838 lines
49 KiB
Plaintext
838 lines
49 KiB
Plaintext
; --------------------------------------------------------------------------------
|
|
; @Title: Cortex-M0+ On-Chip Peripherals
|
|
; @Props: Released
|
|
; @Author: WWI, SIK, KRZ
|
|
; @Changelog: 2016-03-22 WWI
|
|
; 2017-08-08 SIK
|
|
; 2022-11-17 KRZ
|
|
; @Manufacturer: ARM - ARM Ltd.
|
|
; @Doc: DDI0484C_cortex_m0p_r0p1_trm.pdf
|
|
; DDI0419C_arm_architecture_v6m_reference_manual.pdf
|
|
; @Core: Cortex-M0+
|
|
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
|
|
; --------------------------------------------------------------------------------
|
|
; $Id: percortexm0p.per 15448 2022-11-17 13:10:57Z kwisniewski $
|
|
|
|
config 16. 8.
|
|
ASSERT VERSION.BUILD.BASE()>=80109.
|
|
|
|
sif PER.isNOTIFICATION()
|
|
base AVM:0x00000000
|
|
wgroup AVM:0x00++0
|
|
textline " Peripheral File Notification - "
|
|
button "show missing files" "DIALOG.MESSAGE ""Please check your installation for the possibly missing files:""+CONV.CHAR(0xa)+PER.NOTIFICATION.MISSINGFILES()"
|
|
textline " ---------------------------------------------------------------"
|
|
textline " The peripheral file for this SoC cannot be displayed. "
|
|
textline " Possible reasons are: "
|
|
textline " - it is missing in the local installation or under development "
|
|
textline " - it is confidential "
|
|
textline " "
|
|
textline " As fallback only the core registers are shown. "
|
|
textline " Please check www.lauterbach.com/scripts.html "
|
|
textline " or contact support@lauterbach.com . "
|
|
textline " "
|
|
endif
|
|
AUTOINDENT.PUSH
|
|
AUTOINDENT.OFF
|
|
tree "System Control"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 0x8
|
|
if (CORENAME()=="CORTEXM1")
|
|
group.long 0x10++0x0b
|
|
line.long 0x00 "STCSR,SysTick Control and Status Register"
|
|
bitfld.long 0x00 16. " COUNTFLAG ,Returns 1 if timer counted to 0" "0,1"
|
|
bitfld.long 0x00 2. " CLKSOURCE ,Always reads as one" "No effect,Processor clock"
|
|
textline " "
|
|
bitfld.long 0x00 1. " TICKINT ,Counting down to 0 " "No SysTick,SysTick"
|
|
bitfld.long 0x00 0. " ENABLE ,Counter enable" "Disabled,Enabled"
|
|
line.long 0x04 "STRVR,SysTick Reload Value Register"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,Value to load into the STCVR when the counter reaches 0"
|
|
line.long 0x08 "STCVR,SysTick Current Value Register"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " CURRENT ,Reads return the current value of the SysTick counter"
|
|
else
|
|
group.long 0x10++0x0b
|
|
line.long 0x00 "STCSR,SysTick Control and Status Register"
|
|
bitfld.long 0x00 16. " COUNTFLAG ,Returns 1 if timer counted to 0" "0,1"
|
|
bitfld.long 0x00 2. " CLKSOURCE ,Always reads as one" "External clock,Processor clock"
|
|
textline " "
|
|
bitfld.long 0x00 1. " TICKINT ,Counting down to 0 " "No SysTick,SysTick"
|
|
bitfld.long 0x00 0. " ENABLE ,Counter enable" "Disabled,Enabled"
|
|
line.long 0x04 "STRVR,SysTick Reload Value Register"
|
|
hexmask.long.tbyte 0x04 0.--23. 1. " RELOAD ,Value to load into the STCVR when the counter reaches 0"
|
|
line.long 0x08 "STCVR,SysTick Current Value Register"
|
|
hexmask.long.tbyte 0x08 0.--23. 1. " CURRENT ,Reads return the current value of the SysTick counter"
|
|
endif
|
|
if (CORENAME()=="CORTEXM1")
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "STCR,SysTick Calibration Value Register"
|
|
bitfld.long 0x00 31. " NOREF ,Reads as one" "0,1"
|
|
bitfld.long 0x00 30. " SKEW ,Reads as zero" "0,1"
|
|
textline " "
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Indicates calibration value is not known"
|
|
else
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "STCR,SysTick Calibration Value Register"
|
|
bitfld.long 0x00 31. " NOREF ,Indicates whether the IMPL_DEF reference clock is provided" "Implemented,Not implemented"
|
|
bitfld.long 0x00 30. " SKEW ,Indicates whether the 10ms calibration value is exact" "Exact,Inexact"
|
|
textline " "
|
|
