woody/Gen4_R-Car_Trace32
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
Files
main
Gen4_R-Car_Trace32/2_Trunk/demo/arm/flash/imx8qx-emmc.cmm
woody d411edd9b4 add Trace32 File
2025-10-14 09:52:32 +09:00

299 lines
7.8 KiB
Plaintext
Raw Permalink Blame History

; --------------------------------------------------------------------------------
; @Title: eMMC Flash program script for IMX8QXP (by FLASH command)
; @Description:
; Prerequisites:
;
; !! No support the empty flash target, because the debugger
; can not access the SECO (Secure Controller) !!
;
; It does not matter of the boot mode (SD/eMMC/QSPI and so on)
;
; @Keywords: ARM, Cortex-M4
; @Author: JIM
; @Board: MCIMX8QXP-CPU
; @Chip: IMX8QXP-CM4
; @Copyright: (C) 1989-2022 Lauterbach GmbH, licensed for use with TRACE32(R) only
; --------------------------------------------------------------------------------
; $Id: imx8qx-emmc.cmm 12049 2023-04-20 12:32:16Z bschroefel $
LOCAL &arg1
ENTRY &arg1
&arg1=STRing.UPpeR("&arg1") // for example "PREPAREONLY"
&MMC_BASE=0x5b010000 ;SDHC1
&ipc_addr=0x41480000 ; CM4_0_MU1_A_BASE , Messaging Unit
; --------------------------------------------------------------------------------
; SYSTEM.UP
; --------------------------------------------------------------------------------
SYStem.RESet
SYStem.CPU IMX8QXP-CM4
SYStem.Option.ResBreak off
SYStem.Mode Attach
IF STATE.RUN()
Break.direct
GOSUB WDOG_DISABLE
GOSUB IOMUX_CONFIG
GOSUB CLOCK_ENABLE
; --------------------------------------------------------------------------------
; Config SDHC1
; --------------------------------------------------------------------------------
Data.Set A:&MMC_BASE+0x04 %LE %Long 0x00010200 ; blk size,cnt
Data.Set A:&MMC_BASE+0x28 %LE %Long 0x08800020 ; bus width, endian
Data.Set A:&MMC_BASE+0x2C %LE %Long 0x008E1088 ; 400KHz clk
Data.Set A:&MMC_BASE+0x34 %LE %Long 0x007F0037 ; BRR,BWR, TCI, CCI interrupt enable
Data.Set A:&MMC_BASE+0x38 %LE %Long 0x007F0037 ; BRR,BWR, TCI, CCI interrupt enable
Data.Set A:&MMC_BASE+0x44 %LE %Long 0x00100010 ;read/write fifo threshold level 64bytes
GOSUB READ_ID_TEST
FLASHFILE.RESet
;FLASHFILE.CONFIG <eMMC controller> <#partition> <0x0>
FLASHFILE.CONFIG &MMC_BASE 0x0
;FLASHFILE.TARGET <<code range>> <<data range>> <<algorithm file>>
FLASHFILE.TARGET 0x20010000++0x2fff 0x20013000++0x1fff ~~/demo/arm/flash/byte/emmc_imx8.bin /KEEP
Data.Set &MMC_BASE+0x2C %LE %Long 0x8e8018 ; 400KHz clk
FLASHFILE.GETID
Data.Set &MMC_BASE+0x2C %LE %Long 0x008E0408 ; 25Mhz clk
FLASHFILE.GETEXTCSD
//End of the test prepareonly
IF "&arg1"=="PREPAREONLY"
ENDDO
FLASHFILE.DUMP 0x0
ENDDO
IOMUX_CONFIG:
(
; --------------------------------------------------------------------------------
; IO Mux for SDHC1
; --------------------------------------------------------------------------------
Data.Set A:&ipc_addr+0x24 %Long 0x0 ; /* Clear GIEn, RIEn, TIEn, GIRn and ABFn. */
// SC_PAD_SET &padNum &mux &ctrl &cfg
GOSUB SC_PAD_SET 9. 0x0 0x21 0x3 ;//SC_P_EMMC0_CLK, 209.==0xD1
GOSUB SC_PAD_SET 10. 0x0 0x21 0x0 ;//SC_P_EMMC0_CMD
GOSUB SC_PAD_SET 11. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA0
GOSUB SC_PAD_SET 12. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA1
GOSUB SC_PAD_SET 13. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA2
GOSUB SC_PAD_SET 14. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA3
GOSUB SC_PAD_SET 16. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA4
GOSUB SC_PAD_SET 17. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA5
GOSUB SC_PAD_SET 18. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA6
GOSUB SC_PAD_SET 19. 0x0 0x21 0x0 ;//SC_P_EMMC0_DATA7
GOSUB SC_PAD_SET 20. 0x0 0x40 0x0 ;//SC_P_EMMC0_STROBE
GOSUB SC_PAD_SET 21. 0x0 0x60 0x0 ;//SC_P_EMMC0_RESET_B
RETURN
)
CLOCK_ENABLE:
(
; --------------------------------------------------------------------------------
; Power ON SDHC1
; --------------------------------------------------------------------------------
// SC_POWER_ON_SET &resource &mode
GOSUB SC_POWER_ON_SET 0xF8 0x03
; --------------------------------------------------------------------------------
; CLK Enable SDHC1
; --------------------------------------------------------------------------------
// SC_CLK_ENABLE &resource &clk
GOSUB SC_CLK_ENABLE 0xF8 0x02
RETURN
)
READ_ID_TEST:
(
//CMD0
RePeaT 2.
