfld.long 0x0c 7. " CKILH_CLKO ,CKIL or CKILH output to the CLKO ports" "CKIL,CKILH"
|
|
textline " "
|
|
bitfld.long 0x0C 6. " CLKO_DIV1 ,Controls the first divider value of CLKO clock" "Div by 1,Div by 2"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " CLKOEN ,Clock output enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 0.--4. " CLKOSEL ,Selects which clock is to be reflected on the clock output CKO" "async 32k,input 24Mhz for pll ref,input 24.576Mhz osc audio,Reserved,ppll_divgen output p75,mpll_divgen output 1x,per_pll output,arm clk,hclk always,ipg clk always,synched per clk root,usb clk,esdhc1 clk root,ssi1 clk root,mlb memory clk,mshc baud clock,mpll lock flag,csi clk root,spdif clk root,uart1 clk root,asrc audio input 768k clk,dptc ref clk 1 from ref cir,ARM core per clock,NFC clock,HSP clock,?..."
|
|
width 6.
|
|
line.long 0x10 "CGR0,Clock Gating Register 0"
|
|
bitfld.long 0x10 30.--31. " CG15 ,Clock Gating for Power Reduction in ESDHC3 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 28.--29. " CG14 ,Clock Gating for Power Reduction in ESDHC2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 26.--27. " CG13 ,Clock Gating for Power Reduction in ESDHC1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x10 24.--25. " CG12 ,Clock Gating for Power Reduction in ESAI (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 22.--23. " CG11 ,Clock Gating for Power Reduction in EPIT2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 20.--21. " CG10 ,Clock Gating for Power Reduction in EPIT1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x10 18.--19. " CG9 ,Clock Gating for Power Reduction in EMI (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 16.--17. " CG8 ,Clock Gating for Power Reduction in EDIO (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 14.--15. " CG7 ,Clock Gating for Power Reduction in ECT (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x10 12.--13. " CG6 ,Clock Gating for Power Reduction in CSPI2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 10.--11. " CG5 ,Clock Gating for Power Reduction in CSPI1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 8.--9. " CG4 ,Clock Gating for Power Reduction in CAN2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x10 6.--7. " CG3 ,Clock Gating for Power Reduction in CAN1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 4.--5. " CG2 ,Clock Gating for Power Reduction in AUDMUX (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x10 2.--3. " CG1 ,Clock Gating for Power Reduction in ATA (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x10 0.--1. " CG0 ,Clock Gating for Power Reduction in ASRC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
line.long 0x14 "CGR1,Clock Gating Register 1"
|
|
bitfld.long 0x14 30.--31. " CG15 ,Clock Gating for Power Reduction in RNGC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 28.--29. " CG14 ,Clock Gating for Power Reduction in PWM (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 26.--27. " CG13 ,Clock Gating for Power Reduction in OWIRE (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x14 24.--25. " CG12 ,Clock Gating for Power Reduction in MSHC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 22.--23. " CG11 ,Clock Gating for Power Reduction in MLB (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 20.--21. " CG10 ,Clock Gating for Power Reduction in KPP (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x14 18.--19. " CG9 ,Clock Gating for Power Reduction in IPU (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 16.--17. " CG8 ,Clock Gating for Power Reduction in IOMUXC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 14.--15. " CG7 ,Clock Gating for Power Reduction in I2C3 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x14 12.--13. " CG6 ,Clock Gating for Power Reduction in I2C2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 10.--11. " CG5 ,Clock Gating for Power Reduction in I2C1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 8.--9. " CG4 ,Clock Gating for Power Reduction in GPT (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x14 6.--7. " CG3 ,Clock Gating for Power Reduction in GPIO3 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 4.--5. " CG2 ,Clock Gating for Power Reduction in GPIO2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x14 2.--3. " CG1 ,Clock Gating for Power Reduction in GPIO1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x14 0.--1. " CG0 ,Clock Gating for Power Reduction in FEC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
line.long 0x18 "CGR2,Clock Gating Register 2"
|
|
bitfld.long 0x18 30.--31. " CG15 ,Clock Gating for Power Reduction in ADMUX (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 26.--27. " CG13 ,Clock Gating for Power Reduction in MAX (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 24.--25. " CG12 ,Clock Gating for Power Reduction in WDOG (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x18 22.--23. " CG11 ,Clock Gating for Power Reduction in USBOTG (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 20.--21. " CG10 ,Clock Gating for Power Reduction in UART3 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 18.--19. " CG9 ,Clock Gating for Power Reduction in UART2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x18 16.--17. " CG8 ,Clock Gating for Power Reduction in UART1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 14.--15. " CG7 ,Clock Gating for Power Reduction in SSI2 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 12.--13. " CG6 ,Clock Gating for Power Reduction in SSI1 (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x18 10.--11. " CG5 ,Clock Gating for Power Reduction in SPDIF (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 8.--9. " CG4 ,Clock Gating for Power Reduction in SPBA (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 6.--7. " CG3 ,Clock Gating for Power Reduction in SDMA (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
textline " "
|
|
bitfld.long 0x18 4.--5. " CG2 ,Clock Gating for Power Reduction in SCC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x18 0.--1. " CG0 ,Clock Gating for Power Reduction in RTC (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
line.long 0x1C "CGR3,Clock Gating Register 3"
|
|
bitfld.long 0x1C 4.--5. " CG2 ,Clock Gating for Power Reduction in GPU2D (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x1C 2.--3. " CG1 ,Clock Gating for Power Reduction in IIM (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
bitfld.long 0x1C 0.--1. " CG0 ,Clock Gating for Power Reduction in CSI(IPU csi perclk) (Run/Wait/Doze)" "OFF/OFF/OFF,ON/OFF/OFF,ON/ON/OFF,ON/ON/ON"
|
|
width 6.
|
|
group.long 0x40++0x1f
|
|
line.long 0x00 "DCVR0,DPTC Comparator Value Register 0"
|
|
hexmask.long.word 0x00 22.--31. 1. " ULV ,Upper Limit"
|
|
hexmask.long.word 0x00 12.--21. 1. " LLV ,Lower Limit"
|
|
hexmask.long.word 0x00 2.--11. 1. " ELV ,Emergency Limit"
|
|
line.long 0x04 "DCVR1,DPTC Comparator Value Register 1"
|
|
hexmask.long.word 0x04 22.--31. 1. " ULV ,Upper Limit"
|
|
hexmask.long.word 0x04 12.--21. 1. " LLV ,Lower Limit"
|
|
hexmask.long.word 0x04 2.--11. 1. " ELV ,Emergency Limit"
|
|
line.long 0x08 "DCVR2,DPTC Comparator Value Register 2"
|
|
hexmask.long.word 0x08 22.--31. 1. " ULV ,Upper Limit"
|
|
hexmask.long.word 0x08 12.--21. 1. " LLV ,Lower Limit"
|
|
hexmask.long.word 0x08 2.--11. 1. " ELV ,Emergency Limit"
|
|
line.long 0x0C "DCVR3,DPTC Comparator Value Register 3"
|
|
hexmask.long.word 0x0C 22.--31. 1. " ULV ,Upper Limit"
|
|
hexmask.long.word 0x0C 12.--21. 1. " LLV ,Lower Limit"
|
|
hexmask.long.word 0x0C 2.--11. 1. " ELV ,Emergency Limit"
|
|
width 6.
|
|
line.long 0x10 "LTR0,Load Tracking Register 0"
|
|
bitfld.long 0x10 31. " SIG15 ,Signal Detection on dvfs_w_sig 15" "Level,Edge"
|
|
bitfld.long 0x10 30. " SIG14 ,Signal Detection on dvfs_w_sig 14" "Level,Edge"
|
|
bitfld.long 0x10 29. " SIG13 ,Signal Detection on dvfs_w_sig 13" "Level,Edge"
|
|
textline " "
|
|
hexmask.long.byte 0x10 22.--27. 1. " UPTHR ,Upper Threshold for Load Tracking"
|
|
hexmask.long.byte 0x10 16.--21. 1. " DNTHR ,Lower Threshold for Load Tracking"
|
|
bitfld.long 0x10 15. " SIGD12 ,Signal Detection on dvfs_w_sig 12" "Level,Edge"
|
|
textline " "
|
|
bitfld.long 0x10 14. " SIGD11 ,Signal Detection on dvfs_w_sig 11" "Level,Edge"
|
|
bitfld.long 0x10 13. " SIGD10 ,Signal Detection on dvfs_w_sig 10" "Level,Edge"
|
|
bitfld.long 0x10 12. " SIGD9 ,Signal Detection on dvfs_w_sig 9" "Level,Edge"
|
|
textline " "
|
|
bitfld.long 0x10 11. " SIGD8 ,Signal Detection on dvfs_w_sig 8" "Level,Edge"
|
|
bitfld.long 0x10 10. " SIGD7 ,Signal Detection on dvfs_w_sig 7" "Level,Edge"
|
|
bitfld.long 0x10 9. " SIGD6 ,Signal Detection on dvfs_w_sig 6" "Level,Edge"
|
|
textline " "
|
|
bitfld.long 0x10 8. " SIGD5 ,Signal Detection on dvfs_w_sig 5" "Level,Edge"
|
|
bitfld.long 0x10 7. " SIGD4 ,Signal Detection on dvfs_w_sig 4" "Level,Edge"
|
|
bitfld.long 0x10 6. " SIGD3 ,Signal Detection on dvfs_w_sig 3" "Level,Edge"
|
|
textline " "
|
|
bitfld.long 0x10 5. " SIGD2 ,Signal Detection on dvfs_w_sig 2" "Level,Edge"
|
|
bitfld.long 0x10 4. " SIGD1 ,Signal Detection on dvfs_w_sig 1" "Level,Edge"
|
|
bitfld.long 0x10 3. " SIGD0 ,Signal Detection on dvfs_w_sig 0" "Level,Edge"
|
|
textline " "
|
|
bitfld.long 0x10 1.--2. " DIV3CK ,Division Value of div_3_clk" "1/2048,1/8192,1/32768,1/131072"
|
|
width 6.
|
|
line.long 0x14 "LTR1,Load Tracking Register 1"
|
|
bitfld.long 0x14 23. " LTBRSH ,Load Tracking Buffer Shift" "ld_add - ld_add[5:2],ld_add - ld_add[4:1]"
|
|
bitfld.long 0x14 22. " LTBRSR ,Load Tracking Buffer Source" "pre_ld_add,ld_add"
|
|
hexmask.long.byte 0x14 14.--21. 1. " DNCNT ,Number of Consecutive Times the Lower Frequency Threshold"
|
|
textline " "
|
|
hexmask.long.byte 0x14 6.--13. 1. " UPCNT ,Number of Consecutive Times the Upper Frequency Threshold"
|
|
hexmask.long.byte 0x14 0.--5. 1. " PNCTHR ,Panic Mode Level Threshold for Load Tracking"
|
|
width 6.
|
|
line.long 0x18 "LTR2,Load Tracking Register 1"
|
|
bitfld.long 0x18 29.--31. " WSW15 ,WSW15 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x18 26.--28. " WSW14 ,WSW14 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x18 23.--25. " WSW13 ,WSW13 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x18 20.--22. " WSW12 ,WSW12 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x18 17.--19. " WSW11 ,WSW11 Value" "000,001,010,011,100,101,110,111"
|
|
textline " "
|
|
bitfld.long 0x18 14.--16. " WSW10 ,WSW10 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x18 11.--13. " WSW9 ,WSW9 Value" "000,001,010,011,100,101,110,111"
|
|
hexmask.long.word 0x18 0.--8. 1. " EMAC ,EMA Configuration"
|
|
line.long 0x1C "LTR3,Load Tracking Register"
|
|
bitfld.long 0x1C 29.--31. " WSW8 ,WSW8 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 26.--28. " WSW7 ,WSW7 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 23.--25. " WSW6 ,WSW6 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 20.--22. " WSW5 ,WSW5 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 17.--19. " WSW4 ,WSW4 Value" "000,001,010,011,100,101,110,111"
|
|
textline " "
|
|
bitfld.long 0x1C 14.--16. " WSW3 ,WSW3 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 11.--13. " WSW2 ,WSW2 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 8.--10. " WSW1 ,WSW1 Value" "000,001,010,011,100,101,110,111"
|
|
bitfld.long 0x1C 5.--7. " WSW0 ,WSW0 Value" "000,001,010,011,100,101,110,111"
|
|
rgroup.long 0x60++0x7
|
|
line.long 0x00 "LTBR0,Load Tracking Buffer Register 0"
|
|
bitfld.long 0x00 28.--31. " LTS7 ,7th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 24.--27. " LTS6 ,6th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 20.--23. " LTS5 ,5th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 16.--19. " LTS4 ,4th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 12.--15. " LTS3 ,3rd Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x00 8.--11. " LTS2 ,2nd Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 4.--7. " LTS1 ,1th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x00 0.--3. " LTS0 ,0 Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
line.long 0x04 "LTBR1,Load Tracking Buffer Register 1"
|
|
bitfld.long 0x04 28.--31. " LTS15 ,15th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 24.--27. " LTS14 ,16th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 20.--23. " LTS13 ,13th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 16.--19. " LTS12 ,12th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 12.--15. " LTS11 ,11rd Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x04 8.--11. " LTS10 ,10nd Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 4.--7. " LTS9 ,9th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
bitfld.long 0x04 0.--3. " LTS8 ,8th Sample of Load Tracking" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
width 6.
|
|
group.long 0x68++0xB
|
|
line.long 0x00 "PMCR0,Power Management Control Register"
|
|
bitfld.long 0x00 28.--29. " DVSUP ,DVS update" "Highest,High,Low,Lowest"
|
|
bitfld.long 0x00 24. " DVFS_UPD_FINISH ,DVFS UPDATE finish by software" "Not finished,Finished"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DVFEV ,Always Give a DVFS Event" "Not always,Always"
|
|
bitfld.long 0x00 22. " DVFIS ,DVFS Interrupt Select" "SDMA for DVFS,MCU for DVFS"
|
|
textline " "
|
|
bitfld.long 0x00 21. " LBMI ,Load Buffer Full Mask Interrupt" "Enabled,Masked"
|
|
bitfld.long 0x00 20. " LBFL ,Load Buffer Full Status Bit" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " LBCF ,DVFS Load Buffer Programmable Size" "4,8,12,16"
|
|
bitfld.long 0x00 17. " PTVIS ,DPTC Interrupt Select" "SDMA for DPTC,MCU for DPTC"
|
|
textline " "
|
|
bitfld.long 0x00 16. " DVFS_START ,DVFS update start bit configured by software" "Not started,Started"
|
|
bitfld.long 0x00 15. " FSVAIM ,DVFS Frequency Adjustment Interrupt Mask" "Enabled,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 13.--14. " FSVAI[1:0] ,DVFS Frequency Adjustment Interrupt" "No interrupt,Increased,Decreased,Increased immediately"
|
|
bitfld.long 0x00 12. " DPVCR ,DPTC Voltage Change Request" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " DPVV ,DPTC Voltage Valid Edge Detect" "Not valid,Valid"
|
|
bitfld.long 0x00 10. " WFIM ,DVFS Wait for Interrupt Mask Bit" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 9. " DRCE3 ,DPTC Reference Circuit3 Enable Bit" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " DRCE2 , DPTC Reference Circuit2 Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " DRCE1 , DPTC Reference Circuit1 Enable Bit" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " DRCE0 , DPTC Reference Circuit0 Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " SCR ,DPTC Counting Range" "256,512"
|
|
bitfld.long 0x00 4. " DVFEN ,DVFS Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " PTVAIM ,DPTC Voltage Adjustment Interrupt Mask" "Enabled,Masked"
|
|
bitfld.long 0x00 1.--2. " PTVAI[1:0] ,DPTC Voltage Adjustment Interrupt" "No interrupt,Decreased,Increased,Increased immediately"
|
|
textline " "
|
|
bitfld.long 0x00 0. " DPTEN ,DPTC Enable" "Disabled,Enabled"
|
|
line.long 0x04 "PMCR1,Power Management Control Register"
|
|
bitfld.long 0x04 28. " CPFA_EMI ,EMI Well Bias Frequency Adjust" "Reduced,Full"
|
|
bitfld.long 0x04 24.--27. " CPSPA_EM ,Controls the Back Bias levle of NWELL and PWELL" "Increased(Nwells)/Increased(Pwells),Moderate(Nwells)/Increased(Pwells),Decreased(Nwells)/Increased(Pwells),Minimum(Nwells)/Increased(Pwells),Increased(Nwells)/Moderate(Pwells),Moderate(Nwells)/Moderate(Pwells),Decreased(Nwells)/Moderate(Pwells),Minimum(Nwells)/Moderate(Pwells),Increased(Nwells)/Decreased(Pwells),Moderate(Nwells)/Decreased(Pwells),Decreased(Nwells)/Decreased(Pwells),Minimum(Nwells)/Decreased(Pwells),Increased(Nwells)/Minimum(Pwells),Moderate(Nwells)/Minimum(Pwells),Decreased(Nwells)/Minimum(Pwells),Minimum(Nwells)/Minimum(Pwells)"
|
|
textline " "
|
|
hexmask.long.byte 0x04 16.--23. 1. " WBCN ,Well BIas counter"
|
|
bitfld.long 0x04 9.--12. " CPSPA ,Controls the Back Bias levle of NWELL and PWELL" "Increased(Nwells)/Increased(Pwells),Moderate(Nwells)/Increased(Pwells),Decreased(Nwells)/Increased(Pwells),Minimum(Nwells)/Increased(Pwells),Increased(Nwells)/Moderate(Pwells),Moderate(Nwells)/Moderate(Pwells),Decreased(Nwells)/Moderate(Pwells),Minimum(Nwells)/Moderate(Pwells),Increased(Nwells)/Decreased(Pwells),Moderate(Nwells)/Decreased(Pwells),Decreased(Nwells)/Decreased(Pwells),Minimum(Nwells)/Decreased(Pwells),Increased(Nwells)/Minimum(Pwells),Moderate(Nwells)/Minimum(Pwells),Decreased(Nwells)/Minimum(Pwells),Minimum(Nwells)/Minimum(Pwells)"
|
|
textline " "
|
|
bitfld.long 0x04 6. " CPFA ,WBCP Frequency Adjustment" "Reduced,Full"
|
|
hexmask.long.byte 0x04 0.--3. 1. " DVGP ,DVFS General Purpose"
|
|
line.long 0x08 "PMCR2,Power Management Control Register 2"
|
|
hexmask.long.word 0x08 23.--31. 1. " OSC_RDY_CNT ,OSC_RDY_CNT"
|
|
bitfld.long 0x08 21. " M1_GAS ,Control bit for gasket onEMI port1" "Used,Bypassed"
|
|
textline " "
|
|
bitfld.long 0x08 20. " M4_GAS ,Control bit for gasket onEMI port4" "Used,Bypassed"
|
|
bitfld.long 0x08 19. " M3_GAS ,Control bit for gasket onEMI port3" "Used,Bypassed"
|
|
textline " "
|
|
bitfld.long 0x08 18. " IPU_GAS ,Selects the gasket between IPU and EMI" "Used,Bypassed"
|
|
bitfld.long 0x08 17. " OSC_AUDIO_DOWN ,Controls the osc audio power supply" "On,Off"
|
|
textline " "
|
|
bitfld.long 0x08 16. " OSC24M_DOWN ,Control the osc 24Mhz power supply (in stop mode)" "Not powered off,Powered off"
|
|
hexmask.long.word 0x08 5.--15. 1. " REF_COUNTER_OUT ,DPTC reference circuit counter value which can be read through ipbus"
|
|
textline " "
|
|
bitfld.long 0x08 1. " DVFS_REQ ,control the osc audio power supply" "Not requested,Requested"
|
|
bitfld.long 0x08 0. " DVFS_ACK ,Shows the status of EMI has closed the access for SDRAM" "No ack signal,Acked"
|
|
width 0x14
|
|
tree.end
|
|
tree "SDMA (Smart Direct Memory Access)"
|
|
base ad:0x53FD4000
|
|
width 13.
|
|
group.long 0x00++0x13
|
|
line.long 0x00 "MC0PTR,AP Channel 0 Pointer Register"
|
|
line.long 0x04 "INTR,Channel Interrupts Register"
|
|
eventfld.long 0x04 31. " HI[31] ,AP HI[31] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 30. " HI[30] ,AP HI[30] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 29. " HI[29] ,AP HI[29] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 28. " HI[28] ,AP HI[28] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 27. " HI[27] ,AP HI[27] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 26. " HI[26] ,AP HI[26] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 25. " HI[25] ,AP HI[25] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 24. " HI[24] ,AP HI[24] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 23. " HI[23] ,AP HI[23] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 22. " HI[22] ,AP HI[22] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 21. " HI[21] ,AP HI[21] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 20. " HI[20] ,AP HI[20] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 19. " HI[19] ,AP HI[19] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 18. " HI[18] ,AP HI[18] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 17. " HI[17] ,AP HI[17] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 16. " HI[16] ,AP HI[16] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 15. " HI[15] ,AP HI[15] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 14. " HI[14] ,AP HI[14] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 13. " HI[13] ,AP HI[13] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 12. " HI[12] ,AP HI[12] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 11. " HI[11] ,AP HI[11] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 10. " HI[10] ,AP HI[10] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 9. " HI[9] ,AP HI[9] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 8. " HI[8] ,AP HI[8] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 7. " HI[7] ,AP HI[7] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 6. " HI[6] ,AP HI[6] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 5. " HI[5] ,AP HI[5] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 4. " HI[4] ,AP HI[4] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 3. " HI[3] ,AP HI[3] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 2. " HI[2] ,AP HI[2] Interrupt " "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x04 1. " HI[1] ,AP HI[1] Interrupt " "No interrupt,Interrupt"
|
|
eventfld.long 0x04 0. " HI[0] ,AP HI[0] Interrupt " "No interrupt,Interrupt"
|
|
line.long 0x08 "STOP_STAT,Channel Stop/Channel Status Register"
|
|
eventfld.long 0x08 31. " HE[31] ,HE[31] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 30. " HE[30] ,HE[30] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 29. " HE[29] ,HE[29] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 28. " HE[28] ,HE[28] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 27. " HE[27] ,HE[27] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 26. " HE[26] ,HE[26] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 25. " HE[25] ,HE[25] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 24. " HE[24] ,HE[24] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 23. " HE[23] ,HE[23] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 22. " HE[22] ,HE[22] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 21. " HE[21] ,HE[21] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 20. " HE[20] ,HE[20] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 19. " HE[19] ,HE[19] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 18. " HE[18] ,HE[18] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 17. " HE[17] ,HE[17] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 16. " HE[16] ,HE[16] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 15. " HE[15] ,HE[15] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 14. " HE[14] ,HE[14] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 13. " HE[13] ,HE[13] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 12. " HE[12] ,HE[12] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 11. " HE[11] ,HE[11] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 10. " HE[10] ,HE[10] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 9. " HE[9] ,HE[9] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 8. " HE[8] ,HE[8] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 7. " HE[7] ,HE[7] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 6. " HE[6] ,HE[6] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 5. " HE[5] ,HE[5] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 4. " HE[4] ,HE[4] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 3. " HE[3] ,HE[3] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 2. " HE[2] ,HE[2] Stop/Status" "No access,Access"
|
|
textline " "
|
|
eventfld.long 0x08 1. " HE[1] ,HE[1] Stop/Status" "No access,Access"
|
|
eventfld.long 0x08 0. " HE[0] ,HE[0] Stop/Status" "No access,Access"
|
|
line.long 0x0C "HSTART,Channel Start Register"
|
|
bitfld.long 0x0C 31. " HSTART[31] ,Channel 31 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 30. " HSTART[30] ,Channel 30 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 29. " HSTART[29] ,Channel 29 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 28. " HSTART[28] ,Channel 28 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 27. " HSTART[27] ,Channel 27 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 26. " HSTART[26] ,Channel 26 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 25. " HSTART[25] ,Channel 25 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 24. " HSTART[24] ,Channel 24 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 23. " HSTART[23] ,Channel 23 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 22. " HSTART[22] ,Channel 22 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 21. " HSTART[21] ,Channel 21 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 20. " HSTART[20] ,Channel 20 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 19. " HSTART[19] ,Channel 19 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 18. " HSTART[18] ,Channel 18 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 17. " HSTART[17] ,Channel 17 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 16. " HSTART[16] ,Channel 16 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 15. " HSTART[15] ,Channel 15 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 14. " HSTART[14] ,Channel 14 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 13. " HSTART[13] ,Channel 13 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 12. " HSTART[12] ,Channel 12 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 11. " HSTART[11] ,Channel 11 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 10. " HSTART[10] ,Channel 10 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 9. " HSTART[9] ,Channel 9 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 8. " HSTART[8] ,Channel 8 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 7. " HSTART[7] ,Channel 7 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 6. " HSTART[6] ,Channel 6 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 5. " HSTART[5] ,Channel 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 4. " HSTART[4] ,Channel 4 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 3. " HSTART[3] ,Channel 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 2. " HSTART[2] ,Channel 2 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0C 1. " HSTART[1] ,Channel 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0C 0. " HSTART[0] ,Channel 0 Enable" "Disabled,Enabled"
|
|
line.long 0x10 "EVTOVR,Channel Event Override Register"
|
|
bitfld.long 0x10 31. " EO[31] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 30. " EO[30] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 29. " EO[29] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 28. " EO[28] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 27. " EO[27] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 26. " EO[26] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 25. " EO[25] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 24. " EO[24] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 23. " EO[23] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 22. " EO[22] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 21. " EO[21] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 20. " EO[20] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 19. " EO[19] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 18. " EO[18] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 17. " EO[17] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 16. " EO[16] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 15. " EO[15] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 14. " EO[14] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 13. " EO[13] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 12. " EO[12] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 11. " EO[11] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 10. " EO[10] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 9. " EO[9] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 8. " EO[8] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 7. " EO[7] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 6. " EO[6] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 5. " EO[5] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 4. " EO[4] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 3. " EO[3] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 2. " EO[2] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x10 1. " EO[1] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x10 0. " EO[0] ,DMA Request Ignored by SDMA" "Not ignored,Ignored"
|
|
group.long 0x18++0x3
|
|
line.long 0x00 "HOSTOVR,Channel AP Override Register"
|
|
bitfld.long 0x00 31. " HO[31] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 30. " HO[30] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 29. " HO[29] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 28. " HO[28] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 27. " HO[27] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 26. " HO[26] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 25. " HO[25] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 24. " HO[24] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 23. " HO[23] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 22. " HO[22] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 21. " HO[21] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 20. " HO[20] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 19. " HO[19] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 18. " HO[18] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 17. " HO[17] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 16. " HO[16] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 15. " HO[15] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 14. " HO[14] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 13. " HO[13] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 12. " HO[12] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 11. " HO[11] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 10. " HO[10] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 9. " HO[9] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 8. " HO[8] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 7. " HO[7] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 6. " HO[6] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 5. " HO[5] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 4. " HO[4] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 3. " HO[3] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 2. " HO[2] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
textline " "
|
|
bitfld.long 0x00 1. " HO[1] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
bitfld.long 0x00 0. " HO[0] ,AP Enable Ignored by SDMA" "Not ignored,Ignored"
|
|
rgroup.long 0x1C++0x3
|
|
line.long 0x00 "EVTPEND,Channel Event Pending Register"
|
|
bitfld.long 0x00 31. " EP[31] ,Channel 31 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 30. " EP[30] ,Channel 30 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 29. " EP[29] ,Channel 29 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 28. " EP[28] ,Channel 28 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 27. " EP[27] ,Channel 27 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 26. " EP[26] ,Channel 26 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 25. " EP[25] ,Channel 25 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 24. " EP[24] ,Channel 24 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 23. " EP[23] ,Channel 23 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 22. " EP[22] ,Channel 22 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 21. " EP[21] ,Channel 21 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 20. " EP[20] ,Channel 20 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 19. " EP[19] ,Channel 19 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 18. " EP[18] ,Channel 18 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 17. " EP[17] ,Channel 17 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 16. " EP[16] ,Channel 16 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 15. " EP[15] ,Channel 15 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 14. " EP[14] ,Channel 14 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 13. " EP[13] ,Channel 13 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 12. " EP[12] ,Channel 12 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 11. " EP[11] ,Channel 11 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 10. " EP[10] ,Channel 10 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 9. " EP[9] ,Channel 9 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 8. " EP[8] ,Channel 8 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EP[7] ,Channel 7 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 6. " EP[6] ,Channel 6 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 5. " EP[5] ,Channel 5 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 4. " EP[4] ,Channel 4 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 3. " EP[3] ,Channel 3 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 2. " EP[2] ,Channel 2 Event Pending" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 1. " EP[1] ,Channel 1 Event Pending" "Not pending,Pending"
|
|
bitfld.long 0x00 0. " EP[0] ,Channel 0 Event Pending" "Not pending,Pending"
|
|
rgroup.long 0x24++0x7
|
|
line.long 0x00 "RESET,Reset Register"
|
|
bitfld.long 0x00 1. " RESCHED ,SDMA Reschedule as If a Script had Executed a Done Instruction" "Off,On"
|
|
bitfld.long 0x00 0. " RESET ,Software Reset" "No effect,Reset"
|
|
line.long 0x04 "EVTERR,DMA Request Error Register"
|
|
bitfld.long 0x04 31. " CHNERR[31] ,Channel 31 Error" "No error,Error"
|
|
bitfld.long 0x04 30. " CHNERR[30] ,Channel 30 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 29. " CHNERR[29] ,Channel 29 Error" "No error,Error"
|
|
bitfld.long 0x04 28. " CHNERR[28] ,Channel 28 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 27. " CHNERR[27] ,Channel 27 Error" "No error,Error"
|
|
bitfld.long 0x04 26. " CHNERR[26] ,Channel 26 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 25. " CHNERR[25] ,Channel 25 Error" "No error,Error"
|
|
bitfld.long 0x04 24. " CHNERR[24] ,Channel 24 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 23. " CHNERR[23] ,Channel 23 Error" "No error,Error"
|
|
bitfld.long 0x04 22. " CHNERR[22] ,Channel 22 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 21. " CHNERR[21] ,Channel 21 Error" "No error,Error"
|
|
bitfld.long 0x04 20. " CHNERR[20] ,Channel 20 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 19. " CHNERR[19] ,Channel 19 Error" "No error,Error"
|
|
bitfld.long 0x04 18. " CHNERR[18] ,Channel 18 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 17. " CHNERR[17] ,Channel 17 Error" "No error,Error"
|
|
bitfld.long 0x04 16. " CHNERR[16] ,Channel 16 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 15. " CHNERR[15] ,Channel 15 Error" "No error,Error"
|
|
bitfld.long 0x04 14. " CHNERR[14] ,Channel 14 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 13. " CHNERR[13] ,Channel 13 Error" "No error,Error"
|
|
bitfld.long 0x04 12. " CHNERR[12] ,Channel 12 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 11. " CHNERR[11] ,Channel 11 Error" "No error,Error"
|
|
bitfld.long 0x04 10. " CHNERR[10] ,Channel 10 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 9. " CHNERR[9] ,Channel 9 Error" "No error,Error"
|
|
bitfld.long 0x04 8. " CHNERR[8] ,Channel 8 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 7. " CHNERR[7] ,Channel 7 Error" "No error,Error"
|
|
bitfld.long 0x04 6. " CHNERR[6] ,Channel 6 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 5. " CHNERR[5] ,Channel 5 Error" "No error,Error"
|
|
bitfld.long 0x04 4. " CHNERR[4] ,Channel 4 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 3. " CHNERR[3] ,Channel 3 Error" "No error,Error"
|
|
bitfld.long 0x04 2. " CHNERR[2] ,Channel 2 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 1. " CHNERR[1] ,Channel 1 Error" "No error,Error"
|
|
bitfld.long 0x04 0. " CHNERR[0] ,Channel 0 Error" "No error,Error"
|
|
group.long 0x2C++0x03
|
|
line.long 0x00 "INTRMASK,Channel AP Interrupt Mask Flags Register"
|
|
bitfld.long 0x00 31. " HIMASK[31] ,Channel 31 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 30. " HIMASK[30] ,Channel 30 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 29. " HIMASK[29] ,Channel 29 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 28. " HIMASK[28] ,Channel 28 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 27. " HIMASK[27] ,Channel 27 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 26. " HIMASK[26] ,Channel 26 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 25. " HIMASK[25] ,Channel 25 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 24. " HIMASK[24] ,Channel 24 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 23. " HIMASK[23] ,Channel 23 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 22. " HIMASK[22] ,Channel 22 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 21. " HIMASK[21] ,Channel 21 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 20. " HIMASK[20] ,Channel 20 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 19. " HIMASK[19] ,Channel 19 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 18. " HIMASK[18] ,Channel 18 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 17. " HIMASK[17] ,Channel 17 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 16. " HIMASK[16] ,Channel 16 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 15. " HIMASK[15] ,Channel 15 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 14. " HIMASK[14] ,Channel 14 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 13. " HIMASK[13] ,Channel 13 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 12. " HIMASK[12] ,Channel 12 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 11. " HIMASK[11] ,Channel 11 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 10. " HIMASK[10] ,Channel 10 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 9. " HIMASK[9] ,Channel 9 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 8. " HIMASK[8] ,Channel 8 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 7. " HIMASK[7] ,Channel 7 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 6. " HIMASK[6] ,Channel 6 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 5. " HIMASK[5] ,Channel 5 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 4. " HIMASK[4] ,Channel 4 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 3. " HIMASK[3] ,Channel 3 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 2. " HIMASK[2] ,Channel 2 Interrupt Mask" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 1. " HIMASK[1] ,Channel 1 Interrupt Mask" "Masked,Not masked"
|
|
bitfld.long 0x00 0. " HIMASK[0] ,Channel 0 Interrupt Mask" "Masked,Not masked"
|
|
rgroup.long 0x30++0x7
|
|
line.long 0x00 "PSW,Schedule Status Register"
|
|
bitfld.long 0x00 13.--15. " NCP[2:0] ,Next Channel Priority" "No running channel,1,2,3,4,5,6,7"
|
|
bitfld.long 0x00 8.--12. " NCR[4:0] ,Next Channel Register" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
bitfld.long 0x00 5.--7. " CCP[2:0] ,Current Channel Priority" "No running channel,1,2,3,4,5,6,7"
|
|
bitfld.long 0x00 0.--4. " CCR[4:0] ,Current Channel Register" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
line.long 0x04 "EVTERRDBG,DMA Request Error Register for Debug"
|
|
bitfld.long 0x04 31. " CHNERR[31] ,Channel 31 Error" "No error,Error"
|
|
bitfld.long 0x04 30. " CHNERR[30] ,Channel 30 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 29. " CHNERR[29] ,Channel 29 Error" "No error,Error"
|
|
bitfld.long 0x04 28. " CHNERR[28] ,Channel 28 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 27. " CHNERR[27] ,Channel 27 Error" "No error,Error"
|
|
bitfld.long 0x04 26. " CHNERR[26] ,Channel 26 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 25. " CHNERR[25] ,Channel 25 Error" "No error,Error"
|
|
bitfld.long 0x04 24. " CHNERR[24] ,Channel 24 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 23. " CHNERR[23] ,Channel 23 Error" "No error,Error"
|
|
bitfld.long 0x04 22. " CHNERR[22] ,Channel 22 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 21. " CHNERR[21] ,Channel 21 Error" "No error,Error"
|
|
bitfld.long 0x04 20. " CHNERR[20] ,Channel 20 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 19. " CHNERR[19] ,Channel 19 Error" "No error,Error"
|
|
bitfld.long 0x04 18. " CHNERR[18] ,Channel 18 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 17. " CHNERR[17] ,Channel 17 Error" "No error,Error"
|
|
bitfld.long 0x04 16. " CHNERR[16] ,Channel 16 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 15. " CHNERR[15] ,Channel 15 Error" "No error,Error"
|
|
bitfld.long 0x04 14. " CHNERR[14] ,Channel 14 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 13. " CHNERR[13] ,Channel 13 Error" "No error,Error"
|
|
bitfld.long 0x04 12. " CHNERR[12] ,Channel 12 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 11. " CHNERR[11] ,Channel 11 Error" "No error,Error"
|
|
bitfld.long 0x04 10. " CHNERR[10] ,Channel 10 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 9. " CHNERR[9] ,Channel 9 Error" "No error,Error"
|
|
bitfld.long 0x04 8. " CHNERR[8] ,Channel 8 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 7. " CHNERR[7] ,Channel 7 Error" "No error,Error"
|
|
bitfld.long 0x04 6. " CHNERR[6] ,Channel 6 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 5. " CHNERR[5] ,Channel 5 Error" "No error,Error"
|
|
bitfld.long 0x04 4. " CHNERR[4] ,Channel 4 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 3. " CHNERR[3] ,Channel 3 Error" "No error,Error"
|
|
bitfld.long 0x04 2. " CHNERR[2] ,Channel 2 Error" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 1. " CHNERR[1] ,Channel 1 Error" "No error,Error"
|
|
bitfld.long 0x04 0. " CHNERR[0] ,Channel 0 Error" "No error,Error"
|
|
group.long 0x38++0x13
|
|
line.long 0x00 "CONFIG,Configuration Register"
|
|
bitfld.long 0x00 11. " RTDOBS ,Real-Time Debug Pins are Used" "Not used,Used"
|
|
bitfld.long 0x00 4. " ACR ,AHB/SDMA Core Clock Ratio" "2x core freq,Core freq"
|
|
textline " "
|
|
bitfld.long 0x00 0.--1. " CSM ,Selects the Context Switch Mode" "Static,Dynamic low power,Dynamic with no loop,Dynamic"
|
|
line.long 0x04 "SDMA_LOCK,SDMA Lock Register"
|
|
bitfld.long 0x04 0. " LOCK ,LOCK access to update SDMA" "Not locked,Locked"
|
|
bitfld.long 0x04 1. " SRESET_LOCK_CLR ,LOCK bit cleared on a software reset" "Not cleared,Cleared"
|
|
line.long 0x08 "ONCE_ENB,OnCE Enable Register"
|
|
bitfld.long 0x08 0. " ENB ,OnCE Enable" "Disabled,Enabled"
|
|
line.long 0x0c "ONCE_DATA,OnCE Data Register"
|
|
line.long 0x10 "ONCE_INSTR,OnCE Instruction Register"
|
|
hexmask.long.word 0x10 0.--15. 1. " INSTR ,Instruction Register of the OnCE JTAG Controller"
|
|
rgroup.long 0x4c++0x03
|
|
line.long 0x00 "ONCE_STAT,OnCE Status Register"
|
|
bitfld.long 0x00 12.--15. " PST[3:0] ,Processor Status" "Program,Data,Change of flow,Change of flow in loop,Debug,Functional unit,Sleep,Save,Program in sleep,Data in sleep,Change of flow in sleep,Change flow in loop in sleep,Debug in sleep,Functional unit in sleep,Sleep after reset,Restore"
|
|
bitfld.long 0x00 11. " RCV ,RCV Flag" "Cleared,Set"
|
|
textline " "
|
|
bitfld.long 0x00 10. " EDR ,SDMA has Entered Debug Mode After an External Debug Request" "Normal,Debug"
|
|
bitfld.long 0x00 9. " ODR ,SDMA has Entered Debug Mode After a OnCE Debug Request" "Normal,Debug"
|
|
textline " "
|
|
bitfld.long 0x00 8. " SWB ,SDMA has Entered Debug Mode After a Software Breakpoint" "Normal,Degug"
|
|
bitfld.long 0x00 7. " MST ,OnCE is Controlled from the AP Peripheral Interface" "JTAG,AP"
|
|
textline " "
|
|
bitfld.long 0x00 2. " EDR[2] ,Event Cell Debug Request from data_cond" "Not requested,Requested"
|
|
bitfld.long 0x00 1. " EDR[1] ,Event Cell Debug Request from addrb_cond" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 0. " EDR[0] ,Event Cell Debug Request from addra_cond" "Not requested,Requested"
|
|
group.long 0x50++0x03
|
|
line.long 0x00 "ONCE_CMD,OnCE Command Register"
|
|
bitfld.long 0x00 0.--3. " CMD ,Command" "rstatus,dmov,exec_once,run_core,exec_core,debug_rqst,rbuffer,?..."