hexmask.long.tbyte 0x00 0.--23. 1. " TENMS ,Holds a reload value to be used for 10ms (100Hz) timing subject to system clock skew errors"
|
|
endif
|
|
rgroup.long 0xd00++0x03
|
|
line.long 0x00 "CPUID,CPU ID Base Register"
|
|
hexmask.long.byte 0x00 24.--31. 1. " IMPLEMENTER ,Implementer code"
|
|
hexmask.long.byte 0x00 20.--23. 1. " VARIANT ,Implementation defined variant number"
|
|
textline " "
|
|
hexmask.long.byte 0x00 4.--15. 1. " PARTNO ,Number of processor within family"
|
|
hexmask.long.byte 0x00 0.--3. 1. " REVISION ,Implementation defined revision number"
|
|
group.long 0xd04++0x03
|
|
line.long 0x00 "ICSR,Interrupt Control State Register"
|
|
bitfld.long 0x00 31. " NMIPENDSET ,Setting this bit will activate an NMI" "No effect,Set pending"
|
|
bitfld.long 0x00 28. " PENDSVSET ,Set a pending PendSV interrupt" "No effect,Set pending"
|
|
textline " "
|
|
bitfld.long 0x00 27. " PENDSVCLR ,Clear a pending PendSV interrupt" "No effect,Clear pending"
|
|
bitfld.long 0x00 26. " PENDSTSET ,Set a pending SysTick" "No effect,Set pending"
|
|
textline " "
|
|
bitfld.long 0x00 25. " PENDSVCLR ,Clear a pending SysTick" "No effect,Clear pending"
|
|
bitfld.long 0x00 23. " ISRPREEMPT ,Pending exception service" "No service,Service"
|
|
textline " "
|
|
bitfld.long 0x00 22. " ISRPENDING ,External interrupt pending flag" "No interrupt,Interrupt"
|
|
hexmask.long.byte 0x00 12.--17. 1. " VECTPENDING ,Active exception number field"
|
|
textline " "
|
|
hexmask.long.byte 0x00 0.--5. 1. " VECTACTIVET ,Active exception number field"
|
|
if (CORENAME()=="CORTEXM0+")
|
|
group.long 0xd08++0x03
|
|
line.long 0x00 "VTOR,Vector Table Offset Register"
|
|
hexmask.long 0x00 7.--31. 0x80 " TBLOFF ,Vector table address"
|
|
else
|
|
textline " "
|
|
endif
|
|
group.long 0xd0c++0x03
|
|
line.long 0x00 "AIRCR,Application Interrupt and Reset Control Register"
|
|
hexmask.long.word 0x00 16.--31. 1. " VECTKEY ,Vector Key"
|
|
bitfld.long 0x00 15. " ENDIANNESS ,Data endianness bit" "Little-endian,Big-endian"
|
|
textline " "
|
|
bitfld.long 0x00 2. " SYSRESETREQ ,System reset setup request" "No effect,Reset"
|
|
bitfld.long 0x00 1. " VECTCLRACTIVE ,Clears all active state information" "No clear,Clear"
|
|
group.long 0xd10++0x03
|
|
line.long 0x00 "SCR,System Control Register"
|
|
bitfld.long 0x00 4. " SEVONPEND ,Determines whether an interrupt transition from inactive state to pending state is a wakeup event" "Not wakeup,Wakeup"
|
|
bitfld.long 0x00 2. " SLEEPDEEP ,Provides a qualifying hint indicating that waking from sleep might take longer" "Not deep sleep,Deep sleep"
|
|
textline " "
|
|
bitfld.long 0x00 1. " SLEEPONEXIT ,Determines whether, on an exit from an ISR that returns to the base level of execution priority, the processor enters a sleep state" "Disabled,Enabled"
|
|
rgroup.long 0xd14++0x03
|
|
line.long 0x00 "CCR,Configuration and Control Register"
|
|
bitfld.long 0x00 9. " STKALIGN ,Indicates whether on exception entry all exceptions are entered with 8-byte stack alignment and the context to restore it is saved" "Reserved,Aligned"
|
|
bitfld.long 0x00 3. " UNALIGN_TRP ,Indicates that all unaligned accesses results in a Hard Fault" "Reserved,Trapped"
|
|
group.long 0xd1c++0x0b
|
|
line.long 0x00 "SHPR2,System Handler Priority Register 2"
|
|
bitfld.long 0x00 30.--31. " PRI_11 ,Priority of system handler 11-SVCall" "00,01,10,11"
|
|
line.long 0x04 "SHPR3,System Handler Priority Register 3"
|
|
bitfld.long 0x04 30.--31. " PRI_15 ,Priority of system handler 15-SysTick" "00,01,10,11"
|
|
bitfld.long 0x04 22.--23. " PRI_14 ,Priority of system handler 14- PendSV" "00,01,10,11"
|
|
line.long 0x08 "SHCSR,System Handler Control and State Register"
|
|
bitfld.long 0x08 15. " SVCALLPENDED ,Reads as 1 if SVCall is pending" "Not pending,Pending"
|
|
if (CORENAME()=="CORTEXM0+")
|
|
hgroup.long 0x08++0x03
|
|
hide.long 0x00 "ACTLR,Auxiliary Control Register"
|
|
else
|
|
textline " "
|
|
endif
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Memory Protection Unit (MPU)"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 15.