(
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x0 ;arg
Data.Set &MMC_BASE+0xc %Long 0x0 ;cmd
WAIT 10.ms
)
//CMD1
RePeaT 10.
(
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x40FF8000 ;arg
Data.Set &MMC_BASE+0xc %Long 0x01020000 ;cmd1
WAIT 100.ms
&resp=Data.Long(A:(&MMC_BASE+0x10))
//print "CMD1 resp: 0x" &resp
IF (&resp&0x80000000)==0x80000000
(
GOTO jump_cmd2
)
)
PRINT "CMD1 fail"
END
jump_cmd2:
//CMD2
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x0 ;arg
Data.Set &MMC_BASE+0xc %Long 0x02010000 ;cmd2
WAIT 10.ms
//CMD3
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x00010000 ; arg, MMC RCA is (0x0001<<16.)
Data.Set &MMC_BASE+0xc %Long 0x03020000 ;cmd3
WAIT 10.ms
//CMD10
Data.Set &MMC_BASE+0x30 %Long 0xFFFFFFFF ;clear status
Data.Set &MMC_BASE+0x8 %Long 0x00010000 ; arg, MMC RCA is (0x0001<<16.)
Data.Set &MMC_BASE+0xc %Long 0x0A010000 ;cmd10
WAIT 10.ms
//Response2
PRINT "CID register"
PRINT "[127:104] 0x" Data.Long(A:(&MMC_BASE+0x1c))
PRINT "[103:72] 0x" Data.Long(A:(&MMC_BASE+0x18))
PRINT "[71:40] 0x" Data.Long(A:(&MMC_BASE+0x14))
PRINT "[39:8] 0x" Data.Long(A:(&MMC_BASE+0x10))
RETURN
)
SC_PAD_SET:
(
ENTRY &padNum &mux &ctrl &cfg
&data=0x00000001 ;version
&data=&data|0x00000400 ;message size
&data=&data|0x00060000 ;svc_pad
&data=&data|0x05000000 ;func
;wait until Tx buffer empty
Data.Set A:&ipc_addr %Long &data
Data.Set A:&ipc_addr+0x4 %Long &ctrl
&data=&padNum
&data=&data|(&mux<<16.)
&data=&data|(&cfg<<24.)
Data.Set A:&ipc_addr+0x8 %Long &data
Data.Set A:&ipc_addr+0xC %Long 0x00
&status=Data.Long(A:&ipc_addr+0x20)
&rxBuff=(&ipc_addr+0x10)
WHILE (((&status>>24.)&0xF)!=0)
(
&data=Data.Long(A:&rxBuff)
&rxBuff=&rxBuff+0x4
&status=Data.Long(A:&ipc_addr+0x20)
)
RETURN
)
//Power_ON_SDHC1
SC_POWER_ON_SET:
(
ENTRY &resource &mode
&data=0x00000001 ;version
&data=&data|0x00000200 ;message size
&data=&data|0x00020000 ;svc_pm
&data=&data|0x03000000 ;func, POWER_MODE
;wait until Tx buffer empty
Data.Set A:&ipc_addr %Long &data
&data=&resource
&data=&data|(&mode<<16.)
&data=&data|0x07000000
Data.Set A:&ipc_addr+0x4 %Long &data
&status=Data.Long(A:&ipc_addr+0x20)
&rxBuff=(&ipc_addr+0x10)
WHILE (((&status>>24.)&0xF)!=0)
(
&data=Data.Long(A:&rxBuff)
&rxBuff=&rxBuff+0x4
&status=Data.Long(A:&ipc_addr+0x20)
)
wait 200.ms ;dummy wait
RETURN
)
//Clock_Enable_SDHC1
SC_CLK_ENABLE:
(
ENTRY &resource &clk
&data=0x00000001 ;version
&data=&data|0x00000300 ;message size
&data=&data|0x00020000 ;svc_pm
&data=&data|0x07000000 ;func, POWER_MODE
;wait until Tx buffer empty
Data.Set A:&ipc_addr %Long &data
&data=&resource
&data=&data|(&clk<<16.)
&data=&data|0x01000000
Data.Set A:&ipc_addr+0x4 %Long &data
;&data=0x00CA0001
&data=0x00C81301 ;imx8qx
Data.Set A:&ipc_addr+0x8 %Long &data
&status=Data.Long(A:&ipc_addr+0x20)
&rxBuff=(&ipc_addr+0x10)
WHILE (((&status>>24.)&0xF)!=0)
(
&data=Data.Long(A:&rxBuff)
&rxBuff=&rxBuff+0x4
&status=Data.Long(A:&ipc_addr+0x20)
)
wait 200.ms ;dummy wait
RETURN
)
//Watchdog disable
WDOG_DISABLE:
(
//the changing wdog register works only internal code running not by a cmm script.
//Data.Set SD:0x41420004 %LE %Long 0xd928c520 ;unlock
//Data.Set SD:0x41420000 %LE %Long (data.long(SD:0x41420000)&~0x80) ;disable watchdog
&WDOG_CS=Data.Long(SD:0x41420000)&~0x80
Register.Set r0 0x41420000
Register.Set r1 0xd928c520
Register.Set r2 &WDOG_CS
Data.Assemble ST:0x20000800 str r1,[r0,#0x4]
Data.Assemble ST:0x20000802 str r2,[r0]
Data.Assemble ST:0x20000804 b 0x20000804
Register.Set pc 0x20000800
Break.Set 0x20000804
Go
WAIT !STATE.RUN()
RETURN
)
Reference in New Issue View Git Blame Copy Permalink