|
|
group.long 0x58++0x7
|
|
line.long 0x00 "ILLINSTADDR,Illegal Instruction Trap Address Register"
|
|
hexmask.long.word 0x00 0.--13. 1. " ILLINSTADDR ,Illegal Instruction Trap Address"
|
|
line.long 0x04 "CHN0ADDR,Channel 0 Boot Address Register"
|
|
bitfld.long 0x04 14. " SMSZ ,Scratch Memory Size" "24,32"
|
|
hexmask.long.word 0x04 0.--13. 1. " CHN0ADDR ,Channel 0 Boot Address"
|
|
rgroup.long 0x60++0x07
|
|
line.long 0x00 "EVT_MIRROR,DMA Requests Register"
|
|
bitfld.long 0x00 31. " EVENTS[31] ,DMA Request ECT" "Not pending,Pending"
|
|
bitfld.long 0x00 30. " EVENTS[30] ,DMA Request NANDFC" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 29. " EVENTS[29] ,DMA Request SSI-1 RX0" "Not pending,Pending"
|
|
bitfld.long 0x00 28. " EVENTS[28] ,DMA Request SSI-1 RX0" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 27. " EVENTS[27] ,DMA Request SSI-1 TX1" "Not pending,Pending"
|
|
bitfld.long 0x00 26. " EVENTS[26] ,DMA Request SSI-1 RX1" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 25. " EVENTS[25] ,DMA Request SSI-2 TX0" "Not pending,Pending"
|
|
bitfld.long 0x00 24. " EVENTS[24] ,DMA Request SSI-2 RX0" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 23. " EVENTS[23] ,DMA Request SSI-2 TX1" "Not pending,Pending"
|
|
bitfld.long 0x00 22. " EVENTS[22] ,DMA Request SSI-2 RX1" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 21. " EVENTS[21] ,DMA Request IPU" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 19. " EVENTS[19] ,DMA Request UART-1 TX" "Not pending,Pending"
|
|
bitfld.long 0x00 18. " EVENTS[18] ,DMA Request UART-1 RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 17. " EVENTS[17] ,DMA Request UART-2 TX" "Not pending,Pending"
|
|
bitfld.long 0x00 16. " EVENTS[16] ,DMA Request UART-2 RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 15. " EVENTS[15] ,DMA Request EXT DMA 2" "Not pending,Pending"
|
|
bitfld.long 0x00 14. " EVENTS[14] ,DMA Request EXT DMA 1" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 13. " EVENTS[13] ,DMA Request SPDIF TX" "Not pending,Pending"
|
|
bitfld.long 0x00 12. " EVENTS[12] ,DMA Request SPDIF RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 11. " EVENTS[11] ,DMA Request UART-3 TX" "Not pending,Pending"
|
|
bitfld.long 0x00 10. " EVENTS[10] ,DMA Request UART-3 RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 9. " EVENTS[9] ,DMA Request CSPI-1 TX" "Not pending,Pending"
|
|
bitfld.long 0x00 8. " EVENTS[8] ,DMA Request CSP-1 RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 7. " EVENTS[7] ,DMA Request CSPI-2 TX" "Not pending,Pending"
|
|
bitfld.long 0x00 6. " EVENTS[6] ,DMA Request CSP-2 RX" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 5. " EVENTS[5] ,DMA Request MSHC" "Not pending,Pending"
|
|
bitfld.long 0x00 4. " EVENTS[4] ,DMA Request ATA RX FIFO" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 3. " EVENTS[3] ,DMA Request ATA TX FIFO" "Not pending,Pending"
|
|
bitfld.long 0x00 2. " EVENTS[2] ,DMA Request ATA TXFER end" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x00 1. " EVENTS[1] ,DMA Request DPTC/DVFS" "Not pending,Pending"
|
|
bitfld.long 0x00 0. " EVENTS[0] ,DMA Request EXT DMA 0" "Not pending,Pending"
|
|
line.long 0x04 "EVT_MIRROR2,DMA Requests 2 Register"
|
|
bitfld.long 0x04 15. " EVENTS[47] ,DMA Request ASRC DMA12" "Not pending,Pending"
|
|
bitfld.long 0x04 14. " EVENTS[46] ,DMA Request ASRC DMA11" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 13. " EVENTS[45] ,DMA Request ASRC DMA10" "Not pending,Pending"
|
|
bitfld.long 0x04 12. " EVENTS[44] ,DMA Request ASRC DMA9" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 11. " EVENTS[43] ,DMA Request ASRC DMA8" "Not pending,Pending"
|
|
bitfld.long 0x04 10. " EVENTS[42] ,DMA Request ASRC DMA7" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 9. " EVENTS[41] ,DMA Request ASRC DMA6" "Not pending,Pending"
|
|
bitfld.long 0x04 8. " EVENTS[40] ,DMA Request ASRC DMA5" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 7. " EVENTS[39] ,DMA Request ASRC DMA4" "Not pending,Pending"
|
|
bitfld.long 0x04 6. " EVENTS[38] ,DMA Request ASRC DMA3" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 5. " EVENTS[37] ,DMA Request ASRC DMA2" "Not pending,Pending"
|
|
bitfld.long 0x04 4. " EVENTS[36] ,DMA Request ASRC DMA1" "Not pending,Pending"
|
|
textline " "
|
|
bitfld.long 0x04 1. " EVENTS[33] ,DMA Request ESAI TX" "Not pending,Pending"
|
|
bitfld.long 0x04 0. " EVENTS[32] ,DMA Request ESAI RX" "Not pending,Pending"
|
|
group.long 0x70++0x7
|
|
line.long 0x00 "XTRIG_CONF1,Cross-Trigger Events Configuration Register 1"
|
|
bitfld.long 0x00 30. " CNF3 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x00 24.--29. " NUM3[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x00 22. " CNF2 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x00 16.--21. " NUM2[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x00 14. " CNF1 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x00 8.--13. " NUM1[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x00 6. " CNF0 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x00 0.--5. " NUM0[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
line.long 0x04 "XTRIG_CONF2,Cross-Trigger Events Configuration Register 2"
|
|
bitfld.long 0x04 30. " CNF7 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x04 24.--29. " NUM7[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x04 22. " CNF6 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x04 16.--21. " NUM6[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x04 14. " CNF5 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x04 8.--13. " NUM5[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x04 6. " CNF4 ,Configuration of the SDMA" "Channel,DMA request"
|
|
bitfld.long 0x04 0.--5. " NUM4[5:0] ,Number of the DMA Request" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
width 11.
|
|
tree "Channel Enable RAM Registers"
|
|
group.long 0x200++0x4f
|
|
line.long 0x0 "CHNENBL0 ,Channel 0 Enable RAM"
|
|
bitfld.long 0x0 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 0 " "Disabled,Enabled"
|
|
line.long 0x4 "CHNENBL1 ,Channel 1 Enable RAM"
|
|
bitfld.long 0x4 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
bitfld.long 0x4 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 1 " "Disabled,Enabled"
|
|
line.long 0x8 "CHNENBL2 ,Channel 2 Enable RAM"
|
|
bitfld.long 0x8 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
bitfld.long 0x8 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 2 " "Disabled,Enabled"
|
|
line.long 0xC "CHNENBL3 ,Channel 3 Enable RAM"
|
|
bitfld.long 0xC 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
bitfld.long 0xC 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 3 " "Disabled,Enabled"
|
|
line.long 0x10 "CHNENBL4 ,Channel 4 Enable RAM"
|
|
bitfld.long 0x10 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
bitfld.long 0x10 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 4 " "Disabled,Enabled"
|
|
line.long 0x14 "CHNENBL5 ,Channel 5 Enable RAM"
|
|
bitfld.long 0x14 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
bitfld.long 0x14 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 5 " "Disabled,Enabled"
|
|
line.long 0x18 "CHNENBL6 ,Channel 6 Enable RAM"
|
|
bitfld.long 0x18 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
bitfld.long 0x18 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 6 " "Disabled,Enabled"
|
|
line.long 0x1C "CHNENBL7 ,Channel 7 Enable RAM"
|
|
bitfld.long 0x1C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
bitfld.long 0x1C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 7 " "Disabled,Enabled"
|
|
line.long 0x20 "CHNENBL8 ,Channel 8 Enable RAM"
|
|
bitfld.long 0x20 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
bitfld.long 0x20 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 8 " "Disabled,Enabled"
|
|
line.long 0x24 "CHNENBL9 ,Channel 9 Enable RAM"
|
|
bitfld.long 0x24 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
bitfld.long 0x24 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 9 " "Disabled,Enabled"
|
|
line.long 0x28 "CHNENBL10,Channel 10 Enable RAM"
|
|
bitfld.long 0x28 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
bitfld.long 0x28 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 10" "Disabled,Enabled"
|
|
line.long 0x2C "CHNENBL11,Channel 11 Enable RAM"
|
|
bitfld.long 0x2C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
bitfld.long 0x2C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 11" "Disabled,Enabled"
|
|
line.long 0x30 "CHNENBL12,Channel 12 Enable RAM"
|
|
bitfld.long 0x30 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
bitfld.long 0x30 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 12" "Disabled,Enabled"
|
|
line.long 0x34 "CHNENBL13,Channel 13 Enable RAM"
|
|
bitfld.long 0x34 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x34 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
bitfld.long 0x34 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 13" "Disabled,Enabled"
|
|
line.long 0x38 "CHNENBL14,Channel 14 Enable RAM"
|
|
bitfld.long 0x38 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x38 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
bitfld.long 0x38 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 14" "Disabled,Enabled"
|
|
line.long 0x3C "CHNENBL15,Channel 15 Enable RAM"
|
|
bitfld.long 0x3C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x3C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
bitfld.long 0x3C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 15" "Disabled,Enabled"
|
|
line.long 0x40 "CHNENBL16,Channel 16 Enable RAM"
|
|
bitfld.long 0x40 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x40 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
bitfld.long 0x40 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 16" "Disabled,Enabled"
|
|
line.long 0x44 "CHNENBL17,Channel 17 Enable RAM"
|
|
bitfld.long 0x44 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x44 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
bitfld.long 0x44 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 17" "Disabled,Enabled"
|
|
line.long 0x48 "CHNENBL18,Channel 18 Enable RAM"
|
|
bitfld.long 0x48 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x48 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
bitfld.long 0x48 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 18" "Disabled,Enabled"
|
|
line.long 0x4C "CHNENBL19,Channel 19 Enable RAM"
|
|
bitfld.long 0x4C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
bitfld.long 0x4C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 19" "Disabled,Enabled"
|
|
group.long 0x254++0x33
|
|
line.long 0x0 "CHNENBL21,Channel 21 Enable RAM"
|
|
bitfld.long 0x0 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 21" "Disabled,Enabled"
|
|
line.long 0x4 "CHNENBL22,Channel 22 Enable RAM"
|
|
bitfld.long 0x4 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
bitfld.long 0x4 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 22" "Disabled,Enabled"
|
|
line.long 0x8 "CHNENBL23,Channel 23 Enable RAM"
|
|
bitfld.long 0x8 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
bitfld.long 0x8 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 23" "Disabled,Enabled"
|
|
line.long 0xC "CHNENBL24,Channel 24 Enable RAM"
|
|
bitfld.long 0xC 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
bitfld.long 0xC 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 24" "Disabled,Enabled"
|
|
line.long 0x10 "CHNENBL25,Channel 25 Enable RAM"
|
|
bitfld.long 0x10 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
bitfld.long 0x10 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 25" "Disabled,Enabled"
|
|
line.long 0x14 "CHNENBL26,Channel 26 Enable RAM"
|
|
bitfld.long 0x14 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
bitfld.long 0x14 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 26" "Disabled,Enabled"
|
|
line.long 0x18 "CHNENBL27,Channel 27 Enable RAM"
|
|
bitfld.long 0x18 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x18 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
bitfld.long 0x18 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 27" "Disabled,Enabled"
|
|
line.long 0x1C "CHNENBL28,Channel 28 Enable RAM"
|
|
bitfld.long 0x1C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x1C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
bitfld.long 0x1C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 28" "Disabled,Enabled"
|
|
line.long 0x20 "CHNENBL29,Channel 29 Enable RAM"
|
|
bitfld.long 0x20 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x20 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
bitfld.long 0x20 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 29" "Disabled,Enabled"
|
|
line.long 0x24 "CHNENBL30,Channel 30 Enable RAM"
|
|
bitfld.long 0x24 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x24 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
bitfld.long 0x24 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 30" "Disabled,Enabled"
|
|
line.long 0x28 "CHNENBL31,Channel 31 Enable RAM"
|
|
bitfld.long 0x28 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x28 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
bitfld.long 0x28 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 31" "Disabled,Enabled"
|
|
line.long 0x2C "CHNENBL32,Channel 32 Enable RAM"
|
|
bitfld.long 0x2C 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x2C 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
bitfld.long 0x2C 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 32" "Disabled,Enabled"
|
|
line.long 0x30 "CHNENBL33,Channel 33 Enable RAM"
|
|
bitfld.long 0x30 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x30 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
bitfld.long 0x30 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 33" "Disabled,Enabled"
|
|
group.long 0x290++0x17
|
|
line.long 0x0 "CHNENBL36,Channel 36 Enable RAM"
|
|
bitfld.long 0x0 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 36" "Disabled,Enabled"
|
|
line.long 0x4 "CHNENBL37,Channel 37 Enable RAM"
|
|
bitfld.long 0x4 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
bitfld.long 0x4 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 37" "Disabled,Enabled"
|
|
line.long 0x8 "CHNENBL38,Channel 38 Enable RAM"
|
|
bitfld.long 0x8 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
bitfld.long 0x8 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 38" "Disabled,Enabled"
|
|
line.long 0xC "CHNENBL39,Channel 39 Enable RAM"
|
|
bitfld.long 0xC 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
bitfld.long 0xC 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 39" "Disabled,Enabled"
|
|
line.long 0x10 "CHNENBL40,Channel 40 Enable RAM"
|
|
bitfld.long 0x10 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
bitfld.long 0x10 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 40" "Disabled,Enabled"
|
|
line.long 0x14 "CHNENBL41,Channel 41 Enable RAM"
|
|
bitfld.long 0x14 31. " ENBL[31] ,Channel 31 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 30. " ENBL[30] ,Channel 30 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 29. " ENBL[29] ,Channel 29 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 28. " ENBL[28] ,Channel 28 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 27. " ENBL[27] ,Channel 27 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 26. " ENBL[26] ,Channel 26 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 25. " ENBL[25] ,Channel 25 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 24. " ENBL[24] ,Channel 24 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 23. " ENBL[23] ,Channel 23 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 22. " ENBL[22] ,Channel 22 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 21. " ENBL[21] ,Channel 21 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 20. " ENBL[20] ,Channel 20 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 19. " ENBL[19] ,Channel 19 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 18. " ENBL[18] ,Channel 18 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 17. " ENBL[17] ,Channel 17 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 16. " ENBL[16] ,Channel 16 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 15. " ENBL[15] ,Channel 15 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 14. " ENBL[14] ,Channel 14 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 13. " ENBL[13] ,Channel 13 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 12. " ENBL[12] ,Channel 12 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 11. " ENBL[11] ,Channel 11 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 10. " ENBL[10] ,Channel 10 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 9. " ENBL[09] ,Channel 9 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 8. " ENBL[08] ,Channel 8 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 7. " ENBL[07] ,Channel 7 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 6. " ENBL[06] ,Channel 6 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 5. " ENBL[05] ,Channel 5 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 4. " ENBL[04] ,Channel 4 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x14 3. " ENBL[03] ,Channel 3 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 2. " ENBL[02] ,Channel 2 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 1. " ENBL[01] ,Channel 1 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
bitfld.long 0x14 0. " ENBL[00] ,Channel 0 Enable triggered by DMA request number 41" "Disabled,Enabled"
|
|
tree.end
|
|
width 10.
|
|
tree "Channel Priority Registers"
|
|
group.long 0x100++0x7f
|
|
line.long 0x0 "CHNPRI0 ,Channel 0 Priority Register"
|
|
bitfld.long 0x0 0.--2. " CHNPRI0 ,Priority of Channel Number 0 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x4 "CHNPRI1 ,Channel 1 Priority Register"
|
|
bitfld.long 0x4 0.--2. " CHNPRI1 ,Priority of Channel Number 1 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x8 "CHNPRI2 ,Channel 2 Priority Register"
|
|
bitfld.long 0x8 0.--2. " CHNPRI2 ,Priority of Channel Number 2 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0xC "CHNPRI3 ,Channel 3 Priority Register"
|
|
bitfld.long 0xC 0.--2. " CHNPRI3 ,Priority of Channel Number 3 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x10 "CHNPRI4 ,Channel 4 Priority Register"
|
|
bitfld.long 0x10 0.--2. " CHNPRI4 ,Priority of Channel Number 4 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x14 "CHNPRI5 ,Channel 5 Priority Register"
|
|
bitfld.long 0x14 0.--2. " CHNPRI5 ,Priority of Channel Number 5 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x18 "CHNPRI6 ,Channel 6 Priority Register"
|
|
bitfld.long 0x18 0.--2. " CHNPRI6 ,Priority of Channel Number 6 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x1C "CHNPRI7 ,Channel 7 Priority Register"
|
|
bitfld.long 0x1C 0.--2. " CHNPRI7 ,Priority of Channel Number 7 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x20 "CHNPRI8 ,Channel 8 Priority Register"
|
|
bitfld.long 0x20 0.--2. " CHNPRI8 ,Priority of Channel Number 8 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x24 "CHNPRI9 ,Channel 9 Priority Register"
|
|
bitfld.long 0x24 0.--2. " CHNPRI9 ,Priority of Channel Number 9 " "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x28 "CHNPRI10,Channel 10 Priority Register"
|
|
bitfld.long 0x28 0.--2. " CHNPRI10 ,Priority of Channel Number 10" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x2C "CHNPRI11,Channel 11 Priority Register"
|
|
bitfld.long 0x2C 0.--2. " CHNPRI11 ,Priority of Channel Number 11" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x30 "CHNPRI12,Channel 12 Priority Register"
|
|
bitfld.long 0x30 0.--2. " CHNPRI12 ,Priority of Channel Number 12" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x34 "CHNPRI13,Channel 13 Priority Register"
|
|
bitfld.long 0x34 0.--2. " CHNPRI13 ,Priority of Channel Number 13" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x38 "CHNPRI14,Channel 14 Priority Register"
|
|
bitfld.long 0x38 0.--2. " CHNPRI14 ,Priority of Channel Number 14" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x3C "CHNPRI15,Channel 15 Priority Register"
|
|
bitfld.long 0x3C 0.--2. " CHNPRI15 ,Priority of Channel Number 15" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x40 "CHNPRI16,Channel 16 Priority Register"
|
|
bitfld.long 0x40 0.--2. " CHNPRI16 ,Priority of Channel Number 16" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x44 "CHNPRI17,Channel 17 Priority Register"
|
|
bitfld.long 0x44 0.--2. " CHNPRI17 ,Priority of Channel Number 17" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x48 "CHNPRI18,Channel 18 Priority Register"
|
|
bitfld.long 0x48 0.--2. " CHNPRI18 ,Priority of Channel Number 18" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x4C "CHNPRI19,Channel 19 Priority Register"
|
|
bitfld.long 0x4C 0.--2. " CHNPRI19 ,Priority of Channel Number 19" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x50 "CHNPRI20,Channel 20 Priority Register"
|
|
bitfld.long 0x50 0.--2. " CHNPRI20 ,Priority of Channel Number 20" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x54 "CHNPRI21,Channel 21 Priority Register"
|
|
bitfld.long 0x54 0.--2. " CHNPRI21 ,Priority of Channel Number 21" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x58 "CHNPRI22,Channel 22 Priority Register"
|
|
bitfld.long 0x58 0.--2. " CHNPRI22 ,Priority of Channel Number 22" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x5C "CHNPRI23,Channel 23 Priority Register"
|
|
bitfld.long 0x5C 0.--2. " CHNPRI23 ,Priority of Channel Number 23" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x60 "CHNPRI24,Channel 24 Priority Register"
|
|
bitfld.long 0x60 0.--2. " CHNPRI24 ,Priority of Channel Number 24" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x64 "CHNPRI25,Channel 25 Priority Register"
|
|
bitfld.long 0x64 0.--2. " CHNPRI25 ,Priority of Channel Number 25" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x68 "CHNPRI26,Channel 26 Priority Register"
|
|
bitfld.long 0x68 0.--2. " CHNPRI26 ,Priority of Channel Number 26" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x6C "CHNPRI27,Channel 27 Priority Register"
|
|
bitfld.long 0x6C 0.--2. " CHNPRI27 ,Priority of Channel Number 27" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x70 "CHNPRI28,Channel 28 Priority Register"
|
|
bitfld.long 0x70 0.--2. " CHNPRI28 ,Priority of Channel Number 28" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x74 "CHNPRI29,Channel 29 Priority Register"
|
|
bitfld.long 0x74 0.--2. " CHNPRI29 ,Priority of Channel Number 29" "No running channel,1,2,3,4,5,6,7"
|
|
line.long 0x78 "CHNPRI30,Channel 30 Priority Register"
|
|
bitfld.long 0x78 0.--2. " CHNPRI30 ,Priority of Channel Number 30" "No running channel,1,2,3,4,5,6,7"
|
|
tree.end
|
|
width 14.
|
|
tree.end
|
|
tree "SPBA (Shared Peripheral Bus Arbiter)"
|
|
base ad:0x5003C000
|
|
width 7.
|
|
tree "Peripheral Right Register 0-15"
|
|
group.long 0x00++0x3F
|
|
line.long 0x0 "PRR0,Peripheral Right Register 0"
|
|
bitfld.long 0x0 30.--31. " RMO0 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x0 16.--17. " ROI0 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x0 2. " RAR02 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x0 1. " RAR01 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x0 0. " RAR00 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x4 "PRR1,Peripheral Right Register 1"
|
|
bitfld.long 0x4 30.--31. " RMO1 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x4 16.--17. " ROI1 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x4 2. " RAR12 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x4 1. " RAR11 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x4 0. " RAR10 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x8 "PRR2,Peripheral Right Register 2"
|
|
bitfld.long 0x8 30.--31. " RMO2 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x8 16.--17. " ROI2 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x8 2. " RAR22 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x8 1. " RAR21 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x8 0. " RAR20 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0xC "PRR3,Peripheral Right Register 3"
|
|
bitfld.long 0xC 30.--31. " RMO3 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0xC 16.--17. " ROI3 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0xC 2. " RAR32 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0xC 1. " RAR31 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0xC 0. " RAR30 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x10 "PRR4,Peripheral Right Register 4"
|
|
bitfld.long 0x10 30.--31. " RMO4 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x10 16.--17. " ROI4 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x10 2. " RAR42 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x10 1. " RAR41 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x10 0. " RAR40 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x14 "PRR5,Peripheral Right Register 5"
|
|
bitfld.long 0x14 30.--31. " RMO5 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x14 16.--17. " ROI5 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x14 2. " RAR52 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x14 1. " RAR51 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x14 0. " RAR50 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x18 "PRR6,Peripheral Right Register 6"
|
|
bitfld.long 0x18 30.--31. " RMO6 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x18 16.--17. " ROI6 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x18 2. " RAR62 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x18 1. " RAR61 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x18 0. " RAR60 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x1C "PRR7,Peripheral Right Register 7"
|
|
bitfld.long 0x1C 30.--31. " RMO7 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x1C 16.--17. " ROI7 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x1C 2. " RAR72 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x1C 1. " RAR71 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x1C 0. " RAR70 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x20 "PRR8,Peripheral Right Register 8"
|
|
bitfld.long 0x20 30.--31. " RMO8 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x20 16.--17. " ROI8 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x20 2. " RAR82 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x20 1. " RAR81 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x20 0. " RAR80 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x24 "PRR9,Peripheral Right Register 9"
|
|
bitfld.long 0x24 30.--31. " RMO9 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x24 16.--17. " ROI9 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x24 2. " RAR92 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x24 1. " RAR91 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x24 0. " RAR90 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x28 "PRR10,Peripheral Right Register 10"
|
|
bitfld.long 0x28 30.--31. " RMO10 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x28 16.--17. " ROI10 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x28 2. " RAR102 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x28 1. " RAR101 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x28 0. " RAR100 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x2C "PRR11,Peripheral Right Register 11"
|
|
bitfld.long 0x2C 30.--31. " RMO11 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x2C 16.--17. " ROI11 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x2C 2. " RAR112 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x2C 1. " RAR111 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x2C 0. " RAR110 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x30 "PRR12,Peripheral Right Register 12"
|
|
bitfld.long 0x30 30.--31. " RMO12 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x30 16.--17. " ROI12 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x30 2. " RAR122 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x30 1. " RAR121 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x30 0. " RAR120 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x34 "PRR13,Peripheral Right Register 13"
|
|
bitfld.long 0x34 30.--31. " RMO13 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x34 16.--17. " ROI13 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x34 2. " RAR132 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x34 1. " RAR131 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x34 0. " RAR130 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x38 "PRR14,Peripheral Right Register 14"
|
|
bitfld.long 0x38 30.--31. " RMO14 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x38 16.--17. " ROI14 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x38 2. " RAR142 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x38 1. " RAR141 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x38 0. " RAR140 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x3C "PRR15,Peripheral Right Register 15"
|
|
bitfld.long 0x3C 30.--31. " RMO15 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x3C 16.--17. " ROI15 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x3C 2. " RAR152 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x3C 1. " RAR151 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x3C 0. " RAR150 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
tree.end
|
|
tree "Peripheral Right Register 16-31"
|
|
group.long 0x40++0x3F
|
|
line.long 0x0 "PRR16,Peripheral Right Register 16"
|
|
bitfld.long 0x0 30.--31. " RMO16 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x0 16.--17. " ROI16 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x0 2. " RAR162 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x0 1. " RAR161 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x0 0. " RAR160 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x4 "PRR17,Peripheral Right Register 17"
|
|
bitfld.long 0x4 30.--31. " RMO17 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x4 16.--17. " ROI17 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x4 2. " RAR172 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x4 1. " RAR171 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x4 0. " RAR170 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x8 "PRR18,Peripheral Right Register 18"
|
|
bitfld.long 0x8 30.--31. " RMO18 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x8 16.--17. " ROI18 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x8 2. " RAR182 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x8 1. " RAR181 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x8 0. " RAR180 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0xC "PRR19,Peripheral Right Register 19"
|
|
bitfld.long 0xC 30.--31. " RMO19 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0xC 16.--17. " ROI19 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0xC 2. " RAR192 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0xC 1. " RAR191 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0xC 0. " RAR190 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x10 "PRR20,Peripheral Right Register 20"
|
|
bitfld.long 0x10 30.--31. " RMO20 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x10 16.--17. " ROI20 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x10 2. " RAR202 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x10 1. " RAR201 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x10 0. " RAR200 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x14 "PRR21,Peripheral Right Register 21"
|
|
bitfld.long 0x14 30.--31. " RMO21 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x14 16.--17. " ROI21 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x14 2. " RAR212 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x14 1. " RAR211 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x14 0. " RAR210 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x18 "PRR22,Peripheral Right Register 22"
|
|
bitfld.long 0x18 30.--31. " RMO22 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x18 16.--17. " ROI22 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x18 2. " RAR222 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x18 1. " RAR221 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x18 0. " RAR220 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x1C "PRR23,Peripheral Right Register 23"
|
|
bitfld.long 0x1C 30.--31. " RMO23 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x1C 16.--17. " ROI23 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x1C 2. " RAR232 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x1C 1. " RAR231 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x1C 0. " RAR230 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x20 "PRR24,Peripheral Right Register 24"
|
|
bitfld.long 0x20 30.--31. " RMO24 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x20 16.--17. " ROI24 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x20 2. " RAR242 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x20 1. " RAR241 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x20 0. " RAR240 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x24 "PRR25,Peripheral Right Register 25"
|
|
bitfld.long 0x24 30.--31. " RMO25 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x24 16.--17. " ROI25 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x24 2. " RAR252 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x24 1. " RAR251 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x24 0. " RAR250 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x28 "PRR26,Peripheral Right Register 26"
|
|
bitfld.long 0x28 30.--31. " RMO26 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x28 16.--17. " ROI26 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x28 2. " RAR262 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x28 1. " RAR261 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x28 0. " RAR260 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x2C "PRR27,Peripheral Right Register 27"
|
|
bitfld.long 0x2C 30.--31. " RMO27 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x2C 16.--17. " ROI27 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x2C 2. " RAR272 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x2C 1. " RAR271 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x2C 0. " RAR270 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x30 "PRR28,Peripheral Right Register 28"
|
|
bitfld.long 0x30 30.--31. " RMO28 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x30 16.--17. " ROI28 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x30 2. " RAR282 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x30 1. " RAR281 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x30 0. " RAR280 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x34 "PRR29,Peripheral Right Register 29"
|
|
bitfld.long 0x34 30.--31. " RMO29 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x34 16.--17. " ROI29 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x34 2. " RAR292 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x34 1. " RAR291 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x34 0. " RAR290 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x38 "PRR30,Peripheral Right Register 30"
|
|
bitfld.long 0x38 30.--31. " RMO30 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x38 16.--17. " ROI30 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x38 2. " RAR302 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x38 1. " RAR301 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x38 0. " RAR300 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
line.long 0x3C "PRR31,Peripheral Right Register 31"
|
|
bitfld.long 0x3C 30.--31. " RMO31 ,Requesting Master Owner" "Un-owned,Reserved,Another master,Requesting master"
|
|
bitfld.long 0x3C 16.--17. " ROI31 ,Resource Owner ID" "Un-owned,Master A,Master B,Master C"
|
|
bitfld.long 0x3C 2. " RAR312 ,Resource Access Right for Master C" "Not allowed,Granted"
|
|
textline " "
|
|
bitfld.long 0x3C 1. " RAR311 ,Resource Access Right for Master B" "Not allowed,Granted"
|
|
bitfld.long 0x3C 0. " RAR310 ,Resource Access Right for Master A" "Not allowed,Granted"
|
|
tree.end
|
|
width 0xb
|
|
tree.end
|
|
tree "AUDMUX (Digital Audio Mux)"
|
|
base ad:0x53fc4000
|
|
width 7.
|
|
group.long (0x00+0x0)++0x07 "Port 1"
|
|
line.long 0x00 "PTCR1,Port Timing Control Register 1"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR1,Port Data Control Register 1"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x8)++0x07 "Port 2"
|
|
line.long 0x00 "PTCR2,Port Timing Control Register 2"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR2,Port Data Control Register 2"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x10)++0x07 "Port 3"
|
|
line.long 0x00 "PTCR3,Port Timing Control Register 3"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR3,Port Data Control Register 3"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x18)++0x07 "Port 4"
|
|
line.long 0x00 "PTCR4,Port Timing Control Register 4"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR4,Port Data Control Register 4"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x20)++0x07 "Port 5"
|
|
line.long 0x00 "PTCR5,Port Timing Control Register 5"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR5,Port Data Control Register 5"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x28)++0x07 "Port 6"
|
|
line.long 0x00 "PTCR6,Port Timing Control Register 6"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR6,Port Data Control Register 6"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long (0x00+0x30)++0x07 "Port 7"
|
|
line.long 0x00 "PTCR7,Port Timing Control Register 7"
|
|
bitfld.long 0x00 31. " TFSDIR ,Transmit Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 30. " TFSEL[3] ,Transmit Frame Sync Select" "TxFS,RxFS"
|
|
bitfld.long 0x00 27.--29. " TFSEL[2:0] ,Transmit Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 26. " TCLKDIR ,Transmit Clock Direction Control" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x00 25. " TCSEL[3] ,Transmit Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 22.--24. " TCSEL[2:0] ,Transmit Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 21. " RFSDIR ,Receive Frame Sync Direction Control" "Input,Output"
|
|
bitfld.long 0x00 20. " RFSEL[3] ,Receive Frame Sync Select" "TxFS,RxFS"
|
|
textline " "
|
|
bitfld.long 0x00 17.--19. " RFSEL[2:0] ,Receive Frame Sync Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x00 16. " RCLKDIR ,Receive Clock Direction Control" "Input,Output"
|
|
bitfld.long 0x00 15. " RCSEL[3] ,Receive Clock Select" "TxClk,RxClk"
|
|
bitfld.long 0x00 12.--14. " RCSEL[2:0] ,Receive Clock Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
textline " "
|
|
bitfld.long 0x00 11. " SYN ,Synchronous/Asynchronous Select" "Asynchronous,Synchronous"
|
|
line.long 0x04 "PDCR7,Port Data Control Register 7"
|
|
bitfld.long 0x04 13.--15. " RXDSEL[2:0] ,Receive Data Select" "Port 1,Port 2,Port 3,Port 4,Port 5,Port 6,Port 7,?..."
|
|
bitfld.long 0x04 12. " TXRXEN ,Transmit/Receive Switch Enable" "No switch,Switch"
|
|
bitfld.long 0x04 8.--9. " MODE[1:0] ,Mode Select" "Normal,Internal Network,CE Bus Network,?..."
|
|
textline " "
|
|
bitfld.long 0x04 6. " INMMASK7 ,Internal Network Mode Mask 7" "Included,Excluded"
|
|
bitfld.long 0x04 5. " INMMASK6 ,Internal Network Mode Mask 6" "Included,Excluded"
|
|
bitfld.long 0x04 4. " INMMASK5 ,Internal Network Mode Mask 5" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INMMASK4 ,Internal Network Mode Mask 4" "Included,Excluded"
|
|
bitfld.long 0x04 2. " INMMASK3 ,Internal Network Mode Mask 3" "Included,Excluded"
|
|
bitfld.long 0x04 1. " INMMASK2 ,Internal Network Mode Mask 2" "Included,Excluded"
|
|
textline " "
|
|
bitfld.long 0x04 0. " INMMASK1 ,Internal Network Mode Mask 1" "Included,Excluded"
|
|
group.long 0x38++0x03 "CE Bus Network Mode Control"
|
|
line.long 0x00 "CNMCR,CE Bus Network Mode Control Register"
|
|
bitfld.long 0x00 18. " CEN ,CE Bus Enable" "Held low,Generated"
|
|
bitfld.long 0x00 17. " FSPOL ,Frame Sync Polarity Select" "0,1"
|
|
bitfld.long 0x00 16. " CLKPOL ,Clock Sync Polarity Select" "0,1"
|
|
hexmask.long.byte 0x00 8.--15. 1. " CNTHI[7:0] ,CE Bus Disable Signal High Period Count"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--7. 1. " CNTLOW[7:0] ,CE Bus Disable Signal Low Period Count"
|
|
width 0xb
|
|
tree.end
|
|
tree "ASRC (Asynchronous Sample Rate Converter)"
|
|
base ad:0x5002c000
|
|
width 0xb
|
|
group.long (0x00*0x4)++0x03
|
|
; line.tbyte 0x00 "ASRCTR,ASRC Control Register"
|
|
textline ""
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCTR ,ASRC Control Register"
|
|
bitfld.long 0x00 22. " ATSC ,ASRC Pair C Automatic Selection For Processing Options" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " ATSB ,ASRC Pair B Automatic Selection For Processing Options" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " ATSA ,ASRC Pair A Automatic Selection For Processing Options" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 17.--18. " USRC/IDRC ,Use Ideal Ratio for Pair C" "Reserved,Reserved,Internal measured ratio,Idea ratio"
|
|
textline " "
|
|
bitfld.long 0x00 15.--16. " USRB/IDRB ,Use Ideal Ratio for Pair B" "Reserved,Reserved,Internal measured ratio,Idea ratio"
|
|
bitfld.long 0x00 13.--14. " USRA/IDRA ,Use Ideal Ratio for Pair A" "Reserved,Reserved,Internal measured ratio,Idea ratio"
|
|
textline " "
|
|
eventfld.long 0x00 4. " SRST ,Software Reset" "No reset,Reset"
|
|
bitfld.long 0x00 3. " ASREC ,ASRC Enable C" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ASREB ,ASRC Enable B" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " ASREA ,ASRC Enable A" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " ASRCEN ,ASRC Enable" "Disabled,Enabled"
|
|
group.long (0x01*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIER,Interrupt Enable Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIER ,Interrupt Enable Register"
|
|
bitfld.long 0x00 7. " AFPWE ,FP in Wait State Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " AOLIE ,Overload Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " ADOEC ,Data Output C Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " ADOEB ,Data Output B Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " ADOEA ,Data Output A Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " ADIEC ,Data Input C Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " ADIEB ,Data Input B Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " ADIEA ,Data Input A Interrupt Enable" "Disabled,Enabled"
|
|
group.long (0x03*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCNCR ,Channel Number Configuration Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCNCR ,Channel Number Configuration Register"
|
|
bitfld.long 0x00 6.--8. " ANCC ,Number of C Channels" "0,2,4,6,8,10,?..."
|
|
bitfld.long 0x00 3.--5. " ANCB ,Number of B Channels" "0,2,4,6,8,10,?..."
|
|
bitfld.long 0x00 0.--2. " ANCA ,Number of A Channels" "0,2,4,6,8,10,?..."
|
|
group.long (0x04*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCFG ,Filter Configuration Status Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCFG ,Filter Configuration Status Register"
|
|
bitfld.long 0x00 23. " INIRQC ,Initialization for Conversion Pair C is served" "Not served,Served"
|
|
bitfld.long 0x00 22. " INIRQB ,Initialization for Conversion Pair B is served" "Not served,Served"
|
|
textline " "
|
|
bitfld.long 0x00 21. " INIRQA ,Initialization for Conversion Pair A is served" "Not served,Served"
|
|
bitfld.long 0x00 20. " NDPRC ,Not Use Default Parameters for RAM-stored Parameters For Conversion Pair C" "Used,Not used"
|
|
textline " "
|
|
bitfld.long 0x00 19. " NDPRB ,Not Use Default Parameters for RAM-stored Parameters For Conversion Pair B" "Used,Not used"
|
|
bitfld.long 0x00 18. " NDPRA ,Not Use Default Parameters for RAM-stored Parameters For Conversion Pair A" "Used,Not used"
|
|
textline " "
|
|
bitfld.long 0x00 16.--17. " POSTMODC ,Post-Processing Configuration for Conversion Pair C" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,?..."
|
|
bitfld.long 0x00 14.--15. " PREMODC ,Pre-Processing Configuration for Conversion Pair C" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,Passthrough"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " POSTMODB ,Post-Processing Configuration for Conversion Pair B" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,?..."
|
|
bitfld.long 0x00 10.--11. " PREMODB ,Pre-Processing Configuration for Conversion Pair B" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,Passthrough"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " POSTMODA ,Post-Processing Configuration for Conversion Pair A" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,?..."
|
|
bitfld.long 0x00 6.--7. " PREMODA ,Pre-Processing Configuration for Conversion Pair A" "Upsampling-by-2,Direct-Connection,Downsampling-by-2,Passthrough"
|
|
group.long (0x05*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCSR ,ASRC Clock Source Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCSR ,ASRC Clock Source Register"
|
|
bitfld.long 0x00 20.--23. " AOCSC ,Output Clock Source C" "ESAI Tx,SSI1 Tx,SSI2 Tx,Reserved,SPDIF Tx,MLB,Reserved,Reserved,ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,ASRCK1,ASRCK1,ASRCK1"
|
|
bitfld.long 0x00 16.--19. " AOCSB ,Output Clock Source B" "ESAI Tx,SSI1 Tx,SSI2 Tx,Reserved,SPDIF Tx,MLB,Reserved,Reserved,ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,ASRCK1,ASRCK1,ASRCK1"
|
|
bitfld.long 0x00 12.--15. " AOCSA ,Output Clock Source A" "ESAI Tx,SSI1 Tx,SSI2 Tx,Reserved,SPDIF Tx,MLB,Reserved,Reserved,ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,ASRCK1,ASRCK1,ASRCK1"
|
|
bitfld.long 0x00 8.--11. " AICSC ,Input Clock Source C" "ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,MLB,Reserved,ASRCK1,ESAI Tx,SSI1 Tx,SSI2 Tx,Rederved,SPDIF Tx,ASRCK1,ASRCK1,ASRCK1"
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " AICSB ,Input Clock Source B" "ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,MLB,Reserved,ASRCK1,ESAI Tx,SSI1 Tx,SSI2 Tx,Rederved,SPDIF Tx,ASRCK1,ASRCK1,ASRCK1"
|
|
bitfld.long 0x00 0.--3. " AICSA ,Input Clock Source A" "ESAI Rx,SSI1 Rx,SSI2 Rx,Reserved,SPDIF Rx,MLB,Reserved,ASRCK1,ESAI Tx,SSI1 Tx,SSI2 Tx,Rederved,SPDIF Tx,ASRCK1,ASRCK1,ASRCK1"
|
|
group.long (0x06*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCDR1,ASRC Clock Divider Registers 1"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCDR1 ,ASRC Clock Divider Registers 1"
|
|
bitfld.long 0x00 21.--23. " AOCDB ,Output Clock Divider B" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 18.--20. " AOCPB ,Output Clock Prescaler B Specify the prescaling factor of" "1,2,4,8,16,32,64,128"
|
|
bitfld.long 0x00 15.--17. " AOCDA ,Output Clock Divider A" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 12.--14. " AOCPA ,Output Clock Prescaler A" "1,2,4,8,16,32,64,128"
|
|
textline " "
|
|
bitfld.long 0x00 9.--11. " AICDB ,Input Clock Divider B" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 6.--8. " AICPB ,Input Clock Prescaler B" "1,2,4,8,16,32,64,128"
|
|
bitfld.long 0x00 3.--5. " AICDA ,Input Clock Divider A" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 0.--2. " AICPA ,Input Clock Prescaler A" "1,2,4,8,16,32,64,128"
|
|
group.long (0x07*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCDR2,Clock Divider Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCDR2 ,Clock Divider Register"
|
|
bitfld.long 0x00 9.--11. " AOCDC ,Output Clock Divider C" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 6.--8. " AOCPC ,Output Clock Prescaler C" "1,2,4,8,16,32,64,128"
|
|
bitfld.long 0x00 3.--5. " AICDC ,Input Clock Divider C" "/1,/2,/3,/4,/5,/6,/7,/8"
|
|
bitfld.long 0x00 0.--2. " AICPC ,Input Clock Prescaler C" "1,2,4,8,16,32,64,128"
|
|
rgroup.long (0x08*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRSTR,ASRC Status Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRSTR ,ASRC Status Register"
|
|
bitfld.long 0x00 21. " DSLCNT ,DSL Counter Input to FIFO ready" "In process,Stored"
|
|
bitfld.long 0x00 20. " ATQOL ,Taskque FIFO overload" "Not oveloaded,Oveloaded"
|
|
textline " "
|
|
bitfld.long 0x00 19. " AOOLC ,Pair C Output Task Overload" "Not oveloaded,Oveloaded"
|
|
bitfld.long 0x00 18. " AOOLB ,Pair B Output Task Overload" "Not oveloaded,Oveloaded"
|
|
textline " "
|
|
bitfld.long 0x00 17. " AOOLA ,Pair A Output Task Overload" "Not oveloaded,Oveloaded"
|
|
bitfld.long 0x00 16. " AIOLC ,Pair C Input Task Overload" "Not oveloaded,Oveloaded"
|
|
textline " "
|
|
bitfld.long 0x00 15. " AIOLB ,Pair B Input Task Overload" "Not oveloaded,Oveloaded"
|
|
bitfld.long 0x00 14. " AIOLA ,Pair A Input Task Overload" "Not oveloaded,Oveloaded"
|
|
textline " "
|
|
bitfld.long 0x00 13. " AODOC ,Output Data Buffer C is overflowed" "Not oveloaded,Oveloaded"
|
|
bitfld.long 0x00 12. " AODOB ,Output Data Buffer B is overflowed" "Not oveloaded,Oveloaded"
|
|
textline " "
|
|
bitfld.long 0x00 11. " AODOA ,Output Data Buffer A is overflowed" "Not oveloaded,Oveloaded"
|
|
bitfld.long 0x00 10. " AIDUC ,Input Data Buffer C is underflowed" "Not underflowed,Underflowed"
|
|
textline " "
|
|
bitfld.long 0x00 9. " AIDUB ,Input Data Buffer B is underflowed" "Not underflowed,Underflowed"
|
|
bitfld.long 0x00 8. " AIDUA ,Input Data Buffer A is underflowed" "Not underflowed,Underflowed"
|
|
textline " "
|
|
bitfld.long 0x00 7. " FPWT ,FP is in wait states" "Not wait state,Wait state"
|
|
bitfld.long 0x00 6. " AOLE ,Overload Error Flag" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 5. " AODFC ,Number of data in Output Data Buffer C is greater than threshold" "Less/Equal,Greater"
|
|
bitfld.long 0x00 4. " AODFB ,Number of data in Output Data Buffer B is greater than threshold" "Less/Equal,Greater"
|
|
textline " "
|
|
bitfld.long 0x00 3. " AODFA ,Number of data in Output Data Buffer A is greater than threshold" "Less/Equal,Greater"
|
|
bitfld.long 0x00 2. " AIDEC ,Number of data in Input Data Buffer C is less than threshold" "Greater/Equal,Less"
|
|
textline " "
|
|
bitfld.long 0x00 1. " AIDEB ,Number of data in Input Data Buffer B is less than threshold" "Greater/Equal,Less"
|
|
bitfld.long 0x00 0. " AIDEA ,Number of data in Input Data Buffer A is less than threshold" "Greater/Equal,Less"
|
|
group.long (0x10*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRPM1,Parameter Registers 1"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRPM1 ,Parameter Registers 1"
|
|
group.long (0x11*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRPM2,Parameter Registers 2"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRPM2 ,Parameter Registers 2"
|
|
group.long (0x12*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRPM3,Parameter Registers 3"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRPM3 ,Parameter Registers 3"
|
|
group.long (0x13*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRPM4,Parameter Registers 4"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRPM4 ,Parameter Registers 4"
|
|
group.long (0x14*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRPM5,Parameter Registers 5"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRPM5 ,Parameter Registers 5"
|
|
group.long (0x15*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRTFR1,ASRC Task queue FIFO Register 1"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRTFR1 ,ASRC Task queue FIFO Register 1"
|
|
hexmask.long.byte 0x00 13.--19. 1. " TF_FILL ,Display the fillings of task queue FIFO"
|
|
hexmask.long.byte 0x00 6.--12. 1. " TF_BASE ,Set and display the base address for task queue FIFO"
|
|
group.long (0x17*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRCCR,Channel Counter Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRCCR ,Channel Counter Register"
|
|
bitfld.long 0x00 20.--23. " ACOC ,The channel counter for Pair C's output FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
bitfld.long 0x00 16.--19. " ACOB ,The channel counter for Pair B's output FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " ACOA ,The channel counter for Pair A's output FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
bitfld.long 0x00 8.--11. " ACIC ,The channel counter for Pair C's input FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
textline " "
|
|
bitfld.long 0x00 4.--7. " ACIB ,The channel counter for Pair B's input FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
bitfld.long 0x00 0.--3. " ACIA ,The channel counter for Pair A's input FIFO" "0,1,2,3,4,5,6,7,8,9,?..."