|
|
rgroup.long 0xD90++0x03
|
|
line.long 0x00 "MPU_TYPE,MPU Type Register"
|
|
bitfld.long 0x00 8.--15. 1. " DREGION ,Number of regions supported by the MPU" "0,1,2,3,4,5,6,7,8,?..."
|
|
group.long 0xD94++0x03
|
|
line.long 0x00 "MPU_CTRL,MPU Control Register"
|
|
bitfld.long 0x00 2. " PRIVDEFENA ,Enables the default memory map as a background region for privileged access" "Disabled,Enabled"
|
|
bitfld.long 0x00 1. " HFNMIENA ,Handlers executing with priority less than 0 access memory with the MPU enabled or with the MPU disabled" "MPU disabled,MPU enabled"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables the MPU" "Disabled,Enabled"
|
|
group.long 0xD98++0x03
|
|
line.long 0x00 "MPU_RNR,MPU Region Number Register"
|
|
hexmask.long.byte 0x00 0.--7. 1. " REGION ,Indicates the memory region accessed by MPU_RBAR and MPU_RASR"
|
|
tree.close "MPU regions"
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x0
|
|
group.long 0xD9C++0x03 "Region 0"
|
|
saveout 0xD98 %l 0x0
|
|
line.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x0
|
|
line.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 0 (not implemented)"
|
|
saveout 0xD98 %l 0x0
|
|
hide.long 0x00 "MPU_RBAR0,MPU Region Base Address Register 0"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x0
|
|
hide.long 0x00 "MPU_RASR0,MPU Region Attribute and Size Register 0"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x1
|
|
group.long 0xD9C++0x03 "Region 1"
|
|
saveout 0xD98 %l 0x1
|
|
line.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x1
|
|
line.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 1 (not implemented)"
|
|
saveout 0xD98 %l 0x1
|
|
hide.long 0x00 "MPU_RBAR1,MPU Region Base Address Register 1"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x1
|
|
hide.long 0x00 "MPU_RASR1,MPU Region Attribute and Size Register 1"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x2
|
|
group.long 0xD9C++0x03 "Region 2"
|
|
saveout 0xD98 %l 0x2
|
|
line.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x2
|
|
line.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 2 (not implemented)"
|
|
saveout 0xD98 %l 0x2
|
|
hide.long 0x00 "MPU_RBAR2,MPU Region Base Address Register 2"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x2
|
|
hide.long 0x00 "MPU_RASR2,MPU Region Attribute and Size Register 2"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x3
|
|
group.long 0xD9C++0x03 "Region 3"
|
|
saveout 0xD98 %l 0x3
|
|
line.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x3
|
|
line.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 3 (not implemented)"
|
|
saveout 0xD98 %l 0x3
|
|
hide.long 0x00 "MPU_RBAR3,MPU Region Base Address Register 3"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x3
|
|
hide.long 0x00 "MPU_RASR3,MPU Region Attribute and Size Register 3"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x4
|
|
group.long 0xD9C++0x03 "Region 4"
|
|
saveout 0xD98 %l 0x4
|
|
line.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x4
|
|
line.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 4 (not implemented)"
|
|
saveout 0xD98 %l 0x4
|
|
hide.long 0x00 "MPU_RBAR4,MPU Region Base Address Register 4"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x4
|
|
hide.long 0x00 "MPU_RASR4,MPU Region Attribute and Size Register 4"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x5
|
|
group.long 0xD9C++0x03 "Region 5"
|
|
saveout 0xD98 %l 0x5
|
|
line.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x5
|
|
line.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 5 (not implemented)"
|
|
saveout 0xD98 %l 0x5
|
|
hide.long 0x00 "MPU_RBAR5,MPU Region Base Address Register 5"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x5
|
|
hide.long 0x00 "MPU_RASR5,MPU Region Attribute and Size Register 5"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x6
|
|
group.long 0xD9C++0x03 "Region 6"
|
|
saveout 0xD98 %l 0x6
|
|
line.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x6
|
|
line.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 6 (not implemented)"
|
|
saveout 0xD98 %l 0x6
|
|
hide.long 0x00 "MPU_RBAR6,MPU Region Base Address Register 6"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x6
|
|
hide.long 0x00 "MPU_RASR6,MPU Region Attribute and Size Register 6"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
if ((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xD90)&0xff00)>>8)>0x7
|
|
group.long 0xD9C++0x03 "Region 7"
|
|
saveout 0xD98 %l 0x7
|
|
line.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7"
|
|
hexmask.long 0x00 8.--31. 0x20 " ADDR ,Base address of the region"
|
|
group.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x7
|
|
line.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7"
|
|
bitfld.long 0x00 28. " XN ,eXecute Never" "Execute,Not execute"
|
|
bitfld.long 0x00 24.--26. " AP ,Data Access Permission" "No access,S:RW U:--,S:RW U:R-,S:RW U:RR,reserved,S:R- U:--,S:R- U:R-,S:R- U:R-"
|
|
bitfld.long 0x00 19.--21. " TEX ,Type Extension Field" "0,1,2,3,4,5,6,7"
|
|
textline " "
|
|
bitfld.long 0x00 18. " S ,Shareable Bit" "Not shareable,Shareable"
|
|
bitfld.long 0x00 17. " C ,Cacheable Bit" "Not cacheable,Cacheable"
|
|
bitfld.long 0x00 16. " B ,Bufferable Bit" "Not bufferable,Bufferable"
|
|
textline " "
|
|
bitfld.long 0x00 15. " SRD[7..0] ,Subregion 7 Disable" "0,1"
|
|
bitfld.long 0x00 14. ",Subregion 6 Disable" "0,1"
|
|
bitfld.long 0x00 13. ",Subregion 5 Disable" "0,1"
|
|
bitfld.long 0x00 12. ",Subregion 4 Disable" "0,1"
|
|
bitfld.long 0x00 11. ",Subregion 3 Disable" "0,1"
|
|
bitfld.long 0x00 10. ",Subregion 2 Disable" "0,1"
|
|
bitfld.long 0x00 9. ",Subregion 1 Disabled" "0,1"
|
|
bitfld.long 0x00 8. ",Subregion 0 Disable" "0,1"
|
|
bitfld.long 0x00 1.--5. " SIZE ,Indicates the region size" "-,-,-,-,-,-,-,256 B,512 B,1 kB,2 kB,4 kB,8 kB,16 kB,32 kB,64 kB,128 kB,256 kB,512 kB,1 MB,2 MB,4 MB,8 MB,16 MB,32 MB,64 MB,128 MB,256 MB,512 MB,1 GB,2 GB,4 GB"
|
|
bitfld.long 0x00 0. " ENABLE ,Enables this region" "Disabled,Enabled"
|
|
else
|
|
hgroup.long 0xD9C++0x03 "Region 7 (not implemented)"
|
|
saveout 0xD98 %l 0x7
|
|
hide.long 0x00 "MPU_RBAR7,MPU Region Base Address Register 7"
|
|
hgroup.long 0xDA0++0x03
|
|
saveout 0xD98 %l 0x7
|
|
hide.long 0x00 "MPU_RASR7,MPU Region Attribute and Size Register 7"
|
|
textline " "
|
|
textline " "
|
|
endif
|
|
tree.end
|
|
width 0x0b
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Nested Vectored Interrupt Controller (NVIC)"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 12.