|
|
group.long (0x20*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRHA,Ideal Ratio Registers for Pair A (High Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRHA ,Ideal Ratio Registers for Pair A (High Part)"
|
|
hexmask.long.byte 0x00 0.--7. 1. " IDRATIOA ,IDRATIOA"
|
|
group.long (0x21*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRLA,Ideal Ratio Registers for Pair A (Low Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRLA ,Ideal Ratio Registers for Pair A (Low Part)"
|
|
group.long (0x22*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRHB,Ideal Ratio Registers for Pair B(High Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRHB ,Ideal Ratio Registers for Pair B(High Part)"
|
|
hexmask.long.byte 0x00 0.--7. 1. " IDRATIOB ,IDRATIOB"
|
|
group.long (0x23*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRLB,Ideal Ratio Registers for Pair B(Low Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRLB ,Ideal Ratio Registers for Pair B(Low Part)"
|
|
group.long (0x24*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRHC,Ideal Ratio Registers for Pair C(High Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRHC ,Ideal Ratio Registers for Pair C(High Part)"
|
|
hexmask.long.byte 0x00 0.--7. 1. " IDRATIOC ,IDRATIOC"
|
|
group.long (0x25*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASRIDRLC,Ideal Ratio Registers for Pair C(Low Part)"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASRIDRLC ,Ideal Ratio Registers for Pair C(Low Part)"
|
|
group.long (0x26*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASR76K,ASRC 76KHz Period Register in Terms of Master Clock"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASR76K ,ASRC 76KHz Period Register in Terms of Master Clock"
|
|
hexmask.long.tbyte 0x00 0.--16. 1. " ASR76K ,ASR76K"
|
|
group.long (0x27*0x4)++0x03
|
|
textline ""
|
|
; line.tbyte 0x00 "ASR56K,ASRC 56KHz Period Register in Terms of Master Clock"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "ASR56K ,ASRC 56KHz Period Register in Terms of Master Clock"
|
|
hexmask.long.tbyte 0x00 0.--16. 1. " ASR56K ,ASR56K"
|
|
width 0xb
|
|
tree.end
|
|
tree "ESAI (Enhanced Synchronous Audio Interface)"
|
|
base ad:0x50034000
|
|
width 7.
|
|
wgroup.long 0x00++0x03
|
|
line.long 0x00 "ETDR,ESAI Transmit Data Register"
|
|
hgroup.long 0x04++0x03
|
|
hide.long 0x00 "ERDR,ESAI Receive Data Register"
|
|
in
|
|
group.long 0x08++0x03
|
|
line.long 0x00 "ECR,ESAI Control Register"
|
|
bitfld.long 0x00 19. " ETI ,EXTAL Transmitter In" "HCKT normal,EXTAL muxed into HCKT"
|
|
bitfld.long 0x00 18. " ETO ,EXTAL Transmitter Out" "HCKT normal,EXTAL driven onto HCKT"
|
|
textline " "
|
|
bitfld.long 0x00 17. " ERI ,EXTAL Receiver In" "HCKR normal,EXTAL muxed into HCKR"
|
|
bitfld.long 0x00 16. " ERO ,EXTAL Receiver Out" "HCKR normal,EXTAL driven onto HCKR"
|
|
textline " "
|
|
bitfld.long 0x00 1. " ERST ,ESAI Reset" "No reset,Reset"
|
|
bitfld.long 0x00 0. " ESAIEN ,ESAI Enable" "Disabled,Enabled"
|
|
rgroup.long 0x0c++0x03
|
|
line.long 0x00 "ESR,ESAI Status Register"
|
|
bitfld.long 0x00 10. " TINIT ,Transmit Initialization" "Finished,Not finished"
|
|
bitfld.long 0x00 9. " RFF ,Receive FIFO Full" "< Rx FIFO watermark,>= Rx FIFO watermark"
|
|
textline " "
|
|
bitfld.long 0x00 8. " TFE ,Transmit FIFO Empty" "< Tx FIFO watermark,>= Tx FIFO watermark"
|
|
bitfld.long 0x00 7. " TLS ,Transmit Last Slot" "Not highest priority,Highest priority"
|
|
bitfld.long 0x00 6. " TDE ,Transmit Data Exception" "Not highest priority,Highest priority"
|
|
textline " "
|
|
bitfld.long 0x00 5. " TED ,Transmit Even Data" "Not highest priority,Highest priority"
|
|
bitfld.long 0x00 4. " TD ,Transmit Data" "Not highest priority,Highest priority"
|
|
bitfld.long 0x00 3. " RLS ,Receive Last Slot" "Not highest priority,Highest priority"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RDE ,Receive Data Exception" "Not highest priority,Highest priority"
|
|
bitfld.long 0x00 1. " RED ,Receive Even Data" "Not highest priority,Highest priority"
|
|
bitfld.long 0x00 0. " RD ,Receive Data" "Not highest priority,Highest priority"
|
|
group.long 0x10++0x03
|
|
line.long 0x00 "TFCR,Transmit FIFO Configuration Register"
|
|
bitfld.long 0x00 16.--18. " TWA ,Transmit Word Alignment" "MSB=31 | 7:0 ignored,MSB=27 | 3:0 ignored,MSB=23,MSB=19 | bottom 4bits zeroed,MSB=15 | bottom 8bits zeroed,MSB=11 | bottom 12bits zeroed,MSB=7 | bottom 16bits zeroed,MSB=3 | bottom 20bits zeroed"
|
|
textline " "
|
|
bitfld.long 0x00 19. " TIEN ,Transmitter Initialization Enable" "Disabled,Enabled"
|
|
hexmask.long.byte 0x00 8.--15. 1. " TFWM ,Transmit FIFO Watermark"
|
|
textline " "
|
|
bitfld.long 0x00 7. " TE5 ,Transmitter #5 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " TE4 ,Transmitter #4 FIFO Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " TE3 ,Transmitter #3 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " TE2 ,Transmitter #2 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " TE1 ,Transmitter #1 FIFO Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TE0 ,Transmitter #0 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " TFR ,Transmit FIFO Reset" "No reset,Reset"
|
|
bitfld.long 0x00 0. " TFE ,Transmit FIFO Enable" "Disabled,Enabled"
|
|
rgroup.long 0x14++0x03
|
|
line.long 0x00 "TFSR,Transmit FIFO Status Register"
|
|
bitfld.long 0x00 12.--14. " NTFO ,Next Transmitter FIFO Out" "#0,#1,#2,#3,#4,#5,?..."
|
|
bitfld.long 0x00 8.--10. " NTFI ,Next Transmitter FIFO In" "#0,#1,#2,#3,#4,#5,?..."
|
|
hexmask.long.byte 0x00 0.--7. 1. " TFCNT ,Transmit FIFO Counter"
|
|
group.long 0x18++0x03
|
|
line.long 0x00 "RFCR,Receive FIFO Configuration Register"
|
|
bitfld.long 0x00 16.--18. " RWA ,Receive Word Alignment" "MSB=31 | 7-0 zeroed,MSB=27 | 3-0 zeroed,MSB=23,MSB=19 | 3-0 ignored,MSB=15 | 7-0 ignored,MSB=11 | 11-0 ignored,MSB=7 | 15-0 ignored,MSB=3 | 19-0 ignored"
|
|
textline " "
|
|
bitfld.long 0x00 19. " REXT ,Receive Extension" "Zero,Sign"
|
|
hexmask.long.byte 0x00 8.--15. 1. " RFWM ,Receive FIFO Watermark"
|
|
textline " "
|
|
bitfld.long 0x00 5. " RE3 ,Receiver #3 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " RE2 ,Receiver #2 FIFO Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " RE1 ,Receiver #1 FIFO Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " RE0 ,Receiver #0 FIFO Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " RFR ,Receive FIFO Reset" "No reset,Reset"
|
|
bitfld.long 0x00 0. " RFE ,Receive FIFO Enable" "Disabled,Enabled"
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "RFSR,Receive FIFO Status Register"
|
|
bitfld.long 0x00 12.--13. " NRFI ,Next Receiver FIFO In" "#0,#1,#2,#3"
|
|
bitfld.long 0x00 8.--9. " NRFO ,Next Receiver FIFO Out" "#0,#1,#2,#3"
|
|
hexmask.long.byte 0x00 0.--7. 1. " RFCNT ,Receive FIFO Counter"
|
|
wgroup.long 0x80++0x017
|
|
line.long 0x0 "TX0,ESAI Transmit Data Register 0"
|
|
hexmask.long.tbyte 0x0 0.--23. 1. " TX0 ,Stores the data to be transmitted"
|
|
line.long 0x4 "TX1,ESAI Transmit Data Register 1"
|
|
hexmask.long.tbyte 0x4 0.--23. 1. " TX1 ,Stores the data to be transmitted"
|
|
line.long 0x8 "TX2,ESAI Transmit Data Register 2"
|
|
hexmask.long.tbyte 0x8 0.--23. 1. " TX2 ,Stores the data to be transmitted"
|
|
line.long 0xC "TX3,ESAI Transmit Data Register 3"
|
|
hexmask.long.tbyte 0xC 0.--23. 1. " TX3 ,Stores the data to be transmitted"
|
|
line.long 0x10 "TX4,ESAI Transmit Data Register 4"
|
|
hexmask.long.tbyte 0x10 0.--23. 1. " TX4 ,Stores the data to be transmitted"
|
|
line.long 0x14 "TX5,ESAI Transmit Data Register 5"
|
|
hexmask.long.tbyte 0x14 0.--23. 1. " TX5 ,Stores the data to be transmitted"
|
|
wgroup.long 0x98++0x03
|
|
line.long 0x00 "TSR,ESAI Transmit Slot Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " TSR ,Transmit Slot Register"
|
|
rgroup.long 0xa0++0x0f
|
|
line.long 0x0 "RX0,ESAI Receive Data Registers 0"
|
|
hexmask.long.tbyte 0x0 0.--23. 1. " RX0 ,Data from the receive shift register"
|
|
line.long 0x4 "RX1,ESAI Receive Data Registers 1"
|
|
hexmask.long.tbyte 0x4 0.--23. 1. " RX1 ,Data from the receive shift register"
|
|
line.long 0x8 "RX2,ESAI Receive Data Registers 2"
|
|
hexmask.long.tbyte 0x8 0.--23. 1. " RX2 ,Data from the receive shift register"
|
|
line.long 0xC "RX3,ESAI Receive Data Registers 3"
|
|
hexmask.long.tbyte 0xC 0.--23. 1. " RX3 ,Data from the receive shift register"
|
|
rgroup.long 0xcc++0x03
|
|
line.long 0x00 "SAISR,ESAI Status Register"
|
|
bitfld.long 0x00 17. " TODFE ,SAISR Transmit Odd-Data Register Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 16. " TEDE ,SAISR Transmit Even-Data Register Empty" "Not empty,Empty"
|
|
bitfld.long 0x00 15. " TDE ,SAISR Transmit Data Register Empty" "Not empty,Empty"
|
|
textline " "
|
|
bitfld.long 0x00 14. " TUE ,SAISR Transmit Underrun Error Flag" "No error,Error"
|
|
bitfld.long 0x00 13. " TFS ,SAISR Transmit Frame Sync Flar" "Not occurred,Occurred"
|
|
bitfld.long 0x00 10. " RODF ,SAISR Receive Odd-Data Register Full" "Not full,Full"
|
|
textline " "
|
|
bitfld.long 0x00 9. " REDF ,SAISR Receive Even-Data Register Full" "Not full,Full"
|
|
bitfld.long 0x00 8. " RDF ,SAISR Receive Data Register Full" "Not full,Full"
|
|
bitfld.long 0x00 7. " ROE ,SAISR Receive Overrun Error Flag" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RFS ,SAISR Receive Frame Sync Flag" "Not occurred,Occurred"
|
|
bitfld.long 0x00 2. " IF2 ,SAISR Serial Input Flag 2" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x00 1. " IF1 ,SAISR Serial Inout Flag 1" "Not occurred,Occurred"
|
|
bitfld.long 0x00 0. " IF0 ,SAISR Serial Input Flag 0" "Not occurred,Occurred"
|
|
group.long 0xd0++0x14
|
|
line.long 0x00 "SAICR,ESAI Common Control Register"
|
|
bitfld.long 0x00 8. " ALC ,SAICR Alignment Control" "23 bit,15 bit"
|
|
bitfld.long 0x00 7. " TEBE ,SAICR Transmit External Buffer Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " SYNC ,SAICR Synchronous Mode Selection" "Asynchronous,Synchronous"
|
|
textline " "
|
|
bitfld.long 0x00 2. " OF2 ,SAICR Serial Output Flag 2" "Not occurred,Occurred"
|
|
bitfld.long 0x00 1. " OF1 ,SAICR Serial Output Flag 1" "Not occurred,Occurred"
|
|
bitfld.long 0x00 1. " OF0 ,SAICR Serial Output Flag 0" "Not occurred,Occurred"
|
|
line.long 0x04 "TCR,ESAI Transmit Contral Register"
|
|
bitfld.long 0x04 23. " TLIE ,TCR Transmit Last Slot Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 22. " TIE ,TCR Transmit Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 21. " TEDIE ,TCR Transmit Even Slot Data Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 20. " TEIE ,TCR Transmit Exception Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 19. " TPR ,TCR Transmit Section Personal Reset" "No reset,Reset"
|
|
bitfld.long 0x04 17. " PADC ,TCR Transmit Zero Padding Control" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 16. " TFSR ,TCR Transmit Frame Sync Relative Timing" "Start with the first bit of the data word of the first slot,Start with the last bit of the previous data word"
|
|
textline " "
|
|
bitfld.long 0x04 15. " TFSL ,TCR Transmit Frame Sync Length" "Word,1-bit"
|
|
bitfld.long 0x04 14. " TSWS[4] ,Slot and Word Length Select" "Disabled,Enabled"
|
|
bitfld.long 0x04 13. " TSWS[3] ,Slot and Word Length Select" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 12. " TSWS[2] ,Slot and Word Length Select" "Disabled,Enabled"
|
|
bitfld.long 0x04 11. " TSWS[1] ,Slot and Word Length Select" "Disabled,Enabled"
|
|
bitfld.long 0x04 10. " TSWS[0] ,Slot and Word Length Select" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 9. " TMOD[1] ,TCR Transmit Network Mode Control" "0,1"
|
|
bitfld.long 0x04 8. " TMOD[0] ,TCR Transmit Network Mode Control" "0,1"
|
|
bitfld.long 0x04 7. " TWA ,TCR Transmit Word Alignment Control" "Left-aligned,Right-aligned"
|
|
textline " "
|
|
bitfld.long 0x04 6. " TSHFD ,TCR Transmit Shift Direction" "MSB first,LSB first"
|
|
bitfld.long 0x04 5. " TE5 ,TCR ESAI Transmit 5 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 4. " TE4 ,TCR ESAI Transmit 4 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 3. " TE3 ,TCR ESAI Transmit 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 2. " TE2 ,TCR ESAI Transmit 2 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 1. " TE1 ,TCR ESAI Transmit 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x04 0. " TE0 ,TCR ESAI Transmit 0 Enable" "Disabled,Enabled"
|
|
line.long 0x08 "TCCR,ESAI Transmitter Clock Control Register"
|
|
bitfld.long 0x08 23. " THCKD ,TCCR Transmit High Frequency Clock Direction" "Input,Output"
|
|
bitfld.long 0x08 22. " TFSD ,TCCR Transmit Frame Sync Signal Direction" "Input,Output"
|
|
bitfld.long 0x08 21. " TCKD ,TCCR Transmit Clock Source Direction" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x08 20. " THCKP ,TCCR Transmit High Frequency Clock Polarity" "Positive,Negative"
|
|
bitfld.long 0x08 19. " TFSP ,TCCR Transmit Frame Sync Polarity" "Positive,Negative"
|
|
bitfld.long 0x08 18. " TCKP ,TCCR Transmit Clock Polarity" "Positive,Negative"
|
|
textline " "
|
|
bitfld.long 0x08 14.--17. " TFP ,TCCR T[3:0] High Frequency Clock Divider" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16"
|
|
bitfld.long 0x08 9.--13. " TDC ,TCCR T[4:0] Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
textline " "
|
|
bitfld.long 0x08 8. " TPSR ,TCCR Transmit Prescaler Range" "0,1"
|
|
hexmask.long.byte 0x08 0.--7. 1. " TPM ,TCCR Transmit Prescale Modulus Select"
|
|
line.long 0x0c "RCR,ESAI Receive Control Register"
|
|
bitfld.long 0x0c 23. " RLIE ,RCR Receive Last Slot Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 22. " RIE ,RCR Receive Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 21. " REDIE ,RCR Receive Even Slot Data Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 20. " REIE ,RCR Receive Exception Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 19. " RPR ,RCR Receiver Section Personal Reset" "No reset,Reset"
|
|
textline " "
|
|
bitfld.long 0x0c 16. " RFSR ,RCR Receiver Frame Sync Relative Timing" "Start with the first bit of the data word of the first slot,Start with the last bit of the previous data word"
|
|
textline " "
|
|
bitfld.long 0x0c 15. " RFSL ,RCR Receiver Frame Sync Length" "Word,1-bit"
|
|
bitfld.long 0x0c 14. " RSWS[4] ,RCR Receiver Slot and Word Select" "0,1"
|
|
bitfld.long 0x0c 13. " RSWS[3] ,RCR Receiver Slot and Word Select" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0c 12. " RSWS[2] ,RCR Receiver Slot and Word Select" "0,1"
|
|
bitfld.long 0x0c 11. " RSWS[1] ,RCR Receiver Slot and Word Select" "0,1"
|
|
bitfld.long 0x0c 10. " RSWS[0] ,RCR Receiver Slot and Word Select" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0c 9. " RMOD[1] ,RCR Receiver Network Mode Control" "0,1"
|
|
bitfld.long 0x0c 8. " RMOD[0] ,RCR Receiver Network Mode Control" "0,1"
|
|
bitfld.long 0x0c 7. " RWA ,RCR Receiver Word Alignment Control" "Left-aligned,Right-aligned"
|
|
textline " "
|
|
bitfld.long 0x0c 6. " RSHFD ,RCR Receiver Shift Direction" "MSB first,LSB first"
|
|
bitfld.long 0x0c 3. " RE3 ,RCR ESAI Receiver 3 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 2. " RE2 ,RCR ESAI Receiver 2 Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 1. " RE1 ,RCR ESAI Receiver 1 Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0c 0. " RE0 ,RCR ESAI Receiver 0 Enable" "Disabled,Enabled"
|
|
line.long 0x10 "RCCR,ESAI Receiver Clock Control Register"
|
|
bitfld.long 0x10 23. " RHCKD ,RCCR Receiver High Frequency Clock Direction" "Input,Output"
|
|
bitfld.long 0x10 22. " RFSD ,RCCR Receiver Frame Sync Signal Direction" "Input,Output"
|
|
bitfld.long 0x10 21. " RCKD ,RCCR Receiver Clock Source Direction" "Input,Output"
|
|
textline " "
|
|
bitfld.long 0x10 20. " RHCKP ,RCCR Receiver High Frequency Clock Polarity" "Rising edge,Falling edge"
|
|
bitfld.long 0x10 19. " RFSP ,RCCR Receiver Frame Sync Polarity" "Rising edge,Falling edge"
|
|
bitfld.long 0x10 18. " RCKP ,The Receiver Clock Polarity" "Rising edge,Falling edge"
|
|
textline " "
|
|
bitfld.long 0x10 14.--17. " RFP ,RCCR R[3:0] High Frequency Clock Divider" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16"
|
|
bitfld.long 0x10 9.--13. " RDC ,RCCR R[4:0] Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
textline " "
|
|
bitfld.long 0x10 8. " RPSP ,RCCR Receiver Prescaler Range" "0,1"
|
|
hexmask.long.byte 0x10 0.--7. 1. " RPM ,RCCR Receiver Prescale Modulus Select"
|
|
group.long 0xe4++0xf
|
|
line.long 0x00 "TSMA,ESAI Transmit Slot Mask Register A"
|
|
hexmask.long.word 0x00 0.--15. 1. " TS[15:0] ,Transmit Slot A"
|
|
line.long 0x04 "TSMB,ESAI Transmit Slot Mask Register B"
|
|
hexmask.long.word 0x04 0.--15. 1. " TS[31:16] ,Transmit Slot B"
|
|
line.long 0x08 "RSMA,ESAI Receive Slot Mask Register A"
|
|
hexmask.long.word 0x08 0.--15. 1. " RS[15:0] ,Receive Slot A"
|
|
line.long 0x0c "RSMB,ESAI Receive Slot Mask Register B"
|
|
hexmask.long.word 0x0c 0.--15. 1. " RS[31:16] ,Receive Slot B"
|
|
group.long 0xF8++0x07
|
|
line.long 0x00 "PRRC,Port C Direction Register"
|
|
bitfld.long 0x00 11. " PDC11 ,Port C Direction pin 11" "0,1"
|
|
bitfld.long 0x00 10. " PDC10 ,Port C Direction pin 10" "0,1"
|
|
bitfld.long 0x00 9. " PDC9 ,Port C Direction pin 9" "0,1"
|
|
bitfld.long 0x00 8. " PDC8 ,Port C Direction pin 8" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 7. " PDC7 ,Port C Direction pin 7" "0,1"
|
|
bitfld.long 0x00 6. " PDC6 ,Port C Direction pin 6" "0,1"
|
|
bitfld.long 0x00 5. " PDC5 ,Port C Direction pin 5" "0,1"
|
|
bitfld.long 0x00 4. " PDC4 ,Port C Direction pin 4" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 3. " PDC3 ,Port C Direction pin 3" "0,1"
|
|
bitfld.long 0x00 2. " PDC2 ,Port C Direction pin 2" "0,1"
|
|
bitfld.long 0x00 1. " PDC1 ,Port C Direction pin 1" "0,1"
|
|
bitfld.long 0x00 0. " PDC0 ,Port C Direction pin 0" "0,1"
|
|
line.long 0x04 "PCRC,Port C Control Register"
|
|
bitfld.long 0x04 11. " PC11 ,Port C Control pin 11" "0,1"
|
|
bitfld.long 0x04 10. " PC10 ,Port C Control pin 10" "0,1"
|
|
bitfld.long 0x04 9. " PC9 ,Port C Control pin 9" "0,1"
|
|
bitfld.long 0x04 8. " PC8 ,Port C Control pin 8" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 7. " PC7 ,Port C Control pin 7" "0,1"
|
|
bitfld.long 0x04 6. " PC6 ,Port C Control pin 6" "0,1"
|
|
bitfld.long 0x04 5. " PC5 ,Port C Control pin 5" "0,1"
|
|
bitfld.long 0x04 4. " PC4 ,Port C Control pin 4" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 3. " PC3 ,Port C Control pin 3" "0,1"
|
|
bitfld.long 0x04 2. " PC2 ,Port C Control pin 2" "0,1"
|
|
bitfld.long 0x04 1. " PC1 ,Port C Control pin 1" "0,1"
|
|
bitfld.long 0x04 0. " PC0 ,Port C Control pin 0" "0,1"
|
|
width 0xb
|
|
tree.end
|
|
tree "IPU (Image Processing Unit)"
|
|
base ad:0x53fc0000
|
|
width 0xA
|
|
tree "IPU Common Registers"
|
|
group.long 0x00++0x3
|
|
line.long 0x00 "IPU_CONF,IPU Configuration Register"
|
|
bitfld.long 0x00 8. " PXL_ENDIAN ,Pixel endianness" "Little,Big"
|
|
bitfld.long 0x00 7. " DU_EN ,Debug Unit enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " DI_EN ,Display Interface enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " ADC_EN ,Asynchronous Display Controller enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 4. " SDC_EN ,Synchronous Display Controller enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 3. " PF_EN ,Postfilter enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " ROT_EN ,Rotation Unit enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " IC_EN ,Image Converter enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " CSI_EN ,Camera Sensor interface enable" "Disabled,Enabled"
|
|
width 0x15
|
|
width 20.
|
|
tree "IPU Channel Buffer Registers"
|
|
textline " "
|
|
group.long 0x4++0xF
|
|
line.long 0x0 "IPU_CHA_BUF0_RDY,IPU Channels Buffer 0 Ready Register"
|
|
bitfld.long 0x0 31. " DMAPF_7_BUF0_RDY ,DMAPF 7 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 30. " DMAPF_6_BUF0_RDY ,DMAPF 6 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 29. " DMAPF_5_BUF0_RDY ,DMAPF 5 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 28. " DMAPF_4_BUF0_RDY ,DMAPF 4 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 27. " DMAPF_3_BUF0_RDY ,DMAPF 3 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 26. " DMAPF_2_BUF0_RDY ,DMAPF 2 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 25. " DMAPF_1_BUF0_RDY ,DMAPF 1 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 24. " DMAPF_0_BUF0_RDY ,DMAPF 0 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 23. " DMAADC_7_BUF0_RDY ,DMAADC 7 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 22. " DMAADC_6_BUF0_RDY ,DMAADC 6 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 21. " DMAADC_5_BUF0_RDY ,DMAADC 5 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 20. " DMAADC_4_BUF0_RDY ,DMAADC 4 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 19. " DMAADC_3_BUF0_RDY ,DMAADC 3 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 18. " DMAADC_2_BUF0_RDY ,DMAADC 2 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 17. " DMASDC_3_BUF0_RDY ,DMASDC 3 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 16. " DMASDC_2_BUF0_RDY ,DMASDC 2 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 15. " DMASDC_1_BUF0_RDY ,DMASDC 1 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 14. " DMASDC_0_BUF0_RDY ,DMASDC 0 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 13. " DMAIC_13_BUF0_RDY ,DMAIC 13 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 12. " DMAIC_12_BUF0_RDY ,DMAIC 12 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 11. " DMAIC_11_BUF0_RDY ,DMAIC 11 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 10. " DMAIC_10_BUF0_RDY ,DMAIC 10 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 9. " DMAIC_9_BUF0_RDY ,DMAIC 9 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 8. " DMAIC_8_BUF0_RDY ,DMAIC 8 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 7. " DMAIC_7_BUF0_RDY ,DMAIC 7 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 6. " DMAIC_6_BUF0_RDY ,DMAIC 6 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 5. " DMAIC_5_BUF0_RDY ,DMAIC 5 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 4. " DMAIC_4_BUF0_RDY ,DMAIC 4 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 3. " DMAIC_3_BUF0_RDY ,DMAIC 3 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 2. " DMAIC_2_BUF0_RDY ,DMAIC 2 Buffer 0 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x0 1. " DMAIC_1_BUF0_RDY ,DMAIC 1 Buffer 0 Ready" "Not ready,Ready"
|
|
bitfld.long 0x0 0. " DMAIC_0_BUF0_RDY ,DMAIC 0 Buffer 0 Ready" "Not ready,Ready"
|
|
line.long 0x4 "IPU_CHA_BUF1_RDY,IPU Channels Buffer 1 Ready Register"
|
|
bitfld.long 0x4 31. " DMAPF_7_BUF1_RDY ,DMAPF 7 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 30. " DMAPF_6_BUF1_RDY ,DMAPF 6 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 29. " DMAPF_5_BUF1_RDY ,DMAPF 5 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 28. " DMAPF_4_BUF1_RDY ,DMAPF 4 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 27. " DMAPF_3_BUF1_RDY ,DMAPF 3 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 26. " DMAPF_2_BUF1_RDY ,DMAPF 2 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 25. " DMAPF_1_BUF1_RDY ,DMAPF 1 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 24. " DMAPF_0_BUF1_RDY ,DMAPF 0 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 23. " DMAADC_7_BUF1_RDY ,DMAADC 7 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 22. " DMAADC_6_BUF1_RDY ,DMAADC 6 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 21. " DMAADC_5_BUF1_RDY ,DMAADC 5 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 20. " DMAADC_4_BUF1_RDY ,DMAADC 4 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 19. " DMAADC_3_BUF1_RDY ,DMAADC 3 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 18. " DMAADC_2_BUF1_RDY ,DMAADC 2 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 17. " DMASDC_3_BUF1_RDY ,DMASDC 3 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 16. " DMASDC_2_BUF1_RDY ,DMASDC 2 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 15. " DMASDC_1_BUF1_RDY ,DMASDC 1 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 14. " DMASDC_0_BUF1_RDY ,DMASDC 0 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 13. " DMAIC_13_BUF1_RDY ,DMAIC 13 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 12. " DMAIC_12_BUF1_RDY ,DMAIC 12 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 11. " DMAIC_11_BUF1_RDY ,DMAIC 11 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 10. " DMAIC_10_BUF1_RDY ,DMAIC 10 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 9. " DMAIC_9_BUF1_RDY ,DMAIC 9 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 8. " DMAIC_8_BUF1_RDY ,DMAIC 8 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 7. " DMAIC_7_BUF1_RDY ,DMAIC 7 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 6. " DMAIC_6_BUF1_RDY ,DMAIC 6 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 5. " DMAIC_5_BUF1_RDY ,DMAIC 5 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 4. " DMAIC_4_BUF1_RDY ,DMAIC 4 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 3. " DMAIC_3_BUF1_RDY ,DMAIC 3 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 2. " DMAIC_2_BUF1_RDY ,DMAIC 2 Buffer 1 Ready" "Not ready,Ready"
|
|
textline " "
|
|
bitfld.long 0x4 1. " DMAIC_1_BUF1_RDY ,DMAIC 1 Buffer 1 Ready" "Not ready,Ready"
|
|
bitfld.long 0x4 0. " DMAIC_0_BUF1_RDY ,DMAIC 0 Buffer 1 Ready" "Not ready,Ready"
|
|
line.long 0x8 "IPU_CHA_DB_MODE_SEL,IPU Channel Double Buffer Mode Select Register"
|
|
bitfld.long 0x8 29. " DMAPF_5_DB_MODE_SEL ,DMAPF 5 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 26. " DMAPF_2_DB_MODE_SEL ,DMAPF 2 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 19. " DMAADC_3_DB_MODE_SEL ,DMAADC 3 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 18. " DMAADC_2_DB_MODE_SEL ,DMAADC 2 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 16. " DMASDC_2_DB_MODE_SEL ,DMASDC 2 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 15. " DMASDC_1_DB_MODE_SEL ,DMASDC 1 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 14. " DMASDC_0_DB_MODE_SEL ,DMASDC 0 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 13. " DMAIC_13_DB_MODE_SEL ,DMAIC 13 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 12. " DMAIC_12_DB_MODE_SEL ,DMAIC 12 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 11. " DMAIC_11_DB_MODE_SEL ,DMAIC 11 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 10. " DMAIC_10_DB_MODE_SEL ,DMAIC 10 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 9. " DMAIC_9_DB_MODE_SEL ,DMAIC 9 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 8. " DMAIC_8_DB_MODE_SEL ,DMAIC 8 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 7. " DMAIC_7_DB_MODE_SEL ,DMAIC 7 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 6. " DMAIC_6_DB_MODE_SEL ,DMAIC 6 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 5. " DMAIC_5_DB_MODE_SEL ,DMAIC 5 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 4. " DMAIC_4_DB_MODE_SEL ,DMAIC 4 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 3. " DMAIC_3_DB_MODE_SEL ,DMAIC 3 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 2. " DMAIC_2_DB_MODE_SEL ,DMAIC 2 Double buffer mode select" "Not selected,Selected"
|
|
bitfld.long 0x8 1. " DMAIC_1_DB_MODE_SEL ,DMAIC 1 Double buffer mode select" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x8 0. " DMAIC_0_DB_MODE_SEL ,DMAIC 0 Double buffer mode select" "Not selected,Selected"
|
|
line.long 0xC "IPU_CHA_CUR_BUF,IPU Channel Current Buffer Register"
|
|
eventfld.long 0xC 31. " DMAPF_7_CUR_BUF ,DMAPF 7 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 30. " DMAPF_6_CUR_BUF ,DMAPF 6 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 29. " DMAPF_5_CUR_BUF ,DMAPF 5 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 28. " DMAPF_4_CUR_BUF ,DMAPF 4 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 27. " DMAPF_3_CUR_BUF ,DMAPF 3 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 26. " DMAPF_2_CUR_BUF ,DMAPF 2 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 25. " DMAPF_1_CUR_BUF ,DMAPF 1 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 24. " DMAPF_0_CUR_BUF ,DMAPF 0 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 23. " DMAADC_7_CUR_BUF ,DMAADC 7 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 22. " DMAADC_6_CUR_BUF ,DMAADC 6 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 21. " DMAADC_5_CUR_BUF ,DMAADC 5 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 20. " DMAADC_4_CUR_BUF ,DMAADC 4 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 19. " DMAADC_3_CUR_BUF ,DMAADC 3 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 18. " DMAADC_2_CUR_BUF ,DMAADC 2 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 17. " DMASDC_3_CUR_BUF ,DMASDC 3 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 16. " DMASDC_2_CUR_BUF ,DMASDC 2 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 15. " DMASDC_1_CUR_BUF ,DMASDC 1 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 14. " DMASDC_0_CUR_BUF ,DMASDC 0 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 13. " DMAIC_13_CUR_BUF ,DMAIC 13 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 12. " DMAIC_12_CUR_BUF ,DMAIC 12 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 11. " DMAIC_11_CUR_BUF ,DMAIC 11 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 10. " DMAIC_10_CUR_BUF ,DMAIC 10 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 9. " DMAIC_9_CUR_BUF ,DMAIC 9 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 8. " DMAIC_8_CUR_BUF ,DMAIC 8 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 7. " DMAIC_7_CUR_BUF ,DMAIC 7 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 6. " DMAIC_6_CUR_BUF ,DMAIC 6 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 5. " DMAIC_5_CUR_BUF ,DMAIC 5 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 4. " DMAIC_4_CUR_BUF ,DMAIC 4 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 3. " DMAIC_3_CUR_BUF ,DMAIC 3 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 2. " DMAIC_2_CUR_BUF ,DMAIC 2 Current Buffer" "Buffer 0,Buffer 1"
|
|
textline " "
|
|
eventfld.long 0xC 1. " DMAIC_1_CUR_BUF ,DMAIC 1 Current Buffer" "Buffer 0,Buffer 1"
|
|
eventfld.long 0xC 0. " DMAIC_0_CUR_BUF ,DMAIC 0 Current Buffer" "Buffer 0,Buffer 1"
|
|
tree.end
|
|
width 0x12
|
|
textline " "
|
|
group.long 0x14++0x7
|
|
line.long 0x0 "IPU_FS_PROC_FLOW,IPU Frame Synchronization Processing Flow Register"
|
|
bitfld.long 0x0 28.--30. " PP_ROT_DEST_SEL ,Rotation for post-processing destination select" "MCU,Post-processing,ADC1,ADC2,SDC background,SDC foreground,?..."
|
|
bitfld.long 0x0 24.--26. " PP_DEST_SEL ,Post-processing destination select" "MCU,Post-processing,ADC1,ADC2,SDC background,SDC foreground,ADC PP,?..."
|
|
textline " "
|
|
bitfld.long 0x0 20.--22. " PRPVF_ROT_DEST_SEL ,Rotation for view-finder destination select" "MCU,Reserved,ADC1,ADC2,SDC background,SDC foreground,?..."
|
|
bitfld.long 0x0 16.--18. " PRPVF_DEST_SEL ,Pre-processing for view-finder destination select" "MCU,View-finder,ADC1,ADC2,SDC background,SDC foreground,ADC VF,?..."
|
|
textline " "
|
|
bitfld.long 0x0 12.--13. " PF_DEST_SEL ,Post-filtering destination select" "MCU,Post-processing,Rotation,?..."
|
|
bitfld.long 0x0 10.--11. " PP_ROT_SRC_SEL ,Rotation for post processing source select" "MCU,Post-processing,Post-filtering,?..."
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " PP_SRC_SEL ,Post-processing source select" "MCU,Post-filtering,Rotation,?..."
|
|
bitfld.long 0x0 6. " PRPVF_ROT_SRC_SEL ,Rotation for view-finder source select" "MCU,View-finder"
|
|
textline " "
|
|
bitfld.long 0x0 5. " PRPENC_ROT_SRC_SEL ,Rotation for encoding source select" "MCU,Encoding"
|
|
bitfld.long 0x0 4. " PRPENC_DEST_SEL ,Pre-processing for encoding destination select" "MCU,Encoding"
|
|
textline " "
|
|
bitfld.long 0x0 1. " VF_IN_VALID ,View-finder input valid" "Not valid,Valid"
|
|
bitfld.long 0x0 0. " ENC_IN_VALID ,Encoding input valid" "Not valid,Valid"
|
|
line.long 0x4 "IPU_FS_DISP_FLOW,IPU Frame Synchronization Displaying Flow Register"
|
|
hexmask.long.word 0x4 16.--25. 1. " AUTO_REF_PER ,Autorefresh period minus 1"
|
|
textline " "
|
|
bitfld.long 0x4 12.--14. " ADC3_SRC_SEL ,ADC system channel 2 source select" "MCU,Rotation for View-Finder,Rotation for Post-processing,View-Finder,Post-processing,Snooping,Autorefresh,Autorefresh with snooping"
|
|
textline " "
|
|
bitfld.long 0x4 8.--10. " ADC2_SRC_SEL ,ADC system channel 1 source select" "MCU,Rotation for View-Finder,Rotation for Post-processing,View-Finder,Post-processing,Snooping,Autorefresh,Autorefresh with snooping"
|
|
textline " "
|
|
bitfld.long 0x4 4.--6. " SDC1_SRC_SEL ,SDC foreground channel (1) source select" "MCU,Rotation for View-Finder,Rotation for Post-processing,View-Finder,Post-processing,?..."
|
|
textline " "
|
|
bitfld.long 0x4 0.--2. " SDC0_SRC_SEL ,SDC background channel (0) source select" "MCU,Rotation for View-Finder,Rotation for Post-processing,View-Finder,Post-processing,?..."
|
|
rgroup.long 0x1c++0x3
|
|
line.long 0x00 "IPU_TASKS_STAT,IPU Tasks Status Register"
|
|
bitfld.long 0x00 31. " ADC_SYS2CHAN_LOCK ,ADC SYS2 Channel Locked" "Unlocked,Locked"
|
|
bitfld.long 0x00 30. " ADC_SYS1CHAN_LOCK ,ADC SYS1 Channel Locked" "Unlocked,Locked"
|
|
textline " "
|
|
bitfld.long 0x00 29. " ADC_PPCHAN_LOCK ,ADC Post-Processing Channel Locked" "Unlocked,Locked"
|
|
bitfld.long 0x00 28. " ADC_PRPCHAN_LOCK ,ADC Pre-Processing Channel Locked" "Unlocked,Locked"
|
|
textline " "
|
|
bitfld.long 0x00 26.--27. " ADCSYS2_TSTAT ,ADC system channel 2 task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
bitfld.long 0x00 24.--25. " ADCSYS1_TSTAT ,ADC system channel 1 task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
textline " "
|
|
bitfld.long 0x00 22.--23. " PF_TSTAT ,Post-filtering task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
bitfld.long 0x00 20.--21. " PP_ROT_TSTAT ,Rotation for post-processing task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
textline " "
|
|
bitfld.long 0x00 18.--19. " VF_ROT_TSTAT ,Rotation for View-Finder task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
bitfld.long 0x00 16.--17. " ENC_ROT_TSTAT ,Rotation for encoding task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
textline " "
|
|
bitfld.long 0x00 14. " PF_H264_Y_PAUSE ,Pause in the PF operation in H.264 mode" "Not paused,Paused"
|
|
bitfld.long 0x00 13. " SDC_PIX_SKIP ,Skipping pixels on synchronous display after overrun error in SDC" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x00 11.--12. " PP_TSTAT ,Post-processing task status" "IDLE,ACTIVE,W4RDY,?..."
|
|
bitfld.long 0x00 9.--10. " VF_TSTAT ,Pre-processing for view-finder task status" "IDLE,ACTIVE,PAUSE,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7.--8. " ENC_TSTAT ,Encoding directly from CSI task status" "IDLE,ACTIVE,PAUSE,?..."
|
|
bitfld.long 0x00 4.--6. " MEM2PRP_TSTAT ,Memory to PRP task status" "IDLE,BOTH_ACTIVE,ENC_ACTIVE,VF_ACTIVE,BOTH_PAUSE,?..."
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " CSI2MEM_TSTAT ,CSI directly to memory task status" "IDLE,ACTIVE,PAUSE,?..."
|
|
bitfld.long 0x00 0.--1. " CSI_SKIP_TSTAT ,Next VF and ENC frames skipping status in the CSI" "ENC/VF,ENC,VF,Not skipped"
|
|
group.long 0x20++0x7
|
|
line.long 0x00 "IPU_IMA_ADDR,IPU Internal Memory Access Address Register"
|
|
bitfld.long 0x00 16.--19. " MEM_NU ,Memory number" "Task Parameter,Channel Parameter,Look-Up Table,Template,Asynchronous Display Buffer,Downsizing Output,Down Sizing Temporary,Input Buffer,Main Processing,Rotation,Post Filter,Synchronous Display Buffer,?..."
|
|
hexmask.long.word 0x00 3.--15. 1. " ROW_NU ,Row number"
|
|
textline " "
|
|
bitfld.long 0x00 0.--2. " WORD_NU ,Word number" "Word 0,Word 1,Word 2,Word 3,Word 4,?..."
|
|
line.long 0x04 "IPU_IMA_DATA,IPU Internal Memory Access Data Register"
|
|
width 0x10
|
|
tree "IPU Interrupt Control Registers"
|
|
group.long 0x28++0x13
|
|
line.long 0x0 "IPU_INT_CTRL_1,IPU Interrupt Control Register 1"
|
|
bitfld.long 0x0 31. " DMAPF_7_EOF_EN ,DMAPF 7 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 30. " DMAPF_6_EOF_EN ,DMAPF 6 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 29. " DMAPF_5_EOF_EN ,DMAPF 5 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 28. " DMAPF_4_EOF_EN ,DMAPF 4 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 27. " DMAPF_3_EOF_EN ,DMAPF 3 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 26. " DMAPF_2_EOF_EN ,DMAPF 2 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 25. " DMAPF_1_EOF_EN ,DMAPF 1 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 24. " DMAPF_0_EOF_EN ,DMAPF 0 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 23. " DMAADC_7_EOF_EN ,DMAADC 7 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 22. " DMAADC_6_EOF_EN ,DMAADC 6 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 21. " DMAADC_5_EOF_EN ,DMAADC 5 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 20. " DMAADC_4_EOF_EN ,DMAADC 4 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 19. " DMAADC_3_EOF_EN ,DMAADC 3 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 18. " DMAADC_2_EOF_EN ,DMAADC 2 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 17. " DMASDC_3_EOF_EN ,DMASDC 3 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 16. " DMASDC_2_EOF_EN ,DMASDC 2 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 15. " DMASDC_1_EOF_EN ,DMASDC 1 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 14. " DMASDC_0_EOF_EN ,DMASDC 0 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 13. " DMAIC_13_EOF_EN ,DMAIC 13 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 12. " DMAIC_12_EOF_EN ,DMAIC 12 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 11. " DMAIC_11_EOF_EN ,DMAIC 11 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 10. " DMAIC_10_EOF_EN ,DMAIC 10 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 9. " DMAIC_9_EOF_EN ,DMAIC 9 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 8. " DMAIC_8_EOF_EN ,DMAIC 8 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 7. " DMAIC_7_EOF_EN ,DMAIC 7 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " DMAIC_6_EOF_EN ,DMAIC 6 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 5. " DMAIC_5_EOF_EN ,DMAIC 5 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " DMAIC_4_EOF_EN ,DMAIC 4 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 3. " DMAIC_3_EOF_EN ,DMAIC 3 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 2. " DMAIC_2_EOF_EN ,DMAIC 2 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 1. " DMAIC_1_EOF_EN ,DMAIC 1 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " DMAIC_0_EOF_EN ,DMAIC 0 Enable End of Frame of Channel interrupt" "Disabled,Enabled"
|
|
line.long 0x4 "IPU_INT_CTRL_2,IPU Interrupt Control Register 2"
|
|
bitfld.long 0x4 31. " DMAPF_7_NFACK_EN ,DMAPF 7 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 30. " DMAPF_6_NFACK_EN ,DMAPF 6 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 29. " DMAPF_5_NFACK_EN ,DMAPF 5 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 28. " DMAPF_4_NFACK_EN ,DMAPF 4 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 27. " DMAPF_3_NFACK_EN ,DMAPF 3 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 26. " DMAPF_2_NFACK_EN ,DMAPF 2 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 25. " DMAPF_1_NFACK_EN ,DMAPF 1 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 24. " DMAPF_0_NFACK_EN ,DMAPF 0 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 23. " DMAADC_7_NFACK_EN ,DMAADC 7 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " DMAADC_6_NFACK_EN ,DMAADC 6 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 21. " DMAADC_5_NFACK_EN ,DMAADC 5 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 20. " DMAADC_4_NFACK_EN ,DMAADC 4 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 19. " DMAADC_3_NFACK_EN ,DMAADC 3 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 18. " DMAADC_2_NFACK_EN ,DMAADC 2 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 17. " DMASDC_3_NFACK_EN ,DMASDC 3 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 16. " DMASDC_2_NFACK_EN ,DMASDC 2 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 15. " DMASDC_1_NFACK_EN ,DMASDC 1 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 14. " DMASDC_0_NFACK_EN ,DMASDC 0 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 13. " DMAIC_13_NFACK_EN ,DMAIC 13 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 12. " DMAIC_12_NFACK_EN ,DMAIC 12 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 11. " DMAIC_11_NFACK_EN ,DMAIC 11 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " DMAIC_10_NFACK_EN ,DMAIC 10 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 9. " DMAIC_9_NFACK_EN ,DMAIC 9 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 8. " DMAIC_8_NFACK_EN ,DMAIC 8 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " DMAIC_7_NFACK_EN ,DMAIC 7 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " DMAIC_6_NFACK_EN ,DMAIC 6 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 5. " DMAIC_5_NFACK_EN ,DMAIC 5 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 4. " DMAIC_4_NFACK_EN ,DMAIC 4 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 3. " DMAIC_3_NFACK_EN ,DMAIC 3 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 2. " DMAIC_2_NFACK_EN ,DMAIC 2 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 1. " DMAIC_1_NFACK_EN ,DMAIC 1 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x4 0. " DMAIC_0_NFACK_EN ,DMAIC 0 Enable new frame and ACK of channel interrupt" "Disabled,Enabled"
|
|
line.long 0x8 "IPU_INT_CTRL_3,IPU Interrupt Control Register 3"
|
|
bitfld.long 0x8 23. " STOP_MODE_ACK_EN ,Control of stop mode interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 22. " ADC_SYS2_EOF_EN ,Control of end-of-frame interrupt for the ADC system 2 channel" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 21. " ADC_SYS1_EOF_EN ,Control of end-of-frame interrupt for the ADC system 1 channel" "Disabled,Enabled"
|
|
bitfld.long 0x8 20. " ADC_PP_EOF_EN ,Control of end-of-frame interrupt for the ADC postprocessing channel" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 19. " ADC_PRP_EOF_EN ,Control of end-of-frame interrupt for the ADC preprocessing channel" "Disabled,Enabled"
|
|
bitfld.long 0x8 18. " ADC_DISP12_VSYNC_EN ,Control of VSYNC interrupt for displays 1 and 2" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 17. " ADC_DISP0_VSYNC_EN ,Control of VSYNC interrupt for display 0" "Disabled,Enabled"
|
|
bitfld.long 0x8 16. " SDC_DISP3_VSYNC_EN ,Control of VSYNC interrupt for display 3" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 15. " DMAADC_3_SBUF_END_EN ,Control of DMAADC channel 3 scroll buffer end interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 14. " DMAADC_2_SBUF_END_EN ,Control of DMAADC channel 2 scroll buffer end interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 13. " DMASDC_2_SBUF_END_EN ,Control of DMASDC channel 2 scroll buffer end interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 12. " DMASDC_1_SBUF_END_EN ,Control of DMASDC channel 1 scroll buffer end interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 11. " DMASDC_0_SBUF_END_EN ,Control of DMASDC channel 0 scroll buffer end interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 10. " DMAIC_6_SBUF_END_EN ,Control of DMAIC channel 6 scroll buffer end interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 9. " DMAIC_5_SBUF_END_EN ,Control of DMAIC channel 5 scroll buffer end interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 8. " DMAIC_4_SBUF_END_EN ,Control of DMAIC channel 4 scroll buffer end interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 7. " DMAIC_3_SBUF_END_EN ,Control of DMAIC channel 3 scroll buffer end interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 6. " CSI_EOF_EN ,Enable CSI_EOF interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 5. " CSI_NF_EN ,Enable CSI_NF interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 4. " SERIAL_DATA_FINISH_EN ,Enable the DI serial data finish interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 3. " SDC_MSK_EOF_EN ,Enable SDC Mask EOF interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 2. " SDC_FG_EOF_EN ,Enable SDC Foreground EOF interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x8 1. " SDC_BG_EOF_EN ,Enable SDC Background EOF interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x8 0. " BRK_RQ_STAT_EN ,Enable BRK_RQ interrupt" "Disabled,Enabled"
|
|
line.long 0xC "IPU_INT_CTRL_4,IPU Interrupt Control Register 4"
|
|
bitfld.long 0xC 31. " DMAPF_7_NFB4EOF_ERR_EN ,DMAPF 7 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 30. " DMAPF_6_NFB4EOF_ERR_EN ,DMAPF 6 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 29. " DMAPF_5_NFB4EOF_ERR_EN ,DMAPF 5 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 28. " DMAPF_4_NFB4EOF_ERR_EN ,DMAPF 4 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 27. " DMAPF_3_NFB4EOF_ERR_EN ,DMAPF 3 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 26. " DMAPF_2_NFB4EOF_ERR_EN ,DMAPF 2 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 25. " DMAPF_1_NFB4EOF_ERR_EN ,DMAPF 1 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 24. " DMAPF_0_NFB4EOF_ERR_EN ,DMAPF 0 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 23. " DMAADC_7_NFB4EOF_ERR_EN ,DMAADC 7 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 22. " DMAADC_6_NFB4EOF_ERR_EN ,DMAADC 6 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 21. " DMAADC_5_NFB4EOF_ERR_EN ,DMAADC 5 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 20. " DMAADC_4_NFB4EOF_ERR_EN ,DMAADC 4 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 19. " DMAADC_3_NFB4EOF_ERR_EN ,DMAADC 3 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 18. " DMAADC_2_NFB4EOF_ERR_EN ,DMAADC 2 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 17. " DMASDC_3_NFB4EOF_ERR_EN ,DMASDC 3 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 16. " DMASDC_2_NFB4EOF_ERR_EN ,DMASDC 2 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 15. " DMASDC_1_NFB4EOF_ERR_EN ,DMASDC 1 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 14. " DMASDC_0_NFB4EOF_ERR_EN ,DMASDC 0 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 13. " DMAIC_13_NFB4EOF_ERR_EN ,DMAIC 13 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 12. " DMAIC_12_NFB4EOF_ERR_EN ,DMAIC 12 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 11. " DMAIC_11_NFB4EOF_ERR_EN ,DMAIC 11 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 10. " DMAIC_10_NFB4EOF_ERR_EN ,DMAIC 10 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 9. " DMAIC_9_NFB4EOF_ERR_EN ,DMAIC 9 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 8. " DMAIC_8_NFB4EOF_ERR_EN ,DMAIC 8 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 7. " DMAIC_7_NFB4EOF_ERR_EN ,DMAIC 7 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 6. " DMAIC_6_NFB4EOF_ERR_EN ,DMAIC 6 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 5. " DMAIC_5_NFB4EOF_ERR_EN ,DMAIC 5 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 4. " DMAIC_4_NFB4EOF_ERR_EN ,DMAIC 4 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 3. " DMAIC_3_NFB4EOF_ERR_EN ,DMAIC 3 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 2. " DMAIC_2_NFB4EOF_ERR_EN ,DMAIC 2 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0xC 1. " DMAIC_1_NFB4EOF_ERR_EN ,DMAIC 1 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
bitfld.long 0xC 0. " DMAIC_0_NFB4EOF_ERR_EN ,DMAIC 0 The control of NFB4EOF error enable" "Disabled,Enabled"
|
|
line.long 0x10 "IPU_INT_CTRL_5,IPU Interrupt Control Register 5"
|
|
bitfld.long 0x10 16. " SAHB_ADDR_ERR_EN ,Enable SAHB_ADDR_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 15. " DI_LLA_LOCK_ERR_EN ,Enable DI_LLA_LOCK_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 14. " DI_ADC_LOCK_ERR_EN ,Enable DI_ADC_LOCK_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 13. " VF_FRM_LOST_ERR_EN ,Enable VF_FRM_LOST_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 12. " ENC_FRM_LOST_ERR_EN ,Enable ENC_FRM_LOST_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 11. " BAYER_FRM_LOST_ERR_EN ,Enable BAYER_FRM_LOST_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 10. " SDC_MSK_ERR_EN ,Enable SDC_MSK_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 9. " SDC_FGD_ERR_EN ,Enable SDC_FGD_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 8. " SDC_BGD_ERR_EN ,Enable SDC_BGD_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 7. " AHB_M2_ERR_EN ,Enable AHB_M2_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 6. " AHB_M1_ERR_EN ,Enable AHB_M1_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 5. " ADC_SYS2_TEARING_ERR_EN ,Enable ADC_SYS2_TEARING_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 4. " ADC_SYS1_TEARING_ERR_EN ,Enable ADC_SYS1_TEARING_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 3. " ADC_PP_TEARING_ERR_EN ,Enable ADC_PP_TEARING_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 2. " VF_BUF_OVF_ERR_EN ,Enable VF_BUF_OVF_ERR interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x10 1. " ENC_BUF_OVF_ERR_EN ,Enable ENC_BUF_OVF_ERR interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x10 0. " BAYER_BUF_OVF_ERR_EN ,Enable BAYER_BUF_OVF_ERR interrupt" "Disabled,Enabled"
|
|
tree.end
|
|
tree "IPU Interrupt Status Registers"
|
|
group.long 0x3c++0x13
|
|
line.long 0x00 "IPU_INT_STAT_1,IPU Interrupt Status Register 1"
|
|
eventfld.long 0x0 31. " DMAPF_7_EOF ,DMAPF 7 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 30. " DMAPF_6_EOF ,DMAPF 6 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 29. " DMAPF_5_EOF ,DMAPF 5 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 28. " DMAPF_4_EOF ,DMAPF 4 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 27. " DMAPF_3_EOF ,DMAPF 3 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 26. " DMAPF_2_EOF ,DMAPF 2 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 25. " DMAPF_1_EOF ,DMAPF 1 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 24. " DMAPF_0_EOF ,DMAPF 0 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 23. " DMAADC_7_EOF ,DMAADC 7 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 22. " DMAADC_6_EOF ,DMAADC 6 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 21. " DMAADC_5_EOF ,DMAADC 5 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 20. " DMAADC_4_EOF ,DMAADC 4 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 19. " DMAADC_3_EOF ,DMAADC 3 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 18. " DMAADC_2_EOF ,DMAADC 2 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 17. " DMASDC_3_EOF ,DMASDC 3 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 16. " DMASDC_2_EOF ,DMASDC 2 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 15. " DMASDC_1_EOF ,DMASDC 1 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 14. " DMASDC_0_EOF ,DMASDC 0 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 13. " DMAIC_13_EOF ,DMAIC 13 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 12. " DMAIC_12_EOF ,DMAIC 12 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 11. " DMAIC_11_EOF ,DMAIC 11 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 10. " DMAIC_10_EOF ,DMAIC 10 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 9. " DMAIC_9_EOF ,DMAIC 9 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 8. " DMAIC_8_EOF ,DMAIC 8 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 7. " DMAIC_7_EOF ,DMAIC 7 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 6. " DMAIC_6_EOF ,DMAIC 6 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 5. " DMAIC_5_EOF ,DMAIC 5 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 4. " DMAIC_4_EOF ,DMAIC 4 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 3. " DMAIC_3_EOF ,DMAIC 3 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 2. " DMAIC_2_EOF ,DMAIC 2 End of frame" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x0 1. " DMAIC_1_EOF ,DMAIC 1 End of frame" "No interrupt,Interrupt"
|
|
eventfld.long 0x0 0. " DMAIC_0_EOF ,DMAIC 0 End of frame" "No interrupt,Interrupt"
|
|
line.long 0x04 "IPU_INT_STAT_2,IPU Interrupt Status Register 2"
|
|
eventfld.long 0x4 31. " DMAPF_7_NFACK ,DMAPF 7 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 30. " DMAPF_6_NFACK ,DMAPF 6 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 29. " DMAPF_5_NFACK ,DMAPF 5 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 28. " DMAPF_4_NFACK ,DMAPF 4 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 27. " DMAPF_3_NFACK ,DMAPF 3 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 26. " DMAPF_2_NFACK ,DMAPF 2 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 25. " DMAPF_1_NFACK ,DMAPF 1 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 24. " DMAPF_0_NFACK ,DMAPF 0 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 23. " DMAADC_7_NFACK ,DMAADC 7 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 22. " DMAADC_6_NFACK ,DMAADC 6 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 21. " DMAADC_5_NFACK ,DMAADC 5 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 20. " DMAADC_4_NFACK ,DMAADC 4 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 19. " DMAADC_3_NFACK ,DMAADC 3 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 18. " DMAADC_2_NFACK ,DMAADC 2 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 17. " DMASDC_3_NFACK ,DMASDC 3 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 16. " DMASDC_2_NFACK ,DMASDC 2 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 15. " DMASDC_1_NFACK ,DMASDC 1 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 14. " DMASDC_0_NFACK ,DMASDC 0 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 13. " DMAIC_13_NFACK ,DMAIC 13 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 12. " DMAIC_12_NFACK ,DMAIC 12 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 11. " DMAIC_11_NFACK ,DMAIC 11 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 10. " DMAIC_10_NFACK ,DMAIC 10 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 9. " DMAIC_9_NFACK ,DMAIC 9 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 8. " DMAIC_8_NFACK ,DMAIC 8 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 7. " DMAIC_7_NFACK ,DMAIC 7 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 6. " DMAIC_6_NFACK ,DMAIC 6 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 5. " DMAIC_5_NFACK ,DMAIC 5 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 4. " DMAIC_4_NFACK ,DMAIC 4 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 3. " DMAIC_3_NFACK ,DMAIC 3 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 2. " DMAIC_2_NFACK ,DMAIC 2 NFACK" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x4 1. " DMAIC_1_NFACK ,DMAIC 1 NFACK" "No interrupt,Interrupt"
|
|
eventfld.long 0x4 0. " DMAIC_0_NFACK ,DMAIC 0 NFACK" "No interrupt,Interrupt"
|
|
line.long 0x08 "IPU_INT_STAT_3,IPU Interrupt Status Register 3"
|
|
eventfld.long 0x08 23. " STOP_MODE_ACK ,Control of stop mode interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 22. " ADC_SYS2_EOF ,Status of end-of-frame interrupt for the ADC system 2 channel" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 21. " ADC_SYS1_EOF ,Status of end-of-frame interrupt for the ADC system 1 channel" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 20. " ADC_PP_EOF ,Status of end-of-frame interrupt for the ADC postprocessing channel" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 19. " ADC_PRP_EOF ,Status of end-of-frame interrupt for the ADC preprocessing channel" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 18. " ADC_DISP12_VSYNC ,Status of VSYNC interrupt for displays 1 and 2" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 17. " ADC_DISP0_VSYNC ,Status of VSYNC interrupt for display 0" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 16. " SDC_DISP3_VSYNC ,Status of VSYNC interrupt for display 3" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 15. " DMAADC_3_SBUF_END ,Status of DMASDC channel 3 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 14. " DMAADC_2_SBUF_END ,Status of DMAADC channel 2 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 13. " DMASDC_2_SBUF_END ,Status of DMASDC channel 2 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 12. " DMASDC_1_SBUF_END ,Status of DMASDC channel 1 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 11. " DMASDC_0_SBUF_END ,Status of DMASDC channel 0 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 10. " DMAIC_6_SBUF_END ,Status of DMAIC channel 6 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 9. " DMAIC_5_SBUF_END ,Status of DMAIC channel 5 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 8. " DMAIC_4_SBUF_END ,Status of DMAIC channel 4 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 7. " DMAIC_3_SBUF_END ,Status of DMAIC channel 3 scroll buffer end interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 6. " CSI_EOF ,Status of CSI_EOF interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 5. " CSI_NF ,Status of CSI_NF interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 4. " SERIAL_DATA_FINISH ,Status the DI serial data finish interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 3. " SDC_MSK_EOF ,Status of SDC mask EOF interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 2. " SDC_FG_EOF ,Status of SDC foreground EOF interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x08 1. " SDC_BG_EOF ,Status of SDC background EOF interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x08 0. " BRK_RQ_STAT ,Status of BRK_RQ interrupt" "No interrupt,Interrupt"
|
|
line.long 0x0c "IPU_INT_STAT_4,IPU Interrupt Status Register 4"
|
|
eventfld.long 0xC 31. " DMAPF_7_NFB4EOF_ERR ,DMAPF 7 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 30. " DMAPF_6_NFB4EOF_ERR ,DMAPF 6 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 29. " DMAPF_5_NFB4EOF_ERR ,DMAPF 5 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 28. " DMAPF_4_NFB4EOF_ERR ,DMAPF 4 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 27. " DMAPF_3_NFB4EOF_ERR ,DMAPF 3 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 26. " DMAPF_2_NFB4EOF_ERR ,DMAPF 2 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 25. " DMAPF_1_NFB4EOF_ERR ,DMAPF 1 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 24. " DMAPF_0_NFB4EOF_ERR ,DMAPF 0 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 23. " DMAADC_7_NFB4EOF_ERR ,DMAADC 7 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 22. " DMAADC_6_NFB4EOF_ERR ,DMAADC 6 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 21. " DMAADC_5_NFB4EOF_ERR ,DMAADC 5 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 20. " DMAADC_4_NFB4EOF_ERR ,DMAADC 4 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 19. " DMAADC_3_NFB4EOF_ERR ,DMAADC 3 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 18. " DMAADC_2_NFB4EOF_ERR ,DMAADC 2 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 17. " DMASDC_3_NFB4EOF_ERR ,DMASDC 3 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 16. " DMASDC_2_NFB4EOF_ERR ,DMASDC 2 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 15. " DMASDC_1_NFB4EOF_ERR ,DMASDC 1 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 14. " DMASDC_0_NFB4EOF_ERR ,DMASDC 0 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 13. " DMAIC_13_NFB4EOF_ERR ,DMAIC 13 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 12. " DMAIC_12_NFB4EOF_ERR ,DMAIC 12 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 11. " DMAIC_11_NFB4EOF_ERR ,DMAIC 11 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 10. " DMAIC_10_NFB4EOF_ERR ,DMAIC 10 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 9. " DMAIC_9_NFB4EOF_ERR ,DMAIC 9 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 8. " DMAIC_8_NFB4EOF_ERR ,DMAIC 8 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 7. " DMAIC_7_NFB4EOF_ERR ,DMAIC 7 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 6. " DMAIC_6_NFB4EOF_ERR ,DMAIC 6 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 5. " DMAIC_5_NFB4EOF_ERR ,DMAIC 5 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 4. " DMAIC_4_NFB4EOF_ERR ,DMAIC 4 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 3. " DMAIC_3_NFB4EOF_ERR ,DMAIC 3 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 2. " DMAIC_2_NFB4EOF_ERR ,DMAIC 2 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0xC 1. " DMAIC_1_NFB4EOF_ERR ,DMAIC 1 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
eventfld.long 0xC 0. " DMAIC_0_NFB4EOF_ERR ,DMAIC 0 _NFB4EOF_ERR" "No interrupt,Interrupt"
|
|
line.long 0x10 "IPU_INT_STAT_5,IPU Interrupt Status Register 5"
|
|
bitfld.long 0x10 16. " SAHB_ADDR_ERR ,Status of the SAHB_ADDR_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 15. " DI_LLA_LOCK_ERR ,Status of the DI_LLA_LOCK_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 14. " DI_ADC_LOCK_ERR ,Status of DI_ADC_LOCK_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 13. " VF_FRM_LOST_ERR ,Status of VF_FRM_LOST_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 12. " ENC_FRM_LOST_ERR ,Status of ENC_FRM_LOST_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 11. " BAYER_FRM_LOST_ERR ,Status of BAYER_FRM_LOST_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 10. " SDC_MSKD_ERR ,Status of SDC_MSK_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 9. " SDC_FGD_ERR ,Status of SDC_FGD_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 8. " SDC_BGD_ERR ,Status of SDC_BGD_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 7. " AHB_M2_ERR ,Status of AHB_M2_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 6. " AHB_M1_ERR ,Status of AHB_M1_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 5. " ADC_SYS2_TEARING_ERR ,Status of ADC_SYS2_TEARING_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 4. " ADC_SYS1_TEARING_ERR ,Status of ADC_SYS1_TEARING_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 3. " ADC_PP_TEARING_ERR ,Status of ADC_PP_TEARING_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 2. " VF_BUF_OVF_ERR ,Status of VF_BUF_OVF_ERR interrupt" "No interrupt,Interrupt"
|
|
eventfld.long 0x10 1. " ENC_BUF_OVF_ERR ,Status of ENC_BUF_OVF_ERR interrupt" "No interrupt,Interrupt"
|
|
textline " "
|
|
eventfld.long 0x10 0. " BAYER_BUF_OVF_ERR ,Status of BAYER_BUF_OVF_ERR interrupt" "No interrupt,Interrupt"
|
|
tree.end
|
|
tree "IPU Break Registers"
|
|
textline " "
|
|
group.long 0x50++0x7
|
|
line.long 0x00 "IPU_BRK_CTRL_1,IPU Break Control Register 1"
|
|
hexmask.long.byte 0x00 24.--31. 1. " BRK_EVNT_NUM ,Break event number minus 1"
|
|
bitfld.long 0x00 21.--23. " BRK_GRP_SEL ,Break group select" "Group 0,Group 1,Group 2,Group 3,Group 4,?..."
|
|
textline " "
|
|
bitfld.long 0x00 16.--20. " BRK_SIG_SEL ,Break signal select" "DMA stop,Freeze,Interrupt,?..."
|
|
bitfld.long 0x00 12. " SDC_DBG_MASK_DIS ,SDC debug mode channel mask disable" "Masked,Not masked"
|
|
textline " "
|
|
bitfld.long 0x00 11. " BRK_SIG_COND_EN ,Break on signal posedge enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " BRK_COL_COND_EN ,Break on column number enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " BRK_ROW_COND_EN ,Break on row number enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " BRK_CHA_COND_EN ,Break on channel number enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " BRK_RQ_MODE ,Break request mode" "DMA stop,Freeze,Interrupt,?..."
|
|
bitfld.long 0x00 5. " DBG_ENTER_MODE0 ,Debug entering mode 0" "Forced,Not forced"
|
|
textline " "
|
|
bitfld.long 0x00 4. " DBG_ENTER_MODE1 ,Debug entering mode 1" "Forced,Not forced"
|
|
bitfld.long 0x00 2. " DBG_EXIT ,Exit debug mode" "Not exited,Exited"
|
|
textline " "
|
|
bitfld.long 0x00 1. " FRC_DBG ,Force entering debug mode" "Not forced,Forced"
|
|
bitfld.long 0x00 0. " BRK_EN ,Break enable" "Disabled,Enabled"
|
|
line.long 0x04 "IPU_BRK_CTRL_2,IPU Break Control Register 2"
|
|
bitfld.long 0x04 31. " CSI_CHA_EN ,Enable CSI break condition" "Disabled,Enabled"
|
|
bitfld.long 0x04 26.--30. " BRK_CHA_NUM ,DMA channel number for break condition" "Channel 0,Channel 1,Channel 2,Channel 3,Channel 4,Channel 5,Channel 6,Channel 7,Channel 8,Channel 9,Channel 10,Channel 11,Channel 12,Channel 13,Channel 14,Channel 15,Channel 16,Channel 17,Channel 18,Channel 19,Channel 20,Channel 21,Channel 22,Channel 23,Channel 24,Channel 25,Channel 26,Channel 27,Channel 28,Channel 29,Channel 30,Channel 31"
|
|
textline " "
|
|
hexmask.long.word 0x04 13.--24. 1. " BRK_COL_NUM[11:0] ,Frame column number for break condition"
|
|
hexmask.long.word 0x04 0.--12. 1. " BRK_ROW_NUM ,Frame row number for break condition"
|
|
rgroup.long 0x58++0x3
|
|
line.long 0x00 "IPU_BRK_STAT,IPU Break Status Register"
|
|
bitfld.long 0x00 2. " BRK_SRC ,IPU break acknowledge" "Not acknowledged,Acknowledged"
|
|
bitfld.long 0x00 1. " MCU_DBGRQ ,MCU debug request" "Not requested,Requested"
|
|
textline " "
|
|
bitfld.long 0x00 0. " IPU_BREAK_ACK ,Break source" "External,Internal"
|
|
tree.end
|
|
textline " "
|
|
group.long 0x5c++0x3
|
|
line.long 0x00 "IPU_DIAGB_CTRL,IPU Diagnostic Bus Control Register"
|
|
bitfld.long 0x00 0.--4. " MON_GRP_SEL ,Select group of signales to be output via the Diagnostic Bus" "ADC,CSI,DI,IC,PF,SDC,IDMAC/transfer,IDMAC/line,IDMAC/burst,IDMAC/new frame,IDMAC,IPU_CHA_BUF0_RDY,IPU_CHA_BUF1_RDY,IPU_CHA_CUR_BUF,IPU_TASKS_STAT,IPU_INT_STAT_3,IPU_INT_STAT_4,IPU_INT_STAT_5,IDMAC_CHA_BUSY,?..."
|
|
tree.end
|
|
width 0x14
|
|
tree "CSI Registers"
|
|
group.long 0x60++0x27
|
|
line.long 0x00 "CSI_SENS_CONF,CSI Sensor Configuration Register"
|
|
hexmask.long.byte 0x0 16.--23. 1. " DIV_RATIO ,Clock division ratio minus 1"
|
|
bitfld.long 0x00 15. " EXT_VSYNC ,External VSYNC enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " DATA_WIDTH ,Data width" "2x4-bit,8 bits,10 bits,15 bits"
|
|
bitfld.long 0x00 8.--9. " SENS_DATA_FORMAT ,Data format from the sensor" "RGB/YUV444,Reserved,YUV422,Bayer/generic"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SENS_CLK_SRC ,Sensor clock source" "SENSB_SENS_CLK,HSP_CLK"
|
|
bitfld.long 0x00 4.--5. " SENS_PRTCL ,Sensor protocol" "Gated clock,Non-gated clock,CCIR progressive,CCIR interlaced"
|
|
textline " "
|
|
bitfld.long 0x00 3. " SENS_PIX_CLK_POL ,Invert pixel clock input" "Not inverted,Inverted"
|
|
bitfld.long 0x00 2. " DATA_POL ,Invert data input" "Not inverted,Inverted"
|
|
textline " "
|
|
bitfld.long 0x00 1. " HSYNC_POL ,Invert IPP_IND_SENSB_HSYNC input" "Not inverted,Inverted"
|
|
bitfld.long 0x00 0. " VSYNC_POL ,Invert IPP_IND_SENSB_VSYNC input" "Not inverted,Inverted"
|
|
line.long 0x04 "CSI_SENS_FRM_SIZE,CSI Sensor Frame Size Register"
|
|
hexmask.long.word 0x04 16.--27. 1. " SENS_FRM_HEIGHT ,Sensor frame height minus 1"
|
|
hexmask.long.word 0x04 0.--11. 1. " SENS_FRM_WIDTH ,Sensor frame width minus 1"
|
|
line.long 0x08 "CSI_ACT_FRM_SIZE,CSI Actual Frame Size Register"
|
|
hexmask.long.word 0x08 16.--27. 1. " ACT_FRM_HEIGHT ,Actual frame height minus 1"
|
|
hexmask.long.word 0x08 0.--11. 1. " ACT_FRM_WIDTH ,Actual frame width minus 1"
|
|
line.long 0x0c "CSI_OUT_FRM_CTRL,CSI Output Frame Control Register"
|
|
bitfld.long 0x0c 29. " HORZ_DWNS ,Enable horizontal downsizing (decimation) by 2" "Disabled,Enabled"
|
|
bitfld.long 0x0c 28. " VERT_DWNS ,Enable vertical downsizing (decimation) by 2" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0c 26. " IC_TV_MODE ,Convert interlaced frame format to progressive frame format" "Not converted,Converted"
|
|
bitfld.long 0x0c 25. " SKIP_VF4 ,Skip viewfinder frame 4" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x0c 24. " SKIP_VF3 ,Skip viewfinder frame 3" "Not skipped,Skipped"
|
|
bitfld.long 0x0c 23. " SKIP_VF2 ,Skip viewfinder frame 2" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x0c 22. " SKIP_VF1 ,Skip viewfinder frame 1" "Not skipped,Skipped"
|
|
bitfld.long 0x0c 21. " SKIP_VF0 ,Skip viewfinder frame 0" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x0c 20. " SKIP_ENC4 ,Skip encoder frame 4" "Not skipped,Skipped"
|
|
bitfld.long 0x0c 19. " SKIP_ENC3 ,Skip encoder frame 3" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x0c 18. " SKIP_ENC2 ,Skip encoder frame 2" "Not skipped,Skipped"
|
|
bitfld.long 0x0c 17. " SKIP_ENC1 ,Skip encoder frame 1" "Not skipped,Skipped"
|
|
textline " "
|
|
bitfld.long 0x0c 16. " SKIP_ENC0 ,Skip encoder frame 0" "Not skipped,Skipped"
|
|
hexmask.long.byte 0x0c 8.--15. 1. " HSC ,Horizontal skip"
|
|
textline " "
|
|
hexmask.long.byte 0x0c 0.--7. 1. " VSC ,Vertical skip"
|
|
line.long 0x10 "CSI_TST_CTRL,CSI Test Control Register"
|
|
bitfld.long 0x10 24. " TEST_GEN_MODE ,Test generator mode" "Inactive,Active"
|
|
hexmask.long.byte 0x10 16.--23. 1. " PG_B_VALUE ,Pattern generator B value"
|
|
textline " "
|
|
hexmask.long.byte 0x10 8.--15. 1. " PG_G_VALUE ,Pattern generator G value"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PG_R_VALUE ,Pattern generator R value"
|
|
line.long 0x14 "CSI_CCIR_CODE_1,CSI CCIR Code Register 1"
|
|
bitfld.long 0x14 24. " CCIR_ERR_DET_EN ,Enable error detection and correction for CCIR interlaced mode with protection bit" "Disabled,Enabled"
|
|
bitfld.long 0x14 19.--21. " STRT_FLD0_ACTV ,Start of field 0 active line command" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x14 16.--18. " END_FLD0_ACTV ,End of field 0 active line command" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x14 9.--11. " STRT_FLD0_BLNK_2ND ,Start of field 0 second blanking line command" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x14 6.--8. " END_FLD0_BLNK_2ND ,End of field 0 second blanking line command" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x14 3.--5. " STRT_FLD0_BLNK_1ST ,Start of field 0 first blanking line command" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x14 0.--2. " END_FLD0_BLNK_1ST ,End of field 0 first blanking line command" "0,1,2,3,4,5,6,7"
|
|
line.long 0x18 "CSI_CCIR_CODE_2,CSI_CCIR Code Register 2"
|
|
bitfld.long 0x18 19.--21. " STRT_FLD1_ACTV ,Start of field 1 active line command" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x18 16.--18. " END_FLD1_ACTV ,End of field 1 active line command" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x18 9.--11. " STRT_FLD1_BLNK_2ND ,Start of field 1 second blanking line command" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x18 6.--8. " END_FLD1_BLNK_2ND ,End of field 1 second blanking line command" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x18 3.--5. " STRT_FLD1_BLNK_1ST ,Start of field 1 first blanking line command" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x18 0.--2. " END_FLD1_BLNK_1ST ,End of field 1 first blanking line command" "0,1,2,3,4,5,6,7"
|
|
line.long 0x1c "CSI_CCIR_CODE_3,CSI CCIR Code Register 3"
|
|
hexmask.long.tbyte 0x1c 0.--23. 1. " CCIR_PRECOM[23:0] ,CCIR pre command"
|
|
line.long 0x20 "CSI_FLASH_STROBE_1,CSI Flash Strobe Register 1"
|
|
hexmask.long.word 0x20 16.--31. 1. " SENS_ROW_DURATION ,Duration of sensor row minus 1"
|
|
bitfld.long 0x20 0. " CLOCK_SEL ,Select clock for sensor row duration count" "SENSB_MCLK,SENSB_PIX_CLK"
|
|
line.long 0x24 "CSI_FLASH_STROBE_2,CSI Flash Strobe Register 2"
|
|
hexmask.long.word 0x24 16.--31. 1. " STROBE_DURATION ,Strobe Duration minus 1"
|
|
hexmask.long.word 0x24 3.--15. 1. " STROBE_START_TIME ,Strobe start time minus 1"
|
|
textline " "
|
|
bitfld.long 0x24 1. " STROBE_POL ,Strobe polarity control bit" "Low,High"
|
|
bitfld.long 0x24 0. " STROBE_EN ,Strobe enable control/status bit" "Disabled,Enabled"
|
|
tree.end
|
|
width 0x10
|
|
tree "IC Registers"
|
|
group.long 0x88++0x17
|
|
line.long 0x00 "IC_CONF,IC Configuration Register"
|
|
bitfld.long 0x00 31. " CSI_MEM_WR_EN ,CSI direct memory write enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 30. " RWS_EN ,Raw sensor enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 29. " IC_KEY_COLOR_EN ,Key color enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 28. " IC_GLB_LOC_A ,Global alpha" "Local,Global"
|
|
textline " "
|
|
bitfld.long 0x00 20. " PP_ROT_EN ,Post-processing rotation task enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " PP_CMB ,Post-processing task combining enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " PP_CSC2 ,Post-processing task color conversion RGB-->YUV enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " PP_CSC1 ,Post-processing task color conversion YUV-->RGB enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 16. " PP_EN ,Post-processing task enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " PRPVF_ROT_EN ,Preprocessing rotation task for viewfinder enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 11. " PRPVF_CMB ,Preprocessing task for view-finder combining enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " PRPVF_CSC2 ,Pre-processing task for view-finder second color conversion enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " PRPVF_CSC1 ,Pre-processing task for view-finder first color conversion enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " PRPVF_EN ,Preprocessing task for view-finder enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 2. " PRPENC_ROT_EN ,Preprocessing rotation task for encoding enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " PRPENC_CSC1 ,Preprocessing task for encoding color conversion enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " PRPENC_EN ,Preprocessing task for encoding enable" "Disabled,Enabled"
|
|
line.long 0x04 "IC_PRP_ENC_RSC,IC Preprocessing Encoder Resizing Coefficients Register"
|
|
bitfld.long 0x04 30.--31. " PRPENC_DS_R_V ,Preprocessing task for encoding downsizing vertical ratio" "0,1,2,3"
|
|
hexmask.long.word 0x04 16.--29. 1. " PRPENC_RS_R_V ,Preprocessing task for encoding resizing vertical ratio"
|
|
textline " "
|
|
bitfld.long 0x04 14.--15. " PRPENC_DS_R_H ,Preprocessing task for encoding downsizing horizontal ratio" "1,2,4,?..."
|
|
hexmask.long.word 0x04 0.--13. 1. " PRPENC_RS_R_H ,Preprocessing task for encoding resizing horizontal ratio"
|
|
line.long 0x08 "IC_PRP_VF_RSC,IC Preprocessing View-Finder Resizing Coefficients Register"
|
|
bitfld.long 0x08 30.--31. " PRPVF_DS_R_V ,Preprocessing task for encoding downsizing vertical ratio" "0,1,2,3"
|
|
hexmask.long.word 0x08 16.--29. 1. " PRPVF_RS_R_V ,Preprocessing task for encoding resizing vertical ratio"
|
|
textline " "
|
|
bitfld.long 0x08 14.--15. " PRPVF_DS_R_H ,Preprocessing task for encoding downsizing horizontal ratio" "1,2,4,?..."
|
|
hexmask.long.word 0x08 0.--13. 1. " PRPVF_RS_R_H ,Preprocessing task for view-finding resizing horizontal ratio"
|
|
line.long 0x0c "IC_PP_RSC,IC Post-Processing Resizing Coefficients Register"
|
|
bitfld.long 0x0c 30.--31. " PP_DS_R_V ,Post-processing task downsizing vertical ratio" "0,1,2,3"
|
|
hexmask.long.word 0x0c 16.--29. 1. " PP_RS_R_V ,Post-processing task resizing vertical ratio"
|
|
textline " "
|
|
bitfld.long 0x0c 14.--15. " PP_DS_R_H ,Post-processing task downsizing horizontal ratio" "1,2,4,?..."
|
|
hexmask.long.word 0x0c 0.--13. 1. " PP_RS_R_H ,Post-processing task resizing horizontal ratio"
|
|
line.long 0x10 "IC_CMBP_1,IC Combining Parameters Register 1"
|
|
hexmask.long.byte 0x10 8.--15. 1. " IC_PP_ALPHA_V ,Post-processing task global alpha"
|
|
hexmask.long.byte 0x10 0.--7. 1. " IC_PRPVF_ALPHA_V ,Preprocessing task for encoding global alpha"
|
|
line.long 0x14 "IC_CMBP_2,IC Combining Parameters Register 2"
|
|
hexmask.long.byte 0x14 16.--23. 1. " IC_KEY_COLOR_R ,Key color red"
|
|
hexmask.long.byte 0x14 8.--15. 1. " IC_KEY_COLOR_G ,Key color green"
|
|
textline " "
|
|
hexmask.long.byte 0x14 0.--7. 1. " IC_KEY_COLOR_B ,Key color blue"
|
|
tree.end
|
|
width 0x9
|
|
tree "PF (Post Filter Register)"
|
|
group.long 0xa0++0x3
|
|
line.long 0x00 "PF_CONF,Post Filter (PF) Configuration Register"
|
|
hexmask.long.byte 0x00 16.--21. 1. " H264_Y_PAUSE_ROW ,Y input frame before pause last row number"
|
|
bitfld.long 0x00 4. " H264_Y_PAUSE_EN ,PF pause in H.264 mode during processing Y component enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0.--2. " PF_TYPE ,Post filtering type" "Disabled,MPEG-4 Deblocking,MPEG-4 Deringing,MPEG-4 Deblocking/Deringing,H.264 Deblocking,?..."
|
|
tree.end
|
|
width 0x10
|
|
tree "IDMAC Registers"
|
|
group.long 0xa4++0xb
|
|
line.long 0x00 "IDMAC_CONF,IDMAC Configuration Register"
|
|
bitfld.long 0x00 8. " SINGLE_AHB_M_EN ,Enable single master AHB" "Disabled,Enabled"
|
|
bitfld.long 0x00 4.--6. " SRCNT ,Service request counter" "1 request,2 requests,3 requests,4 requests,5 requests,6 requests,7 requests,8 requests"
|
|
textline " "
|
|
bitfld.long 0x00 0.--1. " PRYM ,Priority mode" "Round robin,Random,Read after write,?..."