|
|
tree "Interrupt Enable Registers"
|
|
group.long 0x100++0x03
|
|
line.long 0x00 "SET/CLREN,Interrupt Set/Clear Enable Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " SET/CLRENA31 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " SET/CLRENA30 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " SET/CLRENA29 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " SET/CLRENA28 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " SET/CLRENA27 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " SET/CLRENA26 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " SET/CLRENA25 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " SET/CLRENA24 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " SET/CLRENA23 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " SET/CLRENA22 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " SET/CLRENA21 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " SET/CLRENA20 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " SET/CLRENA19 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " SET/CLRENA18 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " SET/CLRENA17 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " SET/CLRENA16 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " SET/CLRENA15 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " SET/CLRENA14 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " SET/CLRENA13 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " SET/CLRENA12 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " SET/CLRENA11 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " SET/CLRENA10 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " SET/CLRENA9 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " SET/CLRENA8 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " SET/CLRENA7 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " SET/CLRENA6 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " SET/CLRENA5 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " SET/CLRENA4 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " SET/CLRENA3 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " SET/CLRENA2 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " SET/CLRENA1 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " SET/CLRENA0 ,Interrupt Set/Clear Enable Bit" "Disabled,Enabled"
|
|
tree.end
|
|
tree "Interrupt Pending Registers"
|
|
group.long 0x200++0x03
|
|
line.long 0x00 "SET/CLRPEN,Interrupt Set/Clear Pending Register"
|
|
setclrfld.long 0x00 31. 0x00 31. 0x80 31. " SET/CLRPEN31 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 30. 0x00 30. 0x80 30. " SET/CLRPEN30 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 29. 0x00 29. 0x80 29. " SET/CLRPEN29 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 28. 0x00 28. 0x80 28. " SET/CLRPEN28 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 27. 0x00 27. 0x80 27. " SET/CLRPEN27 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 26. 0x00 26. 0x80 26. " SET/CLRPEN26 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 25. 0x00 25. 0x80 25. " SET/CLRPEN25 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 24. 0x00 24. 0x80 24. " SET/CLRPEN24 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 23. 0x00 23. 0x80 23. " SET/CLRPEN23 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 22. 0x00 22. 0x80 22. " SET/CLRPEN22 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 21. 0x00 21. 0x80 21. " SET/CLRPEN21 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 20. 0x00 20. 0x80 20. " SET/CLRPEN20 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 19. 0x00 19. 0x80 19. " SET/CLRPEN19 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 18. 0x00 18. 0x80 18. " SET/CLRPEN18 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 17. 0x00 17. 0x80 17. " SET/CLRPEN17 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 16. 0x00 16. 0x80 16. " SET/CLRPEN16 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 15. 0x00 15. 0x80 15. " SET/CLRPEN15 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 14. 0x00 14. 0x80 14. " SET/CLRPEN14 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 13. 0x00 13. 0x80 13. " SET/CLRPEN13 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 12. 0x00 12. 0x80 12. " SET/CLRPEN12 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 11. 0x00 11. 0x80 11. " SET/CLRPEN11 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 10. 0x00 10. 0x80 10. " SET/CLRPEN10 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 9. 0x00 9. 0x80 9. " SET/CLRPEN9 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 8. 0x00 8. 0x80 8. " SET/CLRPEN8 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 7. 0x00 7. 0x80 7. " SET/CLRPEN7 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 6. 0x00 6. 0x80 6. " SET/CLRPEN6 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 5. 0x00 5. 0x80 5. " SET/CLRPEN5 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 4. 0x00 4. 0x80 4. " SET/CLRPEN4 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 3. 0x00 3. 0x80 3. " SET/CLRPEN3 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 2. 0x00 2. 0x80 2. " SET/CLRPEN2 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
textline " "
|
|
setclrfld.long 0x00 1. 0x00 1. 0x80 1. " SET/CLRPEN1 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
setclrfld.long 0x00 0. 0x00 0. 0x80 0. " SET/CLRPEN0 ,Interrupt Set/Clear Pending" "Not pending,Pending"
|
|
tree.end
|
|
width 6.