|
|
line.long 0x04 "IDMAC_CHA_EN,IDMAC Channel Enable Register"
|
|
bitfld.long 0x4 31. " DMAPF_7_EN ,DMAPF 7 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 30. " DMAPF_6_EN ,DMAPF 6 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 29. " DMAPF_5_EN ,DMAPF 5 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 28. " DMAPF_4_EN ,DMAPF 4 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 27. " DMAPF_3_EN ,DMAPF 3 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 26. " DMAPF_2_EN ,DMAPF 2 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 25. " DMAPF_1_EN ,DMAPF 1 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 24. " DMAPF_0_EN ,DMAPF 0 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 23. " DMAADC_7_EN ,DMAADC 7 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 22. " DMAADC_6_EN ,DMAADC 6 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 21. " DMAADC_5_EN ,DMAADC 5 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 20. " DMAADC_4_EN ,DMAADC 4 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 19. " DMAADC_3_EN ,DMAADC 3 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 18. " DMAADC_2_EN ,DMAADC 2 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 17. " DMASDC_3_EN ,DMASDC 3 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 16. " DMASDC_2_EN ,DMASDC 2 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 15. " DMASDC_1_EN ,DMASDC 1 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 14. " DMASDC_0_EN ,DMASDC 0 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 13. " DMAIC_13_EN ,DMAIC 13 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 12. " DMAIC_12_EN ,DMAIC 12 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 11. " DMAIC_11_EN ,DMAIC 11 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 10. " DMAIC_10_EN ,DMAIC 10 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 9. " DMAIC_9_EN ,DMAIC 9 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 8. " DMAIC_8_EN ,DMAIC 8 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 7. " DMAIC_7_EN ,DMAIC 7 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 6. " DMAIC_6_EN ,DMAIC 6 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 5. " DMAIC_5_EN ,DMAIC 5 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 4. " DMAIC_4_EN ,DMAIC 4 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 3. " DMAIC_3_EN ,DMAIC 3 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 2. " DMAIC_2_EN ,DMAIC 2 DMA channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x4 1. " DMAIC_1_EN ,DMAIC 1 DMA channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x4 0. " DMAIC_0_EN ,DMAIC 0 DMA channel enable" "Disabled,Enabled"
|
|
line.long 0x08 "IDMAC_CHA_PRI,IDMAC Channel Priority Register"
|
|
bitfld.long 0x8 31. " DMAPF_7_PRI ,DMAPF 7 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 30. " DMAPF_6_PRI ,DMAPF 6 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 29. " DMAPF_5_PRI ,DMAPF 5 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 28. " DMAPF_4_PRI ,DMAPF 4 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 27. " DMAPF_3_PRI ,DMAPF 3 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 26. " DMAPF_2_PRI ,DMAPF 2 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 25. " DMAPF_1_PRI ,DMAPF 1 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 24. " DMAPF_0_PRI ,DMAPF 0 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 23. " DMAADC_7_PRI ,DMAADC 7 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 22. " DMAADC_6_PRI ,DMAADC 6 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 21. " DMAADC_5_PRI ,DMAADC 5 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 20. " DMAADC_4_PRI ,DMAADC 4 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 19. " DMAADC_3_PRI ,DMAADC 3 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 18. " DMAADC_2_PRI ,DMAADC 2 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 17. " DMASDC_3_PRI ,DMASDC 3 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 16. " DMASDC_2_PRI ,DMASDC 2 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 15. " DMASDC_1_PRI ,DMASDC 1 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 14. " DMASDC_0_PRI ,DMASDC 0 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 13. " DMAIC_13_PRI ,DMAIC 13 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 12. " DMAIC_12_PRI ,DMAIC 12 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 11. " DMAIC_11_PRI ,DMAIC 11 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 10. " DMAIC_10_PRI ,DMAIC 10 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 9. " DMAIC_9_PRI ,DMAIC 9 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 8. " DMAIC_8_PRI ,DMAIC 8 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 7. " DMAIC_7_PRI ,DMAIC 7 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 6. " DMAIC_6_PRI ,DMAIC 6 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 5. " DMAIC_5_PRI ,DMAIC 5 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 4. " DMAIC_4_PRI ,DMAIC 4 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 3. " DMAIC_3_PRI ,DMAIC 3 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 2. " DMAIC_2_PRI ,DMAIC 2 DMA channel priority" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x8 1. " DMAIC_1_PRI ,DMAIC 1 DMA channel priority" "Low,High"
|
|
bitfld.long 0x8 0. " DMAIC_0_PRI ,DMAIC 0 DMA channel priority" "Low,High"
|
|
rgroup.long 0xb0++0x3
|
|
line.long 0x00 "IDMAC_CHA_BUSY,IDMAC Channel Busy Register"
|
|
bitfld.long 0x0 31. " DMAPF_7_BUSY ,DMAPF 7 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 30. " DMAPF_6_BUSY ,DMAPF 6 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 29. " DMAPF_5_BUSY ,DMAPF 5 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 28. " DMAPF_4_BUSY ,DMAPF 4 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 27. " DMAPF_3_BUSY ,DMAPF 3 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 26. " DMAPF_2_BUSY ,DMAPF 2 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 25. " DMAPF_1_BUSY ,DMAPF 1 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 24. " DMAPF_0_BUSY ,DMAPF 0 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 23. " DMAADC_7_BUSY ,DMAADC 7 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 22. " DMAADC_6_BUSY ,DMAADC 6 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 21. " DMAADC_5_BUSY ,DMAADC 5 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 20. " DMAADC_4_BUSY ,DMAADC 4 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 19. " DMAADC_3_BUSY ,DMAADC 3 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 18. " DMAADC_2_BUSY ,DMAADC 2 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 17. " DMASDC_3_BUSY ,DMASDC 3 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 16. " DMASDC_2_BUSY ,DMASDC 2 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 15. " DMASDC_1_BUSY ,DMASDC 1 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 14. " DMASDC_0_BUSY ,DMASDC 0 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 13. " DMAIC_13_BUSY ,DMAIC 13 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 12. " DMAIC_12_BUSY ,DMAIC 12 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 11. " DMAIC_11_BUSY ,DMAIC 11 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 10. " DMAIC_10_BUSY ,DMAIC 10 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 9. " DMAIC_9_BUSY ,DMAIC 9 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 8. " DMAIC_8_BUSY ,DMAIC 8 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 7. " DMAIC_7_BUSY ,DMAIC 7 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 6. " DMAIC_6_BUSY ,DMAIC 6 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 5. " DMAIC_5_BUSY ,DMAIC 5 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 4. " DMAIC_4_BUSY ,DMAIC 4 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 3. " DMAIC_3_BUSY ,DMAIC 3 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 2. " DMAIC_2_BUSY ,DMAIC 2 Ready" "Ready,Not ready"
|
|
textline " "
|
|
bitfld.long 0x0 1. " DMAIC_1_BUSY ,DMAIC 1 Ready" "Ready,Not ready"
|
|
bitfld.long 0x0 0. " DMAIC_0_BUSY ,DMAIC 0 Ready" "Ready,Not ready"
|
|
tree.end
|
|
width 0x18
|
|
tree "SDC Registers"
|
|
group.long 0xb4++0x2b
|
|
line.long 0x00 "SDC_COM_CONF,SDC Common Configuration Register"
|
|
bitfld.long 0x00 16.--18. " COC ,Cursor operation control" "Transparent,Full,Reversed,AND,Reserved,OR,XOR,?..."
|
|
bitfld.long 0x00 15. " DUAL_MODE ,Dual mode enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 14. " SAVE_REFR_EN ,Enable saving refresh mode" "Disabled,Enabled"
|
|
bitfld.long 0x00 12. " SHARP ,Sharp panel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " BG_EN ,Background enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " MASK_EN ,Mask enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SDC_KEY_COLOR_EN ,Graphic window color keying enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " SDC_GLB_LOC_A ,Graphic window alpha mode" "Local,Global"
|
|
textline " "
|
|
bitfld.long 0x00 5. " GWSEL ,Graphic window select" "Background,Foreground"
|
|
bitfld.long 0x00 4. " FG_EN ,Foreground enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " FG_MCP_FORM ,Foreground monochrome data format" "8 bpp,16 bpp"
|
|
bitfld.long 0x00 2. " BG_MCP_FORM ,Background monochrome data format" "8 bpp,16 bpp"
|
|
textline " "
|
|
bitfld.long 0x00 0.--1. " SDC_MODE ,SDC mode" "Monochrome,Color,Progressive,Interlaced"
|
|
line.long 0x04 "SDC_GRAPH_WIND_CTRL,SDC Graphic Window Control Register"
|
|
hexmask.long.byte 0x04 24.--31. 1. " SDC_ALPHA_V ,Graphic window alpha value"
|
|
hexmask.long.byte 0x04 16.--23. 1. " SDC_KEY_COLOR_R ,Graphic window color keying red component"
|
|
textline " "
|
|
hexmask.long.byte 0x04 8.--15. 1. " SDC_KEY_COLOR_G ,Graphic window color keying green component"
|
|
hexmask.long.byte 0x04 0.--7. 1. " SDC_KEY_COLOR_B ,Graphic window color keying blue component"
|
|
line.long 0x08 "SDC_FG_POS,SDC Foreground Window Position Register"
|
|
hexmask.long.word 0x08 16.--25. 1. " FGXP ,Foreground window X position"
|
|
hexmask.long.word 0x08 0.--9. 1. " FGYP ,Foreground window Y position"
|
|
line.long 0x0c "SDC_BG_POS,SDC Background Window Position Register"
|
|
hexmask.long.word 0x0c 16.--25. 1. " BGXP ,Background window X position"
|
|
hexmask.long.word 0x0c 0.--9. 1. " BGYP ,Background window Y position"
|
|
line.long 0x10 "SDC_CUR_POS,SDC Cursor Position Register"
|
|
bitfld.long 0x10 26.--30. " CXW ,Cursor width minus 1" "1 pixel,2 pixels,3 pixels,4 pixels,5 pixels,6 pixels,7 pixels,8 pixels,9 pixels,10 pixels,11 pixels,12 pixels,13 pixels,14 pixels,15 pixels,16 pixels,17 pixels,18 pixels,19 pixels,20 pixels,21 pixels,22 pixels,23 pixels,24 pixels,25 pixels,26 pixels,27 pixels,28 pixels,29 pixels,30 pixels,31 pixels,32 pixels"
|
|
hexmask.long.word 0x10 16.--25. 1. " CXP ,Cursor X position"
|
|
textline " "
|
|
bitfld.long 0x10 10.--14. " CYH ,Cursor height minus 1" "1 pixel,2 pixels,3 pixels,4 pixels,5 pixels,6 pixels,7 pixels,8 pixels,9 pixels,10 pixels,11 pixels,12 pixels,13 pixels,14 pixels,15 pixels,16 pixels,17 pixels,18 pixels,19 pixels,20 pixels,21 pixels,22 pixels,23 pixels,24 pixels,25 pixels,26 pixels,27 pixels,28 pixels,29 pixels,30 pixels,31 pixels,32 pixels"
|
|
hexmask.long.word 0x10 0.--9. 1. " CYP ,Cursor Y position"
|
|
line.long 0x14 "SDC_CUR_BLINK_PWM_CTRL,SDC Cursor Blinking and PWM Contrast Control Register"
|
|
bitfld.long 0x14 25.--26. " SCR ,Source select" "HSYNC,Pixel,HSP_CLK,?..."
|
|
bitfld.long 0x14 24. " CC_EN ,Contrast control enable" "Disabled,Enabled"
|
|
textline " "
|
|
hexmask.long.byte 0x14 16.--23. 1. " PWM ,Pulse width minus 1"
|
|
bitfld.long 0x14 15. " BK_EN ,Blinking enable" "Disabled,Enabled"
|
|
textline " "
|
|
hexmask.long.byte 0x14 0.--7. 1. " BKDIV ,Blink divisor minus 1"
|
|
line.long 0x18 "SDC_CUR_MAP,SDC Color Cursor Mapping Register"
|
|
hexmask.long.byte 0x18 16.--23. 1. " CUR_COL_R ,Cursor red field"
|
|
hexmask.long.byte 0x18 8.--15. 1. " CUR_COL_G ,Cursor green field"
|
|
textline " "
|
|
hexmask.long.byte 0x18 0.--7. 1. " CUR_COL_B ,Cursor blue field"
|
|
line.long 0x1C "SDC_HOR_CONF,SDC Horizontal Configuration Register"
|
|
hexmask.long.byte 0x1C 26.--31. 1. " H_SYNC_WIDTH ,Horizontal synchronization pulse width minus 1"
|
|
hexmask.long.word 0x1C 16.--25. 1. " SCREEN_WIDTH ,Screen width minus 1"
|
|
textline " "
|
|
bitfld.long 0x1C 0.--3. " H_SYNC_DELAY ,Horizontal synchronization pulse delay" "No periods,1 period,2 periods,3 periods,4 periods,5 periods,6 periods,7 periods,8 periods,9 periods,10 periods,11 periods,12 periods,13 periods,14 periods,15 periods"
|
|
line.long 0x20 "SDC_VER_CONF,SDC Vertical Configuration Register"
|
|
hexmask.long.byte 0x20 26.--31. 1. " V_SYNC_WIDTH ,Vertical synchronization pulse width minus 1"
|
|
hexmask.long.word 0x20 16.--25. 1. " SCREEN_HEIGHT ,Screen height minus 1"
|
|
textline " "
|
|
bitfld.long 0x20 0. " V_SYNC_WIDTH_L ,Vertical synchronization pulse width units" "Pixels,Rows"
|
|
line.long 0x24 "SDC_SHARP_CONF_1,SDC Sharp Configuration Register 1"
|
|
hexmask.long.word 0x24 16.--25. 1. " REV_TOGGLE_DELAY ,REV toggle delay"
|
|
hexmask.long.byte 0x24 8.--15. 1. " PS_FALL_DELAY ,PS fall delay relative to LP rising edge"
|
|
textline " "
|
|
hexmask.long.byte 0x24 0.--7. 1. " CLS_RISE_DELAY ,CLS rise delay relative to LP rising edge"
|
|
line.long 0x28 "SDC_SHARP_CONF_2,SDC Sharp Configuration Register 2"
|
|
hexmask.long.word 0x28 16.--25. 1. " PS_RISE_DELAY ,PS rise delay relative to LP rising edge"
|
|
hexmask.long.word 0x28 0.--9. 1. " CLS_FALL_DELAY ,CLS fall delay relative to LP rising edge"
|
|
tree.end
|
|
width 0x11
|
|
tree "ADC Registers"
|
|
group.long 0xe0++0x43
|
|
line.long 0x00 "ADC_CONF,ADC Configuration Register"
|
|
bitfld.long 0x00 31. " SYS2_DATA_MAP ,Select data mapping rule for the system channel 2" "Data,Command"
|
|
bitfld.long 0x00 29.--30. " SYS2_ADDR_INC ,Address increment for the system channel 2" "By 1,By 2,Reserved,By 4"
|
|
textline " "
|
|
bitfld.long 0x00 27.--28. " SYS2_DISP_NUM ,Display number for system channel 2" "Display 0,Display 1,Display 2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 24.--26. " SYS2_MODE ,Control sequence generation mode for system channel 2" "Disabled,Write in template/not sequential,Read in template/not sequential,Write in template/each access,Read in template/each access,Write data/RS=0,Write data/RS=1,Write in command"
|
|
textline " "
|
|
bitfld.long 0x00 23. " SYS1_DATA_MAP ,Select data mapping rule for the system channel 1" "Data,Command"
|
|
bitfld.long 0x00 21.--22. " SYS1_ADDR_INC ,Address increment for the system channel 1" "By 1,By 2,Reserved,By 4"
|
|
textline " "
|
|
bitfld.long 0x00 19.--20. " SYS1_DISP_NUM ,Display number for system channel 1" "Display 0,Display 1,Display 2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 16.--18. " SYS1_MODE ,Control sequence generation mode for system channel 1" "Disabled,Write in template/not sequential,Read in template/not sequential,Write in template/each access,Read in template/each access,Write data/RS=0,Write data/RS=1,Write in command"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SYS2_NO_TEARING ,Display line synchronization to avoid tearing enable" "Not synchronized,Synchronized"
|
|
textline " "
|
|
bitfld.long 0x00 14. " SYS1_NO_TEARING ,Display line synchronization to avoid tearing enable" "Not synchronized,Synchronized"
|
|
textline " "
|
|
bitfld.long 0x00 13. " PP_NO_TEARING ,Display line synchronization to avoid tearing enable" "Not synchronized,Synchronized"
|
|
bitfld.long 0x00 12. " PP_DATA_MAP ,Select data mapping rule for the post-processing channel" "Data,Command"
|
|
textline " "
|
|
bitfld.long 0x00 10.--11. " PP_ADDR_INC ,Post-processing channel display address increment per display access" "By 1,By 2,Reserved,By 4"
|
|
bitfld.long 0x00 8.--9. " PP_DISP_NUM ,Post-processing channel display number" "Display 0,Display 1,Display 2,?..."
|
|
textline " "
|
|
bitfld.long 0x00 7. " PRP_DATA_MAP ,Select data mapping rule for the pre-processing channel" "Data,Command"
|
|
bitfld.long 0x00 5.--6. " PRP_ADDR_INC ,Pre-processing channel display address increment per display access" "By 1,By 2,Reserved,By 4"
|
|
textline " "
|
|
bitfld.long 0x00 3.--4. " PRP_DISP_NUM ,Pre-processing channel display number" "Display 0,Display 1,Display 2,?..."
|
|
bitfld.long 0x00 2. " MCU_CHAN_EN ,MCU channel enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " PP_CHAN_EN ,Post-processing channel enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " PRP_CHAN_EN ,Pre-processing channel enable" "Disabled,Enabled"
|
|
line.long 0x04 "ADC_SYSCHA1_SA,ADC System Channel 1 Start Address Register"
|
|
hexmask.long.word 0x04 23.--31. 1. " SYS1_START_TIME ,Delay between display vertical synchronization pulse and start time point of system channel 1 window"
|
|
hexmask.long.tbyte 0x04 0.--22. 1. " SYS1_CHAN_SA[22:0] ,System channel 1 start address"
|
|
line.long 0x08 "ADC_SYSCHA2_SA,ADC System Channel 2 Start Address Register"
|
|
hexmask.long.word 0x08 23.--31. 1. " SYS2_START_TIME ,Delay between display vertical synchronization pulse and start time point of system channel 1 window"
|
|
hexmask.long.tbyte 0x08 0.--22. 1. " SYS2_CHAN_SA[22:0] ,Channel 2 start address"
|
|
line.long 0x0c "ADC_PRPCHAN_SA,ADC Preprocessing Channel Start Address Register"
|
|
hexmask.long.tbyte 0x0c 0.--22. 1. " PRP_CHAN_SA[22:0] ,PRP start address"
|
|
line.long 0x10 "ADC_PPCHAN_SA,ADC Post-Processing Channel Start Address Register"
|
|
hexmask.long.word 0x10 23.--31. 1. " PP_START_TIME ,Delay between display vertical synchronization pulse and start time point of system channel 1 window"
|
|
hexmask.long.tbyte 0x10 0.--22. 1. " PP_CHAN_SA[22:0] ,PP start address"
|
|
line.long 0x14 "ADC_DISP0_CONF,ADC Display 0 Configuration Register"
|
|
bitfld.long 0x14 15. " MCU_DISP0_DATA_MAP ,Data mapping rule used when the MCU accesses the display 0 select" "Data,Command"
|
|
bitfld.long 0x14 14. " MCU_DISP0_DATA_WIDTH ,Generic data word width for display 0 access by the MCU" "16 bits,24 bits"
|
|
textline " "
|
|
bitfld.long 0x14 12.--13. " DISP0_TYPE ,Display 0 addressing format" "Full,Full/byte,XY,?..."
|
|
hexmask.long.word 0x14 0.--11. 1. " DISP0_SL ,Display 0 stride line length minus 1"
|
|
line.long 0x18 "ADC_DISP0_RD_AP,ADC Display 0 Read Acknowledge Pattern Register"
|
|
bitfld.long 0x18 24. " DISP0_ACK_MAP ,Select data mapping rule for the acknowledge word" "Data,Command"
|
|
hexmask.long.tbyte 0x18 0.--23. 1. " DISP0_ACK_PTRN ,Display 0 acknowledge pattern"
|
|
line.long 0x1c "ADC_DISP0_RDM,ADC Display 0 Read Mask Register"
|
|
bitfld.long 0x1c 23. " DISP0_MASK_ACK_DATA ,Display 0 read data mask bit 23" "0,1"
|
|
bitfld.long 0x1c 22. ",Display 0 read data mask bit 22" "0,1"
|
|
bitfld.long 0x1c 21. ",Display 0 read data mask bit 21" "0,1"
|
|
bitfld.long 0x1c 20. ",Display 0 read data mask bit 20" "0,1"
|
|
bitfld.long 0x1c 19. ",Display 0 read data mask bit 19" "0,1"
|
|
bitfld.long 0x1c 18. ",Display 0 read data mask bit 18" "0,1"
|
|
bitfld.long 0x1c 17. ",Display 0 read data mask bit 17" "0,1"
|
|
bitfld.long 0x1c 16. ",Display 0 read data mask bit 16" "0,1"
|
|
bitfld.long 0x1c 15. ",Display 0 read data mask bit 15" "0,1"
|
|
bitfld.long 0x1c 14. ",Display 0 read data mask bit 14" "0,1"
|
|
bitfld.long 0x1c 13. ",Display 0 read data mask bit 13" "0,1"
|
|
bitfld.long 0x1c 12. ",Display 0 read data mask bit 12" "0,1"
|
|
bitfld.long 0x1c 11. ",Display 0 read data mask bit 11" "0,1"
|
|
bitfld.long 0x1c 10. ",Display 0 read data mask bit 10" "0,1"
|
|
bitfld.long 0x1c 9. ",Display 0 read data mask bit 9" "0,1"
|
|
bitfld.long 0x1c 8. ",Display 0 read data mask bit 8" "0,1"
|
|
bitfld.long 0x1c 7. ",Display 0 read data mask bit 7" "0,1"
|
|
bitfld.long 0x1c 6. ",Display 0 read data mask bit 6" "0,1"
|
|
bitfld.long 0x1c 5. ",Display 0 read data mask bit 5" "0,1"
|
|
bitfld.long 0x1c 4. ",Display 0 read data mask bit 4" "0,1"
|
|
bitfld.long 0x1c 3. ",Display 0 read data mask bit 3" "0,1"
|
|
bitfld.long 0x1c 2. ",Display 0 read data mask bit 2" "0,1"
|
|
bitfld.long 0x1c 1. ",Display 0 read data mask bit 1" "0,1"
|
|
bitfld.long 0x1c 0. ",Display 0 read data mask bit 0" "0,1"
|
|
line.long 0x20 "ADC_DISP0_SS,ADC Display 0 Screen Size Register"
|
|
hexmask.long.word 0x20 16.--25. 1. " SCREEN0_HEIGHT ,Display 0 screen height minus 1"
|
|
hexmask.long.word 0x20 0.--9. 1. " SCREEN0_WIDTH ,Display 0 screen width minus 1"
|
|
line.long 0x24 "ADC_DISP1_CONF,ADC Display 1 Configuration Register"
|
|
bitfld.long 0x24 15. " MCU_DISP1_DATA_MAP ,Select data mapping rule used when the MCU accesses the display 1" "Data,Command"
|
|
bitfld.long 0x24 14. " MCU_DISP1_DATA_WIDTH ,Data word width for display 1 access by the MCU" "16 bits,24 bits"
|
|
textline " "
|
|
bitfld.long 0x24 12.--13. " DISP1_TYPE ,Display 1 addressing format" "Full,Full/byte,XY,?..."
|
|
hexmask.long.word 0x24 0.--11. 1. " DISP1_SL ,Display 1 stride line length minus 1"
|
|
line.long 0x28 "ADC_DISP1_RD_AP,ADC Display 1 Read Acknowledge Pattern Register"
|
|
bitfld.long 0x28 24. " DISP1_ACK_MAP ,Select data mapping rule for the acknowledge word" "Data,Command"
|
|
hexmask.long.tbyte 0x28 0.--23. 1. " DISP1_ACK_PTRN ,Display 1 acknowledge pattern"
|
|
line.long 0x2c "ADC_DISP1_RDM,ADC Display 1 Read Mask Register"
|
|
bitfld.long 0x2c 23. " DISP1_MASK_ACK_DATA ,Display 1 read data mask bit 23" "0,1"
|
|
bitfld.long 0x2c 22. ",Display 1 read data mask bit 22" "0,1"
|
|
bitfld.long 0x2c 21. ",Display 1 read data mask bit 21" "0,1"
|
|
bitfld.long 0x2c 20. ",Display 1 read data mask bit 20" "0,1"
|
|
bitfld.long 0x2c 19. ",Display 1 read data mask bit 19" "0,1"
|
|
bitfld.long 0x2c 18. ",Display 1 read data mask bit 18" "0,1"
|
|
bitfld.long 0x2c 17. ",Display 1 read data mask bit 17" "0,1"
|
|
bitfld.long 0x2c 16. ",Display 1 read data mask bit 16" "0,1"
|
|
bitfld.long 0x2c 15. ",Display 1 read data mask bit 15" "0,1"
|
|
bitfld.long 0x2c 14. ",Display 1 read data mask bit 14" "0,1"
|
|
bitfld.long 0x2c 13. ",Display 1 read data mask bit 13" "0,1"
|
|
bitfld.long 0x2c 12. ",Display 1 read data mask bit 12" "0,1"
|
|
bitfld.long 0x2c 11. ",Display 1 read data mask bit 11" "0,1"
|
|
bitfld.long 0x2c 10. ",Display 1 read data mask bit 10" "0,1"
|
|
bitfld.long 0x2c 9. ",Display 1 read data mask bit 9" "0,1"
|
|
bitfld.long 0x2c 8. ",Display 1 read data mask bit 8" "0,1"
|
|
bitfld.long 0x2c 7. ",Display 1 read data mask bit 7" "0,1"
|
|
bitfld.long 0x2c 6. ",Display 1 read data mask bit 6" "0,1"
|
|
bitfld.long 0x2c 5. ",Display 1 read data mask bit 5" "0,1"
|
|
bitfld.long 0x2c 4. ",Display 1 read data mask bit 4" "0,1"
|
|
bitfld.long 0x2c 3. ",Display 1 read data mask bit 3" "0,1"
|
|
bitfld.long 0x2c 2. ",Display 1 read data mask bit 2" "0,1"
|
|
bitfld.long 0x2c 1. ",Display 1 read data mask bit 1" "0,1"
|
|
bitfld.long 0x2c 0. ",Display 1 read data mask bit 0" "0,1"
|
|
line.long 0x30 "ADC_DISP12_SS,ADC Displays 1 or 2 Screen Size Register"
|
|
hexmask.long.word 0x30 16.--25. 1. " SCREEN12_HEIGHT ,Display 1 or 2 screen height minus 1"
|
|
hexmask.long.word 0x30 0.--9. 1. " SCREEN12_WIDTH ,Display 1 or 2 screen width minus 1"
|
|
line.long 0x34 "ADC_DISP2_CONF,ADC Display 2 Configuration Register"
|
|
bitfld.long 0x34 15. " MCU_DISP2_DATA_MAP ,Data mapping rule used when the MCU accesses the display 2 select" "Data,Command"
|
|
bitfld.long 0x34 14. " MCU_DISP2_DATA_WIDTH ,Data word width for display 2 access by the MCU" "16 bits,24 bits"
|
|
textline " "
|
|
bitfld.long 0x34 12.--13. " DISP2_TYPE ,Display 2 addressing format" "Full,Full/byte,XY,?..."
|
|
hexmask.long.word 0x34 0.--11. 1. " DISP2_SL ,Display 2 stride line length minus 1"
|
|
line.long 0x38 "ADC_DISP2_RD_AP,ADC Display 2 Read Acknowledge Pattern Register"
|
|
bitfld.long 0x38 24. " DISP2_ACK_MAP ,Data mapping rule for the acknowledge word select" "Data,Command"
|
|
hexmask.long.tbyte 0x38 0.--23. 1. " DISP2_ACK_PTRN ,Display 2 acknowledge pattern"
|
|
line.long 0x3c "ADC_DISP2_RDM,ADC Display 2 Read Mask Register"
|
|
bitfld.long 0x3c 23. " DISP2_MASK_ACK_DATA ,Display 2 read data mask bit 23" "0,1"
|
|
bitfld.long 0x3c 22. ",Display 2 read data mask bit 22" "0,1"
|
|
bitfld.long 0x3c 21. ",Display 2 read data mask bit 21" "0,1"
|
|
bitfld.long 0x3c 20. ",Display 2 read data mask bit 20" "0,1"
|
|
bitfld.long 0x3c 19. ",Display 2 read data mask bit 19" "0,1"
|
|
bitfld.long 0x3c 18. ",Display 2 read data mask bit 18" "0,1"
|
|
bitfld.long 0x3c 17. ",Display 2 read data mask bit 17" "0,1"
|
|
bitfld.long 0x3c 16. ",Display 2 read data mask bit 16" "0,1"
|
|
bitfld.long 0x3c 15. ",Display 2 read data mask bit 15" "0,1"
|
|
bitfld.long 0x3c 14. ",Display 2 read data mask bit 14" "0,1"
|
|
bitfld.long 0x3c 13. ",Display 2 read data mask bit 13" "0,1"
|
|
bitfld.long 0x3c 12. ",Display 2 read data mask bit 12" "0,1"
|
|
bitfld.long 0x3c 11. ",Display 2 read data mask bit 11" "0,1"
|
|
bitfld.long 0x3c 10. ",Display 2 read data mask bit 10" "0,1"
|
|
bitfld.long 0x3c 9. ",Display 2 read data mask bit 9" "0,1"
|
|
bitfld.long 0x3c 8. ",Display 2 read data mask bit 8" "0,1"
|
|
bitfld.long 0x3c 7. ",Display 2 read data mask bit 7" "0,1"
|
|
bitfld.long 0x3c 6. ",Display 2 read data mask bit 6" "0,1"
|
|
bitfld.long 0x3c 5. ",Display 2 read data mask bit 5" "0,1"
|
|
bitfld.long 0x3c 4. ",Display 2 read data mask bit 4" "0,1"
|
|
bitfld.long 0x3c 3. ",Display 2 read data mask bit 3" "0,1"
|
|
bitfld.long 0x3c 2. ",Display 2 read data mask bit 2" "0,1"
|
|
bitfld.long 0x3c 1. ",Display 2 read data mask bit 1" "0,1"
|
|
bitfld.long 0x3c 0. ",Display 2 read data mask bit 0" "0,1"
|
|
line.long 0x40 "ADC_DISP_VSYNC,ADC Displays Vertical Synchronization Register"
|
|
bitfld.long 0x40 30. " DISP12_VSYNC_WIDTH_L ,Resolution of DISP0_VSYNC_WIDTH for the displays 1 or 2" "Pixels,Lines"
|
|
hexmask.long.byte 0x40 24.--29. 1. " DISP12_VSYNC_WIDTH ,VSYNC pulse width minus 1 of the displays 1 or 2"
|
|
textline " "
|
|
bitfld.long 0x40 22. " DISP0_VSYNC_WIDTH_L ,Resolution of DISP0_VSYNC_WIDTH for the display 0" "Pixels,Lines"
|
|
hexmask.long.byte 0x40 16.--21. 1. " DISP0_VSYNC_WIDTH ,VSYNC pulse width minus 1 of the display 0"
|
|
textline " "
|
|
hexmask.long.word 0x40 6.--15. 1. " DISP_LN_WT ,Delay between the start point of the first sensor row and the VSYNC pulse"
|
|
bitfld.long 0x40 4. " DISP12_VSYNC_SEL ,Selection of the displays 1 or 2 to be in vertical synchronization mode" "Display 1,Display 2"
|
|
textline " "
|
|
bitfld.long 0x40 2.--3. " DISP12_VSYNC_MODE ,Displays 1 or 2 vertical synchronization mode" "Disabled,Internal,Internal/synchronized,External"
|
|
textline " "
|
|
bitfld.long 0x40 0.--1. " DISPL0_VSYNC_MODE ,Display 0 vertical synchronization mode" "Disabled,Internal,Internal/synchronized,External"
|
|
tree.end
|
|
width 0x16
|
|
tree "DI Registers"
|
|
width 19.
|
|
group.long 0x124++0x3B
|
|
line.long 0x00 "DI_DISP_IF_CONF,DI Display Interface Configuration Register"
|
|
bitfld.long 0x00 27.--30. " DISP012_DEAD_CLK_NUM ,Number of dead clock cycles" "4 cycles,5 cycles,6 cycles,7 cycles,8 cycles,9 cycles,10 cycles,11 cycles,12 cycles,13 cycles,14 cycles,15 cycles,16 cycles,17 cycles,18 cycles,19 cycles"
|
|
bitfld.long 0x00 26. " DISP3_CLK_IDLE ,Display 3 interface clock idle enable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 25. " DISP3_CLK_SEL ,Select display 3 interface clock" "Enabled,Disabled"
|
|
bitfld.long 0x00 24. " DISP3_DATAMSK ,Data mask for the display 3" "Not masked,Masked"
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " DISP2_PAR_BURST_MODE ,Display 2 parallel interface burst mode" "CS|R/W|ENABLE,BCLK,Single,?..."
|
|
bitfld.long 0x00 17.--19. " DISP2_IF_MODE ,Display 2 interface mode" "80|CS,80|R/W,68k|CS,68k|ENABLE,3-wire,4-wire,5-wire|serial,5-wire|CS"
|
|
textline " "
|
|
bitfld.long 0x00 16. " DISP2_EN ,Display 2 enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 12.--13. " DISP1_PAR_BURST_MODE ,Display 1 parallel interface burst mode" "CS|R/W|ENABLE,BCLK,Single,?..."
|
|
textline " "
|
|
bitfld.long 0x00 9.--11. " DISP1_IF_MODE ,Display 1 interface mode" "80|CS,80|R/W,68k|CS,68k|ENABLE,3-wire,4-wire,5-wire|serial,5-wire|CS"
|
|
bitfld.long 0x00 8. " DISP1_EN ,Display 1 enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3.--4. " DISP0_PAR_BURST_MODE ,Display 0 parallel interface burst mode" "CS|R/W|ENABLE,BCLK,Single,?..."
|
|
bitfld.long 0x00 1.--2. " DISP0_IF_MODE ,Display 0 interface mode" "80|CS,80|R/W,68k|CS,68k|ENABLE"
|
|
textline " "
|
|
bitfld.long 0x00 0. " DISP0_EN ,Display 0 enable" "Disabled,Enabled"
|
|
line.long 0x04 "DI_DISP_SIG_POL,DI Display Signals Polarity Register"
|
|
bitfld.long 0x04 31. " D2_BCLK_POL ,Display parallel interface burst clock polarity for the display 2" "Straight,Inverse"
|
|
bitfld.long 0x04 30. " D1_BCLK_POL ,Display parallel interface burst clock polarity for the display 1" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 29. " D0_BCLK_POL ,Display parallel interface burst clock polarity for the display 0" "Straight,Inverse"
|
|
bitfld.long 0x04 28. " D3_VSYNC_POL ,Vertical synchronization signal polarity for the display 3" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 27. " D3_HSYNC_POL ,Horizontal synchronization signal polarity for the display 3" "Low,High"
|
|
bitfld.long 0x04 26. " D3_DRDY_SHARP_POL ,Output enable polarity or Sharp signals polarity for display 3" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 25. " D3_CLK_POL ,Display interface clock polarity for the display 3" "Straight,Inverse"
|
|
bitfld.long 0x04 24. " D3_DATA_POL ,Data polarity for the display 3" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 23. " D2_SER_RS_POL ,Address bit polarity for the display 2 serial interface" "Straight,Inverse"
|
|
bitfld.long 0x04 22. " D2_SD_CLK_POL ,Serial interface clock polarity for the display 2" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 21. " D2_SD_D_POL ,Serial data polarity for the display 2" "Straight,Inverse"
|
|
bitfld.long 0x04 20. " D2_RD_POL ,Write signal polarity for the display 2" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 19. " D2_WR_POL ,Write signal polarity for the display 2" "Low,High"
|
|
bitfld.long 0x04 18. " D2_PAR_RS_POL ,Address bit polarity for the display 2 parallel interface" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 17. " D2_CS_POL ,Chip select signal polarity for the display 2" "Low,High"
|
|
bitfld.long 0x04 16. " D2_DATA_POL ,Data polarity for the display 2" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 15. " D1_SER_RS_POL ,Address bit polarity for the display 1 serial interface" "Straight,Inverse"
|
|
bitfld.long 0x04 14. " D1_SD_CLK_POL ,Serial interface clock polarity for the display 1" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 13. " D1_SD_D_POL ,Serial data polarity for the display 1" "Straight,Inverse"
|
|
bitfld.long 0x04 12. " D1_RD_POL ,Write signal polarity for the display 1" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 11. " D1_WR_POL ,Write signal polarity for the display 1" "Low,High"
|
|
bitfld.long 0x04 10. " D1_PAR_RS_POL ,Address bit polarity for the display 1 parallel interface" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 9. " D1_CS_POL ,Chip select signal polarity for the display 1" "Low,High"
|
|
bitfld.long 0x04 8. " D1_DATA_POL ,Data polarity for the display 1" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x04 6. " D12_VSYNC_POL ,Vertical synchronization signal polarity for the displays 1 and 2" "Low,High"
|
|
bitfld.long 0x04 5. " D0_VSYNC_POL ,Vertical synchronization signal polarity for the display 0" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 4. " D0_RD_POL ,Write signal polarity for the display 0" "Low,High"
|
|
bitfld.long 0x04 3. " D0_WR_POL ,Write signal polarity for the display 0" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 2. " D0_PAR_RS_POL ,Address bit polarity for the display 0 parallel interface" "Straight,Inverse"
|
|
bitfld.long 0x04 1. " D0_CS_POL ,Chip select signal polarity for the display 0" "Low,High"
|
|
textline " "
|
|
bitfld.long 0x04 0. " D0_DATA_POL ,Data polarity for the display 0" "Straight,Inverse"
|
|
line.long 0x08 "DI_SER_DISP1_CONF,DI Serial Display 1 Configuration Register"
|
|
bitfld.long 0x08 24. " DISP1_SER_BURST_MODE ,Burst mode enable" "Single,Burst"
|
|
bitfld.long 0x08 16.--20. " DISP1_SER_BIT_NUM ,Output/input data bit number minus 1" "1 bit,2 bits,3 bits,4 bits,5 bits,6 bits,7 bits,8 bits,9 bits,10 bits,11 bits,12 bits,13 bits,14 bits,15 bits,16 bits,17 bits,18 bits,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x08 8.--15. 1. " DISP1_PREAMBLE ,Preamble contents"
|
|
bitfld.long 0x08 4.--6. " DISP1_PREAMBLE_LENGTH ,Preamble length minus 1 in bits" "1 bit,2 bits,3 bits,4 bits,5 bits,6 bits,7 bits,8 bits"
|
|
textline " "
|
|
bitfld.long 0x08 1.--2. " DISP1_RW_CONFIG ,Configuration of read/write (RW) control bit to be sent via serial interface" "No RW,Before RS,After RS,?..."
|
|
bitfld.long 0x08 0. " DISP1_PREAMBLE_EN ,Preamble enable" "Disabled,Enabled"
|
|
line.long 0x0c "DI_SER_DISP2_CONF,DI Serial Display 2 Configuration Register"
|
|
bitfld.long 0x0c 24. " DISP2_SER_BURST_MODE ,Burst mode enable" "Single,Burst"
|
|
bitfld.long 0x0c 16.--20. " DISP2_SER_BIT_NUM ,Output/input data bit number minus 1" "1 bit,2 bits,3 bits,4 bits,5 bits,6 bits,7 bits,8 bits,9 bits,10 bits,11 bits,12 bits,13 bits,14 bits,15 bits,16 bits,17 bits,18 bits,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x0c 8.--15. 1. " DISP2_PREAMBLE ,Preamble contents"
|
|
bitfld.long 0x0c 4.--6. " DISP2_PREAMBLE_LENGTH ,Preamble length minus 1 in bits" "1 bit,2 bits,3 bits,4 bits,5 bits,6 bits,7 bits,8 bits"
|
|
textline " "
|
|
bitfld.long 0x0c 1.--2. " DISP2_RW_CONFIG ,Configuration of read/write (RW) control bit to be sent via serial interface" "No RW,Before RS,After RS,?..."
|
|
bitfld.long 0x0c 0. " DISP2_PREAMBLE_EN ,Preamble enable" "Disabled,Enabled"
|
|
line.long 0x10 "DI_HSP_CLK_PER,DI HSP_CLK Period Register"
|
|
hexmask.long.byte 0x10 16.--22. 1. " HSP_CLK_PERIOD_2 ,HSP_CLK period option 2"
|
|
hexmask.long.byte 0x10 0.--6. 1. " HSP_CLK_PERIOD_1 ,HSP_CLK period option 1"
|
|
width 21.
|
|
line.long 0x14 "DI_DISP0_TIME_CONF_1,DI Display 0 Time Configuration Register 1"
|
|
hexmask.long.word 0x14 22.--31. 1. " DISP0_IF_CLK_DOWN_WR ,Display 0 interface clock falling edge position for display write access"
|
|
hexmask.long.word 0x14 12.--21. 1. " DISP0_IF_CLK_UP_WR[9:0] ,Display 0 interface clock rising edge position for display write access"
|
|
textline " "
|
|
hexmask.long.word 0x14 0.--11. 1. " DISP0_IF_CLK_PER_WR ,Display 0 interface clock period for display write access"
|
|
line.long 0x18 "DI_DISP0_TIME_CONF_2,DI Display 0 Time Configuration Register 2"
|
|
hexmask.long.word 0x18 22.--31. 1. " DISP0_IF_CLK_DOWN_RD ,Display 0 interface clock falling edge position for display read access"
|
|
hexmask.long.word 0x18 12.--21. 1. " DISP0_IF_CLK_UP_RD[9:0] ,Display 0 interface clock rising edge position for display read access"
|
|
textline " "
|
|
hexmask.long.word 0x18 0.--11. 1. " DISP0_IF_CLK_PER_RD ,Display 0 interface clock period for display read access"
|
|
line.long 0x1c "DI_DISP0_TIME_CONF_3,DI Display 0 Time Configuration Register 3"
|
|
bitfld.long 0x1c 28.--29. " DISP0_RD_WAIT_ST ,Number of wait states required to read data from the display" "No states,1 state,2 states,3 states"
|
|
hexmask.long.word 0x1c 16.--25. 1. " DISP0_READ_EN ,Display 0 read point position"
|
|
textline " "
|
|
hexmask.long.word 0x1c 0.--11. 1. " DISP0_PIX_CLK_PER ,Display 0 pixel clock period"
|
|
line.long 0x20 "DI_DISP1_TIME_CONF_1,DI Display 1 Time Configuration Register 1"
|
|
hexmask.long.word 0x20 22.--31. 1. " DISP1_IF_CLK_DOWN_WR ,Display 1 interface clock falling edge position for display write access"
|
|
hexmask.long.word 0x20 12.--21. 1. " DISP1_IF_CLK_UP_WR[9:0] ,Display 1 interface clock rising edge position for display write access"
|
|
textline " "
|
|
hexmask.long.word 0x20 0.--11. 1. " DISP1_IF_CLK_PER_WR ,Display 1 interface clock period for display write access"
|
|
line.long 0x24 "DI_DISP1_TIME_CONF_2,DI Display 1 Time Configuration Register 2"
|
|
hexmask.long.word 0x24 22.--31. 1. " DISP1_IF_CLK_DOWN_RD ,Display 1 interface clock falling edge position for display read access"
|
|
hexmask.long.word 0x24 12.--21. 1. " DISP1_IF_CLK_UP_RD[9:0] ,Display 1 interface clock rising edge position for display read access"
|
|
textline " "
|
|
hexmask.long.word 0x24 0.--11. 1. " DISP1_IF_CLK_PER_RD ,Display 1 interface clock period for display read access"
|
|
line.long 0x28 "DI_DISP1_TIME_CONF_3,DI Display 1 Time Configuration Register 3"
|
|
bitfld.long 0x28 28.--29. " DISP1_RD_WAIT_ST ,Number of wait states required to read data from the display" "No states,1 state,2 states,3 states"
|
|
hexmask.long.word 0x28 16.--25. 1. " DISP1_READ_EN ,Display 1 read point position"
|
|
textline " "
|
|
hexmask.long.word 0x28 0.--11. 1. " DISP12_PIX_CLK_PER ,Display 1 and 2 pixel clock period"
|
|
line.long 0x2c "DI_DISP2_TIME_CONF_1,DI Display 2 Time Configuration Register 1"
|
|
hexmask.long.word 0x2c 22.--31. 1. " DISP2_IF_CLK_DOWN_WR ,Display 2 interface clock falling edge position for display write access"
|
|
hexmask.long.word 0x2c 12.--21. 1. " DISP2_IF_CLK_UP_WR[9:0] ,Display 2 interface clock rising edge position for display write access"
|
|
textline " "
|
|
hexmask.long.word 0x2c 0.--11. 1. " DISP2_IF_CLK_PER_WR ,Display 2 interface clock period for display write access"
|
|
line.long 0x30 "DI_DISP2_TIME_CONF_2,DI Display 2 Time Configuration Register 2"
|
|
hexmask.long.word 0x30 22.--31. 1. " DISP2_IF_CLK_DOWN_RD ,Display 2 interface clock falling edge position for display read access"
|
|
hexmask.long.word 0x30 12.--21. 1. " DISP2_IF_CLK_UP_RD[9:0] ,Display 2 interface clock rising edge position for display read access"
|
|
textline " "
|
|
hexmask.long.word 0x30 0.--11. 1. " DISP2_IF_CLK_PER_RD ,Display 2 interface clock period for display read access"
|
|
line.long 0x34 "DI_DISP2_TIME_CONF_3,DI Display 2 Time Configuration Register 3"
|
|
bitfld.long 0x34 28.--29. " DISP2_RD_WAIT_ST ,Number of wait states required to read data from the display" "No states,1 state,2 states,3 states"
|
|
hexmask.long.word 0x34 16.--25. 1. " DISP2_READ_EN ,Display 2 read point position"
|
|
line.long 0x38 "DI_DISP3_TIME_CONF,DI Display 3 Time Configuration Register"
|
|
hexmask.long.word 0x38 22.--31. 1. " DISP3_IF_CLK_DOWN_WR ,Display 3 interface clock falling edge position for display write access"
|
|
hexmask.long.word 0x38 12.--21. 1. " DISP3_IF_CLK_UP_WR[9:0] ,Display 3 interface clock rising edge position for display write access"
|
|
textline " "
|
|
hexmask.long.word 0x38 0.--11. 1. " DISP3_IF_CLK_PER_WR ,Display 3 interface clock period for display write access"
|
|
width 18.
|
|
tree "DI Display 0 Byte Mapping Registers"
|
|
group.long 0x160++0x17
|
|
line.long 0x0 "DI_DISP0_DB0_MAP,DI Display 0 Data Byte 0 Mapping Register"
|
|
bitfld.long 0x0 26.--30. " MD00_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 21.--25. " MD00_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x0 16.--20. " MD00_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 14.--15. " MD00_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 12.--13. " MD00_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 10.--11. " MD00_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " MD00_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 6.--7. " MD00_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 4.--5. " MD00_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 2.--3. " MD00_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " MD00_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x4 "DI_DISP0_DB1_MAP,DI Display 0 Data Byte 1 Mapping Register"
|
|
bitfld.long 0x4 26.--30. " MD01_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 21.--25. " MD01_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x4 16.--20. " MD01_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 14.--15. " MD01_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 12.--13. " MD01_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 10.--11. " MD01_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 8.--9. " MD01_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 6.--7. " MD01_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 4.--5. " MD01_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 2.--3. " MD01_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 0.--1. " MD01_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x8 "DI_DISP0_DB2_MAP,DI Display 0 Data Byte 2 Mapping Register"
|
|
bitfld.long 0x8 26.--30. " MD02_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 21.--25. " MD02_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x8 16.--20. " MD02_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 14.--15. " MD02_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 12.--13. " MD02_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 10.--11. " MD02_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 8.--9. " MD02_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 6.--7. " MD02_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 4.--5. " MD02_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 2.--3. " MD02_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 0.--1. " MD02_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0xC "DI_DISP0_CB0_MAP,DI Display 0 Command Byte 0 Mapping Register"
|
|
bitfld.long 0xC 26.--30. " MC00_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 21.--25. " MC00_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0xC 16.--20. " MC00_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 14.--15. " MC00_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 12.--13. " MC00_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 10.--11. " MC00_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 8.--9. " MC00_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 6.--7. " MC00_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 4.--5. " MC00_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 2.--3. " MC00_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 0.--1. " MC00_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x10 "DI_DISP0_CB1_MAP,DI Display 0 Command Byte 1 Mapping Register"
|
|
bitfld.long 0x10 26.--30. " MC01_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 21.--25. " MC01_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x10 16.--20. " MC01_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 14.--15. " MC01_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 12.--13. " MC01_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 10.--11. " MC01_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 8.--9. " MC01_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 6.--7. " MC01_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 4.--5. " MC01_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 2.--3. " MC01_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 0.--1. " MC01_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x14 "DI_DISP0_CB2_MAP,DI Display 0 Command Byte 2 Mapping Register"
|
|
bitfld.long 0x14 26.--30. " MC02_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 21.--25. " MC02_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x14 16.--20. " MC02_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 14.--15. " MC02_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 12.--13. " MC02_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 10.--11. " MC02_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 8.--9. " MC02_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 6.--7. " MC02_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 4.--5. " MC02_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 2.--3. " MC02_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 0.--1. " MC02_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
tree.end
|
|
tree "DI Display 1 Byte Mapping Registers"
|
|
group.long 0x178++0x17
|
|
line.long 0x0 "DI_DISP1_DB0_MAP,DI Display 1 Data Byte 0 Mapping Register"
|
|
bitfld.long 0x0 26.--30. " MD10_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 21.--25. " MD10_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x0 16.--20. " MD10_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 14.--15. " MD10_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 12.--13. " MD10_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 10.--11. " MD10_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " MD10_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 6.--7. " MD10_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 4.--5. " MD10_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 2.--3. " MD10_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " MD10_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x4 "DI_DISP1_DB1_MAP,DI Display 1 Data Byte 1 Mapping Register"
|
|
bitfld.long 0x4 26.--30. " MD11_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 21.--25. " MD11_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x4 16.--20. " MD11_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 14.--15. " MD11_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 12.--13. " MD11_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 10.--11. " MD11_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 8.--9. " MD11_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 6.--7. " MD11_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 4.--5. " MD11_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 2.--3. " MD11_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 0.--1. " MD11_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x8 "DI_DISP1_DB2_MAP,DI Display 1 Data Byte 2 Mapping Register"
|
|
bitfld.long 0x8 26.--30. " MD12_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 21.--25. " MD12_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x8 16.--20. " MD12_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 14.--15. " MD12_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 12.--13. " MD12_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 10.--11. " MD12_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 8.--9. " MD12_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 6.--7. " MD12_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 4.--5. " MD12_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 2.--3. " MD12_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 0.--1. " MD12_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0xC "DI_DISP1_CB0_MAP,DI Display 1 Command Byte 0 Mapping Register"
|
|
bitfld.long 0xC 26.--30. " MC10_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 21.--25. " MC10_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0xC 16.--20. " MC10_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 14.--15. " MC10_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 12.--13. " MC10_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 10.--11. " MC10_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 8.--9. " MC10_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 6.--7. " MC10_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 4.--5. " MC10_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 2.--3. " MC10_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 0.--1. " MC10_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x10 "DI_DISP1_CB1_MAP,DI Display 1 Command Byte 1 Mapping Register"
|
|
bitfld.long 0x10 26.--30. " MC11_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 21.--25. " MC11_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x10 16.--20. " MC11_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 14.--15. " MC11_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 12.--13. " MC11_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 10.--11. " MC11_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 8.--9. " MC11_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 6.--7. " MC11_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 4.--5. " MC11_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 2.--3. " MC11_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 0.--1. " MC11_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x14 "DI_DISP1_CB2_MAP,DI Display 1 Command Byte 2 Mapping Register"
|
|
bitfld.long 0x14 26.--30. " MC12_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 21.--25. " MC12_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x14 16.--20. " MC12_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 14.--15. " MC12_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 12.--13. " MC12_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 10.--11. " MC12_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 8.--9. " MC12_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 6.--7. " MC12_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 4.--5. " MC12_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 2.--3. " MC12_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 0.--1. " MC12_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
tree.end
|
|
tree "DI Display 2 Byte Mapping Registers"
|
|
group.long 0x190++0x17
|
|
line.long 0x0 "DI_DISP2_DB0_MAP,DI Display 2 Data Byte 0 Mapping Register"
|
|
bitfld.long 0x0 26.--30. " MD20_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 21.--25. " MD20_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x0 16.--20. " MD20_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 14.--15. " MD20_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 12.--13. " MD20_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 10.--11. " MD20_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " MD20_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 6.--7. " MD20_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 4.--5. " MD20_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 2.--3. " MD20_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " MD20_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x4 "DI_DISP2_DB1_MAP,DI Display 2 Data Byte 1 Mapping Register"
|
|
bitfld.long 0x4 26.--30. " MD21_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 21.--25. " MD21_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x4 16.--20. " MD21_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 14.--15. " MD21_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 12.--13. " MD21_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 10.--11. " MD21_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 8.--9. " MD21_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 6.--7. " MD21_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 4.--5. " MD21_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 2.--3. " MD21_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 0.--1. " MD21_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x8 "DI_DISP2_DB2_MAP,DI Display 2 Data Byte 2 Mapping Register"
|
|
bitfld.long 0x8 26.--30. " MD22_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 21.--25. " MD22_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x8 16.--20. " MD22_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 14.--15. " MD22_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 12.--13. " MD22_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 10.--11. " MD22_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 8.--9. " MD22_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 6.--7. " MD22_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 4.--5. " MD22_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 2.--3. " MD22_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 0.--1. " MD22_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0xC "DI_DISP2_CB0_MAP,DI Display 2 Command Byte 0 Mapping Register"
|
|
bitfld.long 0xC 26.--30. " MC20_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 21.--25. " MC20_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0xC 16.--20. " MC20_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0xC 14.--15. " MC20_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 12.--13. " MC20_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 10.--11. " MC20_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 8.--9. " MC20_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 6.--7. " MC20_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 4.--5. " MC20_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0xC 2.--3. " MC20_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0xC 0.--1. " MC20_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x10 "DI_DISP2_CB1_MAP,DI Display 2 Command Byte 1 Mapping Register"
|
|
bitfld.long 0x10 26.--30. " MC21_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 21.--25. " MC21_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x10 16.--20. " MC21_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x10 14.--15. " MC21_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 12.--13. " MC21_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 10.--11. " MC21_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 8.--9. " MC21_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 6.--7. " MC21_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 4.--5. " MC21_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x10 2.--3. " MC21_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x10 0.--1. " MC21_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x14 "DI_DISP2_CB2_MAP,DI Display 2 Command Byte 2 Mapping Register"
|
|
bitfld.long 0x14 26.--30. " MC22_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 21.--25. " MC22_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x14 16.--20. " MC22_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x14 14.--15. " MC22_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 12.--13. " MC22_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 10.--11. " MC22_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 8.--9. " MC22_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 6.--7. " MC22_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 4.--5. " MC22_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x14 2.--3. " MC22_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x14 0.--1. " MC22_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
tree.end
|
|
tree "DI Display 3 Byte Mapping Registers"
|
|
group.long 0x1A8++0xB
|
|
line.long 0x0 "DI_DISP3_B0_MAP,DI Display 3 Data Byte 0 Mapping Register"
|
|
bitfld.long 0x0 26.--30. " M30_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 21.--25. " M30_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x0 16.--20. " M30_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x0 14.--15. " M30_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 12.--13. " M30_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 10.--11. " M30_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " M30_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 6.--7. " M30_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 4.--5. " M30_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x0 2.--3. " M30_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " M30_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x4 "DI_DISP3_B1_MAP,DI Display 3 Data Byte 1 Mapping Register"
|
|
bitfld.long 0x4 26.--30. " M31_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 21.--25. " M31_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x4 16.--20. " M31_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x4 14.--15. " M31_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 12.--13. " M31_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 10.--11. " M31_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 8.--9. " M31_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 6.--7. " M31_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 4.--5. " M31_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x4 2.--3. " M31_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x4 0.--1. " M31_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
line.long 0x8 "DI_DISP3_B2_MAP,DI Display 3 Data Byte 2 Mapping Register"
|
|
bitfld.long 0x8 26.--30. " M32_OFFS2 ,Offset in third clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 21.--25. " M32_OFFS1 ,Offset in second clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
textline " "
|
|
bitfld.long 0x8 16.--20. " M32_OFFS0 ,Offset in first clock cycle" "0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,1F"
|
|
bitfld.long 0x8 14.--15. " M32_M7 ,Mask for bit 7" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 12.--13. " M32_M6 ,Mask for bit 6" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 10.--11. " M32_M5 ,Mask for bit 5" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 8.--9. " M32_M4 ,Mask for bit 4" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 6.--7. " M32_M3 ,Mask for bit 3" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 4.--5. " M32_M2 ,Mask for bit 2" "First,Second,Third,Masked"
|
|
bitfld.long 0x8 2.--3. " M32_M1 ,Mask for bit 1" "First,Second,Third,Masked"
|
|
textline " "
|
|
bitfld.long 0x8 0.--1. " M32_M0 ,Mask for bit 0" "First,Second,Third,Masked"
|
|
tree.end
|
|
tree "DI Display Access Registers"
|
|
group.long 0x1B4++0x7
|
|
line.long 0x0 "DI_DISP_ACC_CC,DI Display Access Cycles Count Register"
|
|
bitfld.long 0x0 12.--13. " DISP3_IF_CLK_CNT_D ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
bitfld.long 0x0 10.--11. " DISP2_IF_CLK_CNT_C ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
textline " "
|
|
bitfld.long 0x0 8.--9. " DISP2_IF_CLK_CNT_D ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
bitfld.long 0x0 6.--7. " DISP1_IF_CLK_CNT_C ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
textline " "
|
|
bitfld.long 0x0 4.--5. " DISP1_IF_CLK_CNT_D ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
bitfld.long 0x0 2.--3. " DISP0_IF_CLK_CNT_C ,Output one command word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " DISP0_IF_CLK_CNT_D ,Output/input one data word display clock cycles number minus 1" "1 cycle,2 cycles,3 cycles,4 cycles"
|
|
line.long 0x4 "DI_DISP_LLA_CONF,DI Display Low Level Access Configuration Register"
|
|
bitfld.long 0x4 5. " DRCT_BE_MODE ,Display MCU low level access set byte enable mode" "Not set,Set"
|
|
bitfld.long 0x4 4. " DRCT_MAP_DC ,Display mapping select" "Data,Command"
|
|
textline " "
|
|
bitfld.long 0x4 3. " DRCT_LOCK ,Lock bit" "Unlocked,Locked"
|
|
bitfld.long 0x4 1.--2. " DRCT_DISP_NUM ,Accessed display number" "Display 0,Display 1,Display 2,?..."
|
|
textline " "
|
|
bitfld.long 0x4 0. " DRCT_RS ,Display command/data address signal" "RS=0,RS=1"
|
|
hgroup.long 0x1BC++0x3
|
|
hide.long 0x00 "DI_DISP_LLA_DATA,DI Display Low Level Access Data Register"
|
|
in
|
|
tree.end
|
|
tree.end
|
|
group.long 0x200++0x3
|
|
line.long 0x00 "IPU_GP_REG, IPU general Purpose register"
|
|
hexmask.long 0x00 4.--31. 1. " IPU_GP_REG ,General purpose bits"
|
|
textline " "
|
|
bitfld.long 0x00 3. " BE_PIN_SEL ,This control bit enables 24bit interface with byte enable support" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " D2_BE_POL ,This bit controls the polarity of the BE signal" "Straight,Inverse"
|
|
textline " "
|
|
bitfld.long 0x00 1. " D1_BE_POL ,This bit controls the polarity of the BE signal" "Straight,Inverse"
|
|
bitfld.long 0x00 0. " D0_BE_POL ,This bit controls the polarity of the BE signal" "Straight,Inverse"
|
|
width 0xB
|
|
tree.end
|
|
tree "SPDIF (Sony/Philips Digital Interface)"
|
|
base ad:0x50028000
|
|
width 9.
|
|
group.long 0x00++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SCR,Configuration Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SCR ,Configuration Register"
|
|
bitfld.long 0x0 23. " RCVFIFO_CTRL ,Receive FIFO Control" "Normal,Always-0"
|
|
bitfld.long 0x0 22. " RCVFIFO_OFF/ON ,Receive FIFO Off/On" "On,Off"
|
|
textline " "
|
|
bitfld.long 0x0 21. " RCVFIFO_RST ,Receive FIFO Reset" "Normal,Reset to 1 sample"
|
|
textline " "
|
|
bitfld.long 0x0 19.--20. " RCVFIFOFULL_SEL ,Receive FIFO Full Select" "Samples>=1,Samples>=4,Samples>=8,Samples>=16"
|
|
textline " "
|
|
bitfld.long 0x0 18. " RCVAUTOSYNC ,Receive FIFO Auto Sync Enable" "Disabled,Enabled"
|
|
bitfld.long 0x0 17. " TXAUTOSYNC ,Transmit FIFO Auto Sync Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 15.--16. " TXFIFOEMPTY_SEL ,Transmit FIFO Empty Select" "Samples<=0,Samples<=4,Samples<=8,Samples<=12"
|
|
bitfld.long 0x0 13. " LOWPOWER ,Low-power mode" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 12. " SOFT_RESET ,SPDIF software reset" "Not reset,Reset"
|
|
bitfld.long 0x0 10.--11. " TXFIFO_CTRL ,Transmit FIFO Control" "Tx Digital 0,Normal,Reset to 1 samp,?..."
|
|
textline " "
|
|
bitfld.long 0x0 9. " PDIRRCV ,DMA Receive Request" "Not performed,Performed"
|
|
bitfld.long 0x0 8. " PDIRTX ,DMA Transmit Request" "Not performed,Performed"
|
|
textline " "
|
|
bitfld.long 0x0 5. " VALCTRL ,Outgoing Validity Control" "Set,Cleared"
|
|
bitfld.long 0x0 2.--4. " TXSEL ,Transmit Select" "Disabled,SPDIFIN,Reserved,Reserved,Reserved,Normal,?..."
|
|
textline " "
|
|
bitfld.long 0x0 0.--1. " USRCSEL ,User Channel Source Select" "Disabled,SPDIF Rcv Block,Reserved,OnChip Transmitter"
|
|
group.long 0x04++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRCD,CDText Control Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRCD ,CDText Control Register"
|
|
bitfld.long 0x0 1. " USYNCMODE ,User Channel Sync Mode" "Non-CD Data,CD User Ch subcode"
|
|
if (((d.tb(ad:0x50028000+0x08))&0x40)==0x40)
|
|
group.long 0x08++0x03
|
|
textline ""
|
|
; line.tbyte 0x0 "SRPC,Phase Configuration Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRPC ,Phase Configuration Register"
|
|
bitfld.long 0x0 7.--10. " CLKSRC_SEL ,Clock source selection" "SPDIF_RcvClk,SPDIF_RcvClk,SPDIF_RcvClk,SPDIF_RcvClk,Reserved,CCM audio,CCM MUX,EASI hckt,IOMUX,?..."
|
|
bitfld.long 0x0 6. " LOCK ,Internal DPLL lock" "Not locked,Locked"
|
|
textline " "
|
|
bitfld.long 0x00 3.--5. " GAINSEL ,Gain selection" "24*2^10,16*2^10,12*2^10,8*2^10,6*2^10,4*2^10,3*2^10,?..."
|
|
else
|
|
group.long 0x08++0x03
|
|
textline ""
|
|
; line.tbyte 0x0 "SRPC,FreqMeas Configuration Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRPC ,FreqMeas Configuration Register"
|
|
bitfld.long 0x0 7.--10. " CLKSRCSEL ,Clock source selection" "CCM audio,CCM MUX,ESAI hckt,IOMUX,Reserved,CCM audio,CCM MUX,ESAI hckt,IOMUX,?..."
|
|
bitfld.long 0x0 6. " LOCK ,Internal DPLL lock" "Not locked,Locked"
|
|
textline " "
|
|
bitfld.long 0x00 3.--5. " GAINSEL ,Gain selection" "24*2^10,16*2^10,12*2^10,8*2^10,6*2^10,4*2^10,3*2^10,?..."
|
|
endif
|
|
group.long 0x0c++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SIE,Interrupt Enable Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SIE ,Interrupt Enable Register"
|
|
bitfld.long 0x0 20. " LOCK ,SPDIF receiver's DPLL is locked" "Disabled,Enabled"
|
|
bitfld.long 0x0 19. " TXUNOV ,SPDIF transmit FIFO is under/overrun" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 18. " TXRESYN ,SPDIF transmit FIFO resync" "Disabled,Enabled"
|
|
bitfld.long 0x0 17. " CNEW ,SPDIF receive change in value of control channel" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 16. " VALNOGOOD ,SPDIF validity flag is no good" "Disabled,Enabled"
|
|
bitfld.long 0x0 15. " SYMERR ,SPDIF receiver found illegal symbol" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 14. " BITERR ,SPDIF receiver found parity bit error" "Disabled,Enabled"
|
|
bitfld.long 0x0 10. " URXFUL ,UChannel receive register is full" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 9. " URXOV ,UChannel receive register is overrun" "Disabled,Enabled"
|
|
bitfld.long 0x0 8. " QRXFUL ,QChannel receive register is full" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 7. " QRXOV ,QChannel receive register is overrun" "Disabled,Enabled"
|
|
bitfld.long 0x0 6. " UQSYNC ,U/Q Channel sync is found" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 5. " UQERR ,U/Q Channel framing error" "Disabled,Enabled"
|
|
bitfld.long 0x0 4. " PDIRUNOV ,Processor data input underrun/overrun occurred" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 3. " PDIRRESYN ,Processor data input resync" "Disabled,Enabled"
|
|
bitfld.long 0x0 2. " LOCKLOSS ,SPDIF receiver loss of lock has occurred" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x0 1. " TXEM ,SPDIF transmit FIFO is empty" "Disabled,Enabled"
|
|
bitfld.long 0x0 0. " PDIRFUL ,Processor data input is full" "Disabled,Enabled"
|
|
group.long 0x10++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SIS/SIC, Interrupt Status/Clear Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SIS/SIC , Interrupt Status/Clear Register"
|
|
eventfld.long 0x0 20. " LOCK ,SPDIF receiver's DPLL is locked" "Not occurred,Occurred"
|
|
eventfld.long 0x0 19. " TXUNOV ,SPDIF transmit FIFO is under/overrun" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 18. " TXRESYN ,SPDIF transmit FIFO resync" "Not occurred,Occurred"
|
|
eventfld.long 0x0 17. " CNEW ,SPDIF receive change in value of control channel" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 16. " VALNOGOOD ,SPDIF validity flag is no good" "Not occurred,Occurred"
|
|
eventfld.long 0x0 15. " SYMERR ,SPDIF receiver found illegal symbol" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 14. " BITERR ,SPDIF receiver found parity bit error" "Not occurred,Occurred"
|
|
bitfld.long 0x0 10. " URXFUL ,UChannel receive register is full" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 9. " URXOV ,UChannel receive register is overrun" "Not occurred,Occurred"
|
|
bitfld.long 0x0 8. " QRXFUL ,QChannel receive register is full" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 7. " QRXOV ,QChannel receive register is overrun" "Not occurred,Occurred"
|
|
eventfld.long 0x0 6. " UQSYNC ,U/Q Channel sync is found" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 5. " UQERR ,U/Q Channel framing error" "Not occurred,Occurred"
|
|
eventfld.long 0x0 4. " PDIRUNOV ,Processor data input underrun/overrun occurred" "Not occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x0 3. " PDIRRESYN ,Processor data input resync" "Not occurred,Occurred"
|
|
eventfld.long 0x0 2. " LOCKLOSS ,SPDIF receiver loss of lock has occurred" "Not occurred,Occurred"
|
|
textline " "
|
|
bitfld.long 0x0 1. " TXEM ,SPDIF transmit FIFO is empty" "Not occurred,Occurred"
|
|
bitfld.long 0x0 0. " PDIRFUL ,Processor data input is full" "Not occurred,Occurred"
|
|
rgroup.long 0x14++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRL,SPDIF Left Channel Data Receiver"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRL ,SPDIF Left Channel Data Receiver"
|
|
rgroup.long 0x18++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRR,SPDIF Right Channel Data Receiver"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRR ,SPDIF Right Channel Data Receiver"
|
|
rgroup.long 0x1C++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRCSH,SPDIF C Channel Data Receiver High [47:24]"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRCSH ,SPDIF C Channel Data Receiver High [47:24]"
|
|
rgroup.long 0x20++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRCSL,SPDIF C Channel Data Receiver Low [0:23]"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRCSL ,SPDIF C Channel Data Receiver Low [0:23]"
|
|
rgroup.long 0x24++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRU,SPDIF U Channel Data Receiver"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRU ,SPDIF U Channel Data Receiver"
|
|
rgroup.long 0x28++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRQ,SPDIF Q Channel Data Receiver"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRQ ,SPDIF Q Channel Data Receiver"
|
|
rgroup.long 0x2C++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "STL,SPDIF Left Channel Data Transmitter"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "STL ,SPDIF Left Channel Data Transmitter"
|
|
rgroup.long 0x30++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "STR,SPDIF Right Channel Data Transmitter"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "STR ,SPDIF Right Channel Data Transmitter"
|
|
rgroup.long 0x34++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "STCSCH,SPDIF Consumer C Channel Data Transmitter High[47:24]"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "STCSCH ,SPDIF Consumer C Channel Data Transmitter High[47:24]"
|
|
rgroup.long 0x38++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "STCSCL,SPDIF Consumer C Channel Data Transmitter Low[23:0]"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "STCSCL ,SPDIF Consumer C Channel Data Transmitter Low[23:0]"
|
|
group.long 0x44++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "SRFM,Frequency Measurement Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "SRFM ,Frequency Measurement Register"
|
|
group.long 0x50++0x3
|
|
textline ""
|
|
; line.tbyte 0x0 "STC,Transmit Clock Control Register"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. "STC ,Transmit Clock Control Register"
|
|
hexmask.long.word 0x0 11.--19. 1. " SYSCLK_DF ,System Clock Divider Factor"
|
|
bitfld.long 0x0 8.--10. " TXCLK_SRC , Transmit Clock Source" "CCM audio,CCM Mux,ESAI hckt,IOMUX,Reserved,Freq Divided ipg_clk,?..."
|
|
textline " "
|
|
hexmask.long.byte 0x0 0.--6. 1. " TXCLK_DF ,Divider factor"
|
|
width 0xb
|
|
tree.end
|
|
tree.open "SSI (Synchronous Serial Interface)"
|
|
tree "SSI 1"
|
|
base ad:0x43fa0000
|
|
width 8.
|
|
group.long 0x00++0x7
|
|
line.long 0x00 "STX0,Transmit Data Register 0"
|
|
line.long 0x04 "STX1,Transmit Data Register 1"
|
|
hgroup.long 0x08++0x3
|
|
hide.long 0x00 "SRX0,Receive Data Register 0"
|
|
in
|
|
hgroup.long 0xC++0x3
|
|
hide.long 0x0 "SRX1,Receive Data Register 1"
|
|
in
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "SCR,SSI Control Register"
|
|
bitfld.long 0x0 12. " SYNC_TX_FS ,Safe window for TE to be visible to the internal circuit" "Not latched,Latched"
|
|
textline " "
|
|
bitfld.long 0x0 11. " RFR_CLK_DIS ,Receive Frame Clock Disable" "Enabled,Disabled"
|
|
bitfld.long 0x0 10. " TFR_CLK_DIS ,Transmit Frame Clock Disable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " CLK_IST ,Clock Idle State" "Low,High"
|
|
bitfld.long 0x00 8. " TCH_EN ,Two Channel Operation Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SYS_CLK_EN ,System Clock Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5.--6. " I2S_MODE[1:0] ,I2S Mode Select" "Normal,I2S master,I2S slave,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 4. " SYN ,Synchronous Mode" "Asynchronous,Synchronous"
|
|
bitfld.long 0x00 3. " NET ,Network Mode" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RE ,Receive Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " TE ,Transmit Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SSIEN ,SSI Enable" "Disabled,Enabled"
|
|
hgroup.long 0x14++0x3
|
|
hide.long 0x00 "SISR,SSI Interrupt Status Register"
|
|
in
|
|
group.long 0x18++0x17
|
|
line.long 0x00 "SIER,SSI Interrupt Enable Register"
|
|
bitfld.long 0x00 24. " RFRC ,Receive Frame Complete" "Disabled,Enabled"
|
|
bitfld.long 0x00 23. " TFRC ,Transmit Frame Complete" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " RDMAE ,Receive DMA Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " RIE ,Receive Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " TDMAE ,Transmit DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " TIE ,Transmit Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " CMDAU ,Command Address Register Updated" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " CMDDU ,Command Data Register Updated" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " RXT ,Receive Tag Updated" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " RDR1 ,Receive Data Ready 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " RDR0 ,Receive Data Ready 0" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TDE1 ,Transmit Data Register Empty 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " TDE0 ,Transmit Data Register Empty 0" "Disabled,Enabled"
|
|
bitfld.long 0x00 11. " ROE1 ,Receiver Overrun Error 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " ROE0 ,Receiver Overrun Error 0" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " TUE1 ,Transmitter Underrun Error 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " TUE0 ,Transmitter Underrun Error 0 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " TFS ,Transmit Frame Sync Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RFS ,Receive Frame Sync Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " TLS ,Transmit Last Time Slot Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " RLS ,Receive Last Time Slot Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " RFF1 ,Receive FIFO Full 1 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " RFF0 ,Receive FIFO Full 0 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " TFE1 ,Transmit FIFO Empty 1 Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TFE0 ,Transmit FIFO Empty 0 Interrupt Enable" "Disabled,Enabled"
|
|
line.long 0x04 "STCR,SSI Transmit Configuration Register"
|
|
bitfld.long 0x04 9. " TXBIT0 ,Transmit Bit 0" "Bit 31|15,Bit 0"
|
|
bitfld.long 0x04 8. " TFEN1 ,Transmit FIFO Enable 1" "Disabled,Enabled"
|
|
bitfld.long 0x04 7. " TFEN0 ,Transmit FIFO Enable 0" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 6. " TFDIR ,Transmit Frame Direction" "External,Internal"
|
|
bitfld.long 0x04 5. " TXDIR ,Transmit Clock Direction" "External,Internal"
|
|
bitfld.long 0x04 4. " TSHFD ,Transmit Shift Direction" "MSB first,LSB first"
|
|
textline " "
|
|
bitfld.long 0x04 3. " TSCKP ,Transmit Clock Polarity" "Rising edge,Falling edge"
|
|
bitfld.long 0x04 2. " TFSI ,Transmit Frame Sync Invert" "Active high,Active low"
|
|
bitfld.long 0x04 1. " TFSL ,Transmit Frame Sync Length" "One-word,One-clock-bit"
|
|
textline " "
|
|
bitfld.long 0x04 0. " TEFS ,Transmit Early Frame Sync" "First bit,One before"
|
|
line.long 0x08 "SRCR,SSI Receive Configuration Register"
|
|
bitfld.long 0x8 10. " RXEXT ,Receive Data Extension" "Not extended,Extended"
|
|
bitfld.long 0x08 9. " RXBIT0 ,Receive Bit 0" "Bit 31|15,Bit 0"
|
|
bitfld.long 0x08 8. " RFEN1 ,Receive FIFO Enable 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " RFEN0 ,Receive FIFO Enable 0" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " RFDIR ,Receive Frame Direction" "External,Internal"
|
|
bitfld.long 0x08 5. " RXDIR ,Receive Clock Direction" "External,Internal"
|
|
textline " "
|
|
bitfld.long 0x08 4. " RSHFD ,Receive Shift Direction" "MSB first,LSB first"
|
|
bitfld.long 0x08 3. " RSCKP ,Receive Clock Polarity" "Falling edge,Rising edge"
|
|
bitfld.long 0x08 2. " RFSI ,Receive Frame Sync Invert" "Active high,Active low"
|
|
textline " "
|
|
bitfld.long 0x08 1. " RFSL ,Receive Frame Sync Length" "One-word,One-clock-bit"
|
|
bitfld.long 0x08 0. " REFS ,Receive Early Frame Sync" "First bit,One before"
|
|
line.long 0x0c "STCCR,SSI Transmit Clock Control Register"
|
|
bitfld.long 0x0c 18. " DIV2 ,Divide By 2" "Bypassed,Div by 2"
|
|
bitfld.long 0x0c 17. " PSR ,Prescaler Range" "Bypassed,Div by 8"
|
|
bitfld.long 0x0c 13.--16. " WL[3:0] ,Word Length Control" "Reserved,Reserved,Reserved,8,10,12,Reserved,16,18,20,22,24,?..."
|
|
textline " "
|
|
bitfld.long 0x0c 8.--12. " DC[4:0] ,Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
hexmask.long.byte 0x0c 0.--7. 1. " PM[7:0] ,Prescaler Modulus Select"
|
|
line.long 0x10 "SRCCR,SSI Receive Clock Control Register"
|
|
bitfld.long 0x10 18. " DIV2 ,Divide By 2" "Bypassed,Div by 2"
|
|
bitfld.long 0x10 17. " PSR ,Prescaler Range" "Bypassed,Div by 8"
|
|
bitfld.long 0x10 13.--16. " WL[3:0] ,Word Length Control" "Reserved,Reserved,Reserved,8,10,12,Reserved,16,18,20,22,24,?..."
|
|
textline " "
|
|
bitfld.long 0x10 8.--12. " DC[4:0] ,Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PM[7:0] ,Prescaler Modulus Select"
|
|
line.long 0x14 "SFCSR,SSI FIFO Control/Status Register"
|
|
bitfld.long 0x14 28.--31. " RFCNT1[3:0] ,Receive FIFO Counter 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 24.--27. " TFCNT1[3:0] ,Transmit FIFO Counter 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 20.--23. " RFWM1[3:0] ,Receive FIFO Full WaterMark 1" "Reserved,>= 1,>= 2,>= 3,>= 4,>= 5,>= 6,>= 7,>= 8,>= 9,>= 10,>= 11,>= 12,>= 13,>= 14,= 15"
|
|
textline " "
|
|
bitfld.long 0x14 16.--19. " TFWM1[3:0] ,Transmit FIFO Empty WaterMark 1" "Reserved,<= 14,<= 13,<= 12,<= 11,<= 10,<= 9,<= 8,<= 7,<= 6,<= 5,<= 4,<= 3,<= 2,<= 1,= 0"
|
|
bitfld.long 0x14 12.--15. " RFCNT0[3:0] ,Receive FIFO Counter 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 8.--11. " TFCNT0[3:0] ,Transmit FIFO Counter 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x14 4.--7. " RFWM0[3:0] ,Receive FIFO Full WaterMark 0" "Reserved,>= 1,>= 2,>= 3,>= 4,>= 5,>= 6,>= 7,>= 8,>= 9,>= 10,>= 11,>= 12,>= 13,>= 14,= 15"
|
|
bitfld.long 0x14 0.--3. " TFWM0[3:0] ,Transmit FIFO Empty WaterMark 0" "Reserved,<= 14,<= 13,<= 12,<= 11,<= 10,<= 9,<= 8,<= 7,<= 6,<= 5,<= 4,<= 3,<= 2,<= 1,= 0"
|
|
group.long 0x30++0x7
|
|
line.long 0x00 "STR,SSI Test Register"
|
|
bitfld.long 0x00 15. " TEST ,Test Mode" "No effect,Enabled"
|
|
bitfld.long 0x00 14. " RCK2TCK ,Receive Clock to Transmit Clock Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 13. " RFS2TFS ,Receive Frame to Transmit Frame Loop Back" "No effect,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " RXSTATE ,Receiver State Machine Status" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
bitfld.long 0x00 7. " TXD2RXD ,Transmit Data to Receive Data Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 6. " TCK2RCK ,Transmit Clock to Receive Clock Loop Back" "No effect,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " TFS2RFS ,Transmit Frame to Receive Frame Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 0.--4. " TXSTATE ,Transmitter State Machine Status" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
line.long 0x04 "SOR,SSI Option Register"
|
|
bitfld.long 0x04 6. " CLKOFF ,Clock Off" "No effect,Off"
|
|
bitfld.long 0x04 5. " RX_CLR ,Receiver Clear" "No effect,Flushed"
|
|
bitfld.long 0x04 4. " TX_CLR ,Transmitter Clear" "No effect,Flushed"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INIT ,Initialize" "No effect,Initialized"
|
|
bitfld.long 0x04 1.--2. " WAIT ,Number wait states" "0,1,2,3"
|
|
bitfld.long 0x04 0. " SYNRST ,Frame Sync Reset" "No reset,Reset"
|
|
group.long 0x38++0x3
|
|
line.long 0x00 "SACNT,SSI AC97 Control Register"
|
|
hexmask.long.byte 0x00 5.--10. 1. " FRDIV[5:0] ,Frame Rate Divider"
|
|
bitfld.long 0x00 4. " WR ,Write Command" "Not attached,Attached"
|
|
bitfld.long 0x00 3. " RD ,Read Command" "Not attached,Attached"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TIF ,Tag in FIFO" "SATAG,Rx FIFO 0"
|
|
bitfld.long 0x00 1. " FV ,Fixed/Variable Operation" "Fixed,Variable"
|
|
bitfld.long 0x00 0. " AC97EN ,AC97 Mode Enable" "Disabled,Enabled"
|
|
hgroup.long 0x3c++0x03
|
|
hide.long 0x00 "SACADD,SSI AC97 Command Address Register"
|
|
in
|
|
hgroup.long 0x40++0x03
|
|
hide.long 0x00 "SACDAT,SSI AC97 Command Data Register"
|
|
in
|
|
hgroup.long 0x44++0x03
|
|
hide.long 0x00 "SATAG,SSI AC97 Tag Register"
|
|
in
|
|
group.long 0x48++0x07
|
|
line.long 0x00 "STMSK,SSI Transmit Time Slot Mask Register"
|
|
bitfld.long 0x00 31. " STMSK ,Transmit Mask Bit 31" "0,1"
|
|
bitfld.long 0x00 30. ",Transmit Mask Bit 30" "0,1"
|
|
bitfld.long 0x00 29. ",Transmit Mask Bit 29" "0,1"
|
|
bitfld.long 0x00 28. ",Transmit Mask Bit 28" "0,1"
|
|
bitfld.long 0x00 27. ",Transmit Mask Bit 27" "0,1"
|
|
bitfld.long 0x00 26. ",Transmit Mask Bit 26" "0,1"
|
|
bitfld.long 0x00 25. ",Transmit Mask Bit 25" "0,1"
|
|
bitfld.long 0x00 24. ",Transmit Mask Bit 24" "0,1"
|
|
bitfld.long 0x00 23. ",Transmit Mask Bit 23" "0,1"
|
|
bitfld.long 0x00 22. ",Transmit Mask Bit 22" "0,1"
|
|
bitfld.long 0x00 21. ",Transmit Mask Bit 21" "0,1"
|
|
bitfld.long 0x00 20. ",Transmit Mask Bit 20" "0,1"
|
|
bitfld.long 0x00 19. ",Transmit Mask Bit 19" "0,1"
|
|
bitfld.long 0x00 18. ",Transmit Mask Bit 18" "0,1"
|
|
bitfld.long 0x00 17. ",Transmit Mask Bit 17" "0,1"
|
|
bitfld.long 0x00 16. ",Transmit Mask Bit 16" "0,1"
|
|
bitfld.long 0x00 15. ",Transmit Mask Bit 15" "0,1"
|
|
bitfld.long 0x00 14. ",Transmit Mask Bit 14" "0,1"
|
|
bitfld.long 0x00 13. ",Transmit Mask Bit 13" "0,1"
|
|
bitfld.long 0x00 12. ",Transmit Mask Bit 12" "0,1"
|
|
bitfld.long 0x00 11. ",Transmit Mask Bit 11" "0,1"
|
|
bitfld.long 0x00 10. ",Transmit Mask Bit 10" "0,1"
|
|
bitfld.long 0x00 9. ",Transmit Mask Bit 9" "0,1"
|
|
bitfld.long 0x00 8. ",Transmit Mask Bit 8" "0,1"
|
|
bitfld.long 0x00 7. ",Transmit Mask Bit 7" "0,1"
|
|
bitfld.long 0x00 6. ",Transmit Mask Bit 6" "0,1"
|
|
bitfld.long 0x00 5. ",Transmit Mask Bit 5" "0,1"
|
|
bitfld.long 0x00 4. ",Transmit Mask Bit 4" "0,1"
|
|
bitfld.long 0x00 3. ",Transmit Mask Bit 3" "0,1"
|
|
bitfld.long 0x00 2. ",Transmit Mask Bit 2" "0,1"
|
|
bitfld.long 0x00 1. ",Transmit Mask Bit 1" "0,1"
|
|
bitfld.long 0x00 0. ",Transmit Mask Bit 0" "0,1"
|
|
line.long 0x04 "SRMSK,SSI Receive Time Slot Mask Register"
|
|
bitfld.long 0x04 31. " SRMSK ,Receive Mask Bit 31" "0,1"
|
|
bitfld.long 0x04 30. ",Receive Mask Bit 30" "0,1"
|
|
bitfld.long 0x04 29. ",Receive Mask Bit 29" "0,1"
|
|
bitfld.long 0x04 28. ",Receive Mask Bit 28" "0,1"
|
|
bitfld.long 0x04 27. ",Receive Mask Bit 27" "0,1"
|
|
bitfld.long 0x04 26. ",Receive Mask Bit 26" "0,1"
|
|
bitfld.long 0x04 25. ",Receive Mask Bit 25" "0,1"
|
|
bitfld.long 0x04 24. ",Receive Mask Bit 24" "0,1"
|
|
bitfld.long 0x04 23. ",Receive Mask Bit 23" "0,1"
|
|
bitfld.long 0x04 22. ",Receive Mask Bit 22" "0,1"
|
|
bitfld.long 0x04 21. ",Receive Mask Bit 21" "0,1"
|
|
bitfld.long 0x04 20. ",Receive Mask Bit 20" "0,1"
|
|
bitfld.long 0x04 19. ",Receive Mask Bit 19" "0,1"
|
|
bitfld.long 0x04 18. ",Receive Mask Bit 18" "0,1"
|
|
bitfld.long 0x04 17. ",Receive Mask Bit 17" "0,1"
|
|
bitfld.long 0x04 16. ",Receive Mask Bit 16" "0,1"
|
|
bitfld.long 0x04 15. ",Receive Mask Bit 15" "0,1"
|
|
bitfld.long 0x04 14. ",Receive Mask Bit 14" "0,1"
|
|
bitfld.long 0x04 13. ",Receive Mask Bit 13" "0,1"
|
|
bitfld.long 0x04 12. ",Receive Mask Bit 12" "0,1"
|
|
bitfld.long 0x04 11. ",Receive Mask Bit 11" "0,1"
|
|
bitfld.long 0x04 10. ",Receive Mask Bit 10" "0,1"
|
|
bitfld.long 0x04 9. ",Receive Mask Bit 9" "0,1"
|
|
bitfld.long 0x04 8. ",Receive Mask Bit 8" "0,1"
|
|
bitfld.long 0x04 7. ",Receive Mask Bit 7" "0,1"
|
|
bitfld.long 0x04 6. ",Receive Mask Bit 6" "0,1"
|
|
bitfld.long 0x04 5. ",Receive Mask Bit 5" "0,1"
|
|
bitfld.long 0x04 4. ",Receive Mask Bit 4" "0,1"
|
|
bitfld.long 0x04 3. ",Receive Mask Bit 3" "0,1"
|
|
bitfld.long 0x04 2. ",Receive Mask Bit 2" "0,1"
|
|
bitfld.long 0x04 1. ",Receive Mask Bit 1" "0,1"
|
|
bitfld.long 0x04 0. ",Receive Mask Bit 0" "0,1"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "SACCST,SSI AC97 Channel Status Register"
|
|
setclrfld.long 0x0 9. 0x4 9. 0x8 9. " SACCST9_set/clr ,AC97 Channel Status 9" "Disabled,Enabled"
|
|
setclrfld.long 0x0 8. 0x4 8. 0x8 8. " SACCST8_set/clr ,AC97 Channel Status 8" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 7. 0x4 7. 0x8 7. " SACCST7_set/clr ,AC97 Channel Status 7" "Disabled,Enabled"
|
|
setclrfld.long 0x0 6. 0x4 6. 0x8 6. " SACCST6_set/clr ,AC97 Channel Status 6" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 5. 0x4 5. 0x8 5. " SACCST5_set/clr ,AC97 Channel Status 5" "Disabled,Enabled"
|
|
setclrfld.long 0x0 4. 0x4 4. 0x8 4. " SACCST4_set/clr ,AC97 Channel Status 4" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 3. 0x4 3. 0x8 3. " SACCST3_set/clr ,AC97 Channel Status 3" "Disabled,Enabled"
|
|
setclrfld.long 0x0 2. 0x4 2. 0x8 2. " SACCST2_set/clr ,AC97 Channel Status 2" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 1. 0x4 1. 0x8 1. " SACCST1_set/clr ,AC97 Channel Status 1" "Disabled,Enabled"
|
|
setclrfld.long 0x0 0. 0x4 0. 0x8 0. " SACCST0_set/clr ,AC97 Channel Status 0" "Disabled,Enabled"
|
|
width 10.