|
|
tree "Interrupt Priority Registers"
|
|
group.long 0x400++0x1F
|
|
line.long 0x00 "INT0,Interrupt Priority Register"
|
|
bitfld.long 0x00 30.--31. " IP_3 ,Priority of interrupt 3" "0,1,2,3"
|
|
bitfld.long 0x00 22.--23. " IP_2 ,Priority of interrupt 2" "0,1,2,3"
|
|
bitfld.long 0x00 14.--15. " IP_1 ,Priority of interrupt 1" "0,1,2,3"
|
|
bitfld.long 0x00 6.--7. " IP_0 ,Priority of interrupt 0" "0,1,2,3"
|
|
line.long 0x04 "INT1,Interrupt Priority Register"
|
|
bitfld.long 0x04 30.--31. " IP_7 ,Priority of interrupt 7" "0,1,2,3"
|
|
bitfld.long 0x04 22.--23. " IP_6 ,Priority of interrupt 6" "0,1,2,3"
|
|
bitfld.long 0x04 14.--15. " IP_5 ,Priority of interrupt 5" "0,1,2,3"
|
|
bitfld.long 0x04 6.--7. " IP_4 ,Priority of interrupt 4" "0,1,2,3"
|
|
line.long 0x08 "INT2,Interrupt Priority Register"
|
|
bitfld.long 0x08 30.--31. " IP_11 ,Priority of interrupt 11" "0,1,2,3"
|
|
bitfld.long 0x08 22.--23. " IP_10 ,Priority of interrupt 10" "0,1,2,3"
|
|
bitfld.long 0x08 14.--15. " IP_9 ,Priority of interrupt 9" "0,1,2,3"
|
|
bitfld.long 0x08 6.--7. " IP_8 ,Priority of interrupt 8" "0,1,2,3"
|
|
line.long 0x0C "INT3,Interrupt Priority Register"
|
|
bitfld.long 0x0C 30.--31. " IP_15 ,Priority of interrupt 15" "0,1,2,3"
|
|
bitfld.long 0x0C 22.--23. " IP_14 ,Priority of interrupt 14" "0,1,2,3"
|
|
bitfld.long 0x0C 14.--15. " IP_13 ,Priority of interrupt 13" "0,1,2,3"
|
|
bitfld.long 0x0C 6.--7. " IP_12 ,Priority of interrupt 12" "0,1,2,3"
|
|
line.long 0x10 "INT4,Interrupt Priority Register"
|
|
bitfld.long 0x10 30.--31. " IP_19 ,Priority of interrupt 19" "0,1,2,3"
|
|
bitfld.long 0x10 22.--23. " IP_18 ,Priority of interrupt 18" "0,1,2,3"
|
|
bitfld.long 0x10 14.--15. " IP_17 ,Priority of interrupt 17" "0,1,2,3"
|
|
bitfld.long 0x10 6.--7. " IP_16 ,Priority of interrupt 16" "0,1,2,3"
|
|
line.long 0x14 "INT5,Interrupt Priority Register"
|
|
bitfld.long 0x14 30.--31. " IP_23 ,Priority of interrupt 23" "0,1,2,3"
|
|
bitfld.long 0x14 22.--23. " IP_22 ,Priority of interrupt 22" "0,1,2,3"
|
|
bitfld.long 0x14 14.--15. " IP_21 ,Priority of interrupt 21" "0,1,2,3"
|
|
bitfld.long 0x14 6.--7. " IP_20 ,Priority of interrupt 20" "0,1,2,3"
|
|
line.long 0x18 "INT6,Interrupt Priority Register"
|
|
bitfld.long 0x18 30.--31. " IP_27 ,Priority of interrupt 27" "0,1,2,3"
|
|
bitfld.long 0x18 22.--23. " IP_26 ,Priority of interrupt 26" "0,1,2,3"
|
|
bitfld.long 0x18 14.--15. " IP_25 ,Priority of interrupt 25" "0,1,2,3"
|
|
bitfld.long 0x18 6.--7. " IP_24 ,Priority of interrupt 24" "0,1,2,3"
|
|
line.long 0x1C "INT7,Interrupt Priority Register"
|
|
bitfld.long 0x1C 30.--31. " IP_31 ,Priority of interrupt 31" "0,1,2,3"
|
|
bitfld.long 0x1C 22.--23. " IP_30 ,Priority of interrupt 30" "0,1,2,3"
|
|
bitfld.long 0x1C 14.--15. " IP_29 ,Priority of interrupt 29" "0,1,2,3"
|
|
bitfld.long 0x1C 6.--7. " IP_28 ,Priority of interrupt 28" "0,1,2,3"
|
|
tree.end
|
|
width 0x0B
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Debug"
|
|
tree "Core Debug"
|
|
sif COMPonent.AVAILABLE("COREDEBUG")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))
|
|
width 0xA
|
|
group.long 0xD30++0x03
|
|
line.long 0x00 "DFSR,Data Fault Status Register"
|
|
eventfld.long 0x00 4. " EXTERNAL ,External debug request flag" "No occurred,Occurred"
|
|
eventfld.long 0x00 3. " VCATCH ,Vector catch flag" "No occurred,Occurred"
|
|
textline " "
|
|
eventfld.long 0x00 2. " DWTRAP ,Data Watchpoint flag" "No match,Match"
|
|
textline " "
|
|
eventfld.long 0x00 1. " BKPT ,BKPT flag" "No match,Match"
|
|
eventfld.long 0x00 0. " HALTED ,Halt request flag" "No request,Request"
|
|
if (CORENAME()=="CORTEXM1")
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x01)==0x00)
|
|