|
|
width 0xb
|
|
tree.end
|
|
tree "SSI 2"
|
|
base ad:0x50014000
|
|
width 8.
|
|
group.long 0x00++0x7
|
|
line.long 0x00 "STX0,Transmit Data Register 0"
|
|
line.long 0x04 "STX1,Transmit Data Register 1"
|
|
hgroup.long 0x08++0x3
|
|
hide.long 0x00 "SRX0,Receive Data Register 0"
|
|
in
|
|
hgroup.long 0xC++0x3
|
|
hide.long 0x0 "SRX1,Receive Data Register 1"
|
|
in
|
|
group.long 0x10++0x3
|
|
line.long 0x00 "SCR,SSI Control Register"
|
|
bitfld.long 0x0 12. " SYNC_TX_FS ,Safe window for TE to be visible to the internal circuit" "Not latched,Latched"
|
|
textline " "
|
|
bitfld.long 0x0 11. " RFR_CLK_DIS ,Receive Frame Clock Disable" "Enabled,Disabled"
|
|
bitfld.long 0x0 10. " TFR_CLK_DIS ,Transmit Frame Clock Disable" "Enabled,Disabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " CLK_IST ,Clock Idle State" "Low,High"
|
|
bitfld.long 0x00 8. " TCH_EN ,Two Channel Operation Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 7. " SYS_CLK_EN ,System Clock Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5.--6. " I2S_MODE[1:0] ,I2S Mode Select" "Normal,I2S master,I2S slave,Normal"
|
|
textline " "
|
|
bitfld.long 0x00 4. " SYN ,Synchronous Mode" "Asynchronous,Synchronous"
|
|
bitfld.long 0x00 3. " NET ,Network Mode" "Not selected,Selected"
|
|
textline " "
|
|
bitfld.long 0x00 2. " RE ,Receive Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " TE ,Transmit Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " SSIEN ,SSI Enable" "Disabled,Enabled"
|
|
hgroup.long 0x14++0x3
|
|
hide.long 0x00 "SISR,SSI Interrupt Status Register"
|
|
in
|
|
group.long 0x18++0x17
|
|
line.long 0x00 "SIER,SSI Interrupt Enable Register"
|
|
bitfld.long 0x00 24. " RFRC ,Receive Frame Complete" "Disabled,Enabled"
|
|
bitfld.long 0x00 23. " TFRC ,Transmit Frame Complete" "Disabled,Enabled"
|
|
bitfld.long 0x00 22. " RDMAE ,Receive DMA Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 21. " RIE ,Receive Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 20. " TDMAE ,Transmit DMA Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 19. " TIE ,Transmit Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 18. " CMDAU ,Command Address Register Updated" "Disabled,Enabled"
|
|
bitfld.long 0x00 17. " CMDDU ,Command Data Register Updated" "Disabled,Enabled"
|
|
bitfld.long 0x00 16. " RXT ,Receive Tag Updated" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 15. " RDR1 ,Receive Data Ready 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 14. " RDR0 ,Receive Data Ready 0" "Disabled,Enabled"
|
|
bitfld.long 0x00 13. " TDE1 ,Transmit Data Register Empty 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 12. " TDE0 ,Transmit Data Register Empty 0" "Disabled,Enabled"
|
|
bitfld.long 0x00 11. " ROE1 ,Receiver Overrun Error 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 10. " ROE0 ,Receiver Overrun Error 0" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 9. " TUE1 ,Transmitter Underrun Error 1" "Disabled,Enabled"
|
|
bitfld.long 0x00 8. " TUE0 ,Transmitter Underrun Error 0 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 7. " TFS ,Transmit Frame Sync Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " RFS ,Receive Frame Sync Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 5. " TLS ,Transmit Last Time Slot Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 4. " RLS ,Receive Last Time Slot Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 3. " RFF1 ,Receive FIFO Full 1 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " RFF0 ,Receive FIFO Full 0 Interrupt Enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " TFE1 ,Transmit FIFO Empty 1 Interrupt Enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " TFE0 ,Transmit FIFO Empty 0 Interrupt Enable" "Disabled,Enabled"
|
|
line.long 0x04 "STCR,SSI Transmit Configuration Register"
|
|
bitfld.long 0x04 9. " TXBIT0 ,Transmit Bit 0" "Bit 31|15,Bit 0"
|
|
bitfld.long 0x04 8. " TFEN1 ,Transmit FIFO Enable 1" "Disabled,Enabled"
|
|
bitfld.long 0x04 7. " TFEN0 ,Transmit FIFO Enable 0" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x04 6. " TFDIR ,Transmit Frame Direction" "External,Internal"
|
|
bitfld.long 0x04 5. " TXDIR ,Transmit Clock Direction" "External,Internal"
|
|
bitfld.long 0x04 4. " TSHFD ,Transmit Shift Direction" "MSB first,LSB first"
|
|
textline " "
|
|
bitfld.long 0x04 3. " TSCKP ,Transmit Clock Polarity" "Rising edge,Falling edge"
|
|
bitfld.long 0x04 2. " TFSI ,Transmit Frame Sync Invert" "Active high,Active low"
|
|
bitfld.long 0x04 1. " TFSL ,Transmit Frame Sync Length" "One-word,One-clock-bit"
|
|
textline " "
|
|
bitfld.long 0x04 0. " TEFS ,Transmit Early Frame Sync" "First bit,One before"
|
|
line.long 0x08 "SRCR,SSI Receive Configuration Register"
|
|
bitfld.long 0x8 10. " RXEXT ,Receive Data Extension" "Not extended,Extended"
|
|
bitfld.long 0x08 9. " RXBIT0 ,Receive Bit 0" "Bit 31|15,Bit 0"
|
|
bitfld.long 0x08 8. " RFEN1 ,Receive FIFO Enable 1" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 7. " RFEN0 ,Receive FIFO Enable 0" "Disabled,Enabled"
|
|
bitfld.long 0x08 6. " RFDIR ,Receive Frame Direction" "External,Internal"
|
|
bitfld.long 0x08 5. " RXDIR ,Receive Clock Direction" "External,Internal"
|
|
textline " "
|
|
bitfld.long 0x08 4. " RSHFD ,Receive Shift Direction" "MSB first,LSB first"
|
|
bitfld.long 0x08 3. " RSCKP ,Receive Clock Polarity" "Falling edge,Rising edge"
|
|
bitfld.long 0x08 2. " RFSI ,Receive Frame Sync Invert" "Active high,Active low"
|
|
textline " "
|
|
bitfld.long 0x08 1. " RFSL ,Receive Frame Sync Length" "One-word,One-clock-bit"
|
|
bitfld.long 0x08 0. " REFS ,Receive Early Frame Sync" "First bit,One before"
|
|
line.long 0x0c "STCCR,SSI Transmit Clock Control Register"
|
|
bitfld.long 0x0c 18. " DIV2 ,Divide By 2" "Bypassed,Div by 2"
|
|
bitfld.long 0x0c 17. " PSR ,Prescaler Range" "Bypassed,Div by 8"
|
|
bitfld.long 0x0c 13.--16. " WL[3:0] ,Word Length Control" "Reserved,Reserved,Reserved,8,10,12,Reserved,16,18,20,22,24,?..."
|
|
textline " "
|
|
bitfld.long 0x0c 8.--12. " DC[4:0] ,Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
hexmask.long.byte 0x0c 0.--7. 1. " PM[7:0] ,Prescaler Modulus Select"
|
|
line.long 0x10 "SRCCR,SSI Receive Clock Control Register"
|
|
bitfld.long 0x10 18. " DIV2 ,Divide By 2" "Bypassed,Div by 2"
|
|
bitfld.long 0x10 17. " PSR ,Prescaler Range" "Bypassed,Div by 8"
|
|
bitfld.long 0x10 13.--16. " WL[3:0] ,Word Length Control" "Reserved,Reserved,Reserved,8,10,12,Reserved,16,18,20,22,24,?..."
|
|
textline " "
|
|
bitfld.long 0x10 8.--12. " DC[4:0] ,Frame Rate Divider Control" "1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32"
|
|
hexmask.long.byte 0x10 0.--7. 1. " PM[7:0] ,Prescaler Modulus Select"
|
|
line.long 0x14 "SFCSR,SSI FIFO Control/Status Register"
|
|
bitfld.long 0x14 28.--31. " RFCNT1[3:0] ,Receive FIFO Counter 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 24.--27. " TFCNT1[3:0] ,Transmit FIFO Counter 1" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 20.--23. " RFWM1[3:0] ,Receive FIFO Full WaterMark 1" "Reserved,>= 1,>= 2,>= 3,>= 4,>= 5,>= 6,>= 7,>= 8,>= 9,>= 10,>= 11,>= 12,>= 13,>= 14,= 15"
|
|
textline " "
|
|
bitfld.long 0x14 16.--19. " TFWM1[3:0] ,Transmit FIFO Empty WaterMark 1" "Reserved,<= 14,<= 13,<= 12,<= 11,<= 10,<= 9,<= 8,<= 7,<= 6,<= 5,<= 4,<= 3,<= 2,<= 1,= 0"
|
|
bitfld.long 0x14 12.--15. " RFCNT0[3:0] ,Receive FIFO Counter 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x14 8.--11. " TFCNT0[3:0] ,Transmit FIFO Counter 0" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
bitfld.long 0x14 4.--7. " RFWM0[3:0] ,Receive FIFO Full WaterMark 0" "Reserved,>= 1,>= 2,>= 3,>= 4,>= 5,>= 6,>= 7,>= 8,>= 9,>= 10,>= 11,>= 12,>= 13,>= 14,= 15"
|
|
bitfld.long 0x14 0.--3. " TFWM0[3:0] ,Transmit FIFO Empty WaterMark 0" "Reserved,<= 14,<= 13,<= 12,<= 11,<= 10,<= 9,<= 8,<= 7,<= 6,<= 5,<= 4,<= 3,<= 2,<= 1,= 0"
|
|
group.long 0x30++0x7
|
|
line.long 0x00 "STR,SSI Test Register"
|
|
bitfld.long 0x00 15. " TEST ,Test Mode" "No effect,Enabled"
|
|
bitfld.long 0x00 14. " RCK2TCK ,Receive Clock to Transmit Clock Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 13. " RFS2TFS ,Receive Frame to Transmit Frame Loop Back" "No effect,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 8.--12. " RXSTATE ,Receiver State Machine Status" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
bitfld.long 0x00 7. " TXD2RXD ,Transmit Data to Receive Data Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 6. " TCK2RCK ,Transmit Clock to Receive Clock Loop Back" "No effect,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 5. " TFS2RFS ,Transmit Frame to Receive Frame Loop Back" "No effect,Enabled"
|
|
bitfld.long 0x00 0.--4. " TXSTATE ,Transmitter State Machine Status" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
line.long 0x04 "SOR,SSI Option Register"
|
|
bitfld.long 0x04 6. " CLKOFF ,Clock Off" "No effect,Off"
|
|
bitfld.long 0x04 5. " RX_CLR ,Receiver Clear" "No effect,Flushed"
|
|
bitfld.long 0x04 4. " TX_CLR ,Transmitter Clear" "No effect,Flushed"
|
|
textline " "
|
|
bitfld.long 0x04 3. " INIT ,Initialize" "No effect,Initialized"
|
|
bitfld.long 0x04 1.--2. " WAIT ,Number wait states" "0,1,2,3"
|
|
bitfld.long 0x04 0. " SYNRST ,Frame Sync Reset" "No reset,Reset"
|
|
group.long 0x38++0x3
|
|
line.long 0x00 "SACNT,SSI AC97 Control Register"
|
|
hexmask.long.byte 0x00 5.--10. 1. " FRDIV[5:0] ,Frame Rate Divider"
|
|
bitfld.long 0x00 4. " WR ,Write Command" "Not attached,Attached"
|
|
bitfld.long 0x00 3. " RD ,Read Command" "Not attached,Attached"
|
|
textline " "
|
|
bitfld.long 0x00 2. " TIF ,Tag in FIFO" "SATAG,Rx FIFO 0"
|
|
bitfld.long 0x00 1. " FV ,Fixed/Variable Operation" "Fixed,Variable"
|
|
bitfld.long 0x00 0. " AC97EN ,AC97 Mode Enable" "Disabled,Enabled"
|
|
hgroup.long 0x3c++0x03
|
|
hide.long 0x00 "SACADD,SSI AC97 Command Address Register"
|
|
in
|
|
hgroup.long 0x40++0x03
|
|
hide.long 0x00 "SACDAT,SSI AC97 Command Data Register"
|
|
in
|
|
hgroup.long 0x44++0x03
|
|
hide.long 0x00 "SATAG,SSI AC97 Tag Register"
|
|
in
|
|
group.long 0x48++0x07
|
|
line.long 0x00 "STMSK,SSI Transmit Time Slot Mask Register"
|
|
bitfld.long 0x00 31. " STMSK ,Transmit Mask Bit 31" "0,1"
|
|
bitfld.long 0x00 30. ",Transmit Mask Bit 30" "0,1"
|
|
bitfld.long 0x00 29. ",Transmit Mask Bit 29" "0,1"
|
|
bitfld.long 0x00 28. ",Transmit Mask Bit 28" "0,1"
|
|
bitfld.long 0x00 27. ",Transmit Mask Bit 27" "0,1"
|
|
bitfld.long 0x00 26. ",Transmit Mask Bit 26" "0,1"
|
|
bitfld.long 0x00 25. ",Transmit Mask Bit 25" "0,1"
|
|
bitfld.long 0x00 24. ",Transmit Mask Bit 24" "0,1"
|
|
bitfld.long 0x00 23. ",Transmit Mask Bit 23" "0,1"
|
|
bitfld.long 0x00 22. ",Transmit Mask Bit 22" "0,1"
|
|
bitfld.long 0x00 21. ",Transmit Mask Bit 21" "0,1"
|
|
bitfld.long 0x00 20. ",Transmit Mask Bit 20" "0,1"
|
|
bitfld.long 0x00 19. ",Transmit Mask Bit 19" "0,1"
|
|
bitfld.long 0x00 18. ",Transmit Mask Bit 18" "0,1"
|
|
bitfld.long 0x00 17. ",Transmit Mask Bit 17" "0,1"
|
|
bitfld.long 0x00 16. ",Transmit Mask Bit 16" "0,1"
|
|
bitfld.long 0x00 15. ",Transmit Mask Bit 15" "0,1"
|
|
bitfld.long 0x00 14. ",Transmit Mask Bit 14" "0,1"
|
|
bitfld.long 0x00 13. ",Transmit Mask Bit 13" "0,1"
|
|
bitfld.long 0x00 12. ",Transmit Mask Bit 12" "0,1"
|
|
bitfld.long 0x00 11. ",Transmit Mask Bit 11" "0,1"
|
|
bitfld.long 0x00 10. ",Transmit Mask Bit 10" "0,1"
|
|
bitfld.long 0x00 9. ",Transmit Mask Bit 9" "0,1"
|
|
bitfld.long 0x00 8. ",Transmit Mask Bit 8" "0,1"
|
|
bitfld.long 0x00 7. ",Transmit Mask Bit 7" "0,1"
|
|
bitfld.long 0x00 6. ",Transmit Mask Bit 6" "0,1"
|
|
bitfld.long 0x00 5. ",Transmit Mask Bit 5" "0,1"
|
|
bitfld.long 0x00 4. ",Transmit Mask Bit 4" "0,1"
|
|
bitfld.long 0x00 3. ",Transmit Mask Bit 3" "0,1"
|
|
bitfld.long 0x00 2. ",Transmit Mask Bit 2" "0,1"
|
|
bitfld.long 0x00 1. ",Transmit Mask Bit 1" "0,1"
|
|
bitfld.long 0x00 0. ",Transmit Mask Bit 0" "0,1"
|
|
line.long 0x04 "SRMSK,SSI Receive Time Slot Mask Register"
|
|
bitfld.long 0x04 31. " SRMSK ,Receive Mask Bit 31" "0,1"
|
|
bitfld.long 0x04 30. ",Receive Mask Bit 30" "0,1"
|
|
bitfld.long 0x04 29. ",Receive Mask Bit 29" "0,1"
|
|
bitfld.long 0x04 28. ",Receive Mask Bit 28" "0,1"
|
|
bitfld.long 0x04 27. ",Receive Mask Bit 27" "0,1"
|
|
bitfld.long 0x04 26. ",Receive Mask Bit 26" "0,1"
|
|
bitfld.long 0x04 25. ",Receive Mask Bit 25" "0,1"
|
|
bitfld.long 0x04 24. ",Receive Mask Bit 24" "0,1"
|
|
bitfld.long 0x04 23. ",Receive Mask Bit 23" "0,1"
|
|
bitfld.long 0x04 22. ",Receive Mask Bit 22" "0,1"
|
|
bitfld.long 0x04 21. ",Receive Mask Bit 21" "0,1"
|
|
bitfld.long 0x04 20. ",Receive Mask Bit 20" "0,1"
|
|
bitfld.long 0x04 19. ",Receive Mask Bit 19" "0,1"
|
|
bitfld.long 0x04 18. ",Receive Mask Bit 18" "0,1"
|
|
bitfld.long 0x04 17. ",Receive Mask Bit 17" "0,1"
|
|
bitfld.long 0x04 16. ",Receive Mask Bit 16" "0,1"
|
|
bitfld.long 0x04 15. ",Receive Mask Bit 15" "0,1"
|
|
bitfld.long 0x04 14. ",Receive Mask Bit 14" "0,1"
|
|
bitfld.long 0x04 13. ",Receive Mask Bit 13" "0,1"
|
|
bitfld.long 0x04 12. ",Receive Mask Bit 12" "0,1"
|
|
bitfld.long 0x04 11. ",Receive Mask Bit 11" "0,1"
|
|
bitfld.long 0x04 10. ",Receive Mask Bit 10" "0,1"
|
|
bitfld.long 0x04 9. ",Receive Mask Bit 9" "0,1"
|
|
bitfld.long 0x04 8. ",Receive Mask Bit 8" "0,1"
|
|
bitfld.long 0x04 7. ",Receive Mask Bit 7" "0,1"
|
|
bitfld.long 0x04 6. ",Receive Mask Bit 6" "0,1"
|
|
bitfld.long 0x04 5. ",Receive Mask Bit 5" "0,1"
|
|
bitfld.long 0x04 4. ",Receive Mask Bit 4" "0,1"
|
|
bitfld.long 0x04 3. ",Receive Mask Bit 3" "0,1"
|
|
bitfld.long 0x04 2. ",Receive Mask Bit 2" "0,1"
|
|
bitfld.long 0x04 1. ",Receive Mask Bit 1" "0,1"
|
|
bitfld.long 0x04 0. ",Receive Mask Bit 0" "0,1"
|
|
group.long 0x50++0x3
|
|
line.long 0x0 "SACCST,SSI AC97 Channel Status Register"
|
|
setclrfld.long 0x0 9. 0x4 9. 0x8 9. " SACCST9_set/clr ,AC97 Channel Status 9" "Disabled,Enabled"
|
|
setclrfld.long 0x0 8. 0x4 8. 0x8 8. " SACCST8_set/clr ,AC97 Channel Status 8" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 7. 0x4 7. 0x8 7. " SACCST7_set/clr ,AC97 Channel Status 7" "Disabled,Enabled"
|
|
setclrfld.long 0x0 6. 0x4 6. 0x8 6. " SACCST6_set/clr ,AC97 Channel Status 6" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 5. 0x4 5. 0x8 5. " SACCST5_set/clr ,AC97 Channel Status 5" "Disabled,Enabled"
|
|
setclrfld.long 0x0 4. 0x4 4. 0x8 4. " SACCST4_set/clr ,AC97 Channel Status 4" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 3. 0x4 3. 0x8 3. " SACCST3_set/clr ,AC97 Channel Status 3" "Disabled,Enabled"
|
|
setclrfld.long 0x0 2. 0x4 2. 0x8 2. " SACCST2_set/clr ,AC97 Channel Status 2" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x0 1. 0x4 1. 0x8 1. " SACCST1_set/clr ,AC97 Channel Status 1" "Disabled,Enabled"
|
|
setclrfld.long 0x0 0. 0x4 0. 0x8 0. " SACCST0_set/clr ,AC97 Channel Status 0" "Disabled,Enabled"
|
|
width 10.
|
|
width 0xb
|
|
tree.end
|
|
tree.end
|
|
tree "Z160 GPU"
|
|
base ad:0x20000000
|
|
width 30.
|
|
wgroup.long 0x00++0x03
|
|
line.long 0x00 "VGC_COMMANDSTREAM,VGC_COMMANDSTREAM"
|
|
wgroup.long 0xFF0++0x03
|
|
line.long 0x00 "VGC_MMUCOMMANDSTREAM,VGC_MMUCOMMANDSTREAM"
|
|
group.long 0x1BC++0x03
|
|
line.long 0x00 "VGV2_LAST,VGV2_LAST"
|
|
bitfld.long 0x00 0. " DUMMY ,DUMMY" "0,1"
|
|
group.long 0x100++0x03
|
|
line.long 0x00 "VGV2_FIRST,VGV2_FIRST"
|
|
bitfld.long 0x00 0. " DUMMY ,DUMMY" "0,1"
|
|
group.long 0x1C0++0x03
|
|
line.long 0x00 "VGV3_FIRST,VGV3_FIRST"
|
|
bitfld.long 0x00 0. " DUMMY ,DUMMY" "0,1"
|
|
rgroup.long 0x1000++0x03
|
|
line.long 0x00 "VGC_REVISION,VGC_REVISION"
|
|
hexmask.long.byte 0x00 4.--7. 1. " MAJOR_REVISION ,Major revision ID"
|
|
hexmask.long.byte 0x00 0.--3. 1. " MINOR_REVISION ,Minor revision ID"
|
|
rgroup.long 0x1040++0x03
|
|
line.long 0x00 "VGC_SYSSTATUS,VGC_SYSSTATUS"
|
|
bitfld.long 0x00 0. " RESET ,Internal reset state" "No reset,Reset"
|
|
group.long 0x1060++0x03
|
|
line.long 0x00 "VGC_IRQSTATUS,VGC_IRQSTATUS"
|
|
bitfld.long 0x00 3. " FBC ,FFBC done interrupt status" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 2. " FIFO ,FIFO full error interrupt status" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x00 1. " G2D ,2D idle request interrupt status" "No interrupt,Interrupt"
|
|
bitfld.long 0x00 0. " MH ,MH AXI error/MMU page fault interrupt status" "No interrupt,Interrupt"
|
|
group.long 0x10E0++0x03
|
|
line.long 0x00 "VGC_IRQENABLE,VGC_IRQENABLE"
|
|
bitfld.long 0x00 3. " FBC ,FFBC done interrupt enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 2. " FIFO ,FIFO full error interrupt enable" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 1. " G2D ,2D idle request interrupt enable" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " MH ,MH AXI error/MMU page fault interrupt enable" "Disabled,Enabled"
|
|
rgroup.long 0x1380++0x03
|
|
line.long 0x00 "VGC_IRQ_ACTIVE_CNT,VGC_IRQ_ACTIVE_CNT"
|
|
hexmask.long.byte 0x00 24.--31. 1. " FBC ,FFBC done interrupt counter"
|
|
hexmask.long.byte 0x00 16.--23. 1. " FIFO ,FIFO full error interrupt counter"
|
|
textline " "
|
|
hexmask.long.byte 0x00 8.--15. 1. " G2D ,2D idle request interrupt counter"
|
|
hexmask.long.byte 0x00 0.--7. 1. " MH ,MH AXI error/MMU page fault interrupt counter"
|
|
group.long 0x1420++0x03
|
|
line.long 0x00 "VGC_CLOCKEN,VGC_CLOCKEN"
|
|
bitfld.long 0x00 2. " VG_L1L2 ,Enable VG level 1 and level 2 clock" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " G2D_VGL3 ,Enable 2D and VG level 3 clock" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 0. " BCACHE ,Enable burst cache clock" "Disabled,Enabled"
|
|
wgroup.long 0x1440++0x03
|
|
line.long 0x00 "MMU_READ_ADDR,MMU_READ_ADDR"
|
|
hexmask.long.word 0x00 0.--14. 1. " ADDR ,Register Address"
|
|
hgroup.long 0x1460++0x03
|
|
hide.long 0x00 "MMU_READ_DATA,MMU_READ_DATA"
|
|
in
|
|
rgroup.long 0x1F00++0x03
|
|
line.long 0x00 "VGC_FIFOFREE,VGC_FIFOFREE"
|
|
bitfld.long 0x00 0. " FREE ,Free space in input fifo" "0,1"
|
|
base ad:((per.l(ad:0x20000000))&0xffffffff)
|
|
tree "Command Stream Registers"
|
|
wgroup.long 0x00++0x03
|
|
line.long 0x00 "G2D_BASE0,G2D_BASE0"
|
|
wgroup.long 0x08++0x03
|
|
line.long 0x00 "G2D_BASE1,G2D_BASE1"
|
|
wgroup.long 0x10++0x03
|
|
line.long 0x00 "G2D_BASE2,G2D_BASE2"
|
|
wgroup.long 0x18++0x03
|
|
line.long 0x00 "G2D_BASE3,G2D_BASE3"
|
|
wgroup.long 0x04++0x03
|
|
line.long 0x00 "G2D_CFG0,G2D_CFG0"
|
|
bitfld.long 0x00 23. " STRIDESIGN ,Stride sign bit" "0,1"
|
|
bitfld.long 0x00 22. " SWAPBITS ,Swap order of bits or nibbles in bytes" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " SWAPRB ,Swap red and blue components after conversion" "0,1"
|
|
bitfld.long 0x00 20. " SWAPALL ,ARGB -> BGRA swap" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " SWAPBYTES ,Swap read bytes in 32-bit value before conversion" "0,1"
|
|
bitfld.long 0x00 18. " SWAPWORDS ,Swap read words in 32-bit value before conversion" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRGB ,Surface is in sRGB format" "0,1"
|
|
bitfld.long 0x00 16. " TILED ,TILED" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " FORMAT ,FORMAT" "G2D_1,G2D_1BW,G2D_4,G2D_8,G2D_4444,G2D_1555,G2D_0565,G2D_8888,G2D_YUY2,G2D_UYVY,G2D_YVYU,G2D_4444_RGBA,G2D_5551_RGBA,G2D_8888_RGBA,G2D_A8,?..."
|
|
hexmask.long.word 0x00 0.--11. 1. " STRIDE ,STRIDE"
|
|
wgroup.long 0x0C++0x03
|
|
line.long 0x00 "G2D_CFG1,G2D_CFG1"
|
|
bitfld.long 0x00 23. " STRIDESIGN ,Stride sign bit" "0,1"
|
|
bitfld.long 0x00 22. " SWAPBITS ,Swap order of bits or nibbles in bytes" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " SWAPRB ,Swap red and blue components after conversion" "0,1"
|
|
bitfld.long 0x00 20. " SWAPALL ,ARGB -> BGRA swap" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " SWAPBYTES ,Swap read bytes in 32-bit value before conversion" "0,1"
|
|
bitfld.long 0x00 18. " SWAPWORDS ,Swap read words in 32-bit value before conversion" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRGB ,Surface is in sRGB format" "0,1"
|
|
bitfld.long 0x00 16. " TILED ,TILED" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " FORMAT ,FORMAT" "G2D_1,G2D_1BW,G2D_4,G2D_8,G2D_4444,G2D_1555,G2D_0565,G2D_8888,G2D_YUY2,G2D_UYVY,G2D_YVYU,G2D_4444_RGBA,G2D_5551_RGBA,G2D_8888_RGBA,G2D_A8,?..."
|
|
hexmask.long.word 0x00 0.--11. 1. " STRIDE ,STRIDE"
|
|
wgroup.long 0x14++0x03
|
|
line.long 0x00 "G2D_CFG2,G2D_CFG2"
|
|
bitfld.long 0x00 23. " STRIDESIGN ,Stride sign bit" "0,1"
|
|
bitfld.long 0x00 22. " SWAPBITS ,Swap order of bits or nibbles in bytes" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " SWAPRB ,Swap red and blue components after conversion" "0,1"
|
|
bitfld.long 0x00 20. " SWAPALL ,ARGB -> BGRA swap" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " SWAPBYTES ,Swap read bytes in 32-bit value before conversion" "0,1"
|
|
bitfld.long 0x00 18. " SWAPWORDS ,Swap read words in 32-bit value before conversion" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRGB ,Surface is in sRGB format" "0,1"
|
|
bitfld.long 0x00 16. " TILED ,TILED" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " FORMAT ,FORMAT" "G2D_1,G2D_1BW,G2D_4,G2D_8,G2D_4444,G2D_1555,G2D_0565,G2D_8888,G2D_YUY2,G2D_UYVY,G2D_YVYU,G2D_4444_RGBA,G2D_5551_RGBA,G2D_8888_RGBA,G2D_A8,?..."
|
|
hexmask.long.word 0x00 0.--11. 1. " STRIDE ,STRIDE"
|
|
wgroup.long 0x1C++0x2B
|
|
line.long 0x00 "G2D_CFG3,G2D_CFG3"
|
|
bitfld.long 0x00 23. " STRIDESIGN ,Stride sign bit" "0,1"
|
|
bitfld.long 0x00 22. " SWAPBITS ,Swap order of bits or nibbles in bytes" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " SWAPRB ,Swap red and blue components after conversion" "0,1"
|
|
bitfld.long 0x00 20. " SWAPALL ,ARGB -> BGRA swap" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " SWAPBYTES ,Swap read bytes in 32-bit value before conversion" "0,1"
|
|
bitfld.long 0x00 18. " SWAPWORDS ,Swap read words in 32-bit value before conversion" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " SRGB ,Surface is in sRGB format" "0,1"
|
|
bitfld.long 0x00 16. " TILED ,TILED" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 12.--15. " FORMAT ,FORMAT" "G2D_1,G2D_1BW,G2D_4,G2D_8,G2D_4444,G2D_1555,G2D_0565,G2D_8888,G2D_YUY2,G2D_UYVY,G2D_YVYU,G2D_4444_RGBA,G2D_5551_RGBA,G2D_8888_RGBA,G2D_A8,?..."