group.long 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not completed,Completed"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 18. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
textline " "
|
|
textfld " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
else
|
|
group.long 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 18. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked"
|
|
bitfld.long 0x00 2. " C_STEP ,Steps the core in halted debug" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
endif
|
|
else
|
|
if (((per.l(CONvert.ADDRESSTODUALPORT(COMPonent.BASE("COREDEBUG",-1))+0xDF0))&0x01)==0x00)
|
|
group.long 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not completed,Completed"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core Lockup Status/Debug Key" "Not locked up,Locked up"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core Sleep Status/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
textline " "
|
|
textfld " "
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
else
|
|
group.long 0xDF0++0x03
|
|
line.long 0x00 "DHCSR,Debug Halting Control and Status Register"
|
|
bitfld.long 0x00 31. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 30. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 29. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 28. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 27. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 26. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 25. " S_RESET_ST/DBGKEY ,Core Reset/Debug Key" "No reset,Reset"
|
|
bitfld.long 0x00 24. " S_RETIRE_ST/DBGKEY ,Instruction completed since last read/Debug Key" "Not read,Read"
|
|
textline " "
|
|
bitfld.long 0x00 23. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 22. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 21. " DBGKEY ,Debug Key" "0,1"
|
|
bitfld.long 0x00 20. " DBGKEY ,Debug Key" "0,1"
|
|
textline " "
|
|
bitfld.long 0x00 19. " S_LOCKUP/DBGKEY ,Core Lockup Status/Debug Key" "Not locked up,Locked up"
|
|
bitfld.long 0x00 18. " S_SLEEP/DBGKEY ,Core Sleep Status/Debug Key" "Not sleeping,Sleeping"
|
|
textline " "
|
|
bitfld.long 0x00 17. " S_HALT/DBGKEY ,Core Halted Status/Debug Key" "Not halted,Halted"
|
|
bitfld.long 0x00 16. " S_REGRDY/DBGKEY ,Register R/W on the Debug Core Register Selector/Debug Key" "Not available,Available"
|
|
textline " "
|
|
bitfld.long 0x00 3. " C_MASKINTS ,Interrupts Mask" "Not masked,Masked"
|
|
bitfld.long 0x00 2. " C_STEP ,Steps the core in halted debug" "Not halted,Halted"
|
|
textline " "
|
|
bitfld.long 0x00 1. " C_HALT ,Core Halted" "Not halted,Halted"
|
|
bitfld.long 0x00 0. " C_DEBUGEN ,Debug Enable" "Disabled,Enabled"
|
|
endif
|
|
endif
|
|
wgroup.long 0xDF4++0x03
|
|
line.long 0x00 "DCRSR,Debug Core Selector Register"
|
|
bitfld.long 0x00 16. " REGWnR ,Register Read/Write" "Read,Write"
|
|
bitfld.long 0x00 0.--4. " REGSEL ,Register Selection" "R0,R1,R2,R3,R4,R5,R6,R7,R8,R9,R10,R11,R12,Current SP,LR,DebugReturnAddress,xPSR Flags,MSP,PSP,Reserved,CONTROL[1]/PRIMASK[0],?..."
|
|
group.long 0xDF8++0x07
|
|
line.long 0x00 "DCRDR,Debug Core Register Data Register"
|
|
hexmask.long 0x00 0.--31. 1. " DATA ,Data for reading and writing registers to and from the processor"
|
|
line.long 0x04 "DEMCR,Debug Exception and Monitor Control Register"
|
|
bitfld.long 0x04 24. " DWTENA ,Global enable or disable for the DW unit" "Disabled,Enabled"
|
|
bitfld.long 0x04 10. " VC_HARDERR ,Debug trap on a Hard Fault" "No error,Error"
|
|
textline " "
|
|
bitfld.long 0x04 0. " VC_CORERESET ,Reset Vector Catch" "No reset,Reset"
|
|
width 0x0B
|
|
else
|
|
newline
|
|
textline "COREDEBUG component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Breakpoint Unit (BPU)"
|
|
sif COMPonent.AVAILABLE("BPU")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("BPU",-1))
|
|
width 8.