|
|
hexmask.long.word 0x00 0.--11. 1. " STRIDE ,STRIDE"
|
|
line.long 0x04 "G2D_SCISSORX,G2D_SCISSORX"
|
|
hexmask.long.word 0x04 11.--21. 1. " RIGHT ,RIGHT"
|
|
hexmask.long.word 0x04 0.--10. 1. " LEFT ,LEFT"
|
|
line.long 0x08 "G2D_SCISSORY,G2D_SCISSORY"
|
|
hexmask.long.word 0x08 11.--21. 1. " BOTTOM ,BOTTOM"
|
|
hexmask.long.word 0x08 0.--10. 1. " TOP ,TOP"
|
|
line.long 0x0C "G2D_FOREGROUND,G2D_FOREGROUND"
|
|
line.long 0x10 "G2D_BACKGROUND,G2D_BACKGROUND"
|
|
line.long 0x14 "G2D_ALPHABLEND,G2D_ALPHABLEND"
|
|
bitfld.long 0x14 15. " MASKTOALPHA ,Route mask to alpha" "0,1"
|
|
bitfld.long 0x14 14. " PREMULTIPLYDST ,Premultiply destination color" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 13. " INVERTMASK ,Invert mask value" "0,1"
|
|
bitfld.long 0x14 12. " MODULATE ,Modulate mask to alpha" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 11. " OPTIMIZE ,Optimize reads based on color alpha value before ROP" "0,1"
|
|
bitfld.long 0x14 10. " INVERT ,Invert alpha value" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 9. " CONSTANT ,Use constant alpha value" "0,1"
|
|
bitfld.long 0x14 8. " OBS_ENABLE ,Obsolete: Enable alpha blend, enable blender instead" "0,1"
|
|
textline " "
|
|
hexmask.long.byte 0x14 0.--7. 1. " ALPHA ,Constant alpha value"
|
|
line.long 0x18 "G2D_ROP,G2D_ROP"
|
|
hexmask.long.word 0x18 0.--15. 1. " ROP ,Raster Operation"
|
|
line.long 0x1C "G2D_CONFIG,G2D_CONFIG"
|
|
bitfld.long 0x1C 19. " NOPROTECT ,Don't use protect for destination reads" "0,1"
|
|
bitfld.long 0x1C 18. " NOLASTPIXEL ,Don't draw last pixel of a line (for polylines)" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 17. " PALMLINES ,Draw lines according to PalmOS rules (default WinCE)" "0,1"
|
|
bitfld.long 0x1C 16. " ALPHATEX ,Take only alpha from texture 0, apply color from input" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 12.--15. " ARGBMASK ,ARGBMASK" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x1C 11. " WRITESRGB ,Write sRGB color" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 10. " DITHER ,Dither the output" "0,1"
|
|
bitfld.long 0x1C 9. " IGNORECKALPHA ,Ignore alpha in color key compare" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 8. " OBS_GAMMA ,Obsolete: Gamma correct 4-bit bitmap, use SRGB instead" "0,1"
|
|
bitfld.long 0x1C 6.--7. " ROTATE ,Destination rotate" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x1C 5. " DSTCK ,Destination color key" "0,1"
|
|
bitfld.long 0x1C 4. " SRCCK ,Source color key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 3. " SRC3 ,Read source 3" "0,1"
|
|
bitfld.long 0x1C 2. " SRC2 ,Read source 2" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 1. " SRC1 ,Read source 1" "0,1"
|
|
bitfld.long 0x1C 0. " DST ,Read destination" "0,1"
|
|
line.long 0x20 "G2D_INPUT,G2D_INPUT"
|
|
bitfld.long 0x20 5. " LINEMODE ,Draw lines instead of rectangles" "0,1"
|
|
bitfld.long 0x20 4. " VGMODE ,Input is assumed to be generated by V1 and uses slightly different protocol" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 3. " COPYCOORD ,Copy destination coordinates to unsent source coordinates too" "0,1"
|
|
bitfld.long 0x20 2. " SCOORD2 ,Source coordinate 2 in input (for pattern)" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 1. " SCOORD1 ,Source coordinate 1 in input" "0,1"
|
|
bitfld.long 0x20 0. " COLOR ,Constant color field in input" "0,1"
|
|
line.long 0x24 "G2D_MASK,G2D_MASK"
|
|
hexmask.long.word 0x24 12.--23. 1. " XMASK ,Mask for second source X coordinate"
|
|
hexmask.long.word 0x24 0.--11. 1. " YMASK ,Mask for second source Y coordinate"
|
|
line.long 0x28 "G2D_BLENDERCFG,G2D_BLENDERCFG"
|
|
bitfld.long 0x28 8. " NOMASK ,Don't perform mask blending" "0,1"
|
|
bitfld.long 0x28 7. " OBS_DIVALPHA ,Obsolete: Take divider from TEMP0 alpha instead of TEMP1" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 6. " OOALPHA ,One Over Alpha: Divide TEMP0 by TEMP1 after blend program (inverse premultiply)" "0,1"
|
|
bitfld.long 0x28 5. " ENABLE ,Enable blender" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 3.--4. " ALPHAPASSES ,Number of alpha passes" "0,1,2,3"
|
|
bitfld.long 0x28 0.--2. " PASSES ,Number of passes" "0,1,2,3,4,5,6,7"
|
|
wgroup.long 0x50++0x47
|
|
line.long 0x00 "G2D_BLEND_A0,G2D_BLEND_A0"
|
|
bitfld.long 0x00 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x00 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x00 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x00 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x00 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x00 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x00 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x00 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x00 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x00 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x00 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x00 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x00 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x00 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x04 "G2D_BLEND_A1,G2D_BLEND_A1"
|
|
bitfld.long 0x04 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x04 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x04 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x04 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x04 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x04 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x04 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x04 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x04 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x04 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x04 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x04 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x04 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x04 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x08 "G2D_BLEND_A2,G2D_BLEND_A2"
|
|
bitfld.long 0x08 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x08 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x08 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x08 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x08 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x08 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x08 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x08 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x08 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x08 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x08 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x08 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x08 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x08 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x08 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x0C "G2D_BLEND_A3,G2D_BLEND_A3"
|
|
bitfld.long 0x0C 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x0C 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x0C 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x0C 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x0C 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x0C 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x0C 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x0C 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x0C 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x0C 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x0C 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x0C 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x0C 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x0C 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x0C 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x10 "G2D_BLEND_C0,G2D_BLEND_C0"
|
|
bitfld.long 0x10 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x10 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x10 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x10 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x10 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x10 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x10 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x10 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x10 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x10 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x10 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x10 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x10 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x10 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x14 "G2D_BLEND_C1,G2D_BLEND_C1"
|
|
bitfld.long 0x14 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x14 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x14 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x14 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x14 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x14 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x14 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x14 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x14 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x14 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x14 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x14 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x14 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x14 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x14 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x18 "G2D_BLEND_C2,G2D_BLEND_C2"
|
|
bitfld.long 0x18 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x18 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x18 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x18 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x18 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x18 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x18 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x18 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x18 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x18 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x18 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x18 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x18 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x18 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x18 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x1C "G2D_BLEND_C3,G2D_BLEND_C3"
|
|
bitfld.long 0x1C 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x1C 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x1C 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x1C 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x1C 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x1C 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x1C 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x1C 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x1C 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x1C 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x1C 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x1C 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x1C 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x1C 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x1C 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x20 "G2D_BLEND_C4,G2D_BLEND_C4"
|
|
bitfld.long 0x20 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x20 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x20 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x20 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x20 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x20 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x20 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x20 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x20 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x20 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x20 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x20 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x20 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x20 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x20 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x24 "G2D_BLEND_C5,G2D_BLEND_C5"
|
|
bitfld.long 0x24 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x24 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x24 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x24 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x24 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x24 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x24 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x24 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x24 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x24 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x24 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x24 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x24 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x24 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x24 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x28 "G2D_BLEND_C6,G2D_BLEND_C6"
|
|
bitfld.long 0x28 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x28 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x28 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x28 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x28 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x28 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x28 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x28 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x28 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x28 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x28 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x28 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x28 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x28 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x28 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x2C "G2D_BLEND_C7,G2D_BLEND_C7"
|
|
bitfld.long 0x2C 31. " CONST_D , Constant used for SRC D" "0,1"
|
|
bitfld.long 0x2C 30. " CONST_C , Constant used for SRC C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 29. " CONST_B , Constant used for SRC B" "0,1"
|
|
bitfld.long 0x2C 28. " CONST_A , Constant used for SRC A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 25.--27. " SRC_D ,Source D register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x2C 22.--24. " SRC_C ,Source C register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x2C 19.--21. " SRC_B ,Source B register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
bitfld.long 0x2C 16.--18. " SRC_A ,Source A register" "G2D_BLENDSRC_ZERO,G2D_BLENDSRC_SOURCE,G2D_BLENDSRC_DESTINATION,G2D_BLENDSRC_IMAGE,G2D_BLENDSRC_TEMP0,G2D_BLENDSRC_TEMP1,G2D_BLENDSRC_TEMP2,G2D_BLENDSRC_MASK"
|
|
textline " "
|
|
bitfld.long 0x2C 15. " INV_D ,Invert (1-x) argument D" "0,1"
|
|
bitfld.long 0x2C 14. " INV_C ,Invert (1-x) argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 13. " INV_B ,Invert (1-x) argument B" "0,1"
|
|
bitfld.long 0x2C 12. " INV_A ,Invert (1-x) argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 11. " AR_D ,Alpha replicate argument D" "0,1"
|
|
bitfld.long 0x2C 10. " AR_C ,Alpha replicate argument C" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 9. " AR_B ,Alpha replicate argument B" "0,1"
|
|
bitfld.long 0x2C 8. " AR_A ,Alpha replicate argument A" "0,1"
|
|
textline " "
|
|
bitfld.long 0x2C 6.--7. " DST_C ,C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x2C 4.--5. " DST_B ,A*B result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
textline " "
|
|
bitfld.long 0x2C 2.--3. " DST_A ,A*B op C*D result destination register" "G2D_BLENDSRC_IGNORE,G2D_BLENDDST_TEMP0,G2D_BLENDDST_TEMP1,G2D_BLENDDST_TEMP2"
|
|
bitfld.long 0x2C 0.--1. " OPERATION ,Operation" "G2D_BLENDOP_ADD,G2D_BLENDOP_SUB,G2D_BLENDOP_MIN,G2D_BLENDOP_MAX"
|
|
line.long 0x30 "VGV1_VTX0,VGV1_VTX0"
|
|
hexmask.long.word 0x30 16.--31. 1. " Y ,Vertex 0(1) Y coordinate"
|
|
hexmask.long.word 0x30 0.--15. 1. " X ,Vertex 0(1) X coordinate"
|
|
line.long 0x34 "VGV1_VTX1,VGV1_VTX1"
|
|
hexmask.long.word 0x34 16.--31. 1. " Y ,Vertex 0(1) Y coordinate"
|
|
hexmask.long.word 0x34 0.--15. 1. " X ,Vertex 0(1) X coordinate"
|
|
line.long 0x38 "VGV1_TILEOFS,VGV1_TILEOFS"
|
|
bitfld.long 0x38 24. " LEFTMOST ,The leftmost tile" "0,1"
|
|
hexmask.long.word 0x38 12.--23. 1. " Y ,Tile Y offset"
|
|
textline " "
|
|
hexmask.long.word 0x38 0.--11. 1. " X ,Tile X offset"
|
|
line.long 0x3C "VGV1_FILL,VGV1_FILL"
|
|
bitfld.long 0x3C 0. " INHERIT ,Inherit the winding counters to the next tile" "0,1"
|
|
line.long 0x40 "VGV1_SCISSORX,VGV1_SCISSORX"
|
|
hexmask.long.word 0x40 16.--26. 1. " RIGHT ,Scissor right edge"
|
|
bitfld.long 0x40 11.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
hexmask.long.word 0x40 0.--10. 1. " LEFT ,Scissor left edge"
|
|
line.long 0x44 "VGV1_SCISSORY,VGV1_SCISSORY"
|
|
hexmask.long.word 0x44 16.--26. 1. " BOTTOM ,Scissor bottom edge"
|
|
bitfld.long 0x44 11.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
hexmask.long.word 0x44 0.--10. 1. " TOP ,Scissor top edge"
|
|
wgroup.long 0x9C++0x13
|
|
line.long 0x00 "VGV1_CFG1,VGV1_CFG1"
|
|
bitfld.long 0x00 0. " WINDRULE ,Polygon fill rule" "Non-zero,Odd-even"
|
|
line.long 0x04 "VGV1_CFG2,VGV1_CFG2"
|
|
bitfld.long 0x04 0.--1. " AAMODE ,AAMODE" "None,16x edge AA,Flipquad,"
|
|
line.long 0x08 "VGV1_DIRTYBASE,VGV1_DIRTYBASE"
|
|
line.long 0x0C "VGV1_CBASE1,VGV1_CBASE1"
|
|
line.long 0x10 "VGV1_UBASE2,VGV1_UBASE2"
|
|
wgroup.long 0x100++0x9F
|
|
line.long 0x00 "VGV2_C1X,VGV2_C1X"
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " F ,Implements HLINE by modifying C3X keeping C3Y unchanged"
|
|
line.long 0x04 "VGV2_C1Y,VGV2_C1Y"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " F ,Implements VLINE by modifying C3Y keeping C3X unchanged"
|
|
line.long 0x08 "VGV2_C2X,VGV2_C2X"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " F ,First controlpoint for cubic"
|
|
line.long 0x0C "VGV2_C2Y,VGV2_C2Y"
|
|
hexmask.long.tbyte 0x0C 0.--23. 1. " F ,First controlpoint for cubic"
|
|
line.long 0x10 "VGV2_C3X,VGV2_C3X"
|
|
hexmask.long.tbyte 0x10 0.--23. 1. " F ,Second controlpoint for cubic, first controlpoint for quadratic"
|
|
line.long 0x14 "VGV2_C3Y,VGV2_C3Y"
|
|
hexmask.long.tbyte 0x14 0.--23. 1. " F ,Second controlpoint for cubic, first controlpoint for quadratic"
|
|
line.long 0x18 "VGV2_C4X,VGV2_C4X"
|
|
hexmask.long.tbyte 0x18 0.--23. 1. " F ,End point (also moveto point)"
|
|
line.long 0x1C "VGV2_C4Y,VGV2_C4Y"
|
|
hexmask.long.tbyte 0x1C 0.--23. 1. " F ,End point (also moveto point)"
|
|
line.long 0x20 "VGV2_C1XREL,VGV2_C1XREL"
|
|
hexmask.long.tbyte 0x20 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x24 "VGV2_C1YREL,VGV2_C1YREL"
|
|
hexmask.long.tbyte 0x24 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x28 "VGV2_C2XREL,VGV2_C2XREL"
|
|
hexmask.long.tbyte 0x28 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x2C "VGV2_C2YREL,VGV2_C2YREL"
|
|
hexmask.long.tbyte 0x2C 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x30 "VGV2_C3XREL,VGV2_C3XREL"
|
|
hexmask.long.tbyte 0x30 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x34 "VGV2_C3YREL,VGV2_C3YREL"
|
|
hexmask.long.tbyte 0x34 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x38 "VGV2_C4XREL,VGV2_C4XREL"
|
|
hexmask.long.tbyte 0x38 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x3C "VGV2_C4YREL,VGV2_C4YREL"
|
|
hexmask.long.tbyte 0x3C 0.--23. 1. " F ,Relative to last primitive end"
|
|
line.long 0x40 "VGV2_XFXX,VGV2_XFXX"
|
|
hexmask.long.tbyte 0x40 0.--23. 1. " F ,User to surface transform matrix [r0,c0]"
|
|
line.long 0x44 "VGV2_XFYX,VGV2_XFYX"
|
|
hexmask.long.tbyte 0x44 0.--23. 1. " F ,User to surface transform matrix [r1,c0]"
|
|
line.long 0x48 "VGV2_XFXY,VGV2_XFXY"
|
|
hexmask.long.tbyte 0x48 0.--23. 1. " F ,User to surface transform matrix [r0,c1]"
|
|
line.long 0x4C "VGV2_XFYY,VGV2_XFYY"
|
|
hexmask.long.tbyte 0x4C 0.--23. 1. " F ,User to surface transform matrix [r1,c1]"
|
|
line.long 0x50 "VGV2_XFXA,VGV2_XFXA"
|
|
hexmask.long.tbyte 0x50 0.--23. 1. " F ,User to surface transform matrix [r0,c2]"
|
|
line.long 0x54 "VGV2_XFYA,VGV2_XFYA"
|
|
hexmask.long.tbyte 0x54 0.--23. 1. " F ,User to surface transform matrix [r1,c2]"
|
|
line.long 0x58 "VGV2_XFSTXX,VGV2_XFSTXX"
|
|
hexmask.long.tbyte 0x58 0.--23. 1. " F ,Stroke matrix [r0,c0]"
|
|
line.long 0x5C "VGV2_XFSTYX,VGV2_XFSTYX"
|
|
hexmask.long.tbyte 0x5C 0.--23. 1. " F ,Stroke matrix [r1,c0]"
|
|
line.long 0x60 "VGV2_XFSTXY,VGV2_XFSTXY"
|
|
hexmask.long.tbyte 0x60 0.--23. 1. " F ,Stroke matrix [r0,c1]"
|
|
line.long 0x64 "VGV2_XFSTYY,VGV2_XFSTYY"
|
|
hexmask.long.tbyte 0x64 0.--23. 1. " F ,Stroke matrix [r1,c1]"
|
|
line.long 0x68 "VGV2_BBOXMINX,VGV2_BBOXMINX"
|
|
hexmask.long.tbyte 0x68 0.--23. 1. " F ,Bounding box minimum x(y) (origo at matrix origo)"
|
|
line.long 0x6C "VGV2_BBOXMINY,VGV2_BBOXMINY"
|
|
hexmask.long.tbyte 0x6C 0.--23. 1. " F ,Bounding box minimum x(y) (origo at matrix origo)"
|
|
line.long 0x70 "VGV2_BBOXMAXX,VGV2_BBOXMAXX"
|
|
hexmask.long.tbyte 0x70 0.--23. 1. " F ,Bounding box maximum x(y) (origo at matrix origo)"
|
|
line.long 0x74 "VGV2_BBOXMAXY,VGV2_BBOXMAXY"
|
|
hexmask.long.tbyte 0x74 0.--23. 1. " F ,Bounding box maximum x(y) (origo at matrix origo)"
|
|
line.long 0x78 "VGV2_SCALE,VGV2_SCALE"
|
|
hexmask.long.tbyte 0x78 0.--23. 1. " F ,Scale for coord=incoord*scale+bias"
|
|
line.long 0x7C "VGV2_BIAS,VGV2_BIAS"
|
|
hexmask.long.tbyte 0x7C 0.--23. 1. " F ,Bias for coord=incoord*scale+bias"
|
|
line.long 0x80 "VGV2_ACCURACY,VGV2_ACCURACY"
|
|
hexmask.long.tbyte 0x80 0.--23. 1. " F ,Accuracy goal in pixels for curve splitting"
|
|
line.long 0x84 "VGV2_THINRADIUS,VGV2_THINRADIUS"
|
|
hexmask.long.tbyte 0x84 0.--23. 1. " F ,Screen space radius limit for strokes considered to be thin"
|
|
line.long 0x88 "VGV2_ARCCOS,VGV2_ARCCOS"
|
|
hexmask.long.tbyte 0x88 0.--23. 1. " F ,Round cap smoothness (cos(roundangle))"
|
|
line.long 0x8C "VGV2_ARCSIN,VGV2_ARCSIN"
|
|
hexmask.long.tbyte 0x8C 0.--23. 1. " F ,Round cap smoothness (sin(roundangle))"
|
|
line.long 0x90 "VGV2_ARCTAN,VGV2_ARCTAN"
|
|
hexmask.long.tbyte 0x90 0.--23. 1. " F ,Round cap smoothness (tan(roundangle))"
|
|
line.long 0x94 "VGV2_RADIUS,VGV2_RADIUS"
|
|
hexmask.long.tbyte 0x94 0.--23. 1. " F ,Stroke radius (in user space)"
|
|
line.long 0x98 "VGV2_MITER,VGV2_MITER"
|
|
hexmask.long.tbyte 0x98 0.--23. 1. " F ,Miter limit"
|
|
line.long 0x9C "VGV2_CLIP,VGV2_CLIP"
|
|
hexmask.long.tbyte 0x9C 0.--23. 1. " F ,Distance of clip edge from origo"
|
|
wgroup.long 0x1B8++0x3F
|
|
line.long 0x00 "VGV2_MODE,VGV2_MODE"
|
|
bitfld.long 0x00 18.--23. " EXPONENTADD ,Add value to output coordinate exponents before float_to_int conversion" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
bitfld.long 0x00 17. " SIMPLECLIP ,Disable some clip optimizations" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 16. " SIMPLESTROKE ,Disable complex stroking cases" "No,Yes"
|
|
bitfld.long 0x00 15. " SYMMETRICJOINS ,Symmetric two sided joins" "No effect,Enable"
|
|
textline " "
|
|
bitfld.long 0x00 14. " DROPOTHER ,Drop primitives on others than left sides of bounding box" "No effect,Enable"
|
|
bitfld.long 0x00 13. " DROPLEFT ,Drop primitives left of bounding box" "No effect,Enable"
|
|
textline " "
|
|
bitfld.long 0x00 12. " OPENFILL ,Allow open fill paths" "No effect,Allow"
|
|
bitfld.long 0x00 11. " NODOTS ,Disable drawing of dots for zerolenth segments" "No,Yes"
|
|
textline " "
|
|
bitfld.long 0x00 10. " FULLSPLIT ,Always split curves up to maxsplit limit" "No effect,Enable"
|
|
bitfld.long 0x00 9. " STROKESPLIT ,Enable stroke splitting mode" "No effect,Enable"
|
|
textline " "
|
|
bitfld.long 0x00 8. " STROKE ,Enable stroke mode" "No effect,Enable"
|
|
bitfld.long 0x00 6.--7. " JOIN ,Stroke join mode" "Miter,Round,Bevel,"
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " CAP ,Stroke cap mode" "Butt,Round,Square,"
|
|
bitfld.long 0x00 0.--3. " MAXSPLIT ,Limit of number of recursive splits for curves" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
line.long 0x04 "VGV2_ACTION,VGV2_ACTION"
|
|
bitfld.long 0x04 0.--3. " ACTION ,Triggers a drawing action using current coordinates" "END,MOVETOOPEN,MOVETOCLOSED,LINETO,CUBICTO,QUADTO,SCUBICTO,SQUADTO,VERTEXTO,VERTEXTOOPEN,VERTEXTOCLOSED,MOVETOMOVE,,,,FLUSH"
|
|
line.long 0x08 "VGV3_CONTROL,VGV3_CONTROL"
|
|
bitfld.long 0x08 21.--23. " DMIWAITBUF ,Pause stream reading until the given frame buffer (one hot encoded) is free" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x08 20. " V0SYNC ,Pause stream reading until sync signal received from V0" "No effect,Pause"
|
|
textline " "
|
|
bitfld.long 0x08 19. " BCFLUSH ,Flush burst cache (full flush)" "No effect,Flush"
|
|
bitfld.long 0x08 18. " WRITE ,Write current stream address to location given by VGV3_WRITEADDR" "No effect,Write"
|
|
textline " "
|
|
bitfld.long 0x08 17. " ABORT ,Abort stream reading immediately" "No effect,Abort"
|
|
bitfld.long 0x08 16. " PAUSE ,Pause stream reading after next marked packet" "No effect,Pause"
|
|
textline " "
|
|
bitfld.long 0x08 12.--15. " DMIWAITCHMASK ,Selects DMI channels which are checked for free buffer when non-zero DMIWAITBUF is given" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
hexmask.long.word 0x08 0.--11. 1. " MARKADD ,Increment mark counter by this value"
|
|
line.long 0x0C "VGV3_MODE,VGV3_MODE"
|
|
bitfld.long 0x0C 4. " DMIRESET ,Reset state of DMI interface" "No effect,Reset"
|
|
bitfld.long 0x0C 3. " DMIPAUSETYPE ,Input regwrites are blocked when V0SYNC orDMIWAITBUF is set in VGV3_CONTROL" "No effect,Block"
|
|
textline " "
|
|
bitfld.long 0x0C 2. " WRITEFLUSH ,Memory writes are done straight to L2 to make sure they arrive to memory as soon as possible" "0,1"
|
|
bitfld.long 0x0C 0. " FLIPENDIAN ,Flip dwords read from memory from big-endian to little-endian" "0,1"
|
|
line.long 0x10 "VGV3_WRITEADDR,VGV3_WRITEADDR"
|
|
line.long 0x14 "VGV3_WRITE,VGV3_WRITE"
|
|
line.long 0x18 "VGV3_WRITEIFPAUSED,VGV3_WRITEIFPAUSED"
|
|
line.long 0x1C "VGV3_NEXTADDR,VGV3_NEXTADDR"
|
|
line.long 0x20 "VGV3_NEXTCMD,VGV3_NEXTCMD"
|
|
hexmask.long.word 0x20 16.--27. 1. " CALLCOUNT ,Length of sub-stream packet in call in dwords"
|
|
bitfld.long 0x20 15. " MARK ,Mark counter is decreased by one when this packet ends" "No effect,Decrease"
|
|
textline " "
|
|
bitfld.long 0x20 12.--14. " NEXTCMD ,Action to perform after this packet" "CONTINUE,JUMP,CALL,CALLV2TRUE,CALLV2FALSE,ABORT,?..."
|
|
hexmask.long.word 0x20 0.--11. 1. " COUNT ,Length of next packet in dwords"
|
|
line.long 0x24 "VGV3_VGBYPASS,VGV3_VGBYPASS"
|
|
bitfld.long 0x24 0. " BYPASS ,Bypass V1 and V2, i.e. use only V3+2D" "No effect,Bypass"
|
|
line.long 0x28 "VGV3_WRITES8,VGV3_WRITES8"
|
|
bitfld.long 0x28 24.--26. " FORMAT ,Lower 3 bits of address specifies the format" "S8,S16,S32,F32,RAW,?..."
|
|
bitfld.long 0x28 20.--23. " ACTION ,Enable action mode where this value is sent to VGV2_ACTION register at end of each loop" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
textline " "
|
|
bitfld.long 0x28 16.--19. " LOOP ,Enable looping mode where addr is reset after every count writes" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
hexmask.long.byte 0x28 8.--15. 1. " COUNT ,Count of how many register writes to do"
|
|
textline " "
|
|
hexmask.long.byte 0x28 0.--7. 1. " ADDR ,Start register address for burst"
|
|
line.long 0x2C "VGV3_WRITES16,VGV3_WRITES16"
|
|
bitfld.long 0x2C 24.--26. " FORMAT ,Lower 3 bits of address specifies the format" "S8,S16,S32,F32,RAW,?..."
|
|
bitfld.long 0x2C 20.--23. " ACTION ,Enable action mode where this value is sent to VGV2_ACTION register at end of each loop" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
textline " "
|
|
bitfld.long 0x2C 16.--19. " LOOP ,Enable looping mode where addr is reset after every count writes" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
hexmask.long.byte 0x2C 8.--15. 1. " COUNT ,Count of how many register writes to do"
|
|
textline " "
|
|
hexmask.long.byte 0x2C 0.--7. 1. " ADDR ,Start register address for burst"
|
|
line.long 0x30 "VGV3_WRITES32,VGV3_WRITES32"
|
|
bitfld.long 0x30 24.--26. " FORMAT ,Lower 3 bits of address specifies the format" "S8,S16,S32,F32,RAW,?..."
|
|
bitfld.long 0x30 20.--23. " ACTION ,Enable action mode where this value is sent to VGV2_ACTION register at end of each loop" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
textline " "
|
|
bitfld.long 0x30 16.--19. " LOOP ,Enable looping mode where addr is reset after every count writes" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
hexmask.long.byte 0x30 8.--15. 1. " COUNT ,Count of how many register writes to do"
|
|
textline " "
|
|
hexmask.long.byte 0x30 0.--7. 1. " ADDR ,Start register address for burst"
|
|
line.long 0x34 "VGV3_WRITEF32,VGV3_WRITEF32"
|
|
bitfld.long 0x34 24.--26. " FORMAT ,Lower 3 bits of address specifies the format" "S8,S16,S32,F32,RAW,?..."
|
|
bitfld.long 0x34 20.--23. " ACTION ,Enable action mode where this value is sent to VGV2_ACTION register at end of each loop" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
textline " "
|
|
bitfld.long 0x34 16.--19. " LOOP ,Enable looping mode where addr is reset after every count writes" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
hexmask.long.byte 0x34 8.--15. 1. " COUNT ,Count of how many register writes to do"
|
|
textline " "
|
|
hexmask.long.byte 0x34 0.--7. 1. " ADDR ,Start register address for burst"
|
|
line.long 0x38 "VGV3_WRITERAW,VGV3_WRITERAW"
|
|
bitfld.long 0x38 24.--26. " FORMAT ,Lower 3 bits of address specifies the format" "S8,S16,S32,F32,RAW,?..."
|
|
bitfld.long 0x38 20.--23. " ACTION ,Enable action mode where this value is sent to VGV2_ACTION register at end of each loop" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
textline " "
|
|
bitfld.long 0x38 16.--19. " LOOP ,Enable looping mode where addr is reset after every count writes" "Disable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable,Enable"
|
|
hexmask.long.byte 0x38 8.--15. 1. " COUNT ,Count of how many register writes to do"
|
|
textline " "
|
|
hexmask.long.byte 0x38 0.--7. 1. " ADDR ,Start register address for burst"
|
|
line.long 0x3C "VGV3_WRITEDMI,VGV3_WRITEDMI"
|
|
bitfld.long 0x3C 4.--6. " BUFFER ,Set the frame buffer BUFFER as done in DMI outputs" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x3C 0.--3. " CHANMASK ,Frame buffer 'BUFFER' will be displayed on masked DMI channels" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
wgroup.long 0x1FC++0x03
|
|
line.long 0x00 "VGV3_LAST,VGV3_LAST"
|
|
bitfld.long 0x00 0. " DUMMY ,Just a dummy register used to check if address is in VGV3 range" "0,1"
|
|
wgroup.long 0x210++0x03
|
|
line.long 0x00 "FBC_BASE,FBC_BASE"
|
|
wgroup.long 0x218++0x03
|
|
line.long 0x00 "FBC_DATA,FBC_DATA"
|
|
wgroup.long 0x220++0x03
|
|
line.long 0x00 "FBC_WIDTH,FBC_WIDTH"
|
|
hexmask.long.word 0x00 0.--10. 1. " WIDTH ,Width (internal value is value + 1)"
|
|
wgroup.long 0x228++0x03
|
|
line.long 0x00 "FBC_HEIGHT,FBC_HEIGHT"
|
|
hexmask.long.word 0x00 0.--10. 1. " HEIGHT ,Height (internal value is value + 1)"
|
|
wgroup.long 0x230++0x03
|
|
line.long 0x00 "FBC_STRIDE,FBC_STRIDE"
|
|
hexmask.long.word 0x00 0.--10. 1. " STRIDE ,Stride (internal value is value + 1)"
|
|
wgroup.long 0x238++0x03
|
|
line.long 0x00 "FBC_START,FBC_START"
|
|
bitfld.long 0x00 0. " DUMMY ,Just write anything" "0,1"
|
|
wgroup.long 0x2C0++0x1F
|
|
line.long 0x00 "G2D_CONST0,G2D_CONST0"
|
|
line.long 0x04 "G2D_CONST1,G2D_CONST1"
|
|
line.long 0x08 "G2D_CONST2,G2D_CONST2"
|
|
line.long 0x0C "G2D_CONST3,G2D_CONST3"
|
|
line.long 0x10 "G2D_CONST4,G2D_CONST4"
|
|
line.long 0x14 "G2D_CONST5,G2D_CONST5"
|
|
line.long 0x18 "G2D_CONST6,G2D_CONST6"
|
|
line.long 0x1C "G2D_CONST7,G2D_CONST7"
|
|
wgroup.long 0x300++0x2F
|
|
line.long 0x00 "GRADW_CONST0,GRADW_CONST0"
|
|
hexmask.long.word 0x00 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x04 "GRADW_CONST1,GRADW_CONST1"
|
|
hexmask.long.word 0x04 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x08 "GRADW_CONST2,GRADW_CONST2"
|
|
hexmask.long.word 0x08 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x0C "GRADW_CONST3,GRADW_CONST3"
|
|
hexmask.long.word 0x0C 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x10 "GRADW_CONST4,GRADW_CONST4"
|
|
hexmask.long.word 0x10 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x14 "GRADW_CONST5,GRADW_CONST5"
|
|
hexmask.long.word 0x14 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x18 "GRADW_CONST6,GRADW_CONST6"
|
|
hexmask.long.word 0x18 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x1C "GRADW_CONST7,GRADW_CONST7"
|
|
hexmask.long.word 0x1C 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x20 "GRADW_CONST8,GRADW_CONST8"
|
|
hexmask.long.word 0x20 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x24 "GRADW_CONST9,GRADW_CONST9"
|
|
hexmask.long.word 0x24 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x28 "GRADW_CONSTA,GRADW_CONSTA"
|
|
hexmask.long.word 0x28 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
line.long 0x2C "GRADW_CONSTB,GRADW_CONSTB"
|
|
hexmask.long.word 0x2C 0.--15. 1. " VALUE ,Constant value in 1.5.10 floating point"
|
|
wgroup.long 0x340++0x13
|
|
line.long 0x00 "G2D_GRADIENT,G2D_GRADIENT"
|
|
bitfld.long 0x00 8. " SEL ,Select register window for gradient and texture unit" "0,1"
|
|
bitfld.long 0x00 7. " ENABLE2 ,Enable second texture" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 6. " ENABLE ,Enable gradient and texturing operation" "Disabled,Enabled"
|
|
bitfld.long 0x00 3.--5. " INSTRUCTIONS2 ,Number of instructions for pass 2-1" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 0.--2. " INSTRUCTIONS ,Number of instructions for pass 1-1" "0,1,2,3,4,5,6,7"
|
|
line.long 0x04 "GRADW_TEXCFG,GRADW_TEXCFG"
|
|
bitfld.long 0x04 29. " SWAPBITS ,Swap order of bits or nibbles in bytes" "0,1"
|
|
bitfld.long 0x04 28. " TEX2D ,2D texture" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 27. " SWAPRB ,Swap red and blue components after conversion" "0,1"
|
|
bitfld.long 0x04 26. " SWAPALL ,ARGB -> BGRA swap" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 25. " SWAPBYTES ,Swap read bytes in 32-bit value before conversion" "0,1"
|
|
bitfld.long 0x04 24. " SWAPWORDS ,Swap read words in 32-bit value before conversion" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 23. " PREMULTIPLY ,Premultiply colors with alpha" "0,1"
|
|
bitfld.long 0x04 22. " SRGB ,Texture is in sRGB format" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 21. " BILIN ,BILIN" "0,1"
|
|
bitfld.long 0x04 19.--20. " WRAPV ,WRAPV" "Clamp,Repeat,Mirror,Border"
|
|
textline " "
|
|
bitfld.long 0x04 17.--18. " WRAPU ,WRAPU" "Clamp,Repeat,Mirror,Border"
|
|
bitfld.long 0x04 16. " TILED ,TILED" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 12.--15. " FORMAT ,Format" "G2D_1,G2D_1BW,G2D_4,G2D_8,G2D_4444,G2D_1555,G2D_0565,G2D_8888,G2D_YUY2,G2D_UYVY,G2D_YVYU,G2D_4444_RGBA,G2D_5551_RGBA,G2D_8888_RGBA,G2D_A8,?..."
|
|
hexmask.long.word 0x04 0.--11. 1. " STRIDE ,Stride"
|
|
line.long 0x08 "GRADW_TEXSIZE,GRADW_TEXSIZE"
|
|
hexmask.long.word 0x08 11.--21. 1. " HEIGHT ,Texture height"
|
|
hexmask.long.word 0x08 0.--10. 1. " WIDTH ,Texture width"
|
|
line.long 0x0C "GRADW_TEXBASE,GRADW_TEXBASE"
|
|
line.long 0x10 "GRADW_BORDERCOLOR,GRADW_BORDERCOLOR"
|
|
wgroup.long 0x380++0x1F
|
|
line.long 0x00 "GRADW_INST0,GRADW_INST0"
|
|
bitfld.long 0x00 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x00 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x00 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x00 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x00 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x00 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x00 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x04 "GRADW_INST1,GRADW_INST1"
|
|
bitfld.long 0x04 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x04 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x04 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x04 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x04 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x04 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x04 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x08 "GRADW_INST2,GRADW_INST2"
|
|
bitfld.long 0x08 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x08 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x08 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x08 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x08 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x08 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x08 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x0C "GRADW_INST3,GRADW_INST3"
|
|
bitfld.long 0x0C 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x0C 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x0C 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x0C 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x0C 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x0C 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x0C 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x10 "GRADW_INST4,GRADW_INST4"
|
|
bitfld.long 0x10 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x10 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x10 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x10 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x10 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x10 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x10 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x14 "GRADW_INST5,GRADW_INST5"
|
|
bitfld.long 0x14 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x14 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x14 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x14 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x14 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x14 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x14 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x18 "GRADW_INST6,GRADW_INST6"
|
|
bitfld.long 0x18 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x18 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x18 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x18 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x18 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x18 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x18 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
line.long 0x1C "GRADW_INST7,GRADW_INST7"
|
|
bitfld.long 0x1C 29.--30. " OPCODE ,Opcode" "DOT,RCP,SQRTMUL,SQRTADD"
|
|
bitfld.long 0x1C 25.--28. " DST ,Destination" "0000,0001,0010,0011,0100,0101,0110,0111,1000,1001,1010,1011,1100,1101,1110,1111"
|
|
textline " "
|
|
bitfld.long 0x1C 20.--24. " SRC_A ,Source A" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x1C 15.--19. " SRC_B ,Source B" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x1C 10.--14. " SRC_C ,Source C" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
bitfld.long 0x1C 5.--9. " SRC_D ,Source D" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
textline " "
|
|
bitfld.long 0x1C 0.--4. " SRC_E ,Source E" "00000,00001,00010,00011,00100,00101,00110,00111,01000,01001,01010,01011,01100,01101,01110,01111,10000,10001,10010,10011,10100,10101,10110,10111,11000,11001,11010,11011,11100,11101,11110,11111"
|
|
wgroup.long 0x3C0++0x13
|
|
line.long 0x00 "G2D_XY,G2D_XY"
|
|
hexmask.long.word 0x00 16.--27. 1. " X ,Primitive X"
|
|
bitfld.long 0x00 12.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x00 0.--11. 1. " Y ,Primitive Y"
|
|
line.long 0x04 "G2D_WIDTHHEIGHT,G2D_WIDTHHEIGHT"
|
|
hexmask.long.word 0x04 16.--27. 1. " WIDTH ,Primitive width"
|
|
bitfld.long 0x04 12.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x04 0.--11. 1. " HEIGHT ,Primitive height"
|
|
line.long 0x08 "G2D_SXY,G2D_SXY"
|
|
hexmask.long.word 0x08 16.--26. 1. " X ,Primitive source X"
|
|
bitfld.long 0x08 11.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
hexmask.long.word 0x08 0.--10. 1. " Y ,Primitive source Y"
|
|
line.long 0x0C "G2D_SXY2,G2D_SXY2"
|
|
hexmask.long.word 0x0C 16.--26. 1. " X ,Primitive source X"
|
|
bitfld.long 0x0C 11.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31"
|
|
textline " "
|
|
hexmask.long.word 0x0C 0.--10. 1. " Y ,Primitive source Y"
|
|
line.long 0x10 "G2D_VGSPAN,G2D_VGSPAN"
|
|
bitfld.long 0x10 16.--19. " COVERAGE ,Coverage value" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x10 12.--15. " PAD ,Padding" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
textline " "
|
|
hexmask.long.word 0x10 0.--11. 1. " WIDTH ,Span width"
|
|
wgroup.long 0x3F8++0x07
|
|
line.long 0x00 "G2D_IDLE,G2D_IDLE"
|
|
bitfld.long 0x00 2. " V3 ,Send signal to V3 after flush" "0,1"
|
|
bitfld.long 0x00 1. " BCFLUSH ,Flush burst cache" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 0. " IRQ ,Send IRQ after flush" "0,1"
|
|
line.long 0x04 "G2D_COLOR,G2D_COLOR"
|
|
tree.end
|
|
base ad:((per.l(ad:0x20000000+0xFF0))&0xffffffff)
|
|
tree "MMU Command Stream Registers"
|
|
group.long 0x100++0x0B
|
|
line.long 0x00 "MH_MMU_CONFIG,MH_MMU_CONFIG"
|
|
bitfld.long 0x00 24.--25. " PA_W_CLNT_BEHAVIOR ,Specifies PAw client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 22.--23. " TC_R_CLNT_BEHAVIOR ,Specifies TCr client behavior for MMU lookups" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 20.--21. " VGT_R1_CLNT_BEHAVIOR ,Specifies VGTr1 client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 18.--19. " VGT_R0_CLNT_BEHAVIOR ,Specifies VGTr0 client behavior for MMU lookups" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 16.--17. " CP_R4_CLNT_BEHAVIOR ,Specifies CPr4 client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 14.--15. " CP_R3_CLNT_BEHAVIOR ,Specifies CPr3 client behavior for MMU lookups" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 12.--13. " CP_R2_CLNT_BEHAVIOR ,Specifies CPr2 client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 10.--11. " CP_R1_CLNT_BEHAVIOR ,Specifies CPr1 client behavior for MMU lookups" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 8.--9. " CP_R0_CLNT_BEHAVIOR ,Specifies CPr0 client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 6.--7. " CP_W_CLNT_BEHAVIOR ,Specifies CPw client behavior for MMU lookups" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 4.--5. " RB_W_CLNT_BEHAVIOR ,Specifies RBw client behavior for MMU lookups" "0,1,2,3"
|
|
bitfld.long 0x00 2.--3. " PAD ,Padding" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 1. " SPLIT_MODE_ENABLE ,Reserves 8 translation buffer entries for use by the TC client" "Disabled,Enabled"
|
|
bitfld.long 0x00 0. " MMU_ENABLE ,Enables MMU" "Disabled,Enabled"
|
|
line.long 0x04 "MH_MMU_VA_RANGE,MH_MMU_VA_RANGE"
|
|
hexmask.long 0x04 12.--31. 1. " VA_BASE ,Virtual Base address (VA_BASE[31:12]) aligned to a 4kB page boundary (VA_BASE[11:0]=0)"
|
|
hexmask.long.word 0x04 0.--11. 1. " NUM_64KB_REGIONS ,Number of 64 KB regions mapped, up to 256MB"
|
|
line.long 0x08 "MH_MMU_PT_BASE,MH_MMU_PT_BASE"
|
|
hexmask.long 0x08 12.--31. 1. " PT_BASE ,Page Table Base address (PT_BASE[31:12]) aligned to a 4kB page boundary (PT_BASE[11:0]=0)"
|
|
hexmask.long.word 0x08 0.--11. 1. " ZERO,Alignment ,Alignment, zeroed"
|
|
rgroup.long 0x10C++0x03
|
|
line.long 0x00 "MH_MMU_PAGE_FAULT,MH_MMU_PAGE_FAULT"
|
|
hexmask.long.tbyte 0x00 12.--31. 1. " REQ_VA ,VA[31:12] of lookup that caused the page fault"
|
|
bitfld.long 0x00 11. " WRITE_PROTECTION_ERROR ,Page table entry not valid for write operation" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 10. " READ_PROTECTION_ERROR ,Page table entry not valid for read operation" "0,1"
|
|
bitfld.long 0x00 9. " ADDRESS_OUT_OF_RANGE ,Client VA not in VA range" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 8. " MPU_ADDRESS_OUT_OF_RANGE ,Client PA not in MPU range" "0,1"
|
|
bitfld.long 0x00 7. " PAD ,Padding bit" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 4.--6. " AXI_ID ,AXI ID" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x00 2.--3. " CLNT_BEHAVIOR ,Client behavior" "0,1,2,3"
|
|
textline " "
|
|
bitfld.long 0x00 1. " OP_TYPE ,Operation Type" "0,1"
|
|
bitfld.long 0x00 0. " PAGE_FAULT ,Page fault occured" "Not occurred,Occurred"
|
|
group.long 0x110++0x0F
|
|
line.long 0x00 "MH_MMU_TRAN_ERROR,MH_MMU_TRAN_ERROR"
|
|
hexmask.long 0x00 5.--31. 1. " TRAN_ERROR ,Address location used for dummy reads or writes in the event of a page fault"
|
|
hexmask.long.byte 0x00 0.--4. 1. " ZERO,Alignment ,Alignment, zeroed"
|
|
line.long 0x04 "MH_MMU_INVALIDATE,MH_MMU_INVALIDATE"
|
|
bitfld.long 0x04 1. " INVALIDATE_TC ,INVALIDATE_TC" "Not in progress,In progress"
|
|
bitfld.long 0x04 0. " INVALIDATE_ALL ,INVALIDATE_ALL" "Not in progress,In progress"
|
|
line.long 0x08 "MH_MMU_MPU_BASE,MH_MMU_MPU_BASE"
|
|
hexmask.long 0x08 12.--31. 1. " MPU_BASE ,Memory Protection Unit Base address aligned to a 4kB page boundary"
|
|
hexmask.long.word 0x08 0.--11. 1. " ZERO,Alignment ,Alignment, zeroed"
|
|
line.long 0x0C "MH_MMU_MPU_END,MH_MMU_MPU_END"
|
|
hexmask.long 0x0C 12.--31. 1. " MPU_END ,Memory Protection Unit End address aligned to a 4kB page boundary"
|
|
hexmask.long.word 0x0C 0.--11. 1. " ZERO,Alignment ,Alignment, zeroed"
|
|
group.long 0x2900++0x13
|
|
line.long 0x00 "MH_ARBITER_CONFIG,MH_ARBITER_CONFIG"
|
|
bitfld.long 0x00 26. " PA_CLNT_ENABLE ,Enables PA client requests" "Disabled,Enabled"
|
|
bitfld.long 0x00 25. " RB_CLNT_ENABLE ,Enables RB client requests" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 24. " TC_CLNT_ENABLE ,Enables TC client requests" "Disabled,Enabled"
|
|
bitfld.long 0x00 23. " VGT_CLNT_ENABLE ,Enables VGT client requests" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 22. " CP_CLNT_ENABLE ,Enables CP client requests" "Disabled,Enabled"
|
|
bitfld.long 0x00 16.--21. " IN_FLIGHT_LIMIT ,Maximum number of outstanding requests allowed by MH" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
textline " "
|
|
bitfld.long 0x00 15. " IN_FLIGHT_LIMIT_ENABLE ,Enables limit of outstanding requests" "0,1"
|
|
bitfld.long 0x00 14. " TC_ARB_HOLD_ENABLE ,Holds arbiter for 4 cycles enable bit" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x00 13. " TC_REORDER_ENABLE ,Enables TC reordering queue" "Disabled,Enabled"
|
|
bitfld.long 0x00 10.--12. " PAGE_SIZE ,SDRAM page size--RBC or BRC formats assumed for SDRAM configuration" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 9. " L2_ARB_CONTROL ,Selects algorithm for level 2 arbitration" "0,1"
|
|
bitfld.long 0x00 8. " L1_ARB_HOLD_ENABLE ,Selects behavior when arbiter is back pressured" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 7. " L1_ARB_ENABLE ,Enables level 1 arbitration for same page and bank addresses" "Disabled,Enabled"
|
|
bitfld.long 0x00 6. " SAME_PAGE_GRANULARITY ,Granularity of SAME_PAGE_LIMIT" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 0.--5. " SAME_PAGE_LIMIT ,Number of same page requests allowed before re-arbitration" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63"
|
|
line.long 0x04 "MH_CLNT_AXI_ID_REUSE,MH_CLNT_AXI_ID_REUSE"
|
|
bitfld.long 0x04 12.--14. " PAW_ID ,PA write client AXI ID" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x04 11. " PAD3 ,Padding bit" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 8.--10. " MMUR_ID ,MMU read client AXI ID" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x04 7. " PAD2 ,Padding bit" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 4.--6. " RBW_ID ,RB write client AXI ID" "0,1,2,3,4,5,6,7"
|
|
bitfld.long 0x04 3. " PAD ,Padding bit" "0,1"
|
|
textline " "
|
|
bitfld.long 0x04 0.--2. " CPW_ID ,CP write sub-client AXI ID" "0,1,2,3,4,5,6,7"
|
|
line.long 0x08 "MH_INTERRUPT_MASK,MH_INTERRUPT_MASK"
|
|
bitfld.long 0x08 2. " MMU_PAGE_FAULT ,Enables MMU page fault interrupt" "Disabled,Enabled"
|
|
bitfld.long 0x08 1. " AXI_WRITE_ERROR ,Enables AXI Write error interrupt" "Disabled,Enabled"
|
|
textline " "
|
|
bitfld.long 0x08 0. " AXI_READ_ERROR ,Enables AXI Read error interrupt" "Disabled,Enabled"
|
|
line.long 0x0C "MH_INTERRUPT_STATUS,MH_INTERRUPT_STATUS"
|
|
bitfld.long 0x0C 2. " MMU_PAGE_FAULT ,MMU page fault interrupt status" "No interrupt,Interrupt"
|
|
bitfld.long 0x0C 1. " AXI_WRITE_ERROR ,AXI Write error interrupt status" "No interrupt,Interrupt"
|
|
textline " "
|
|
bitfld.long 0x0C 0. " AXI_READ_ERROR ,AXI Read error interrupt status" "No interrupt,Interrupt"
|
|
line.long 0x10 "MH_INTERRUPT_CLEAR,MH_INTERRUPT_CLEAR"
|
|
bitfld.long 0x10 2. " MMU_PAGE_FAULT ,Clear MMU page fault interrupt" "0,1"
|
|
bitfld.long 0x10 1. " AXI_WRITE_ERROR ,Clear AXI Write error interrupt" "0,1"
|
|
textline " "
|
|
bitfld.long 0x10 0. " AXI_READ_ERROR ,Clear AXI Read error interrupt" "0,1"
|
|
rgroup.long 0x2914++0x03
|
|
line.long 0x00 "MH_AXI_ERROR,MH_AXI_ERROR"
|
|
bitfld.long 0x00 7. " AXI_WRITE_ERROR ,AXI Write error" "No error,Error"
|
|
bitfld.long 0x00 4.--6. " AXI_WRITE_ID ,AXI ID of write error" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 3. " AXI_READ_ERROR ,AXI Read error" "No error,Error"
|
|
bitfld.long 0x00 0.--2. " AXI_READ_ID ,AXI ID of read error" "0,1,2,3,4,5,6,7"
|
|
group.long 0x2918++0x07
|
|
line.long 0x00 "MH_PERFCOUNTER0_SELECT,MH_PERFCOUNTER0_SELECT"
|
|
hexmask.long.byte 0x00 0.--7. 1. " PERF_SEL ,Counter Select"
|
|
line.long 0x04 "MH_PERFCOUNTER0_CONFIG,MH_PERFCOUNTER0_CONFIG"
|
|
hexmask.long.byte 0x04 0.--7. 1. " N_VALUE ,N value used in Nth access and N entry measurements only"
|
|
rgroup.long 0x2920++0x07
|
|
line.long 0x00 "MH_PERFCOUNTER0_LOW,MH_PERFCOUNTER0_LOW"
|
|
line.long 0x04 "MH_PERFCOUNTER0_HI,MH_PERFCOUNTER0_HI"
|
|
hexmask.long.word 0x04 0.--15. 1. " PERF_COUNTER_HI ,Upper 16 bits of performance count"
|
|
group.long 0x2928++0x07
|
|
line.long 0x00 "MH_PERFCOUNTER1_SELECT,MH_PERFCOUNTER1_SELECT"
|
|
hexmask.long.byte 0x00 0.--7. 1. " PERF_SEL ,Counter Select"
|
|
line.long 0x04 "MH_PERFCOUNTER1_CONFIG,MH_PERFCOUNTER1_CONFIG"
|
|
hexmask.long.byte 0x04 0.--7. 1. " N_VALUE ,N value used in Nth access and N entry measurements only"
|
|
rgroup.long 0x2930++0x07
|
|
line.long 0x00 "MH_PERFCOUNTER1_LOW,MH_PERFCOUNTER1_LOW"
|
|
line.long 0x04 "MH_PERFCOUNTER1_HI,MH_PERFCOUNTER1_HI"
|
|
hexmask.long.word 0x04 0.--15. 1. " PERF_COUNTER_HI ,Upper 16 bits of performance count"
|
|
group.long 0x2938++0x03
|
|
line.long 0x00 "MH_DEBUG_CTRL,MH_DEBUG_CTRL"
|
|
hexmask.long.byte 0x00 0.--5. 1. " INDEX ,Debug data index"
|
|
rgroup.long 0x293C++0x03
|
|
line.long 0x00 "MH_DEBUG_DATA,MH_DEBUG_DATA"
|
|
group.long 0x2940++0x03
|
|
line.long 0x00 "MH_AXI_HALT_CONTROL,MH_AXI_HALT_CONTROL"
|
|
bitfld.long 0x00 0. " AXI_HALT ,AXI Halt" "Not acknowledged,Acknowledged"
|
|
tree.end
|
|
width 0xB
|
|
tree.end
|
|
textline " "
|