|
|
group.long 0x00++0x03
|
|
line.long 0x00 "BP_CTRL,Breakpoint Control Register"
|
|
bitfld.long 0x00 4.--7. " NUM_CODE1 ,Number of comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
bitfld.long 0x00 1. " KEY ,Key field" "No write,Write"
|
|
bitfld.long 0x00 0. " ENABLE ,Breakpoint unit enable bit" "Disabled,Enabled"
|
|
group.long 0x8++0x03
|
|
line.long 0x00 "B_COMP0,Breakpoint Comparator Registers 0"
|
|
bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords"
|
|
hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address"
|
|
bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 0" "Disabled,Enabled"
|
|
group.long 0xC++0x03
|
|
line.long 0x00 "B_COMP1,Breakpoint Comparator Registers 1"
|
|
bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords"
|
|
hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address"
|
|
bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 1" "Disabled,Enabled"
|
|
group.long 0x10++0x03
|
|
line.long 0x00 "B_COMP2,Breakpoint Comparator Registers 2"
|
|
bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords"
|
|
hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address"
|
|
bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 2" "Disabled,Enabled"
|
|
group.long 0x14++0x03
|
|
line.long 0x00 "B_COMP3,Breakpoint Comparator Registers 3"
|
|
bitfld.long 0x00 30.--31. " BP_MATCH ,Happens when the COMP address is matched" "No matching,Lower halfword,Upper halfword,Both halfwords"
|
|
hexmask.long 0x00 2.--28. 2. " COMP ,Comparison address"
|
|
bitfld.long 0x00 0. " ENABLE ,Compare enable for Breakpoint Comparator Register 3" "Disabled,Enabled"
|
|
else
|
|
newline
|
|
textline "BPU component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree "Data Watchpoint and Trace Unit (DWT)"
|
|
sif COMPonent.AVAILABLE("DWT")
|
|
base CONvert.ADDRESSTODUALPORT(COMPonent.BASE("DWT",-1))
|
|
width 14.
|
|
rgroup.long 0x00++0x03
|
|
line.long 0x00 "DW_CTRL,DW Control Register "
|
|
bitfld.long 0x00 28.--31. " NUM_CODE1 ,Number of comparators" "0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15"
|
|
rgroup.long 0x1c++0x03
|
|
line.long 0x00 "DW_PCSR,DW Program Counter Sample Register"
|
|
hexmask.long 0x00 0.--31. 1. " EIASAMPLE ,Execution instruction address sample or 0xFFFFFFFF"
|
|
group.long 0x20++0x0b
|
|
line.long 0x00 "DW_COMP0,DW Comparator Register 0"
|
|
hexmask.long 0x00 0.--31. 1. " COMP1 ,Compare against PC or the data address"
|
|
line.long 0x04 "DW_MASK0,DW Mask Register 0"
|
|
hexmask.long.byte 0x04 0.--4. 1. " MASK ,Mask on data address when matching against COMP"
|
|
line.long 0x08 "DW_FUNCTION0,DW Function Register 0"
|
|
bitfld.long 0x08 24. " MATCHED ,Comparator match" "No match,Match"
|
|
bitfld.long 0x08 0.--3. " FUNCTION , Settings for DW Function Registers" "Disabled,Reserved,Reserved,Reserved,On PC match,Read address,Write address,R/W address,?..."
|
|
group.long 0x30++0x0b
|
|
line.long 0x00 "DW_COMP1,DW Comparator Register 1"
|
|
hexmask.long 0x00 0.--31. 1. " COMP ,Compare against PC or the data address"
|
|
line.long 0x04 "DW_MASK1,DW Mask Register 1 "
|
|
hexmask.long.byte 0x04 0.--4. 1. " MASK ,Mask on data address when matching against COMP"
|
|
line.long 0x08 "DW_FUNCTION1,DW Function Register 1"
|
|
bitfld.long 0x08 24. " MATCHED ,Comparator match" "No match,Match"
|
|
bitfld.long 0x08 0.--3. " FUNCTION , Settings for DW Function Registers" "Disabled,Reserved,Reserved,Reserved,On PC match,Read address,Write address,R/W address,?..."
|
|
else
|
|
newline
|
|
textline "DWT component base address not specified"
|
|
newline
|
|
endif
|
|
tree.end
|
|
tree.end
|
|
AUTOINDENT.POP
|
|
newline
|